Search Results

Search found 10198 results on 408 pages for 'red and the community'.

Page 313/408 | < Previous Page | 309 310 311 312 313 314 315 316 317 318 319 320  | Next Page >

• CheckPoint/Amazon VPC VPN tunnel working inconsistently

  - by Lee

  First time poster, so please be gentle and correct me if there's Server Fault etiquette I'm missing. We have two CheckPoint edge devices at sites A & B, independently managed, connecting to two Amazon private clouds. In both cases, the two Amazon VPCs are in the same community on the CheckPoint device. A VPN tunnel exists between the two CheckPoint devices as well. Between Sites A & B and the Amazon VPC in Northern Virigina, we are unable to keep more than one tunnel up. Both will come up, but tunnel 2 will drop an hour after initiation and will not come back up while tunnel 1 is up. We believe the 1-hour period is due to IPsec phase 2 renegotiation, but can't be sure. On our side, we see the tunnel 2 remote endpoint as not responding to phase 2 negotiation. Between Sites A & B and the Amazon VPC in Oregon, we have no issues. Both tunnels are up and fail over properly. The CheckPoint gateways are using domain-based VPNs. According to CheckPoint's advice to Amazon, this won't work. Yet, in Oregon, it does. We've pursued this with Amazon and, despite the fact it's working in Oregon, they've refused to troubleshoot with us further. Can anyone suggest anything we can do to try to get this stabilized? Going to route-based VPNs is not an option for us.

  Read the article

• Cannot print certain colours on Ubuntu with HP Laser Printer

  - by ILMV

  We have a load of machines running Ubuntu in our office, they are either on 8.04 or 9.10. We have a server which connects a HP JetDirect that connects to a HP 3550 Colour Laser printer using CUPS. The problem we are having is we cannot print red, magenta or yellow at 100%, I've got a picture of the Ubuntu test page to demonstrate my problem: This is obviously a pretty big problem as we are constantly receiving documents with these colours and cannot successfully print them off, we cannot just switch the grayscale, our business depends on being able to print colour (seems trivial but we handle lots of artwork). We're using the recommended driver HP Color LaserJet 3550 footmatic/pxljr (recommended), there is another driver in the list labelled HP Color LaserJet 3550 footmatic/hpijs. These are production printers so need to make sure any setting change won't kick is in the nuts. It would appear HPIJS is for HP Inkjets, makes sense I guess. The problem doesn't occur in Windows. RESOLVED I've managed to solve the problem, I did indeed use the HPIJS driver (apparently for inkjets) but it seems to have worked, we're going to roll with it for now to see how we get on with it.

  Read the article

• How to use webdav and user dir in the same time in the same section ?

  - by Louis

  Dear community, i would like to mount trough webdav my https://myserver/~user_account but not https://myserver/. What i am doing now is : <IfModule mod_userdir.c> UserDir public_html UserDir disabled root <Directory /banonymous/data/home/*/public_html> DAV On AllowOverride FileInfo Limit AuthConfig Options MultiViews SymLinksIfOwnerMatch IncludesNoExec <Limit GET POST OPTIONS> Order allow,deny Allow from all </Limit> <LimitExcept GET POST OPTIONS> Order deny,allow Deny from all </LimitExcept> </Directory> </IfModule> and i am setting the authentification in the .htaccess of eache user. AuthType Basic AuthName "Password Required" AuthUserFile /etc/apache2/users/htpasswd Require User geeky It does not work. Is there someone who can tell me if it is possible ? and if it is how to do it. My dream would have been to put the Dav On in the .htaccess.

  Read the article

• The email address used to help trust my PC, is no longer valid, how do I fix that?

  - by Rod

  A few nights ago I upgraded my Windows 7 PC to Windows 8. This morning, when I logged into my PC, I noticed the little flag in the system tray, in desktop mode, had a red "X" on it. I checked it and one of the issues was my needing to tell Windows 8 that I trusted my PC. I clicked on the link to trust my PC, and saw the button to tell it to trust my PC, and so I did. After doing that it send it had sent out an email to a really old email address I had, which hasn't been valid for many years. Now what? Will that "trusting my PC" be invalid, because I can't respond to it (which certainly isn't true, if it's sending messages to so old email address). I didn't even know that Windows still had such an old email address. I'm concerned that I won't have a trust relationship with my own PC, that somehow or other whatever holds onto my information has old information and that I am not sure how to change it in as fast a manner as possible so that I can trust my own PC. How do I do these things?

