Search Results

Search found 45752 results on 1831 pages for 'ubuntu linux'.

Page 358/1831 | < Previous Page | 354 355 356 357 358 359 360 361 362 363 364 365  | Next Page >

• Is there a test to see if hardware virtualization (vmx / xvm) are presently enabled within a Linux session?

  - by Dr. Edward Morbius

  I'm writing procedures for configuring VirtualBox support for 64-bit SMP guests, which requires hardware virtualization suppot (VTx/Intel, AMD-V/AMD). I have successfully configured this myself, however I'd like the procedure to be clear. sed -ne '/^flags/s/^.*: //p' /proc/cpuinfo | egrep -q '(vmx|svm)' && echo Has hardware virt || echo No HW virt ... shows if the CPU is capable. I've still got to go enable the feature in BIOS. Any way to test from within Linux to see that this is no or not? Thanks.

  Read the article

• Possible to get SSD TRIM (discard) working on ext4 + LVM + software RAID in Linux?

  - by Don MacAskill

  We use RAID1+0 with md on Linux (currently 2.6.37) to create an md device, then use LVM to provide volume management on top of the device, and then use ext4 as our filesystem on the LVM volume groups. With SSDs as the drives, we'd like to see the TRIM commands propagate through the layers (ext4 - LVM - md - SSD) to the devices. It looks like recent 2.6.3x kernels have had a lot of new SSD-related TRIM support added, including lots more coverage of Device Mapper scenarios, but we still can't seem to get it to cascade down properly. Is this possible yet? If so, how? If not, is any progress being made?

  Read the article

• How do I make Linux recognize a new SATA /dev/sda drive I hot swapped in without rebooting?

