Search Results

Search found 9750 results on 390 pages for 'sys debug'.

Page 345/390 | < Previous Page | 341 342 343 344 345 346 347 348 349 350 351 352  | Next Page >

• Debugging IO limitation

  - by Martin F

  I have a Fedora box with some severe IO limitations which I have no idea how to debug. The server has a Areca Technology Corp. ARC-1130 12-Port PCI-X to SATA RAID Controller with 12 7200 RPM 1.5 TB disks and a Marvell Technology Group Ltd. 88E8050 PCI-E ASF Gigabit Ethernet Controller. uname -a output: 2.6.32.11-99.fc12.x86_64 #1 SMP Mon Apr 5 19:59:38 UTC 2010 x86_64 x86_64 x86_64 GNU/Linux The server is a file server running Nginx with the stub status module enabled, so I can see the current amount of connections. The problem present itself when I have a high number of simultaneous connections in a writing state. Usually around 350, at this very moment it's at 590 and the server is almost unusable and stuck at 230mbit/s. If I run stop and hit 1 to see CPU core usages I have all 4 cores with around 99% io wait, if I run iotop the nginx workers are the only processes producing any read load, currently at around 25MB/s. I have each of the workers bound to their own core. Initially I figured it was just the disks being bugged. But I've run fscheck and smartmontools checks and found no errors. I also ran an iozone test which you can see the result of here: http://www.pastie.org/951667.txt?key=fimcvljulnuqy2dcdxa Additionally, when the amount of connections are low I have no problem getting a good speed. If I wget over the local network it easily hits 60MB/sec. Right now I just tried putting a file in /dev/shm, then I symlinked a file from the public dir to it and used wget over the local network and only got 50KB/s. Also, if I try to cp /dev/shm/test /root/test it quickly copies around 740MB and then slows down HEAVILY. Again with iotop reporting 99% iowait. I'm not really sure how to go about figuring out what the problems are. It could be a natural disk limitation but then the file from /dev/shm ought to transfer so it seems there's a network limit, but that's fine when there's not many connections. Perhaps it's a TCP stack problem but I really have no idea how to check that. Any suggestions on how to proceed with debugging would be very welcome. If additional information is required then let me know and I'll try to get it. Thanks.

  Read the article

• Unable to access intel fake RAID 1 array in Fedora 14 after reboot

  - by Sim

  Hello everyone, 1st I am relatively new to linux (but not to *nix). I have 4 disks assembled in the following intel ahci bios fake raid arrays: 2x320GB RAID1 - used for operating systems md126 2x1TB RAID1 - used for data md125 I have used the raid of size 320GB to install my operating system and the second raid I didn't even select during the installation of Fedora 14. After successful partitioning and installation of Fedora, I tried to make the second array available, it was possible to make it visible in linux with mdadm --assembe --scan , after that I created one maximum size partition and 1 maximum size ext4 filesystem in it. Mounted, and used it. After restart - a few I/O errors during boot regarding md125 + inability to mount the filesystem on it and dropped into repair shell. I commented the filesystem in fstab and it booted. To my surprise, the array was marked as "auto read only": [root@localhost ~]# cat /proc/mdstat Personalities : [raid1] md125 : active (auto-read-only) raid1 sdc[1] sdd[0] 976759808 blocks super external:/md127/0 [2/2] [UU] md127 : inactive sdc[1](S) sdd[0](S) 4514 blocks super external:imsm md126 : active raid1 sda[1] sdb[0] 312566784 blocks super external:/md1/0 [2/2] [UU] md1 : inactive sdb[1](S) sda[0](S) 4514 blocks super external:imsm unused devices: <none> [root@localhost ~]# and the partition in it was not available as device special file in /dev: [root@localhost ~]# ls -l /dev/md125* brw-rw---- 1 root disk 9, 125 Jan 6 15:50 /dev/md125 [root@localhost ~]# But the partition is there according to fdisk: [root@localhost ~]# fdisk -l /dev/md125 Disk /dev/md125: 1000.2 GB, 1000202043392 bytes 19 heads, 10 sectors/track, 10281682 cylinders, total 1953519616 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x1b238ea9 Device Boot Start End Blocks Id System /dev/md125p1 2048 1953519615 976758784 83 Linux [root@localhost ~]# I tried to "activate" the array in different ways (I'm not experienced with mdadm and the man page is gigantic so I was only browsing it looking for my answer) but it was impossible - the array would still stay in "auto read only" and the device special file for the partition it will not be in /dev. It was only after I recreated the partition via fdisk that it reappeared in /dev... until next reboot. So, my question is - How do I make the array automatically available after reboot? Here is some additional information: 1st I am able to see the UUID of the array in blkid: [root@localhost ~]# blkid /dev/sdc: UUID="b9a1149f-ae11-4fc8-a600-0d77354dc42a" SEC_TYPE="ext2" TYPE="ext3" /dev/sdd: UUID="b9a1149f-ae11-4fc8-a600-0d77354dc42a" SEC_TYPE="ext2" TYPE="ext3" /dev/md126p1: UUID="60C8D9A7C8D97C2A" TYPE="ntfs" /dev/md126p2: UUID="3d1b38a3-b469-4b7c-b016-8abfb26a5d7d" TYPE="ext4" /dev/md126p3: UUID="1Msqqr-AAF8-k0wi-VYnq-uWJU-y0OD-uIFBHL" TYPE="LVM2_member" /dev/mapper/vg00-rootlv: LABEL="_Fedora-14-x86_6" UUID="34cc1cf5-6845-4489-8303-7a90c7663f0a" TYPE="ext4" /dev/mapper/vg00-swaplv: UUID="4644d857-e13b-456c-ac03-6f26299c1046" TYPE="swap" /dev/mapper/vg00-homelv: UUID="82bd58b2-edab-4b4b-aec4-b79595ecd0e3" TYPE="ext4" /dev/mapper/vg00-varlv: UUID="1b001444-5fdd-41b6-a59a-9712ec6def33" TYPE="ext4" /dev/mapper/vg00-tmplv: UUID="bf7d2459-2b35-4a1c-9b81-d4c4f24a9842" TYPE="ext4" /dev/md125: UUID="b9a1149f-ae11-4fc8-a600-0d77354dc42a" SEC_TYPE="ext2" TYPE="ext3" /dev/sda: TYPE="isw_raid_member" /dev/md125p1: UUID="420adfdd-6c4e-4552-93f0-2608938a4059" TYPE="ext4" [root@localhost ~]# Here is how /etc/mdadm.conf looks like: [root@localhost ~]# cat /etc/mdadm.conf # mdadm.conf written out by anaconda MAILADDR root AUTO +imsm +1.x -all ARRAY /dev/md1 UUID=89f60dee:e46a251f:7475814b:d4cc19a9 ARRAY /dev/md126 UUID=a8775c90:cee66376:5310fc13:63bcba5b ARRAY /dev/md125 UUID=b9a1149f:ae114fc8:a6000d77:354dc42a [root@localhost ~]# here is how /proc/mdstat looks like after I recreate the partition in the array so that it becomes available: [root@localhost ~]# cat /proc/mdstat Personalities : [raid1] md125 : active raid1 sdc[1] sdd[0] 976759808 blocks super external:/md127/0 [2/2] [UU] md127 : inactive sdc[1](S) sdd[0](S) 4514 blocks super external:imsm md126 : active raid1 sda[1] sdb[0] 312566784 blocks super external:/md1/0 [2/2] [UU] md1 : inactive sdb[1](S) sda[0](S) 4514 blocks super external:imsm unused devices: <none> [root@localhost ~]# Detailed output regarding the array in subject: [root@localhost ~]# mdadm --detail /dev/md125 /dev/md125: Container : /dev/md127, member 0 Raid Level : raid1 Array Size : 976759808 (931.51 GiB 1000.20 GB) Used Dev Size : 976759940 (931.51 GiB 1000.20 GB) Raid Devices : 2 Total Devices : 2 Update Time : Fri Jan 7 00:38:00 2011 State : clean Active Devices : 2 Working Devices : 2 Failed Devices : 0 Spare Devices : 0 UUID : 30ebc3c2:b6a64751:4758d05c:fa8ff782 Number Major Minor RaidDevice State 1 8 32 0 active sync /dev/sdc 0 8 48 1 active sync /dev/sdd [root@localhost ~]# and /etc/fstab, with /data commented (the filesystem that is on this array): # # /etc/fstab # Created by anaconda on Thu Jan 6 03:32:40 2011 # # Accessible filesystems, by reference, are maintained under '/dev/disk' # See man pages fstab(5), findfs(8), mount(8) and/or blkid(8) for more info # /dev/mapper/vg00-rootlv / ext4 defaults 1 1 UUID=3d1b38a3-b469-4b7c-b016-8abfb26a5d7d /boot ext4 defaults 1 2 #UUID=420adfdd-6c4e-4552-93f0-2608938a4059 /data ext4 defaults 0 1 /dev/mapper/vg00-homelv /home ext4 defaults 1 2 /dev/mapper/vg00-tmplv /tmp ext4 defaults 1 2 /dev/mapper/vg00-varlv /var ext4 defaults 1 2 /dev/mapper/vg00-swaplv swap swap defaults 0 0 tmpfs /dev/shm tmpfs defaults 0 0 devpts /dev/pts devpts gid=5,mode=620 0 0 sysfs /sys sysfs defaults 0 0 proc /proc proc defaults 0 0 [root@localhost ~]# Thanks in advance to everyone that even read this whole issue :-)

