Search Results

Search found 8923 results on 357 pages for 'wireless keyboard'.

Page 327/357 | < Previous Page | 323 324 325 326 327 328 329 330 331 332 333 334  | Next Page >

• IPSec tunnelling with ISA Server 2000...

  - by Izhido

  Believe it or not, our corporate network still uses ISA Server 2000 (in a Windows Server 2003 machine) to enable / control Internet access to / from it. I was asked recently to configure that ISA Server to create a site-to-site VPN for a new branch in a office about 25 km. away from it. The idea is basically to enable not only computers, but also Palm devices (WiFi-enabled, of course), to be able to see other computers in both sites. I was also told that a simple VPN-enabled wireless AP/router (in this case, a Cisco WRV210 unit) should be enough to establish communications with the main office. To be fair, the router looks easy to configure; it was confusing at first, but further understanding of how site-to-site VPNs work cleared all doubts about it. Now I need to make modifications to our ISA Server in order to recognize the newly installed & configured "remote" VPN site. Thing is, either my Googling skills are pathethically horrible, or there doesn't seem to be much (or any, at all) information about how to configure an ISA Server 2000 for this purpose. Lots of stuff on 2004, of course; also, I think I saw something for 2006. But nothing I could find about 2000. Reading about 2004, it seems that the only way I can do site-on-site with a Cisco router (read: a non-ISA-Server machine) is through something they call a "IPSec tunnel". Fair enough. However, I can't figure for the life of me how could I even start to find, leave alone configure, such a thing. Do you, people, happen to know how to do IPSec tunelling on a ISA Server 2000, so I can connect to a Cisco WRV210 VPN-enabled router, and build a site-to-site VPN for both networks? Or is this not possible at all? (Meaning I should change anything in this configuration to make it work...)

  Read the article

• Ubuntu NBR karmic boot freezes at fsck from util-linux-ng 2.16

  - by Bluebill

  I have a netbook (emachine e250 - equivalent to an acer aspire one) and I have Ubunutu NBR 9.10 installed on it. Every other cold boot freezes at the following error message: fsck from util-linux-ng 2.16 There is no disk activity, no activity what so ever. I have left the machine sit for over an hour and nothing. It takes a couple of hard resets to be able to boot properly. Once it boots everything works great (wireless, suspend/resume, etc.)! I have spent the last couple of weeks researching the problem and the only thing that seems to work is setting nolapic in the boot string in grub - it boots every time. Unfortunately, nolapic disables the second core and causes problems with suspend resume. At first I thought it was an fsck problem with the first partition on the hard disk as it is a hidden ntfs partition containing the windows xp recover information. So in /etc/fstab I set the partition so that it would be ignored by fsck. This didn't seem to do anything. I have these partitions: /dev/sda1 - an ntfs recovery partition /dev/sda2 - /boot /dev/sda3 - swap /dev/sda5 - / /dev/sda6 - /home I am running kernel version 2.6.31-19-generic and have all the patches (as indicated by update manager). I also have no splash screen so I can see the boot progress. I have only been using NBR since January, I have been using Ubuntu on my desktop since last June (2009-06). What logs should I be looking at? Is there a log for failed boots?

  Read the article

• Finding useful crash-information in Windows 8 Consumer Preview

  - by Lukas Knuth

  I'm currently diving into C# and wanted to play around with the new Metro-styled-applications introduced with Windows 8, so I updated my Windows 7 to Windows 8 Consumer Preview. The problem I'm facing right now is, that the system freezes after 3-5 minutes. It does not take any input from the keyboard or mouse and it does not recover (at least not in less then 10 minutes). Since I have a background in Linux, I'd like to find some information about the cause of the freeze, but I have no idea where to search. I checked the system-logs (under "System Control" - "Management") but they only record that the system was shut down unexpectedly (doe to the face that I held down the power-button to reboot the PC). There is no useful crash-information in there. I don't want to spend hours on randomly reinstalling drivers and doing things that "might help". Isn't there any place I can find some useful information about the freeze? Before you ask: I installed Windows 8 as an updated on my old Windows 7 installation (which worked fine by the way). My hardware fits the minimum requirements (specs can be found here, the MacMini 3,1 model with 2GHz processor). I have updated the graphics-card drivers to the newest Windows 8 drivers from nVidia.