  - by Philip Durbin

  Hot swapping out a failed SATA /dev/sda drive worked fine, but when I went to swap in a new drive, it wasn't recognized: [root@fs-2 ~]# tail -18 /var/log/messages May 5 16:54:35 fs-2 kernel: ata1: exception Emask 0x10 SAct 0x0 SErr 0x50000 action 0xe frozen May 5 16:54:35 fs-2 kernel: ata1: SError: { PHYRdyChg CommWake } May 5 16:54:40 fs-2 kernel: ata1: link is slow to respond, please be patient (ready=0) May 5 16:54:45 fs-2 kernel: ata1: device not ready (errno=-16), forcing hardreset May 5 16:54:45 fs-2 kernel: ata1: soft resetting link May 5 16:54:50 fs-2 kernel: ata1: link is slow to respond, please be patient (ready=0) May 5 16:54:55 fs-2 kernel: ata1: SRST failed (errno=-16) May 5 16:54:55 fs-2 kernel: ata1: soft resetting link May 5 16:55:00 fs-2 kernel: ata1: link is slow to respond, please be patient (ready=0) May 5 16:55:05 fs-2 kernel: ata1: SRST failed (errno=-16) May 5 16:55:05 fs-2 kernel: ata1: soft resetting link May 5 16:55:10 fs-2 kernel: ata1: link is slow to respond, please be patient (ready=0) May 5 16:55:40 fs-2 kernel: ata1: SRST failed (errno=-16) May 5 16:55:40 fs-2 kernel: ata1: limiting SATA link speed to 1.5 Gbps May 5 16:55:40 fs-2 kernel: ata1: soft resetting link May 5 16:55:45 fs-2 kernel: ata1: SRST failed (errno=-16) May 5 16:55:45 fs-2 kernel: ata1: reset failed, giving up May 5 16:55:45 fs-2 kernel: ata1: EH complete I tried a couple things to make the server find the new /dev/sda, such as rescan-scsi-bus.sh but they didn't work: [root@fs-2 ~]# echo "---" > /sys/class/scsi_host/host0/scan -bash: echo: write error: Invalid argument [root@fs-2 ~]# [root@fs-2 ~]# /root/rescan-scsi-bus.sh -l [snip] 0 new device(s) found. 0 device(s) removed. [root@fs-2 ~]# [root@fs-2 ~]# ls /dev/sda ls: /dev/sda: No such file or directory I ended up rebooting the server. /dev/sda was recognized, I fixed the software RAID, and everything is fine now. But for next time, how can I make Linux recognize a new SATA drive I have hot swapped in without rebooting? The operating system in question is RHEL5.3: [root@fs-2 ~]# cat /etc/redhat-release Red Hat Enterprise Linux Server release 5.3 (Tikanga) The hard drive is a Seagate Barracuda ES.2 SATA 3.0-Gb/s 500-GB, model ST3500320NS. Here is the lscpi output: [root@fs-2 ~]# lspci 00:00.0 RAM memory: nVidia Corporation MCP55 Memory Controller (rev a2) 00:01.0 ISA bridge: nVidia Corporation MCP55 LPC Bridge (rev a3) 00:01.1 SMBus: nVidia Corporation MCP55 SMBus (rev a3) 00:02.0 USB Controller: nVidia Corporation MCP55 USB Controller (rev a1) 00:02.1 USB Controller: nVidia Corporation MCP55 USB Controller (rev a2) 00:04.0 IDE interface: nVidia Corporation MCP55 IDE (rev a1) 00:05.0 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) 00:05.1 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) 00:05.2 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) 00:06.0 PCI bridge: nVidia Corporation MCP55 PCI bridge (rev a2) 00:08.0 Bridge: nVidia Corporation MCP55 Ethernet (rev a3) 00:09.0 Bridge: nVidia Corporation MCP55 Ethernet (rev a3) 00:0a.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0b.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0c.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0d.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0e.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0f.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 00:19.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:19.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:19.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:19.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 03:00.0 VGA compatible controller: Matrox Graphics, Inc. MGA G200e [Pilot] ServerEngines (SEP1) (rev 02) 04:00.0 PCI bridge: NEC Corporation uPD720400 PCI Express - PCI/PCI-X Bridge (rev 06) 04:00.1 PCI bridge: NEC Corporation uPD720400 PCI Express - PCI/PCI-X Bridge (rev 06) Update: In perhaps a dozen cases, we've been forced to reboot servers because hot swap hasn't "just worked." Thanks for the answers to look more into the SATA controller. I've included the lspci output for the problematic system above (hostname: fs-2). I could still use some help understanding what exactly isn't supported hardware-wise in terms of hot swap for that system. Please let me know what other output besides lspci might be useful. The good news is that hot swap "just worked" today on one of our servers (hostname: www-1), which is very rare for us. Here is the lspci output: [root@www-1 ~]# lspci 00:00.0 RAM memory: nVidia Corporation MCP55 Memory Controller (rev a2) 00:01.0 ISA bridge: nVidia Corporation MCP55 LPC Bridge (rev a3) 00:01.1 SMBus: nVidia Corporation MCP55 SMBus (rev a3) 00:02.0 USB Controller: nVidia Corporation MCP55 USB Controller (rev a1) 00:02.1 USB Controller: nVidia Corporation MCP55 USB Controller (rev a2) 00:04.0 IDE interface: nVidia Corporation MCP55 IDE (rev a1) 00:05.0 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) 00:05.1 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) 00:05.2 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) 00:06.0 PCI bridge: nVidia Corporation MCP55 PCI bridge (rev a2) 00:08.0 Bridge: nVidia Corporation MCP55 Ethernet (rev a3) 00:09.0 Bridge: nVidia Corporation MCP55 Ethernet (rev a3) 00:0b.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0c.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0f.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:18.0 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] HyperTransport Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Miscellaneous Control 00:18.4 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Link Control 00:19.0 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] HyperTransport Configuration 00:19.1 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Address Map 00:19.2 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] DRAM Controller 00:19.3 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Miscellaneous Control 00:19.4 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Link Control 03:00.0 VGA compatible controller: Matrox Graphics, Inc. MGA G200e [Pilot] ServerEngines (SEP1) (rev 02) 04:00.0 PCI bridge: NEC Corporation uPD720400 PCI Express - PCI/PCI-X Bridge (rev 06) 04:00.1 PCI bridge: NEC Corporation uPD720400 PCI Express - PCI/PCI-X Bridge (rev 06) 09:00.0 SCSI storage controller: LSI Logic / Symbios Logic SAS1064ET PCI-Express Fusion-MPT SAS (rev 04)

  Read the article

• Possible to get SSD TRIM (discard) working on ext4 + LVM + software RAID in Linux?

