Search Results

Search found 16764 results on 671 pages for 'provider model'.

Page 333/671 | < Previous Page | 329 330 331 332 333 334 335 336 337 338 339 340  | Next Page >

  • Best Processor for MediaSmart Server?

    - by Kent Boogaart
    I'm trying to figure out what the best possible processor is that I can stick in my HP MediaSmart server. I'm clueless when it comes to correlating CPUs to motherboards. I suspect it's the socket type I care about, but I worry that there's more to it. CPU-Z gives me (excerpt): Processors Information ------------------------------------------------------------------------- Processor 1 ID = 0 Number of cores 1 (max 1) Number of threads 1 (max 1) Name AMD Sempron LE-1150 Codename Sparta Specification AMD Sempron(tm) Processor LE-1150 Package Socket AM2 (940) CPUID F.F.1 Extended CPUID F.7F Brand ID 1 Core Stepping DH-G1 Technology 65 nm Core Speed 1000.0 MHz Multiplier x FSB 5.0 x 200.0 MHz HT Link speed 800.0 MHz Stock frequency 2000 MHz Instructions sets MMX (+), 3DNow! (+), SSE, SSE2, SSE3, x86-64 L1 Data cache 64 KBytes, 2-way set associative, 64-byte line size L1 Instruction cache 64 KBytes, 2-way set associative, 64-byte line size L2 cache 256 KBytes, 16-way set associative, 64-byte line size FID/VID Control yes Max FID 10.0x Max VID 1.350 V P-State FID 0x2 - VID 0x12 (5.0x - 1.100 V) P-State FID 0xA - VID 0x0C (9.0x - 1.250 V) P-State FID 0xC - VID 0x0A (10.0x - 1.300 V) K8 Thermal sensor yes K8 Revision ID 6.0 Attached device PCI device at bus 0, device 24, function 0 Attached device PCI device at bus 0, device 24, function 1 Attached device PCI device at bus 0, device 24, function 2 Attached device PCI device at bus 0, device 24, function 3 Chipset ------------------------------------------------------------------------- Northbridge SiS 761GX rev. 02 Southbridge SiS 966 rev. 59 Graphic Interface AGP AGP Revision 3.0 AGP Transfer Rate 8x AGP SBA supported, enabled Memory Type DDR2 Memory Size 2048 MBytes Channels Single Memory Frequency 200.0 MHz (CPU/5) CAS# latency (CL) 5.0 RAS# to CAS# delay (tRCD) 5 RAS# Precharge (tRP) 5 Cycle Time (tRAS) 15 Bank Cycle Time (tRC) 21 Command Rate (CR) 1T DMI ------------------------------------------------------------------------- DMI BIOS vendor Phoenix Technologies, LTD version R03 date 05/08/2008 DMI System Information manufacturer HP product MediaSmart Server version unknown serial CN68330DGH UUID A482007B-B0CC7593-DD11736A-407B7067 DMI Baseboard vendor Wistron model SJD4 revision A.0 serial unknown DMI System Enclosure manufacturer HP chassis type Desktop chassis serial unknown DMI Processor manufacturer AMD model AMD Sempron(tm) Processor LE-1150 clock speed 2000.0 MHz FSB speed 200.0 MHz multiplier 10.0x DMI Memory Controller correction 64-bit ECC Max module size 4096 MBytes DMI Memory Module designation A0 size 2048 MBytes (double bank) DMI Memory Module designation A1 DMI Memory Module designation A2 DMI Memory Module designation A3 DMI Port Connector designation PS/2 Mouse (internal) port type Mouse Port connector PS/2 connector PS/2 DMI Port Connector designation USB0 (external) port type USB DMI Physical Memory Array location Motherboard usage System Memory correction None max capacity 16384 MBytes max# of devices 4 DMI Memory Device designation A0 format DIMM type unknown total width 64 bits data width 64 bits size 2048 MBytes DMI Memory Device designation A1 format DIMM type unknown total width 64 bits data width 64 bits DMI Memory Device designation A2 format DIMM type unknown total width 64 bits data width 64 bits DMI Memory Device designation A3 format DIMM type unknown total width 64 bits data width 64 bits How do I figure out what options I have for an upgrade?

