Search Results

Search found 11982 results on 480 pages for 'non greedy'.

Page 348/480 | < Previous Page | 344 345 346 347 348 349 350 351 352 353 354 355  | Next Page >

  • Mainboard shuts itself off after half a second or so

    - by heishe
    Here's the problem: When I start the PC, the mainboard powers up, then stays that way maybe 0.2-0.5 seconds, and then shuts off again. I say mainboard, and not PC, because I removed all the parts from the system and disconnected everything but the mainboard power supply (the broad 12 pin thingy). When I have the other parts (cpu, graphics card, ram, etc.) installed and connected, the basic behaviour stays the same, but now the mainboard runs for about 6 or 7 seconds (this is a guess) before shutting off. This all started when my monitor wouldn't receive a video signal today, without giving POSTs, so I took the graphics card and the RAM out to see if it changes anything. It didn't, except that from that point on the mainboard would start to have this behavior where it just stays on for a very short time and then shuts off again. I already tested it with a backup PSU - same behavior. What could this be? I'm thinking it can't be on a physical level (transistors burned through or something like that), since then the mainboard either shouldn't start at all or it should detect hardware failures in non-essential parts of the syste and start beeping. Sorry, I forgot to mention. It's an MSI P67A-C43. I already checked the capacitors if someone popped, but I can't find anything. I also tried resetting the cmos, but that didn't change anything.

    Read the article

  • Trying to build OpenSimulator.. nant fails

    - by Gary
    Output of nant is: Buildfile: file:///root/opensim-0.6.8-release/OpenSim.build Target framework: Mono 2.0 Profile Target(s) specified: build [echo] Using 'mono-2.0' Framework init: Debug: [echo] Platform unix build: [nant] /root/opensim-0.6.8-release/OpenSim/Framework/Servers/HttpServer/OpenSim.Framework.Servers.HttpServer.dll.build build Buildfile: file:///root/opensim-0.6.8-release/OpenSim/Framework/Servers/HttpServer/OpenSim.Framework.Servers.HttpServer.dll.build Target framework: Mono 2.0 Profile Target(s) specified: build build: [echo] Build Directory is /root/opensim-0.6.8-release/OpenSim/Framework/Servers/HttpServer/bin/Debug [csc] Compiling 29 files to '/root/opensim-0.6.8-release/OpenSim/Framework/Servers/HttpServer/bin/Debug/OpenSim.Framework.Servers.HttpServer.dll'. [csc] /root/opensim-0.6.8-release/OpenSim/Framework/Servers/HttpServer/AsynchronousRestObjectRequester.cs(103,41): error CS0246: The type or namespace name `TResponse' could not be found. Are you missing a using directive or an assembly reference? [csc] Compilation failed: 1 error(s), 0 warnings BUILD FAILED - 0 non-fatal error(s), 1 warning(s) /root/opensim-0.6.8-release/OpenSim/Framework/Servers/HttpServer/OpenSim.Framework.Servers.HttpServer.dll.build(14,6): External Program Failed: /usr/lib/pkgconfig/../../lib/mono/2.0/gmcs.exe (return code was 1) Total time: 1.2 seconds. BUILD FAILED Nested build failed. Refer to build log for exact reason. Total time: 1.3 seconds. OS is Fedora 7. Any ideas appreciated. :)

    Read the article

  • SSL with nginx on subdomain not working

    - by peppergrower
    I'm using nginx to serve three sites: example1.com (which redirects to www.example1.com), example2.com (which redirects to www.example2.com), and a subdomain of example2.com, call it sub.example2.com. This all works fine without SSL. I recently got SSL certs (from StartSSL), one for www.example1.com, one for www.example2.com, and one for sub.example2.com. I got them set up and everything seems to work (I'm using SNI to make all this work on a single IP address), except for sub.example2.com. I can still access it fine over non-SSL, but on SSL I just get a timeout. If I go directly to my server's IP address, I get served the SSL certificate for sub.example2.com, so I know nginx is loading the certificate properly...but somehow it doesn't seem to be listening for sub.example2.com on port 443, even though I told it to. I'm running nginx 1.4.2 on Debian 6 (squeeze); here's my config for sub.example2.com (the other domains have similar configs): server { server_name sub.example2.com; listen 80; listen 443 ssl; ssl_certificate /etc/nginx/ssl/sub.example2.com/server-unified.crt; ssl_certificate_key /etc/nginx/ssl/sub.example2.com/server.key; root /srv/www/sub.example2.com; } Does anything look amiss? What am I missing? I don't know if it matters, but StartSSL lists the base domain as a subject alternative name (SAN); not sure if that would somehow pose problems, if both subdomains list the same SAN.

