Search Results

Search found 8228 results on 330 pages for 'card reader'.

Page 302/330 | < Previous Page | 298 299 300 301 302 303 304 305 306 307 308 309  | Next Page >

• No sound lenovo t60 alsa ad1981 iec958

  - by Nate

  Any help on getting the sound to come through my lenovo t60 build in speakers, headphones, or mic would greatly be appreciated. The three buttons to increase, decrease sound seem to work. Bios has sound card enabled and the buttons beep when pressed. When going to Utube or playing music, no sound is heard. Thanks Nate Feb 23 - Didn't see anything specific in the sys logs with Rhythmbox when connecting my ipod. Rhythmbox is playing, but still no sound. Here is the syslog details for today. Output is set to analog output. Feb 23 17:42:32 itgis01398 rsyslogd: [origin software="rsyslogd" swVersion="4.2.0" x-pid="824" x-info="http://www.rsyslog.com"] rsyslogd was HUPed, type 'lightweight'. Feb 23 17:42:33 itgis01398 rsyslogd: [origin software="rsyslogd" swVersion="4.2.0" x-pid="824" x-info="http://www.rsyslog.com"] rsyslogd was HUPed, type 'lightweight'. Feb 23 17:42:49 itgis01398 anacron[968]: Job `cron.daily' terminated Feb 23 17:42:49 itgis01398 anacron[968]: Job `cron.weekly' started Feb 23 17:42:49 itgis01398 anacron[12067]: Updated timestamp for job `cron.weekly' to 2011-02-23 Feb 23 17:42:53 itgis01398 anacron[968]: Job `cron.weekly' terminated Feb 23 17:42:53 itgis01398 anacron[968]: Normal exit (2 jobs run) Feb 23 18:01:19 itgis01398 kernel: [ 2731.324067] usb 1-5: new high speed USB device using ehci_hcd and address 3 Feb 23 18:01:19 itgis01398 kernel: [ 2731.482879] Initializing USB Mass Storage driver... Feb 23 18:01:19 itgis01398 kernel: [ 2731.483061] usb-storage 1-5:1.0: Quirks match for vid 05ac pid 1205: 10 Feb 23 18:01:19 itgis01398 kernel: [ 2731.483116] scsi6 : usb-storage 1-5:1.0 Feb 23 18:01:19 itgis01398 kernel: [ 2731.483306] usbcore: registered new interface driver usb-storage Feb 23 18:01:19 itgis01398 kernel: [ 2731.483310] USB Mass Storage support registered. Feb 23 18:01:20 itgis01398 kernel: [ 2732.481116] scsi 6:0:0:0: Direct-Access Apple iPod 1.62 PQ: 0 ANSI: 0 Feb 23 18:01:20 itgis01398 kernel: [ 2732.482466] sd 6:0:0:0: Attached scsi generic sg2 type 0 Feb 23 18:01:20 itgis01398 kernel: [ 2732.485095] sd 6:0:0:0: [sdb] Adjusting the sector count from its reported value: 7999488 Feb 23 18:01:20 itgis01398 kernel: [ 2732.485110] sd 6:0:0:0: [sdb] 7999487 512-byte logical blocks: (4.09 GB/3.81 GiB) Feb 23 18:01:20 itgis01398 kernel: [ 2732.487933] sd 6:0:0:0: [sdb] Write Protect is off Feb 23 18:01:20 itgis01398 kernel: [ 2732.487941] sd 6:0:0:0: [sdb] Mode Sense: 64 00 00 08 Feb 23 18:01:20 itgis01398 kernel: [ 2732.487947] sd 6:0:0:0: [sdb] Assuming drive cache: write through Feb 23 18:01:20 itgis01398 kernel: [ 2732.489927] sd 6:0:0:0: [sdb] Adjusting the sector count from its reported value: 7999488 Feb 23 18:01:20 itgis01398 kernel: [ 2732.491150] sd 6:0:0:0: [sdb] Assuming drive cache: write through Feb 23 18:01:20 itgis01398 kernel: [ 2732.491163] sdb: sdb1 sdb2 Feb 23 18:01:20 itgis01398 kernel: [ 2732.510428] sd 6:0:0:0: [sdb] Adjusting the sector count from its reported value: 7999488 Feb 23 18:01:20 itgis01398 kernel: [ 2732.511288] sd 6:0:0:0: [sdb] Assuming drive cache: write through Feb 23 18:01:20 itgis01398 kernel: [ 2732.511297] sd 6:0:0:0: [sdb] Attached SCSI removable disk Feb 23 18:01:21 itgis01398 kernel: [ 2733.746675] FAT: invalid media value (0x2f) Feb 23 18:01:21 itgis01398 kernel: [ 2733.746682] VFS: Can't find a valid FAT filesystem on dev sdb1. Feb 23 18:01:22 itgis01398 upstart-udev-bridge[330]: Env must be KEY=VALUE pairs Feb 23 18:02:07 itgis01398 kernel: [ 2780.115826] sd 6:0:0:0: [sdb] Unhandled sense code Feb 23 18:02:07 itgis01398 kernel: [ 2780.115835] sd 6:0:0:0: [sdb] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE Feb 23 18:02:07 itgis01398 kernel: [ 2780.115844] sd 6:0:0:0: [sdb] Sense Key : Medium Error [current] Feb 23 18:02:07 itgis01398 kernel: [ 2780.115855] Info fld=0x0 Feb 23 18:02:07 itgis01398 kernel: [ 2780.115859] sd 6:0:0:0: [sdb] Add. Sense: Unrecovered read error Feb 23 18:02:07 itgis01398 kernel: [ 2780.115870] sd 6:0:0:0: [sdb] CDB: Read(10): 28 00 00 08 fd e9 00 00 f0 00 Feb 23 18:02:07 itgis01398 kernel: [ 2780.115892] end_request: I/O error, dev sdb, sector 589289 Feb 23 18:02:49 itgis01398 kernel: [ 2821.351464] sd 6:0:0:0: [sdb] Unhandled sense code Feb 23 18:02:49 itgis01398 kernel: [ 2821.351473] sd 6:0:0:0: [sdb] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE Feb 23 18:02:49 itgis01398 kernel: [ 2821.351482] sd 6:0:0:0: [sdb] Sense Key : Medium Error [current] Feb 23 18:02:49 itgis01398 kernel: [ 2821.351493] Info fld=0x0 Feb 23 18:02:49 itgis01398 kernel: [ 2821.351497] sd 6:0:0:0: [sdb] Add. Sense: No additional sense information Feb 23 18:02:49 itgis01398 kernel: [ 2821.351507] sd 6:0:0:0: [sdb] CDB: Read(10): 28 00 00 08 fe d9 00 00 10 00 Feb 23 18:02:49 itgis01398 kernel: [ 2821.351530] end_request: I/O error, dev sdb, sector 589529 Feb 23 18:17:01 itgis01398 CRON[12709]: (root) CMD ( cd / && run-parts --report /etc/cron.hourly) volume is all of the way up.

  Read the article

• Old School Wizardry Tip: Batch File Comments

  - by jkauffman

  Johnny, the Endangered Keyboard-Driven Windows User Some of my proudest, obscure Windows tricks are losing their relevance. I know I’m not alone. Keyboard shortcuts are going the way of the dodo. I used to induce fearful awe by slapping Ctrl+Shift+Esc in front of the lowly, pedestrian Windows users. No windows key on the keyboard? No problem: Ctrl+Esc. No menu key on the keyboard: Shift+F10. I am also firmly planted in the habit of closing windows with the Alt+Space menu (Alt+Space, C); and I harbor a brooding, slow=growing list of programs that fail to support this correctly (that means you, Paint.NET). Every time a new version of windows comes out, the support for some of these minor time-saving habits get pared out. Will I complain publicly? Nope, I know my old ways should be axed to conserve precious design energy. In fact, I disapprove of fierce un-intuitiveness for the sake of alleged productivity. Like vim, for example. If you approach a program after being away for 5 years, having to recall encyclopedic knowledge is a flaw. The RTFM disciples have lost. Anyway, some of the items in my arsenal of goofy time-saving tricks are still relevant today. I wanted to draw attention to one that’s stood the test of time. Remember Batch Files? Yes, it’s true, batch files are fading faster than the world of print. But they're not dead yet. I still run into some situations where I opt to use batch files. They are still relevant for build processes, or just various development workflow tools. Sure, there’s powershell, but there’s that stupid Set-ExecutionPolicy speed bump standing in your way; can you really spare the time to A) hunt down that setting on all machines affected and/or B) make futile efforts to convince your coworkers/boss that the hassle was worth it? When possible, I prefer the batch file wild card. And whenever I return to batch files, I end up researching some of the unintuitive aspects such as parameters, quote handling, and ERRORLEVEL. But I never have to remember to use “REM” for comment lines, because there’s a cleaner way to do them! Double Colon For Eye-Friendly Comments Here is a very simple batch file, with pretty much minimal content: @ECHO OFF SETLOCAL REM This is a comment ECHO This batch file doesn’t do much If you code on a daily basis, this may be more suitable to your eyes: @ECHO OFF SETLOCAL :: This is a comment ECHO This batch file doesn’t do much Works great! I imagine I find it preferable due to the similarity to comments in other situations: // or ;  or # I’ve often make visual pseudo-line breaks in my code, and this colon-based syntax works wonders: @ECHO OFF SETLOCAL :: Do stuff ECHO Doing Stuff :::::::::::::::::::::::::::: :: Do more stuff ECHO This batch file doesn’t do much Not only is it more readable, but there’s a slight performance benefit. The batch file engine sees this as an invalid line label and immediately reads the following line. Use that fact to your advantage if this trick leads you into heated nerd debate. Two Pitfalls to Avoid Be aware of that there are a couple situations where this hack will fail you. It most likely won’t be a problem unless you’re getting really sophisticated with your batch files. Pitfall #1: Inline comments @ECHO OFF SETLOCAL IF EXIST C:\SomeFile.txt GOTO END ::This will fail :END Unfortunately, this fails. You can only have whitespace to the left of your comments. Pitfall #2: Code Blocks @ECHO OFF SETLOCAL IF EXIST C:\SomeFile.txt (         :: This will fail         ECHO HELLO ) Code blocks, such as if statements and for loops, cannot contain these comments. This is ultimately due to the fact that entire code blocks are processed as a single line. I originally learned this from Rob van der Woude’s site. He goes into more depth about the behavior of the pitfalls as well, if you are interested in further details. I hope this trick earns you serious geek rep!

  Read the article

• SQL SERVER – Why Do We Need Master Data Management – Importance and Significance of Master Data Management (MDM)

  - by pinaldave

  Let me paint a picture of everyday life for you.  Let’s say you and your wife both have address books for your groups of friends.  There is definitely overlap between them, so that you both have the addresses for your mutual friends, and there are addresses that only you know, and some only she knows.  They also might be organized differently.  You might list your friend under “J” for “Joe” or even under “W” for “Work,” while she might list him under “S” for “Joe Smith” or under your name because he is your friend.  If you happened to trade, neither of you would be able to find anything! This is where data management would be very important.  If you were to consolidate into one address book, you would have to set rules about how to organize the book, and both of you would have to follow them.  You would also make sure that poor Joe doesn’t get entered twice under “J” and under “S.” This might be a familiar situation to you, whether you are thinking about address books, record collections, books, or even shopping lists.  Wherever there is a lot of data to consolidate, you are going to run into problems unless everyone is following the same rules. I’m sure that my readers can figure out where I am going with this.  What is SQL Server but a computerized way to organize data?  And Microsoft is making it easier and easier to get all your “addresses” into one place.  In the  2008 version of SQL they introduced a new tool called Master Data Services (MDS) for Master Data Management, and they have improved it for the new 2012 version. MDM was hailed as a major improvement for business intelligence.  You might not think that an organizational system is terribly exciting, but think about the kind of “address books” a company might have.  Many companies have lots of important information, like addresses, credit card numbers, purchase history, and so much more.  To organize all this efficiently so that customers are well cared for and properly billed (only once, not never or multiple times!) is a major part of business intelligence. MDM comes into play because it will comb through these mountains of data and make sure that all the information is consistent, accurate, and all placed in one database so that employees don’t have to search high and low and waste their time. MDM also has operational MDM functions.  This is not a redundancy.  Operational MDM means that when one employee updates one bit of information in the database, for example – updating a new address for a customer, operational MDM ensures that this address is updated throughout the system so that all departments will have the correct information. Another cool thing about MDM is that it features Master Data Services Configuration Manager, which is exactly what it sounds like.  It has a built-in “helper” that lets you set up your database quickly, easily, and with the correct configurations.  While talking about cool features, I can’t skip over the add-in for Excel.  This allows you to link certain data to Excel files for easier sharing and uploading. In summary, I want to emphasize that the scariest part of the database is slowly disappearing.  Everyone knows that a database – one consolidated area for all your data – is a good idea, but the idea of setting one up is daunting.  But SQL Server is making data management easier and easier with features like Master Data Services (MDS). Reference: Pinal Dave (http://blog.SQLAuthority.com) Filed under: PostADay, SQL, SQL Authority, SQL Query, SQL Server, SQL Tips and Tricks, T SQL, Technology Tagged: Master Data Services, MDM