  Read the article

• Ubuntu box static routing problem

  - by Rafael

  Hello, I'm trying to configure a ubuntu server to be a router. This is my interface configuration (eth2 connects to my WAN, eth0 to my LAN): auto eth2 iface eth2 inet static address 192.168.0.249 netmask 255.255.255.0 gateway 192.168.0.1 broadcast 192.168.0.255 auto eth0 iface eth0 inet static address 192.168.100.1 netmask 255.255.255.0 This is the router information: Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.100.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 192.168.0.0 0.0.0.0 255.255.255.0 U 0 0 0 eth2 0.0.0.0 192.168.0.1 0.0.0.0 UG 100 0 0 eth2 And this is dhcp configuration: subnet 192.168.100.0 netmask 255.255.255.0 { range 192.168.100.101 192.168.100.254; option domain-name-servers 201.70.86.133; option routers 192.168.100.1; authoritative; } I'm then connecting a mac os x by cable on eth0. This is en0 interface configuration: en0: flags=8963<UP,BROADCAST,SMART,RUNNING,PROMISC,SIMPLEX,MULTICAST> mtu 1500 ether 00:26:bb:5d:82:b0 inet6 fe80::226:bbff:fe5d:82b0%en0 prefixlen 64 scopeid 0x4 inet 192.168.100.101 netmask 0xffffff00 broadcast 192.168.100.255 media: autoselect (100baseTX <full-duplex>) status: active And this is the routing table: Internet: Destination Gateway Flags Refs Use Netif Expire default 192.168.100.1 UGSc 139 32 en0 10.37.129/24 link#8 UC 2 0 vnic1 10.37.129.2 0:1c:42:0:0:9 UHLWI 0 839 lo0 10.37.129.255 ff:ff:ff:ff:ff:ff UHLWbI 0 4 vnic1 10.211.55/24 link#7 UC 2 0 vnic0 10.211.55.2 0:1c:42:0:0:8 UHLWI 0 840 lo0 10.211.55.255 ff:ff:ff:ff:ff:ff UHLWbI 0 4 vnic0 127 127.0.0.1 UCS 0 0 lo0 127.0.0.1 127.0.0.1 UH 3 507924 lo0 169.254 link#4 UCS 0 0 en0 172.16.42/24 link#10 UC 2 0 vmnet8 172.16.42.1 0:50:56:c0:0:8 UHLWI 0 839 lo0 172.16.42.255 link#10 UHLWbI 1 24 vmnet8 192.168.100 link#4 UC 2 0 en0 192.168.100.1 0:e0:7c:7e:f:99 UHLWI 139 0 en0 777 192.168.100.101 127.0.0.1 UHS 0 0 lo0 192.168.100.255 ff:ff:ff:ff:ff:ff UHLWbI 0 4 en0 192.168.116 link#9 UC 2 0 vmnet1 192.168.116.1 0:50:56:c0:0:1 UHLWI 0 839 lo0 192.168.116.255 ff:ff:ff:ff:ff:ff UHLWbI 0 4 vmnet1 When I ping 192.168.100.1, it works. When I ping 192.168.0.249, it also works. However, when I try to ping 192.168.0.1 it does not. Does anyone has any way to solve this? Is there a way to debug it? Thanks,

  Read the article

• What PHP, Xdebug and Eclipse configurations work on Windows 7 64 bit?

  - by thaddeusmt

  I have been mucking around for days, trying to find the right combination that lets me debug with breakpoints and variable viewing, in Eclipse, without crashing Apache. PHP 5.3? PHP 5.2? Eclipse Helios? Eclipse Galileo? One or the other with certain versions of xdebug or php? Or do I really need to use NetBeans or something else? Is my 64 bit OS the problem? Do need specific 64bit versions of PHP, Eclipse or Xdebug to work on Windows 7 64? Any special xdebug config options and tricks that I need in php.ini? Like turning off xdebug.profiler_enable or not using quotes around my zend_extension path to the xdebug dll? A Vhosts issue? Scrap the whole thing and go back to Win XP or Ubuntu? Here's what I've already been reading: http://stackoverflow.com/questions/4509245/so-eclipse-and-xdebug-walk-into-a-bar-and-then-my-apache-server-dies/4602473 http://stackoverflow.com/questions/206788/why-does-xdebug-crash-apache-on-every-xampp-install-ive-tried http://bugs.xdebug.org/view.php?id=459 https://bugs.eclipse.org/bugs/show_bug.cgi?id=312951#c8 http://stackoverflow.com/questions/2799936/xdebug-for-php-5-2-on-windows-7-64bit and so and so on... SO, xdebug bug tracker, eclipse bugzilla, etc, etc Basically what would be great is if folks could post their working (i.e. debugging with breakpoints and local variable viewing in Eclipse) Win7 64bit configurations, including: PHP version (5.3.1, 5.2.11, etc) Xdebug dll (2.1.0-5.3-vc6, etc) Xdebug php.ini config (zend_extension = "C:\xampp\php\ext\php_xdebug.dll", etc) Apache version (2.2.14, etc) Eclipse version Anything else important? The "secret ingredient"? Thanks! I miss my debugger since I got a new laptop with Win 7! Sadly it looks like some of the drivers (switchable graphics, multi-touch pad, etc) on my lappy don't work right with Ubuntu yet, so I feel a bit trapped on Win :( I know I will figure something out eventually, but I've been at this trial-and-error game a while and am seeking some guidance. (Originally posted on StackOverflow here, but moved to SuperUser:) http://stackoverflow.com/questions/4628215/what-php-xdebug-and-eclipse-configurations-work-on-windows-7-64-bit

  Read the article

• HAProxy + Percona XtraDB Cluster

  - by rottmanj

  I am attempting to setup HAproxy in conjunction with Percona XtraDB Cluster on a series of 3 EC2 instances. I have found a few tutorials online dealing with this specific issue, but I am a bit stuck. Both the Percona servers and the HAproxy servers are running ubuntu 12.04. The HAProxy version is 1.4.18, When I start HAProxy I get the following error: Server pxc-back/db01 is DOWN, reason: Socket error, check duration: 2ms. I am not really sure what the issue could be. I have verified the following: EC2 security groups ports are open Poured over my config files looking for issues. I currently do not see any. Ensured that xinetd was installed Ensured that I am using the correct ip address of the mysql server. Any help with this is greatly appreciated. Here are my current config Load Balancer /etc/haproxy/haproxy.cfg global log 127.0.0.1 local0 log 127.0.0.1 local1 notice maxconn 4096 user haproxy group haproxy debug #quiet daemon defaults log global mode http option tcplog option dontlognull retries 3 option redispatch maxconn 2000 contimeout 5000 clitimeout 50000 srvtimeout 50000 frontend pxc-front bind 0.0.0.0:3307 mode tcp default_backend pxc-back frontend stats-front bind 0.0.0.0:22002 mode http default_backend stats-back backend pxc-back mode tcp balance leastconn option httpchk server db01 10.86.154.105:3306 check port 9200 inter 12000 rise 3 fall 3 backend stats-back mode http balance roundrobin stats uri /haproxy/stats MySql Server /etc/xinetd.d/mysqlchk # default: on # description: mysqlchk service mysqlchk { # this is a config for xinetd, place it in /etc/xinetd.d/ disable = no flags = REUSE socket_type = stream port = 9200 wait = no user = nobody server = /usr/bin/clustercheck log_on_failure += USERID #only_from = 0.0.0.0/0 # recommended to put the IPs that need # to connect exclusively (security purposes) per_source = UNLIMITED } MySql Server /etc/services Added the line mysqlchk 9200/tcp # mysqlchk MySql Server /usr/bin/clustercheck # GNU nano 2.2.6 File: /usr/bin/clustercheck #!/bin/bash # # Script to make a proxy (ie HAProxy) capable of monitoring Percona XtraDB Cluster nodes properly # # Author: Olaf van Zandwijk <[email protected]> # Documentation and download: https://github.com/olafz/percona-clustercheck # # Based on the original script from Unai Rodriguez # MYSQL_USERNAME="testuser" MYSQL_PASSWORD="" ERR_FILE="/dev/null" AVAILABLE_WHEN_DONOR=0 # # Perform the query to check the wsrep_local_state # WSREP_STATUS=`mysql --user=${MYSQL_USERNAME} --password=${MYSQL_PASSWORD} -e "SHOW STATUS LIKE 'wsrep_local_state';" 2>${ERR_FILE} | awk '{if (NR!=1){print $2}}' 2>${ERR_FILE}` if [[ "${WSREP_STATUS}" == "4" ]] || [[ "${WSREP_STATUS}" == "2" && ${AVAILABLE_WHEN_DONOR} == 1 ]] then # Percona XtraDB Cluster node local state is 'Synced' => return HTTP 200 /bin/echo -en "HTTP/1.1 200 OK\r\n" /bin/echo -en "Content-Type: text/plain\r\n" /bin/echo -en "\r\n" /bin/echo -en "Percona XtraDB Cluster Node is synced.\r\n" /bin/echo -en "\r\n" else # Percona XtraDB Cluster node local state is not 'Synced' => return HTTP 503 /bin/echo -en "HTTP/1.1 503 Service Unavailable\r\n" /bin/echo -en "Content-Type: text/plain\r\n" /bin/echo -en "\r\n" /bin/echo -en "Percona XtraDB Cluster Node is not synced.\r\n" /bin/echo -en "\r\n" fi