    Read the article

  • cisco 2900xl - SNMP - Get mac address of device connected to an interface

    - by ankit
    Hello all, Basically what i want to do is to find out what is the mac address of a device plugged in to an interface on the switch (FastEthernet0/1 for example) reading through the switch documentaion i found out that i can configure snmp trap on it to make it notify of any new mac address the switch detects by using the command snmp-server enable traps mac-notifiction but for some reason my switch does not support this feature. the only options i see are CORE_SWITCH(config)#snmp-server enable traps ? c2900 Enable SNMP c2900 traps cluster Enable Cluster traps config Enable SNMP config traps entity Enable SNMP entity traps hsrp Enable SNMP HSRP traps snmp Enable SNMP traps vlan-membership Enable VLAN Membership traps vtp Enable SNMP VTP traps <cr> so the other way would be for me to run a cronjon on my gateway to poll the switch periodically using snmp to get new mac addresses i have looked everywhere but cant seem to find the OID that would provide me this information. any help i can get would me very much appreciated ! here's the output from "show version" on my switch Cisco Internetwork Operating System Software IOS (tm) C2900XL Software (C2900XL-C3H2S-M), Version 12.0(5.4)WC(1), MAINTENANCE INTERIM SOFTWARE Copyright (c) 1986-2001 by cisco Systems, Inc. Compiled Tue 10-Jul-01 11:52 by devgoyal Image text-base: 0x00003000, data-base: 0x00333CD8 ROM: Bootstrap program is C2900XL boot loader CORE_SWITCH uptime is 1 hour, 24 minutes System returned to ROM by power-on System image file is "flash:c2900XL-c3h2s-mz.120-5.4.WC.1.bin" cisco WS-C2912-XL (PowerPC403GA) processor (revision 0x11) with 8192K/1024K bytes of memory. Processor board ID FAB0409X1WS, with hardware revision 0x01 Last reset from power-on Processor is running Enterprise Edition Software Cluster command switch capable Cluster member switch capable 12 FastEthernet/IEEE 802.3 interface(s) 32K bytes of flash-simulated non-volatile configuration memory. Base ethernet MAC Address: 00:01:42:D0:67:00 Motherboard assembly number: 73-3397-08 Power supply part number: 34-0834-01 Motherboard serial number: FAB040843G4 Power supply serial number: DAB05030HR8 Model revision number: A0 Motherboard revision number: C0 Model number: WS-C2912-XL-EN System serial number: FAB0409X1WS Configuration register is 0xF thanks, -ankit

    Read the article

  • See former key sequences in vim

    - by Vasiliy Sharapov
    Sometimes I share screen shots and clips of vim usage with others. It would be nice to expand on the part of the status bar highlighted in this picture: I would like some way to make previous key sequences visible as well, such as: y2w jj f[ p 2d - You can see the key sequences leading up to the current one. I'll elaborate on my wish list at the bottom. Is something like this is available as a plugin or vim script? The sheer number of scripts available on vim online makes this hard to find by keyword. Some features I would hope for (but seem improbable): Delimit key sequences with a non-keyboard character instead of space, and a different one for the current command, so y2w jj f[ p 2d might become y2w¦jj¦f[¦p » 2d Replace keys that have a letter alternative with the alternative, such as the right arrow key - ^[[C with the equivalent l. Edit: To clarify, the right arrow key is a valid key in vim, but has no character to represent it, the l key preforms the same function and could/should substitute it. Have previous keystrokes run all the way to the beginning of the line (instead of just one or two), and just have vim's command prompt overwrite it when necessary. Replace some keystrokes with a more elegant alternative, for example hhhhh with 5h or more impressively d2f) with d% (in the appropriate situation).

    Read the article

  • PHP scripts randomly becoming really slow to respond - Database lockup?

    - by webnoob
    Hi All, I wasn't sure whether to post this here or on stackoverflow, so apologies if its in the wrong place. I have about 7 php scripts running on a centOS VPS. Each of these scripts contacts a game server and processes the logs, with the logs it either does some database queries or sends info back to the game server. I am having an issue where some of the scripts will randomly become REALLY slow to respond and I don't know where to start with my debugging. Each script connects to its own database schema but on the same MySQL server. Each script will do about 4 inserts per second and twice as many select statements on their respective databases. I thought a database lockup may cause the issue but some console messages that are read from the database are sent to the game servers console without issue every 30 seconds, even when the script is slow to responding to other commands. Non of the scripts are using a lot of memory or CPU power. About 0.1% each. I know this information is really vague but I don't know linux very well at all (in fact, top is about my limit) and I really don't know where to start debugging this. Thanks.