  Read the article

• Startup script for Red5 on Ubuntu 9.04

  - by user49249

  I am creating startup script for Red5 on Ubuntu. Red5 is installed in /opt/red5 Following is a working script on a CentOS Box on which Red5 is running [code] ==========Start init script ========== #!/bin/sh PROG=red5 RED5_HOME=/opt/red5/dist DAEMON=$RED5_HOME/$PROG.sh PIDFILE=/var/run/$PROG.pid # Source function library . /etc/rc.d/init.d/functions [ -r /etc/sysconfig/red5 ] && . /etc/sysconfig/red5 RETVAL=0 case "$1" in start) echo -n $"Starting $PROG: " cd $RED5_HOME $DAEMON >/dev/null 2>/dev/null & RETVAL=$? if [ $RETVAL -eq 0 ]; then echo $! > $PIDFILE touch /var/lock/subsys/$PROG fi [ $RETVAL -eq 0 ] && success $"$PROG startup" || failure $"$PROG startup" echo ;; stop) echo -n $"Shutting down $PROG: " killproc -p $PIDFILE RETVAL=$? echo [ $RETVAL -eq 0 ] && rm -f /var/lock/subsys/$PROG ;; restart) $0 stop $0 start ;; status) status $PROG -p $PIDFILE RETVAL=$? ;; *) echo $"Usage: $0 {start|stop|restart|status}" RETVAL=1 esac exit $RETVAL [/code] What do I need to replace for Ubuntu in the above script. My Red5 is in /opt/red5/ and to start it manually I always do /opt/red5/dist/red5.sh from Ubuntu As I did not find rc.d/functions on Ubuntu on my laptop also /etc/init.d/functions I did not existed. I would like to be able to use them with service as Red hat distributions do. I checked /lib/lsb/init-functions.

  Read the article

• Cisco ASA: How to route PPPoE-assigned subnet?

