Search Results

Search found 9634 results on 386 pages for 'proxy pattern'.

Page 359/386 | < Previous Page | 355 356 357 358 359 360 361 362 363 364 365 366  | Next Page >

• Diagnosing packet loss / high latency in Ubuntu

  - by Sam Gammon

  We have a Linux box (Ubuntu 12.04) running Nginx (1.5.2), which acts as a reverse proxy/load balancer to some Tornado and Apache hosts. The upstream servers are physically and logically close (same DC, sometimes same-rack) and show sub-millisecond latency between them: PING appserver (10.xx.xx.112) 56(84) bytes of data. 64 bytes from appserver (10.xx.xx.112): icmp_req=1 ttl=64 time=0.180 ms 64 bytes from appserver (10.xx.xx.112): icmp_req=2 ttl=64 time=0.165 ms 64 bytes from appserver (10.xx.xx.112): icmp_req=3 ttl=64 time=0.153 ms We receive a sustained load of about 500 requests per second, and are currently seeing regular packet loss / latency spikes from the Internet, even from basic pings: sam@AM-KEEN ~> ping -c 1000 loadbalancer PING 50.xx.xx.16 (50.xx.xx.16): 56 data bytes 64 bytes from loadbalancer: icmp_seq=0 ttl=56 time=11.624 ms 64 bytes from loadbalancer: icmp_seq=1 ttl=56 time=10.494 ms ... many packets later ... Request timeout for icmp_seq 2 64 bytes from loadbalancer: icmp_seq=2 ttl=56 time=1536.516 ms 64 bytes from loadbalancer: icmp_seq=3 ttl=56 time=536.907 ms 64 bytes from loadbalancer: icmp_seq=4 ttl=56 time=9.389 ms ... many packets later ... Request timeout for icmp_seq 919 64 bytes from loadbalancer: icmp_seq=918 ttl=56 time=2932.571 ms 64 bytes from loadbalancer: icmp_seq=919 ttl=56 time=1932.174 ms 64 bytes from loadbalancer: icmp_seq=920 ttl=56 time=932.018 ms 64 bytes from loadbalancer: icmp_seq=921 ttl=56 time=6.157 ms --- 50.xx.xx.16 ping statistics --- 1000 packets transmitted, 997 packets received, 0.3% packet loss round-trip min/avg/max/stddev = 5.119/52.712/2932.571/224.629 ms The pattern is always the same: things operate fine for a while (<20ms), then a ping drops completely, then three or four high-latency pings (1000ms), then it settles down again. Traffic comes in through a bonded public interface (we will call it bond0) configured as such: bond0 Link encap:Ethernet HWaddr 00:xx:xx:xx:xx:5d inet addr:50.xx.xx.16 Bcast:50.xx.xx.31 Mask:255.255.255.224 inet6 addr: <ipv6 address> Scope:Global inet6 addr: <ipv6 address> Scope:Link UP BROADCAST RUNNING MASTER MULTICAST MTU:1500 Metric:1 RX packets:527181270 errors:1 dropped:4 overruns:0 frame:1 TX packets:413335045 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:240016223540 (240.0 GB) TX bytes:104301759647 (104.3 GB) Requests are then submitted via HTTP to upstream servers on the private network (we can call it bond1), which is configured like so: bond1 Link encap:Ethernet HWaddr 00:xx:xx:xx:xx:5c inet addr:10.xx.xx.70 Bcast:10.xx.xx.127 Mask:255.255.255.192 inet6 addr: <ipv6 address> Scope:Link UP BROADCAST RUNNING MASTER MULTICAST MTU:1500 Metric:1 RX packets:430293342 errors:1 dropped:2 overruns:0 frame:1 TX packets:466983986 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:77714410892 (77.7 GB) TX bytes:227349392334 (227.3 GB) Output of uname -a: Linux <hostname> 3.5.0-42-generic #65~precise1-Ubuntu SMP Wed Oct 2 20:57:18 UTC 2013 x86_64 GNU/Linux We have customized sysctl.conf in an attempt to fix the problem, with no success. Output of /etc/sysctl.conf (with irrelevant configs omitted): # net: core net.core.netdev_max_backlog = 10000 # net: ipv4 stack net.ipv4.tcp_ecn = 2 net.ipv4.tcp_sack = 1 net.ipv4.tcp_fack = 1 net.ipv4.tcp_tw_reuse = 1 net.ipv4.tcp_tw_recycle = 0 net.ipv4.tcp_timestamps = 1 net.ipv4.tcp_window_scaling = 1 net.ipv4.tcp_no_metrics_save = 1 net.ipv4.tcp_max_syn_backlog = 10000 net.ipv4.tcp_congestion_control = cubic net.ipv4.ip_local_port_range = 8000 65535 net.ipv4.tcp_syncookies = 1 net.ipv4.tcp_synack_retries = 2 net.ipv4.tcp_thin_dupack = 1 net.ipv4.tcp_thin_linear_timeouts = 1 net.netfilter.nf_conntrack_max = 99999999 net.netfilter.nf_conntrack_tcp_timeout_established = 300 Output of dmesg -d, with non-ICMP UFW messages suppressed: [508315.349295 < 19.852453>] [UFW BLOCK] IN=bond1 OUT= MAC=<mac addresses> SRC=118.xx.xx.143 DST=50.xx.xx.16 LEN=68 TOS=0x00 PREC=0x00 TTL=51 ID=43221 PROTO=ICMP TYPE=3 CODE=1 [SRC=50.xx.xx.16 DST=118.xx.xx.143 LEN=40 TOS=0x00 PREC=0x00 TTL=249 ID=10220 DF PROTO=TCP SPT=80 DPT=53817 WINDOW=8190 RES=0x00 ACK FIN URGP=0 ] [517787.732242 < 0.443127>] Peer 190.xx.xx.131:59705/80 unexpectedly shrunk window 1155488866:1155489425 (repaired) How can I go about diagnosing the cause of this problem, on a Debian-family Linux box?

  Read the article

• Intelligent "Subtraction" of one text logfile from another

  - by Vi

  Example: Application generates large text log file A with many different messages. It generates similarly large log file B when does not function correctly. I want to see what messages in file B are essentially new, i.e. to filter-out everything from A. Trivial prototype is: Sort | uniq both files Join files sort | uniq -c grep -v "^2" This produces symmetric difference and inconvenient. How to do it better? (including non-symmetric difference and preserving of messages order in B) Program should first analyse A and learn which messages are common, then analyse B showing with messages needs attention. Ideally it should automatically disregard things like timestamps, line numbers or other volatile things. Example. A: 0:00:00.234 Received buffer 0x324234 0:00:00.237 Processeed buffer 0x324234 0:00:00.238 Send buffer 0x324255 0:00:03.334 Received buffer 0x324255 0:00:03.337 Processeed buffer 0x324255 0:00:03.339 Send buffer 0x324255 0:00:05.171 Received buffer 0x32421A 0:00:05.173 Processeed buffer 0x32421A 0:00:05.178 Send buffer 0x32421A B: 0:00:00.134 Received buffer 0x324111 0:00:00.137 Processeed buffer 0x324111 0:00:00.138 Send buffer 0x324111 0:00:03.334 Received buffer 0x324222 0:00:03.337 Processeed buffer 0x324222 0:00:03.338 Error processing buffer 0x324222 0:00:03.339 Send buffer 0x3242222 0:00:05.271 Received buffer 0x3242FA 0:00:05.273 Processeed buffer 0x3242FA 0:00:05.278 Send buffer 0x3242FA 0:00:07.280 Send buffer 0x3242FA failed Result: 0:00:03.338 Error processing buffer 0x324222 0:00:07.280 Send buffer 0x3242FA failed One of ways of solving it can be something like that: Split each line to logical units: 0:00:00.134 Received buffer 0x324111,0:00:00.134,Received,buffer,0x324111,324111,Received buffer, \d:\d\d:\d\d\.\d\d\d, \d+:\d+:\d+.\d+, 0x[0-9A-F]{6}, ... It should find individual words, simple patterns in numbers, common layouts (e.g. "some date than text than number than text than end_of_line"), also handle combinations of above. As it is not easy task, user assistance (adding regexes with explicit "disregard that","make the main factor","don't split to parts","consider as date/number","take care of order/quantity of such messages" rules) should be supported (but not required) for it. Find recurring units and "categorize" lines, filter out too volatile things like timestamps, addresses or line numbers. Analyse the second file, find things that has new logical units (one-time or recurring), or anything that will "amaze" the system which has got used to the first file. Example of doing some bit of this manually: $ cat A | head -n 1 0:00:00.234 Received buffer 0x324234 $ cat A | egrep -v "Received buffer" | head -n 1 0:00:00.237 Processeed buffer 0x324234 $ cat A | egrep -v "Received buffer|Processeed buffer" | head -n 1 0:00:00.238 Send buffer 0x324255 $ cat A | egrep -v "Received buffer|Processeed buffer|Send buffer" | head -n 1 $ cat B | egrep -v "Received buffer|Processeed buffer|Send buffer" 0:00:03.338 Error processing buffer 0x324222 0:00:07.280 Send buffer 0x3242FA failed This is a boring thing (there are a lot of message types); also I can accidentally include some too broad pattern. Also it can't handle complicated things like interrelation between messages. I know that it is AI-related. May be there are already developed tools?