  Read the article

• What's up with LDoms: Part 9 - Direct IO

  - by Stefan Hinker

  In the last article of this series, we discussed the most general of all physical IO options available for LDoms, root domains.  Now, let's have a short look at the next level of granularity: Virtualizing individual PCIe slots.  In the LDoms terminology, this feature is called "Direct IO" or DIO.  It is very similar to root domains, but instead of reassigning ownership of a complete root complex, it only moves a single PCIe slot or endpoint device to a different domain.  Let's look again at hardware available to mars in the original configuration: root@sun:~# ldm ls-io NAME TYPE BUS DOMAIN STATUS ---- ---- --- ------ ------ pci_0 BUS pci_0 primary pci_1 BUS pci_1 primary pci_2 BUS pci_2 primary pci_3 BUS pci_3 primary /SYS/MB/PCIE1 PCIE pci_0 primary EMP /SYS/MB/SASHBA0 PCIE pci_0 primary OCC /SYS/MB/NET0 PCIE pci_0 primary OCC /SYS/MB/PCIE5 PCIE pci_1 primary EMP /SYS/MB/PCIE6 PCIE pci_1 primary EMP /SYS/MB/PCIE7 PCIE pci_1 primary EMP /SYS/MB/PCIE2 PCIE pci_2 primary EMP /SYS/MB/PCIE3 PCIE pci_2 primary OCC /SYS/MB/PCIE4 PCIE pci_2 primary EMP /SYS/MB/PCIE8 PCIE pci_3 primary EMP /SYS/MB/SASHBA1 PCIE pci_3 primary OCC /SYS/MB/NET2 PCIE pci_3 primary OCC /SYS/MB/NET0/IOVNET.PF0 PF pci_0 primary /SYS/MB/NET0/IOVNET.PF1 PF pci_0 primary /SYS/MB/NET2/IOVNET.PF0 PF pci_3 primary /SYS/MB/NET2/IOVNET.PF1 PF pci_3 primary All of the "PCIE" type devices are available for SDIO, with a few limitations.  If the device is a slot, the card in that slot must support the DIO feature.  The documentation lists all such cards.  Moving a slot to a different domain works just like moving a PCI root complex.  Again, this is not a dynamic process and includes reboots of the affected domains.  The resulting configuration is nicely shown in a diagram in the Admin Guide: There are several important things to note and consider here: The domain receiving the slot/endpoint device turns into an IO domain in LDoms terminology, because it now owns some physical IO hardware. Solaris will create nodes for this hardware under /devices.  This includes entries for the virtual PCI root complex (pci_0 in the diagram) and anything between it and the actual endpoint device.  It is very important to understand that all of this PCIe infrastructure is virtual only!  Only the actual endpoint devices are true physical hardware. There is an implicit dependency between the guest owning the endpoint device and the root domain owning the real PCIe infrastructure: Only if the root domain is up and running, will the guest domain have access to the endpoint device. The root domain is still responsible for resetting and configuring the PCIe infrastructure (root complex, PCIe level configurations, error handling etc.) because it owns this part of the physical infrastructure. This also means that if the root domain needs to reset the PCIe root complex for any reason (typically a reboot of the root domain) it will reset and thus disrupt the operation of the endpoint device owned by the guest domain.  The result in the guest is not predictable.  I recommend to configure the resulting behaviour of the guest using domain dependencies as described in the Admin Guide in Chapter "Configuring Domain Dependencies". Please consult the Admin Guide in Section "Creating an I/O Domain by Assigning PCIe Endpoint Devices" for all the details! As you can see, there are several restrictions for this feature.  It was introduced in LDoms 2.0, mainly to allow the configuration of guest domains that need access to tape devices.  Today, with the higher number of PCIe root complexes and the availability of SR-IOV, the need to use this feature is declining.  I personally do not recommend to use it, mainly because of the drawbacks of the depencies on the root domain and because it can be replaced with SR-IOV (although then with similar limitations). This was a rather short entry, more for completeness.  I believe that DIO can usually be replaced by SR-IOV, which is much more flexible.  I will cover SR-IOV in the next section of this blog series.

  Read the article

• SQL analytical mash-ups deliver real-time WOW! for big data

  - by KLaker

  One of the overlooked capabilities of SQL as an analysis engine, because we all just take it for granted, is that you can mix and match analytical features to create some amazing mash-ups. As we move into the exciting world of big data these mash-ups can really deliver those "wow, I never knew that" moments. While Java is an incredibly flexible and powerful framework for managing big data there are some significant challenges in using Java and MapReduce to drive your analysis to create these "wow" discoveries. One of these "wow" moments was demonstrated at this year's OpenWorld during Andy Mendelsohn's general keynote session.  Here is the scenario - we are looking for fraudulent activities in our big data stream and in this case we identifying potentially fraudulent activities by looking for specific patterns. We using geospatial tagging of each transaction so we can create a real-time fraud-map for our business users. Where we start to move towards a "wow" moment is to extend this basic use of spatial and pattern matching, as shown in the above dashboard screen, to incorporate spatial analytics within the SQL pattern matching clause. This will allow us to compute the distance between transactions. Apologies for the quality of this screenshot….hopefully below you see where we have extended our SQL pattern matching clause to use location of each transaction and to calculate the distance between each transaction: This allows us to compare the time of the last transaction with the time of the current transaction and see if the distance between the two points is possible given the time frame. Obviously if I buy something in Florida from my favourite bike store (may be a new carbon saddle for my Trek) and then 5 minutes later the system sees my credit card details being used in Arizona there is high probability that this transaction in Arizona is actually fraudulent (I am fast on my Trek but not that fast!) and we can flag this up in real-time on our dashboard: In this post I have used the term "real-time" a couple of times and this is an important point and one of the key reasons why SQL really is the only language to use if you want to analyse  big data. One of the most important questions that comes up in every big data project is: how do we do analysis? Many enlightened customers are now realising that using Java-MapReduce to deliver analysis does not result in "wow" moments. These "wow" moments only come with SQL because it is offers a much richer environment, it is simpler to use and it is faster - which makes it possible to deliver real-time "Wow!". Below is a slide from Andy's session showing the results of a comparison of Java-MapReduce vs. SQL pattern matching to deliver our "wow" moment during our live demo.  You can watch our analytical mash-up "Wow" demo that compares the power of 12c SQL pattern matching + spatial analytics vs. Java-MapReduce  here: You can get more information about SQL Pattern Matching on our SQL Analytics home page on OTN, see here http://www.oracle.com/technetwork/database/bi-datawarehousing/sql-analytics-index-1984365.html.  You can get more information about our spatial analytics here: http://www.oracle.com/technetwork/database-options/spatialandgraph/overview/index.html If you would like to watch the full Database 12c OOW presentation see here: http://medianetwork.oracle.com/video/player/2686974264001

  Read the article

• How to get bearable 2D and 3D performance on AMD Radeon HD 6950?

  - by l0b0

  I have had an AMD Radeon HD 6950 (i.e., Cayman series) for a couple years now, and I have tried a lot of combinations of drivers and settings with terrible results. I'm completely at a loss as to how to proceed. The open source driver has much better 2D performance, but it offloads all OpenGL rendering to the CPU. What I've tried so far: All the latest stable Ubuntu releases in the period, plus one Linux Mint release. All the latest stable AMD Catalyst Proprietary Display Drivers, and currently 13.1. The unofficial wiki installation instructions for every Ubuntu version and the semi-official Ubuntu instructions. All the tips and tweaks I could find for Minecraft (Optifine, reducing settings to minimum), VLC (postprocessing at minimum, rendering at native video size), Catalyst Control Center (flipped every lever in there) and X11 (some binary toggles I can no longer remember). Results: Typically 13-15 FPS in Minecraft, 30 max (100+ in Windows with the same driver version). Around 10 FPS in Team Fortress 2 using the official Steam client. Choppy video playback, in Flash and with VLC. CPU use goes through the roof when rendering video (150% for 1080p on YouTube in Chromium, 100% for 1080p H264 in VLC). glxgears shows 12.5 FPS when maximized. fgl_glxgears shows 10 FPS when maximized. Hardware details from lshw: Motherboard ASUS P6X58D-E CPU Intel Core i7 CPU 950 @ 3.07GHz (never overclocked; 64 bit) 6 GB RAM Video card product "Cayman PRO [Radeon HD 6950]", vendor "Hynix Semiconductor (Hyundai Electronics)" 2 x 1920x1200 monitors, both connected with HDMI. I feel I must be missing something absolutely fundamental here. Is there no accelerated support for anything on 64-bit architectures? Does a dual monitor completely mess up the driver? $ fglrxinfo display: :0 screen: 0 OpenGL vendor string: Advanced Micro Devices, Inc. OpenGL renderer string: AMD Radeon HD 6900 Series OpenGL version string: 4.2.11995 Compatibility Profile Context $ glxinfo | grep 'direct rendering' direct rendering: Yes I am currently using the open source driver, with the following results: Full frame rate and low CPU load when playing 1080p video. Black screen (but music in the background) in Team Fortress 2. Similar performance in Minecraft as the Catalyst driver. In hindsight obvious, since both end up offloading the rendering to the CPU. My /var/log/Xorg.0.log after upgrading to AMD Catalyst 13.1. Some possibly important lines: (WW) Falling back to old probe method for fglrx (WW) fglrx: No matching Device section for instance (BusID PCI:0@3:0:1) found The generated xorg.conf. The disabled "monitor" 0-DFP9 is actually an A/V receiver, which sometimes confuses the monitor drivers when turned on/off (but not in Windows). All three "monitor" devices are connected with HDMI. Edit: Chris Carter's suggestion to use the xorg-edgers PPA (Catalyst 13.1) resulted in some improvement, but still pretty bad performance overall: Minecraft stabilizes at 13-17 FPS, but at least the CPU load is "only" at 45-60%. Still 150% CPU use for 1080p video rendering on YouTube in Chromium. Massive improvement for 1080p H264 in VLC: 40-50% CPU use and no visible jitter glxgears performance about doubled to 25-30 FPS when maximized. fgl_glxgears still at ~10 FPS when maximized.

  Read the article

• How to build a Singleton-like dependency injector replacement (Php)

  - by Erparom

  I know out there are a lot of excelent containers, even frameworks almost entirely DI based with good strong IoC classes. However, this doesn't help me to "define" a new pattern. (This is Php code but understandable to anyone) Supose we have: //Declares the singleton class bookSingleton { private $author; private static $bookInstance; private static $isLoaned = FALSE; //The private constructor private function __constructor() { $this->author = "Onecrappy Writer Ofcheap Novels"; } //Sets the global isLoaned state and also gets self instance public static function loanBook() { if (self::$isLoaned === FALSE) { //Book already taken, so return false return FALSE; } else { //Ok, not loaned, lets instantiate (if needed and loan) if (!isset(self::$bookInstance)) { self::$bookInstance = new BookSingleton(); } self::$isLoaned = TRUE; } } //Return loaned state to false, so another book reader can take the book public function returnBook() { $self::$isLoaned = FALSE; } public function getAuthor() { return $this->author; } } Then we get the singelton consumtion class: //Consumes the Singleton class BookBorrower() { private $borrowedBook; private $haveBookState; public function __construct() { this->haveBookState = FALSE; } //Use the singelton-pattern behavior public function borrowBook() { $this->borrowedBook = BookSingleton::loanBook(); //Check if was successfully borrowed if (!this->borrowedBook) { $this->haveBookState = FALSE; } else { $this->haveBookState = TRUE; } } public function returnBook() { $this->borrowedBook->returnBook(); $this->haveBookState = FALSE; } public function getBook() { if ($this->haveBookState) { return "The book is loaned, the author is" . $this->borrowedbook->getAuthor(); } else { return "I don't have the book, perhaps someone else took it"; } } } At last, we got a client, to test the behavior function __autoload($class) { require_once $class . '.php'; } function write ($whatever,$breaks) { for($break = 0;$break<$breaks;$break++) { $whatever .= "\n"; } echo nl2br($whatever); } write("Begin Singleton test", 2); $borrowerJuan = new BookBorrower(); $borrowerPedro = new BookBorrower(); write("Juan asks for the book", 1); $borrowerJuan->borrowBook(); write("Book Borrowed? ", 1); write($borrowerJuan->getAuthorAndTitle(),2); write("Pedro asks for the book", 1); $borrowerPedro->borrowBook(); write("Book Borrowed? ", 1); write($borrowerPedro->getAuthorAndTitle(),2); write("Juan returns the book", 1); $borrowerJuan->returnBook(); write("Returned Book Juan? ", 1); write($borrowerJuan->getAuthorAndTitle(),2); write("Pedro asks again for the book", 1); $borrowerPedro->borrowBook(); write("Book Borrowed? ", 1); write($borrowerPedro->getAuthorAndTitle(),2); This will end up in the expected behavior: Begin Singleton test Juan asks for the book Book Borrowed? The book is loaned, the author is = Onecrappy Writer Ofcheap Novels Pedro asks for the book Book Borrowed? I don't have the book, perhaps someone else took it Juan returns the book Returned Book Juan? I don't have the book, perhaps someone else took it Pedro asks again for the book Book Borrowed? The book is loaned, the author is = Onecrappy Writer Ofcheap Novels So I want to make a pattern based on the DI technique able to do exactly the same, but without singleton pattern. As far as I'm aware, I KNOW I must inject the book inside "borrowBook" function instead of taking a static instance: public function borrowBook(BookNonSingleton $book) { if (isset($this->borrowedBook) || $book->isLoaned()) { $this->haveBook = FALSE; return FALSE; } else { $this->borrowedBook = $book; $this->haveBook = TRUE; return TRUE; } } And at the client, just handle the book: $borrowerJuan = new BookBorrower(); $borrowerJuan-borrowBook(new NonSingletonBook()); Etc... and so far so good, BUT... Im taking the responsability of "single instance" to the borrower, instead of keeping that responsability inside the NonSingletonBook, that since it has not anymore a private constructor, can be instantiated as many times... making instances on each call. So, What does my NonSingletonBook class MUST be in order to never allow borrowers to have this same book twice? (aka) keep the single instance. Because the dependency injector part of the code (borrower) does not solve me this AT ALL. Is it needed the container with an "asShared" method builder with static behavior? No way to encapsulate this functionallity into the Book itself? "Hey Im a book and I shouldn't be instantiated more than once, I'm unique"