  - by Martijn Heemels

  We've just received a fiber uplink, and I'm trying to configure our Cisco ASA 5505 to properly use it. The provider requires us to connect via PPPoE, and I managed to configure the ASA as a PPPoE client and establish a connection. The ASA is assigned an IP address by PPPoE, and I can ping out from the ASA to the internet, but I should have access to an entire /28 subnet. I can't figure out how to get that subnet configured on the ASA, so that I can route or NAT the available public addresses to various internal hosts. My assigned range is: 188.xx.xx.176/28 The address I get via PPPoE is 188.xx.xx.177/32, which according to our provider is our Default Gateway address. They claim the subnet is correctly routed to us on their side. How does the ASA know which range it is responsible for on the Fiber interface? How do I use the addresses from my range? To clarify my config; The ASA is currently configured to default-route to our ADSL uplink on port Ethernet0/0 (interface vlan2, nicknamed Outside). The fiber is connected to port Ethernet0/2 (interface vlan50, nicknamed Fiber) so I can configure and test it before making it the default route. Once I'm clear on how to set it all up, I'll fully replace the Outside interface with Fiber. My config (rather long): : Saved : ASA Version 8.3(2)4 ! hostname gw domain-name example.com enable password ****** encrypted passwd ****** encrypted names name 10.10.1.0 Inside-dhcp-network description Desktops and clients that receive their IP via DHCP name 10.10.0.208 svn.example.com description Subversion server name 10.10.0.205 marvin.example.com description LAMP development server name 10.10.0.206 dns.example.com description DNS, DHCP, NTP ! interface Vlan2 description Old ADSL WAN connection nameif outside security-level 0 ip address 192.168.1.2 255.255.255.252 ! interface Vlan10 description LAN vlan 10 Regular LAN traffic nameif inside security-level 100 ip address 10.10.0.254 255.255.0.0 ! interface Vlan11 description LAN vlan 11 Lab/test traffic nameif lab security-level 90 ip address 10.11.0.254 255.255.0.0 ! interface Vlan20 description LAN vlan 20 ISCSI traffic nameif iscsi security-level 100 ip address 10.20.0.254 255.255.0.0 ! interface Vlan30 description LAN vlan 30 DMZ traffic nameif dmz security-level 50 ip address 10.30.0.254 255.255.0.0 ! interface Vlan40 description LAN vlan 40 Guests access to the internet nameif guests security-level 50 ip address 10.40.0.254 255.255.0.0 ! interface Vlan50 description New WAN Corporate Internet over fiber nameif fiber security-level 0 pppoe client vpdn group KPN ip address pppoe ! interface Ethernet0/0 switchport access vlan 2 speed 100 duplex full ! interface Ethernet0/1 switchport trunk allowed vlan 10,11,30,40 switchport trunk native vlan 10 switchport mode trunk ! interface Ethernet0/2 switchport access vlan 50 speed 100 duplex full ! interface Ethernet0/3 shutdown ! interface Ethernet0/4 shutdown ! interface Ethernet0/5 switchport access vlan 20 ! interface Ethernet0/6 shutdown ! interface Ethernet0/7 shutdown ! boot system disk0:/asa832-4-k8.bin ftp mode passive clock timezone CEST 1 clock summer-time CEDT recurring last Sun Mar 2:00 last Sun Oct 3:00 dns domain-lookup inside dns server-group DefaultDNS name-server dns.example.com domain-name example.com same-security-traffic permit inter-interface same-security-traffic permit intra-interface object network inside-net subnet 10.10.0.0 255.255.0.0 object network svn.example.com host 10.10.0.208 object network marvin.example.com host 10.10.0.205 object network lab-net subnet 10.11.0.0 255.255.0.0 object network dmz-net subnet 10.30.0.0 255.255.0.0 object network guests-net subnet 10.40.0.0 255.255.0.0 object network dhcp-subnet subnet 10.10.1.0 255.255.255.0 description DHCP assigned addresses on Vlan 10 object network Inside-vpnpool description Pool of assignable addresses for VPN clients object network vpn-subnet subnet 10.10.3.0 255.255.255.0 description Address pool assignable to VPN clients object network dns.example.com host 10.10.0.206 description DNS, DHCP, NTP object-group service iscsi tcp description iscsi storage traffic port-object eq 3260 access-list outside_access_in remark Allow access from outside to HTTP on svn. access-list outside_access_in extended permit tcp any object svn.example.com eq www access-list Insiders!_splitTunnelAcl standard permit 10.10.0.0 255.255.0.0 access-list iscsi_access_in remark Prevent disruption of iscsi traffic from outside the iscsi vlan. access-list iscsi_access_in extended deny tcp any interface iscsi object-group iscsi log warnings ! snmp-map DenyV1 deny version 1 ! pager lines 24 logging enable logging timestamp logging asdm-buffer-size 512 logging monitor warnings logging buffered warnings logging history critical logging asdm errors logging flash-bufferwrap logging flash-minimum-free 4000 logging flash-maximum-allocation 2000 mtu outside 1500 mtu inside 1500 mtu lab 1500 mtu iscsi 9000 mtu dmz 1500 mtu guests 1500 mtu fiber 1492 ip local pool DHCP_VPN 10.10.3.1-10.10.3.20 mask 255.255.0.0 ip verify reverse-path interface outside no failover icmp unreachable rate-limit 10 burst-size 5 asdm image disk0:/asdm-635.bin asdm history enable arp timeout 14400 nat (inside,outside) source static any any destination static vpn-subnet vpn-subnet ! object network inside-net nat (inside,outside) dynamic interface object network svn.example.com nat (inside,outside) static interface service tcp www www object network lab-net nat (lab,outside) dynamic interface object network dmz-net nat (dmz,outside) dynamic interface object network guests-net nat (guests,outside) dynamic interface access-group outside_access_in in interface outside access-group iscsi_access_in in interface iscsi route outside 0.0.0.0 0.0.0.0 192.168.1.1 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 dynamic-access-policy-record DfltAccessPolicy aaa-server SBS2003 protocol radius aaa-server SBS2003 (inside) host 10.10.0.204 timeout 5 key ***** aaa authentication enable console SBS2003 LOCAL aaa authentication ssh console SBS2003 LOCAL aaa authentication telnet console SBS2003 LOCAL http server enable http 10.10.0.0 255.255.0.0 inside snmp-server host inside 10.10.0.207 community ***** version 2c snmp-server location Server room snmp-server contact [email protected] snmp-server community ***** snmp-server enable traps snmp authentication linkup linkdown coldstart snmp-server enable traps syslog crypto ipsec transform-set TRANS_ESP_AES-256_SHA esp-aes-256 esp-sha-hmac crypto ipsec transform-set TRANS_ESP_AES-256_SHA mode transport crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 crypto dynamic-map outside_dyn_map 20 set pfs group5 crypto dynamic-map outside_dyn_map 20 set transform-set TRANS_ESP_AES-256_SHA crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5 crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP crypto map outside_map interface outside crypto isakmp enable outside crypto isakmp policy 1 authentication pre-share encryption 3des hash sha group 2 lifetime 86400 telnet 10.10.0.0 255.255.0.0 inside telnet timeout 5 ssh scopy enable ssh 10.10.0.0 255.255.0.0 inside ssh timeout 5 ssh version 2 console timeout 30 management-access inside vpdn group KPN request dialout pppoe vpdn group KPN localname INSIDERS vpdn group KPN ppp authentication pap vpdn username INSIDERS password ***** store-local dhcpd address 10.40.1.0-10.40.1.100 guests dhcpd dns 8.8.8.8 8.8.4.4 interface guests dhcpd update dns interface guests dhcpd enable guests ! threat-detection basic-threat threat-detection scanning-threat threat-detection statistics host number-of-rate 2 threat-detection statistics port number-of-rate 3 threat-detection statistics protocol number-of-rate 3 threat-detection statistics access-list threat-detection statistics tcp-intercept rate-interval 30 burst-rate 400 average-rate 200 ntp server dns.example.com source inside prefer webvpn group-policy DfltGrpPolicy attributes vpn-tunnel-protocol IPSec l2tp-ipsec group-policy Insiders! internal group-policy Insiders! attributes wins-server value 10.10.0.205 dns-server value 10.10.0.206 vpn-tunnel-protocol IPSec l2tp-ipsec split-tunnel-policy tunnelspecified split-tunnel-network-list value Insiders!_splitTunnelAcl default-domain value example.com username martijn password ****** encrypted privilege 15 username marcel password ****** encrypted privilege 15 tunnel-group DefaultRAGroup ipsec-attributes pre-shared-key ***** tunnel-group Insiders! type remote-access tunnel-group Insiders! general-attributes address-pool DHCP_VPN authentication-server-group SBS2003 LOCAL default-group-policy Insiders! tunnel-group Insiders! ipsec-attributes pre-shared-key ***** ! class-map global-class match default-inspection-traffic class-map type inspect http match-all asdm_medium_security_methods match not request method head match not request method post match not request method get ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum 512 policy-map type inspect http http_inspection_policy parameters protocol-violation action drop-connection policy-map global-policy class global-class inspect dns inspect esmtp inspect ftp inspect h323 h225 inspect h323 ras inspect http inspect icmp inspect icmp error inspect mgcp inspect netbios inspect pptp inspect rtsp inspect snmp DenyV1 ! service-policy global-policy global smtp-server 123.123.123.123 prompt hostname context call-home profile CiscoTAC-1 no active destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address email [email protected] destination transport-method http subscribe-to-alert-group diagnostic subscribe-to-alert-group environment subscribe-to-alert-group inventory periodic monthly subscribe-to-alert-group configuration periodic monthly subscribe-to-alert-group telemetry periodic daily hpm topN enable Cryptochecksum:a76bbcf8b19019771c6d3eeecb95c1ca : end asdm image disk0:/asdm-635.bin asdm location svn.example.com 255.255.255.255 inside asdm location marvin.example.com 255.255.255.255 inside asdm location dns.example.com 255.255.255.255 inside asdm history enable

