Search Results

Search found 11229 results on 450 pages for 'quirks mode'.

Page 353/450 | < Previous Page | 349 350 351 352 353 354 355 356 357 358 359 360  | Next Page >

• Should I use "Raid 5 + spare" or "Raid 6"?

  - by Trevor Boyd Smith

  What is "Raid 5 + Spare" (excerpt from User Manual, Sect 4.17.2, P.54): RAID5+Spare: RAID 5+Spare is a RAID 5 array in which one disk is used as spare to rebuild the system as soon as a disk fails (Fig. 79). At least four disks are required. If one physical disk fails, the data remains available because it is read from the parity blocks. Data from a failed disk is rebuilt onto the hot spare disk. When a failed disk is replaced, the replacement becomes the new hot spare. No data is lost in the case of a single disk failure, but if a second disk fails before the system can rebuild data to the hot spare, all data in the array will be lost. What is "Raid 6" (excerpt from User Manual, Sect 4.17.2, P.54): RAID6: In RAID 6, data is striped across all disks (minimum of four) and a two parity blocks for each data block (p and q in Fig. 80) is written on the same stripe. If one physical disk fails, the data from the failed disk can be rebuilt onto a replacement disk. This Raid mode can support up to two disk failures with no data loss. RAID 6 provides for faster rebuilding of data from a failed disk. Both "Raid 5 + spare" and "Raid 6" are SO similar ... I can't tell the difference. When would "Raid 5 + Spare" be optimal? And when would "Raid 6" be optimal"? The manual dumbs down the different raid with 5 star ratings. "Raid 5 + Spare" only gets 4 stars but "Raid 6" gets 5 stars. If I were to blindly trust the manual I would conclude that "Raid 6" is always better. Is "Raid 6" always better?

  Read the article

• How do I prevent Excel from locking files by default?

  - by Andrzej Doyle

  When I double-click on a CSV file on a network share, the file is opened in Microsoft Excel (which is what I want). However, Excel assumes that I'm going to modify the file, and that everyone else is too, and so puts a lock on it. In practice I very rarely actually want to modify these files, merely read from them. And if I have the file open in an Excel window in the background, it stops anyone else from opening the same file. I am aware that I can manually open a file as read-only from the File - Open dialog within Excel. However I almost always open files by double-clicking on them in Explorer (or Outlook, for attachments). Is it possible to change the file association so that the default handler for CSV files is "Excel in read-only mode"? Is there a command-line argument that I can use in the Open With... dialog to achieve this? Or more bluntly - when I am looking at a CSV file in Windows Explorer, is there an easier way to open it read-only than starting up Excel myself, selecting File - Open, choosing "read only" from the dropdown, manually navigating to the same folder in the hierarchy, and then opening the file? (I am happy to have to jump through hoops on the rare occasions that I want to modify and save a file.)

  Read the article

• VMWare ESXi 5 - Expanded RAID 5 array - cannot access datastore

  - by Dayton Brown

  I'm using VMWare ESXi 5 and had a 2 TB RAID 5 setup on an HP DL360 with a P400i RAID card. I added two more 1 TB drives and using the SmartStart ACU, added the drives and expanded the logical disk. Now after booting back to ESXi, the server boots, but lists no available persistent storage. I've rescanned multiple times to no avail: the Datastore doesn't show up. I booted to GParted and the 1.8TB partition shows up, but it shows as unknown. Anyone have any good ideas? EDIT: Final Solution So after much gnashing of teeth, it was fairly simple to solve. I purchased an eSata 2 TB external drive and a PCI eSata card for my server. I then used Clonezilla to image the current partitions to my new external drive. You have to check "don't check drive sizes" in advanced mode, otherwise it will yell at you for have a smaller drive. For some reason my PCI card wouldn't boot on my HP server, so I hooked the drive up to another desktop I had, booted to VMWare, and copied the vmdk's to another drive. I'm going to blow out the RAID config and then create 1.5TB logical drives.