    Read the article

  • Rocketfish Driver

    - by darthg8r
    I've got a RocketFish SATA enclosure, model number RF-AHD35. It has a card reader on it. Windows doesn't see the card reader. I figure it's a driver problem. But, I don't have the CD that came with it anymore, nor is it available from their site. As a matter of fact, their site looks like my 8 year old made it. Does anyone have access to this driver?

    Read the article

  • cherrypy fails to stop when puppet tries to ensure running and refresh it at the same time

    - by ento
    I am trying to manage a cherrypy service with puppet. However, when the configuration is applied, cherryd ends up with no PID file although the process is up and running. Since the PID file is lost I can no longer stop the process with /etc/init.d/mycherryd stop (unless I modify the handmade init script to lookup the PID with ps or something.) $ /etc/init.d/mycherryd status cherryd dead but subsys locked The problem seems to be that puppet is trying to refresh/restart cherryd (triggered by changes in configuration files) immediately after ensuring it's running (as specified in the manifest), and cherrypy fails to stop and start (restart) itself while still executing its startup process. Is there a clear cut solution to this problem? Is this a bug on the cherrypy side, or can I write a puppet manifest so refresh is called only after the service is up and running? Any suggestion welcome. cherrypy log See how cherrypy catches SIGTERM midway through startup and still starts to listen. :cherrypy.error[18666] 2010-02-12 13:10:23,551 INFO: ENGINE Listening for SIGHUP. :cherrypy.error[18666] 2010-02-12 13:10:23,552 INFO: ENGINE Listening for SIGTERM. :cherrypy.error[18666] 2010-02-12 13:10:23,552 INFO: ENGINE Listening for SIGUSR1. :cherrypy.error[18666] 2010-02-12 13:10:23,552 INFO: ENGINE Bus STARTING :cherrypy.error[18671] 2010-02-12 13:10:23,554 INFO: ENGINE Daemonized to PID: 18671 :cherrypy.error[18671] 2010-02-12 13:10:23,554 INFO: ENGINE PID 18671 written to '/var/mycherryd/cherry.pid'. :cherrypy.error[18671] 2010-02-12 13:10:23,555 INFO: ENGINE Started monitor thread '_TimeoutMonitor'. :cherrypy.error[18670] 2010-02-12 13:10:23,556 INFO: ENGINE Forking twice. :cherrypy.error[18666] 2010-02-12 13:10:23,557 INFO: ENGINE Forking once. :cherrypy.error[18671] 2010-02-12 13:10:23,716 INFO: ENGINE Caught signal SIGTERM. :cherrypy.error[18671] 2010-02-12 13:10:23,716 INFO: ENGINE Bus STOPPING :cherrypy.error[18671] 2010-02-12 13:10:23,716 INFO: ENGINE HTTP Server cherrypy._cpwsgi_server.CPWSGIServer(('0.0.0.0', 12380)) already shut down :cherrypy.error[18671] 2010-02-12 13:10:23,717 INFO: ENGINE Stopped thread '_TimeoutMonitor'. :cherrypy.error[18671] 2010-02-12 13:10:23,717 INFO: ENGINE Bus STOPPED :cherrypy.error[18671] 2010-02-12 13:10:23,732 INFO: ENGINE Bus EXITING :cherrypy.error[18671] 2010-02-12 13:10:23,759 INFO: ENGINE PID file removed: '/var/mycherryd/cherry.pid'. :cherrypy.error[18671] 2010-02-12 13:10:23,782 INFO: ENGINE Bus EXITED :cherrypy.error[18671] 2010-02-12 13:10:23,792 INFO: ENGINE Serving on 0.0.0.0:12380 :cherrypy.error[18671] 2010-02-12 13:10:23,826 INFO: ENGINE Bus STARTED puppet log puppet tries to refresh the service immediately after ensuring it to be 'running'. Feb 12 13:10:22 localhost puppetd[8159]: (//mycherrypy/File[conffiles]) Scheduling refresh of Service[cherryd] Feb 12 13:10:22 localhost last message repeated 12 times Feb 12 13:10:23 localhost puppetd[8159]: (//mycherrypy/Service[mycherryd]/ensure) ensure changed 'stopped' to 'running' Feb 12 13:10:23 localhost puppetd[8159]: (//mycherrypy/Service[mycherryd]) Triggering 'refresh' from 13 dependencies Feb 12 13:11:23 localhost puppetd[8159]: (//mycherrypy/Service[mycherryd]) Failed to call refresh on Service[mycherryd]: Could not stop Service[mycherryd]: Execution of '/sbin/service mycherryd stop' returned 1: at /etc/puppet/manifests/mycherrypy.pp:161 Feb 12 13:11:24 localhost puppetd[8159]: Value of 'preferred_serialization_format' (pson) is invalid for report, using default (marshal) Feb 12 13:11:24 localhost puppetd[8159]: Finished catalog run in 99.25 seconds puppet manifest excerpt class mycherrypy { file { 'rpm': path => "/tmp/${apiserver}.i386.rpm", source => "${fileserver}/${apiserver}.i386.rpm"; 'conffiles': require => Package["${apiserver}"], path => "${service_home}/config/", ensure => present, source => "${fileserver}/config/", notify => Service["mycherryd"]; } package { "$apiserver": provider => 'rpm', source => "/tmp/${apiserver}.i386.rpm", ensure => latest; } service { "mycherryd": require => [File["conffiles"], Package["${apiserver}"]], ensure => running, provider => redhat, hasstatus => true; } }