  - by Don MacAskill

  We use RAID1+0 with md on Linux (currently 2.6.37) to create an md device, then use LVM to provide volume management on top of the device, and then use ext4 as our filesystem on the LVM volume groups. With SSDs as the drives, we'd like to see the TRIM commands propagate through the layers (ext4 - LVM - md - SSD) to the devices. It looks like recent 2.6.3x kernels have had a lot of new SSD-related TRIM support added, including lots more coverage of Device Mapper scenarios, but we still can't seem to get it to cascade down properly. Is this possible yet? If so, how? If not, is any progress being made?

  Read the article

• My Logitech G35 headphones aren't very loud on Linux (fedora 14) why?

  - by DarkMantis

  I have recently purchased a set of G35 headphones. They seem to be very loud when I use them on Windows, but when I try and use them on Fedora 14, they are very quiet and I can't seem to make them louder. I have obviously checked the sound settings in Gnome, and they are all up full. I have got ALSA-mixer installed but seems to make no difference. There doesn't seem to be any specific drivers for these headphones for Linux. Anyone know how to make them go a bit louder?

  Read the article

• My linux server takes more than an hour to boot. Suggestions?

  - by jamieb

  I am building a CentOS 5.4 system that boots off a compact flash card using a card reader that emulates an IDE drive. It literally takes about an hour to boot. The ultra-slow part occurs when Grub is loading the kernel. Once that's done, the rest of the boot process only takes about a minute to get to a login prompt. Does anyone have any suggestions? I suspect that it may have to do with UDMA. Everything IDE-related in my BIOS seems to checkout. The read performance hdparm is telling me 1.77 MB/s. Ouch! (But even at that rate, it still shouldn't take an hour to decompress and load the kernel) [root@server ~]# hdparm -tT /dev/hdc /dev/hdc: Timing cached reads: 2444 MB in 2.00 seconds = 1222.04 MB/sec Timing buffered disk reads: 6 MB in 3.39 seconds = 1.77 MB/sec Trying to enable DMA is a no-go though: [root@server ~]# hdparm -d1 /dev/hdc /dev/hdc: setting using_dma to 1 (on) HDIO_SET_DMA failed: Operation not permitted using_dma = 0 (off) Here's some command outputs that might help: System [root@server ~]# uname -a Linux server.localdomain 2.6.18-164.el5xen #1 SMP Thu Sep 3 04:47:32 EDT 2009 i686 i686 i386 GNU/Linux PCI info: [root@server ~]# lspci -v 00:00.0 Host bridge: Intel Corporation 82945G/GZ/P/PL Memory Controller Hub (rev 02) Subsystem: Intel Corporation 82945G/GZ/P/PL Memory Controller Hub Flags: bus master, fast devsel, latency 0 Capabilities: [e0] Vendor Specific Information 00:02.0 VGA compatible controller: Intel Corporation 82945G/GZ Integrated Graphics Controller (rev 02) (prog-if 00 [VGA controller]) Subsystem: Intel Corporation 82945G/GZ Integrated Graphics Controller Flags: bus master, fast devsel, latency 0, IRQ 10 Memory at fdf00000 (32-bit, non-prefetchable) [size=512K] I/O ports at ff00 [size=8] Memory at d0000000 (32-bit, prefetchable) [size=256M] Memory at fdf80000 (32-bit, non-prefetchable) [size=256K] Capabilities: [90] Message Signalled Interrupts: 64bit- Queue=0/0 Enable- Capabilities: [d0] Power Management version 2 00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 (rev 01) (prog-if 00 [UHCI]) Subsystem: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 Flags: bus master, medium devsel, latency 0, IRQ 16 I/O ports at fe00 [size=32] 00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 (rev 01) (prog-if 00 [UHCI]) Subsystem: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 Flags: bus master, medium devsel, latency 0, IRQ 17 I/O ports at fd00 [size=32] 00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 (rev 01) (prog-if 00 [UHCI]) Subsystem: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 Flags: bus master, medium devsel, latency 0, IRQ 18 I/O ports at fc00 [size=32] 00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 (rev 01) (prog-if 00 [UHCI]) Subsystem: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 Flags: bus master, medium devsel, latency 0, IRQ 19 I/O ports at fb00 [size=32] 00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 01) (prog-if 20 [EHCI]) Subsystem: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller Flags: bus master, medium devsel, latency 0, IRQ 16 Memory at fdfff000 (32-bit, non-prefetchable) [size=1K] Capabilities: [50] Power Management version 2 Capabilities: [58] Debug port 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1) (prog-if 01 [Subtractive decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=32 I/O behind bridge: 0000d000-0000dfff Memory behind bridge: fde00000-fdefffff Prefetchable memory behind bridge: 00000000fdd00000-00000000fdd00000 Capabilities: [50] #0d [0000] 00:1f.0 ISA bridge: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge (rev 01) Subsystem: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge Flags: bus master, medium devsel, latency 0 Capabilities: [e0] Vendor Specific Information 00:1f.2 IDE interface: Intel Corporation 82801GB/GR/GH (ICH7 Family) SATA IDE Controller (rev 01) (prog-if 80 [Master]) Subsystem: Intel Corporation 82801GB/GR/GH (ICH7 Family) SATA IDE Controller Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 17 I/O ports at <unassigned> I/O ports at <unassigned> I/O ports at <unassigned> I/O ports at <unassigned> I/O ports at f800 [size=16] Capabilities: [70] Power Management version 2 00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 01) Subsystem: Intel Corporation 82801G (ICH7 Family) SMBus Controller Flags: medium devsel, IRQ 17 I/O ports at 0500 [size=32] 01:04.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) Subsystem: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ Flags: bus master, medium devsel, latency 32, IRQ 18 I/O ports at de00 [size=256] Memory at fdeff000 (32-bit, non-prefetchable) [size=256] Capabilities: [50] Power Management version 2 01:06.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) Subsystem: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ Flags: bus master, medium devsel, latency 32, IRQ 17 I/O ports at dc00 [size=256] Memory at fdefe000 (32-bit, non-prefetchable) [size=256] Capabilities: [50] Power Management version 2 01:07.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) Subsystem: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ Flags: bus master, medium devsel, latency 32, IRQ 19 I/O ports at da00 [size=256] Memory at fdefd000 (32-bit, non-prefetchable) [size=256] Capabilities: [50] Power Management version 2 hdparm ouput: [root@server ~]# hdparm /dev/hdc /dev/hdc: multcount = 0 (off) IO_support = 0 (default 16-bit) unmaskirq = 0 (off) using_dma = 0 (off) keepsettings = 0 (off) readonly = 0 (off) readahead = 256 (on) geometry = 8146/16/63, sectors = 8211168, start = 0 [root@server ~]# hdparm -I /dev/hdc /dev/hdc: ATA device, with non-removable media Model Number: InnoDisk Corp. - iCF4000 4GB Serial Number: 20091023AACA70000753 Firmware Revision: 081107 Standards: Supported: 5 Likely used: 6 Configuration: Logical max current cylinders 8146 8146 heads 16 16 sectors/track 63 63 -- CHS current addressable sectors: 8211168 LBA user addressable sectors: 8211168 device size with M = 1024*1024: 4009 MBytes device size with M = 1000*1000: 4204 MBytes (4 GB) Capabilities: LBA, IORDY(can be disabled) Standby timer values: spec'd by Vendor R/W multiple sector transfer: Max = 2 Current = 2 DMA: mdma0 mdma1 mdma2 udma0 udma1 *udma2 udma3 udma4 Cycle time: min=120ns recommended=120ns PIO: pio0 pio1 pio2 pio3 pio4 Cycle time: no flow control=120ns IORDY flow control=120ns Commands/features: Enabled Supported: * Power Management feature set * WRITE_BUFFER command * READ_BUFFER command * NOP cmd * CFA feature set * Mandatory FLUSH_CACHE HW reset results: CBLID- above Vih Device num = 0 CFA power mode 1: enabled and required by some commands Maximum current = 100ma Checksum: correct

  Read the article

• Full disk encryption on linux (ubuntu) w/o re-installing - possible?

  - by sa125

  Hi - I work at a company that takes security very seriously (like most). Our IT guy came in today to prepare us mentally to re-install our systems after he'll apply the new encryption policy (which will basically scrape our HD clean). For our team this means about a week of re-configuring, installing, and tweaking our desktops until we are back to work capacity - anyone who has to re-install a development machine probably knows what I'm talking about. So, I guess my question is if there's any way to perform full disk encryption on a linux (ubuntu = 9.04) system without having to re-install EVERYTHING [sigh]. IT guy said there isn't any - please prove him wrong. thanks :)

  Read the article

• How to subscribe to a youtube feed from linux command line?