  Read the article

• Can't ping through default gateway

  - by Andrew G.H.

  I have the following configuration: Routing table on M3 is: Destination Gateway Genmask Flags MSS Window irtt Iface 0.0.0.0 192.168.2.1 0.0.0.0 UG 0 0 0 eth1 192.168.2.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 192.168.3.0 0.0.0.0 255.255.255.192 U 0 0 0 eth0 Routing table on M1 is: Destination Gateway Genmask Flags MSS Window irtt Iface 0.0.0.0 192.168.0.1 0.0.0.0 UG 0 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth1 192.168.0.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 192.168.2.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 So basically M3's gateway is M1, and M1's gateway is M2's wireless internet interface. If I ping 8.8.8.8 from M1, everything is ok, replies are received. Pinging from M1 to M3 and viceversa is also possible. I have configured M1 as gateway trafic forwarder using firestarter package and stopped firewall with it. iptables policies are ACCEPT for everything. Problem: I have tried ping-ing ip 8.8.8.8 from M3 but without success. What could be the source of this problem?

  Read the article

• iptables secure squid proxy

  - by Lytithwyn

  I have a setup where my incoming internet connection feeds into a squid proxy/caching server, and from there into my local wireless router. On the wan side of the proxy server, I have eth0 with address 208.78.∗∗∗.∗∗∗ On the lan side of the proxy server, I have eth1 with address 192.168.2.1 Traffic from my lan gets forwarded through the proxy transparently to the internet via the following rules. Note that traffic from the squid server itself is also routed through the proxy/cache, and this is on purpose: # iptables forwarding iptables -A FORWARD -i eth1 -o eth0 -s 192.168.2.0/24 -m state --state NEW -j ACCEPT iptables -A FORWARD -m state --state ESTABLISHED,RELATED -j ACCEPT iptables -A POSTROUTING -t nat -j MASQUERADE # iptables for squid transparent proxy iptables -t nat -A PREROUTING -i eth1 -p tcp --dport 80 -j DNAT --to 192.168.2.1:3128 iptables -t nat -A PREROUTING -i eth0 -p tcp --dport 80 -j REDIRECT --to-port 3128 How can I set up iptables to block any connections made to my server from the outside, while not blocking anything initiated from the inside? I have tried doing: iptables -A INPUT -i eth0 -s 192.168.2.0/24 -j ACCEPT iptables -A INPUT -i eth0 -j REJECT But this blocks everything. I have also tried reversing the order of those commands in case I got that part wrong, but that didn't help. I guess I don't fully understand everything about iptables. Any ideas?

  Read the article

• How to troubleshoot when one has no idea where to start?

  - by Chris Walton

  I am looking for hints, tips and answers on how to get started on troubleshooting when: The problem is intermittent The problem could lie literally anywhere - operating system; free source software; my own software developments; purchased software; crumbs on the keyboard; the specific combination of software I am currently running; Maxwell's demon; the little blue men actually running the machine have gone on strike; etc. I have expertise only in a few of the areas that are potential candidates for the cause of the problem. The specific problem I am having is detailed below as an example, but I am not seeking answers to my current problem, but rather where and how to start on tackling such problems. I am currently encountering a problem with my new machine. On a few occasions the machine has just frozen; not accepting keystrokes, mouseclicks, or anything except the power on/off switch. Invariably I have been merely browsing the web; I have had a few (<= 6 other applications) running. None of these applications are major; and represent a mix of commercial programs and open source programs, typically migrated from Unix of some variety. My machine is a Windows 7 I7 quad core laptop.

  Read the article

• grep --color=auto with -i option disables the matching text color, why?