  Read the article

• Xen guests accessing LUNs

  - by mechcow

  We are using RHEL5.3 with a Clarion SAN attached by FC. Our situation is that we have a number of LUNs presented to Hosts and we want to dynamically present the LUNs to Xen Guests. We are not sure on what the best practice approach is to set this up. The Xen guests will form a cluster together and need the LUNs only for data partitions, i.e. when they are actively running services. So one approach would be to always present all disks to all Xen guests, and then rely up on the cluster software, and mount itself, to not mount the disk twice in two locations. This sounds kinda risky and also is not very secure (one cracked guest can see/destroy all the data). Another approach would be to dynamically add and remove the disks from the Xen guests at the dom0 level (using xm block-attach). This could work but sounds slightly complicated, I'm wondering whether Red Hat Cluster Suite supports this in some way or whether there are scripts to do this. Yet another approach would be to have the LUNs endpointed at the Xen guests themselves - I'm not sure whether this is technically possible since the multipathing has to be done at the Host level.

  Read the article

• Mysql queries stuck in "sending data" state

  - by MarkPW

  I'm running a Litespeed web server and a database server (2 x Clovertown 5335) with MySQL 5.1.52-log (running on Cent OS 4.5 and 4.6 32bit respectively). Last week, I upgraded from 5.0.51a-community-log and since then I've been having a problem whereby my database server's load starts increasing for no apparent reason. Running SHOW PROCESSLIST; I see all of my SQL_CACHE queries that use a wildcard in WHERE, backing up and getting stuck in "sending data" state. However, other queries that use SQL_CACHE but no wildcard do not get caught up in this. To get things going again, the first time it happens (after about 24 hours), I have to restart mysql. 4/5 times it will re-occur after about 20 minutes or so and this time and for subsequent occurrences it is not necessary to restart mysql. Simply stopping the web server for a few minutes will suffice while I allow the stuck queries to clear themselves up. I had no such problem with the the previous mysql install. What could be causing the issue and how do I resolve it? Thanks

  Read the article

• Parental Controls in Ubuntu - per user

  - by Hamish Downer

  I would like to set up parental controls on Ubuntu for a friend of mine. I want it so that the child user has the controls set, but the parent user is not restricted. To be clear, they are sharing one computer, so a router based solution won't help. And I would like a set of step by step instructions to do this. Just one way of doing it. I'm an experienced Ubuntu user, happy at the command line. I've spent quite some time googling for this along the way. I hope that the GChildCare project will eventually make this easy, but it is not ready yet. In the meantime, the WebContentControl GUI provides a way of managing parental controls, but apply them to every user on the computer (easy WebContentContol install instructions and detailed instructions, discussion and related links on ubuntuforums). The ubuntuforums post has a FAQ that states that user-specific configuration is not possible with WebContentControl, and then provides 3 links he used to help him do it. But they are far from step by step instructions. There is this thread which is notes along the way and linking to this article about squid and dansguardian. And then to these two dansguardian articles which are somewhat in depth ... So does anyone know of an existing guide to how to set up parental controls on ubuntu with some users not affected? If no one has come up with an answer after a little bit, I'll set up a community wiki answer so we can come up with a guide.

  Read the article

• "Learning" Linux

  - by Strider

  I've been interested in computers for a long time and have fiddled with a lot of stuff which includes Linux. I started out with Red Hat when I was young (around 13) and lost all data, converting a FAT32 drive to something else. Later it was Knoppix which was really helpful in recovery and such. Then, it was Ubuntu. Also, I fiddled with Arch for some time, but, it breaks too often for my liking (maybe, I should have been more careful). Anyway, currently I use Ubuntu 9.04. I want to dig deeper into the Linux world now. I want to learn how things work and use the terminal more. I am a programmer as well, so, it will help a lot. So, the thing I wanted to ask were: Good books to learn and understand Linux Good habits to use Linux more efficiently. Good tools about which I should know. Amount of time you set aside to learn about new things each day. As a programmer, how do you setup and use Linux efficiently. Long list. I will be grateful to the answerers.

  Read the article

• Fast Ethernet module for Cisco 2620

  - by Kenny Rasschaert

  I have a Cisco 2620 Router. It comes with one fast ethernet port built in (circled in red), and one old AUI ethernet module is installed (circled in blue). I figure I can put a transceiver on the AUI interface to get a second RJ45 connector. What I'd really like to have is a second fast ethernet connector. The ideal candidate to achieve this would be the NM-1FE-TX module. Cisco claims on their website that this module is not suitable for the Cisco 2620 and Cisco 2620XM. It says so in "Table 2 Physical Limitation of Serial Modules per Chassis". Indeed, this module was designed for the 3600 series of routers. I've seen claims on the internet, however, of people having this module on a 2620XM, and it being fully functional. This claim gains some credibility because of the fact that in Cisco's own Packet Tracer software, you can install this module on the 2620XM router. I'm looking for a definitive answer. Will this module work on a Cisco 2620? Is there perhaps another way to get a second fast ethernet port on this device?