  Read the article

• Wireless keeps shutting off in Windows 7

  - by Nathan Adams

  I have Windows 7 Ultimate 32bit installed on a Dell Latitude XT Tablet and for the life of me I can't figure out this really weird problem. The symptom is that the Wireless will disconnect from the AP and if I tell it to scan again, it says there are no APs in the area. I do have another wireless card in the laptop and if I disable the first one and enable the second, I am able to get onto the wireless however if I want to use the first card again I have to restart. I tried enabling/disabling the device, nothing will kick start the wireless again in the first card without a restart. I even tried different drivers. So, it seems it is random but it does occur more often when there is increased network activity (ie downloading a large file). The laptop doesn't seem to be overheating. I have tried the following: Under "Change Advanced Power Settings" for the current power profile, I set the "Wireless Adapter settings" to "Maximum Performance". Under device manger, I went to the card in question, and went to the advanced tab and set the "Power Saving mode" to "MAX_PSP" Both cards I have seem to exhibit the behavior after awhile. Both models of those cards are: Dell Wireless 1505 Draft 802.11n WLAN Mini-Card Gigabyte GN-WS30N 802.11n mini WLAN Card Has anyone have any ideas or ran into this before?

  Read the article

• STOP 0x7b booting from iSCSI

  - by Michael

  Hi, I've a Windows 2008 SBS running. It boots of iSCSI. That setup worked for months until yesterday. I intended to reboot and gained a: STOP 0x0000007b INACCESSIBLE_BOOT_DEVICE and no idea why. My setup hasn't changed. No new controller, no new or changed iSCSI targets, no new Network Card or IP address changes. I had all Windows Updates on it. Last known good: same STOP. Allow unsigned drivers: same STOP. Safe mode (all variants): same STOP. Mount target from a client: works. Filesystem check fine. I booted of the SBS DVD but in computer repair options my target doesn't appear. When i choose setup the target appears. So, how can i diagnose what's going wrong? Any helpful tools? Any hints? Thanks in advance Michael

  Read the article

• How do I share a complete XP disk so it can be seen from a Windows 7 system? (To move all files to a

  - by Ian Ringrose

  This should be easier! (both computers can see the internet etc so I know the network it’s self is working) I have a normal home network with a Windows XP machine on it and the new Windows 7 (64 bit) machine. So I can transfer the files to the new Windows 7 machine, I wish to share the complete disk (and all files) from the Windows XP machine and access them from the Windows 7 machine. Is there a step by step set of instructions for doing this anywhere? So fare I have: put both computers into the same workgroup put the windows 7 machine into work network mode so it can see the XP machine in the work group shared the XP disk as read only But when I try to access a lot of the folders on the XP disks, I am told I am not allowed to access them. (I was not asked for any passwords by the windows 7 machine when I accessed the XP machine. The XP machine just has its default account with no password set on it) The XP machine runs XP home and hence has "simple file shairing" turn on. So it seems that even if I create a admin account (with password) and connect with that account, it still comes in as "guest" on the XP machine. Chooseing to share the folder I want access to rather then the top of the disk drive seems to work, but is a pain as I need to share each user's folder with a different share name. If the new computer was not a laptop, I would just plug the hard disk from the old machine into it, but being a laptop I don't have that option.

  Read the article

• System and Router configuration for setting up a home firewall based on Zentyal

  - by Ako

  I am not much of a system administrator, so please be patient if this looks too simple for you. I have a several computers at home, and all of them connect using an ADSL modem/router (and Wireless AP). I have been attacked several times (mainly from Russia and Ukraine), so I thought I should have some kind of firewall, besides the ESET firewall on my Windows 7. So now I have these (new) configuration: I have a small ADSL modem (Zyxel brand) which has only one Ethernet port. This modem is used to connect to internet and is configured in NAT mode. The interface has is configured with IP address 192.168.1.1. I have an old PC and I have installed zentyal on it. It has two Ethernet ports, eth0 and eth1. Eth0 is connected to the Zyxel modem with IP 192.168.1.2 and is checked as the WAN interface (external). I have another ADSL modem which is also a router with 4 Ethernet ports and Wireless AP. One of the Ethernet ports is connected to eth1 on Zentyal box. The Ethernet port's IP is 192.168.2.1 and Zentyal's eth1 is 192.168.2.2. Now, I want to enable other computers to connect to internet through the router both using Wireless and Ethernet. The problem is that I don't know how to configure the router so it routes connections to the Zentyal box. Does anyone have any clue? Again I am sorry if this looks stupid. Thanks.