    Read the article

  • SSD Fresh Does Not Start

    - by Jim Fell
    I recently installed a new 60GB SSD as my primary hard drive and re-installed Windows 7 Professional 64-bit. I then installed SSD Fress from Abelssoft to optimize Windows to run on the SSD. It seemed to install okay, but when I try to run the utility, its splash screen appears briefly before it quietly closes. No errors are displayed; the utility just fails to launch. I have run SSD Fresh on another SSD-equipped Windows 7 Pro x64 computer in the past without any problems. Does anyone know what might be preventing the program from running? I tried shutting down the Spybot Resident and disabling the firewall and virus scanner with no luck. I also tried running the tool as administrator; I even tried reinstalling it, running the installer as administrator. No luck. Every time I try to launch the program the Event Viewer logs this same set of errors: Error 4/2/2012 11:35:44 PM Application Error 1000 (100) Error 4/2/2012 11:35:43 PM .NET Runtime 1026 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None For those who are interested, here is my system configuration: ASRock M3A770DE AM3 AMD 770 ATX AMD Motherboard AMD Athlon II X3 455 Rana 3.3GHz Socket AM3 95W Triple-Core Desktop Processor ADX455WFGMBOX G.SKILL Value Series 8GB (2 x 4GB) 240-Pin DDR3 SDRAM DDR3 1333 (PC3 10600) Desktop Memory Model F3-10600CL9D-8GBNT Mushkin Enhanced Chronos Deluxe MKNSSDCR60GB-DX 2.5" 60GB SATA III Synchronous MLC Internal Solid State Drive (SSD) (Primary/Boot HD) Western Digital Caviar Blue RFHWD1600AAJS 160GB 7200 RPM SATA 3.0Gb/s 3.5" Internal Hard Drive -Bare Drive (Secondary HD) Sony Optiarc CD/DVD Burner Black SATA Model AD-7261S-0B LightScribe Support RAIDMAX RX-850AE 850W ATX12V v2.3 / EPS12V SLI Certified CrossFire Ready 80 PLUS GOLD Certified Modular Active PFC Power Supply ASUS HD7850-DC2-2GD5 Radeon HD 7850 2GB 256-bit GDDR5 PCI Express 3.0 x16 HDCP Ready CrossFireX Support Video Card Asus ML228H 21.5" Full HD LED BackLight LED Monitor Slim Design (x3)