  Read the article

• SQL SERVER – Puzzle #1 – Querying Pattern Ranges and Wild Cards

  - by Pinal Dave

  Note: Read at the end of the blog post how you can get five Joes 2 Pros Book #1 and a surprise gift. I have been blogging for almost 7 years and every other day I receive questions about Querying Pattern Ranges. The most common way to solve the problem is to use Wild Cards. However, not everyone knows how to use wild card properly. SQL Queries 2012 Joes 2 Pros Volume 1 – The SQL Queries 2012 Hands-On Tutorial for Beginners Book On Amazon | Book On Flipkart Learn SQL Server get all the five parts combo kit Kit on Amazon | Kit on Flipkart Many people know wildcards are great for finding patterns in character data. There are also some special sequences with wildcards that can give you even more power. This series from SQL Queries 2012 Joes 2 Pros® Volume 1 will show you some of these cool tricks. All supporting files are available with a free download from the www.Joes2Pros.com web site. This example is from the SQL 2012 series Volume 1 in the file SQLQueries2012Vol1Chapter2.2Setup.sql. If you need help setting up then look in the “Free Videos” section on Joes2Pros under “Getting Started” called “How to install your labs” Querying Pattern Ranges The % wildcard character represents any number of characters of any length. Let’s find all first names that end in the letter ‘A’. By using the percentage ‘%’ sign with the letter ‘A’, we achieve this goal using the code sample below: SELECT * FROM Employee WHERE FirstName LIKE '%A' To find all FirstName values beginning with the letters ‘A’ or ‘B’ we can use two predicates in our WHERE clause, by separating them with the OR statement. Finding names beginning with an ‘A’ or ‘B’ is easy and this works fine until we want a larger range of letters as in the example below for ‘A’ thru ‘K’: SELECT * FROM Employee WHERE FirstName LIKE 'A%' OR FirstName LIKE 'B%' OR FirstName LIKE 'C%' OR FirstName LIKE 'D%' OR FirstName LIKE 'E%' OR FirstName LIKE 'F%' OR FirstName LIKE 'G%' OR FirstName LIKE 'H%' OR FirstName LIKE 'I%' OR FirstName LIKE 'J%' OR FirstName LIKE 'K%' The previous query does find FirstName values beginning with the letters ‘A’ thru ‘K’. However, when a query requires a large range of letters, the LIKE operator has an even better option. Since the first letter of the FirstName field can be ‘A’, ‘B’, ‘C’, ‘D’, ‘E’, ‘F’, ‘G’, ‘H’, ‘I’, ‘J’ or ‘K’, simply list all these choices inside a set of square brackets followed by the ‘%’ wildcard, as in the example below: SELECT * FROM Employee WHERE FirstName LIKE '[ABCDEFGHIJK]%' A more elegant example of this technique recognizes that all these letters are in a continuous range, so we really only need to list the first and last letter of the range inside the square brackets, followed by the ‘%’ wildcard allowing for any number of characters after the first letter in the range. Note: A predicate that uses a range will not work with the ‘=’ operator (equals sign). It will neither raise an error, nor produce a result set. --Bad query (will not error or return any records) SELECT * FROM Employee WHERE FirstName = '[A-K]%' Question: You want to find all first names that start with the letters A-M in your Customer table and end with the letter Z. Which SQL code would you use? a. SELECT * FROM Customer WHERE FirstName LIKE 'm%z' b. SELECT * FROM Customer WHERE FirstName LIKE 'a-m%z' c. SELECT * FROM Customer WHERE FirstName LIKE 'a-m%z' d. SELECT * FROM Customer WHERE FirstName LIKE '[a-m]%z' e. SELECT * FROM Customer WHERE FirstName LIKE '[a-m]z%' f. SELECT * FROM Customer WHERE FirstName LIKE '[a-m]%z' g. SELECT * FROM Customer WHERE FirstName LIKE '[a-m]z%' Contest Leave a valid answer before June 18, 2013 in the comment section. 5 winners will be selected from all the valid answers and will receive Joes 2 Pros Book #1. 1 Lucky person will get a surprise gift from Joes 2 Pros. The contest is open for all the countries where Amazon ships the book (USA, UK, Canada, India and many others). Special Note: Read all the options before you provide valid answer as there is a small trick hidden in answers. Reference: Pinal Dave (http://blog.sqlauthority.com) Filed under: Joes 2 Pros, PostADay, SQL, SQL Authority, SQL Puzzle, SQL Query, SQL Server, SQL Tips and Tricks, T SQL, Technology

  Read the article

• Where Facebook Stands Heading Into 2013

  - by Mike Stiles

  In our last blog, we looked at how Twitter is positioned heading into 2013. Now it’s time to take a similar look at Facebook. 2012, for a time at least, seemed to be the era of Facebook-bashing. Between a far-from-smooth IPO, subsequent stock price declines, and anxiety over privacy, the top social network became a target for comedians, politicians, business journalists, and of course those who were prone to Facebook-bash even in the best of times. But amidst the “this is the end of Facebook” headlines, the company kept experimenting, kept testing, kept innovating, and pressing forward, committed as always to the user experience, while concurrently addressing monetization with greater urgency. Facebook enters 2013 with over 1 billion users around the world. Usage grew 41% in Brazil, Russia, Japan, South Korea and India in 2012. In the Middle East and North Africa, an average 21 new signups happen per minute. Engagement and time spent on the site would impress the harshest of critics. Facebook, while not bulletproof, has become such an integrated daily force in users’ lives, it’s getting hard to imagine any future mass rejection. You want to see a company recognizing weaknesses and shoring them up. Mobile was a weakness in 2012 as Facebook was one of many caught by surprise at the speed of user migration to mobile. But new mobile interfaces, better mobile ads, speed upgrades, standalone Messenger and Pages mobile apps, and the big dollar acquisition of Instagram, were a few indicators Facebook won’t play catch-up any more than it has to. As a user, the cool thing about Facebook is, it knows you. The uncool thing about Facebook is, it knows you. The company’s walking a delicate line between the public’s competing desires for customized experiences and privacy. While the company’s working to make privacy options clearer and easier, Facebook’s Paul Adams says data aggregation can move from acting on what a user is engaging with at the moment to a more holistic view of what they’re likely to want at any given time. To help learn about you, there’s Open Graph. Embedded through diverse partnerships, the idea is to surface what you’re doing and what you care about, and help you discover things via your friends’ activities. Facebook’s Director of Engineering, Mike Vernal, says building mobile social apps connected to Facebook in such ways is the next wave of big innovation. Expect to see that fostered in 2013. The Facebook site experience is always evolving. Some users like that about Facebook, others can’t wait to complain about it…on Facebook. The Facebook focal point, the News Feed, is not sacred and is seeing plenty of experimentation with the insertion of modules. From upcoming concerts, events, suggested Pages you might like, to aggregated “most shared” content from social reader apps, plenty could start popping up between those pictures of what your friends had for lunch.  As for which friends’ lunches you see, that’s a function of the mythic EdgeRank…which is also tinkered with. When Facebook changed it in September, Page admins saw reach go down and the high anxiety set in quickly. Engagement, however, held steady. The adjustment was about relevancy over reach. (And oh yeah, reach was something that could be charged for). Facebook wants users to see what they’re most likely to like, based on past usage and interactions. Adding to the “cream must rise to the top” philosophy, they’re now even trying out ordering post comments based on the engagement the comments get. Boy, it’s getting competitive out there for a social engager. Facebook has to make $$$. To do that, they must offer attractive vehicles to marketers. There are a myriad of ad units. But a key Facebook marketing concept is the Sponsored Story. It’s key because it encourages content that’s good, relevant, and performs well organically. If it is, marketing dollars can amplify it and extend its reach. Brands can expect the rollout of a search product and an ad network. That’s a big deal. It takes, as Open Graph does, the power of Facebook’s user data and carries it beyond the Facebook environment into the digital world at large. No one could target like Facebook can, and some analysts think it could double their roughly $5 billion revenue stream. As every potential revenue nook and cranny is explored, there are the users themselves. In addition to Gifts, Facebook thinks users might pay a few bucks to promote their own posts so more of their friends will see them. There’s also word classifieds could be purchased in News Feeds, though they won’t be called classifieds. And that’s where Facebook stands; a wildly popular destination, a part of our culture, with ever increasing functionalities, the biggest of big data, revenue strategies that appeal to marketers without souring the user experience, new challenges as a now public company, ongoing privacy concerns, and innovations that carry Facebook far beyond its own borders. Anyone care to write a “this is the end of Facebook” headline? @mikestilesPhoto via stock.schng

  Read the article

• Defining Your Online Segmentation and Targeting Strategy

  - by Christie Flanagan

  Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin-top:0in; mso-para-margin-right:0in; mso-para-margin-bottom:10.0pt; mso-para-margin-left:0in; line-height:115%; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi;} A lot of times, companies will put online segmentation and targeting on the back burner because they don’t know where to start. Often, I’ve heard web managers say that their segments aren’t well understood yet, so they can’t really deliver personalized online experiences that are meaningful. This lack of complete understanding means that they don't really bother to try. But, I don’t think you necessarily need to have an elaborate segmentation and targeting strategy already in place to start delivering a more relevant online customer experience. Sometimes it helps to think of how segmentation and targeting might solve some of the challenges your sites visitors are currently experiencing on your web presence, rather than doing nothing and waiting until a fully baked segmentation strategy lands in your inbox.  For example, perhaps you have a broad and varied service offering that makes it difficult for site visitors to easily find the solutions that are most relevant for them.  How can segmentation and targeting help solve this problem?  Or maybe it’s like the airline I described in Monday’s post where the special deals featured on the home page are only relevant to site visitors from a couple of cities.  Couldn’t segmentation and targeting help them to highlight offers on their home page that are relevant to a larger share of their site visitors? Your early segmentation and targeting efforts do not need to be complicated.  There are simple ways to start delivering a more relevant online customer experience, even if you’re dealing with anonymous site visitors.  These include targeting content to site visitors based on: Referral: Deliver targeted content to your site visitors that is based on where they came from or the search term they used to find your site Behavior:  Deliver content to your site visitors that is related or similar to content they’ve clicked on already Location:  Deliver content your site visitors that is most relevant for their geographic location (this would solve that pesky airline home page problem described above) So as you can see, there really are some very simple ways in which you can start improving your online customer experience using very basic segmentation and targeting methods.  One thing to keep in mind as you start to define you segmentation and targeting strategy is that there are many different types of attributes or combinations of attributes upon which you can base your segmentation and targeting strategy.  In addition to referral, behavior and location, other attributes that you should consider are: Profile Information:  What profile information do you know about this customer already?  Perhaps they provided some information on their interests and preferences when they first registered with your site. Time:  What time is it and how does that impact what my site visitors are looking for or trying to do? Demographics: What are my site visitors’ ages, incomes or ethnicities? Which attributes you select to include in your segmentation strategy will depend on your unique business needs and objectives.  Attributes such as behavior or referral may not be the most important targeting criteria depending on your situation. For example, if you’re a newspaper you might know that certain visitors are sports fans based on their profile information.  You can create a segment for sports fans and target sports related content to that segment of your readership online.  Or perhaps, a reader is browsing stories that are related to politics; you can use that visitor’s behavior to assign him or her to a segment for those interested in politics. From there you can recommend more stories to that visitor based on their interest in politics. For an airline, the visitor’s location may be a more important attribute. By detecting the visitor’s location, you can assign them to an appropriate segment and then target special flights and offers to them based on their likely departure airport. As you can see, there are many practical ways that you can start improving the experience your customers receive on your web presence using fairly basic segmentation and targeting techniques. If you want to learn more about segmentation and targeting using Oracle’s web experience management solution, check out this helpful video that demonstrates these powerful capabilities in Oracle WebCenter Sites. ***** On Demand Webcast Featuring Brian Solis of Altimeter Group Trends such as the mobile web, social media, gamification and real-time are changing customer behavior and expectations. In this new environment, many businesses will struggle. Some will fall by the wayside, while others learn to adapt and thrive. Watch this on demand webcast with Altimeter Group digital analyst and author, Brian Solis, and discover what your organization needs to know about how to compete in the new era of Digital Darwinism. View now.

  Read the article

• IRM Item Codes &ndash; what are they for?