    Read the article

  • Keyboard's media keys are blocked by a program

    - by Mike Hanson
    I've got a Microsoft Natural Ergonomic Keyboard 4000. In addition to the regular keys, it's also got keys for Web/Home, Search, Mail, Favorites (5), Calculator, and Media functions (Mute, Volume Up/Down, and Play/Pause). Everything works most of the time, and the exception is rather odd. I use a programming system called Clarion. When that has focus, the Media keys don't work. (All the others still do.) I've also discovered that programs that I create using Clarion also block the media keys (only when they have focus). This indicates that it's probably something in Clarion's Run-Time Library (RTL) that's causing the trouble. The keys will work if I click on a non-Clarion window before hitting the media key, but that's an undesirable hassle. The odd thing is that I have many colleagues with the same keyboard, and they have no problem. When I recently upgraded from Vista Professional to Win7 Ultimate, I noticed that various things "appear" differently. For example, with my old system, when I changed the volume or muted the volume bar visualization always appeared at the bottom right on the screen. Now it doesn't appear in certain programs, even when it works. This indicates an order of precedence for visual elements. I'm fairly certain a similar order of precedence exists for keyboard hooks. Depending on how the hooks are defined, and the order in which they're applied, it would seem that sometimes the IntelliType drivers don't see the media keystrokes. The Media keys probably behave differently than the rest of the "special" keys, because they are more of a standard across all keyboards, so perhaps are handled by a different driver hooking mechanism. Does anyone have any suggestions of how I might fix this problem? Is there some way to change the order of hooks? Delay the loading of the IntelliType driver? Thanks in advance!

    Read the article

  • Task Manager Does Not Start Every Time

    - by diek
    I have had a problem that started some time ago, 6 months maybe. I should have noted the first instance but I didn't. I am using Windows 7 Pro, 32bit. Under normal circumstances I can open up the the Task Manager, via the task bar or cntrl alt del. When I get a program stuck, causing a freeze or non-responsive system I try to open the task manager. It will not work. I have had plenty of similar problems in the past and I had no trouble getting it open. I have searched the internet but the only results I can find are when the task manager will not start under any situation. I am running ESET NOD32 as the anti-virus. The latest example happened when I opened a new tab in Google and tried to copy an image. Google accounts for at least 50% of the examples. Ran System File Checker tool, sfc /scannow as recommended on another post. No errors returned. Any guidance would be appreciated.

    Read the article

  • WRTU54G-TM router with 3rd party firmware; Can custom firmware include stock binary portions?

    - by dlamblin
    I've been doing a lot of reading online about the Linksys WRTU54G-TM router model that I now own. It seems getting a custom firmware onto it is not a problem. But no one is talking about retaining the Voip features (yet). So far they're all disappointed that it's not a SIP machine and used GSM over IPSec. Personally I don't care about using it with non-t-mobile. If I take the original firmware, shouldn't I be able to extract it, and it's SquashFS image, and then move all of the t-mobile specific binaries for enabling the calling features over to a custom firmware installation (maybe OpenWRT)? You might ask why, and the reason is, that if I do this I could retain my calling features, which I do want, and ssh to the router and use it to run additional software, as any OpenWRT router could do. Does anyone know if this can be done, and how the firmware's binaries could be gotten at and installed correctly? Update I have found someone working on 3rd party WRTU54G-TM firmware. I am still interested in my second part of the questions, that is can't the stock firmware images be pulled apart and have the close-source, if any, binary kernel modules moved into another more flexible custom firmware?