    Read the article

  • Nagios NDOUtils config_type field

    - by danilo
    Can someone tell me what the config_type field in the nagios_hosts table of the Nagios NDOUtils Database means? Unfortuntely, it is not included in the database model documentation. http://nagios.sourceforge.net/docs/ndoutils/NDOUtils_DB_Model.pdf

    Read the article

  • Nagios NDOUtils config_type field

    - by danilo
    Can someone tell me what the config_type field in the nagios_hosts table of the Nagios NDOUtils Database means? Unfortuntely, it is not included in the database model documentation. http://nagios.sourceforge.net/docs/ndoutils/NDOUtils_DB_Model.pdf

    Read the article

  • App to log network user's file activities

    - by Luke
    My employer recently purchased a Mac Pro server (2011 model) and we've installed OSX Lion Server from the Mac Appstore. I'm definitely no server admin, but I have been tasked with finding out the following: Can we monitor or log what users do? (ie, open a file, copy a file.... or file-related tasks) Can we stop files from being copied? Or be alerted when this does occur? Thanks in advance for any assistance.

    Read the article

  • how to block https sites on netgear router?

    - by Karthick88it
    I am using NETGEAR Wireless-N-300 Router Model among couple of peoples to sahre internet connectivity. I have a problem, on my company i blocked facebook.com, but the users are access on protocol https, i blocked some ip´s of facebook but they haves a lot ip, please, how to block facebook on https protocol...?? Can anybody help me for creating the block HTTPS traffic rule. Like I need to block: https://www.facebook.com/ many thanks Karthick

    Read the article

  • Win7 + SysPrep + CloneZilla = lost settings

    - by oshirowanen
    I've just cloned a PC (Win7 + SysPrep + CloneZilla) and after starting up the new clone, Win7 wants to be reactivated again and the video driver seems to be missing (as in the aero effect has disappeared from the new clone) and the internet connection settings seem to be missing too. All those were set in the master before running SysPrep. Why have these settings been lost? The master PC was had windows 7 activated using a volume license key, and the clone pc is the same make and model as the master computer.

    Read the article

  • Trouble with wireless driver on a Dell Latitude D830

    - by Kevin
    After uninstalling Dell's wireless utility I get a new hardware found dialog that can not find any driver for my wifi card on it's own. I'm running Windows XP Professional Service Pack 3, and I would like to use the default wifi handler since dell's utility does not work with my company's wireless switch. I did try downloading the recommend driver from the dell support site Network Adapter 2 Model Intel(R) PRO/Wireless 3945ABG Network Connection Description [12] Intel(R) PRO/Wireless 3945ABG Network Connection Status Connected

    Read the article

  • Expert iptables help needed?