  Read the article

• ssh timeout issue connecting to an EC2 instance on OS X

  - by mamusr

  I am new to AWS and not a networking expert but curious to know more about it. I created a VPC with a public subnet only. Then i created an EC2 instance using an Ubuntu 14.04 64-bit pv AMI image (ami-e84d8480) as well generating the key pair needed to connect to it through ssh. I followed amazon's instructions to connect to an EC2 instance via ssh which did not work. Here is my attempted input and debug log: Running on OS X 10.9.4 user$ ssh -vvv -i key.pem [email protected] OpenSSH_6.2p2, OSSLShim 0.9.8r 8 Dec 2011 debug1: Reading configuration data /etc/ssh_config debug1: /etc/ssh_config line 20: Applying options for * debug1: /etc/ssh_config line 102: Applying options for * debug2: ssh_connect: needpriv 0 debug1: Connecting to xxx.xxx.xxx.xxx [xxx.xxx.xxx.xxx] port 22. debug1: connect to address xxx.xxx.xxx.xxx port 22: Operation timed out ssh: connect to host xxx.xxx.xxx.xxx port 22: Operation timed out To attempt to resolve the issue: I enabled the SSH port. Tried different usernames other than ubuntu, like ec2-user and root. Initially set an inbound ssh rule in the security group to connect to only my ip address. When that did not work, i changed it to allow any ip to connect. But those actions did not fix the problem. Here are my guesses as to what i am missing in getting the EC2 instance connection to work. My etc/ssh_config file may be preventing the connection from taking place. I may have missed an important networking detail when setting up the VPC. I do not have a public ip address specified for the instance. I am connecting through the private ip address. My questions for the community: Am i going about it the wrong way connecting to the instance through the private ip address? if so, do i need to specify a public ip address for it to connect or some other method?

  Read the article

• RAID 5 Install on Ubuntu Server 12.04 [closed]

  - by tarabyte

  Environment: Ubuntu Server 12.04, installing from bootable flash drive Error: No root file system is defined. Please correct this from the partitioning menu. I'm trying to set up a personal file server with software RAID 5. I just got three hard drives for this, but haven't found any solid documentation. I'm unsure what the basic way to partition my hard drives is. Can someone upload a screenshot of their "partition disks" screen so that I can compare with mine (attached)? Should I set the bootable flag? Do I need a /home partition? A /boot partition? Should I "Use [my partition] as: Ext4 journaling file system"? Or make that field "physical volume for RAID"? I am an engineer, but I have only a cursory knowledge of all-things-linux. If you know of any good learning resources I'd be happy to hear about those too (that way I don't have to blindly follow deprecated tutorials online). well, image would be here but i don't have a high enough reputation yet (please vote up :)) Thank you, References I've looked into: https://help.ubuntu.com/community/Installation/SoftwareRAID https://help.ubuntu.com/12.04/serverguide/advanced-installation.html http://forevergeeks.com/setup-ubuntu-server-with-raid-5/

  Read the article

• SYS-5016T-MTFB will not POST without manual assistance (Motherboard: X8STi-F)

  - by Dan

  I have a Supermicro 5016T-MTFB 1U server which I am in the process of setting up, but it has a really strange problem. When the system is powered on it will not POST until I press the reset button a few times, followed by pressing the delete key on the keyboard to "wake it up". If I power it on and do nothing, the fans spin up but nothing else happens at all. After pressing the reset button once, the red "overheat" light comes on and blinks which is supposed to indicate a fan failure - but all the fans are working. Pressing reset again usually stops the blinking, and the system starts the normal POST routine but it will not actually get to the bios screen unless I press delete. If I don't press delete, it just continues to hang. After pressing delete it will take me into the bios setup screen, if I exit without saving changes I can boot the system normally. I was able to successfully install Linux with no trouble...but upon rebooting the same problem happened again. This board has integrated IPMI which I thought was the problem, so I disabled it via the jumper on the board. Did not help. Each time this system powers on, it goes on for a second, then turns off again for another second, then turns back on again. I don't know why it does that. Here is what I put in the system: 1 x Xeon E5630 (Nehalem) 80W TDP (it's not overheating, CPU temps stay under 40 degrees C) 2 x Kingston 2GB x 3 DDR3-1066 Memory ECC, unbuffered, unregistered (kvr1066d3e7sk3/6g) 1 x Intel X25-M 160 GB 2 x Western Digital RE3 1TB

  Read the article

• Looking for a short term solution to improve website performance with additional server

  - by Tanim Mirza

  I am working with a small team to run an internal website running with PHP 5.3.9, MySQL 5.0.77. All the files and database are hosted on a dedicated Linux machine with the following configuration: Intel Xeon E5450 8 CPU cores @3.00GHz, 2992.498 MHz, Cache 6148 KB, Cent OS – Red Hat Enterprise Linux Server release 5.4 We started small and then the database got bigger and now the website performance degraded significantly. We often get server space overrun, mysql overloaded with too many calls, etc. We don't have much experience dealing with these issues. We recently got another server that we were thinking to use to improve performance. Since it has better configuration, some of us wanted to completely move everything to the new machine. But I am trying to find out how we can utilize both machine for optimized performance. I found options such as MySQL clustering, Load balancer, etc. I was wondering if I could get any suggestion for this situation "How to utilize two machines in short term for best performance", that would be great. By short term we are looking for something that we can deploy in a month or so. Thanks in advance for your time.