  Read the article

• chrooting user causes "connection closed" message when using sftp

  - by George Reith

  First off I am a linux newbie so please don't assume much knowledge. I am using CentOS 5.8 (final) and using OpenSSH version 5.8p1. I have made a user playwithbits and I am attempting to chroot them to the directory home/nginx/domains/playwithbits/public I am using the following match statement in my sshd_config file: Match group web-root-locked ChrootDirectory /home/nginx/domains/%u/public X11Forwarding no AllowTcpForwarding no ForceCommand /usr/libexec/openssh/sftp-server # id playwithbits returns: uid=504(playwithbits) gid=504(playwithbits) groups=504(playwithbits),507(web-root-locked) I have changed the user's home directory to: home/nginx/domains/playwithbits/public Now when I attempt to sftp in with this user I instantly get the message: connection closed Does anyone know what I am doing wrong? Edit: Following advice from @Dennis Williamson I have connected in debug mode (I think... correct me if I'm wrong). I have made a bit of progress by using chmod to set permissions recursively of all files in the directly to 700. Now I get the following messages when I attempt to log on (still connection refused): Connection from [My ip address] port 38737 debug1: Client protocol version 2.0; client software version OpenSSH_5.6 debug1: match: OpenSSH_5.6 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.8 debug1: permanently_set_uid: 74/74 debug1: list_hostkey_types: ssh-rsa,ssh-dss debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: client->server aes128-ctr hmac-md5 none debug1: kex: server->client aes128-ctr hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST received debug1: SSH2_MSG_KEX_DH_GEX_GROUP sent debug1: expecting SSH2_MSG_KEX_DH_GEX_INIT debug1: SSH2_MSG_KEX_DH_GEX_REPLY sent debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: KEX done debug1: userauth-request for user playwithbits service ssh-connection method none debug1: attempt 0 failures 0 debug1: user playwithbits matched group list web-root-locked at line 91 debug1: PAM: initializing for "playwithbits" debug1: PAM: setting PAM_RHOST to [My host info] debug1: PAM: setting PAM_TTY to "ssh" debug1: userauth-request for user playwithbits service ssh-connection method password debug1: attempt 1 failures 0 debug1: PAM: password authentication accepted for playwithbits debug1: do_pam_account: called Accepted password for playwithbits from [My ip address] port 38737 ssh2 debug1: monitor_child_preauth: playwithbits has been authenticated by privileged process debug1: SELinux support disabled debug1: PAM: establishing credentials User child is on pid 3942 debug1: PAM: establishing credentials Changed root directory to "/home/nginx/domains/playwithbits/public" debug1: permanently_set_uid: 504/504 debug1: Entering interactive session for SSH2. debug1: server_init_dispatch_20 debug1: server_input_channel_open: ctype session rchan 0 win 2097152 max 32768 debug1: input_session_request debug1: channel 0: new [server-session] debug1: session_new: session 0 debug1: session_open: channel 0 debug1: session_open: session 0: link with channel 0 debug1: server_input_channel_open: confirm session debug1: server_input_global_request: rtype [email protected] want_reply 0 debug1: server_input_channel_req: channel 0 request env reply 0 debug1: session_by_channel: session 0 channel 0 debug1: session_input_channel_req: session 0 req env debug1: server_input_channel_req: channel 0 request subsystem reply 1 debug1: session_by_channel: session 0 channel 0 debug1: session_input_channel_req: session 0 req subsystem subsystem request for sftp by user playwithbits debug1: subsystem: cannot stat /usr/libexec/openssh/sftp-server: Permission denied debug1: subsystem: exec() /usr/libexec/openssh/sftp-server debug1: Forced command (config) '/usr/libexec/openssh/sftp-server' debug1: session_new: session 0 debug1: Received SIGCHLD. debug1: session_by_pid: pid 3943 debug1: session_exit_message: session 0 channel 0 pid 3943 debug1: session_exit_message: release channel 0 debug1: session_by_channel: session 0 channel 0 debug1: session_close_by_channel: channel 0 child 0 debug1: session_close: session 0 pid 0 debug1: channel 0: free: server-session, nchannels 1 Received disconnect from [My ip address]: 11: disconnected by user debug1: do_cleanup debug1: do_cleanup debug1: PAM: cleanup debug1: PAM: closing session debug1: PAM: deleting credentials

  Read the article

• lighttpd: weird behavior on multiple rewrite rule matches

  - by netmikey

  I have a 20-rewrite.conf for my php application looking like this: $HTTP["host"] =~ "www.mydomain.com" { url.rewrite-once += ( "^/(img|css)/.*" => "$0", ".*" => "/my_app.php" ) } I want to be able to put the webserver in kind of a "maintenance" mode while I update my application from scm. To do this, my idea was to enable an additional rewrite configuration file before this one. The 16-rewrite-maintenance.conf file looks like this: url.rewrite-once += ( "^/(img|css)/.*" => "$0", ".*" => "/maintenance_app.php" ) Now, on the maintenance page, I have a logo that doesn't get loaded. I get a 404 error. Lighttpd debug says the following: 2012-12-13 20:28:06: (response.c.300) -- splitting Request-URI 2012-12-13 20:28:06: (response.c.301) Request-URI : /img/content/logo.png 2012-12-13 20:28:06: (response.c.302) URI-scheme : http 2012-12-13 20:28:06: (response.c.303) URI-authority: localhost 2012-12-13 20:28:06: (response.c.304) URI-path : /img/content/logo.png 2012-12-13 20:28:06: (response.c.305) URI-query : 2012-12-13 20:28:06: (response.c.300) -- splitting Request-URI 2012-12-13 20:28:06: (response.c.301) Request-URI : /img/content/logo.png, /img/content/logo.png 2012-12-13 20:28:06: (response.c.302) URI-scheme : http 2012-12-13 20:28:06: (response.c.303) URI-authority: localhost 2012-12-13 20:28:06: (response.c.304) URI-path : /img/content/logo.png, /img/content/logo.png 2012-12-13 20:28:06: (response.c.305) URI-query : 2012-12-13 20:28:06: (response.c.349) -- sanatising URI 2012-12-13 20:28:06: (response.c.350) URI-path : /img/content/logo.png, /img/content/logo.png 2012-12-13 20:28:06: (mod_access.c.135) -- mod_access_uri_handler called 2012-12-13 20:28:06: (response.c.470) -- before doc_root 2012-12-13 20:28:06: (response.c.471) Doc-Root : /www 2012-12-13 20:28:06: (response.c.472) Rel-Path : /img/content/logo.png, /img/content/logo.png 2012-12-13 20:28:06: (response.c.473) Path : 2012-12-13 20:28:06: (response.c.521) -- after doc_root 2012-12-13 20:28:06: (response.c.522) Doc-Root : /www 2012-12-13 20:28:06: (response.c.523) Rel-Path : /img/content/logo.png, /img/content/logo.png 2012-12-13 20:28:06: (response.c.524) Path : /www/img/content/logo.png, /img/content/logo.png 2012-12-13 20:28:06: (response.c.541) -- logical -> physical 2012-12-13 20:28:06: (response.c.542) Doc-Root : /www 2012-12-13 20:28:06: (response.c.543) Rel-Path : /img/content/logo.png, /img/content/logo.png 2012-12-13 20:28:06: (response.c.544) Path : /www/img/content/logo.png, /img/content/logo.png 2012-12-13 20:28:06: (response.c.561) -- handling physical path 2012-12-13 20:28:06: (response.c.562) Path : /www/img/content/logo.png, /img/content/logo.png 2012-12-13 20:28:06: (response.c.618) -- file not found 2012-12-13 20:28:06: (response.c.619) Path : /www/img/content/logo.png, /img/content/logo.png Any clue on why lighttpd matches both rules (from my application rewrite config and from my maintenance rewrite config) and concatenates them with a comma - that doesn't seem to make any sense?! Shouldn't it stop after the first match with rewrite-once?

  Read the article

• Passwordless ssh failed when login using username

  - by Aczire

  I was trying to setup Hadoop and was stumbled on passwordless ssh to localhost. I am getting a password prompt when trying to connect using ssh username@hostname format. But there is no problem connecting to the machine like ssh localhost or ssh hostname.com. Tried ssh-copy-id user@hostname but it did not work. Using CentOS 6.3 as normal user, I neither have root access or am a sudoer so editing any files like sshd_config is not possible (not even cat the sshd_config file contents). I hope the user login is possible since I can do login without password to localhost, right? Please advise, Here is the ssh debug output. [[email protected] ~]$ ssh -v [email protected] OpenSSH_5.3p1, OpenSSL 1.0.0-fips 29 Mar 2010 debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for * debug1: Connecting to hostname.com [::1] port 22. debug1: Connection established. debug1: identity file /home/user/.ssh/identity type -1 debug1: identity file /home/user/.ssh/id_rsa type -1 debug1: identity file /home/user/.ssh/id_dsa type 2 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.3 debug1: match: OpenSSH_5.3 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.3 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-ctr hmac-md5 none debug1: kex: client->server aes128-ctr hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Host 'hostname.com' is known and matches the RSA host key. debug1: Found key in /home/user/.ssh/known_hosts:1 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey,gssapi-keyex,gssapi-with-mic,password debug1: Next authentication method: gssapi-keyex debug1: No valid Key exchange context debug1: Next authentication method: gssapi-with-mic debug1: Unspecified GSS failure. Minor code may provide more information Credentials cache file '/tmp/krb5cc_500' not found debug1: Unspecified GSS failure. Minor code may provide more information Credentials cache file '/tmp/krb5cc_500' not found debug1: Unspecified GSS failure. Minor code may provide more information debug1: Unspecified GSS failure. Minor code may provide more information debug1: Next authentication method: publickey debug1: Offering public key: /home/user/.ssh/id_dsa debug1: Server accepts key: pkalg ssh-dss blen 434 Agent admitted failure to sign using the key. debug1: Trying private key: /home/user/.ssh/identity debug1: Trying private key: /home/user/.ssh/id_rsa debug1: Next authentication method: password [email protected]'s password:

  Read the article

• nginx probably deliering wrong filetype for .css file with php tags

  - by Katai

  And again - NGINX is giving me many Questions today :) Like always, I already tried around for a while, but cant seem to fix this issue: I just configured NGINX to handle my .css files equal to my .php files (to parse PHP tags inside the CSS file). This works perfectly, and the file is found and delivered. I could debug it with FIrebug, and everything is OK (it displays the contents of the .css inside the opened <link> tag). So, everything working, right? Wrong. It has the CSS, but it does not interpret it! What I mean by this: apparently, the file-type of the CSS (or aplication-type, whatever) is wrong. The Page can access the CSS, but doesnt bother at all to actually use it. What I checked / tried: There are no PHP errors inside of the .css, so that one is out The .css is accessible. I can call the URI manually, or check if the included URL finds it: both works The .css has no syntax errors (i switched to a css that just has body {background-color: #000; } It works whitout NGINX I deleted the browser cache / restarted NGINX after config rewrites Here the configuration: server { listen 80; server_name localhost; access_log /var/log/nginx/board.access_log; error_log /var/log/nginx/board.error_log warn; root /var/www/board/public; index index.php; fastcgi_index index.php; location / { try_files $uri $uri /index.php; } location ~ (\.php|\.css)$ { try_files $uri =404; include /etc/nginx/fastcgi_params; #keepalive_timeout 0; fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; fastcgi_pass 127.0.0.1:7777; } } Firebug 'Network' Response Header: Connection keep-alive Content-Encoding gzip Content-Type text/html Date Sat, 16 Jun 2012 10:08:40 GMT Server nginx/1.0.5 Transfer-Encoding chunked X-Powered-By PHP/5.3.6-13ubuntu3.7 I think I just answered my own question. Is the Content-Type text/html the problem? How can I remove that? My personal guess is that I have to use this in some way include /etc/nginx/mime.types; default_type application/octet-stream; But I'm not sure... anyone an idea how to solve this? TLDR; CSS file is delivered correctly, but it doesnt seem to be 'used' as CSS from the browser. (Tested, works on apache)