  Read the article

• Active Directory Time Synchronisation - Time-Service Event ID 50

  - by George

  I have an Active Directory domain with two DCs. The first DC in the forest/domain is Server 2012, the second is 2008 R2. The first DC holds the PDC Emulator role. I sporadically receive a warning from the Time-Service source, event ID 50: The time service detected a time difference of greater than %1 milliseconds for %2 seconds. The time difference might be caused by synchronization with low-accuracy time sources or by suboptimal network conditions. The time service is no longer synchronized and cannot provide the time to other clients or update the system clock. When a valid time stamp is received from a time service provider, the time service will correct itself. Time sync in the domain is configured with the second DC to synchronise using the /syncfromflags:DOMHIER flag. The first DC is configured to sync time using a /syncfromflags:MANUAL /reliable:YES, from a peerlist consisting of a number of UK based stratum 2 servers, such as ntp2d.mcc.ac.uk. I'm confused why I receive this event warning. It implies that my PDC emulator cannot synchronise time with a supposedly reliable external time source, and it quotes a time difference of 5 seconds for 900 seconds. It's worth also mentioning that I used to use a UK pool from ntp.org but I would receive the warning much more often. Since updating to a number of UK based academic time servers, it seems to be more reliable. Can someone with more experience shed some light on this - perhaps it is purely transient? Should I disregard the warning? Is my configuration sound? EDIT: I should add that the DCs are virtual, and installed on two separate VMware ESXi/vSphere physical hosts. I can also confirm that as per MDMarra's comment and best practice, VMware timesync is disabled, since: c:\Program Files\VMware\VMware Tools\VMwareToolboxCmd.exe timesync status returns Disabled. EDIT 2 Some strange new issue has cropped up. I've noticed a pattern. Originally, the event ID 50 warnings would occur at about 1230pm each day. This is interesting since our veeam backup happens at 12 midday. Since I made the changes discussed here, I now receive an event ID 51 instead of 50. The new warning says that: The time sample received from peer server.ac.uk differs from the local time by -40 seconds (Or approximately 40 seconds). This has happened two days in a row. Now I'm even more confused. Obviously the time never updates until I manually intervene. The issue seems to be related to virtualisation and veeam. Something may be occuring when veeam is backing up the PDCe. Any suggestions? UPDATE & SUMMARY msemack's excellent list of resources below (the accepted answer) provided enough information to correctly configure the time service in the domain. This should be the first port of call for any future people looking to verify their configuration. The final "40 second jump" issue I have resolved (there are no more warnings) through adjusting the VMware time sync settings as noted in the veeam knowledge base article here: http://www.veeam.com/kb1202 In any case, should any future reader use ESXi, veeam or not, the resources here are an excellent source of information on the time sync topic and msemack's answer is particularly invaluable.

  Read the article

• Windows can see Ubuntu Server printer, but can't print to it

  - by Mike

  I have an old desktop that I'm trying to set up as a home backup/print server. Backup was trivial, but am having issues getting the printing to work. The printer is connected to the server running Ubuntu Server 9.10 (no gui). If I access the printer via http://hostname:631/printers/, I am able to print a test page, so I know the printer is working; however, I am having no luck from Windows. Windows can see the printer when browsed via \hostname\, but I am unable to connect. Windows says "Windows cannot connect to the printer" without indicating why. Any suggestions? From /etc/samba/smb.conf: [global] workgroup = WORKGROUP dns proxy = no security = user username map = /etc/samba/smbusers encrypt passwords = true passdb backend = tdbsam obey pam restrictions = yes unix password sync = yes passwd program = /usr/bin/passwd %u passwd chat = *Enter\snew\s*\spassword:* %n\n *Retype\snew\s*\spassword:* %n\n *password\supdated\ssuccessfully* . pam password change = yes map to guest = bad user load printers = yes printing = cups printcap name = cups [printers] comment = All Printers browseable = no path = /var/spool/samba writable = no printable = yes guest ok = yes read only = yes create mask = 0700 [print$] comment = Printer Drivers path = /var/lib/samba/printers browseable = yes read only = yes guest ok = yes From /etc/cups/cupsd.conf: LogLevel warn SystemGroup lpadmin Port 631 Listen /var/run/cups/cups.sock Browsing On BrowseOrder allow,deny BrowseAllow all BrowseRemoteProtocols CUPS BrowseAddress @LOCAL BrowseLocalProtocols CUPS dnssd DefaultAuthType Basic <Location /> Order allow,deny Allow all </Location> <Location /admin> Order allow,deny Allow all </Location> <Location /admin/conf> AuthType Default Require user @SYSTEM Order allow,deny Allow all </Location> <Policy default> <Limit Send-Document Send-URI Hold-Job Release-Job Restart-Job Purge-Jobs Set-Job-Attributes Create-Job-Subscription Renew-Subscription Cancel-Subscription Get-Notifications Reprocess-Job Cancel-Current-Job Suspend-Current-Job Resume-Job CUPS-Move-Job CUPS-Get-Document> Require user @OWNER @SYSTEM Order deny,allow </Limit> <Limit CUPS-Add-Modify-Printer CUPS-Delete-Printer CUPS-Add-Modify-Class CUPS-Delete-Class CUPS-Set-Default CUPS-Get-Devices> AuthType Default Require user @SYSTEM Order deny,allow </Limit> <Limit Pause-Printer Resume-Printer Enable-Printer Disable-Printer Pause-Printer-After-Current-Job Hold-New-Jobs Release-Held-New-Jobs Deactivate-Printer Activate-Printer Restart-Printer Shutdown-Printer Startup-Printer Promote-Job Schedule-Job-After CUPS-Accept-Jobs CUPS-Reject-Jobs> AuthType Default Require user @SYSTEM Order deny,allow </Limit> <Limit CUPS-Authenticate-Job> Require user @OWNER @SYSTEM Order deny,allow </Limit> <Limit All> Order deny,allow </Limit> </Policy> <Policy authenticated> <Limit Create-Job Print-Job Print-URI> AuthType Default Order deny,allow </Limit> <Limit Send-Document Send-URI Hold-Job Release-Job Restart-Job Purge-Jobs Set-Job-Attributes Create-Job-Subscription Renew-Subscription Cancel-Subscription Get-Notifications Reprocess-Job Cancel-Current-Job Suspend-Current-Job Resume-Job CUPS-Move-Job CUPS-Get-Document> AuthType Default Require user @OWNER @SYSTEM Order deny,allow </Limit> <Limit CUPS-Add-Modify-Printer CUPS-Delete-Printer CUPS-Add-Modify-Class CUPS-Delete-Class CUPS-Set-Default> AuthType Default Require user @SYSTEM Order deny,allow </Limit> <Limit Pause-Printer Resume-Printer Enable-Printer Disable-Printer Pause-Printer-After-Current-Job Hold-New-Jobs Release-Held-New-Jobs Deactivate-Printer Activate-Printer Restart-Printer Shutdown-Printer Startup-Printer Promote-Job Schedule-Job-After CUPS-Accept-Jobs CUPS-Reject-Jobs> AuthType Default Require user @SYSTEM Order deny,allow </Limit> <Limit Cancel-Job CUPS-Authenticate-Job> AuthType Default Require user @OWNER @SYSTEM Order deny,allow </Limit> <Limit All> Order deny,allow </Limit> </Policy>

  Read the article

• Single-Signon options for Exchange 2010

  - by freiheit

  We're working on a project to migrate employee email from Unix/open-source (courier IMAP, exim, squirrelmail, etc) to Exchange 2010, and trying to figure out options for single-signon for Outlook Web Access. So far all the options I've found are very ugly and "unsupportable", and may simply not work with Forefront. We already have JA-SIG CAS for token-based single-signon and Shibboleth for SAML. Users are directed to a simple in-house portal (a Perl CGI, really) that they use to sign in to most stuff. We have an HA OpenLDAP cluster that's already synchronized against another AD domain and will be synchronized with the AD domain Exchange will be using. CAS authenticates against LDAP. The portal authenticates against CAS. Shibboleth authenticates with CAS but pulls additional data from LDAP. We're moving in the direction of having web services authenticate against CAS or Shibboleth. (Students are already on SAML/Shibboleth authenticated Google Apps for Education) With Squirrelmail we have a horrible hack linked to from that portal page that authenticates against CAS, gets your original plaintext password (yes, I know, evil), and gives you an HTTP form pre-filled with all the necessary squirrelmail login details with javaScript onLoad stuff to immediately submit the form. Trying to find out exactly what is possible with Exchange/OWA seems to be difficult. "CAS" is both the acronym for our single-signon server and an Exchange component. From what I've been able to tell there's an addon for Exchange that does SAML, but only for federating things like free/busy calendar info, not authenticating users. Plus it costs additional money so there's no way to experiment with it to see if it can be coaxed into doing what we want. Our plans for the Exchange cluster involve Forefront Threat Management Gateway (the new ISA) in the DMZ front-ending the CAS servers. So, the real question: Has anybody managed to make Exchange authenticate with CAS (token-based single-signon) or SAML, or with something I can reasonably likely make authenticate with one of those (such as anything that will accept apache's authentication)? With Forefront? Failing that, anybody have some tips on convincing OWA Forms Based Authentication (FBA) into letting us somehow "pre-login" the user? (log in as them and pass back cookies to the user, or giving the user a pre-filled form that autosubmits like we do with squirrelmail). This is the least-favorite option for a number of reasons, but it would (just barely) satisfy our requirements. From what I hear from the guy implementing Forefront, we may have to set OWA to basic authentication and do forms in Forefront for authentication, so it's possible this isn't even possible. I did find CasOwa, but it only mentions Exchange 2007, looks kinda scary, and as near as I can tell is mostly the same OWA FBA hack I was considering slightly more integrated with the CAS server. It also didn't look like many people had had much success with it. And it may not work with Forefront. There's also "CASifying Outlook Web Access 2", but that one scares me, too, and involves setting up a complex proxy config, which seems more likely to break. And, again, doesn't look like it would work with Forefront. Am I missing something with Exchange SAML (OWA Federated whatchamacallit) where it is possible to configure to do user authentication and not just free/busy access authorization?