    - by Asad Moeen
    After a detailed analysis, I collected these details. I am under a UDP Flood which is more of application dependent. I run a Game-Server and an attacker is flooding me with "getstatus" query which makes the GameServer respond by making the replies to the query which cause output to the attacker's IP as high as 30mb/s and server lag. Here are the packet details, Packet starts with 4 bytes 0xff and then getstatus. Theoretically, the packet is like "\xff\xff\xff\xffgetstatus " Now that I've tried a lot of iptables variations like state and rate-limiting along side but those didn't work. Rate Limit works good but only when the Server is not started. As soon as the server starts, no iptables rule seems to block it. Anyone else got more solutions? someone asked me to contact the provider and get it done at the Network/Router but that looks very odd and I believe they might not do it since that would also affect other clients. Responding to all those answers, I'd say: Firstly, its a VPS so they can't do it for me. Secondly, I don't care if something is coming in but since its application generated so there has to be a OS level solution to block the outgoing packets. At least the outgoing ones must be stopped. Secondly, its not Ddos since just 400kb/s input generates 30mb/s output from my GameServer. That never happens in a D-dos. Asking the provider/hardware level solution should be used in that case but this one is different. And Yes, Banning his IP stops the flood of outgoing packets but he has many more IP-Addresses as he spoofs his original so I just need something to block him automatically. Even tried a lot of Firewalls but as you know they are just front-ends to iptables so if something doesn't work on iptables, what would the firewalls do? These were the rules I tried, iptables -A INPUT -p udp -m state --state NEW -m recent --set --name DDOS --rsource iptables -A INPUT -p udp -m state --state NEW -m recent --update --seconds 1 --hitcount 5 --name DDOS --rsource -j DROP It works for the attacks on un-used ports but when the server is listening and responding to the incoming queries by the attacker, it never works. Okay Tom.H, your rules were working when I modified them somehow like this: iptables -A INPUT -p udp -m length --length 1:1024 -m recent --set --name XXXX --rsource iptables -A INPUT -p udp -m string --string "xxxxxxxxxx" --algo bm --to 65535 -m recent --update --seconds 1 --hitcount 15 --name XXXX --rsource -j DROP They worked for about 3 days very good where the string "xxxxxxxxx" would be rate-limited, blocked if someone flooded and also didn't affect the clients. But just today, I tried updating the chain to try to remove a previously blocked IP so for that I had to flush the chain and restore this rule ( iptables -X and iptables -F ), some clients were already connected to servers including me. So restoring the rules now would also block some of the clients string completely while some are not affected. So does this mean I need to restart the server or why else would this happen because the last time the rules were working, there was no one connected?

    Read the article

  • Client has been through 3 PSUs, now what?

    - by Moshe
    A client of mine has an XP era eMachines. The power supply has died and been replaced 3 times. I've discharged the motherboard and checked the surge protector. In the middle of a scan with ComboFix, the machine died. It powers on and hangs before the BIOS and shows a solid yellow light. I believe the model # is T5062 or something like that.

    Read the article

  • Does the Belkin N150 support ADSL2+?

    - by peter
    Hi All, Does the Belkin N150, http://www.belkin.com/IWCatProductPage.process?Product_Id=492429 Support ADSL2+. It has a model number of F6D4630-4 v2 The website or manual doesn't seem to mention it. Or am I just looking in the wrong place? Thanks.

    Read the article

  • HW RAID 1 different disk sizes?

    - by jacka
    I was told by an HP support guy that I should not replace a failed drive in a mirror with a bigger size drive, since it could crash my array. I am puzzled why is this so and how to hell am I suppose to support this array once the specific hdd model is not available any more?

    Read the article

  • IP Micro-outages, telephone micro-outages, and CATV micro-outages

    - by Michael Graff
    This is a long and complicated question, mostly because it has been going on for 2.5 years without a solution in sight. It also is only one-third computer related, the other two-thirds are cable TV and cable-phone related. Background I have COX Communications for a cable provider, and we get Internet, digital cable TV, and digital phone service through them. The Internet is a SB5101 right now, and has been a DPC2100 and SB5120 in the past. Same results. The phone service is provided through a telephone interface mounted on the outside of the house (not classic VoIP) and the CATV is through a Scientific Atlanta receiver without DVR. I do have a TiVo connected to the CATV box. Symptoms The CATV shows "blocking" -- sometimes very very short duration where a few blocks appear on the screen. Sometimes it lasts long enough that the video "pauses" for 2-5 seconds, and rarely but not unseen the audio also fails. The CATV decoder box shows no correctable (FEC) or uncorrectable errors. That is, all BER counters are zero for the video stream. The Internet shows "micro-outages" where it appears that sent packets are not making it out, but I continue to receive packets from local modems. That is, pings stop coming back, but I continue to see modems broadcast for DHCP, and sometimes they ask more than once. The cable modem shows no errors during this time, but cable modems lie like you would not believe. It is actually possible to unplug the coax from the modem for 20 seconds and it reports NO ERRORS to the provider's tools. The phone service cuts out for 1-3 seconds, infrequently. When this happens, I hear NOTHING (not even comfort noise) and the remote side hears a "click" as if I were getting a call waiting message. However, there is no call incoming, other than the one I'm currently on of course. Things SEEM to happen more frequently when the temperature outside swings from cold to warm, so fall/spring seems worse than summer/winter. All micro-outages occur between once or twice a day (which I could ignore) to 10 times per hour. All SNR, signal levels, noise levels, etc. show very close to optimal when measured. COX's diagnosis This is a continual pain for me. Over the last 2.5 years, they have opened, "fixed" something, and closed the tickets. They close it without confirming that it is indeed better, and when I reopen they cannot do that, but instead they open a new ticket and send yet another low-level tech out to do the same signal tests and report that all is OK. I've finally gotten a line tech who has a clue and is motivated enough to pursue this with me. We have tried things like switching the local nodes over to UPS and generator power, but this does not trigger the noise. We have tried replacing all cabling, the tap outside my house, the modem, the CATV decoder -- all without resolution. Recently they have decided it is both my computer or switch, my TiVo, and my phone that are all broken and causing this issue. My debugging steps I spent the worse day of my TV-watching life yesterday and part of today. I watched live TV without the TiVo. I witnessed blocking, but it did "feel different." and was actually more severe. Some days it is better, some days it is worse, so perhaps this was just a very bad day. Today, I connected the TiVo to my DVD player, and ran two very long movies through it. I saw no blocking at all during nearly 6 hours of video. Suggestions? Does anyone have any suggestions on what to do next? I understand perhaps only the IP side can be addressed here, but it is one of the more limiting debugging options.