  Read the article

• Apache2 & .htaccess : Apache ignoring AccessFile

  - by Elyx0

  Hi there here is my server configuration: DEBIAN 32Bits / PHP 5 / Apache Server version: Apache/2.2.3 - Server built: Mar 22 2008 09:29:10 The AccessFiles : grep -ni AccessFileName * apache2.conf:134:AccessFileName .htaccess apache2.conf:667:AccessFileName .httpdoverride All the AllowOverride statements in my apache2/ folder. mods-available/userdir.conf:6: AllowOverride Indexes AuthConfig Limit mods-available/userdir.conf:16: AllowOverride FileInfo AuthConfig Limit mods-enabled/userdir.conf:6: AllowOverride Indexes AuthConfig Limit mods-enabled/userdir.conf:16: AllowOverride FileInfo AuthConfig Limit sites-enabled/default:8: AllowOverride All sites-enabled/default:14: AllowOverride All sites-enabled/default:19: AllowOverride All sites-enabled/default:24: AllowOverride All sites-enabled/default:42: AllowOverride All The sites-enabled/default file : 1 <VirtualHost *> 2 ServerAdmin [email protected] 3 ServerName mysite.com 4 ServerAlias mysite.com 5 DocumentRoot /var/www/mysite.com/ 6 <Directory /> 7 Options FollowSymLinks 8 AllowOverride All 9 Order Deny,Allow 10 Deny from all 11 </Directory> 12 <Directory /var/www/mysite.com/> 13 Options Indexes FollowSymLinks MultiViews 14 AllowOverride All 15 Order allow,deny 16 allow from all 17 </Directory> 18 <Directory /var/www/mysite.com/test/> 19 AllowOverride All 20 </Directory> 21 22 ScriptAlias /cgi-bin/ /usr/lib/cgi-bin/ 23 <Directory "/usr/lib/cgi-bin"> 24 AllowOverride All 25 Options ExecCGI -MultiViews +SymLinksIfOwnerMatch 26 Order allow,deny 27 Allow from all 28 </Directory> 29 30 ErrorLog /var/log/apache2/error.log 31 32 # Possible values include: debug, info, notice, warn, error, crit, 33 # alert, emerg. 34 LogLevel warn 35 36 CustomLog /var/log/apache2/access.log combined 37 ServerSignature Off 38 39 Alias /doc/ "/usr/share/doc/" 40 <Directory "/usr/share/doc/"> 41 Options Indexes MultiViews FollowSymLinks 42 AllowOverride All 43 Order deny,allow 44 Deny from all 45 Allow from 127.0.0.0/255.0.0.0 ::1/128 46 </Directory> 47 48 49 50 51 52 53 54 </VirtualHost> If i change any Allow from all in Deny from all , it works whenever i put it. I've got one .htaccess at /mysite.com/.htaccess & one at /mysite.com/test/.htaccess with: Order Deny,Allow Deny from all Neither of them work i can still see my website. I've got mod_rewrite enabled but i don't think it does anything here. I've tried almost everything :/ It works on my local environnement (MAMP) but fails when on my Debian server.

  Read the article

• HAProxy causing delay

  - by user1221444

  I am trying to configure HAProxy to do load balancing for a custom webserver I created. Right now I am noticing an increasing delay with HAProxy as the size of the return message increases. For example, I ran four different tests, here are the results: Response 15kb through HAProxy: Avg. response time: .34 secs Transacation rate: 763 trans/sec Throughput: 11.08 MB/sec Response 2kb through HAProxy: Avg. response time: .08 secs Transaction rate: 1171 trans / sec Throughput: 2.51 MB/sec Response 15kb directly to server: Avg. response time: .11 sec Transaction rate: 1046 trans/sec throughput: 15.20 MB/sec Response 2kb directly to server: Avg. Response time: .05 secs Transaction rate: 1158 trans/sec Throughput: 2.48 MB/sec All transactions are HTTP requests. As you can see, there seems to be a much bigger difference between response times for when the response is bigger, than when it is smaller. I understand there will be a slight delay when using HAProxy. Not sure if it matters, but the test itself was run using siege. And during the test there was only one server behind the HAProxy(the same that was used in the direct to server tests). Here is my haproxy.config file: global log 127.0.0.1 local0 log 127.0.0.1 local1 notice maxconn 10000 user haproxy group haproxy daemon #debug defaults log global mode http option httplog option dontlognull retries 3 option redispatch option httpclose maxconn 10000 contimeout 10000 clitimeout 50000 srvtimeout 50000 balance roundrobin stats enable stats uri /stats listen lb1 10.1.10.26:80 maxconn 10000 server app1 10.1.10.200:8080 maxconn 5000 I couldn't find much in terms of options in this file that would help my problem. I have heard suggestions that I may have to adjust a few of my sysctl settings. I could not find a lot of information on this however, most documentation is for Linux 2.4 and 2.6 on the sysctl stuff, I am running 3.2(Ubuntu server 12.04), which seems to auto tuning, so I have no clue what I should or shouldn't be changing. Most settings changes I tried had no effect or a negative effect on performance. Just a notice, this is a very preliminary test, and my hope is that at deployment time, my HAProxy will be able to balance 10k-20k requests/sec to many servers, so if anyone could provide information to help me reach that goal, it would be much appreciated. Thank you very much for any information you can provide. And if you need anymore information from me please let me know, I will get you anything I can.

  Read the article

• SMTP for multiple domains on virtual interfaces

  - by Pawel Goscicki

  The setup is like this (Ubuntu 9.10): eth0: 1.1.1.1 name.isp.com eth0:0 2.2.2.2 example2.com eth0:1 3.3.3.3 example3.com example2.com and example3.com are web apps which need to send emails to their users. 2.2.2.2 points to example2.com and vice-versa (A/PTR). MX - Google. Google handles all incoming mail. 3.3.3.3 points to example3.com and vice-versa (A/PTR). MX - Google. Google handles all incoming mail. Requirements: Local delivery must be disabled (must deliver to MX specified server), so that the following works (note that there is no local user bob on the machine, but there is an existing bob email user): echo "Test" | mail -s "Test 6" [email protected] I need to be able to specify from which IP/domain name the email is delivered when sending an email. I fought with sendmail. With not much luck. Here's some debug info: sendmail -d0.12 -bt < /dev/null Canonical name: name.isp.com UUCP nodename: host a.k.a.: example2.com a.k.a.: example3.com ... Sendmail always uses canonical name (taken from eth0). I've found no way for it to select one of the UUCP codenames. It uses it for sending email: echo -e "To: [email protected]\nSubject: Test\nTest\n" | sendmail -bm -t -v [email protected]... Connecting to [127.0.0.1] via relay... 220 name.isp.com ESMTP Sendmail 8.14.3/8.14.3/Debian-9ubuntu1; Wed, 31 Mar 2010 16:33:55 +0200; (No UCE/UBE) logging access from: localhost(OK)-localhost [127.0.0.1] >>> EHLO name.isp.com I'm ok with other SMTP solutions. I've looked briefly at nbsmtp, msmtp and nullmailer but I'm not sure thay can deal with disabling local delivery and selecting different domains when sending emails. I also know about spoofing sender field by using mail -a "From: <[email protected]>" but it seems to be a half-solution (mails are still sent from isp.com domain instead of proper example2.com, so PTR records are unused and there's more risk of being flagged as spam/spammer).

  Read the article

• Varnish 503 Guru Mediation errors with pfsense and healthy apache

  - by Fammy

  We are running a pfsense firewall / load balancer with varnish as service, In front of Fedora linux webservers running apache. We are getting intermittent 503 guru mediation errors. We are a bit stuck scratching our heads because it is not easily repeatable. The timeouts are set to 30s (connect and first byte) but yet the 503 page will show instantly, not after 30s. Then if you refresh immediately it may very well work instantly and sometimes for a 100 refreshes. The load average on the web servers is < 1, the DB server is < 3 (all servers (web, db, pfsense/varnish) are physical rather than VM. I would have thought if the timeouts were being hit then the 503 page would only appear after 30s am I mistaken? Also when an error happens there does not appear to be any corresponding error in apache's log files. This seems to affect pages as well as images, so it is possible to have the page load fine, and for 9/10 images on the page to be fine but 1 not work An example of the varnish debug is below. It says no backend connection but I can't figure out why, if the load was high on apache I could understand it being flaky The machines are on the same gig ethernet lan 21 ReqStart c *IP-REMOVED* 33418 1274368062 21 RxRequest c GET 21 RxURL c /fashion/ 21 RxProtocol c HTTP/1.1 21 RxHeader c User-Agent: Mozilla/5.0 (X11; U; Linux x86_64; en-US; rv:1.9.0.5) Gecko/2008121622 Fedora/3.0.5-1.fc10 Firefox/3.0.5 21 RxHeader c Host: *ourdomain.com* 21 RxHeader c Accept: */* 21 RxHeader c Accept-Encoding: deflate, gzip 21 VCL_call c recv lookup 21 VCL_call c hash 21 Hash c /fashion/ 21 Hash c *ourdomain.com* 21 VCL_return c hash 21 VCL_call c miss fetch 21 FetchError c no backend connection 21 VCL_call c error restart 21 VCL_call c recv lookup 21 VCL_call c hash 21 Hash c /fashion/ 21 Hash c *ourdomain.com* 21 VCL_return c hash 21 VCL_call c miss fetch 21 FetchError c no backend connection 21 VCL_call c error restart 21 VCL_call c recv lookup 21 VCL_call c hash 21 Hash c /fashion/ 21 Hash c *ourdomain.com* 21 VCL_return c hash 21 VCL_call c miss fetch 21 FetchError c no backend connection 21 VCL_call c error deliver 21 VCL_call c deliver deliver 21 TxProtocol c HTTP/1.1 21 TxStatus c 503 21 TxResponse c Service Unavailable 21 TxHeader c Server: Varnish 21 TxHeader c Content-Type: text/html; charset=utf-8 21 TxHeader c Content-Length: 384 21 TxHeader c Accept-Ranges: bytes 21 TxHeader c Date: Wed, 11 Apr 2012 10:36:17 GMT 21 TxHeader c X-Varnish: 1274368062 21 TxHeader c Age: 0 21 TxHeader c Via: 1.1 varnish 21 TxHeader c Connection: close 21 TxHeader c X-Cache: MISS 21 Length c 384 21 ReqEnd c 1274368062 1334140577.449995041 1334140577.450334787 1.794108152 0.000282764 0.000056982