  Read the article

• Wired to wireless bridge in Linux

  - by adrianmcmenamin

  I am attempting to set up my Raspberry Pi as a bridge (but I think this is not a question specific to the hardware) - using Debian wheezy. I have a hostapd.conf: (some details changed for security)... interface=wlan0 bridge=br0 driver=nl80211 auth_algs=1 macaddr_acl=0 ignore_broadcast_ssid=0 logger_syslog=-1 logger_syslog_level=0 hw_mode=g ssid=MY_SSID channel=11 wep_default_key=0 wep_key0=MY_KEY wpa=0 (yes, I know WEP is no good) And this in /etc/network/interfaces auto lo iface lo inet loopback iface eth0 inet dhcp allow-hotplug wlan0 iface wlan0 inet manual wpa-roam /etc/wpa_supplicant/wpa_supplicant.conf iface default inet dhcp auto br0 iface br0 inet dhcp bridge-ports eth0 wlan0 Everything seems to come up ok, but I cannot associate with the bridged wireless connection - even though the flashing lights on the USB stick suggest packets are being exchanged. I have read somewhere that not all cards/devices will run in hostap mode - they won't pass packets in one direction: is that right? (The info was a bit old)- this my card: [ 3.663245] usb 1-1.3.1: new high-speed USB device number 5 using dwc_otg [ 3.794187] usb 1-1.3.1: New USB device found, idVendor=0cf3, idProduct=9271 [ 3.804321] usb 1-1.3.1: New USB device strings: Mfr=16, Product=32, SerialNumber=48 [ 3.816994] usb 1-1.3.1: Product: USB2.0 WLAN [ 3.823790] usb 1-1.3.1: Manufacturer: ATHEROS [ 3.830645] usb 1-1.3.1: SerialNumber: 12345 So, what have I got wrong here?

  Read the article

• mkvmerge: How to merge two videos, one without audio?

  - by ProGNOMmers

  I have two videos, one without audio (the second). Trying to merge them I have this error: mkvmerge concat1.webm +concat2.webm -o output.webm mkvmerge v5.8.0 ('No Sleep / Pillow') built on Oct 19 2012 13:07:37 Automatically enabling WebM compliance mode due to output file name extension. 'concat1.webm': Using the demultiplexer for the format 'Matroska'. concat2.webm': Using the demultiplexer for the format 'Matroska'. 'concat1.webm' track 0: Using the output module for the format 'VP8'. concat2.webm' track 0: Using the output module for the format 'VP8'. concat2.webm' track 1: Using the output module for the format 'Vorbis'. No append mapping was given for the file no. 1 (concat2.webm'). A default mapping of 1:0:0:0,1:1:0:1 will be used instead. Please keep that in mind if mkvmerge aborts with an error message regarding invalid '--append-to' options. Error: The file no. 0 ('concat1.webm') does not contain a track with the ID 1, or that track is not to be copied. Therefore no track can be appended to it. The argument for '--append-to' was invalid. Is there a way to say to mkvmerge to make the audio track longer? Thank you!