  - by Tim

  I want to subscribe to a youtube channel and automatically download new videos to my linux machine. I know I could do this e.g. with miro, but I will not watch the videos using Miro, want to choose the quality and would like to run it as a cronjob. It should be able to: know which feed entries are new and not download old entries resume (or at least redownload) failed/incomplete downloads from older sessions Are there any complete solutions for this? If not it would be enough for me (maybe even preferable) to just have a command line rss reader that remembers which entries have already been there and writes the new video urls (e.g. http://www.youtube.com/watch?v=FodYFMaI4vQ&feature=youtube_gdata from http://gdata.youtube.com/feeds/api/users/tedxtalks/uploads) into a file. I could then accomplish the rest using a bash script and youtube-dl. What would be programs usable for this purpose?

  Read the article

• Can Linux works as 802.1X authenticator in bridge mode ?

  - by Kartoch

  I want to create a lab for my students with netkit (a network emulator based on 802.1X) to study 802.1X. I can create the authentication server (FreeRadius) and configure the client with XSupplicant connected by a switch (a Linux in bridge mode). I'm looking to a way to configure the switch as Authenticator, i.e.: when the client is connected, the switch only forwards EAP packets to the authentication server. then the switch lets the user access to the local network when the authentication server authorizes the client. At the present time there is a lot of documentation to do this with a wireless point but no one for a switch. Does anyone have an idea or know the good software for it ?

  Read the article

• Linux Software RAID: How to fsck on hard drive?

  - by Rick-Rainer Ludwig

  We have a Linux server running with Software RAID1. We see some issues in /var/log/messages like: unreadable sector. I want to perform a complete fsck on the drive to get some more information, but a fsck /dev/md0 brings a clean due to the Software RAID layer in between. How can I check the real hard drive? Do I need to disassemble the whole RAID? How do I deal with the inconsistency in the partition due to the additional Software RAID header? Does anyone have a good idea for this?

  Read the article

• Why are all Linux commands broken after installing Perl?

  - by user115079

  I installed perl using following command: curl -L http://xrl.us/installperlnix | bash after that i run following command to create soft link ln -sf /usr/local/bin/perl /usr/bin/perl now I'm trying to run commands like dir, mkdir, ll, rm, vi but nothing seems to be working for me. also when i try to login into my shell i get following msg at startup: Last login: Wed Apr 4 21:50:12 2012 from x.y.z.ip -bash: perl: command not found please help. Here is system detail: cat /proc/version Linux version 2.6.18-274.18.1.el5.028stab098.1 (root@rhel5-build-x64) (gcc version 4.1.2 20080704 (Red Hat 4.1.2-46)) #1 SMP Sat Feb 11 15:30:41 MSK 2012 cat /etc/issue CentOS 5.7 32 bit Kernel \r on an \m Don't know if perl was already installed or not. and now i can't check.

  Read the article

• Why Matlab in screen in Linux on PuTTY terminates itself after closing PuTTY session?

  - by Karl

  I connected to a linux server with PuTTY and start a screen session, and start matlab with: matlab -nodesktop Then, I run my matlab code as usual. The code will run for hours. So to test whether screen works, I start another PuTTY session and run top. Then, I close PuTTY session with still-running Matlab (top shows Matlab at 100% CPU usage) in screen. To my surprise, my Matlab process vanished after I close the aforementioned session. I've tried this a few times, and it seems the same thing happened. screen -ls shows that my screens are there but detached. top also shows that my matlab is not there. What might be the possible cause of this? Doesn't screen normally should keep on running even I terminate my PuTTY session?

  Read the article

• How to give a Linux user permission to create backups, but not permission to delete them?

  - by ChocoDeveloper

  I want to set up automated backups that are kept safe from myself (in case a virus pwns me). The problem is the "create" and "delete" permissions are the same thing: write permission. So what can I do about it? Is it possible to decouple the create/delete permissions? Another option could be to let the user "root" make the backups. The problem is my home directory is encrypted, and I don't want to backup everything. Any ideas? For the backups I'm using Deja Dup, which is installed by default in Fedora and Ubuntu.

  Read the article

• How to generate a private/public key pair to use for a Linux server on Windows Azure?