  Read the article

• How to make local drive available in apache localhost

  - by Ronald Allan

  How can I make my "Drive D:" "Drive E" available in localhost. I'm running apache on my backtrack machine. My default is /var/www/. Every directory I created inside the /var/www/ is available and all working fine. Let's say I created /var/www/PENTEST/ the contents of that PENTEST directory can be accessed through: localhost/PENTEST/ How can I make this work: localhost/media/DATA/ The /media/DATA/ is my DRIVE D: I edited this: ServerAdmin webmaster@localhost DocumentRoot /media/DATA/ <Directory /> Options FollowSymLinks AllowOverride None </Directory> <Directory /media/DATA/> Options Indexes FollowSymLinks MultiViews AllowOverride None Order allow,deny allow from all </Directory> ScriptAlias /cgi-bin/ /usr/lib/cgi-bin/ <Directory "/usr/lib/cgi-bin"> AllowOverride None Options +ExecCGI -MultiViews +SymLinksIfOwnerMatch Order allow,deny Allow from all </Directory> ErrorLog /var/log/apache2/error.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel warn CustomLog /var/log/apache2/access.log combined Alias /doc/ "/usr/share/doc/" <Directory "/usr/share/doc/"> Options Indexes MultiViews FollowSymLinks AllowOverride None Order deny,allow Deny from all Allow from 127.0.0.0/255.0.0.0 ::1/128 </Directory> Still not working. I'm getting 404. # # I figured it out. Thank for the post of "RiggsFolly" which can be found here: http://forum.wampserver.com/read.php?2,89163. I just have to change this: ServerAdmin webmaster@localhost DocumentRoot /media/DATA/ <Directory /> Options FollowSymLinks AllowOverride None </Directory> <Directory /media/DATA/> Options Indexes FollowSymLinks MultiViews AllowOverride None Order allow,deny allow from all </Directory> Into this: ServerAdmin webmaster@localhost DocumentRoot D:/media/DATA/ <Directory /> Options FollowSymLinks AllowOverride None </Directory> <Directory D:/media/DATA/> Options Indexes FollowSymLinks MultiViews AllowOverride None Order allow,deny allow from all </Directory>

  Read the article

• How to configure a tun interface on Linux for SSH port forwarding?

  - by sarshad

  I am trying to forward port 139 from a Windows machine to my Ubuntu SSH server on a tun interface with the ip address 10.0.0.1. This is so that I can access the windows shares on the machine on my Ubuntu server, through the reverse tunnel. I can forward ports to 127.0.0.1, but not to 10.0.0.1. On windows I am using the Tunnelier ssh client. On my Ubuntu server, the following message is printed in auth.log: Received disconnect from 124.109.51.154: 11: Server denied request for client-side server-2-client forwarding on 10.0.0.1:139. So far i have tried the following settings: GatewayPorts yes PermitTunnel yes AllowTcpForwarding yes in the /etc/ssh/sshd_config file, but it did not work. I set up the tun like this: sudo tunctl -t loc_0 -u myusername sudo ifconfig loc_0 inet 10.0.0.1 netmask 255.255.255.0 up The settings in the Tunneler ssh client should not matter because I can forward port 139 successfully to the Microsoft Loopback Adapter on a Windows machine running the WinSSHD server. Versions: Windows is XP SP3, Ubuntu is 10.10. Update: I tried to forward the port to a number greater than 1024 mentioning the IP address of the tun, and it successfully connected but the forwarding was done on 127.0.0.1 instead of the tun's IP address 10.0.0.1. So there are two separate problems now, when connecting from the Windows machine: 1) Forwarding on ports less than 1024 is probably being denied. How can we allow that on the server? 2) Forwarding is done only on 127.0.0.1 even if I mention 10.0.0.1 which is the tun's IP address. Another attempt: I also tried to forward port 22 of a Linux machine to the tun's port 55567. It showed success. But when I tried to ssh into that port using both local addresses, on the Linux machine in its debug display I got the error Connection failed: no route to host when using 127.0.0.1 to connect and simply Connection refused when using the tun's IP address. So the tun is not getting the forwarded port no matter we connect from a Windows client or a Linux client.

  Read the article

• How to force Debian to boot new Kernel?

  - by ThE_-_BliZZarD

  I'm running Debian 6, Debian GNU/Linux, with Linux 2.6.32-5-amd64 under Grub2 ( 1.98+20100804-14+squeeze1) on a remote system (no possibility to view the pre-boot messages). I compiled and installed a new kernel, but I can not get it to boot. What I have done: Installed the packages via: dpkg -i linux-headers-3.5.3.20120914-amd64_3.5.3.20120914-amd64-10.00.Custom_amd64.deb linux-image-3.5.3.20120914-amd64_3.5.3.20120914-amd64-10.00.Custom_amd64.deb This updated the Grub configuration. My /boot/grub/grub.cfg now contains: menuentry 'Debian GNU/Linux, with Linux 3.5.3.20120914-amd64' --class debian --class gnu-linux --class gnu --class os { insmod raid insmod mdraid insmod part_msdos insmod part_msdos insmod ext2 set root='(md0)' search --no-floppy --fs-uuid --set 5a3882a9-c7df-4f6a-9feb-f03e3e37be01 echo 'Loading Linux 3.5.3.20120914-amd64 ...' linux /vmlinuz-3.5.3.20120914-amd64 root=UUID=003242b5-121b-49f3-b32f-1b40aea56eed ro acpi=ht quiet panic=10 echo 'Loading initial ramdisk ...' initrd /initrd.img-3.5.3.20120914-amd64 } menuentry 'Debian GNU/Linux, with Linux 2.6.32-5-amd64' --class debian --class gnu-linux --class gnu --class os { insmod raid insmod mdraid insmod part_msdos insmod part_msdos insmod ext2 set root='(md0)' search --no-floppy --fs-uuid --set 5a3882a9-c7df-4f6a-9feb-f03e3e37be01 echo 'Loading Linux 2.6.32-5-amd64 ...' linux /vmlinuz-2.6.32-5-amd64 root=UUID=003242b5-121b-49f3-b32f-1b40aea56eed ro acpi=ht quiet panic=10 echo 'Loading initial ramdisk ...' initrd /initrd.img-2.6.32-5-amd64 } I used grub-set-default "Debian GNU/Linux, with Linux 2.6.32-5-amd64" to set the old kernel as default and then grub-reboot "Debian GNU/Linux, with Linux 3.5.3.20120914-amd64" to boot into the new kernel once. After update-grub I rebooted the system, but everytime it comes back up with the old kernel (2.6). I tried setting the new one as default (grub-set-default 0, update-grub, reboot) but, still the old one. The Syslogs contain NO hint whatsoever about trying to boot the new kernel - only the old one. Would there be any hints regarding problems with a kernel? Is there a way to enable debug-logging in grub? What am I doing wrong? How can I force the system to boot the new kernel? Edit: Hardware of remote machine. CPU cat /proc/cpuinfo processor : 0 vendor_id : AuthenticAMD cpu family : 16 model : 5 model name : AMD Athlon(tm) II X4 605e Processor stepping : 3 cpu MHz : 2294.898 cache size : 512 KB physical id : 0 siblings : 4 core id : 0 cpu cores : 4 apicid : 0 initial apicid : 0 fpu : yes fpu_exception : yes cpuid level : 5 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush mmx fxsr sse sse2 ht syscall nx mmxext fxsr_opt pdpe1gb rdtscp lm 3dnowext 3dnow constant_tsc rep_good nonstop_tsc extd_apicid pni monitor cx16 popcnt lahf_lm cmp_legacy svm extapic cr8_legacy abm sse4a misalignsse 3dnowprefetch osvw ibs skinit wdt bogomips : 4589.77 TLB size : 1024 4K pages clflush size : 64 cache_alignment : 64 address sizes : 48 bits physical, 48 bits virtual power management: ts ttp tm stc 100mhzsteps hwpstate (copied only the first, 3 more follow) The server is a Fujitsu PRIMERGY MX130 S1.