  Read the article

• Problems with image/file upload in MediaWiki on Windows 2008 Server R2, using wrong temp directory

  - by Lasse V. Karlsen

  I have installed MediaWiki 1.15.2 under IIS as per the MediaWiki installation instructions for Windows 2008 Server. I have configured PHP to use a specific temp directory: upload_tmp_dir="C:\php\uploadtemp" I have specified that MediaWiki is allowed to upload: $wgEnableUploads = true; But when I try to upload an image, I get this error message in my browser: Internal error Could not find file "C:\Windows\Temp\php1AEA.tmp". Retrying will simply give me a new filename, but in the same location. The directory does not have any php* files in it, but since they're "temporary", they might be gone in a flash before Windows Explorer is able to show them so that might be a red herring. I've googled for this, and the most promising lead I found was on this page: Image upload problem - Is this bug fixed?, but since the text says "a bugfix was posted on the bug-report page", but provides no link to which bug page this relates to (php or mediawiki) nor the actual bug report, I've not found conclusively the bug report in question so that didn't help me much. Lots of pages indicates that this is a permission issue, so I tried setting permissions on c:\windows\temp as Modify by Everyone, still no dice. I tried changing the two system environment variables TEMP and TMP to point to C:\Temp instead, but MediaWiki still complains about not finding the file in C:\Windows\Temp. Note that I don't care a lot about where the files will actually be stored temporarily, so c:\windows\temp is fine by me. I do, however, care about them actually being uploaded correctly. Does anyone know of a fix, have any leads I can follow, or whatnot? The server is running Windows 2008 Server R2, all patches installed, and the PHP installed is 5.3.2, using IIS FastCGI.

  Read the article

• moving plone or recovering data

  - by Atilla Filiz

  I had a simple plone site running on my Ubuntu 8.10 box, setup by following instructions on https://help.ubuntu.com/community/forum/server/Plone Now the computer got an Ubuntu 9.04 install from scratch, and I want to get the site up and running. As far as I understand several python libraries from 9,04 are not compatible with plone. I tried installing plon3-site from ubuntu repos, and I got this: $bin/instance start Traceback (most recent call last): File "bin/instance", line 103, in ? import plone.recipe.zope2instance.ctl File "/media/Robocup2009/robocup2009/eggs/plone.recipe.zope2instance-2.7-py2.4.egg/plone/recipe/zope2instance/__init__.py", line 16, in ? import zc.buildout File "/media/Robocup2009/robocup2009/eggs/zc.recipe.egg-1.1.0-py2.4.egg/zc/__init__.py", line 1, in ? __import__('pkg_resources').declare_namespace(__name__) ImportError: No module named pkg_resources I have python-pkg-resources installed. I actually don't care about plone, I just found it easy to use. My site is just photo and video archive of several users, with low traffic but several gigabytes of data. What would you suggest? Is it easier to get plone working on my box and start my instance(how?), or recover the content from the instance folder(how?) and setup another content management system(which?)

  Read the article

• HP Procurve 2610 intervlan routing

  - by user19039

  Can anyone tell me why inter vlan routing is working for all vlans except my newly created vlan 4/ I have an hp procurve 2610. Any help would be appreciated. I have basically this 1 switch with all unmanaged switches attached to the core. We have a second 2610 on port 28 Running configuration: ; J9085A Configuration Editor; Created on release #R.11.25 hostname "Core_HP" interface 22 speed-duplex 100-full exit ip routing snmp-server community "public" Unrestricted vlan 1 name "DEFAULT_VLAN" untagged 1-12,17-22,26-27 ip address 192.168.4.6 255.255.255.0 tagged 25 no untagged 13-16,23-24,28 exit vlan 2 name "WAN" untagged 28 ip address 10.254.254.3 255.255.255.0 exit vlan 3 name "Wireless" untagged 13-16,24 ip address 192.168.7.6 255.255.255.0 ip helper-address 192.168.4.2 tagged 27 exit vlan 35 name "guest" untagged 23 tagged 24 exit vlan 4 name "esxi" untagged 25 ip address 10.10.1.1 255.255.248.0 exit ip route 192.168.5.0 255.255.255.0 10.254.254.1 ip route 192.168.6.0 255.255.255.0 10.254.254.1 ip route 0.0.0.0 0.0.0.0 192.168.4.10 show ip route IP Route Entries Destination Gateway VLAN Type Sub-Type M etric Dist. ------------------ --------------- ---- --------- ---------- - --------- ----- 0.0.0.0/0 192.168.4.10 1 static 1 1 10.10.0.0/21 esxi 4 connected 0 0 10.254.254.0/24 WAN 2 connected 0 0 127.0.0.0/8 reject static 0 250 127.0.0.1/32 lo0 connected 0 0 192.168.4.0/24 DEFAULT_VLAN 1 connected 0 0 192.168.5.0/24 10.254.254.1 2 static 1 1 192.168.6.0/24 10.254.254.1 2 static 1 1 192.168.7.0/24 Wireless 3 connected 0 0 show ip Internet (IP) Service IP Routing : Enabled Default TTL : 64 Arp Age : 20 VLAN | IP Config IP Address Subnet Mask Prox y ARP ------------ + ---------- --------------- --------------- ---- ----- DEFAULT_VLAN | Manual 192.168.4.6 255.255.255.0 No WAN | Manual 10.254.254.3 255.255.255.0 No Wireless | Manual 192.168.7.6 255.255.255.0 No esxi | Manual 10.10.1.1 255.255.248.0 No guest | Disabled

  Read the article

• How to stop/kill a virtual machine that hangs in "Stopping" state?