  - by emptyset

  I was messing around with grep and put this in my .zshenv: export GREP_OPTIONS="--color=auto" export GREP_COLORS='mt=1;34' I was bonking my head on the keyboard and changing GREP_COLORS around for a minute trying to figure out why the folder colors were working, but the matching text wasn't. I was doing this: $ grep -R -n -i -e "functionFoo\(" --include=*.cs --exclude-dir=Logs * The line number and file names were set with the default colors, but the matching text wasn't. After spending way too much time, I thought to do this: $ grep -R -n -e "functionFoo\(" --include=*.cs --exclude-dir=Logs * (I removed the -i option.) That's all it took to get the matching text to correctly show up in bold blue. This is a Cygwin on Vista setup, with rxvt running zsh. Any idea why grep colors would break on specifying a case-insensitive match? Update: Under cygwin 1.7, it's a little bit better - case insensitive search works correctly, but it only highlights the word that matches the expression exactly. In other words, "FunctionFoo" highlights "FunctionFoo" but not "functionFoo" and vice versa. Probably a grep issue so I'll be submitting it to that list.

  Read the article

• What are some of the best answer file settings for a WDS Deployment?

  - by drpcken

  I've had my head buried in answer files for days now and have gotten quite comfortable setting them up, test, etc... I use a handful of Components to help my migrations, for my unattend.xml I like: Windows-International-Core-WinPE -- this is good for setting Locales the preboot environment (en-us for us english US speakers). Keeps me from having to set these on the initial image boot. Windows-Setup_neutral -- I like the WindowsDeploymentServices -> ImageSelection, especially if I'm only pushing a single image. This keeps me from having to select it each time. My OOBE_Unattend.xml is really useful and I barely have to touch anything during this part of the installation: Windows-Shell-Setup_neutral -- This lets me put a ProductKey in for my MAK volume license (very useful and time saving). I can also set the TimeZone for the installation. Windows UnattendedJoin_neutral -- I couldn't live without this component. It joins the machine on my domain before logging in as a domain administrator. I would hate to not have this ability. Windows-International-Core -- Again this component really speeds up the OOBE process. I configure my locals and time zone so I don't have to do it by hand when the machine enteres OOBE. Windows-Shell-Setup -- Allows you to configure an autologon when the new machine is finished. I like to logon as a domain admin automatically for customizing and troubleshooting the new machine immediately after it is imaged. Also the OOBE component under here lets me skip the EULA, Hide Wireless Setup, and set my default NetworkLocation. All of this makes the entire OOBE totally automated. What are some other good components I am missing as far as helping me get these images pushed and configured as quickly as possible?

  Read the article

• Extremely Weird Computer Problem

  - by waiwai933

  Well, having worked with computers a long time, I thought I had seen everything that could go wrong with a computer. Today, I learned that I was wrong. My Mac has been behaving extremely weirdly. While the keyboard is fine, the mouse holds extremely weird behavior. It will open apps from the Dock, but not open documents from a Stack. The top menu bar will work, but only after I restart Finder. I am unable to close most windows, except with Cmd+Q. Clicking on a link in Safari, for some reason, opens it in a new tab. I can not select checkboxes, but I know a click is going through because you can see a quick indent in the check box, before it reverts to the unchecked state. I've restarted my computer, as well. I don't see a virus when looking through top, but I guess it could be subverting top. Does anyone have an idea what is going on?

  Read the article

• Disable CTRL+mouse wheel zooming in Chrome?

  - by Peter Nore

  I'm a normal-sighted person and I would like to view pages at 100% all the time. I use keyboard shortcuts that involve CTRL a lot, so about twenty times a day I accidentally hit CTRL at the same time that I'm scrolling, which results in the page being reflowed and repainted. This in is annoying because it can take up to 30 seconds to fix the issue, depending on how complex the site layout is. On sites with dynamic layout such as Google Docs the problem is more serious; accidentally hitting CTRL+mouse wheel corrupts the display and forces me to refresh the page entirely, sometimes causing me to loose information in the process. I would like to either decouple CTRL+mouse wheel from zoom, or disable zoom functionality altogether. This is possible on Firefox by using about:config; is there a similar way to edit detailed settings in Chrome? Would I have access to the detailed settings if I used Chromium instead of Chrome? I'll probably jump ship back to Firefox if I can't solve this problem. There is a superuser question that asks basically the same thing I'm asking, but for Firefox and Internet Explorer exclusively. Other people on the Chrome forum have had related issues, but none have the same problem. "I would really like it if I could deactivate the auto zoom in/out." had "something with laptops and Windows 7", not the feature built into Chrome. Other people have had PDF specific issues, which doesn't concern me. I've also tried searching for extensions that allow you to disable the scroll; I had hoped that "Zoom Lock" would have the ability to lock the zoom at 100% and prevent CTRL+scroll wheel from distorting the display, but it doesn't work for my use case. Google Chrome version 9.0.597.84 (Official Build 72991) Operating System: Ubuntu 10.10