    Read the article

  • Vaio Laptop wireless connectivity loss after some minute

    - by Mehran Meidani
    I have a big problem with my laptop, My laptop loss it's connectivity to internet randomly! for Example sometimes it's ok up to 1h but usually the problem occurred after 5 min. When I run these command, i can continue working with internet : ipconfig /release ipconfig /renew If i turn wireless off and on, the problem don't solved I have another laptop (Macbook pro) and it doesn't have any problem I use Linksys E2000 as an wireless access point Model : Sony vaio sa21gx OS : Windows 7 SP1 Thank you for your help and sorry for my bad english :)

    Read the article

  • How to setup a Wi-Fi 2-computer network with Internet sharing?

    - by Narek
    I have the following devices: Desktop Computer (Windows XP Professional) Laptop Computer (Windows Vista Home Premium) A USB modem that I want to connect to my Desktop computer (so my Desktop has Internet) And a Wi-Fi router (D-Link, model: DIR-300) that I want to use in order to create a connection between mentioned two computers to be able to share files and what is the most important thing to make my laptop to have access to the Internet. What steps I should do to have this system?

    Read the article

  • Backup a hosted Sharepoint

    - by David Mackintosh
    One of my customers has outsourced their Sharepoint and Exchange services to a hosted services provider. I believe it is a Sharepoint 2007 service. It is a shared hosting solution, so we do not have any kind of access to the server itself; we only have user-level and sharepoint-administrator-level access to the Sharepoint application. They have come to the point where they would like to have a copy of everything that is on the Sharepoint server. I have downloaded the Office Sharepoint Designer 2007, and it features three (!) ways to backup a Sharepoint server, none (!) of which work for me: File-Export-Personal Web Package: When selecting everything, it calculates a negative size. Barfs with No "content-type" in CGI environment error. File-Export-Sharepoint Template: barfs with a A World Wide Web browser, such as Windows Internet Explorer, is required to use this feature error. Site-Administration-Backup Web Site: wants to create the backup .cmp file on the sharepoint server itself. I don't have access to any servers on the same network so I can't redirect it to any form of the suggested \\server\place. Barfs with a The Web application at $URL could not be found. [...] error. Possibly moot because Google tells me that bad things happen using OSD to back up sites larger than 24MB (which this site is most definitely). So I called the helpdesk of the outsource provider, and got told that they recommend using OSD, but no they don't actually provide any application support for OSD (not that I blame them for that), but they could do a stsadm.exe backup and provide us with that, and OSD should be able to read the resulting cmp file. Then for authorization reasons they had my customer call them directly (since I can't authorize such an operation), and they told him that he didn't want a stsadm.exe backup, he wanted to get into an 'explorer view' and deal with things that way (they were vague). Google hasn't been much help in figuring out what an 'explorer view' is, let alone how I bring one up. The end goal of this operation is to have a backup of the site as it exists (hopefully today, but shortly anyways) in such a format that we don't need another sharepoint server to restore it to. Ie we'd like to be able to pick individual content directly out of this backup. We are not excessively concerned with things like formatting. We just want the documents. This is a fairly complex site with multiple subsites and multiple folders per subsite, so sitting there and manually downloading each file isn't really going to happen if there is a better easier way. So, my questions: Is the stsadm.exe backup what I want? If not, what do I want? If I manage to convince them that I do want the stsadm.exe backup, can I pick files out of the resulting backup file with OSD? If OSD isn't going to let me extract individual files, is there a tool I can use that can?