    Read the article

  • Rebinding Keys on a Dell Keyboard

    - by Maarx
    I have a Dell Multimedia Keyboard, similar to this one: It has many non-standard keys, like the small circular ones across the top, and the "Multimedia" keys above INSERT/HOME/PAGE_UP. They can be rebound through simple registry entries. Some sample ones are included below: [HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion\Explorer\AppKey] [HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion\Explorer\AppKey\15] "ShellExecute"="C:\\Program Files (x86)\\Mozilla Firefox\\firefox.exe http://mail.google.com/mail/#inbox" [HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion\Explorer\AppKey\16] "Association"=".cda" [HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion\Explorer\AppKey\17] "ShellExecute"="C:\\Windows\\System32\\SnippingTool.exe" [HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion\Explorer\AppKey\18] "ShellExecute"="calc.exe" [HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion\Explorer\AppKey\7] "Association"="http" I've rebound the "MAIL" key to, instead of booting Outlook, to booting Firefox directed at my G-Mail account. I've rebound the button that would normally open "MY COMPUTER" to instead boot the Windows 7 "Snipping Tool", something I find very useful. Now, I'm looking to do some other things that I don't already know how to do. Note that answering this question doesn't necessarily require any knowledge about the keyboard or rebinding the keys: I can add, for any given key, a "ShellExecute" entry, and it will simply execute the following command as if it was typed at a Command Prompt. (I'm aware I dumbed that down rather significantly, but bear with me. I'm not really a Windows guy myself.) I use the volume knob for it's intended purpose, to change volume. I would like to change, however, a different key, to "reset" the Windows volume level back to exactly 50%, or, as it refers to it, "50", on it's 0-100 scale. I'm looking for the "program" (what I would type at a command prompt? these are still just Sys32 programs in the PATH, aren't they?) that, I imagine, would take arguments, to change Sound/Volume settings under Windows 7. Perhaps, for clarification, something that might take the form "C: SetVolume -slevel 50" or something.

    Read the article

  • Email test deferred (mail transport unavailable) with ClamAV

    - by dirt
    I'm trying to set up a simple new mail server; when I send a test email to the server the email is getting hung up during delivery (user mapping is found) and the email is never found in /home/user/Maildir/new Here is my maillog after a fresh reboot and test email, there are a few warnings I am unfamiliar with. Can you please point me in the right direction? Oct 25 14:54:57 loki dovecot: master: Dovecot v2.0.9 starting up (core dumps disabled) Oct 25 14:54:58 loki postfix/postfix-script[1369]: starting the Postfix mail system Oct 25 14:54:58 loki postfix/master[1370]: daemon started -- version 2.6.6, configuration /etc/postfix Oct 25 14:56:00 loki postfix/tlsmgr[1457]: warning: request to update table btree:/etc/postfix/smtpd_scache in non-postfix directory /etc/postfix Oct 25 14:56:00 loki postfix/tlsmgr[1457]: warning: redirecting the request to postfix-owned data_directory /var/lib/postfix Oct 25 14:56:00 loki postfix/smtpd[1455]: connect from mail-ob0-f180.google.com[209.85.214.180] Oct 25 14:56:01 loki postfix/smtpd[1455]: 1CF5E20A8B: client=mail-ob0-f180.google.com[209.85.214.180] Oct 25 14:56:01 loki postfix/cleanup[1461]: 1CF5E20A8B: message-id= Oct 25 14:56:01 loki postfix/qmgr[1379]: 1CF5E20A8B: from=, size=1788, nrcpt=1 (queue active) Oct 25 14:56:01 loki postfix/qmgr[1379]: warning: connect to transport private/scan: No such file or directory Oct 25 14:56:01 loki postfix/error[1462]: 1CF5E20A8B: to=, orig_to=, relay=none, delay=0.18, delays=0.15/0.02/0/0.01, dsn=4.3.0, status=deferred (mail transport unavailable) Oct 25 14:56:01 loki postfix/smtpd[1455]: disconnect from mail-ob0-f180.google.com[209.85.214.180] master.cf snippets: # ========================================================================== # service type private unpriv chroot wakeup maxproc command + args # (yes) (yes) (yes) (never) (100) # ========================================================================== smtp inet n - n - - smtpd submission inet n - n - - smtpd -o smtpd_tls_security_level=encrypt # -o smtpd_sasl_auth_enable=yes # -o smtpd_client_restrictions=permit_sasl_authenticated,reject # -o milter_macro_daemon_name=ORIGINATING smtps inet n - n - - smtpd -o smtpd_tls_wrappermode=yes # -o smtpd_sasl_auth_enable=yes # -o smtpd_client_restrictions=permit_sasl_authenticated,reject # -o milter_macro_daemon_name=ORIGINATING scan unix - - n - 16 smtp -o smtp_data_done_timeout=1200 -o smtp_send_xforward_command=yes -o disable_dns_lookups=yes 127.0.0.1:10026 inet n - n - 16 smtpd -o content_filter= -o local_recipient_maps= -o relay_recipient_maps= -o smtpd_restriction_classes= -o smtpd_client_restrictions= -o smtpd_helo_restrictions= -o smtpd_sender_restrictions= -o smtpd_recipient_restrictions=permit_mynetworks,reject -o mynetworks_style=host -o smtpd_authorized_xforward_hosts=127.0.0.0/8