  Read the article

• How to redirect http requests to https (nginx)

  - by spuder

  There appear to be many questions and guides out there that instruct how to setup nginx to redirect http requests to https. Many are outdated, or just flat out wrong. # MANAGED BY PUPPET upstream gitlab { server unix:/home/git/gitlab/tmp/sockets/gitlab.socket; } # setup server with or without https depending on gitlab::gitlab_ssl variable server { listen *:80; server_name gitlab.localdomain; server_tokens off; root /nowhere; rewrite ^ https://$server_name$request_uri permanent; } server { listen *:443 ssl default_server; server_name gitlab.localdomain; server_tokens off; root /home/git/gitlab/public; ssl on; ssl_certificate /etc/ssl/certs/ssl-cert-snakeoil.pem; ssl_certificate_key /etc/ssl/private/ssl-cert-snakeoil.key; ssl_protocols SSLv3 TLSv1 TLSv1.1 TLSv1.2; ssl_ciphers AES:HIGH:!ADH:!MDF; ssl_prefer_server_ciphers on; # individual nginx logs for this gitlab vhost access_log /var/log/nginx/gitlab_access.log; error_log /var/log/nginx/gitlab_error.log; location / { # serve static files from defined root folder;. # @gitlab is a named location for the upstream fallback, see below try_files $uri $uri/index.html $uri.html @gitlab; } # if a file, which is not found in the root folder is requested, # then the proxy pass the request to the upsteam (gitlab puma) location @gitlab { proxy_read_timeout 300; # https://github.com/gitlabhq/gitlabhq/issues/694 proxy_connect_timeout 300; # https://github.com/gitlabhq/gitlabhq/issues/694 proxy_redirect off; proxy_set_header X-Forwarded-Proto $scheme; proxy_set_header X-Forwarded-Ssl on; proxy_set_header Host $http_host; proxy_set_header X-Real-IP $remote_addr; proxy_pass http://gitlab; } } I've restarted after every configuration change, and yet I still only get the 'Welcome to nginx' page when visiting http://192.168.33.10. whereas https://192.168.33.10 works perfectly. Why will nginx still not redirect http requests to https? I've also tried the following configurations listen *:80; server_name <%= @fqdn %>; #root /nowhere; #rewrite ^ https://$server_name$request_uri? permanent; #rewrite ^ https://$server_name$request_uri permanent; #return 301 https://$server_name$request_uri; #return 301 http://$server_name$request_uri; #return 301 http://192.168.33.10$request_uri; return 301 http://$host$request_uri; The logs tailf /var/log/nginx/access.log 192.168.33.1 - - [22/Oct/2013:03:41:39 +0000] "GET / HTTP/1.1" 304 0 "-" "Mozilla/5.0 (Macintosh; Intel Mac OS X 10.8; rv:24.0) Gecko/20100101 Firefox/24.0" 192.168.33.1 - - [22/Oct/2013:03:44:43 +0000] "GET / HTTP/1.1" 200 133 "-" "Mozilla/5.0 (Macintosh; Intel Mac OS X 10.8; rv:24.0) Gecko/20100101 Firefox/24.0" tailf /var/log/nginx/gitlab_error.lob 2013/10/22 02:29:14 [crit] 27226#0: *1 connect() to unix:/home/git/gitlab/tmp/sockets/gitlab.socket failed (2: No such file or directory) while connecting to upstream, client: 192.168.33.1, server: gitlab.localdomain, request: "GET / HTTP/1.1", upstream: "http://unix:/home/git/gitlab/tmp/sockets/gitlab.socket:/", host: "192.168.33.10" Resources http://wiki.nginx.org/Pitfalls How to make nginx redirect How to force or redirect to SSL in nginx? nginx ssl redirect Nginx & Https Redirection https://www.tinywp.in/301-redirect-wordpress/ How to force or redirect to SSL in nginx?

  Read the article

• Routing not working correctly using the laravel framework

  - by samayres1992

  I'm using the book wrote by one of the guys that created laravel, so I'd like to think for the most part this code isn't horribly wrong. My server is setup with nginx serving all static files and apache2 serving php. My config for each are the following: apache2: <VirtualHost *> # Host that will serve this project. ServerName litl.it # The location of our projects public directory. DocumentRoot /var/www/litl.it/laravel/public # Useful logs for debug. CustomLog /var/log/apache.access.log common ErrorLog /var/log/apache.error.log # Rewrites for pretty URLs, better not to rely on .htaccess. <Directory /var/www/litl.it/laravel/public> <IfModule mod_rewrite.c> Options -MultiViews RewriteEngine On RewriteCond %{REQUEST_FILENAME} !-f RewriteRule ^ index.php [L] </IfModule> </Directory> nginx: server { # Port that the web server will listen on. listen 80; # Host that will serve this project. server_name litl.it *.litl.it; # Useful logs for debug. access_log /var/log/nginx.access.log; error_log /var/log/nginx.error.log; rewrite_log on; # The location of our projects public directory. root /var/www/litl.it/laravel/public; # Point index to the Laravel front controller. index index.php; location / { # URLs to attempt, including pretty ones. try_files $uri $uri/ /index.php?$query_string; } # Remove trailing slash to please routing system. if (!-d $request_filename) { rewrite ^/(.+)/$ /$1 permanent; } # PHP FPM configuration. location ~* \.php$ { proxy_pass http://127.0.0.1:8080; include /etc/nginx/proxy_params; try_files index index.php $uri =404; include /etc/nginx/fastcgi_params; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME $document_root/php/$fastcgi_script_name; } # We don't need .ht files with nginx. location ~ /\.ht { deny all; } location @proxy { proxy_pass http://127.0.0.1:8080; include /etc/nginx/proxy_params; } error_page 403 /error/403.html; error_page 404 /error/404.html; error_page 405 /error/405.html; error_page 500 501 502 503 504 /error/5xx.html; location ^~ /error/ { internal; root /var/www/litl.it/lavarel/public/error; } } I'm including these server configs, as I feel this maybe the issue? Here is my incredibly basic routing file that should return "routing is working" on domain.com/test but instead it just returns the homepage. <?php Route::get('/', function() { return View::make('hello'); }); Route::get('/test', function() { return "routing is working"; }); Any ideas where I'm going wrong, I'm following this tutorial very closely and I'm confused why there is issue. Thanks!

  Read the article

• Simple Cisco ASA 5505 config issue

  - by Ben Sebborn

  I have a Cisco ASA setup with two interfaces: inside: 192.168.2.254 / 255.255.255.0 SecLevel:100 outside: 192.168.3.250 / 255.255.255.0 SecLevel: 0 I have a static route setup to allow PCs on the inside network to access the internet via a gateway on the outside interface (3.254): outside 0.0.0.0 0.0.0.0 192.168.3.254 This all works fine. I now need to be able to access a PC on the outside interface (3.253) from a PC on the inside interface on port 35300. I understand I should be able to do this with no problems, as I'm going from a higher security level to a lower one. However I can't get any connection. Do I need to set up a seperate static route? Perhaps the route above is overriding what I need to be able to do (is it routing ALL traffic through the gateway?) Any advice on how to do this would be apprecaited. I am configuring this via ASDM but the config can be seen as below: Result of the command: "show running-config" : Saved : ASA Version 8.2(5) ! hostname ciscoasa domain-name xxx.internal names name 192.168.2.201 dev.xxx.internal description Internal Dev server name 192.168.2.200 Newserver ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 ! interface Ethernet0/3 shutdown ! interface Ethernet0/4 shutdown ! interface Ethernet0/5 shutdown ! interface Ethernet0/6 shutdown ! interface Ethernet0/7 shutdown ! interface Vlan1 nameif inside security-level 100 ip address 192.168.2.254 255.255.255.0 ! interface Vlan2 nameif outside security-level 0 ip address 192.168.3.250 255.255.255.0 ! ! time-range Workingtime periodic weekdays 9:00 to 18:00 ! ftp mode passive clock timezone GMT/BST 0 clock summer-time GMT/BDT recurring last Sun Mar 1:00 last Sun Oct 2:00 dns domain-lookup inside dns server-group DefaultDNS name-server Newserver domain-name xxx.internal same-security-traffic permit inter-interface object-group service Mysql tcp port-object eq 3306 object-group protocol TCPUDP protocol-object udp protocol-object tcp access-list inside_access_in extended permit ip any any access-list outside_access_in remark ENABLES OUTSDIE ACCESS TO DEV SERVER! access-list outside_access_in extended permit tcp any interface outside eq www time-range Workingtime inactive access-list outside_access_in extended permit tcp host www-1.xxx.com interface outside eq ssh access-list inside_access_in_1 extended permit tcp any any eq www access-list inside_access_in_1 extended permit tcp any any eq https access-list inside_access_in_1 remark Connect to SSH services access-list inside_access_in_1 extended permit tcp any any eq ssh access-list inside_access_in_1 remark Connect to mysql server access-list inside_access_in_1 extended permit tcp any host mysql.xxx.com object-group Mysql access-list inside_access_in_1 extended permit tcp any host mysql.xxx.com eq 3312 access-list inside_access_in_1 extended permit object-group TCPUDP host Newserver any eq domain access-list inside_access_in_1 extended permit icmp any any access-list inside_access_in_1 remark Draytek Admin access-list inside_access_in_1 extended permit tcp any 192.168.3.0 255.255.255.0 eq 4433 access-list inside_access_in_1 remark Phone System access-list inside_access_in_1 extended permit tcp any 192.168.3.0 255.255.255.0 eq 35300 log disable pager lines 24 logging enable logging asdm warnings logging from-address [email protected] logging recipient-address [email protected] level errors mtu inside 1500 mtu outside 1500 ip verify reverse-path interface inside ip verify reverse-path interface outside ipv6 access-list inside_access_ipv6_in permit tcp any any eq www ipv6 access-list inside_access_ipv6_in permit tcp any any eq https ipv6 access-list inside_access_ipv6_in permit tcp any any eq ssh ipv6 access-list inside_access_ipv6_in permit icmp6 any any icmp unreachable rate-limit 1 burst-size 1 icmp permit any outside no asdm history enable arp timeout 14400 global (outside) 1 interface nat (inside) 1 0.0.0.0 0.0.0.0 static (inside,outside) tcp interface www dev.xxx.internal www netmask 255.255.255.255 static (inside,outside) tcp interface ssh dev.xxx.internal ssh netmask 255.255.255.255 access-group inside_access_in in interface inside control-plane access-group inside_access_in_1 in interface inside access-group inside_access_ipv6_in in interface inside access-group outside_access_in in interface outside route outside 0.0.0.0 0.0.0.0 192.168.3.254 10 route outside 192.168.3.252 255.255.255.255 192.168.3.252 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 timeout floating-conn 0:00:00 dynamic-access-policy-record DfltAccessPolicy aaa authentication telnet console LOCAL aaa authentication enable console LOCAL

  Read the article

• Why are my httpd mpm_prefork processes being reaped so quickly?