  Read the article

• Free software for backing up an attached network drive

  - by Richard

  My wireless router comes with a USB connector which allows me to plug an external hard drive in and it'll act as a Network Attached Storage. The problem is that I want to backup this hard-drive to the external drive of another computer so that if the NAS drive fails, I don't lose everything. However, Windows 7 Backup refuses to include the NAS as a location to backup. I can't fool it by mapping it to a drive letter either. Google presents lots of pages on how to backup files to a NAS, but not the other way around. Can anyone advise me on free software which can do incremental backups of a NAS drive to an external drive attached the computer it is running on? I'm aware of this question but the top answers have one or more of the following issues: They aren't free. The free version cannot backup a NAS. They cannot do incremental backups. They're just a script and therefore have limited other functionality (eg. disk space management, scheduling, compression, etc.etc.)

  Read the article

• How do I clear out the ssh-agent entries (on Mac OS X )?

  - by cwd

  I'm running Mac OS X, and it appears that after SSHing to several machines, using identity files, my 'ssh-agent' builds up a lot of identity / keys and then sometimes offers too many to a remote machine, causing them to kick me off before connecting: Received disconnect from 10.12.10.16: 2: Too many authentication failures for cwd It's pretty obvious what's happening, and this page talks about it in more detail: SSH servers only allow you to attempt to authenticate a certain number of times. Each failed password attempt, each failed pubkey/identity that is offered, etc, take up one of these attempts. If you have a lot of SSH keys in your agent, you may find that an SSH server may kick you out before allowing you to attempt password authentication at all. If this is the case, there are a few different workarounds. Rebooting clears the agent and then everything works OK again. I can also add this line to my .ssh/config file to force it to use password authentication: PreferredAuthentications keyboard-interactive,password Anyhow, I saw the note on the page I referenced talking about deleting keys from the agent, but I'm not sure if that applies on a Mac since they appear to be cleared after reboot anyhow. Is there a simple way to clear out all keys in the 'ssh-agent' (the same thing that happens at reboot)?

  Read the article

• How do I diagnose the cause of a freeze after resuming in Windows XP (SP3)?

  - by Software Monkey

  I have just built a new computer from parts. Whenever I resume from any sleep mode (S1, S3 or S4) the computer freezes within about 60 seconds of the welcome screen appearing. I have updated the BIOS and all drivers to current from the motherboard manufacturer's site. I have reset BIOS settings to default, including disabling AMD Cool n Quiet. The windows event logs are not helpful at all. Other than immediately after resuming the system is stable as long as AMD CnQ is disabled. The system is: Mobo : MSI 790GX-G65 CPU : AMD Phenom II 965 BE at 3.6 GHz Memory : Corsair DDR3 1600, at 1333 MHz and 9-9-9-21 HDDs : 1 EIDE, 2 SATA in RAID-0 DVD : 1 Card Reader: 1 multi-card reader Keyboard is attached via PS2 and mouse is USB. Any thoughts or pointers would be most welcome. EDIT: It appears that the computer may not freeze if a program is left running which puts it under significant load. I left a stress test running which keeps all cores under 85% load, and my son put the computer to sleep - while this program is running it I have been able to resume from S3 successfully 4 times, compared against about 20 tests with the computer idle which have all frozen. So this may be related to being in an idle state when it resumes.