    Read the article

  • NetApp NDMP backup with BE 2010 R2 works, restore fails

    - by uuwe
    Hi, I'm having some issues with a new Backup Exec 2010 R2 installation. I configured a NetApp FAS2020 as an NDMP device and want to backup files from the NAS to a tape drive connected to my backup server. I set up ndmpd according to this document (http://www.symantec.com/business/support/index?page=content&id=TECH48957) and created a separate backup user (http://filers.blogspot.com/2006/09/setting-veritas-netbackup-with-non.html). Backup works perfectly, but restoring any file gives me an authentication failed error. The NDMP device has a "global" ndmp user configured in the device tab (tried this with the newly created ndmpd backup user and the netapp root) and I can also configure separate resource credentials in the BE restore job. I have tried setting the same accounts for the "global" ndmp device and the restore credentials and have also tried setting different accounts for them. NDMP debug level is at 5 and this is what shows up in /etc/messages. The session is closed immediately after it has been granted. 16:12:07 PST [Java_Thread:info]: ndmpdserver: ndmpd.access allowed for version = 4, sessionId = 51, from src ip = 192.168.11.17, dst ip = FAS2020-1/192.168.11.75, src port = 50857, dst port = 10000 16:12:07 PST [Java_Thread:info]: Ndmpd51: ndmpd session closed successfully for version = 4, sessionId = 51, from src ip = 192.168.11.17, dst ip = FAS2020-1/192.168.11.75, src port = 50857, dst port = 10000 Running wireshark on the backup server doesn't produce much. It shows a SYN - SYN/ACK - NDMP CONNECT_CLOSE Request from the backup server. The Resource Credentials for the restore job behave very oddly. If I enter NDMP credentials and do "Test All" it fails. If I use my regular domain backup account, it is successful. There are no failed or succeeded logons in the NetApp ndmp log and tracing this check shows that it doesn't even connect to the NAS. This makes me think that this is more likely flaky BE behaviour rather than misconfiguration of the NAS. Here is the options ndmp output: FAS2020-1 options ndmp ndmpd.access all ndmpd.authtype challenge ndmpd.connectlog.enabled on ndmpd.enable on ndmpd.ignore_ctime.enabled off ndmpd.offset_map.enable on ndmpd.password_length 16 ndmpd.preferred_interface disable ndmpd.tcpnodelay.enable off

    Read the article

  • BGP path prepended route not listed anywhere

    - by Julien Vehent
    We have a simple multi-homed setup with two routers that advertise our AS to two ISP. The second ISP (ISP B) is only used for backup when ISP A goes down, so we prepended our AS 3 times on this route. I spend a couple of hours this morning poking at looking glass routers all over the internet, and none of them list our backup route with the prepended path. I checked the south african internet exchange, the london internet exchange, oregon internet exchange and a couple dozen ISPs. All of them have multiples routes through ISP A, often with 3 or 4 hops. The route through ISP B should, at least, appear somewhere and have 5 or 6 hops. But I couldn't find it anywhere. (I checked the full bgp tables on the looking glass routers, using show ip bgp 65000) My questions are: Is there a limit to the size of a route after which most routers will simply discard the route ? Is our backup route even going to work when ISP A goes down, if no router knows about it ? Our two routers are connected on iBGP. Would it be possible that the route through ISPB is not announced because the iBGP session prefers the route through ISPA ? This is what non-exist-map and advertise-map are supposed to do, but none of those are used in either routers.

    Read the article

  • Search inside of text files

    - by Matt
    So here is the situation. I currently run a mail server for my small non-profit company. My mail server (Merak Mail Server) keeps logs in .log files and mail as .tmp files. Essentially these are just text files that are kept on the server. Problem is that when I put text into the "Containing text" field on Windows Explorer, it always misses the files and tells me no results returned. Then when I search the files one by one (painful at best), I find the files I need. Do I not understand the search feature well enough, or maybe I have it indexing wrong. I really don't care what I need to use to search the files, even a third-party app is fine with me, I just want to type an email address into a box and search all of my log files or email files and find out which one I am looking for. It can be Windows Search or something else, as long as I can find a way to get the job done I will be happy. Pay solutions are fine as well. Thanks everyone in advance.

    Read the article

  • Which linux distributions offer seamless support for UEFI and an LVM root out of the box?