  - by martin.abrahams

  A number of colleagues have been asking about IRM item codes recently – what are they for, when are they useful, how can you control them to meet some customer requirements? This is quite a big topic, but this article provides a few answers. An item code is part of the metadata of every sealed document – unless you define a custom metadata model. The item code is defined when a file is sealed, and usually defaults to a timestamp/filename combination. This time/name combo tends to make item codes unique for each new document, but actually item codes are not necessarily unique, as will become clear shortly. In most scenarios, item codes are not relevant to the evaluation of a user’s rights - the context name is the critical piece of metadata, as a user typically has a role that grants access to an entire classification of information regardless of item code. This is key to the simplicity and manageability of the Oracle IRM solution. Item codes are occasionally exposed to users in the UI, but most users probably never notice and never care. Nevertheless, here is one example of where you can see an item code – when you hover the mouse pointer over a sealed file. As you see, the item code for this freshly created file combines a timestamp with the file name. But what are item codes for? The first benefit of item codes is that they enable you to manage exceptions to the policy defined for a context. Thus, I might have access to all oracle – internal files - except for 2011_03_11 13:33:29 Board Minutes.sdocx. This simple mechanism enables Oracle IRM to provide file-by-file control where appropriate, whilst offering the scalability and manageability of classification-based control for the majority of users and content. You really don’t want to be managing each file individually, but never say never. Item codes can also be used for the opposite effect – to include a file in a user’s rights when their role would ordinarily deny access. So, you can assign a role that allows access only to specified item codes. For example, my role might say that I have access to precisely one file – the one shown above. So how are item codes set? In the vast majority of scenarios, item codes are set automatically as part of the sealing process. The sealing API uses the timestamp and filename as shown, and the user need not even realise that this has happened. This automatically creates item codes that are for all practical purposes unique - and that are also intelligible to users who might want to refer to them when viewing or assigning rights in the management UI. It is also possible for suitably authorised users and applications to set the item code manually or programmatically if required. Setting the item code manually using the IRM Desktop The manual process is a simple extension of the sealing task. An authorised user can select the Advanced… sealing option, and will see a dialog that offers the option to specify the item code. To see this option, the user’s role needs the Set Item Code right – you don’t want most users to give any thought at all to item codes, so by default the option is hidden. Setting the item code programmatically A more common scenario is that an application controls the item code programmatically. For example, a document management system that seals documents as part of a workflow might set the item code to match the document’s unique identifier in its repository. This offers the option to tie IRM rights evaluation directly to the security model defined in the document management system. Again, the sealing application needs to be authorised to Set Item Code. The Payslip Scenario To give a concrete example of how item codes might be used in a real world scenario, consider a Human Resources workflow such as a payslips. The goal might be to allow the HR team to have access to all payslips, but each employee to have access only to their own payslips. To enable this, you might have an IRM classification called Payslips. The HR team have a role in the normal way that allows access to all payslips. However, each employee would have an Item Reader role that only allows them to access files that have a particular item code – and that item code might match the employee’s payroll number. So, employee number 123123123 would have access to items with that code. This shows why item codes are not necessarily unique – you can deliberately set the same code on many files for ease of administration. The employees might have the right to unseal or print their payslip, so the solution acts as a secure delivery mechanism that allows payslips to be distributed via corporate email without any fear that they might be accessed by IT administrators, or forwarded accidentally to anyone other than the intended recipient. All that remains is to ensure that as each user’s payslip is sealed, it is assigned the correct item code – something that is easily managed by a simple IRM sealing application. Each month, an employee’s payslip is sealed with the same item code, so you do not need to keep amending the list of items that the user has access to – they have access to all documents that carry their employee code.

  Read the article

• June is going to be a busy month!

  - by Monica Kumar

  Who says things slow down in summer? Well, maybe for school kids, but certainly not for Oracle's Virtualization team! June is turning out to be one of the busiest months for us. We are going to be participating in a number of industry events. If you happen to be at any of these, please stop by the Oracle booth and our session/s. Let's go through a run down of these events. 1. 13th Annual Call Center Week June 4-8 Ceasar's Palace, Las Vegas  Event website You're now wondering...why are we at this call center show. It's really simple, Oracle's Desktop Virtualization solutions offer the best way for call center to reliably and securely access enterprise apps using a variety of endpoint devices such as an iPad or a Sun Ray Client. Provisioning new employees becomes a breeze. We'll be jointly showcasing our solution with Oracle's CRM team. Come check us out.  2. Gartner Infrastructure & Management, Florida June 5-7 Orlando, FL  Event website Oracle is a Premier sponsor of the Gartner IOM Summit this June 5 – 7, 2012 in Orlando, FL.  Attendees will have the opportunity to meet with Oracle experts in a variety of sessions, including demonstrations during the showcase receptions. 3. Cloud Expo East Check out our website for details of our participation. Stop by at booth 511 to talk to our Cloud, Virtualization and Big Data experts. In addition, we're delivering a number of sessions at Cloud Expo. The one I want to highlight is the following: Session: Borderless Applications in the Cloud with Oracle VM and Oracle Virtual Assembly Builder Abstract: As virtualization adoption progresses beyond server consolidation, this is also transforming how enterprise applications are deployed and managed in an agile environment. The traditional method of business-critical application deployment where administrators have to contend with an array of unrelated tools, custom scripts to deploy and manage applications, OS and VM instances into a fast changing cloud computing environment can no longer scale effectively to achieve response time and desired efficiency. Oracle VM and Oracle Virtual Assembly Builder allow applications, associated components, deployment metadata, management policies and best practices to be encapsulated into ready-to-run VMs for rapid, repeatable deployment and ease of management. Join us in this Cloud Expo session to see how Oracle VM and Oracle Virtual Assembly Builder allow you to deploy complex multi-tier applications in minutes and enables you to easily onboard existing applications to cloud environments.  Get your free Cloud Expo pass now!  We're offering complimentary VIP Gold Passes. Go to https://www.blueskyz.com/v3/Login.aspx?ClientID=19&EventID=56&sg=177, click “Continue” if you are a New User or log-in if you have already created an account. Once there, you can view the Agenda or Register for Cloud Expo. To register - fill out the basic business card questions and then enter oracleVIPgold in the Priority Code field to change the price from $2,000 to $0. 4. CiscoLive 2012  June 10-14 San Diego, CA Event website Our Oracle VM and Oracle Linux experts will talk about joint collaboration with Cisco on UCS. We'll also highlight customer use cases. 5. Gartner Infrastructure & Operations Management Summit, EMEA Dates: June 11-12 Frankfurt, Germany Event website Meet experts from our Virtualization and Linux team in EMEA. Stop by our booth and find out what's new in Oracle VM Server for x86 and Oracle Linux. June is going to be busy.

  Read the article

• SEASON'S GREETINGS AND HAPPY HOLIDAYS

  - by klaudia.drulis

  p.msonormal { margin:0in; margin-bottom:.0001pt; font-size:11.0pt; font-family:calibri; } li.msonormal { margin:0in; margin-bottom:.0001pt; font-size:11.0pt; font-family:calibri; } p.listparagraph { margin-top:0in; margin-right:0in; margin-bottom:.0001pt; margin-left:.5in; font-size:11.0pt; font-family:calibri; } -- ! Please follow Guidelines for a proper working email ! ___________________________________________________________________________________________________________________ Oracle standard tags   symbol entity Special character Ampersand & & Apostrophe ’ ’ Copyright © © Ellipsis … … Em dash — — En dash – – Euro € € Pound £ £ Left quote “ “ Right quote ” ” Registered trademark ® ® Trademark ™ ℄ Yen ¥ ¥ ___________________________________________________________________________________________________________________ IMPORTANT in creating a link to have a desired color (red, black, etc) that will work in Hotmail, Yahoo, Outlook, and Gmail You MUST Place the inside the Example Click Here The order you must follow to make the colored link appear in browsers. If not the default window link will appear 1. Select the word you want to use for the link 2. Select the desired color, Red, Black, etc 3. Select bold if necessary ___________________________________________________________________________________________________________________ Templates use two sizes of fonts and the sans-serif font tag for the email. All Fonts should be (Arial, Helvetica, sans-serif) tags Normal size reading body fonts should be set to the size of 2. Small font sizes should be set to 1 !!!!!!!DO NOT USE ANY OTHER SIZE FONT FOR THE EMAILS!!!!!!!! ___________________________________________________________________________________________________________________ --   SEASON'S GREETINGS AND HAPPY HOLIDAYS Click here to view the e-card We would like to wish you a Merry Christmas and a prosperous new year. Tanti auguri di buon natale e felice anno nuovo!!! Je vous souhaite de joyeuses fetes, et tous mes voeux de succes pour l'annee a venir ! Tous mes voeux de bonheur, de succes et d’epanouissement pour 2011! Va urez Sarbatori Fericite si un an nou fericit!!! El equipo de Recruitment de Oracle te desea una feliz navidad y un fantastico 2011 Namens het campus recruitment team wensen wij je fijne feestdagen en een uitdagend 2011! In this closing paragraph, reinforce the primary benefit or opportunity being offered. Include a call to action and contact information. Body copy to this point should not exceed 150 words. Wszystkim Sympatykom naszego Blogu skladamy zyczenia Spokojnych i Radosnych Swiat Bozego Narodzenia oraz Pomyslnosci i Sukcesów w Nowym Roku.     Stay Connected: Facebook Experienced YouTube Twitter OracleMix Graduates Copyright © 2010, Oracle and/or its affiliates. All rights reserved.    

  Read the article

• What Keeps You from Changing Your Public IP Address and Wreaking Havoc on the Internet?

  - by Jason Fitzpatrick

  What exactly is preventing you (or anyone else) from changing their IP address and causing all sorts of headaches for ISPs and other Internet users? Today’s Question & Answer session comes to us courtesy of SuperUser—a subdivision of Stack Exchange, a community-driven grouping of Q&A web sites. The Question SuperUser reader Whitemage is curious about what’s preventing him from wantonly changing his IP address and causing trouble: An interesting question was asked of me and I did not know what to answer. So I’ll ask here. Let’s say I subscribed to an ISP and I’m using cable internet access. The ISP gives me a public IP address of 60.61.62.63. What keeps me from changing this IP address to, let’s say, 60.61.62.75, and messing with another consumer’s internet access? For the sake of this argument, let’s say that this other IP address is also owned by the same ISP. Also, let’s assume that it’s possible for me to go into the cable modem settings and manually change the IP address. Under a business contract where you are allocated static addresses, you are also assigned a default gateway, a network address and a broadcast address. So that’s 3 addresses the ISP “loses” to you. That seems very wasteful for dynamically assigned IP addresses, which the majority of customers are. Could they simply be using static arps? ACLs? Other simple mechanisms? Two things to investigate here, why can’t we just go around changing our addresses, and is the assignment process as wasteful as it seems? The Answer SuperUser contributor Moses offers some insight: Cable modems aren’t like your home router (ie. they don’t have a web interface with simple point-and-click buttons that any kid can “hack” into). Cable modems are “looked up” and located by their MAC address by the ISP, and are typically accessed by technicians using proprietary software that only they have access to, that only runs on their servers, and therefore can’t really be stolen. Cable modems also authenticate and cross-check settings with the ISPs servers. The server has to tell the modem whether it’s settings (and location on the cable network) are valid, and simply sets it to what the ISP has it set it for (bandwidth, DHCP allocations, etc). For instance, when you tell your ISP “I would like a static IP, please.”, they allocate one to the modem through their servers, and the modem allows you to use that IP. Same with bandwidth changes, for instance. To do what you are suggesting, you would likely have to break into the servers at the ISP and change what it has set up for your modem. Could they simply be using static arps? ACLs? Other simple mechanisms? Every ISP is different, both in practice and how close they are with the larger network that is providing service to them. Depending on those factors, they could be using a combination of ACL and static ARP. It also depends on the technology in the cable network itself. The ISP I worked for used some form of ACL, but that knowledge was a little beyond my paygrade. I only got to work with the technician’s interface and do routine maintenance and service changes. What keeps me from changing this IP address to, let’s say, 60.61.62.75 and mess with another consumer’s internet access? Given the above, what keeps you from changing your IP to one that your ISP hasn’t specifically given to you is a server that is instructing your modem what it can and can’t do. Even if you somehow broke into the modem, if 60.61.62.75 is already allocated to another customer, then the server will simply tell your modem that it can’t have it. David Schwartz offers some additional insight with a link to a white paper for the really curious: Most modern ISPs (last 13 years or so) will not accept traffic from a customer connection with a source IP address they would not route to that customer were it the destination IP address. This is called “reverse path forwarding”. See BCP 38. Have something to add to the explanation? Sound off in the the comments. Want to read more answers from other tech-savvy Stack Exchange users? Check out the full discussion thread here.     