  Read the article

• After compiling PHP, I get mod_fcgid: error reading data from FastCGI server

  - by user34295

  I'm trying to add multiple PHP version in Plesk 12. Switching my domain to the new version PHP 5.4.29 result in this error: (104)Connection reset by peer: mod_fcgid: error reading data from FastCGI server Here is phpinfo() of the complied PHP version, obtained running php54-cgi index.php from the terminal. The same script placed under document root doesn't work in FastCGI. How can I debug/try to figure out what's the error? Currently running CentOS 6.5 x64, Plesk v12.0.18_build1200140529.2, PHP 5.5.13. I've downloaded PHP 5.4.29: cd /usr/local/src curl -O http://it1.php.net/distributions/php-5.4.29.tar.gz cd php-5.4.29 And configured with: ./configure \ --prefix=/usr/local/php54 \ --with-bz2 \ --with-config-file-path=/usr/local/php54/etc \ --with-config-file-scan-dir=/usr/local/php54/etc/php.d \ --with-curl \ --with-gd \ --with-gettext \ --with-iconv \ --with-layout=PHP \ --with-libxml-dir=/usr/local/php54 \ --with-mhash \ --with-mysql=mysqlnd \ --with-mysqli=mysqlnd \ --with-openssl \ --with-pdo-mysql=mysqlnd \ --with-readline \ --with-xsl \ --with-zlib \ --enable-calendar \ --enable-cgi \ --enable-exif \ --enable-ftp \ --enable-intl \ --enable-mbstring \ --enable-pcntl \ --enable-shmop \ --enable-sockets \ --enable-sockets \ --enable-sysvmsg \ --enable-sysvsem \ --enable-sysvshm \ --enable-wddx \ --enable-zip Then: make && make install Installing PHP CLI binary: /usr/local/php54/bin/ Installing PHP CLI man page: /usr/local/php54/php/man/man1/ Installing PHP CGI binary: /usr/local/php54/bin/ Installing PHP CGI man page: /usr/local/php54/php/man/man1/ Installing build environment: /usr/local/php54/lib/php/build/ Installing header files: /usr/local/php54/include/php/ Installing helper programs: /usr/local/php54/bin/ program: phpize program: php-config Installing man pages: /usr/local/php54/php/man/man1/ page: phpize.1 page: php-config.1 Installing PEAR environment: /usr/local/php54/lib/php/ [PEAR] Archive_Tar - installed: 1.3.11 [PEAR] Console_Getopt - installed: 1.3.1 warning: pear/PEAR requires package "pear/Structures_Graph" (recommended version 1.0.4) warning: pear/PEAR requires package "pear/XML_Util" (recommended version 1.2.1) [PEAR] PEAR - installed: 1.9.4 Wrote PEAR system config file at: /usr/local/php54/etc/pear.conf You may want to add: /usr/local/php54/lib/php to your php.ini include_path [PEAR] Structures_Graph- installed: 1.0.4 [PEAR] XML_Util - installed: 1.2.1 /usr/local/src/php-5.4.29/build/shtool install -c ext/phar/phar.phar /usr/local/php54/bin ln -s -f /usr/local/php54/bin/phar.phar /usr/local/php54/bin/phar Installing PDO headers: /usr/local/php54/include/php/ext/pdo/ Copied php.ini-production to /usr/local/php54/etc/php.ini and added a new handler in Plesk: /usr/local/psa/bin/php_handler --add -displayname 5.4.29 -path /usr/local/php54/bin/php-cgi -phpini /usr/local/php54/etc/php.ini -type fastcgi -id php54 Symbolic linking: ln -s /usr/local/php54/bin/php /usr/local/bin/php54 ln -s /usr/local/php54/bin/php-cgi /usr/local/bin/php54-cgi New installed version: php54-cgi -m [PHP Modules] bz2 calendar cgi-fcgi Core ctype curl date dom ereg exif fileinfo filter ftp gd gettext hash iconv intl json libxml mbstring mhash mysql mysqli mysqlnd openssl pcntl pcre PDO pdo_mysql pdo_sqlite Phar posix readline Reflection session shmop SimpleXML sockets SPL sqlite3 standard sysvmsg sysvsem sysvshm tokenizer wddx xml xmlreader xmlwriter xsl zip zlib [Zend Modules]

  Read the article

• Empty $_POST data

  - by Antimony

  I am trying to post a post to my MyBB server from a Python script, but try as I might, I can't get it to work. The request shows up in the forensic log and the headers are in the $_SERVER variable, but $_POST is always an empty array. The error log shows nothing, even at the debug level. I've already tried searching, but I haven't found anything that's helped. I already checked the post_max_size thing, which is 8M. Another factor is that it's just my own requests which aren't going through. Browser generated requests seem to do just fine. I've looked and looked, but I can't find anything I'm doing differently that should matter. Anyway, here is an example request. POST /newreply.php?tid=1&processed=1 HTTP/1.1 Host: <redacted> Accept-Encoding: identity Content-Length: 1153 Content-Type: multipart/form-data; boundary=-->0xa216654L Cookie: sid=<redacted>; mybb[lastvisit]=1354995469; mybb[lastactive]=1354995500; mybb[threadread]=a%3A1%3A%7Bi%3A1%3Bi%3A1354995469%3B%7D; mybb[forumread]=a%3A1%3A%7Bi%3A2%3Bi%3A1354995469%3B%7D; loginattempts=1; mybbuser=2_ZlVVfaYS9FstZGQzr4KiNRUm3Z4xAgJkTPPq2ouFcuaragOTVQ Accept: text/html User-Agent: Mozilla/5.0 (Windows NT 6.1; rv:14.0) Gecko/20100101 Firefox/14.0.1 -->0xa216654L Content-Disposition: form-data; name="my_post_key" 257b2bbef4334000d9088169154900a3 -->0xa216654L Content-Disposition: form-data; name="quoted_ids" -->0xa216654L Content-Disposition: form-data; name="tid" 1 -->0xa216654L Content-Disposition: form-data; name="message" foo!2 -->0xa216654L Content-Disposition: form-data; name="attachmentact" -->0xa216654L Content-Disposition: form-data; name="attachmentaid" -->0xa216654L Content-Disposition: form-data; name="icon" -1 -->0xa216654L Content-Disposition: form-data; name="posthash" e93a2c78ce3f6807a86fd475ef4178cf -->0xa216654L Content-Disposition: form-data; name="postoptions[subscriptionmethod]" -->0xa216654L Content-Disposition: form-data; name="replyto" -->0xa216654L Content-Disposition: form-data; name="message_new" foo!2 -->0xa216654L Content-Disposition: form-data; name="submit" Post Reply -->0xa216654L Content-Disposition: form-data; name="attachment"; filename="" Content-Type: application/octet-stream -->0xa216654L Content-Disposition: form-data; name="action" do_newreply -->0xa216654L Content-Disposition: form-data; name="subject" Lol -->0xa216654L

  Read the article

• High I/O latency with software RAID, LUKS encrypted and LVM partitioned KVM setup

  - by aef

  I found out a performance problems with a Mumble server, which I described in a previous question are caused by an I/O latency problem of unknown origin. As I have no idea what is causing this and how to further debug it, I'm asking for your ideas on the topic. I'm running a Hetzner EX4S root server as KVM hypervisor. The server is running Debian Wheezy Beta 4 and KVM virtualisation is utilized through LibVirt. The server has two different 3TB hard drives as one of the hard drives was replaced after S.M.A.R.T. errors were reported. The first hard disk is a Seagate Barracuda XT ST33000651AS (512 bytes logical, 4096 bytes physical sector size), the other one a Seagate Barracuda 7200.14 (AF) ST3000DM001-9YN166 (512 bytes logical and physical sector size). There are two Linux software RAID1 devices. One for the unencrypted boot partition and one as container for the encrypted rest, using both hard drives. Inside the latter RAID device lies an AES encrypted LUKS container. Inside the LUKS container there is a LVM physical volume. The hypervisor's VFS is split on three logical volumes on the described LVM physical volume: one for /, one for /home and one for swap. Here is a diagram of the block device configuration stack: sda (Physical HDD) - md0 (RAID1) - md1 (RAID1) sdb (Physical HDD) - md0 (RAID1) - md1 (RAID1) md0 (Boot RAID) - ext4 (/boot) md1 (Data RAID) - LUKS container - LVM Physical volume - LVM volume hypervisor-root - LVM volume hypervisor-home - LVM volume hypervisor-swap - … (Virtual machine volumes) The guest systems (virtual machines) are mostly running Debian Wheezy Beta 4 too. We have one additional Ubuntu Precise instance. They get their block devices from the LVM physical volume, too. The volumes are accessed through Virtio drivers in native writethrough mode. The IO scheduler (elevator) on both the hypervisor and the guest system is set to deadline instead of the default cfs as that happened to be the most performant setup according to our bonnie++ test series. The I/O latency problem is experienced not only inside the guest systems but is also affecting services running on the hypervisor system itself. The setup seems complex, but I'm sure that not the basic structure causes the latency problems, as my previous server ran four years with almost the same basic setup, without any of the performance problems. On the old setup the following things were different: Debian Lenny was the OS for both hypervisor and almost all guests Xen software virtualisation (therefore no Virtio, also) no LibVirt management Different hard drives, each 1.5TB in size (one of them was a Seagate Barracuda 7200.11 ST31500341AS, the other one I can't tell anymore) We had no IPv6 connectivity Neither in the hypervisor nor in guests we had noticable I/O latency problems According the the datasheets, the current hard drives and the one of the old machine have an average latency of 4.12ms.

  Read the article

• Starting php-cgi at boot on mac os x 10.6.8

  - by nikhil

  I'm new to mac os, I have installed and configured nginx with php-fastcgi. I need to run this command in a terminal and keep that terminal open to access php files from my browser. php-cgi -b 127.0.0.1:9000 -q Here's the plist that I wrote by looking up sources on the internet <?xml version="1.0" encoding="UTF-8"?> <!DOCTYPE plist PUBLIC "-//Apple//DTD PLIST 1.0//EN" "http://www.apple.com/DTDs/PropertyList-1.0.dtd"> <plist version="1.0"> <dict> <key>Debug</key> <false/> <key>EnvironmentVariables</key> <dict> <key>PHP_FCGI_CHILDREN</key> <string>2</string> <key>PHP_FCGI_MAX_REQUESTS</key> <string>1000</string> </dict> <key>RunAtLoad</key> <true/> <key>KeepAlive</key> <true/> <key>UserName</key> <string>nikhil</string> <key>Label</key> <string>php-fastcgi</string> <key>ProgramArguments</key> <array> <string>/usr/bin/php-cgi</string> <string>-b 127.0.0.1:9000</string> <string>-q</string> </array> </dict> </plist> I'm loading it using launchctl load -w ~/Library/LaunchAgents/php-fastcgi.plist without any success, can anyone tell me how this can be done.