    - by Jannik Jochem
    My new ultrabook (an Asus UX32VD) requires UEFI in order to boot from the internal harddisk. I use an LVM partition which contains my root fs and dual-boot Windows 8. I somehow managed to get this working on Sabayon Linux, however the overall process was pretty painful, and system upgrades keep breaking my configuration because everything depends on a hand-configured kernel and a hand-crafted GRUB2 configuration. This causes a lot of hassle and distractions for me, so I am considering to switch to a different distribution. However, I cannot find any concrete resources that precisely document the state of UEFI support in the popular distributions. As an example, the length of the Ubuntu wiki page on UEFI suggests that installing on UEFI systems is a non-trivial process, and this AskUbuntu thread on encrypted LVM on UEFI systems suggests that LVM might also be a problem. I know that this question seems somewhat open-ended, so I'll formulate concrete questions: Are there any Linux distributions with an installer that supports installing to an LVM root in a UEFI boot setting where Windows 8 is dual-booted? Which distributions support UEFI without having to jump through hoops in order to bootstrap into a UEFI-booted system or requiring manual configuration of the boot manager?

    Read the article

  • How to connect to a computer that is in Sleep mode over the internet

    - by Gerhard Weiss
    How to connect to a computer that is in Sleep mode over the internet? I am using LogMeIn to connect to another computer offsite. I just installed Windows 7 RC on that system and found that the Sleep mode actually works. Currently LogMeIn does not connect when the system is in Sleep mode or Hibernate mode (that is what their error message displays when you try). Is there a way to get LogMeIn to connect to a system in Sleep mode? Is there other software that gives simliar LogMeIn functionallity (like RDP, etc.) that could be used on Windows 7 instead. I just use LMI for connecting and nothing else (no printing or file transfers). A Non-expensive options (such as free) would be better. I have seen web sites mentioning "Wake on LAN". Does anyone have some good links on how to set this up to be accessed over the internet? Edited: It looks like LogMeIn BETA might be the solution. https://beta.logmein.com/welcome/nextgen/ Has anyone tried this beta yet?

    Read the article

  • Will Parallel-port dongle work on USB-to-Parallel Adapter?

    - by Gary M. Mugford
    We have a niche program running on a Win2K laptop that uses a security dongle connected to a parallel port for authentication. The laptop is getting creaky and I spent a frustrating night last night shopping various websites for a new laptop that had a parallel port. Seems I'm about three years late [G]. The question I have, is, if I buy a new(ish) laptop and use a USB-to-Parallel Port adapter, will the security dongle work? I know I'm not being specific about the app, but it's one most people wouldn't have heard of anyways. I've been guessing the answer to my question is no, since the app won't know to send a request out to the non-existent port. But, if the process actually is that the dongle sends a message INTO the computer every now and then, then it might work. And, I'm not sure whether the dongle is only needed at program startup time or randomly. The dongle is a 'permanent' addition to the old laptop. This is all about the money. We can have a newly-updated version of the program (which won't add any features we need) for the princely sum of $2700. Or we can spend $500 on a refurbed laptop still running WinXP, add a 30 buck adapter and keep the same solid, stolid performance we've come to appreciate. But it all comes down to the dongle behaviour. Oh, and a dock won't work. The whole laptop issue is about moving about the various nooks and crannies of the building with laptop in hand. Thanks for any suggestions/guidance. GM

    Read the article

  • Virtual host config issues in osx 10.7 server app

    - by Benno
    I have two mac mini lion servers setup to run as production and staging machines. My sysadmin decided on these machines over the previous CentOS we had because it had an "interface" to be able to manage it, rather than just the terminal. To be honest, I prefer the terminal. My problem is, the mac osx 10.7 server.app seems to be having issues with the creation of virtual hosts in the 'Web' section. It seems VERY touchy. For example, I cannot create a http virtual host first. I have to create a https host first with a unique dns name 9e..g vuly6), then create the http host with a different dns name to the first (e.g. www), or it appears to override it the first one, even though one is ssl and one is non-ssl. Further, it seems to override perfectly good configurations at random. For example, the default sites directory is usually /Users/default/Sites/Customsites or something, but sometimes when I load the server.app it changes to /var/empty. Also, if I change or add extra virtual hosts after the first one or two, it starts to mess up and the first two virtual hosts start having issues. Has anyone had any experience with setting up virtual hosts via this app? Am I able to manually create these virtual hosts, without using the app, and without the app overriding my settings when I restart apache?

    Read the article

  • Will having 2 MX records pointing to different mail server types cause delivery issues?