  - by SvetP

  Hi, I have a virtual machine that constantly hangs in the “Stopping” state. I’ve red several posts suggesting killing the vmwp.exe process of the machine but I’ve never been able to kill this process neither from the Windows Task Manager nor from an administrative command prompt by using prockill /PID xxxx /F where xxxx was the process ID. The only result that I have is that my machine enters in “Stopping-Critical” state. Even worse, from that point (having a virtual machine hung at stopping) I am unable to manage (stop or start) any other virtual machine on the same host. The only “solution” in that case for me is to stop the Virtual Machine Management Service (vmms.exe) and to restart the physical host. Without first stopping the vmms.exe service my physical host also hangs during the restart. Moreover, there is no any error logged in the Event Viewer. I’ve found some other posts complaining about them problem. On all of them the only suggestion was to kill the vmwp.exe process, which obviously doesn’t work for them too. Can somebody help us with this, pls? Thanks

  Read the article

• corrupted, hidden, wireless network adapter from "Network Connections" in Windows 7

  - by srihari reddy

  The issue is that when I install a wireless network adapter on my Windows 7 Professional machine I have no connectivity, the system tray icon has a red X. First, I tried the obvious, install updated drivers from the manufacturer. When I did this, the Network Connections icon had gray bars and there was no connectivity. So I tried installling the network adapter on a different computer on the same network and I verified that it does work with no issues. Next, I ran scan disk with no issues. Next, I ran sfc as admin with no issues. At this point I turned to the router and turned SSID broadcast on but that didn't help. I turned MAC address filtering off at the router but that didn't help. Whenever I installed the original network adapter (a wireless N usb adapter with WPA2 TKIP+AES) it showed up as "Wireless Network Connection 2" with a grayed out icon and no connectivity. Lastly, I tried installing two different "verified working" usb wireless adapters on to the Windows 7 Pro machine. The results were the same "Wireless Network Connection 2" that had a green bar icon but no connectivity. I installed the manufacturers software and it indicated the NIC was not there even thought the driver installed successfully in Device Manager. I guess I should mention, I first tried (insanely in vain) to use the (worthless) Windows Network troubleshooter. The results were....drumroll please... There is a problem with the network adapter... well No Duh! Also, during all of this the network adapter is always showing as "Working Properly" in the properties dialogue of Device Manager for the wireless NIC. I checked for hidden devices in Device Manager but there were none. Here is my fundamental question that I've tried to find in the Windows 7 support center with no luck. How do I remove/delete/uninstall network adapters from the Windows 7 registry? in particular hidden, corrupted network adapters, that used to be working.

  Read the article

• Bugzilla email issue

  - by xian

  My bugzilla system keep hit the following error: There was an error sending mail from '[email protected]' to '[email protected]':Can't send data I think that is some problem with my setting and configuration. First is the urlbase I have tried setting it to bugzilla.example.com, and http://127.0.0.1:81/, and http://10.0.0.236/ (My laptop IP address, I use this laptop to set up bugzilla) but the error still persists. Actually what should I put in the urlbase field? Parameter = Email Under mail_delivery_method, i choose SMTP. Under mailfrom, I put bugzilla-daemon. smtpserver, I tried leaving it blank, or setting it to 220.181.12.12 before, but could not solve my problem For my sql, the following is the data and command I used: C:\mysql\bin>mysql --user=root -p mysql Enter password: 1234 (When I install mysql into my laptop, it ask me to key an username and password, i have key in username as 'cvuser' and password as '1234', but here never ask me to key in any username) Welcome to the MySQL monitor. Commands end with ; or \g. Your MySQL connection id is 1 Server version: 5.5.15 MySQL Community Server (GPL) mysql> GRANT ALL PRIVILEGES ON bugs.* TO 'bugs'@'localhost' IDENTIFIED BY '123456'; Query OK, 0 rows affected (0.03 sec) In C:\Bugzilla\localconfig, I put the following info: # # How to access the SQL database: # $db_host = "localhost"; # where is the database? $db_port = 3306; # which port to use $db_name = "bugs"; # name of the MySQL database $db_user = "bugs"; # user to attach to the MySQL database # # Enter your database password here. It's normally advisable to specify # a password for your bugzilla database user. # If you use apostrophe (') or a backslash (\) in your password, you'll # need to escape it by preceding it with a \ character. (\') or (\\) # $db_pass = '123456'; Can someone tell me where my mistake is? I have googled for this issue for few days but still cannot find the solution.