  Read the article

• Hard crash when using bluetooth headset on MacBook Pro and Lion 10.7.2

  - by jtalarico

  I recently picked up a bluetooth headset (Motorola S10-HD) and started using it with my MacBook Pro (17" purchased new in 2010) running Lion 10.7.2. Here's what works - stereo audio: iTunes Spotify Pandora (via browser) games (e.g. Minecraft, which is a Java app) audio from YouTube Plex, VLC, other video players Here's what doesn't work well - stereo audio fails and the headset seems to go into mono (i.e. tinny-as-hell) mode: Google Hangout Skype GoTo Meeting Here's what's just downright catastrophic. If I'm listening to stereo audio and then decide to jump into a Skype call (Google Hangout, or GoTo Meeting), bluetooth often crashes and I can only get things working again by shutting down the device, disabling bluetooth, and getting things back up and running again. But the audio is still horrible, and MUCH better using just a simple set of iPhone earbuds and mic. About 80% of the time during such a call, bluetooth crashes. And about 90% of the time, after the call ends, Skype is shut down, or I try to switch back to playing stereo audio, I get a hard crash!! The gray screen of death descends and I'm told I need to restart my machine. In one such instance, even after a reboot, I could not enable bluetooth again ("Turn Bluetooth On" was grayed out in taskbar). Is this just a weak implementation of bluetooth by Apple, or is this a hardware issue? I've seen others posting similar issues even on the Apple support site indicating that bluetooth headsets are failing left and right, but I haven't seen anyone mention hard crashes.

  Read the article

• Multiple Remote Desktop Connection in Windows Server 2003?

  - by Joel Bradley

  My company is transitioning all user PC's to Windows 7 64-Bit in anticipation of the 2014 cutoff for Windows XP support. So far everything has been going great except for one specific piece of software that will not run in Windows 7. The current plan is to give everyone a cheap secondary PC to run this software but I feel that's a little much for software that's not even used all the time, although it is essential. I've suggested we install virtual machines but the company does not want to pay for the XP licences. I have access to a copy of Windows Server 2003 that is no longer being used and I was wondering if it was possible to create a remote desktop server. I know it can be done on a one-to-one basis, but this is a 15 person helpdesk. I'd like to be able to support multiple remote dekstop sessions, each with their own logins and dekstops. Is this possible? Are there any other alternatives to my issue? FYI, I've been told that XP mode is only free for consumers. There are costs when used in a corporate environment.

  Read the article

• Syntax error at '{'; expected '}' when using nagios in puppet

  - by jiangchengwu

  It's a big problem to me, because I'm not familiar with puppet. ERROR on the puppetmaster: debug: importing '/etc/puppet/manifests/nodes/group-1.pp' err: Could not parse for environment production: Syntax error at '{'; expected '}' at /etc/puppet/manifests/nodes/group-1.pp:6 ERROR on the puppet client: err: Could not retrieve catalog from remote server: Error 400 on SERVER: Could not parse for environment production: Syntax error at '{'; expected '}' at /etc/puppet/manifests/nodes/group-1.pp:6 in group-1.pp: node 'group1' { include ntp class { 'nagios::host': #this is line 6 nodename => $clientcert, appname => 'test', } } nagios::host in module module/nagios/host.pp code are here: class nagios::host($nodename, $hostgroup) { file { '/usr/lib/nagios/plugins': mode = "755", require = Package["nagios-plugins"], } ... @@nagios_service { "${nodename}_check_ssh": ensure => present, use => 'generic-service', host_name => "${nodename}", notification_interval => 60, flap_detection_enabled => 0, service_description => "SSH", check_command => "check_ssh", target => "/etc/nagios3/services.d/${nodename}.cfg", } } and the file module/nagios/init.pp is blank How could I fix it ?

  Read the article

• External HDD incorrectly detected as internal - how change to enable hot swap/eject?