    - by Lyken
    I've inherited a setup where the mail server is exchange 2010. For some reason, I'm not sure why there is 2 MX records setup. One being the exchange server which is the higher priority while the external (non-exchange) server is the secondary mx record. I don't believe this was done for redundancy reasons as the other mail server is not set to route mail back to the exchange server (it's just the webhosts email for their hosting) The client has been experiencing disappearing email, however after my investigations its not actually disappearing, but exchange is successfully receiving the mail and then passing it on to the external server. It isn't happening all the time, just with some email messages from some domains. My question: Is exchange passing the mail on because it can see the secondary MX record and is configured (somewhere) to send mail out? If so, how do I stop it? Is it as easy as just removing the second MX record pointing to the external mail server and exchange will stop passing mail on? I'm not exchange expert so I'm kinda stumped. Exchange MX tools are saying everything is setup and configured correctly from an external point of view.

    Read the article

  • Difference between "traceroute" and "traceroute -U"

    - by AndiDog
    The manpage of traceroute says that the "-U" parameter (UDP probing) is the default, but I'm getting different results every time. With "-U": traceroute -U www.univ-paris1.fr traceroute to www.univ-paris1.fr (193.55.96.121), 30 hops max, 60 byte packets [...] 13 rap-vl165-te3-2-jussieu-rtr-021.noc.renater.fr (193.51.181.101) 59.445 ms 56.924 ms 56.651 ms [...] 18 * paris1web.univ-paris1.fr (193.55.96.121) 23.797 ms 23.603 ms but the normal traceroute gives me another result (never reaches the final node) - it's either "!X" or just exits after the maximum of 30 hops: traceroute www.univ-paris1.fr traceroute to www.univ-paris1.fr (193.55.96.121), 30 hops max, 60 byte packets [...] 11 te1-1-paris1-rtr-021.noc.renater.fr (193.51.189.38) 28.147 ms 28.250 ms 28.538 ms [... non-responding nodes ...] 28 site-1.03-jussieu.rap.prd.fr (195.221.126.58) 85.941 ms !X * * Note: I tried this very often and always get the same results. The path in my local network is always the same. So what does the "-U" parameter actually change here? I'm especially interested what the reason for "!X" could be (communication administratively prohibited). EDIT: If that helps, paris-traceroute gives me the following for the last hop: 14 P(1, 6) site-1.03-jussieu.rap.prd.fr (195.221.126.58) 34.938 ms !5 !T2 which means that node discards the packet with TTL=2 and returns an unknown message (not "destination unreachable" or the like).

    Read the article

  • Adding License to VMware Server 2 via scripting command?

    - by andyt25
    Hi all, I recently discovered the vimsvc/license command in vmware-vim-cmd and was trying to use that to automatically add my license key to a fresh vmware installation. vmware-vim-cmd -H hostip -O portnumber vimsvc/license --source file '/path/to/plaintext-file-that-contains-my-license-key.txt' plaintext-file-that-contains-my-license-key.txt contains my key in XXXXX-XXXXX-XXXXX-XXXXX format, I've also tried it with an extra carriage return at the end. Adding the key that way doesn't work, however. I always get the following error message: [200] Reading local file: /path/to/plaintext-file-that-contains-my-license-key.txt [200] Size of file is 24 bytes. returned were XXXXX-XXXXX-XXXXX-XXXXX [200] Changing license source to: file:/path/to/plaintext-file-that-contains-my-license-key.txt [500] Caught unexpected exception Type: N5Vmomi5Fault17NotEnoughLicenses9ExceptionE what() =vmodl.fault.NotEnoughLicenses GetMsg() = There are not enough licenses installed to perform the operation. It's kinda silly to require a license to be able to add a license, don't you think? ;-) So how do I go about and add the key via script? I would like to avoid any interaction as I have the rest of the install fully scripted and non-interactive. Kind Regards, Stefan

    Read the article

  • Understanding Security Certificates (and thier pricing)

    - by John Robertson
    I work at a very small company so certificate costs need to be absolutely minimal. However for some applications we do Need to have our customers get that warm fuzzy not-using-a-self-signed certificate feeling. Since creating a "certificate authority" with makecert really just means creating a public/private key pair, it seems pretty clear that creating a public/private key pair FROM such a "certificate authority" really just means generating a second public/private key pair and signing both with the private key that belongs to the "certificate authority". Since the keys are signed anyone can verify they came from the certificate authority I created, or if verisign gave me the pair they sign it with one of their own private keys, and anyone can use verisigns corresponding public key to confirm verisign as the source of the keys. Given this I don't understand when I go to verisign or godaddy why they have rates only for yearly plans, when all I really want from them is a single public/private key pair signed with one of their private keys (so that anyone else can use their public keys to confirm that, yes, they gave me that public/private key pair and they confirmed I was who I said I was so you can trust my public/private key pair as belonging to a legitimate third party). Clearly I am misunderstanding something, what is it? Does verisign retire their public/private key pairs periodically so that my verisign signed key pair "expires" and I need new ones? Edit: I learned that the certificate has an internal expiration date and it also maintains an internal value stating whether it can be used to sign other certificates (i.e. sign other private/public key pairs stored as certificates). Can't I get a few (even one) non-signing certificate signed by someone like verisign that I can use for authentication/encryption without a yearly subscription?