  Read the article

• Problem connecting to SSH in office network

  - by Jeune

  I have trouble connecting via SSH to a server whenever I am in the office. I get as far as being prompted for my password and then after that there's a long wait which always ends in a Write failed: Broken pipe This is only for connecting via SSH. I use svn to commit files to a repository hosted on the same server and there are no hitches. Furthermore, this only happens in our office. When I go the university or whenever I am at home or at the coffee shop I am able to connect seamlessly. There are no firewalls in our office. It's just a basic wireless router connected to a modem setup. It's the same setup I have at home and I guess the same setup in the coffee shop. What are the causes for a broken pipe and why does this phenomenon only happen when I try connect via SSH and not when I work with svn on the same server? Updated: Some debug logs after authentication: debug3: packet_send2: adding 48 (len 64 padlen 16 extra_pad 64) debug2: we sent a password packet, wait for reply debug1: Authentication succeeded (password). debug1: channel 0: new [client-session] debug3: ssh_session2_open: channel_new: 0 debug2: channel 0: send open debug1: Entering interactive session. debug2: callback start debug2: client_session2_setup: id 0 debug2: channel 0: request pty-req confirm 1 debug1: Sending environment. debug3: Ignored env ORBIT_SOCKETDIR debug3: Ignored env SSH_AGENT_PID debug3: Ignored env TERM debug3: Ignored env SHELL debug3: Ignored env XDG_SESSION_COOKIE debug3: Ignored env WINDOWID debug3: Ignored env GNOME_KEYRING_CONTROL debug3: Ignored env GTK_MODULES debug3: Ignored env USER debug3: Ignored env LS_COLORS debug3: Ignored env LIBGL_DRIVERS_PATH debug3: Ignored env SSH_AUTH_SOCK debug3: Ignored env DEFAULTS_PATH debug3: Ignored env SESSION_MANAGER debug3: Ignored env USERNAME debug3: Ignored env XDG_CONFIG_DIRS debug3: Ignored env DESKTOP_SESSION debug3: Ignored env LIBGL_ALWAYS_INDIRECT debug3: Ignored env PATH debug3: Ignored env PWD debug3: Ignored env GDM_KEYBOARD_LAYOUT debug1: Sending env LANG = en_PH.utf8 debug2: channel 0: request env confirm 0 debug3: Ignored env GNOME_KEYRING_PID debug3: Ignored env MANDATORY_PATH debug3: Ignored env GDM_LANG debug3: Ignored env GDMSESSION debug3: Ignored env SHLVL debug3: Ignored env HOME debug3: Ignored env GNOME_DESKTOP_SESSION_ID debug3: Ignored env LOGNAME debug3: Ignored env XDG_DATA_DIRS debug3: Ignored env DBUS_SESSION_BUS_ADDRESS debug3: Ignored env LESSOPEN debug3: Ignored env WINDOWPATH debug3: Ignored env DISPLAY debug3: Ignored env LESSCLOSE debug3: Ignored env XAUTHORITY debug3: Ignored env COLORTERM debug3: Ignored env OLDPWD debug3: Ignored env _ debug2: channel 0: request shell confirm 1 debug2: fd 3 setting TCP_NODELAY debug2: callback done debug2: channel 0: open confirm rwindow 0 rmax 32768 UPDATE 2011-14-07: I am able to connect to the server via SSH now. I didn't do anything but that's because there is no one in the office but me! Having said that, is it possible that it has something to do with the number of sessions an SSH server can handle? UPDATE 2011-14-07: I try to login via SSH through Putty on another machine running windows together with my current SSH session in Ubuntu and now it seems my SSH session in Ubuntu has been dropped. I can't type into the terminal. Is Putty the culprit now?

  Read the article

• 502 Bad Gateway with nginx + apache + subversion + ssl (SVN COPY)

  - by theplatz

  I've asked this on stackoverflow, but it may be better suited for serverfault... I'm having a problem running Apache + Subversion with SSL behind an Nginx proxy and I'm hoping someone might have the answer. I've scoured google for hours looking for the answer to my problem and can't seem to figure it out. What I'm seeing are "502 (Bad Gateway)" errors when trying to MOVE or COPY using subversion; however, checkouts and commits work fine. Here are the relevant parts (I think) of the nginx and apache config files in question: Nginx upstream subversion_hosts { server 127.0.0.1:80; } server { listen x.x.x.x:80; server_name hostname; access_log /srv/log/nginx/http.access_log main; error_log /srv/log/nginx/http.error_log info; # redirect all requests to https rewrite ^/(.*)$ https://hostname/$1 redirect; } # HTTPS server server { listen x.x.x.x:443; server_name hostname; passenger_enabled on; root /path/to/rails/root; access_log /srv/log/nginx/ssl.access_log main; error_log /srv/log/nginx/ssl.error_log info; ssl on; ssl_certificate server.crt; ssl_certificate_key server.key; add_header Front-End-Https on; location /svn { proxy_set_header Host $host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; set $fixed_destination $http_destination; if ( $http_destination ~* ^https(.*)$ ) { set $fixed_destination http$1; } proxy_set_header Destination $fixed_destination; proxy_pass http://subversion_hosts; } } Apache Listen 127.0.0.1:80 <VirtualHost *:80> # in order to support COPY and MOVE, etc - over https (443), # ServerName _must_ be the same as the nginx servername # http://trac.edgewall.org/wiki/TracNginxRecipe ServerName hostname UseCanonicalName on <Location /svn> DAV svn SVNParentPath "/srv/svn" Order deny,allow Deny from all Satisfy any # Some config omitted ... </Location> ErrorLog /var/log/apache2/subversion_error.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel warn CustomLog /var/log/apache2/subversion_access.log combined </VirtualHost> From what I could tell while researching this problem, the server name has to match on both the apache server as well as the nginx server, which I've done. Additionally, this problem seems to stick around even if I change the configuration to use http only.

  Read the article

• iptables & allowed port refusing connection

  - by marfarma

  Can you see what I'm doing wrong? On Ubuntu Server 9.1, I'm attempting to allow traffic on port 1143 for a non-privileged IMAP host. Connection is refused when testing with telnet example.com 1143 but connection is allowed testing with telnet example.com 80 from my pc to remote internet hosted server. Both rules appear identical and are located near each other with no rules rejecting connections intervening in the rules file. I can't figure it out. iptables -L returns this: Chain INPUT (policy ACCEPT) target prot opt source destination ACCEPT all -- anywhere anywhere REJECT all -- anywhere 127.0.0.0/8 reject-with icmp-port-unreachable ACCEPT all -- anywhere anywhere state RELATED,ESTABLISHED ACCEPT tcp -- anywhere anywhere tcp dpt:www ACCEPT tcp -- anywhere anywhere tcp dpt:https ACCEPT tcp -- anywhere anywhere tcp dpt:http-alt ACCEPT tcp -- anywhere anywhere tcp dpt:7070 ACCEPT tcp -- anywhere anywhere tcp dpt:1143 ACCEPT tcp -- anywhere anywhere state NEW tcp dpt:ssh ACCEPT icmp -- anywhere anywhere icmp echo-request LOG all -- anywhere anywhere limit: avg 5/min burst 5 LOG level debug prefix `iptables denied: ' REJECT all -- anywhere anywhere reject-with icmp-port-unreachable Chain FORWARD (policy ACCEPT) target prot opt source destination REJECT all -- anywhere anywhere reject-with icmp-port-unreachable Chain OUTPUT (policy ACCEPT) target prot opt source destination ACCEPT all -- anywhere anywhere and my rules file contains this: # Generated by iptables-save v1.4.4 on Wed May 26 19:08:34 2010 *nat :PREROUTING ACCEPT [3556:217296] :POSTROUTING ACCEPT [6909:414847] :OUTPUT ACCEPT [6909:414847] -A PREROUTING -p tcp -m tcp --dport 80 -j REDIRECT --to-ports 8080 -A PREROUTING -p tcp -m tcp --dport 80 -j REDIRECT --to-ports 8080 COMMIT # Completed on Wed May 26 19:08:34 2010 # Generated by iptables-save v1.4.4 on Wed May 26 19:08:34 2010 *filter :INPUT ACCEPT [1:52] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [1:212] -A INPUT -i lo -j ACCEPT -A INPUT -d 127.0.0.0/8 ! -i lo -j REJECT --reject-with icmp-port-unreachable -A INPUT -m state --state RELATED,ESTABLISHED -j ACCEPT -A INPUT -p tcp -m tcp --dport 80 -j ACCEPT -A INPUT -p tcp -m tcp --dport 443 -j ACCEPT -A INPUT -p tcp -m tcp --dport 8080 -j ACCEPT -A INPUT -p tcp -m tcp --dport 7070 -j ACCEPT -A INPUT -p tcp -m tcp --dport 1143 -j ACCEPT -A INPUT -p tcp -m state --state NEW -m tcp --dport 22 -j ACCEPT -A INPUT -p icmp -m icmp --icmp-type 8 -j ACCEPT -A INPUT -m limit --limit 5/min -j LOG --log-prefix "iptables denied: " --log-level 7 -A INPUT -j REJECT --reject-with icmp-port-unreachable -A FORWARD -j REJECT --reject-with icmp-port-unreachable -A OUTPUT -j ACCEPT COMMIT # Completed on Wed May 26 19:08:34 2010