  - by Dan Pritts

  We've got a system running RHEL6, x64. We are using a local installation of apache 2.2.22 from source. we serve primarily: mod_perl applications (with a local installation of perl 5.16.0) tomcat applications proxied with mod_jk Here is some context; the main question is below. All of this talks to an Oracle backend. We are having issues with Oracle becoming unresponsive. We think this is because we're hitting the maximum process limit in oracle. We've upped the process limit, but now we are hitting memory pressure on the oracle server. We have tons of oracle sessions sitting idle. I can trace a bunch of them back to the httpd processes. We have mod_perl's Apache::DBI start up a new connection to the database with each httpd child that's spawned. We are concerned that these are not always getting closed out properly when the httpd's exit...and the httpd's are exiting very frequently. I know that it would be good to modify the mod_perl applications to use some better form of db connection pooling; we plan to pursue that but would like to solve our immediate problem sooner. So here's the main question. We are using the prefork MPM. The apache child processes are lasting at most a few minutes. Log analysis shows that each one is serving fewer than 50 clients before exiting; the last request each child serves is OPTIONS * HTTP/1.0 on some sort of internal connection; I'm under the impression that this is a "ping" from the master process. I've adjusted the MPM config as follows. I didn't want to raise MinSpareServers too high, because, after all, i'm trying to minimize the number of sessions to oracle. MinSpareServers 5 MaxSpareServers 30 MaxClients 150 MaxRequestsPerChild 10000 Right now we're serving 250-300 requests per minute. We've got 21 httpd's running, the eldest (other than the master, owned by root) being 3 minutes old. This rate of reaping of the apache children really seems excessive. What could be causing it? Apache was built with: $ ./configure --prefix=/opt/apache --with-ssl=/usr/lib --enable-expires --enable-ext-filter --enable-info --enable-mime-magic --enable-rewrite --enable-so --enable-speling --enable-ssl --enable-usertrack --enable-proxy --enable-headers --enable-log-forensic Apache config info: % /opt/apache/bin/httpd -V Server version: Apache/2.2.22 (Unix) Server built: Jul 23 2012 22:30:13 Server's Module Magic Number: 20051115:30 Server loaded: APR 1.4.5, APR-Util 1.4.1 Compiled using: APR 1.4.5, APR-Util 1.4.1 Architecture: 64-bit Server MPM: Prefork threaded: no forked: yes (variable process count) Server compiled with.... -D APACHE_MPM_DIR="server/mpm/prefork" -D APR_HAS_SENDFILE -D APR_HAS_MMAP -D APR_HAVE_IPV6 (IPv4-mapped addresses enabled) -D APR_USE_SYSVSEM_SERIALIZE -D APR_USE_PTHREAD_SERIALIZE -D SINGLE_LISTEN_UNSERIALIZED_ACCEPT -D APR_HAS_OTHER_CHILD -D AP_HAVE_RELIABLE_PIPED_LOGS -D DYNAMIC_MODULE_LIMIT=128 -D HTTPD_ROOT="/opt/apache" -D SUEXEC_BIN="/opt/apache/bin/suexec" -D DEFAULT_PIDLOG="logs/httpd.pid" -D DEFAULT_SCOREBOARD="logs/apache_runtime_status" -D DEFAULT_LOCKFILE="logs/accept.lock" -D DEFAULT_ERRORLOG="logs/error_log" -D AP_TYPES_CONFIG_FILE="conf/mime.types" -D SERVER_CONFIG_FILE="conf/httpd.conf" modules are compiled into apache rather than shared libs: % /opt/apache/bin/httpd -l Compiled in modules: core.c mod_authn_file.c mod_authn_default.c mod_authz_host.c mod_authz_groupfile.c mod_authz_user.c mod_authz_default.c mod_auth_basic.c mod_ext_filter.c mod_include.c mod_filter.c mod_log_config.c mod_log_forensic.c mod_env.c mod_mime_magic.c mod_expires.c mod_headers.c mod_usertrack.c mod_setenvif.c mod_version.c mod_proxy.c mod_proxy_connect.c mod_proxy_ftp.c mod_proxy_http.c mod_proxy_scgi.c mod_proxy_ajp.c mod_proxy_balancer.c mod_ssl.c prefork.c http_core.c mod_mime.c mod_status.c mod_autoindex.c mod_asis.c mod_info.c mod_cgi.c mod_negotiation.c mod_dir.c mod_actions.c mod_speling.c mod_userdir.c mod_alias.c mod_rewrite.c mod_so.c One final note - the red hat httpd, apr, and perl packages are all installed, but ldd shows that none of those libraries are linked with the running httpd.

  Read the article

• PC runs very slowly for no apparent reason

  - by GalacticCowboy

  I have a Dell Latitude D820 that I've owned for about 2.5 years. It is a Core 2 Duo T7200 2.0GHz, with 2 GB of RAM, an 80 GB hard drive and an NVidia Quadro 120M video card. The computer was purchased in late November of 2006 with XP Pro, and included a free upgrade to Vista Business. (Vista was available on MSDN but not yet via retail, so the Vista Business upgrades weren't shipped until March of '07.) Since we had an MSDN subscription at the time, I installed Vista Ultimate on it pretty much as soon as I got it. It ran happily until sometime in the spring of 2007 when Media Center (which I had never used except to watch DVDs) started throwing some kind of bizarre SQL (CE?) error. This error would pop up at random times just while using the computer. Furthermore, Media Center would no longer start. I never identified the cause of this error. I had the Vista Business upgrade by this time, so I nuked the machine, installed XP and all the drivers, and then the Vista Business upgrade. Again, it ran happily for a few months and then started behaving badly once again. Vista Business doesn't have Media Center, so this exhibited completely unrelated symptoms. For no apparent reason and at fairly random times, the machine would suddenly appear to freeze up or run very slowly. For example, launching a new application window (any app) might take 30-45 seconds to paint fully. However, Task Manager showed very low CPU load, memory, etc. I tried all the normal stuff (chkdsk, defrag, etc.) and ran several diagnostic programs to try to identify any problems, but none found anything. It eventually reached the point that the computer was all but unusable, so I nuked it again and installed XP. This time I decided to stick with XP instead of going to Vista. However, within the past couple of months it has started to exhibit the same symptoms in XP that I used to see in Vista. The computer is still under Dell warranty until December, but so far they aren't any help unless I can identify a specific problem. A friend (partner in a now-dead business) has an identical machine that was purchased at the same time. His machine exhibits none of these symptoms, which leads me to believe it is a hardware issue, but I can't figure out how to identify it. Any ideas? Utilities? Seen something similar? At this point I can't even identify any pattern to the behavior, but would be willing to run a "stress test"-style app for as long as a couple days if I had any hope that it would find something. EDIT July 17 I'm testing jerryjvl's answer regarding the video card, though I'm not sure it fully explains the symptoms yet. This morning I ran a video stress test. The test itself ran fine, but immediately afterward the PC started acting up again. I left ProcExp open and various system processes were consuming 50-60% of the CPU but with no apparent reason. For example, "services.exe" was eating about 40%, but the sum of its child processes wasn't higher than about 5%. I left it alone for several minutes to settle down, and then it was fine again. I used the "video card stability test" from firestone-group.com. Its output isn't very detailed, but it at least exercises the hardware pretty hard. EDIT July 22 Thanks for your excellent suggestions. Here is an update on what I have tried so far. Ran memtest86, SeaTools (Seagate), Hitachi drive fitness test, video card stability test (mentioned above). The video card test was the only one that seemed to produce any results, though it didn't occur during the actual test. I defragged the drive (again...) with JkDefrag I dropped the video card