  - by Sam

  Hi All, I have win 7 x64 Home Prem. The HDD is a seagate barracuda, 7200.7 ST3120827AS. 3.5", Serial: 3ms006n6, Firmware: 3.42 (no further updates) NexStar CX External case (drivers installed). I have three drives: WD320 with OS installed WD750 data storage (internal) seagate 120 (external) - connected via esata board connected to sata on motherboard (MSI p43 neo) Tried uninstalling HDD in device manager to no effect. Also the internal WD750 is detected as an external drive and win taskbar icon allows for it to be ejected (unlike the seagate). All drives are configured - Online, Simple, Basic, NTFS, Active, Primary Partition (except c drive). The seagate was previously used as a primary disk with XP operating system so I deleted the volume and created/reformatted (not quick). HDD is no longer "Active". But did not fix problem. Background Originally, I installed win 7 with the bios set to IDE and forgot to install the chipset drivers. Then I changed win 7 to install the AHCI drivers, changed the bios to AHCI and rebooted. Win 7 loaded drivers but WD HDD gave problems/crashed. I installed chipset drivers and latest intell storage matrix software thingie (in safe mode). Everything worked fine after that except for the problem of not corrrectly detecting the external drive] I have noticed that under the driver properties (and similarly in the registry) the two drives are configured differently (e.g. in driver details property capabilities for the WD the value is set to 0000006, CM_DEVCAP_REMOVABLE & EJECTSUPPORTED - whereas the seagate shows 0000080 & CM_DEVCAP_SURPRISEREMOVALOK). Any easy way to configure things? I tried physically swapping the sata connections on the mainboard without success So far I have found that a solution to my problem might be to perform some reg changes: http://superuser.com/questions/12955/how-do-i-remove-the-option-to-eject-sata-drives-from-the-windows-7-tray-icon

  Read the article

• USB seems to pause system

  - by Marco van de Voort

  I've an application that does some simple measuring, for which it polls a few 100kbs several times a second (8-25 times) The behaviour is not really dependant on chipset (happens on several mobo's intel 965- P55) and OSes (XPsp3 and win7). Also the make of the USB keyboard doesn't seem to matter. I notice that sometimes when an USB kbd is plugged in, the system pauses for say 500-1000ms. (about 900-1000ms on disconnect, and 400-500 on the subsequent connect) It also happens for other USB devices (most notably mice and massstorage devices), but only the first time such device is connected to an installation. This disrupts the measurement and I really would like to get rid on this. I already tried to disable as much as possible. (powersave, teletubby mode (*) etc), and while this helped with the non-USB related disruptions of the measurement, it doesn't help with the USB related ones. (*) fyi, turning off themes (to resp. classic/non-aero), and turning off effects in system solved problems that occured when minimizing/maximizing the app. Any pointers to look into? I'm a bit stuck with this.

  Read the article

• Windows shutting down, CPU maxing out in Windows-7 32-bit? [closed]

  - by Vivek Sharma

  I have no idea, what is happening to my laptop. For last 5-6 times it has automatically shutdown while running, without doing anything serious. And I even do get the message during boot which says - Start windows normal - Start in safe mode It just boots up normal. Few days ago, my screen blinked and it the PC shutdown immediately. After that I was not able to get it started. I got it repaired, the guy said he has replaced the display chip (nVidia-nvs-140), but i seriously doubt that. Now it started working, but would shutdown every 20 mins or so. I have a dual boot, ubuntu-11.10 works just fine. Virus scan on windows shows nothing. I am pasting my perfmon output. My CPU for reason is maxing out to 100% continously, for windows internal processes. Please have a look at the attached file. Strangly now for last 2 hours it is working fine, but i am just writing emails and reading excels. ThinkPad T61 | t9300 | 3gb | nVidia 140 nvs-quadro (latest driver 296.10) What do you suggest?