    Read the article

  • Licensing for SQL Server Merge Replication via Web Syncronization

    - by user43330
    I am planning to implement a Sales force automation software where there will be 50 PDA devices having sql server CE 3.5 connecting via web sync merge replication to central SQL Server 2005 main Database via a IIS server. 1) IIS Server Win 2003 Server 2) SQL Server 2005 Standard 3) SQL CE 3.5 having in 50 PDA Devices. How many licenses are required for each Servers ? What is the licencing model

    Read the article

  • Cannot create zpool, how to get rid of intel raid volume?

    - by nagylzs
    This is a FreeBSD 9.1 amd64 computer. It has 5 disks installed. The ada0 and ada1 disks are used with a hw raid to provide the root filesystem: root@gw:/home/gandalf # ls /dev | grep ada ada0 ada1 ada2 ada3 ada4 root@gw:/home/gandalf # zpool status pool: zroot state: ONLINE scan: none requested config: NAME STATE READ WRITE CKSUM zroot ONLINE 0 0 0 raid/r0s1a ONLINE 0 0 0 errors: No known data errors I want to create a raidz pool for the remaining disks: root@gw:/home/gandalf # zpool create -f data raidz1 ada2 ada3 ada4 cannot create 'data': one or more devices is currently unavailable root@gw:/home/gandalf # dmesg | grep ada2 ada2 at ata4 bus 0 scbus6 target 0 lun 0 ada2: <WDC WD20EARS-00MVWB0 51.0AB51> ATA-8 SATA 2.x device ada2: 300.000MB/s transfers (SATA 2.x, UDMA5, PIO 8192bytes) ada2: 1907729MB (3907029168 512 byte sectors: 16H 63S/T 16383C) ada2: Previously was known as ad16 root@gw:/home/gandalf # dmesg | grep ada3 ada3 at ata5 bus 0 scbus7 target 0 lun 0 ada3: <SAMSUNG HD103UJ 1AA01118> ATA-7 SATA 2.x device ada3: 300.000MB/s transfers (SATA 2.x, UDMA5, PIO 8192bytes) ada3: 953868MB (1953523055 512 byte sectors: 16H 63S/T 16383C) ada3: Previously was known as ad18 GEOM_RAID: Intel-fb8732fa: Disk ada3 state changed from NONE to ACTIVE. GEOM_RAID: Intel-fb8732fa: Subdisk Volume0:0-ada3 state changed from NONE to ACTIVE. root@gw:/home/gandalf # dmesg | grep ada4 ada4 at ata6 bus 0 scbus8 target 0 lun 0 ada4: <TOSHIBA DT01ACA100 MS2OA750> ATA-8 SATA 3.x device ada4: 300.000MB/s transfers (SATA 2.x, UDMA5, PIO 8192bytes) ada4: 953869MB (1953525168 512 byte sectors: 16H 63S/T 16383C) ada4: Previously was known as ad20 root@gw:/home/gandalf # dmesg | grep GEOM_RAID Aha, so ada3 is already part of another raid volume? Let's see: root@gw:/home/gandalf # dmesg | grep GEOM_RAID GEOM_RAID: SiI-130628113902: Array SiI-130628113902 created. GEOM_RAID: SiI-130628113902: Disk ada0 state changed from NONE to ACTIVE. GEOM_RAID: SiI-130628113902: Subdisk SiI Raid1 Set:1-ada0 state changed from NONE to STALE. GEOM_RAID: SiI-130628113902: Disk ada1 state changed from NONE to ACTIVE. GEOM_RAID: SiI-130628113902: Subdisk SiI Raid1 Set:0-ada1 state changed from NONE to STALE. GEOM_RAID: SiI-130628113902: Array started. GEOM_RAID: SiI-130628113902: Subdisk SiI Raid1 Set:0-ada1 state changed from STALE to ACTIVE. GEOM_RAID: SiI-130628113902: Subdisk SiI Raid1 Set:1-ada0 state changed from STALE to RESYNC. GEOM_RAID: SiI-130628113902: Subdisk SiI Raid1 Set:1-ada0 rebuild start at 0. GEOM_RAID: SiI-130628113902: Volume SiI Raid1 Set state changed from STARTING to SUBOPTIMAL. GEOM_RAID: SiI-130628113902: Provider raid/r0 for volume SiI Raid1 Set created. GEOM_RAID: Intel-fb8732fa: Array Intel-fb8732fa created. GEOM_RAID: Intel-fb8732fa: Force array start due to timeout. GEOM_RAID: Intel-fb8732fa: Disk ada3 state changed from NONE to ACTIVE. GEOM_RAID: Intel-fb8732fa: Subdisk Volume0:0-ada3 state changed from NONE to ACTIVE. GEOM_RAID: Intel-fb8732fa: Array started. GEOM_RAID: Intel-fb8732fa: Volume Volume0 state changed from STARTING to DEGRADED. GEOM_RAID: Intel-fb8732fa: Provider raid/r1 for volume Volume0 created. root@gw:/home/gandalf # Yes, indeed. I want to get rid of raid/r1 completely. However, the controller was already set to "IDE" mode in the BIOS. So why it is creating a raid volume??? I have also tried overwritting the first 16k data of ada3 and reboot the computer, but it did not help. How can I delete /dev/raid/r1 ? root@gw:/home/gandalf # graid status Name Status Components raid/r0 SUBOPTIMAL ada0 (ACTIVE (RESYNC 4%)) ada1 (ACTIVE (ACTIVE)) raid/r1 DEGRADED ada3 (ACTIVE (ACTIVE)) root@gw:/home/gandalf # graid delete raid/r1 graid: Array 'raid/r1' not found. root@gw:/home/gandalf # graid delete /dev/raid/r1 graid: Array '/dev/raid/r1' not found. root@gw:/home/gandalf # Thanks