  - by MainMa

  Following Windows Azure documentation, I generated a pair of private/public keys on an Ubuntu machine using the exact comment as given: openssl req -x509 -nodes -days 365 -newkey rsa:2048 -keyout myPrivateKey.key -out myCert.pem When I open the private key in puttygen, the following error is displayed: Couldn't load private key (unrecognised key type) The private key generated by openssl looks correct: -----BEGIN PRIVATE KEY----- MIIEvQIBADANBgkqhkiG6w0xAQEFAASCBKcwggSjAgEsAoIBAQC6OEZ5ULe6F6u2 Cybhqqfqqh2ao9sd2tpqB+HGIoMMHrmnD3YegRgZJIddTQaWKdwaKrYul21YNt5y ... P0RyfL9kDnX/XmIOM38FOoucGvO+Zozsbmgmvw6AUhE0sPhkZnlaodAU1OnfaWJz KpBxkXulBaCJnC8w29dGKng= -----END PRIVATE KEY----- Note that the comments to Azure documentation (the same link as above) report that the pair should be generated using OpenSSL for Windows instead of openssl on Linux. This doesn't help, since the same error appears for a private key generated by OpenSSL for Windows. What am I doing wrong?

  Read the article

• Why no multiple instances of Firefox on Linux as on Windows?

  - by Jack

  On Windows If I run Firefox as user jack, and then try to start another instance of firefox I will be unable to, as one is already running. If I choose to run firefox as administrator, then I can have two instances of firefox, separate from each other side by side, because they are under different user accounts. This does not seem to be true on Linux. As user jack if I start firefox, like on windows I am unable to start a new instance. If I open a terminal and change to root, set XAUTHORITY to jacks .Xauthority and try to start firefox as root....I get the error that firefox is already running. Why is this? Please don't spare any technical details in your answers....thankyou.

  Read the article

• Tiny linux box with 2xGbLAN, WLAN and 10MB/s AES throughput?

  - by Nakedible

  I'd like to find a small linux box with the following specifications: Small (mini-ITX size is OK) Fanless Runs Debian At least two gigabit network interfaces WLAN that supports "host ap" with hostapd + mac80211 in AP mode Can encrypt AES at least 10 megabytes per second Total cost $300 or less Solutions from multiple parts also accepted - I can buy an external network card etc. and build the box myself if the components are available. If you don't know about the "host ap" thing, just suggest your solution, I'll find out if I can get that resolved. If I can't get all that, I can possibly skip the "runs Debian" part, and I can definitely skip the hostapd part if the box can be a wireless access point with multiple ESSIDs out of the box. Something like Asus RT-N16 is close - doesn't run Debian easily, and probably doesn't encrypt AES fast enough. Something like Zotac ZBOX HD-ID11 is also close - no idea which WLAN card it has and it lacks second gigabit interface, but otherwise nice.

  Read the article

• How do I change the document root of a Linux Apache server?

  - by Daryl Spitzer

  I'm trying to learn how to configure an Apache HTTP server (with which I have no experience) someone else has setup in a VM running Ubuntu 8.04. I know the server is running, since I get "<html><body><h1>It works!</h1></body></html>" when I go to http://1.2.3.4/ (where 1.2.3.4 is the VM's IP number). I found apache2.conf and httpd.conf (among other files) in /etc/apache2/. httpd.conf is empty. I tried adding DocumentRoot "/home/username/temp" into /etc/apache2/httpd.conf and put some simple HTML in /home/username/temp/index.html. But when I reload http://1.2.3.4/ there's no change. Do I need to restart httpd to get it to accept the change to DocumentRoot?

  Read the article

• How to calculate time spent for Linux system administration?

  - by Jaakko

  I would love figuring out how much time I actually have spent in shell performing administrative duties. For billing of course, this information is not sufficient, but it would be helpful to figure out how much time I have actually spent in shell. My question is: How anyone got tips on how to calculate time spent in shell (in hours + minutes), let's say per user account? Could anyone recommend a software that could be used to analyze this time? Optionally I would like to know about ways how to categorise time spent (e.g. 1 hour for Apache, 2 hours for Samba, etc.) Also, your takes on how you monitor your admin time, are also much appreciated! To narrow down the problem, I am specifically interested in ways of tracking time spent in shell for Linux system administration

  Read the article

• In Linux, when I use the PS command, why do I see multiple lines for www-data?