  Read the article

• Can't login via ssh after upgrading to Ubuntu 12.10

  - by user42899

  I have an Ubuntu 12.04LTS instance on AWS EC2 and I upgraded it to 12.10 following the instructions at https://help.ubuntu.com/community/QuantalUpgrades. After upgrading I can no longer ssh into my VM. It isn't accepting my ssh key and my password is also rejected. The VM is running, reachable, and SSH is started. The problem seems to be about the authentication part. SSH has been the only way for me to access that VM. What are my options? ubuntu@alice:~$ ssh -v -i .ssh/sos.pem [email protected] OpenSSH_5.9p1 Debian-5ubuntu1, OpenSSL 1.0.1 14 Mar 2012 debug1: Reading configuration data /home/ubuntu/.ssh/config debug1: Reading configuration data /etc/ssh/ssh_config debug1: /etc/ssh/ssh_config line 19: Applying options for * debug1: Connecting to www.hostname.com [37.37.37.37] port 22. debug1: Connection established. debug1: identity file .ssh/sos.pem type -1 debug1: identity file .ssh/sos.pem-cert type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.9p1 Debian-5ubuntu1 debug1: match: OpenSSH_5.9p1 Debian-5ubuntu1 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.9p1 Debian-5ubuntu1 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-ctr hmac-md5 none debug1: kex: client->server aes128-ctr hmac-md5 none debug1: sending SSH2_MSG_KEX_ECDH_INIT debug1: expecting SSH2_MSG_KEX_ECDH_REPLY debug1: Server host key: RSA 33:33:33:33:33:33:33:33:33:33:33:33:33:33 debug1: Host '[www.hostname.com]:22' is known and matches the RSA host key. debug1: Found key in /home/ubuntu/.ssh/known_hosts:12 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: Roaming not allowed by server debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey,password debug1: Next authentication method: publickey debug1: Trying private key: .ssh/sos.pem debug1: read PEM private key done: type RSA debug1: Authentications that can continue: publickey,password debug1: Next authentication method: password [email protected]'s password: debug1: Authentications that can continue: publickey,password Permission denied, please try again.

  Read the article

• 16TB Volumes and SNMP On Windows

  - by John K

  As volumes larger than 16TB became more common, it was recognized that the 32 bit value used to report disk size and usage within the standard "HOST-RESOURCES" MIB in SNMP was not large enough to report the proper disk size. Net-SNMP seems to have addressed this issue by simply manipulating the value of "AllocationUnits" to maintain a 32 bit value for disk utilization (since total disk size/usage is equal to the 32 bit space value times the allocation unit), to allow for the calculation of a volume larger than 8/16TB. Presuming you don't have any reporting interest in the allocation unit, this seems like a fine solution. https://bugzilla.redhat.com/show_bug.cgi?id=654384 Window's built in SNMP service, however, seems to continue to suffer from this error, simply reporting the modulo of the used/assigned disk space, resulting in inaccurate disk size reporting. Is there a way to enable Windows to correctly report disk usage for volumes over 16TB? We attempted to simply install Net-SNMP 5.5 x64 and disable Windows SNMP service entirely, however this unfortunately did not fix our issue. I've seen people in the Cacti community mention simply scripting out a solution. Unfortunately, we're using Observium for quick and basic systems monitoring. If the issue can't be correct on the Window's side, can Observium be made to report custom MIBs?

  Read the article

• Which Linux distribution for vehicle LCD instrument panel

  - by Brent

  I will be designing an instrument panel for a vehicle to display the common gauges that you would find in a car - (speedometer, rpm, fuel level, oil pressure, etc.). We have selected a 7" LCD and are in the process of narrowing down the hardware (This will use an ARM processor). The idea is to read these values off of the CAN Bus and update the UI with those values. This needs to have a fairly quick boot time, 5-10 seconds would be acceptable from the time the ignigtion is turned on to the time the UI is running. I have been doing a lot of research on which linux distribution to use, but I wanted to ask the question here to get the community's suggestions. I have been a .NET programmer for years, so linux is a new world to me. Here is what I have found so far... Tizen is geared for In-Vehicle Infotainment (IVI) (plus some others). However, this project is not an IVI, and I do not need the phone dialer, navigation, etc. Meego is dead, and Tizen seems to be the replacement Angstrom, Debian... would either of these be useful? I am not tied to a particular programming language or IDE. Any help and direction is appreciated!

  Read the article

• Replacing stock Core 2 Duo heatsink fan (just the fan really) with a Dell CPU fan

  - by user647345

  My old heatsink fan broke and I'm trying to reconnect its plugs to a new fan. My Dell CPU fan has some custom Dell plug. I snipped the old fan's wire in half and kept the plug on the end of it. I want to connect it to the Dell fan wire to the plug. The motherboard is a P5Q-e, the stock Core 2 Duo fan was .20A and the dell is .70A. Is that going to matter? The wire from the fan has four wires, the wire with the plug has four wires. They share three, of the four colors: red, black, and blue. Dell's fourth wire is white, while the plug's fourth wire is yellow. Is it safe to assume that I just connect the yellow and the white plug together and match the rest up? I don't want to take any risk of damaging anything. It runs fine passively without a fan, but I have speedstep on, so I would like to use this fan and just fasten it to the heatsink with some twist ties and paperclips and call it a day.

  Read the article

< Previous Page | 309 310 311 312 313 314 315 316 317 318 319 320  | Next Page >