  Read the article

• What was your biggest waste of money, and what should you have bought instead? [closed]

  - by rob

  I waste a lot of money on computer equipment and other electronics that I don't really need. I've also bought software that I've never really used, or which as been replaced by better free software. As I'm buying things, it doesn't seem like much--fifty bucks here, a hundred dollars there. But when I go back and look at how much I've spent over my past few electronics purchases, I usually start to think of the other things I could have bought with that money instead. Most of the computer hardware and electronics don't usually improve my life by much, if at all. Case in point: back when I was in college, I prided myself on getting the best deals for computer hardware, but when I went back and added up all the money I had spent, I had probably wasted close to a thousand dollars on "cheap" $100 hard drives that eventually all went bad (including the warranty replacements). Even if they did still work, it would not be worth the effort to use them, because they're too small and too noisy by today's standards. I've also spent thousands more on other junk, such as RAM and CPU upgrades that only gave modest performance jumps, and wireless audio transmitters that I used for a short time to stream music from the now-defunct Yahoo! Music service. Every time I see a really great deal on RAM or video cards, I come one click away from buying them, but these days I'm usually able to resist. I've been wanting to get into woodworking ever since I moved into my house, and five years later I'm finally saving up for a $600 table saw. Sure, I've already got a toolbox and a couple of the essential power tools like a drill and a jigsaw, but I can't help but think that I'd have an entire shop full of woodworking tools and a lot of nice wood furniture if I hadn't wasted all that money back in college. What has been your biggest waste of money on computer stuff and technology? If you had all that money back, would you make the same mistake again and buy the same types of things, or would you spend it on something else?

  Read the article

• SSH connection problem - allowed from LAN but not WAN

  - by Kerem Ulutas

  I tried to setup my Arch Linux installation to be an SSH host, but here is the thing: I can ssh localhost, it fails to login via public key and asks for username and password, but still able to login. When I try ssh my_wan_ip it gives ssh_exchange_identification: Connection closed by remote host error. I've read all topics about this error and none helped me. By the way, just confirmed, it gives ssh: connect to host my_dyndns_hostname port 22: Connection refused from another machine (outside of my network, it has different wan ip). I have sshd: ALL in "hosts.allow", ALL:ALL in "hosts.deny". I am able to connect to my own pc via ssh, ping my own pc, but my ssh setup seems to be the problem, it gives that annoying error when I try to ssh from wan. /etc/ssh/ssh_config /etc/ssh/sshd_config And finally, here is the debug output for both sshd and ssh: (i ran ssh command and i took output to sshd debug after that): sshd debug ssh debug I can edit my question according to your needs. Just ask for any more information needed. BTW I have no iptables running. I have one cable dsl modem connected to a asus wl-330gE wireless access point, they both have their firewall disabled. I configured NAT so port 22 is directed to the pc I'm having this trouble. Any help appreciated, thanks..

  Read the article

• how could application installations/configurations be easier in linux?

  - by ajsie

  although you can do anything in linux it tends to require a lot of tweaking in config files and reading a lot of manuals/tutorials before you can have it running in your way. i know that it gets a lot easier by time, and the apt-get installations with ubuntu/debian is heading the right way. but how can linux be more userfriendly for us in the future? i thought that if more is automated like an IDE environment, eg. typing svn will give us all the commands and description about each command when you move between commands with your keyboard. that would be great. but that's just one example. another is the navigation in the terminal between folders. now you have to type a lot just to jump from/to different folders. would be great with some more automatization here too. i know that these extra features will slow down the server, but its 2010 now, and these features are not that heavy for the cpu, but makes it more userfriendly and encourage maintainance of a server, not frighten u off. what do you think about this? should/could we have more user friendly linux environment in servers, something that has annoyed you a lot? a lot of things are done in the unix way, but maybe we should reinvent the wheel in some areas, cause apparently, its so...repeatingly today and difficult to do easy tasks. it should be easier i think..