    Read the article

  • What do the numbers on Western Digital drives mean?

    - by Evan Carroll
    There are numerous numbers on a Western Digital drive, MDL (presumably model, ex WD5000BEKT-00KA9T0) -- not sure what the 99KA9T0 is. WWN (ex 50014EE25AC8C945) DCM (ex HBNTJBBB) LBA (ex 976773168) R/N (ex 77174) Then there are three numbers on the back of the PCB on a sticker White Sticker Left: 2061-771714-002 AC White Sticker Right: XT BD34 T7KQ 8 0002270 White Sticker far-Right: 272 Then there is one number printed on the PCB, REV P1 2060-771714-002 Then there is one number (or three) on the spindle, 71206-T8Y-03 9X0X22MF 32H Does anyone know what these numbers mean?

    Read the article

  • activate wireless chip on ubuntu

    - by Charles
    I am currently using ubuntu 10.10 on my laptop , the model of my wireless chip is broadcom BCM4312 802.11b/g LP-PHY . I tried to activate the driver for the chip by clicking menu bar System - Administration - Additional Drivers . and activated Broadcom STA wireless driver. But the laptop can't detect any wireless signal still. Do I have to do any additional work to make the chip work ? Or how can I test if there is physical damage to the chip itself

    Read the article

< Previous Page | 329 330 331 332 333 334 335 336 337 338 339 340  | Next Page >