  Read the article

• Coping with infrastructure upgrades

  - by Fatherjack

  A common topic for questions on SQL Server forums is how to plan and implement upgrades to SQL Server. Moving from old to new hardware or moving from one version of SQL Server to another. There are other circumstances where upgrades of other systems affect SQL Server DBAs. For example, where I work at the moment there is an Microsoft Exchange (email) server upgrade in progress. It it being handled by a different team so I’m not wholly sure on the details but we are in a situation where there are currently 2 Exchange email servers – the old one and the new one. Users mail boxes are being transferred in a planned process but as we approach the old server being turned off we have to also make sure that our SQL Servers get updated to use the new SMTP server for all of the SQL Agent notifications, SSIS packages etc. My servers have a number of profiles so that various jobs can send emails on behalf of various departments and different systems. This means there are lots of places that the old server name needs to be replaced by the new one. Anyone who has set up DBMail and enjoyed the click-tastic odyssey of screens to create Profiles and Accounts and so on and so forth ought to seek some professional help in my opinion. It’s a nightmare of back and forth settings changes and it stinks. I wasn’t looking forward to heading into this mess of a UI and changing the old Exchange server name for the new one on all my SQL Instances for all of the accounts I have set up. So I did what any Englishmen with a shed would do, I decided to take it apart and see if I can fix it another way. I took a guess that we are going to be working in MSDB and Books OnLine was remarkably helpful and amongst a lot of information told me about a couple of procedures that can be used to interrogate DBMail settings. USE [msdb] -- It's where all the good stuff is kept GO EXEC dbo.sysmail_help_profile_sp; EXEC dbo.sysmail_help_account_sp; Both of these procedures take optional parameters with the same name – ID and Name. If you provide an ID or a name then the results you get back are for that specific Profile or Account. Otherwise you get details of all Profiles and Accounts on the server you are connected to. As you can see (click for a bigger image), the Account has the SMTP server information in the servername column. We want to change that value to NewSMTP.Contoso.com. Now it appears that the procedure we are looking at gets it’s data from the sysmail_account and sysmail_server tables, you can get the results the stored procedure provides if you run the code below. SELECT [account_id] , [name] , [description] , [email_address] , [display_name] , [replyto_address] , [last_mod_datetime] , [last_mod_user] FROM dbo.sysmail_account AS sa; SELECT [account_id] , [servertype] , [servername] , [port] , [username] , [credential_id] , [use_default_credentials] , [enable_ssl] , [flags] , [last_mod_datetime] , [last_mod_user] , [timeout] FROM dbo.sysmail_server AS sms Now, we have no real idea how these tables are linked and whether making an update direct to one or other of them is going to do what we want or whether it will entirely cripple our ability to send email from SQL Server so we wont touch those tables with any UPDATE TSQL. So, back to Books OnLine then and we find sysmail_update_account_sp. It’s exactly what we need. The examples in BOL take the form (as below) of having every parameter explicitly defined. Not wanting to totally obliterate the existing values by not passing values in all of the parameters I set to writing some code to gather the existing data from the tables and re-write the SMTP server name and then execute the resulting TSQL. IF OBJECT_ID('tempdb..#sysmailprofiles') IS NOT NULL DROP TABLE #sysmailprofiles GO CREATE TABLE #sysmailprofiles ( account_id INT , [name] VARCHAR(50) , [description] VARCHAR(500) , email_address VARCHAR(500) , display_name VARCHAR(500) , replyto_address VARCHAR(500) , servertype VARCHAR(10) , servername VARCHAR(100) , port INT , username VARCHAR(100) , use_default_credentials VARCHAR(1) , ENABLE_ssl VARCHAR(1) ) INSERT [#sysmailprofiles] ( [account_id] , [name] , [description] , [email_address] , [display_name] , [replyto_address] , [servertype] , [servername] , [port] , [username] , [use_default_credentials] , [ENABLE_ssl] ) EXEC [dbo].[sysmail_help_account_sp] DECLARE @TSQL NVARCHAR(1000) SELECT TOP 1 @TSQL = 'EXEC [dbo].[sysmail_update_account_sp] @account_id = ' + CAST([s].[account_id] AS VARCHAR(20)) + ', @account_name = ''' + [s].[name] + '''' + ', @email_address = N''' + [s].[email_address] + '''' + ', @display_name = N''' + [s].[display_name] + '''' + ', @replyto_address = N''' + s.replyto_address + '''' + ', @description = N''' + [s].[description] + '''' + ', @mailserver_name = ''NEWSMTP.contoso.com''' + +', @mailserver_type = ' + [s].[servertype] + ', @port = ' + CAST([s].[port] AS VARCHAR(20)) + ', @username = ' + COALESCE([s].[username], '''''') + ', @use_default_credentials =' + CAST(s.[use_default_credentials] AS VARCHAR(1)) + ', @enable_ssl =' + [s].[ENABLE_ssl] FROM [#sysmailprofiles] AS s WHERE [s].[servername] = 'SMTP.Contoso.com' SELECT @tsql EXEC [sys].[sp_executesql] @tsql This worked well for me and testing the email function EXEC dbo.sp_send_dbmail afterwards showed that the settings were indeed using our new Exchange server. It was only later in writing this blog that I tried running the sysmail_update_account_sp procedure with only the SMTP server name parameter value specified. Despite what Books OnLine might intimate, you can do this and only the values for parameters specified get changed. If a parameter is not specified in the execution of the procedure then the values remain unchanged. This renders most of the above script unnecessary as I could have simply specified the account_id that I want to amend and the new value for the parameter I want to update. EXEC sysmail_update_account_sp @account_id = 1, @mailserver_name = 'NEWSMTP.Contoso.com' This wasn’t going to be the main reason for this post, it was meant to describe how to capture values from a stored procedure and use them in dynamic TSQL but instead we are here and (re)learning the fact that Books Online is a little flawed in places. It is a fantastic resource for anyone working with SQL Server but the reader must adopt an enquiring frame of mind and use a little curiosity to try simple variations on examples to fully understand the code you are working with. I think the author(s) of this part of Books OnLine missed an opportunity to include a third example that had fewer than all parameters specified to give a lead to this method existing.

  Read the article

• Can not print after upgrading from 12.x to 14.04

  - by user318889

  After upgrading from V12.04 to V14.04 I am not able to print. I am using an HP LaserJet 400 M451dn. The printer troubleshooter told me that there is no solution to the problem. This is the output of the advanced diagnositc output. (Due to limited space I cut the output!) Can anybody tell me what is going wrong. I am using the printer via USB ? Page 1 (Scheduler not running?): {'cups_connection_failure': False} Page 2 (Is local server publishing?): {'local_server_exporting_printers': False} Page 3 (Choose printer): {'cups_dest': , 'cups_instance': None, 'cups_queue': u'HP-LaserJet-400-color-M451dn', 'cups_queue_listed': True} Page 4 (Check printer sanity): {'cups_device_uri_scheme': u'hp', 'cups_printer_dict': {'device-uri': u'hp:/usb/HP_LaserJet_400_color_M451dn?serial=CNFF308670', 'printer-info': u'Hewlett-Packard HP LaserJet 400 color M451dn', 'printer-is-shared': True, 'printer-location': u'Pinatubo', 'printer-make-and-model': u'HP LJ 300-400 color M351-M451 Postscript (recommended)', 'printer-state': 4, 'printer-state-message': u'', 'printer-state-reasons': [u'none'], 'printer-type': 8556636, 'printer-uri-supported': u'ipp://localhost:631/printers/HP-LaserJet-400-color-M451dn'}, 'cups_printer_remote': False, 'hplip_output': (['', '\x1b[01mHP Linux Imaging and Printing System (ver. 3.14.6)\x1b[0m', '\x1b[01mDevice Information Utility ver. 5.2\x1b[0m', '', 'Copyright (c) 2001-13 Hewlett-Packard Development Company, LP', 'This software comes with ABSOLUTELY NO WARRANTY.', 'This is free software, and you are welcome to distribute it', 'under certain conditions. See COPYING file for more details.', '', '', '\x1b[01mhp:/usb/HP_LaserJet_400_color_M451dn?serial=CNFF308670\x1b[0m', '', '\x1b[01mDevice Parameters (dynamic data):\x1b[0m', '\x1b[01m Parameter Value(s) \x1b[0m', ' ---------------------------- ----------------------------------------------------------', ' back-end hp ', " cups-printers ['HP-LaserJet-400-color-M451dn'] ", ' cups-uri hp:/usb/HP_LaserJet_400_color_M451dn?serial=CNFF308670 ', ' dev-file ', ' device-state -1 ', ' device-uri hp:/usb/HP_LaserJet_400_color_M451dn?serial=CNFF308670 ', ' deviceid ', ' error-state 101 ', ' host ', ' is-hp True ', ' panel 0 ', ' panel-line1 ', ' panel-line2 ', ' port 1 ', ' serial CNFF308670 ', ' status-code 5002 ', ' status-desc ', '\x1b[01m', 'Model Parameters (static data):\x1b[0m', '\x1b[01m Parameter Value(s) \x1b[0m', ' ---------------------------- ----------------------------------------------------------', ' align-type 0 ', ' clean-type 0 ', ' color-cal-type 0 ', ' copy-type 0 ', ' embedded-server-type 0 ', ' fax-type 0 ', ' fw-download False ', ' icon hp_color_laserjet_cp2025.png ', ' io-mfp-mode 1 ', ' io-mode 1 ', ' io-support 6 ', ' job-storage 0 ', ' linefeed-cal-type 0 ', ' model HP_LaserJet_400_color_M451dn ', ' model-ui HP LaserJet 400 Color m451dn ', ' model1 HP LaserJet 400 Color M451dn ', ' monitor-type 0 ', ' panel-check-type 0 ', ' pcard-type 0 ', ' plugin 0 ', ' plugin-reason 0 ', ' power-settings 0 ', ' ppd-name lj_300_400_color_m351_m451 ', ' pq-diag-type 0 ', ' r-type 0 ', ' r0-agent1-kind 4 ', ' r0-agent1-sku CE410A/CE410X ', ' r0-agent1-type 1 ', ' r0-agent2-kind 4 ', ' r0-agent2-sku CE411A ', ' r0-agent2-type 4 ', ' r0-agent3-kind 4 ', ' r0-agent3-sku CE413A ', ' r0-agent3-type 5 ', ' r0-agent4-kind 4 ', ' r0-agent4-sku CE412A ', ' r0-agent4-type 6 ', ' scan-src 0 ', ' scan-type 0 ', ' status-battery-check 0 ', ' status-dynamic-counters 0 ', ' status-type 3 ', ' support-released True ', ' support-subtype 2202411 ', ' support-type 2 ', ' support-ver 3.12.2 ', " tech-class ['Postscript'] ", " tech-subclass ['Normal'] ", ' tech-type 4 ', ' usb-pid 3882 ', ' usb-vid 1008 ', ' wifi-config 0 ', '\x1b[01m', 'Status History (most recent first):\x1b[0m', '\x1b[01m Date/Time Code Status Description User Job ID \x1b[0m', ' -------------------- ----- ---------------------------------------- -------- --------', ' 08/21/14 00:07:25 5012 Device communication error richard 0 ', ' 08/20/14 13:42:44 500 Started a print job richard 4214 ', '', '', 'Done.', ''], ['\x1b[35;01mwarning: No display found.\x1b[0m', '\x1b[31;01merror: hp-info -u/--gui requires Qt4 GUI support. Entering interactive mode.\x1b[0m', '\x1b[31;01merror: Unable to communicate with device (code=12): hp:/usb/HP_LaserJet_400_color_M451dn?serial=CNFF308670\x1b[0m', '\x1b[31;01merror: Error opening device (Device not found).\x1b[0m', ''], 0), 'is_cups_class': False, 'local_cups_queue_attributes': {'charset-configured': u'utf-8', 'charset-supported': [u'us-ascii', u'utf-8'], 'color-supported': True, 'compression-supported': [u'none', u'gzip'], 'copies-default': 1, 'copies-supported': (1, 9999), 'cups-version': u'1.7.2', 'device-uri': u'hp:/usb/HP_LaserJet_400_color_M451dn?serial=CNFF308670', 'document-format-default': u'application/octet-stream', 'document-format-supported': [u'application/octet-stream', u'application/pdf', u'application/postscript', u'application/vnd.adobe-reader-postscript', u'application/vnd.cups-command', u'application/vnd.cups-pdf', u'application/vnd.cups-pdf-banner', u'application/vnd.cups-postscript', u'application/vnd.cups-raw', u'application/vnd.samsung-ps', u'application/x-cshell', u'application/x-csource', u'application/x-perl', u'application/x-shell', u'image/gif', u'image/jpeg', u'image/png', u'image/tiff', u'image/urf', u'image/x-bitmap', u'image/x-photocd', u'image/x-portable-anymap', u'image/x-portable-bitmap', u'image/x-portable-graymap', u'image/x-portable-pixmap', u'image/x-sgi-rgb', u'image/x-sun-raster', u'image/x-xbitmap', u'image/x-xpixmap', u'image/x-xwindowdump', u'text/css', u'text/html', u'text/plain'], 'finishings-default': 3, 'finishings-supported': [3], 'generated-natural-language-supported': [u'en-us'], 'ipp-versions-supported': [u'1.0', u'1.1', u'2.0', u'2.1'], 'ippget-event-life': 15, 'job-creation-attributes-supported': [u'copies', u'finishings', u'ipp-attribute-fidelity', u'job-hold-until', u'job-name', u'job-priority', u'job-sheets', u'media', u'media-col', u'multiple-document-handling', u'number-up', u'output-bin', u'orientation-requested', u'page-ranges', u'print-color-mode', u'print-quality', u'printer-resolution', u'sides'], 'job-hold-until-default': u'no-hold', 'job-hold-until-supported': [u'no-hold', u'indefinite', u'day-time', u'evening', u'night', u'second-shift', u'third-shift', u'weekend'], 'job-ids-supported': True, 'job-k-limit': 0, 'job-k-octets-supported': (0, 470914416), 'job-page-limit': 0, 'job-priority-default': 50, 'job-priority-supported': [100], 'job-quota-period': 0, 'job-settable-attributes-supported': [u'copies', u'finishings', u'job-hold-until', u'job-name', u'job-priority', u'media', u'media-col', u'multiple-document-handling', u'number-up', u'output-bin', u'orientation-requested', u'page-ranges', u'print-color-mode', u'print-quality', u'printer-resolution', u'sides'], 'job-sheets-default': (u'none', u'none'), 'job-sheets-supported': [u'none', u'classified', u'confidential', u'form', u'secret', u'standard', u'topsecret', u'unclassified'], 'jpeg-k-octets-supported': (0, 470914416), 'jpeg-x-dimension-supported': (0, 65535), 'jpeg-y-dimension-supported': (1, 65535), 'marker-change-time': 0, 'media-bottom-margin-supported': [423], 'media-col-default': u'(unknown IPP value tag 0x34)', 'media-col-supported': [u'media-bottom-margin', u'media-left-margin', u'media-right-margin', u'media-size', u'media-source', u'media-top-margin', u'media-type'], 'media-default': u'iso_a4_210x297mm', 'media-left-margin-supported': [423], 'media-right-margin-supported': [423],