  Read the article

• Changing the default boot option without losing the boot menu

  - by hvd

  I've had a working multi-boot setup with the Windows boot loader, containing menu items for two Windows 7 systems, and one for Grub. Grub in turn contains multiple menu items, but I think that's not relevant here. I've upgraded one system to Windows 8. When I now set a different system as the default, I lose the boot menu, and I lose the possibility of booting into the other systems. I've set Windows 7 as the default, rebooted, and get Windows 7, but I don't get to choose which system to boot into. I can run its own bcdedit to change the default back to Windows 8, and another reboot shows the boot menu again, but how can I avoid defaulting to Windows 8? Here are my current boot settings, is there anything that is misconfigured? C:\WINDOWS\system32>bcdedit Windows Boot Manager -------------------- identifier {bootmgr} device partition=F: description Windows Boot Manager locale nl-NL inherit {globalsettings} integrityservices Enable default {current} resumeobject {2f8b77f0-a30b-11e1-a9c6-a4bd8d37f662} displayorder {current} {2f8b77e3-a30b-11e1-a9c6-a4bd8d37f662} {2f8b77ee-a30b-11e1-a9c6-a4bd8d37f662} toolsdisplayorder {memdiag} timeout 30 Windows Boot Loader ------------------- identifier {current} device partition=C: path \WINDOWS\system32\winload.exe description Windows 8 locale nl-NL inherit {bootloadersettings} integrityservices Enable recoveryenabled No allowedinmemorysettings 0x15000075 osdevice partition=C: systemroot \WINDOWS resumeobject {2f8b77f0-a30b-11e1-a9c6-a4bd8d37f662} nx OptIn bootmenupolicy Standard Windows Boot Loader ------------------- identifier {2f8b77e3-a30b-11e1-a9c6-a4bd8d37f662} device partition=D: path \Windows\system32\winload.exe description Windows 7 locale nl-NL osdevice partition=D: systemroot \Windows resumeobject {59616f59-a2ba-11e1-b73a-806e6f6e6963} nx OptIn pae Default bootmenupolicy Standard hypervisorlaunchtype Auto detecthal Yes sos No debug No Real-mode Boot Sector --------------------- identifier {2f8b77ee-a30b-11e1-a9c6-a4bd8d37f662} device partition=C: path \grub\winloader\grub.boot description Grub 2

  Read the article

• When ran as a scheduled task, cannot save an Excel workbook when using Excel.Application COM object in PowerShell

  - by Daniel Richnak

  I'm having an issue where I've automated creating an Excel.Application COM object, add some data into a workbook, and then saving the document as an xlsx. This works fine if: I'm already in Powershell interactive host and either run each command in sequence, or execute as a ps1. I run it from cmd.exe, using the syntax: powershell.exe -command "c:\path\to\powershellscript.ps1" I create a scheduled task in Windows 7 / Server 2008 R2, use the above powershell.exe -command syntax, and use the mode "Run only when the user is logged on". It fails when I modify the same scheduled task, but set it to "run whether the user is logged on or not". Here's a sample script that illustrates the problem I'm having: $Excel = New-Object -Com Excel.Application $Excelworkbook = $Excel.Workbooks.Add() $excelworkbook.saveas("C:\temp\test.xlsx") $excelworkbook.close() I have a theory that the COM object fails somehow if my profile isn't loaded / if it's not performed in a command window. Any ideas on which options to choose when creating the scheduled task, or which options to use when creating the Excel object or using the SaveAs() function? Can anybody reproduce this? I've been able to see this behavior on both a Server 2008 R2 machine, and Windows 7. Haven't tried other platforms.

  Read the article

• Nginx proxy to IIS Connection Timeout

  - by MitMaro

  I am having an issue with random timeouts with a Nginx proxy connecting to an IIS machine. I have been watching a packet capture between the two servers and it seems that the IIS machine is receiving a SYN packet but is not responding with what I think should be an ACK response. Before the timeout occurs there seems to be a slower response from the IIS server. There is no unusual memory or processor usage on the IIS or Nginx machine. Some information on the servers and setup: Nginx Machine: Ubuntu 10.04 64bit Nginx 0.7.65 Amazon EC2 Windows Machine: Windows Server 2008 IIS 7 ASP.net Application in Integrated Mode Nginx Error: 2011/01/10 17:57:40 [error] 8297#0: *30 connect() failed (110: Connection timed out) while connecting to upstream, client: 209.***.***.***, server: secure.example.com, request: "GET /a/path/deliver.aspx HTTP/1.1", upstream: "http://***.***.***.****:****//another/path/deliver.aspx", host: "secure.example.com" WireShark Packets 6521.449528 10.***.***.*** -> 174.***.***.*** TCP 38695 > us-cli [SYN] Seq=0 Win=5840 Len=0 MSS=1460 TSV=477422103 TSER=0 WS=7 6524.443239 10.***.***.*** -> 174.***.***.*** TCP 38695 > us-cli [SYN] Seq=0 Win=5840 Len=0 MSS=1460 TSV=477422403 TSER=0 WS=7 6530.443241 10.***.***.*** -> 174.***.***.*** TCP 38695 > us-cli [SYN] Seq=0 Win=5840 Len=0 MSS=1460 TSV=477423003 TSER=0 WS=7

  Read the article

• How can I create a simple Exchange 2010 backup solution?