  Read the article

• Troubleshooting Website problems within the local network

  - by HaydnWVN

  Have an external website which opens fine on some PC's, yet seems to time out (or symptoms of timing out, but never actually does) on others. Seems to only affect (some) of our newer HP Pro 3305 MT Workstations. All of which are running Win7 32bit SP1 with all updates. Older PC's (Win7 32bit SP1 & WinXP) are unaffected. Using Google Chrome & Firefox makes no difference. Opening the website in IE9 Compatibility Mode has exactly the same symptoms. All PC's are on the same local network (Workgroup) using the same DNS server & gateway (inhouse) on the same internet connection, on the same subnet. There is no proxy server, no content filtering, no load balancing etc etc. Only group policy in effect (locally) is for Update scheduling. Local firewalls are all the same (Kaspersky WP4) and our external facing firewall has no IP specific settings. I have no control over the external website, traceroute shows the same destination on all PC's. It is a fairly popular website in our industry (Horticulture) and i'm not aware of any other people (even other sites within our sister companies) with the same problem. Update: Used Fiddler2 to monitor the HTTP request, seems its not getting fulfilled for some reason?! Request sent: GET http://www.rhs.org.uk/ HTTP/1.1 Host: www.rhs.org.uk Connection: keep-alive User-Agent: Mozilla/5.0 (Windows NT 6.1) AppleWebKit/536.11 (KHTML, like Gecko) Chrome/20.0.1132.47 Safari/536.11 Accept: text/html,application/xhtml+xml,application/xml;q=0.9,*/*;q=0.8 Accept-Encoding: gzip,deflate,sdch Accept-Language: en-GB,en-US;q=0.8,en;q=0.6 Accept-Charset: ISO-8859-1,utf-8;q=0.7,*;q=0.3 Log from Fiddler 2 of the request: This session is not yet complete. Press F5 to refresh when session is complete for updated statistics. Request Count: 1 Bytes Sent: 567 (headers:567; body:0) Bytes Received: 0 (headers:0; body:0) ACTUAL PERFORMANCE -------------- ClientConnected: 17:02:33.720 ClientBeginRequest: 17:02:39.118 GotRequestHeaders: 17:02:39.118 ClientDoneRequest: 17:02:39.118 Determine Gateway: 0ms DNS Lookup: 0ms TCP/IP Connect: 46ms HTTPS Handshake: 0ms ServerConnected: 17:02:39.165 FiddlerBeginRequest: 17:02:39.165 ServerGotRequest: 17:02:39.165 ServerBeginResponse: 00:00:00.000 GotResponseHeaders: 00:00:00.000 ServerDoneResponse: 00:00:00.000 ClientBeginResponse: 00:00:00.000 ClientDoneResponse: 00:00:00.000 RESPONSE BYTES (by Content-Type) -------------- ~headers~: 0 Log of a successful request from a working PC (done this morning, excuse the timestamps being different from above): Request Count: 1 Bytes Sent: 493 (headers:493; body:0) Bytes Received: 20,413 (headers:525; body:19,888) ACTUAL PERFORMANCE -------------- ClientConnected: 08:22:47.766 ClientBeginRequest: 08:22:47.766 GotRequestHeaders: 08:22:47.766 ClientDoneRequest: 08:22:47.766 Determine Gateway: 0ms DNS Lookup: 26ms TCP/IP Connect: 30ms HTTPS Handshake: 0ms ServerConnected: 08:22:47.828 FiddlerBeginRequest: 08:22:47.828 ServerGotRequest: 08:22:47.828 ServerBeginResponse: 08:22:48.905 GotResponseHeaders: 08:22:48.905 ServerDoneResponse: 08:22:48.905 ClientBeginResponse: 08:22:48.905 ClientDoneResponse: 08:22:48.905 Overall Elapsed: 00:00:01.1388020 RESPONSE BYTES (by Content-Type) -------------- text/html: 19,888 ~headers~: 525 So my question has evolved into: What is the difference between the 2 requests and how do I determine why 1 PC is not getting a reply to it's GET request?

  Read the article

• iptables - quick safety eval & limit max conns over time

  - by Peter Hanneman

  Working on locking down a *nix server box with some fancy iptable(v1.4.4) rules. I'm approaching the matter with a "paranoid, everyone's out to get me" style, not necessarily because I expect the box to be a hacker magnet but rather just for the sake of learning iptables and *nix security more throughly. Everything is well commented - so if anyone sees something I missed please let me know! The *nat table's "--to-ports" point to the only ports with actively listening services. (aside from pings) Layer 2 apps listen exclusively on chmod'ed sockets bridged by one of the layer 1 daemons. Layers 3+ inherit from layer 2 in a similar fashion. The two lines giving me grief are commented out at the very bottom of the *filter rules. The first line runs fine but it's all or nothing. :) Many thanks, Peter H. *nat #Flush previous rules, chains and counters for the 'nat' table -F -X -Z #Redirect traffic to alternate internal ports -I PREROUTING --src 0/0 -p tcp --dport 80 -j REDIRECT --to-ports 8080 -I PREROUTING --src 0/0 -p tcp --dport 443 -j REDIRECT --to-ports 8443 -I PREROUTING --src 0/0 -p udp --dport 53 -j REDIRECT --to-ports 8053 -I PREROUTING --src 0/0 -p tcp --dport 9022 -j REDIRECT --to-ports 8022 COMMIT *filter #Flush previous settings, chains and counters for the 'filter' table -F -X -Z #Set default behavior for all connections and protocols -P INPUT DROP -P OUTPUT DROP -A FORWARD -j DROP #Only accept loopback traffic originating from the local NIC -A INPUT -i lo -j ACCEPT -A INPUT ! -i lo -d 127.0.0.0/8 -j DROP #Accept all outgoing non-fragmented traffic having a valid state -A OUTPUT ! -f -m state --state NEW,RELATED,ESTABLISHED -j ACCEPT #Drop fragmented incoming packets (Not always malicious - acceptable for use now) -A INPUT -f -j DROP #Allow ping requests rate limited to one per second (burst ensures reliable results for high latency connections) -A INPUT -p icmp --icmp-type 8 -m limit --limit 1/sec --limit-burst 2 -j ACCEPT #Declaration of custom chains -N INSPECT_TCP_FLAGS -N INSPECT_STATE -N INSPECT #Drop incoming tcp connections with invalid tcp-flags -A INSPECT_TCP_FLAGS -p tcp --tcp-flags ALL ALL -j DROP -A INSPECT_TCP_FLAGS -p tcp --tcp-flags ALL NONE -j DROP -A INSPECT_TCP_FLAGS -p tcp --tcp-flags ACK,FIN FIN -j DROP -A INSPECT_TCP_FLAGS -p tcp --tcp-flags ACK,PSH PSH -j DROP -A INSPECT_TCP_FLAGS -p tcp --tcp-flags ACK,URG URG -j DROP -A INSPECT_TCP_FLAGS -p tcp --tcp-flags SYN,FIN SYN,FIN -j DROP -A INSPECT_TCP_FLAGS -p tcp --tcp-flags ALL FIN,PSH,URG -j DROP -A INSPECT_TCP_FLAGS -p tcp --tcp-flags FIN,RST FIN,RST -j DROP -A INSPECT_TCP_FLAGS -p tcp --tcp-flags SYN,RST SYN,RST -j DROP -A INSPECT_TCP_FLAGS -p tcp --tcp-flags ALL SYN,FIN,PSH,URG -j DROP -A INSPECT_TCP_FLAGS -p tcp --tcp-flags ALL SYN,RST,ACK,FIN,URG -j DROP #Accept incoming traffic having either an established or related state -A INSPECT_STATE -m state --state ESTABLISHED,RELATED -j ACCEPT #Drop new incoming tcp connections if they aren't SYN packets -A INSPECT_STATE -m state --state NEW -p tcp ! --syn -j DROP #Drop incoming traffic with invalid states -A INSPECT_STATE -m state --state INVALID -j DROP #INSPECT chain definition -A INSPECT -p tcp -j INSPECT_TCP_FLAGS -A INSPECT -j INSPECT_STATE #Route incoming traffic through the INSPECT chain -A INPUT -j INSPECT #Accept redirected HTTP traffic via HA reverse proxy -A INPUT -p tcp --dport 8080 -j ACCEPT #Accept redirected HTTPS traffic via STUNNEL SSH gateway (As well as tunneled HTTPS traffic destine for other services) -A INPUT -p tcp --dport 8443 -j ACCEPT #Accept redirected DNS traffic for NSD authoritative nameserver -A INPUT -p udp --dport 8053 -j ACCEPT #Accept redirected SSH traffic for OpenSSH server #Temp solution: -A INPUT -p tcp --dport 8022 -j ACCEPT #Ideal solution: #Limit new ssh connections to max 10 per 10 minutes while allowing an "unlimited" (or better reasonably limited?) number of established connections. #-A INPUT -p tcp --dport 8022 --state NEW,ESTABLISHED -m recent --set -j ACCEPT #-A INPUT -p tcp --dport 8022 --state NEW -m recent --update --seconds 600 --hitcount 11 -j DROP COMMIT *mangle #Flush previous rules, chains and counters in the 'mangle' table -F -X -Z COMMIT