  Read the article

• How can I read kindle book under xfce(ubuntu)? (using chromebook)(wine not working)

  - by yshn

  I'm using chromebook, dual booting xfce(ubuntu) and cr os. The ebook I bought on amazon is not supported on kindle cloud reader. (Under xfce)I downloaded wine and tried installing kindle for pc under wine, and after couples of times of trials, it always said installation error and could not install kindle, and it's been giving me: Unhandled exception: unimplemented function msvcp90.dll.??0?$basic_ofstream@DU?$char_traits@D@std@@@std@@QAE@XZ called in 32-bit code (0x7b839cf2). Register dump: CS:0023 SS:002b DS:002b ES:002b FS:0063 GS:006b EIP:7b839cf2 ESP:0033fcd4 EBP:0033fd38 EFLAGS:00000287( - -- I S - -P-C) EAX:7b826245 EBX:7b894ff4 ECX:00000008 EDX:0033fcf4 ESI:80000100 EDI:00dca568 Stack dump: 0x0033fcd4: 0033fd58 00000008 00000030 80000100 0x0033fce4: 00000001 00000000 7b839cf2 00000002 0x0033fcf4: 7e24b340 7e24f2ca 0000000d 00110000 0x0033fd04: 7bc47a0d 7e1dbff4 7e1417f0 00dca568 0x0033fd14: 0033fd24 7bc65d0b 00110000 00000000 0x0033fd24: 0033fd44 7e141801 7b839caa 7e1dbff4 000c: sel=0067 base=00000000 limit=00000000 16-bit r-x Backtrace: =0 0x7b839cf2 in kernel32 (+0x29cf2) (0x0033fd38) 1 0x7e24b2a8 in msvcp90 (+0x3b2a7) (0x0033fd68) 2 0x7e216c9d in msvcp90 (+0x6c9c) (0x0033fde8) 3 0x00938fdd in kindle (+0x538fdc) (0x0033fde8) 4 0x0089dc71 in kindle (+0x49dc70) (0x0033fe70) 5 0x7b859cdc call_process_entry+0xb() in kernel32 (0x0033fe88) 6 0x7b85af4f in kernel32 (+0x4af4e) (0x0033fec8) 7 0x7bc71db0 call_thread_func_wrapper+0xb() in ntdll (0x0033fed8) 8 0x7bc7486d call_thread_func+0x7c() in ntdll (0x0033ffa8) 9 0x7bc71d8e RtlRaiseException+0x21() in ntdll (0x0033ffc8) 10 0x7bc49f4e call_dll_entry_point+0x61d() in ntdll (0x0033ffe8) 0x7b839cf2: subl $4,%esp Modules: Module Address Debug info Name (130 modules) PE 340000- 37d000 Deferred ssleay32 PE 390000- 3ca000 Deferred webcoreviewer PE 3d0000- 3e0000 Deferred pthreadvc2 PE 400000- 1433000 Export kindle PE 1440000- 155c000 Deferred libeay32 PE 1560000- 169f000 Deferred qtscript4 PE 16a0000- 1795000 Deferred libxml2 PE 17a0000- 18c7000 Deferred javascriptcore PE 18d0000- 1974000 Deferred cflite PE 1980000- 2048000 Deferred libwebcore PE 2050000- 208d000 Deferred libjpeg PE 10000000-10a34000 Deferred qtwebkit4 PE 4a800000-4a8eb000 Deferred icuuc46 PE 4a900000-4aa36000 Deferred icuin46 PE 4ad00000-4bb80000 Deferred icudt46 PE 5a4c0000-5a4d4000 Deferred zlib1 PE 61000000-61056000 Deferred qtxml4 PE 62000000-62093000 Deferred qtsql4 PE 64000000-640ef000 Deferred qtnetwork4 PE 65000000-657b8000 Deferred qtgui4 PE 67000000-67228000 Deferred qtcore4 PE 78050000-780b9000 Deferred msvcp100 PE 78aa0000-78b5e000 Deferred msvcr100 ELF 7b800000-7ba15000 Dwarf kernel32 -PE 7b810000-7ba15000 \ kernel32 ELF 7bc00000-7bcc3000 Dwarf ntdll -PE 7bc10000-7bcc3000 \ ntdll ELF 7bf00000-7bf04000 Deferred ELF 7d7f7000-7d800000 Deferred librt.so.1 ELF 7d800000-7d818000 Deferred libresolv.so.2 ELF 7d818000-7d861000 Deferred libdbus-1.so.3 ELF 7d861000-7d873000 Deferred libp11-kit.so.0 ELF 7d873000-7d8f8000 Deferred libgcrypt.so.11 ELF 7d8f8000-7d90a000 Deferred libtasn1.so.3 ELF 7d90a000-7d913000 Deferred libkrb5support.so.0 ELF 7d913000-7d9e2000 Deferred libkrb5.so.3 ELF 7da42000-7da47000 Deferred libgpg-error.so.0 ELF 7da47000-7da6f000 Deferred libk5crypto.so.3 ELF 7da6f000-7da81000 Deferred libavahi-client.so.3 ELF 7da81000-7da8f000 Deferred libavahi-common.so.3 ELF 7da8f000-7db53000 Deferred libgnutls.so.26 ELF 7db53000-7db91000 Deferred libgssapi_krb5.so.2 ELF 7db91000-7dbe4000 Deferred libcups.so.2 ELF 7dc21000-7dc55000 Deferred uxtheme -PE 7dc30000-7dc55000 \ uxtheme ELF 7dc55000-7dc5b000 Deferred libxfixes.so.3 ELF 7dc5b000-7dc66000 Deferred libxcursor.so.1 ELF 7dc6a000-7dc6e000 Deferred libkeyutils.so.1 ELF 7dc6e000-7dc73000 Deferred libcom_err.so.2 ELF 7dca5000-7dccf000 Deferred libexpat.so.1 ELF 7dccf000-7dd03000 Deferred libfontconfig.so.1 ELF 7dd03000-7dd13000 Deferred libxi.so.6 ELF 7dd13000-7dd17000 Deferred libxcomposite.so.1 ELF 7dd17000-7dd20000 Deferred libxrandr.so.2 ELF 7dd20000-7dd2a000 Deferred libxrender.so.1 ELF 7dd2a000-7dd30000 Deferred libxxf86vm.so.1 ELF 7dd30000-7dd34000 Deferred libxinerama.so.1 ELF 7dd34000-7dd3b000 Deferred libxdmcp.so.6 ELF 7dd3b000-7dd5c000 Deferred libxcb.so.1 ELF 7dd5c000-7dd76000 Deferred libice.so.6 ELF 7dd76000-7deaa000 Deferred libx11.so.6 ELF 7deaa000-7debc000 Deferred libxext.so.6 ELF 7debc000-7dec5000 Deferred libsm.so.6 ELF 7ded4000-7df67000 Deferred winex11 -PE 7dee0000-7df67000 \ winex11 ELF 7df67000-7e001000 Deferred libfreetype.so.6 ELF 7e001000-7e023000 Deferred iphlpapi -PE 7e010000-7e023000 \ iphlpapi ELF 7e023000-7e03e000 Deferred wsock32 -PE 7e030000-7e03e000 \ wsock32 ELF 7e03e000-7e071000 Deferred wintrust -PE 7e040000-7e071000 \ wintrust ELF 7e071000-7e129000 Deferred crypt32 -PE 7e080000-7e129000 \ crypt32 ELF 7e129000-7e158000 Deferred msvcr90 -PE 7e130000-7e158000 \ msvcr90 ELF 7e158000-7e1e5000 Deferred msvcrt -PE 7e170000-7e1e5000 \ msvcrt ELF 7e1e5000-7e2ca000 Dwarf msvcp90 -PE 7e210000-7e2ca000 \ msvcp90 ELF 7e2ca000-7e2ec000 Deferred imm32 -PE 7e2d0000-7e2ec000 \ imm32 ELF 7e2ec000-7e3de000 Deferred oleaut32 -PE 7e300000-7e3de000 \ oleaut32 ELF 7e3de000-7e418000 Deferred winspool -PE 7e3f0000-7e418000 \ winspool ELF 7e418000-7e4f7000 Deferred comdlg32 -PE 7e420000-7e4f7000 \ comdlg32 ELF 7e4f7000-7e51f000 Deferred msacm32 -PE 7e500000-7e51f000 \ msacm32 ELF 7e51f000-7e5cc000 Deferred winmm -PE 7e530000-7e5cc000 \ winmm ELF 7e5cc000-7e641000 Deferred rpcrt4 -PE 7e5e0000-7e641000 \ rpcrt4 ELF 7e641000-7e749000 Deferred ole32 -PE 7e660000-7e749000 \ ole32 ELF 7e749000-7e841000 Deferred comctl32 -PE 7e750000-7e841000 \ comctl32 ELF 7e841000-7ea52000 Deferred shell32 -PE 7e850000-7ea52000 \ shell32 ELF 7ea52000-7eabc000 Deferred shlwapi -PE 7ea60000-7eabc000 \ shlwapi ELF 7eabc000-7ead5000 Deferred version -PE 7eac0000-7ead5000 \ version ELF 7ead5000-7eb35000 Deferred advapi32 -PE 7eae0000-7eb35000 \ advapi32 ELF 7eb35000-7ebf2000 Deferred gdi32 -PE 7eb40000-7ebf2000 \ gdi32 ELF 7ebf2000-7ed32000 Deferred user32 -PE 7ec00000-7ed32000 \ user32 ELF 7ed32000-7ed58000 Deferred mpr -PE 7ed40000-7ed58000 \ mpr ELF 7ed58000-7ed6e000 Deferred libz.so.1 ELF 7ed6e000-7eddd000 Deferred wininet -PE 7ed80000-7eddd000 \ wininet ELF 7eddd000-7ee0f000 Deferred ws2_32 -PE 7ede0000-7ee0f000 \ ws2_32 ELF 7ee0f000-7ee1c000 Deferred libnss_files.so.2 ELF 7ee1c000-7ee28000 Deferred libnss_nis.so.2 ELF 7ee28000-7ee42000 Deferred libnsl.so.1 ELF 7ee42000-7ee4b000 Deferred libnss_compat.so.2 ELF 7efd4000-7f000000 Deferred libm.so.6 ELF f74a3000-f74a7000 Deferred libxau.so.6 ELF f74a8000-f74ad000 Deferred libdl.so.2 ELF f74ad000-f7657000 Deferred libc.so.6 ELF f7658000-f7673000 Deferred libpthread.so.0 ELF f7675000-f767b000 Deferred libuuid.so.1 ELF f7682000-f77c4000 Dwarf libwine.so.1 ELF f77c6000-f77e8000 Deferred ld-linux.so.2 ELF f77e8000-f77e9000 Deferred [vdso].so Threads: process tid prio (all id:s are in hex) 0000000e services.exe 0000001f 0 0000001e 0 00000015 0 00000010 0 0000000f 0 00000012 winedevice.exe 0000001c 0 00000019 0 00000014 0 00000013 0 0000001a plugplay.exe 00000020 0 0000001d 0 0000001b 0 00000037 explorer.exe 00000038 0 00000042 (D) C:\Program Files (x86)\Amazon\Kindle\Kindle.exe 00000043 0 <== System information: Wine build: wine-1.4 Platform: i386 (WOW64) Host system: Linux Host version: 3.8.11 How can this be fixed?

  Read the article

• VirtualBox Clone Root HD / Ubuntu / Network issue

  - by john.graves(at)oracle.com

  When you clone a root Ubuntu disk in VirtualBox, one thing that gets messed up is the network card definition.  This is because Ubuntu (as it should) uses UDEV IDs for the network device.  When you boot your new disk, the network device ID has changed, so it creates a new eth1 device.  Unfortunately, this conflicts with the VirtualBox network setup.  What to do? Boot the box (no network) Edit the /etc/udev/rules.d/70-persistent-net.rules Delete the eth0 line and modify the eth1 line to be eth0 --------- Example OLD ----------- # This file was automatically generated by the /lib/udev/write_net_rules # program, run by the persistent-net-generator.rules rules file. # # You can modify it, as long as you keep each rule on a single # line, and change only the value of the NAME= key. # PCI device 0x8086:0x100e (e1000) <-------------------- Delete these two lines SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="08:00:27:d8:8d:15", ATTR{dev_id}=="0x0", ATTR{type}=="1", KERNEL=="eth*", NAME="eth0" # PCI device 0x8086:0x100e (e1000) ---Modify the next line and change eth1 to be eth0 SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="08:00:27:89:84:98", ATTR{dev_id}=="0x0", ATTR{type}=="1", KERNEL=="eth*", NAME="eth1" .csharpcode, .csharpcode pre { font-size: small; color: black; font-family: consolas, "Courier New", courier, monospace; background-color: #ffffff; /*white-space: pre;*/ } .csharpcode pre { margin: 0em; } .csharpcode .rem { color: #008000; } .csharpcode .kwrd { color: #0000ff; } .csharpcode .str { color: #006080; } .csharpcode .op { color: #0000c0; } .csharpcode .preproc { color: #cc6633; } .csharpcode .asp { background-color: #ffff00; } .csharpcode .html { color: #800000; } .csharpcode .attr { color: #ff0000; } .csharpcode .alt { background-color: #f4f4f4; width: 100%; margin: 0em; } .csharpcode .lnum { color: #606060; } ---------------------------------------- --------- Example NEW ----------- # This file was automatically generated by the /lib/udev/write_net_rules # program, run by the persistent-net-generator.rules rules file. # # You can modify it, as long as you keep each rule on a single # line, and change only the value of the NAME= key. # PCI device 0x8086:0x100e (e1000) SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="08:00:27:89:84:98", ATTR{dev_id}=="0x0", ATTR{type}=="1", KERNEL=="eth*", NAME="eth0" .csharpcode, .csharpcode pre { font-size: small; color: black; font-family: consolas, "Courier New", courier, monospace; background-color: #ffffff; /*white-space: pre;*/ } .csharpcode pre { margin: 0em; } .csharpcode .rem { color: #008000; } .csharpcode .kwrd { color: #0000ff; } .csharpcode .str { color: #006080; } .csharpcode .op { color: #0000c0; } .csharpcode .preproc { color: #cc6633; } .csharpcode .asp { background-color: #ffff00; } .csharpcode .html { color: #800000; } .csharpcode .attr { color: #ff0000; } .csharpcode .alt { background-color: #f4f4f4; width: 100%; margin: 0em; } .csharpcode .lnum { color: #606060; } ----------------------------------------

  Read the article

• How Can I Safely Destroy Sensitive Data CDs/DVDs?