  - by johnlai2004

  I have a LAMP server that uses ubuntu 9.10, apache2, mysql5 and php5. When I login as root through the shell, I run a "ps aux" command and see something like the following www-data 3151 0.1 4.3 220024 31032 ? S 12:22 0:00 /usr/sbin/apache2 -k start www-data 3153 0.2 3.6 214776 26020 ? S 12:22 0:01 /usr/sbin/apache2 -k start www-data 3162 0.3 5.1 225060 36920 ? S 12:26 0:01 /usr/sbin/apache2 -k start www-data 3163 0.1 4.1 218872 29664 ? S 12:26 0:00 /usr/sbin/apache2 -k start How come I see multiple lines for www-data? Does each line represent an actual user on my website? I run into memory issues at times, so I'm trying to determine if these www-data statistics are related.

  Read the article

• Why is mcrypt not included in most Linux distributions?

  - by Daniel Lopez

  libmcrypt is a powerful encryption library that is very popular with PHP-based applications. However, most Linux distributions do not include it. This causes problems for many users that need to download and compile it separately. I am guessing that the reason it is not shipped is related to encryption or patent issues. However, the source code for library itself is hosted and available on sourceforge.net I have been searching unsuccessfully for a document of authoritative post that explains the exact issues why this extension is not bundled with mainstream distributions. Can anyone provide a pointer to such material or provide an explanation?

  Read the article

• Which Linux distributive could you advise for a webserver with PIII-700MHz and 512Mb RAM?

  - by Andrei

  Hi everybody, We need to update our webserver (PIII-700MHz and 512Mb RAM) and could not do that without reinstalling the whole system. However my choice to put Ubuntu 9.10 was probably not the best and the machine works very slow now. Actually, we need it just for simple LAPM configuration and we really want to use the old box for this purpose. It used to have old version of Linux Slackware in which I didn't manage to update PHP due to a very complicated non-standard setup. What would you recommend?

  Read the article

• How to display certain lines from a text file in Linux?

  - by Boaz

  Hi, I guess everyone knows the useful Linux cmd line utilities head and tail. Head allows you to print the first X lines of a file, tail does the same but prints the end of the file. What is a good command to print the middle of a file? something like middle --start 10000000 --count 20 (print the 10,000,000th till th 10,000,010th lines). I'm looking for something that will deal with large files efficiently. I tried tail -n 10000000 | head 10 and it's horrifically slow. Thanks, Boaz

  Read the article

• Linux: How to break a large file into smaller files?

  - by Runcible

  I have a giant file (20 gigs) sitting on my source machine and I need to transfer it to my target machine. For the purposes of this question, let's assume that I do not have network connectivity between the two machines. I need to break this file into a series of smaller files, write the smaller files to DVD(s), then re-assemble everything on the target machine. Both source and destination machines are Linux boxes. Is there a way to accomplish this using tar? I have a feeling that I need to use the --multi-volume parameter. What are my options? I need to be able to specify the size of the volume files, in order to make sure that each one will fit onto a single DVD. Thanks!

  Read the article

• How to erase a SSD to restore factory performance in Linux?

  - by Andy B

  Due to big performance issues with an mdraid-1 array I'd like to pull down from the array one of the devices (Samsung 840 Pro), erase it to restore factory performance and re-add it to the array. The reason I want to do this to one of the SSDs is because the poor performance seems to be related to one specific SSD out of the two (although they are the same brand, model and firmware ver). But how do I erase a SSD from Linux? I mention that hdparm indicates that both drives are frozen at this time. Maybe because they are part of an md array? Thanks in advance!

  Read the article

• What emulator / VM software can I use to create a Win32-portable Linux Guest?

  - by Jotham

  Hi, I want to create a portable VM setup so that I can boot a Linux install regardless of which Windows XP / Windows 7 host machine I am on. I was looking at Qemu but it doesn't appear to have a relatively safe win32 build. Other things like VirtualBox require complete install on the host OS for performance reasons. I'm not so concerned about performance, I just want to run a few curses based applications. My ideal end goal would be a a memory stick of some size with a VM/Emulator I can boot on most WinXP/Windows 7 machines and access my own curses based applications (probably archlinux or debian). Any help would be appreciated. Regards,

  Read the article

< Previous Page | 354 355 356 357 358 359 360 361 362 363 364 365  | Next Page >