  Read the article

• Server hung with "blocked for more than 120 seconds", diskless

  - by alterpub

  I have server which hung every 2-5 days. dmesg show following situation: kernel: [490894.231753] INFO: task munin-html:10187 blocked for more than 120 seconds. kernel: [490894.231799] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. kernel: [490894.231843] munin-html D 0000000000000000 0 10187 9796 0x00000000 kernel: [490894.231878] ffff88063174b968 0000000000000082 ffff88063174b8d8 0000000000015b80 kernel: [490894.231930] ffff88063174bfd8 0000000000015b80 ffff88063174bfd8 ffff88062fe644d0 kernel: [490894.231982] 0000000000015b80 0000000000015b80 ffff88063174bfd8 0000000000015b80 kernel: [490894.232033] Call Trace: kernel: [490894.232059] [<ffffffff8117fce0>] ? sync_buffer+0x0/0x50 kernel: [490894.232089] [<ffffffff815a1f13>] io_schedule+0x73/0xc0 kernel: [490894.232115] [<ffffffff8117fd25>] sync_buffer+0x45/0x50 kernel: [490894.232143] [<ffffffff815a258f>] __wait_on_bit+0x5f/0x90 kernel: [490894.232170] [<ffffffff8117fce0>] ? sync_buffer+0x0/0x50 kernel: [490894.232197] [<ffffffff815a2638>] out_of_line_wait_on_bit+0x78/0x90 kernel: [490894.232227] [<ffffffff81080250>] ? wake_bit_function+0x0/0x40 kernel: [490894.232255] [<ffffffff8117fcd6>] __wait_on_buffer+0x26/0x30 kernel: [490894.232288] [<ffffffffa00131be>] squashfs_read_data+0x1be/0x520 [squashfs] kernel: [490894.232320] [<ffffffff8114f0f1>] ? __mem_cgroup_try_charge+0x71/0x450 kernel: [490894.232350] [<ffffffffa0013963>] squashfs_cache_get+0x1c3/0x320 [squashfs] kernel: [490894.232381] [<ffffffffa00136eb>] ? squashfs_copy_data+0x10b/0x130 [squashfs] kernel: [490894.232426] [<ffffffff815a3dbe>] ? _raw_spin_lock+0xe/0x20 kernel: [490894.232454] [<ffffffffa0013b68>] ? squashfs_read_metadata+0x48/0xf0 [squashfs] kernel: [490894.232499] [<ffffffffa0013ae1>] squashfs_get_datablock+0x21/0x30 [squashfs] kernel: [490894.232544] [<ffffffffa0015026>] squashfs_readpage+0x436/0x4a0 [squashfs] kernel: [490894.232575] [<ffffffff8111a375>] ? __inc_zone_page_state+0x35/0x40 kernel: [490894.232606] [<ffffffff8110d072>] __do_page_cache_readahead+0x172/0x210 kernel: [490894.232636] [<ffffffff8110d131>] ra_submit+0x21/0x30 kernel: [490894.232662] [<ffffffff811045f3>] filemap_fault+0x3f3/0x450 kernel: [490894.232691] [<ffffffff812bd156>] ? prio_tree_insert+0x256/0x2b0 kernel: [490894.232726] [<ffffffffa009225d>] aufs_fault+0x11d/0x170 [aufs] kernel: [490894.232755] [<ffffffff8111f6d4>] __do_fault+0x54/0x560 kernel: [490894.232782] [<ffffffff81122f39>] handle_mm_fault+0x1b9/0x440 kernel: [490894.232811] [<ffffffff811286f5>] ? do_mmap_pgoff+0x335/0x380 kernel: [490894.232840] [<ffffffff815a7af5>] do_page_fault+0x125/0x350 kernel: [490894.232867] [<ffffffff815a4675>] page_fault+0x25/0x30 Os info cat /etc/issue.net Ubuntu 10.04.2 LTS uname -a Linux Shard1Host3 2.6.35-32-server #68~lucid1-Ubuntu SMP Wed Mar 28 18:33:00 UTC 2012 x86_64 GNU/Linux This system load via ltsp and hasn't harddrives also it has a lot of memory 24Gb. free -m total used free shared buffers cached Mem: 24152 17090 7061 0 50 494 -/+ buffers/cache: 16545 7607 Swap: 0 0 0 I put vmstat info here but I think it won't give results after reboot vmstat 1 30 procs -----------memory---------- ---swap-- -----io---- -system-- ----cpu---- r b swpd free buff cache si so bi bo in cs us sy id wa 0 0 0 7231156 52196 506400 0 0 0 0 172 143 7 0 92 0 1 0 0 7231024 52196 506400 0 0 0 0 7859 16233 5 0 94 0 0 0 0 7231024 52196 506400 0 0 0 0 7870 16446 2 0 98 0 0 0 0 7230900 52196 506400 0 0 0 0 7308 15661 5 0 95 0 0 0 0 7231100 52196 506400 0 0 0 0 7960 16543 6 0 94 0 0 0 0 7231100 52196 506400 0 0 0 0 7542 16047 5 1 94 0 3 0 0 7231100 52196 506400 0 0 0 0 7709 16621 3 0 96 0 0 0 0 7231220 52196 506400 0 0 0 0 7857 16552 4 0 96 0 0 0 0 7231220 52196 506400 0 0 0 0 7192 15491 6 0 94 0 0 0 0 7231220 52196 506400 0 0 0 0 7423 15792 5 1 94 0 1 0 0 7231260 52196 506404 0 0 0 0 7686 16296 2 0 98 0 0 0 0 7231260 52196 506404 0 0 0 0 6976 15183 5 0 95 0 0 0 0 7231260 52196 506404 0 0 0 0 7303 15600 4 0 95 0 0 0 0 7231320 52196 506404 0 0 0 0 7967 16241 1 0 98 0 0 0 0 7231444 52196 506404 0 0 0 0 6948 15113 6 0 94 0 0 0 0 7231444 52196 506404 0 0 0 0 7931 16181 6 0 94 0 1 0 0 7231516 52196 506404 0 0 0 0 7715 15829 6 0 94 0 0 0 0 7231516 52196 506404 0 0 0 0 7771 16036 2 0 97 0 0 0 0 7231268 52196 506404 0 0 0 0 7782 16202 6 0 94 0 1 0 0 7231212 52196 506404 0 0 0 0 7457 15622 4 0 96 0 0 0 0 7231212 52196 506404 0 0 0 0 7573 16045 2 0 98 0 2 0 0 7231216 52196 506404 0 0 0 0 7689 16076 6 0 94 0 0 0 0 7231424 52196 506404 0 0 0 0 7429 15650 4 0 95 0 3 0 0 7231424 52196 506404 0 0 0 0 7534 16168 3 0 97 0 1 0 0 7230548 52196 506404 0 0 0 0 8559 15926 7 1 92 0 0 0 0 7230672 52196 506404 0 0 0 0 7720 15905 2 0 98 0 0 0 0 7230548 52196 506404 0 0 0 0 7677 16313 5 0 95 0 1 0 0 7230676 52196 506404 0 0 0 0 7209 15432 5 0 95 0 0 0 0 7230800 52196 506404 0 0 0 0 7522 15861 2 0 98 0 0 0 0 7230552 52196 506404 0 0 0 0 7760 16661 5 0 95 0 In the munin(monitoring system) graphs I see(before server hung): Disk(nbd0) IOs per device: read: 289m but avg by week 2.09m Disk(nbd0) throughput per device: read: 4.73k but avg by week 108.76 Disk(nbd0) utilization per device: 100% but avg by week 1.2% Eth0 traffic was low: in/out only 2Mbps Number of threads increased to 566 usually 392 Fork rate 1.08 but usually 2.82 VMStat(processes state) Increased to 17.77(from 0 as far as I could see in the graph) CPU usage iowait 880.46% when usually 6.67% It'll be great if somebody help me to understand what's up.

  Read the article

• Why is mount -a not mounting fuse drive properly when executed remotely (via Fabric)?

  - by Jim D

  This is a weird bug and I'm not sure where it's coming from. Here's a quick run down of what I'm doing. I'm trying to mount a FUSE drive to an Amazon EC2 instance running Ubuntu 10.10 using s3fs (FUSE over Amazon). s3fs is compiled from source according to the instructions etc. I've also added an entry to /etc/fstab so that the drive mounts on boot. Here's what /etc/fstab looks like: # /etc/fstab: static file system information. # <file system> <mount point> <type> <options> <dump> <pass> proc /proc proc nodev,noexec,nosuid 0 0 LABEL=uec-rootfs / ext4 defaults 0 0 /dev/sda2 /mnt auto defaults,nobootwait,comment=cloudconfig 0 2 /dev/sda3 none swap sw,comment=cloudconfig 0 0 s3fs#mybucket /mnt/s3/mybucket fuse default_acl=public-read,use_cache=/tmp,allow_other 0 0 So the good news is that this works fine. On reboot the connection mounts correctly. I can also do: $ sudo umount /mnt/s3/mybucket $ sudo mount -a $ mountpoint /mnt/s3/mybucket /mnt/s3/mybucket is a mountpoint Great, right? Well here's the problem. I'm using Fabric to automate the process of building and managing this instance. I noticed I was getting this error message when using Fabric to build s3fs and set up the mount process: mountpoint: /mnt/s3/mybucket: Transport endpoint is not connected I isolated it down the the problem and built a fabric task that reproduces the problem: def remount_s3fs(): sudo("mount -a") Which does: [ec2-xx-xx-xx-xx.compute-1.amazonaws.com] Executing task 'remount_s3fs' [ec2-xx-xx-xx-xx.compute-1.amazonaws.com] sudo: mount -a [And yes, I was sure to unmount it before running this task.] When I check the mount using mountpoint I get: $ mountpoint /mnt/s3/mybucket mountpoint: /mnt/s3/mybucket: Transport endpoint is not connected Done. But if I run sudo mount -a at the command line, it works. Hrm. Here is that fab task output again, this time in full debug mode: [ec2-xx-xx-xx-xx.compute-1.amazonaws.com] Executing task 'remount_s3fs' [ec2-xx-xx-xx-xx.compute-1.amazonaws.com] sudo: sudo -S -p 'sudo password:' /bin/bash -l -c "mount -a" Again, I get that transport endpoint not connected error. I've also tried copying and pasting the exact command run into my ssh session (i.e. sudo -S -p 'sudo password:' /bin/bash -l -c "mount -a") and it works fine. So...that's my problem. Any ideas?

  Read the article

< Previous Page | 341 342 343 344 345 346 347 348 349 350 351 352  | Next Page >