  Read the article

• SSH session becomes unresponsive when logged into Ubuntu Server virtual machine using VirtualBox

  - by nickbart

  Hi everyone, I'm really at my wits end here, so I'm hoping someone here can help me. I have a virtual machine running Ubuntu Server 9.10. It's just a small development environment so I can keep my code separate from the test and production environments. I am running it through VirtualBox 3.1.6 on a laptop running Ubuntu Desktop 9.10. I have it set up with a bridged network connection and it is bridged to my laptop's wireless adapter. We have no wired connections in this office. I boot up the VM and everything is fine. I can SSH into it using gnome-terminal and for a while everything is Kosher. Then seemingly randomly, the SSH terminal session with hang. No error message, nothing; it just becomes unresponsive. If I go to the VirtualBox terminal I find the VM itself is perfectly fine. It can ping and I can SSH out with it. If I restart the networking on the VM the SSH session in my gnome-terminal will most of the time become responsive again. Here's an interesting point, the SSH session will sometimes die right in the middle of me typing something (this points to it not being an idle session issue) and if I go to the VirtualBox terminal and restart the networking and then return to my gnome-terminal SSH session I find that it will come back to life and what I typed when the session hung originally will magically type itself in to the buffer. So, my input is getting stored somewhere and just can't make its way to the VM until the networking on the VM is restarted. I've tried different versions of VirtualBox and used vmdk images and vdi images and nothing seems to work. I can't tell if the problem is with my laptop, VirtualBox, or the Ubuntu Server VDI. Is there anyway to debug this issue? Or has anyone out there seen anything similar? Your help is much appreciated. Nick

  Read the article

• using a second computer as a mere screen/monitor in X (VNC?)

  - by lara michaels

  Hello My goal is to use three monitors with my Linux system. It is a laptop, so adding another video card is not the easiest solution. (I have investigated a number of such options: getting a docking station with a PCI slot, USB/Cardbus vga adapters, etc, and for the time being don't want to go that way.) I am wondering if using an older desktop+screen I have lying around as the third "monitor" might be the easiest solution, if only there is a way to get it to work as a seamless, integrated desktop. I was wondering if I can use VNC or perhaps X itself (?) to achieve the following: computer A is my main computer; it has all my files, etc. computer B is used just to display on an additional screen keyboard+mouse are connected to computer A use VNC or X to connect the two so that computer B shows a X screen that is just as if it was a third physical screen connected to computer A. I don't know if the last point is clear, but what I mean is that I would like to be able to: be able to have my window manager assign/move around virtual desktops on all three screens move windows back and forth between the screens attached to computer A and the screen of computer B be able to copy something in an app being shown on a screen of computer A and paste it into an app being shown on the screen attached to computer B access the filesystem on my main computer (A) when using applications that are being shown on the screen attached to computer B Basically, I would like X to treat computer B just like it was nothing but a third physical screen... Is this doable? : ) ~lara

  Read the article

• How do I stop VLC from stealing my volume buttons

  - by MGOwen

  when I press the volume buttons on my laptop, usually the system volume is changed. However, when I do this with VLC it "steals" the presses and adjusts it's own "volume" instead. The system volume is also changed. I can't find any way to turn this off in VLC. Does anyone know? Update: Sorry, some more details I should have included originally: VLC VERSION: 1.1.4 (and a few previous releases, back to about 1.1.0 or so, I think) OS: Win Vista Pro 32 HARDWARE: Dell 1720 laptop (the volume buttons are little buttons on the front of the unit, they may work something like "media" keyboard volume buttons) Update: The buttons seem to map to Ctrl+Alt+b and Ctrl+Alt+c (according to the shortcut key box in windows shortcut properties) but the VLC advanced preferences hotkeys screen doesn't list these as the keys it uses for volume. I changed it so there are no volume hotkeys in VLC settings - no luck it still steals the presses and adjusts the volume. Also, pressing Ctrl+Alt+b or c doesn't change my system volume, so who knows what windows or VLC are doing to recognise those volume buttons. :(

  Read the article

• can't ssh from mac to windows (running ssh server on cygwin)