  - by Jason Fitzpatrick

  You have a pile of DVDs with sensitive information on them and you need to safely and effectively dispose of them so no data recovery is possible. What’s the most safe and efficient way to get the job done? Today’s Question & Answer session comes to us courtesy of SuperUser—a subdivision of Stack Exchange, a community-driven grouping of Q&A web sites. The Question SuperUser reader HaLaBi wants to know how he can safely destroy CDs and DVDs with personal data on them: I have old CDs/DVDs which have some backups, these backups have some work and personal files. I always had problems when I needed to physically destroy them to make sure no one will reuse them. Breaking them is dangerous, pieces could fly fast and may cause harm. Scratching them badly is what I always do but it takes long time and I managed to read some of the data in the scratched CDs/DVDs. What’s the way to physically destroy a CD/DVD safely? How should he approach the problem? The Answer SuperUser contributor Journeyman Geek offers a practical solution coupled with a slightly mad-scientist solution: The proper way is to get yourself a shredder that also handles cds – look online for cd shredders. This is the right option if you end up doing this routinely. I don’t do this very often – For small scale destruction I favour a pair of tin snips – they have enough force to cut through a cd, yet are blunt enough to cause small cracks along the sheer line. Kitchen shears with one serrated side work well too. You want to damage the data layer along with shearing along the plastic, and these work magnificently. Do it in a bag, cause this generates sparkly bits. There’s also the fun, and probably dangerous way – find yourself an old microwave, and microwave them. I would suggest doing this in a well ventilated area of course, and not using your mother’s good microwave. There’s a lot of videos of this on YouTube – such as this (who’s done this in a kitchen… and using his mom’s microwave). This results in a very much destroyed cd in every respect. If I was an evil hacker mastermind, this is what I’d do. The other options are better for the rest of us. Another contributor, Keltari, notes that the only safe (and DoD approved) way to dispose of data is total destruction: The answer by Journeyman Geek is good enough for almost everything. But oddly, that common phrase “Good enough for government work” does not apply – depending on which part of the government. It is technically possible to recover data from shredded/broken/etc CDs and DVDs. If you have a microscope handy, put the disc in it and you can see the pits. The disc can be reassembled and the data can be reconstructed — minus the data that was physically destroyed. So why not just pulverize the disc into dust? Or burn it to a crisp? While technically, that would completely eliminate the data, it leaves no record of the disc having existed. And in some places, like DoD and other secure facilities, the data needs to be destroyed, but the disc needs to exist. If there is a security audit, the disc can be pulled to show it has been destroyed. So how can a disc exist, yet be destroyed? Well, the most common method is grinding the disc down to destroy the data, yet keep the label surface of the disc intact. Basically, it’s no different than using sandpaper on the writable side, till the data is gone. Have something to add to the explanation? Sound off in the the comments. Want to read more answers from other tech-savvy Stack Exchange users? Check out the full discussion thread here.     

  Read the article

• Friday Tips #3

  - by Chris Kawalek

  Even though yesterday was Thanksgiving here in the US, we still have a Friday tip for those of you around your computers today. In fact, we have two! The first one came in last week via our #AskOracleVirtualization Twitter hashtag. The tweet has disappeared into the ether now, but we remember the gist, so here it is: Question: Will there be an Oracle Virtual Desktop Client for Android? Answer by our desktop virtualization product development team: We are looking at Android as a supported platform for future releases. Question: How can I make a Sun Ray Client automatically connect to a virtual machine? Answer by Rick Butland, Principal Sales Consultant, Oracle Desktop Virtualization: Someone recently asked how they can assign VM’s to specific Sun Ray Desktop Units (“DTU’s”) without any user interfaction being required, without the “Desktop Selector” being displayed, or any User Directory.  That is, they wanted each Sun Ray to power on and immediately connect to a pre-assigned Solaris VM.   This can be achieved by using “tokens” for user assignment – that is, the tokens found on Smart Cards, DTU’s, or OVDC clients can be used in place of user credentials.  Note, however, that mixing “token-only” assignments and “User Directories” in the same VDI Center won’t work.   Much of this procedure is covered in the documentation, particularly here. But it can useful to have everything in one place, “cookbook-style”:  1. Create the “token-only” directory type: From the VDI administration interface, select:  “Settings”, “Company”, “New”, select the “None” radio button, and click “Next.” Enter a name for the new “Company”, and click “Next”, then “Finish.” 2. Create Desktop Providers, Pools, and VM’s as appropriate. 3. Access the Sun Ray administration interface at http://servername:1660 and login using “root” credentials, and access the token-id’s you wish to use for assignment.  If you’re using DTU tokens rather than Smart Card tokens, these can be found under the “Tokens” tab, and “Search-ing” using the “Currently Used Tokens” tab.  DTU’s can be identified by the prefix “psuedo.”   For example: 4. Copy/paste this token into the VDI administrative interface, by selecting “Users”, “New”, and pasting in the token ID, and click “OK” - for example: 5. Assign the token (DTU) to a desktop, that is, in the VDI Admin Gui, select “Pool”, “Desktop”, select the VM, and click "Assign" and select the token you want, for example: In addition to assigning tokens to desktops, you'll need to bypass the login screen.  To do this, you need to do two things:  1.  Disable VDI client authentication with:  /opt/SUNWvda/sbin/vda settings-setprops -p clientauthentication=Disabled 2. Disable the VDI login screen – to do this,  add a kiosk argument of "-n" to the Sun Ray kiosk arguments screen.   You set this on the Sun Ray administration page - "Advanced", "Kiosk Mode", "Edit", and add the “-n” option to the arguments screen, for example: 3.  Restart both the Sun Ray and VDI services: # /opt/SUNWut/sbin/utstart –c # /opt/SUNWvda/sbin/vda-service restart Remember, if you have a question for us, please post on Twitter with our hashtag (again, it's #AskOracleVirtualization), and we'll try to answer it if we can. See you next time!

  Read the article

• 11.10 desktop alerts (volume change and terminal bell) stopped working but all other audio still works

  - by FlabbergastedPickle

  All, My sound works just fine in 11.10 64-bit install on HP dm1-4050 Sandy Bridge notebook (e.g. audio works in Banshee, flash, games, browser, Thunderbird email notification, etc.), but the core desktop notifications (e.g. pressing a tab in a terminal where there is more than one option should trigger a terminal bell, or changing volume using volume keys should be accompanied with the supporting "quack" that the volume app makes) do not work. I've intentionally disabled login sound as explained here on ask ubuntu but even enabling it back makes no difference. These notifications did work before just fine and I am not sure when did the actually stop working but it must've been fairly recently. Only things I did were trying to install some ppa edge xorg drivers for my intel card (a separate issue) but also reverted them all with ppa-purge once I discovered they did not improve anything. Other thing I did was check volume settings with alsamixer and did alsactl store for the soundcard after I did some experimenting with volume settings for PCM (on my laptop PCM at 100% crackles so I had to lower it and make pulseaudio ignore its setting as per ask ubuntu's page). That said, neither of these should have any bearing on the said notifications since the volume is up and they clearly work everywhere else but the core desktop events. The system ready drum sound when Ubuntu boots and user reaches the login screen also does not work. The guest login behaves exactly same as mine. Audio works (including the login sound since I've not disabled it for the guest account), but no quacks when changing the volume or terminal bell sounds... I've tried copying ubuntu sounds to /usr/share/sounds/ as suggested on ask ubuntu and that did not work. I also tried using dconf-editor to check sound theme settings and tried both freedesktop (which is what it was set to) and ubuntu, as suggested on ask ubuntu. This did not work either. I tried purging the ~/.pulse folder and the /tmp/*pulse* entries, rebooting and restarting pulseaudio with -D flag. While audio came back on and behaved just fine in all aspects (e.g. one can adjust volume levels, play music, games, in-browser sound stuff, and other app alerts) except for the system ready drum sound (at the login screen), and any system event (terminal bell and volume change quack sound). It is interesting that the quack sound works inside system settings-sound when adjusting levels there, but it does not when volume is changed via top bar's volume settings... I do recall that at one point yesterday when I was restarting pulseaudio the quacks that accompany volume change did start working but I have no idea what caused that. This was also when I first realized those alerts were not working. After rebooting it was again gone. I did compile my own 3.0.14-rt31 kernel a little while ago as instructed on one of the wiki's for the 11.10 rt kernel. Everything works as before except for the said sound alerts. I am not sure if this began happening since I started using the rt kernel though and yesterday's momentary ability to hear those quacks while changing the volume make me believe that the kernel is not one responsible for this problem. One more thing I can think of is that I used alsoft-conf tool to configure buffering on the OpenAL (due to TA Spring's choppy audio) and changed in there default audio device to ALSA. I also tried reverting it to Pulseaudio as the only allowed output but the bottom part of the Backend tab always reverts to ALSA even when I select Pulseaudio. The pulseaudio does remain as the only active choice on top. This, however, once again does not make any sense in terms of preventing desktop audio alerts when everything else including OpenAL games plays sound just fine... So, there you have it, as verbose as I could make it :-). I tried all I could find on this issue and had no luck so far... Any ideas?

  Read the article

• Merging Social Accounts: What We Learned This Weekend

  - by Mike Stiles

  Guest Post by Erika BrookesWe learned that it’s not always as easy as you think it’s going to be. While it’s widely accepted that merging multiple owned Facebook Pages that are duplicating communities and putting out the same type of content is a best practice, actually pulling it off without rattling fans is a trickier proposition. Facebook is nice and clear about how to merge Facebook Pages. Although content is not carried over, Likes from the pages you’re merging are. So you can imagine the surprise when such fans start seeing posts in their News Feed from a page they don’t believe they ever Liked. One community member accurately likened it to having your bank come under another bank’s brand name. The Facebook Page changes to the new brand, just like your debit card, emails, signs and other communication. This weekend we did our merge. The Facebook communities of Vitrue, Involver and Collective Intellect were pulled into one community, Oracle Social. Could we have handled it better? Oh yeah. Our intent was to make sure, to the fullest extent possible, that the fans of the Vitrue, Involver, and Collective Intellect brand pages were well-informed about the pending page merges in ADVANCE of the merge. While many were aware that Oracle acquired the three companies, many were not. We learned from fan feedback that we should have sent notifications MUCH earlier to make the brand Page merge crystal clear and to answer any questions. That was our bad, our responsibility and we apologize for Oracle Social showing up in your News Feed if you were not aware that it was a result of your fandom of Vitrue, Involver or Collective Intellect. It was our job to make you aware well in advance. Some felt they had never Liked the fan Pages of Vitrue, Involver or Collective Intellect, so they were understandably upset (some cultures may call it “fit to be tied”) when they found themselves fans of Oracle Social. One thing to consider is that since 2009, brands and developers have used and enjoyed free Involver tab apps like Twitter, RSS and YouTube (1.2 million of which are currently active), which included an opt-in Liking the Involver Page. Often, when Liking happens in a manner outside of the traditional clicking of a Like button on a brand Page, it’s easy to forget a Page was indeed Liked. Lastly, a few felt that their Like of the Page had been “bought.” It was not. No fans or Likes were separately purchased. Yes, the companies and the social properties of Vitrue, Involver and Collective Intellect were acquired by Oracle. Those brands are now being coordinated into the larger Oracle brand. In social media, that means those brands are being integrated into the Oracle Social community. So what now? We apologize and apply lessons learned. We learned that you not only have to communicate thoroughly and clearly, but you have to communicate well in advance of any actionable items that will affect fans. We’re more than willing to walk straight to the woodshed when we deserve it. Going forward, the social team here is dedicated to facilitating content, discussion and sharing around social for marketers, agencies, IT stakeholders and social staffs, including community managers. We anticipate Oracle Social being the premier gathering place for true social innovators as we move into social’s exciting next phase of development. Inevitably, some will still feel they are fans of the Page in error. While we hate to see you go, you may unlike the Page if it’s not relevant or useful to you. Let’s continue to contribute, participate, foster our desire to learn, and move forward together positively and constructively - both for current fans of the community and the many fans to come.