  - by bduncanj

  I'm sure this question's been asked a dozen times in one form or another, however after much searching, there doesn't appear to be an obvious simple recovery solution for a single Exchange box. We're using Exchange 2010 on a single server, the server hosts the AD and nothing else on the network uses the AD. The intent is to run this server as you would an externally hosted Exchange server - access only via HTTP (RPC mode or OWA) - all other ports blocked. I've a daily backup running, using Windows Server 2008 volume shadow service to backup the Exchange data to an external hard disk. My question is, how do I perform a bare metal recovery of this server? 1) Do I need to be explicitly including the active directory information in this nightly backup, or will it be there by virtue of the fact that this system is the primary AD server and the Windows backup service knows this? 2) I understand I can re-install Server 2008 onto my new hardware (in the case of hardware failure) and then run Exchange 2010 setup.exe with a /recover argument, referencing the backup volume. 3) It is acceptable to have some downtime during this recovery process. But is there anything else I should be aware of? Thanks! Duncan

  Read the article

• break Folder Protection, Folder Guard Lock or Folder in Windows XP?

  - by SonyAdi

  when I'm making a new partition by the partition magic. Then all of a sudden power failure. Unfortunately because my computer is not equipped with UPS (Power supply Uniterruptible), my computer finally died, too. When power is restored, I tried to turn on the computer. Suddenly my computer can not boot normally into windows. Option through safemode and others all I've tried. The result fails, can not boot at all, into safe mode also can not. And I know the cause. Partition Magic did not finish the work and stopped in the middle of the road and cause the transfer of data files or stopped, finally file2 any default windows were destroyed as well. Unfortunately my important data I store in my document. Finally, I take my hard drive to a friend. Hopes to open a computer hard drive through friend, at least I could save my important data, and then I can install window again by reformatting my hard drive is first. I read the hard drive in explorer my friend, complete with their data, but the data of my important data in my document can not get to go because it requires administrator privileges or the original user's default start my windows (my computer) to open my document folder tersebut.Ini actually very similar to the work or Folder Protection Folder Guard. result I was disappointed and almost desperate to get back my important data is. how do i break Folder Protection, Folder Guard Lock or Folder in Windows XP?

  Read the article

• SQL Server Subscriber Migration

  - by SuperCoolMoss

  We're currently have one way transaction replication from a SQL Server 2005 OLTP publisher/distrbituor to two subscribers (one SQL 2005 and the other SQL2008 R2). Replication security is via the SQL Agents' domain service account (the same account is used on all boxes). The SQL2008R2 subscriber is used for BI purposes and hosts a database that has a subset of the Production publisher database tables, with different security and indexes. We need to migrate this BI subscriber to a newer box with more performant hardware. The plan is as follows: Stop replicating to the BI box (continue replicating to the other subscriber). Backup all databases on the BI box (including system databases). Restore all databases (including master in single user mode) to the new BI box (this has SQL Server 2008R2 already installed). Take the old BI box off the network and shut it down. Rename and Re-IP the new BI box to be the same as the old box. Switch replication back on. Are there any flaws in this approach?

  Read the article

• how to remove background layer of djvu file

  - by Jon

  Hello, I've downloaded some files from the Internet Archive. They come in different file formats and most of the time I use pdf. However, sometimes the scans are saves in colour instead of b/w. This makes it difficult/impossible to read on a dedicated ebook reader. In that case I downloaded the djvu files as on the PC you can select which layer (color, bw,fore,back) one would like to see. Selecting the bw gives excellent results. However, the ebook reader does not has this option. The question is, how can I remove /extract a layer from the djvu file and save only this layer. So far I've tried the following two approaches: 1) select bw in the djvu viewer on the PC and printed to postscript file. Followed by a ps2pdf conversion. This works, but generates a fairly large pdf file. Sure, I can again upload it to any2djvu but it just seems to much manual work for each file. 2) I tried the shared annotation feature and said (mode bw). This works on the PC as desired but is ignored on the ebook reader as the other layers are still present. Any help or suggestions would be greatly appreciated.