  - by Denise

  I set up an ssh server on a fresh windows 7 machine using the latest version of cygwin. Disabled the firewall. I can ssh into it from itself, from a different windows box (using winssh), and from a linux vm. In spite of that, I tried to ssh in from two different macs, and neither would let me! This is the debug output: OpenSSH_5.1p1, OpenSSL 0.9.7l 28 Sep 2006 debug1: Reading configuration data /etc/ssh_config debug1: Connecting to 3dbuild [172.18.4.219] port 22. debug1: Connection established. debug1: identity file /Users/Denise/.ssh/identity type -1 debug1: identity file /Users/Denise/.ssh/id_rsa type 1 debug1: identity file /Users/Denise/.ssh/id_dsa type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.5 debug1: match: OpenSSH_5.5 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.1 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-cbc hmac-md5 none debug1: kex: client->server aes128-cbc hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Host '3dbuild' is known and matches the RSA host key. debug1: Found key in /Users/Denise/.ssh/known_hosts:43 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey,password,keyboard-interactive debug1: Next authentication method: publickey debug1: Trying private key: /Users/Denise/.ssh/identity debug1: Offering public key: /Users/Denise/.ssh/id_rsa Connection closed by [ip] It shows the same output, and fails at the same place, whether I have put my public key on the ssh server or not. Any help would be appreciated-- hopefully someone has run into this before?

  Read the article

• How do I access my samba drive through several layers of network topology?

  - by stephenmm

  I have a new windows 7 Home Premium machine that is in a different room than my main computer area. As such I have to use a bridge and another router. Everything is working wonderfully except I cannot access the SAMBA drive with the new machine. I know that SAMBA is accessible as an older WinXP machine can access it. A picture of my network would probably be helpfull: To ISP | | +---------------------------+ | WAN | | Cable Modem | | (2WIRE678) | | | | | +---------------------------+ | +---------------------------+ | | (|) (|) +-----------+ | Belkin Router | | | | Wireless | | (F5D) |--+ +--| WinXP | | | |SAMBA USER | | | +-----------+ +---------------------------+ | | | | +------------+ | | Ubuntu | | | Apache + | | |SAMBA Server| | +------------+ | | +---------------------------+ | | | Netgear Bridge | | (XET1001) | | | +---------------------------+ # # +---------------------------+ | | | Netgear Bridge | | (XET1001) | | | +---------------------------+ | +---------------------------+ | | | D-Link Router | | (DI-524) | | | | | +---------------------------+ | | | | +-----------+ | | | Win7 | |SAMBA USER?| +-----------+ More interesting data points: 1. I can ping the SAMBA server from the Win7 machine locally (Ie. 192.168.2.2) 2. I can access the webserver from the Win7 machine locally (Ie. 192.168.2.2) 3. I followed the advice to get Win7 and SAMBA to play nice: http://www.tannerwilliamson.com/2009/09/windows-7-seven-network-file-sharing-fix-samba-smb/ Sorry for being so long winded but it is kind of complex and I am really at a loss as to how to fix it. If any of you have some suggestions I would love to hear it!

  Read the article

• Laptop Randomly Turning On and Off

  - by Ian Mallett

  So, I have a pretty new laptop, and one of its quirks is that, at random times (though typically in the middle of the night), it seems to wake up from sleep mode, churn a bit, and then go back into sleep mode. I write "seems" because its fans are very loud, so it's obvious when it's not asleep, but during the time it is "on", I can't see anything on the screen. I have researched the problem somewhat, and could only find similar issues; nothing identical. In those cases, it appeared that certain devices could be responsible. Nothing is plugged into my computer during this behavior, but I nonetheless disabled every device's permission to wake the computer through the device manager. This included disabling the magic packet wake for the network (despite its only having a wireless connection). Using "powercfg /lastwake" gives an empty wake history. But, I also went through all the tasks and checked if they would wake the computer. None appeared to. The problem persisted, so, after some more research, I found this, and executed it for all power schemes on the computer. The problem persists. System: OS: Windows 7 Professional CPU: Intel 990X GPU: NVIDIA GeForce 580M/12GB RAM Motherboard: Clevo X7200 Model: NP7282-S1 (Sager-built laptop)