  Read the article

• Atheros AR2413 wireless not working after shutdown

  - by Chandrasekhar

  I am using a Ubuntu 11.04 on an Acer aspire 3680 laptop and my wifi is not working. I followed the below commands to install the madwifi driver: sudo su apt-get install subversion cd /usr/src svn checkout http://madwifi-project.org/svn/madwifi/trunk madwifi tar cfvz madwifi.tgz cd madwifi make && make install echo "blacklist ath5k" /etc/modprobe.d/blacklist.conf echo "ath_pci" /etc/modules modprobe ath_pci sudo reboot After installation I am facing the same problem. My wifi wont work after I shutdown. Infact it didn't work after suspend but I rectified that problem by the following commands: Command 1: sudo rmmod -f ath_pci sudo rfkill unblock all sudo modprobe ath_pci along with the command SUSPEND_MODULES=ath_pci added to the /etc/pm/config.d/madwifi directory. So if I suspend and then on my laptop the wifi loads well and doesn't create a problem. But if I shutdown my laptop the wifi never loads again and eachtime I have to run a Ubuntu 9.04 live CD to load it. I did try adding the Command 1 to the /etc/rc.local directory but still it doesn't work. So my question is: What should I do in order to make my wireless work without having to run a live CD of ubuntu 9.04 everytime after shutdown? Thanks. Here are the outputs which one might need: Output 1 chandru@chandru-acer:~$ lspci 00:00.0 Host bridge: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express Memory Controller Hub (rev 03) 00:02.0 VGA compatible controller: Intel Corporation Mobile 945GM/GMS, 943/940GML Express Integrated Graphics Controller (rev 03) 00:02.1 Display controller: Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller (rev 03) 00:1b.0 Audio device: Intel Corporation N10/ICH 7 Family High Definition Audio Controller (rev 02) 00:1c.0 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 1 (rev 02) 00:1c.1 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 2 (rev 02) 00:1c.2 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 3 (rev 02) 00:1d.0 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #1 (rev 02) 00:1d.1 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #2 (rev 02) 00:1d.2 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #3 (rev 02) 00:1d.3 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #4 (rev 02) 00:1d.7 USB Controller: Intel Corporation N10/ICH 7 Family USB2 EHCI Controller (rev 02) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2) 00:1f.0 ISA bridge: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge (rev 02) 00:1f.2 IDE interface: Intel Corporation 82801GBM/GHM (ICH7 Family) SATA IDE Controller (rev 02) 00:1f.3 SMBus: Intel Corporation N10/ICH 7 Family SMBus Controller (rev 02) 02:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8038 PCI-E Fast Ethernet Controller (rev 14) 0a:03.0 Ethernet controller: Atheros Communications Inc. AR2413 802.11bg NIC (rev 01) 0a:09.0 CardBus bridge: Texas Instruments PCIxx12 Cardbus Controller 0a:09.2 Mass storage controller: Texas Instruments 5-in-1 Multimedia Card Reader (SD/MMC/MS/MS PRO/xD) Output 2: lsmod Module Size Used by wlan_tkip 17074 2 binfmt_misc 13213 1 parport_pc 32111 0 ppdev 12849 0 snd_hda_codec_si3054 12924 1 snd_hda_codec_realtek 255882 1 joydev 17322 0 snd_atiixp_modem 18624 0 snd_via82xx_modem 18305 0 snd_intel8x0m 18493 0 snd_ac97_codec 105614 3 snd_atiixp_modem,snd_via82xx_modem,snd_intel8x0m snd_hda_intel 24113 2 ac97_bus 12642 1 snd_ac97_codec snd_hda_codec 90901 3 snd_hda_codec_si3054,snd_hda_codec_realtek,snd_hda_intel i915 451053 3 snd_hwdep 13274 1 snd_hda_codec snd_pcm 80042 7 snd_hda_codec_si3054,snd_atiixp_modem,snd_via82xx_modem,snd_intel8x0m,snd_ac97_codec,snd_hda_intel,snd_hda_codec snd_seq_midi 13132 0 snd_rawmidi 25269 1 snd_seq_midi drm_kms_helper 40971 1 i915 snd_seq_midi_event 14475 1 snd_seq_midi snd_seq 51291 2 snd_seq_midi,snd_seq_midi_event pcmcia 39671 0 snd_timer 28659 2 snd_pcm,snd_seq snd_seq_device 14110 3 snd_seq_midi,snd_rawmidi,snd_seq drm 184164 4 i915,drm_kms_helper yenta_socket 27230 0 tifm_7xx1 12898 0 wlan_scan_sta 21945 1 ath_rate_sample 17279 1 pcmcia_rsrc 18292 1 yenta_socket psmouse 73312 0 tifm_core 15040 1 tifm_7xx1 snd 55295 18 snd_hda_codec_si3054,snd_hda_codec_realtek,snd_atiixp_modem,snd_via82xx_modem,snd_intel8x0m,snd_ac97_codec,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device serio_raw 12990 0 i2c_algo_bit 13184 1 i915 soundcore 12600 1 snd pcmcia_core 21505 3 pcmcia,yenta_socket,pcmcia_rsrc video 19112 1 i915 ath_pci 183044 0 snd_page_alloc 14073 5 snd_atiixp_modem,snd_via82xx_modem,snd_intel8x0m,snd_hda_intel,snd_pcm wlan 224640 5 wlan_tkip,wlan_scan_sta,ath_rate_sample,ath_pci ath_hal 398701 3 ath_rate_sample,ath_pci lp 13349 0 parport 36746 3 parport_pc,ppdev,lp usbhid 41704 0 hid 77084 1 usbhid sky2 49172 0 Output 3 root@chandru-acer:~# lshw -C network PCI (sysfs) *-network description: Ethernet interface product: 88E8038 PCI-E Fast Ethernet Controller vendor: Marvell Technology Group Ltd. physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 14 serial: 00:16:36:fb:aa:64 capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=sky2 driverversion=1.28 firmware=N/A latency=0 link=no multicast=yes port=twisted pair resources: irq:43 memory:44000000-44003fff ioport:2000(size=256) *-network description: Wireless interface product: AR2413 802.11bg NIC vendor: Atheros Communications Inc. physical id: 3 bus info: pci@0000:0a:03.0 logical name: wifi0 version: 01 serial: 00:19:7d:d3:0c:fd width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list logical ethernet physical wireless configuration: broadcast=yes driver=ath_pci ip=192.168.1.6 latency=96 maxlatency=28 mingnt=10 multicast=yes wireless=IEEE 802.11g resources: irq:18 memory:d0000000-d000ffff Output 4 root@chandru-acer:~# lsmod | grep ath_pci ath_pci 183044 0 wlan 224640 5 wlan_tkip,wlan_scan_sta,ath_rate_sample,ath_pci ath_hal 398701 3 ath_rate_sample,ath_pci

  Read the article

• WiFi stops working after a while in Lenovo ThinkPad W520 (Ubuntu 12.04)

  - by el10780

  After several minutes(I do not know how many) there is no internet connection on my laptop via Wi-Fi.Ubuntu doesn't show any kind of message that my WiFi was disconnected neither there is a signal drop,but suddenly Firefox stops connecting to web pages.I checked my modem/router and it seems that it is working fine.I tried also to reboot the WiFi device and nothing happens.The only thing that it makes it work again is a reboot of the system and if I do not want to do a reboot then I am enforced to connect to the Internet using Ethernet cable.Does anybody know what is happening? ## Some Hardware info that might be helpful ## el10780@ThinkPad-W520:~$ sudo lshw -class network *-network description: Ethernet interface product: 82579LM Gigabit Network Connection vendor: Intel Corporation physical id: 19 bus info: pci@0000:00:19.0 logical name: eth0 version: 04 serial: f0:de:f1:f1:be:10 size: 100Mbit/s capacity: 1Gbit/s width: 32 bits clock: 33MHz capabilities: pm msi bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=e1000e driverversion=1.5.1-k duplex=full firmware=0.13-3 ip=192.168.0.10 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:50 memory:f3a00000-f3a1ffff memory:f3a2b000-f3a2bfff ioport:6080(size=32) *-network description: Wireless interface product: Centrino Advanced-N + WiMAX 6250 vendor: Intel Corporation physical id: 0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 5e serial: 64:80:99:63:14:74 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.2.0-26-generic firmware=41.28.5.1 build 33926 ip=192.168.0.6 latency=0 link=yes multicast=yes wireless=IEEE 802.11abgn resources: irq:52 memory:f3900000-f3901fff *-network description: Ethernet interface physical id: 1 bus info: usb@2:1.3 logical name: wmx0 serial: 00:1d:e1:53:b2:e8 capabilities: ethernet physical configuration: driver=i2400m firmware=i6050-fw-usb-1.5.sbcf link=no el10780@ThinkPad-W520:~$ lspci 00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) 00:01.0 PCI bridge: Intel Corporation Xeon E3-1200/2nd Generation Core Processor Family PCI Express Root Port (rev 09) 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 00:16.0 Communication controller: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 (rev 04) 00:16.3 Serial controller: Intel Corporation 6 Series/C200 Series Chipset Family KT Controller (rev 04) 00:19.0 Ethernet controller: Intel Corporation 82579LM Gigabit Network Connection (rev 04) 00:1a.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 (rev 04) 00:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 (rev b4) 00:1c.1 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 2 (rev b4) 00:1c.3 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 4 (rev b4) 00:1c.4 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 5 (rev b4) 00:1c.6 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 7 (rev b4) 00:1d.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 (rev 04) 00:1f.0 ISA bridge: Intel Corporation QM67 Express Chipset Family LPC Controller (rev 04) 00:1f.2 SATA controller: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller (rev 04) 00:1f.3 SMBus: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller (rev 04) 01:00.0 VGA compatible controller: NVIDIA Corporation GF108 [Quadro 1000M] (rev a1) 03:00.0 Network controller: Intel Corporation Centrino Advanced-N + WiMAX 6250 (rev 5e) 0d:00.0 System peripheral: Ricoh Co Ltd Device e823 (rev 08) 0d:00.3 FireWire (IEEE 1394): Ricoh Co Ltd R5C832 PCIe IEEE 1394 Controller (rev 04) 0e:00.0 USB controller: NEC Corporation uPD720200 USB 3.0 Host Controller (rev 04) el10780@ThinkPad-W520:~$ rfkill list all 0: hci0: Bluetooth Soft blocked: no Hard blocked: no 1: tpacpi_bluetooth_sw: Bluetooth Soft blocked: no Hard blocked: no 2: phy0: Wireless LAN Soft blocked: no Hard blocked: no 3: i2400m-usb:2-1.3:1.0: WiMAX Soft blocked: yes Hard blocked: no The weirdest thing is this screenshot which I took after running the **Additional Drivers** program.I mean I have a NVidia Quadro 1000M and my Intel Centrino WiFi Card and this shows that there are not proprietay drivers for my system. http://imageshack.us/photo/my-images/268/screenshotfrom201207062.png/

  Read the article

• Graphics trouble after resuming from hibernate or suspend

  - by Voyagerfan5761

  I have a Dell Inspiron 2650 (with NVidia graphics, using nouveau drivers) that I'm using to try out Ubuntu. It's all great, except that Hibernate and Suspend aren't usable. Yes, I know that questions about power-save issues are rampant in the Linux support universe, but it seems that every time I find a solution it's for a very specific hardware combination and doesn't apply to me. So anyway, here goes. When I resume from either power-saving mode, I'll get graphics problems anywhere on the range from a few scattered random-colored pixels that won't change; all the way to full-screen patterns that don't change as I move the mouse, hit keys on the keyboard, or even bring up the shutdown dialog using the power button. Those full-screen issues (which may involve stripes with random pixels, partial black screen, or both) always end in me forcing the machine to shut down by holding the power button. I haven't done much testing yet to determine what severity level is most commonly associated with each mode, but I do avoid using either power-save option because of these issues. I'll add info on my hardware as I can gather it (no home internet connection, and this laptop is tethered to my desk by a dead battery and casing degradation). Please feel free to request something specific in the question comments. Hardware Info See this hardinfo report for my system's hardware configuration. (No, my username is not "myuser"; I sanitized hardinfo's output before publishing it.) Screenshots These screenshots are from a relatively mild occurrence, which happened after the second hibernation I took that session. The first one worked great, though I used the wireless card and Firefox heavily between the two hibernation attempts. Take a look at what happened when I opened my home directory in Nautilus and scrolled it: See below for the situations I've tested so far. The real trouble comes when the machine resumes to an unusable state; in such cases I can't even unlock the screen or properly reboot, much less take a screenshot. I have a hunch that putting a CD in the drive will cause such major failures, and I will try that at some point; see related question. Situations Tested Maverick (10.10) Suspend Seems to suspend nicely with nothing running Seems to suspend nicely with flash drive plugged in On resume from suspend with no flash drive, Terminal and gedit running: Funky graphics on top of log output, then blank screen with pixelated cursor; no response to power button (normally will shutdown 60 seconds later) Hibernate Seems to hibernate nicely with nothing running Seems to hibernate nicely with a few apps (Terminal, Mouse preferences) running Seems to not hibernate when flash drive plugged in Seems to not hibernate when System Monitor is running Have encountered failed hibernation (after several hours and one successful hibernate/thaw cycle) with no external media connected and no programs running except normal background stuff Natty LiveCD (11.04_2010-12-22) When I tested it, Natty wouldn't stay logged in. It played part of the login sound and then [ OK ] appeared in the top right corner (white-on-black terminal text) for a few seconds. Then it kicked me back to the Unlock screen. It did that four times before I gave up and just tested suspend from the Unlock screen. Suspend Resumed to vertical gray and black lines 2px (?) wide, then shifted to vertical "jail bars" of black over a black screen with above-described random pixels and mouse pointer. No apparent response to input from mouse (clicking randomly). Keyboard and touchpad unrecognized.

  Read the article

< Previous Page | 298 299 300 301 302 303 304 305 306 307 308 309  | Next Page >