  Read the article

• Bugzilla : No SASL mechanism found

  - by niteshsinha

  I am using Bugzilla on windows 7. I am using the unofficial Bugzilla installer. I followed the steps accordingly and gave valid credentials wherever required. I open Bugzilla and try to create a new account , but i get the following error. Software error: No SASL mechanism found at C:/Program Files/Bugzilla/perl/perl/site/lib/Authen/SASL.pm line 77 at C:/Program Files/Bugzilla/perl/perl/lib/Net/SMTP.pm line 143 i ran checksetup.pl and found that Authen::SASL and SMTP both are available on my machine. The output of checksetup.pl is as follows. * This is Bugzilla 3.6.3 on perl 5.10.1 * Running on Win7 Build 7600 Checking perl modules... Checking for CGI.pm (v3.33) ok: found v3.49 Checking for Digest-SHA (any) ok: found v5.48 Checking for TimeDate (v2.21) ok: found v2.24 Checking for DateTime (v0.28) ok: found v0.53 Checking for DateTime-TimeZone (v0.79) ok: found v1.10 Checking for DBI (v1.41) ok: found v1.609 Checking for Template-Toolkit (v2.22) ok: found v2.22 Checking for Email-Send (v2.16) ok: found v2.198 Checking for Email-MIME (v1.861) ok: found v1.903 Checking for Email-MIME-Encodings (v1.313) ok: found v1.313 Checking for Email-MIME-Modifier (v1.442) ok: found v1.903 Checking for URI (any) ok: found v1.52 Checking available perl DBD modules... Checking for DBD-Pg (v1.45) ok: found v2.16.1 Checking for DBD-mysql (v4.00) ok: found v4.012 Checking for DBD-Oracle (v1.19) not found The following Perl modules are optional: Checking for GD (v1.20) ok: found v2.44 Checking for Chart (v2.1) ok: found v2.4.1 Checking for Template-GD (any) ok: found v1.56 Checking for GDTextUtil (any) ok: found v0.86 Checking for GDGraph (any) ok: found v1.44 Checking for XML-Twig (any) ok: found v3.34 Checking for MIME-tools (v5.406) ok: found v5.427 Checking for libwww-perl (any) ok: found v5.834 Checking for PatchReader (v0.9.4) ok: found v0.9.5 Checking for perl-ldap (any) ok: found v0.39 Checking for Authen-SASL (any) ok: found v2.15 Checking for RadiusPerl (any) ok: found v0.17 Checking for SOAP-Lite (v0.710.06) ok: found v0.710.10 Checking for JSON-RPC (any) ok: found v0.95 Checking for Test-Taint (any) ok: found v1.04 Checking for HTML-Parser (v3.40) ok: found v3.64 Checking for HTML-Scrubber (any) ok: found v0.08 Checking for Email-MIME-Attachment-Stripper (any) ok: found v1.316 Checking for Email-Reply (any) ok: found v1.202 Checking for TheSchwartz (any) not found Checking for Daemon-Generic (any) not found Checking for mod_perl (v1.999022) not found *********************************************************************** * OPTIONAL MODULES * *********************************************************************** * Certain Perl modules are not required by Bugzilla, but by * * installing the latest version you gain access to additional * * features. * * * * The optional modules you do not have installed are listed below, * * with the name of the feature they enable. Below that table are the * * commands to install each module. * *********************************************************************** * MODULE NAME * ENABLES FEATURE(S) * *********************************************************************** * TheSchwartz * Mail Queueing * * Daemon-Generic * Mail Queueing * * mod_perl * mod_perl * *********************************************************************** * Note For Windows Users * *********************************************************************** * In order to install the modules listed below, you first have to run * * the following command as an Administrator: * * * * ppm repo add theory58S http://cpan.uwinnipeg.ca/PPMPackages/10xx/ * * * Then you have to do (also as an Administrator): * * * * ppm repo up theory58S * * * * Do that last command over and over until you see "theory58S" at the * * top of the displayed list. * *********************************************************************** COMMANDS TO INSTALL OPTIONAL MODULES: TheSchwartz: ppm install TheSchwartz Daemon-Generic: ppm install Daemon-Generic mod_perl: ppm install mod_perl Reading ./localconfig... Checking for DBD-mysql (v4.00) ok: found v4.012 Checking for MySQL (v4.1.2) ok: found v5.1.44-community-log Removing existing compiled templates... Precompiling templates...done. Now that you have installed Bugzilla, you should visit the 'Parameters' page (linked in the footer of the Administrator account) to ensure it is set up as you wish - this includes setting the 'urlbase' option to the correct URL. Press any key to continue . . . Please tell me what should i do. Please note: i am running behind a corporate proxy , SSL/TLS is not used internally but i am giving the smtpUser and smtpPass also.

  Read the article

• unattended-upgrades does not reboot

  - by Cheiron

  I am running Debian 7 stable with unattended-upgrades (every morning at 6 AM) to make sure I am always fully updated. I have the following config: $ cat /etc/apt/apt.conf.d/50unattended-upgrades // Automatically upgrade packages from these origin patterns Unattended-Upgrade::Origins-Pattern { // Archive or Suite based matching: // Note that this will silently match a different release after // migration to the specified archive (e.g. testing becomes the // new stable). "o=Debian,a=stable"; "o=Debian,a=stable-updates"; // "o=Debian,a=proposed-updates"; "origin=Debian,archive=stable,label=Debian-Security"; }; // List of packages to not update Unattended-Upgrade::Package-Blacklist { // "vim"; // "libc6"; // "libc6-dev"; // "libc6-i686"; }; // This option allows you to control if on a unclean dpkg exit // unattended-upgrades will automatically run // dpkg --force-confold --configure -a // The default is true, to ensure updates keep getting installed //Unattended-Upgrade::AutoFixInterruptedDpkg "false"; // Split the upgrade into the smallest possible chunks so that // they can be interrupted with SIGUSR1. This makes the upgrade // a bit slower but it has the benefit that shutdown while a upgrade // is running is possible (with a small delay) //Unattended-Upgrade::MinimalSteps "true"; // Install all unattended-upgrades when the machine is shuting down // instead of doing it in the background while the machine is running // This will (obviously) make shutdown slower //Unattended-Upgrade::InstallOnShutdown "true"; // Send email to this address for problems or packages upgrades // If empty or unset then no email is sent, make sure that you // have a working mail setup on your system. A package that provides // 'mailx' must be installed. E.g. "[email protected]" Unattended-Upgrade::Mail "root"; // Set this value to "true" to get emails only on errors. Default // is to always send a mail if Unattended-Upgrade::Mail is set Unattended-Upgrade::MailOnlyOnError "true"; // Do automatic removal of new unused dependencies after the upgrade // (equivalent to apt-get autoremove) //Unattended-Upgrade::Remove-Unused-Dependencies "false"; // Automatically reboot *WITHOUT CONFIRMATION* if a // the file /var/run/reboot-required is found after the upgrade Unattended-Upgrade::Automatic-Reboot "true"; // Use apt bandwidth limit feature, this example limits the download // speed to 70kb/sec //Acquire::http::Dl-Limit "70"; As you can see Automatic-Reboot is true and thus the server should automaticly reboot. Last time I checked the server was online for over 100 days, which means that the update from Debian 7.1 to Debian 7.2 has happened while the server was up (and indeed, all updates were installed), but this involves kernel updates, which means that the server should reboot. It did not. The server was running very slow, so I rebooted which fixed that. I did some research and found out that unattended-upgrades responds to the reboot-required file in /var/run/. I touched this file and waited one week, the file still exists and the server did not reboot. So I think that unattended-uppgrades ignores the auto-reboot part. So, am I doing somthing wrong here? Why did the server not restart? The upgrade part works perfect by the way, its just the reboot part that does not seem to work as it should.

  Read the article

• pptpd not working externally on Ubuntu Server 11.10

  - by Brendan

  I am trying to set up a pptpd vpn on our newly installed Ubuntu 11.10 64 bit server, but am not having success having a client connect via an iPhone to the VPN. Note that no clients have been able to connect to this VPN from outside of the network. The system is up to date with patches. Here is the output of /var/log/syslog. Please note that 222.153.x.y is my remote IP address. Mar 30 22:07:47 server pptpd[9546]: CTRL: Client 222.153.x.y control connection started Mar 30 22:07:47 server pptpd[9546]: CTRL: Starting call (launching pppd, opening GRE) Mar 30 22:07:47 server pppd[9555]: Plugin /usr/lib/pptpd/pptpd-logwtmp.so loaded. Mar 30 22:07:47 server pppd[9555]: pppd 2.4.5 started by root, uid 0 Mar 30 22:07:47 server pppd[9555]: Using interface ppp0 Mar 30 22:07:47 server pppd[9555]: Connect: ppp0 <--> /dev/pts/3 Mar 30 22:07:47 server pptpd[9546]: GRE: Bad checksum from pppd. Mar 30 22:08:17 server pppd[9555]: LCP: timeout sending Config-Requests Mar 30 22:08:17 server pppd[9555]: Connection terminated. Mar 30 22:08:17 server pppd[9555]: Modem hangup Mar 30 22:08:17 server pppd[9555]: Exit. Mar 30 22:08:17 server pptpd[9546]: GRE: read(fd=6,buffer=6075a0,len=8196) from PTY failed: status = -1 error = Input/output error, usually caused by unexpected termination of pppd, check option syntax and pppd logs Mar 30 22:08:17 server pptpd[9546]: CTRL: PTY read or GRE write failed (pty,gre)=(6,7) Mar 30 22:08:17 server pptpd[9546]: CTRL: Reaping child PPP[9555] Mar 30 22:08:17 server pptpd[9546]: CTRL: Client 222.153.x.y control connection finished As you can see, the problem seems to be the connection timing out after 30 seconds ("Mar 30 22:08:17 server pppd[9555]: LCP: timeout sending Config-Requests". Over Wifi however (inside the local network) there are no issues: Mar 30 22:12:33 unreal-server pptpd[12406]: CTRL: Client 192.168.0.100 control connection started Mar 30 22:12:33 unreal-server pptpd[12406]: CTRL: Starting call (launching pppd, opening GRE) Mar 30 22:12:33 unreal-server pppd[12407]: Plugin /usr/lib/pptpd/pptpd-logwtmp.so loaded. Mar 30 22:12:33 unreal-server pppd[12407]: pppd 2.4.5 started by root, uid 0 Mar 30 22:12:33 unreal-server pppd[12407]: Using interface ppp0 Mar 30 22:12:33 unreal-server pppd[12407]: Connect: ppp0 <--> /dev/pts/3 Mar 30 22:12:33 unreal-server pptpd[12406]: GRE: Bad checksum from pppd. Mar 30 22:12:36 unreal-server pppd[12407]: peer from calling number 192.168.0.100 authorized Mar 30 22:12:36 unreal-server pppd[12407]: MPPE 128-bit stateless compression enabled Mar 30 22:12:36 unreal-server pppd[12407]: Cannot determine ethernet address for proxy ARP Mar 30 22:12:36 unreal-server pppd[12407]: local IP address 192.168.0.10 Mar 30 22:12:36 unreal-server pppd[12407]: remote IP address 192.168.1.1 I have set up an iptables config for the server; to check this isn't the problem I allowed all traffic temporarily, but this does NOT change the symptoms in the first example. Here is the output from /etc/iptables.rules.save *filter :FORWARD ACCEPT [0:0] :INPUT ACCEPT [0:0] :OUTPUT ACCEPT [0:0] COMMIT Even with these rules applied, the output from /var/log/syslog is LINE FOR LINE what I saw in the the first block of code. Please note that before running this Ubuntu server; an old SME Server box was running in place of it, that had a pptpd server on it just like we are using, and we experienced no issues.