  Read the article

• Setting up a network where packets are traced

  - by Marcus

  My situation is the following: I have an internet connection, which is shared between people. More or less obviously, people is using it to download illegal stuff. Since I'm the owner of the connection, I want to avoid being sued. I don't want to prevent the people from doing the things they want, but I want to be legally safe. Now, I have relatively little competences in network administration, so I was wondering: is it possible to setup a network, where the source and destination of the packets are logged? I would use this to prove, in case of lawsuit, that the traffic was coming from a given machine. if the idea is feasible, is there any wireless router on which I can install linux, where I can install the packet sniffer? how much space could the logs take (containing only the timestamp/source/destination), per GB of traffic? a very rough estimation would be very helpful. if a machine on my network is sending bittorrent packets to a certain IP, would this log be able to reflect the time, source ip and destination ip? I assume that obviously the torrent data would be encrypted and un-decryptable. Am I missing something? Is there a better strategy? Any pointer to documentation would be helpful as well - in that case, I would use this as starting point.

  Read the article

• Docking Station Sound Doesn't Work on Dell D830 with Windows 7

  - by cisellis

  I have a Dell Latitude D830 laptop that is running Windows 7 Enterprise x64. I connect to a docking station during the day with multiple monitors, a keyboard and a mouse. Everything runs with no problems including most of the docking station ports (usb, monitors, etc.) However, the sound port from the docking station does not work since the upgrade to Windows-7. Even with the laptop plugged in, the sound always comes out of the laptop, not the headphones plugged into the docking station. Here's what I've tried: I've seen other issues like via Google this that seem to be mostly unanswered. I found one or two that referenced using the Vista x64 drivers, especially the Nvidia drivers. I do not have an Nvidia chipset but I've reinstalled the sound drivers and that has not helped. I don't have a support contract and considering the cost is usually high to call Dell, that's not an option. Dell's forums are pretty much a wasteland and I've found no help there. Since this is a docking station I thought I might need to try the SATA or Intel chipset drivers from the dell site instead, however I'm not really sure and I need to work on this laptop in the meantime. I can't really afford the downtime to experiment with random drivers all day in case they turn out to be incompatible (Dell still hasn't added Windows 7 to their support site as far as I can tell). Does anyone have any other ideas? Has anyone had this issue and solved it? If so, how? Thanks in advance for your help.

  Read the article

• Port 22 is not responding

  - by Emanuele Feliziani

  I'm trying to make the jump to VPS from shared hosting for better performances and greater flexibility, but am stuck with the fact that I can't access the machine via ssh. First of all, the machine is a CentOS 6.3 cPanel x64 with WHM 11.38.0. Sshd is running (it appears in the current running processes). Making a port scan I see that port 22 is not responding. Port 21 is, but I am not able to access the machine via ftp (I think it's a security measure, but I don't know where to disable/enable it). So, I'm stuck in WHM and have no way to access the configuration of the machine, neither via ssh nor with ftp/sftp. When trying to connect with ssh via Terminal I only get this: ssh: connect to host xx.xx.xxx.xxx port 22: Operation timed out I also tried to access with the hostname instead of the IP address and it's the same. There seem to be no firewall in WHM and I have whitelisted my home IP address to access ssh, though there were no restrictions in the first place. I have been wandering through all the settings and options in WHM for several hours now, but can't seem to find anything. Does anybody have a clue as to where I should start investigating? Update: Thanks everyone. It was in fact a matter of firewall. There was a firewall not controlled by the WHM software. I managed to crack into the console from the vps control panel (a terrible, terrible java app that barely took my keyboard input) and disabled the firewall altogether running service iptables stop so that I was able to access the console via ssh with the terminal. Now I will have to set up the firewall again because the command I ran looks like having completely wiped the iptables. Can you recommend any newby-friendly resource where I can learn how to go about this and what should I block? Or should I just go with something like this: http://configserver.com/cp/csf.html ? Thanks again to everyone who helped me out.

  Read the article

< Previous Page | 323 324 325 326 327 328 329 330 331 332 333 334  | Next Page >