    Read the article

  • Batch copy gives errors, xcopy works fine

    - by ndm13
    I am writing a general file backup program. It searches the drive for files matching a set of types and then writes them to a folder on the desktop. I wrote it using xcopy on Windows XP but upon learning that xcopy was deprecated in favor of robocopy in Vista and newer, still wanting to maintain compatibility I decided to switch to the non-deprecated copy. This is where the problems begin. I'm trying to fix the copy routine. I thought I had everything sorted out, but it doesn't copy anything. My output is zero files copied for every iteration. Original Code using xcopy: for /r %%a in (*.bmp *.dds *.gif *.jpg *.jpeg *.png *.psd *.pspimage *.tga *.thm *.tif *.tiff) do ( echo f | xcopy "%%a" "%HOMEDRIVE%%HOMEPATH%\Desktop\LDR\Images\Bitmap\%%~nxa" /q /y /g /c ) Revised (broken) Code using copy: for /r %%a in (*.bmp *.dds *.gif *.jpg *.jpeg *.png *.psd *.pspimage *.tga *.thm *.tif *.tiff) do ( copy "%%a" "%HOMEDRIVE%%HOMEPATH%\Desktop\LDR\Images\Bitmap\%%~nxa" /d /y /z ) Output: The system cannot find the path specified. 0 files copied. I know that it seems everyone uses either xcopy or robocopy but can anyone help with copy? Note: I'm using Batch to keep it very lightweight and command-line accessible.

    Read the article

  • Is this memory compatible with this motherboard???

    - by ClarkeyBoy
    Hi, I have a Foxconn P35AP-S as seen here. I need to get some more RAM since I only have 1 2GB stick. The current one is 1066MHz. I would like to get the memory situated here: www.scan.co.uk/Products/6GB-(3x2GB)-Corsair-XMS3-Classic-DDR3-PC3-10666-(1333)-Non-ECC-Unbuffered-CAS-7-7-7-20-165V memory. It is 6GB of Corair 1333MHz memory. According to the motherboard website it is able to take 1333MHz, but it says oc** next to it (which means achieved when overclocked). So my question is: are they still compatible without overclocking, or does the motherboard require overclocking to be compatible? If it requires overclocking (which I have no idea how to do) can anyone recommend any other memory (in the region of 6GB) which the motherboard is compatible with? I'd rather it were from Scan, but to be honest it doesnt need to be. Many thanks in advance. Regards, Richard Edit: I just realised that the motherboard has a maximum capacity of 4GB of RAM. Scrap the RAM given above, I'd like to go for something like that but only 4GB. Edit: Scrap that last edit - its only if I go for DDR3 that I need to take this into account. DDR2 is a maximum of 8GB.

    Read the article

  • Ho can I recover from SharePoint configuration errors after promoting the server to a Domain Controller?

    - by jjr2527
    I have a SharePoint 2010 VM setup in VirtualBox and I was using local machine accounts to handle security on the server. While preparing for a demo it came time to have some meaningful users on my VM image. I followed some docs on promoting my server to a Domain Controller in a new forrest. So now I have [MachineName].SPDEMO.CONTOSO.com and I can add users as needed. However, when I try to connect to my SharePoint sites I am getting a white screen with the error: "Cannot connect to the configuration database" I changed the pool identity account of each of my IIS app pools to the new Administrator account and started the services successfully but I can't get the SQL services to start up. When I try to start them I get the following error: Windows could not start the SQL Server (MSSQLSERVER) on Local Computer. For more information, review the System Event Log. If this is a non-Microsoft service, contact the service vendor, and refer to service-specific error code 17058. In the event log I see the following error: The SQL Server (MSSQLSERVER) service terminated with service-specific error %%17058. Can I recover from this or should I roll back or just uninstall the Domain Controller role. I'd like to keep the server as a standalone DC so I can do some user profile creation/management but I need the SharePoint bits to work as well.

    Read the article

< Previous Page | 344 345 346 347 348 349 350 351 352 353 354 355  | Next Page >