  Read the article

• ASA 5505 stops local internet when connected to VPN

  - by g18c

  Hi I have a Cisco ASA router running firmware 8.2(5) which hosts an internal LAN on 192.168.30.0/24. I have used the VPN Wizard to setup L2TP access and I can connect in fine from a Windows box and can ping hosts behind the VPN router. However, when connected to the VPN I can no longer ping out to my internet or browse web pages. I would like to be able to access the VPN, and also browse the internet at the same time - I understand this is called split tunneling (have ticked the setting in the wizard but to no effect) and if so how do I do this? Alternatively, if split tunneling is a pain to setup, then making the connected VPN client have internet access from the ASA WAN IP would be OK. Thanks, Chris names ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Vlan1 nameif inside security-level 100 ip address 192.168.30.1 255.255.255.0 ! interface Vlan2 nameif outside security-level 0 ip address 208.74.158.58 255.255.255.252 ! ftp mode passive access-list inside_nat0_outbound extended permit ip any 10.10.10.0 255.255.255.128 access-list inside_nat0_outbound extended permit ip 192.168.30.0 255.255.255.0 192.168.30.192 255.255.255.192 access-list DefaultRAGroup_splitTunnelAcl standard permit 192.168.30.0 255.255.255.0 access-list DefaultRAGroup_splitTunnelAcl_1 standard permit 192.168.30.0 255.255.255.0 pager lines 24 logging asdm informational mtu inside 1500 mtu outside 1500 ip local pool LANVPNPOOL 192.168.30.220-192.168.30.249 mask 255.255.255.0 icmp unreachable rate-limit 1 burst-size 1 no asdm history enable arp timeout 14400 global (outside) 1 interface nat (inside) 0 access-list inside_nat0_outbound nat (inside) 1 192.168.30.0 255.255.255.0 route outside 0.0.0.0 0.0.0.0 208.74.158.57 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 timeout floating-conn 0:00:00 dynamic-access-policy-record DfltAccessPolicy http server enable http 192.168.30.0 255.255.255.0 inside snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac crypto ipsec transform-set TRANS_ESP_3DES_SHA esp-3des esp-sha-hmac crypto ipsec transform-set TRANS_ESP_3DES_SHA mode transport crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5 TRANS_ESP_3DES_SHA crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP crypto map outside_map interface outside crypto isakmp enable outside crypto isakmp policy 10 authentication pre-share encryption 3des hash sha group 2 lifetime 86400 telnet timeout 5 ssh timeout 5 console timeout 0 dhcpd auto_config outside ! threat-detection basic-threat threat-detection statistics access-list no threat-detection statistics tcp-intercept webvpn group-policy DefaultRAGroup internal group-policy DefaultRAGroup attributes dns-server value 192.168.30.3 vpn-tunnel-protocol l2tp-ipsec split-tunnel-policy tunnelspecified split-tunnel-network-list value DefaultRAGroup_splitTunnelAcl_1 username user password Cj7W5X7wERleAewO8ENYtg== nt-encrypted privilege 0 tunnel-group DefaultRAGroup general-attributes address-pool LANVPNPOOL default-group-policy DefaultRAGroup tunnel-group DefaultRAGroup ipsec-attributes pre-shared-key ***** tunnel-group DefaultRAGroup ppp-attributes no authentication chap authentication ms-chap-v2 ! class-map inspection_default match default-inspection-traffic ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum client auto message-length maximum 512 policy-map global_policy class inspection_default inspect dns preset_dns_map inspect ftp inspect h323 h225 inspect h323 ras inspect rsh inspect rtsp inspect esmtp inspect sqlnet inspect skinny inspect sunrpc inspect xdmcp inspect sip inspect netbios inspect tftp inspect ip-options ! service-policy global_policy global prompt hostname context : end

  Read the article

• Nginx - Redirect any Subdomain to File without Rewriting

  - by Waffle

  Recently I have switched from Apache to Nginx to increase performance on a web server running Ubuntu 11.10. I have been having issues trying to figure out how certain things work in Nginx compared to Apache, but one issue has been stumping me and I have not been able to find the answer online. My problem is that I need to be able to redirect (not rewrite) any sub-domain to a file, but that file needs to be able to get the sub-domain part of the URL in order to do a database look-up of that sub-domain. So far, I have been able to get any sub-domain to rewrite to that file, but then it loses the text of the sub-domain I need. So, for example, I would like test.server.com to redirect to server.com/resolve.php, but still remain as test.server.com. If this is not possible, the thing that I would need at the very least would be something such as going to test.server.com would go to server.com/resolve.php?=test . One of these options must be possible in Nginx. My config as it stands right now looks something like this: server { listen 80; ## listen for ipv4; this line is default and implied listen [::]:80 default ipv6only=on; ## listen for ipv6 root /usr/share/nginx/www; index index.php index.html index.htm; # Make site accessible from http://localhost/ server_name www.server.com server.com; location / { # First attempt to serve request as file, then # as directory, then fall back to index.html try_files $uri $uri/ /index.html; } location /doc { root /usr/share; autoindex on; allow 127.0.0.1; } location /images { root /usr/share; autoindex off; } #error_page 404 /404.html; # redirect server error pages to the static page /50x.html # #error_page 500 502 503 504 /50x.html; #location = /50x.html { # root /usr/share/nginx/www; #} # proxy the PHP scripts to Apache listening on 127.0.0.1:80 # #location ~ \.php$ { # proxy_pass http://127.0.0.1; #} # pass the PHP scripts to FastCGI server listening on 127.0.0.1:9000 # location ~ \.php$ { fastcgi_pass unix:/tmp/php5-fpm.sock; fastcgi_index index.php; include fastcgi_params; } # deny access to .htaccess files, if Apache's document root # concurs with nginx's one # #location ~ /\.ht { # deny all; #} } server { listen 80 default; server_name *.server.com; rewrite ^ http://www.server.com/resolve.php; } As I said before, I am very new to Nginx, so I have a feeling the answer is pretty simple, but no examples online seem to deal with just redirects without rewrites or rewriting with the sub-domain section included. Any help on what to do would be most appreciated and if any one has a better idea to accomplish what I need, I am also open to ideas. Thank you very much.

  Read the article

• what is best config for nginx worker_rlimit_nofile and worker_connections 28672

  - by Binh Nguyen

  i have issue of web-brower response ( especially on ie ) very slow, some time time out, and sometime hang out up to 20 seconds for one file redirect 301 when test with "f12 derverloper tool of ie" .. it report wait/start time very long. but after got connected the elements on web weill be dowload and show out fast ( test at xaluan.com ) It most happen when active user on web more than 2100 ( use google real time live analytic ). server running cenos 5 with ngix, apache, 32core cpu, 96G ram, raid 10 sas hdd.. == flowing is my config == user nobody; # no need for more workers in the proxy mode worker_processes 28; #old 32 #good at 24 error_log /var/log/nginx/error.log; #old add in end: info worker_rlimit_nofile 22528; events { worker_connections 22528; use epoll; # you should use epoll here for Linux kernels 2.6.x } http { server_name_in_redirect off; server_names_hash_max_size 10240; server_names_hash_bucket_size 1024; include mime.types; default_type application/octet-stream; server_tokens off; disable_symlinks off; sendfile on; tcp_nopush on; tcp_nodelay on; server_name_in_redirect off; server_names_hash_max_size 10240; server_names_hash_bucket_size 1024; include mime.types; default_type application/octet-stream; server_tokens off; disable_symlinks off; sendfile on; tcp_nopush on; tcp_nodelay on; keepalive_timeout 25; #old 5 gzip on; #old on gzip_vary on; gzip_disable "MSIE [1-6]\."; gzip_proxied any; gzip_http_version 1.1; gzip_min_length 1000; gzip_comp_level 6; gzip_buffers 16 8k; ignore_invalid_headers on; client_header_timeout 1m; #3m client_body_timeout 1m; #3m send_timeout 1m; #3m reset_timedout_connection on; connection_pool_size 256; client_header_buffer_size 256k; large_client_header_buffers 4 256k; client_max_body_size 100M; client_body_buffer_size 256k; request_pool_size 32k; output_buffers 4 32k; postpone_output 1460; proxy_temp_path /tmp/nginx_proxy/; client_body_in_file_only on; log_format bytes_log "$msec $bytes_sent ."; limit_conn_zone $binary_remote_addr zone=limit_per_ip:1m; limit_conn limit_per_ip 20; limit_req_zone $binary_remote_addr zone=allips:5m rate=200r/s; limit_req zone=allips burst=200 nodelay; include "/etc/nginx/vhosts/*"; } =========== I have play around with worker config 1- tried increase as some one suggess: worker_rlimit_nofile = worker_connections = worker_processes * 1024 = 32768 2- tried to set low: worker_processes = 28 and other worker at 22582 and other solution too .. but not work cause some time it make server load hight very quick 3- tried to comment out the # worker_rlimit_nofile . so it will be unlimited. it look like solved a bit about issue response time. but it also make server high load quick in peak time... Please help thanks PS: other apache you may have look for help me out thanks Listen 0.0.0.0:8081 User nobody Group nobody ExtendedStatus On ServerAdmin [email protected] ServerName server.xaluan.com LogLevel warn # These can be set in WHM under 'Apache Global Configuration' Timeout 100 TraceEnable Off ServerSignature Off ServerTokens ProductOnly FileETag None StartServers 15 <IfModule prefork.c> MinSpareServers 20 MaxSpareServers 50 #MaxSpareServers 40 </IfModule> ServerLimit 1572 MaxClients 1572 MaxRequestsPerChild 4000 # MaxRequestsPerChild 3000 KeepAlive On KeepAliveTimeout 3 MaxKeepAliveRequests 300 #MaxKeepAliveRequests 130