  Read the article

• Are these three brand new sticks of RAM really dead?

  - by David Brown

  I'm working on a Dell Dimension 4700 desktop for a friend. It came with 512MB of DDR2 RAM (two sticks of 256MB). One morning, it started blue screening on startup with no helpful error messages. It refused to boot into any form of Windows installation, including Safe Mode, original recovery disk, and my custom Windows PE disk. It did boot into the Ultimate Boot CD, so I ran memtest86, which reported errors everywhere. I removed one stick of RAM and the system booted up just fine. I moved the remaining stick into each slot and the system continued to operate normally, so I came to the conclusion that the stick that I removed was dead. I ordered an exact replacement, along with 2 more sticks of 256MB DDR2 (again, exactly the same as the original), bringing the total system memory to 1GB. Upon installing the three brand new sticks, the system blue screened again, this time stating that win32k.sys attempted to write to read-only memory. I inserted my custom Windows PE disk in order to get a better look at the memory dump with BlueScreenView, but it refused to boot and produced another blue screen, but without an error message. I removed each new stick one-by-one, restarting each time. It continued to blue screen until I was left with only the original stick. I then tried inserting the new sticks in various different orders, but this only produced more blue screens. I reinserted all three sticks (along with the original) and ran memtest86 again, which reported errors all over the place. So, now I'm right back where I started. I don't think it could be the slots themselves, because I can plug the original stick into any slot and it works just fine. System setup reports each stick correctly and shows the total as 1GB, however. It just seems strange to me that all three brand new sticks of RAM could be dead on arrival. Is there something I missed? Or should I just go ahead and RMA them?

  Read the article

• Setting Remote Desktop to allows IPv6 connections

  - by Garrett

  Setup: Basically I have 3 machines (2 virtual and 1 physical) that I would like to be able to RDP in to from outside my NAT (a router). The VMs are Windows 7 and Windows XP, both fully patched with Teredo installed and working, both running in VirtualBox (their host also has Teredo working, though I'm not sure if that matters). They both have bridged network adapters with promiscuous mode enabled. The physical machine is Windows 7 fully patched with an HFS server running on it and a dynamic DNS set up for my public IPv4 address and port forwarded. It also has Teredo installed and working. Symptoms: According to http://test-ipv6.com/ all 3 have public IPv6 addresses, and they can all connect to http://ipv6.google.com/. I can ping the XP VM from the host it's running on but I cannot ping it from any other machine. Also, I cannot ping either of the other machines from anywhere. I cannot connect to any of them over RDP from IPv6, however I can connect to all of them through IPv4. Any ideas what is going wrong?

  Read the article

• Problem mirroring two monitors with different resolution

  - by quad

  Hello I am trying to put two monitors in mirror mode (Windows 7 Professional) with Ultramon 3.1.0. The two monitors: Main monitor: 24" Asus. 1680x1050 resolution (16/10). Secondary monitor: 19" LG. 1280x1024 resolution. The graphic card is a Nvidia GeForce 8600 GT. I have installed the Ultramon 3.1.0 and I have created a mirror, with the "stretch mirror image to fill monitor" and the "disable video overlays and 3D acceleration". When I start the mirroring, there are two zones in the lateral edges that are not displayed in the second monitor. I think this is because the width of the main monitor is 1680 px. and the width of the secondary monitor is 1280 px., but I have indicated "stretch mirror image to fill monitor" in the options. The same occurs in the top and the bottom edges, but the diference is minimal (1050 vs 1024 pixels). I want the same image (distortioned in the secondary monitor if is neccesary), but I don't know what is failing. Someone can help me, please? I have read Mirrored monitors of different resolution. Cloned screen on monitors with different resolutions

  Read the article

< Previous Page | 349 350 351 352 353 354 355 356 357 358 359 360  | Next Page >