  Read the article

• phpMyAdmin setup issues

  - by EquinoX

  I am trying to follow the tutorial here to setup the user and pass. It says there that "this section is only applicable if your MySQL server is running with --skip-show-database". First question is, how do I check if MySQl server is running with --skip-show-database? Is there any way I can access phpMyAdmin SQL query window without logging in? Otherwise I'd have to execute this SQL from command line. I am also getting this: Cannot load mcrypt extension. Please check your PHP configuration. I have added mcrypt.so to php.ini and doing the following command proves that I have it. [root@DT html]# rpm -qa | grep mcrypt mcrypt-2.6.8-1.el5 php-mcrypt-5.3.5-1.1.w5 libmcrypt-2.5.8-4.el5.centos [root@DT html]# php -v PHP 5.3.5 (cli) (built: Feb 19 2011 13:10:09) Copyright (c) 1997-2010 The PHP Group Zend Engine v2.3.0, Copyright (c) 1998-2010 Zend Technologies Now when I go to phpinfo() and search for mcrypt it can find it inside the Configure Command row ('--with-mcrypt=shared,/usr'). So, what to do next?. UPDATE: I didn't put extension=mcrypt.so in php.ini as it will complain the following: PHP Warning: Module 'mcrypt' already loaded in Unknown on line 0 Here's my nginx.conf: #user nobody; worker_processes 2; #error_log logs/error.log; #error_log logs/error.log notice; #error_log logs/error.log info; #pid logs/nginx.pid; events { worker_connections 1024; } http { include mime.types; default_type application/octet-stream; #log_format main '$remote_addr - $remote_user [$time_local] "$request" ' # '$status $body_bytes_sent "$http_referer" ' # '"$http_user_agent" "$http_x_forwarded_for"'; #access_log logs/access.log main; sendfile on; #tcp_nopush on; #keepalive_timeout 0; keepalive_timeout 65; gzip on; server { listen 80; root /usr/share/nginx/html; server_name localhost; #charset koi8-r; #access_log logs/host.access.log main; location / { #root html; index index.html index.htm; } #error_page 404 /404.html; # redirect server error pages to the static page /50x.html # error_page 500 502 503 504 /50x.html; location = /50x.html { #root html; } # proxy the PHP scripts to Apache listening on 127.0.0.1:80 # #location ~ \.php$ { # proxy_pass http://127.0.0.1; #} # pass the PHP scripts to FastCGI server listening on 127.0.0.1:9000 # location ~ \.php$ { #root /usr/local/nginx/html; fastcgi_pass 127.0.0.1:9000; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME /usr/share/nginx/html$fastcgi_script _name; include fastcgi_params; } # deny access to .htaccess files, if Apache's document root # concurs with nginx's one location ~ /\.ht { deny all; } } # another virtual host using mix of IP-, name-, and port-based configuration # #server { # listen 8000; # listen somename:8080; # server_name somename alias another.alias; # location / { # root html; # index index.html index.htm; # } #} # HTTPS server # #server { # listen 443; # server_name localhost; # ssl on; # ssl_certificate cert.pem; # ssl_certificate_key cert.key; # ssl_session_timeout 5m; # ssl_protocols SSLv2 SSLv3 TLSv1; # ssl_ciphers ALL:!ADH:!EXPORT56:RC4+RSA:+HIGH:+MEDIUM:+LOW:+SSLv2:+EXP; # ssl_prefer_server_ciphers on; # location / { # root html; # index index.html index.htm; # } #} }

  Read the article

• why is my centos, nginx, php,mysql server using so much memory

  - by kb2tfa

  i'm not sure where the problem lies. I have: centos 6 mysql php php-fpm wordpress (1 site). this is a dedicated server i'm learning on. as soon as i ran the web url the memory slammed to 125% of a 512k server, i had to upgrade to 1gig, so i'm not sure where the problem lies. I thought by switching to nginx from apache i would have more memory free, but i'm still stuck with the problem. before launching the site with nginx and mysqld running the site was about 5% memory. I reanamed my "my-small.cnf" to my.cnf and put in my /etc folder where the original was, but that seems not to have done it. after looking at my TOP results, i'm starting to think it may be php-fpm eating my memory, but not sure. is php-fpm the preferend way or is there something better to use. I read about possible memory leaks in php-fpm. here is what i have: php-fpm.conf ;;;;;;;;;;;;;;;;;;;;; ; FPM Configuration ; ;;;;;;;;;;;;;;;;;;;;; ; All relative paths in this configuration file are relative to PHP's install ; prefix. ; Include one or more files. If glob(3) exists, it is used to include a bunch of ; files from a glob(3) pattern. This directive can be used everywhere in the ; file. include=/etc/php-fpm.d/*.conf ;;;;;;;;;;;;;;;;;; ; Global Options ; ;;;;;;;;;;;;;;;;;; [global] ; Pid file ; Default Value: none pid = /var/run/php-fpm/php-fpm.pid ; Error log file ; Default Value: /var/log/php-fpm.log error_log = /var/log/php-fpm/error.log ; Log level ; Possible Values: alert, error, warning, notice, debug ; Default Value: notice ;log_level = notice ; If this number of child processes exit with SIGSEGV or SIGBUS within the time ; interval set by emergency_restart_interval then FPM will restart. A value ; of '0' means 'Off'. ; Default Value: 0 ;emergency_restart_threshold = 0 ; Interval of time used by emergency_restart_interval to determine when ; a graceful restart will be initiated. This can be useful to work around ; accidental corruptions in an accelerator's shared memory. ; Available Units: s(econds), m(inutes), h(ours), or d(ays) ; Default Unit: seconds ; Default Value: 0 ;emergency_restart_interval = 0 ; Time limit for child processes to wait for a reaction on signals from master. ; Available units: s(econds), m(inutes), h(ours), or d(ays) ; Default Unit: seconds ; Default Value: 0 ;process_control_timeout = 0 ; Send FPM to background. Set to 'no' to keep FPM in foreground for debugging. ; Default Value: yes ;daemonize = yes ;;;;;;;;;;;;;;;;;;;; ; Pool Definitions ; ;;;;;;;;;;;;;;;;;;;; ; See /etc/php-fpm.d/*.conf end php-fpm.conf

  Read the article

• Issue in nginx proxying to apache

  - by Luis Masuelli

  My current nginx configuration is as follows: specific configuration for (currently two) domains: server { listen 443 ssl; server_name studiotv.service.tebusco.lan phpmyadmin.service.tebusco.lan; ssl_certificate /home/administrador/nginx-confs/ssl/service.tebusco.lan.crt; ssl_certificate_key /home/administrador/nginx-confs/ssl/service.tebusco.lan.key; location / { proxy_pass http://127.0.0.1:8180; proxy_set_header Host $http_host:8180; } } default configuration for unmatched ssl connections: server { listen 443 default ssl; ssl_certificate /home/administrador/nginx-confs/ssl/service.tebusco.lan.crt; ssl_certificate_key /home/administrador/nginx-confs/ssl/service.tebusco.lan.key; location / { return 403; } } http configuration: server { listen 80; rewrite ^ https://$host$request_uri? permanent; } The intention is clear: Redirect http traffic to https. Proxy each https:// call from phpmyadmin.service.tebusco.lan and studiotv.service.tebusco.lan to apache2. This includes passing a host header, which is detected. Each unmatched ssl connection must return a 403 in nginx. Does not even reach apache2. In the apache2 side of the life, I have a default site, and a non-default site which will match studiotv.service.tebusco.lan: 000-default.conf file (available and enabled): <VirtualHost 127.0.0.1:8180> # The ServerName directive sets the request scheme, hostname and port that # the server uses to identify itself. This is used when creating # redirection URLs. In the context of virtual hosts, the ServerName # specifies what hostname must appear in the request's Host: header to # match this virtual host. For the default virtual host (this file) this # value is not decisive as it is used as a last resort host regardless. # However, you must set it for any further virtual host explicitly. ServerName localhost ServerAdmin webmaster@localhost DocumentRoot /var/www/html <Directory /var/www/html> Order deny,allow Require all granted </Directory> </VirtualHost> # vim: syntax=apache ts=4 sw=4 sts=4 sr noet studiotv.conf file (available and enabled): <VirtualHost *:8180> ServerName studiotv.service.tebusco.lan ServerAdmin [email protected] DocumentRoot /var/www/studiotv <Directory /var/www/studiotv/> Options -Indexes +FollowSymLinks AllowOverride None Order deny,allow Allow from all Require all granted </Directory> # Available loglevels: trace8, ..., trace1, debug, info, notice, warn, # error, crit, alert, emerg. # It is also possible to configure the loglevel for particular # modules, e.g. #LogLevel info ssl:warn # No usamos ${APACHE_LOG_DIR} sino en su lugar /var/log/<host> ErrorLog /var/log/apache2/studiotv/error.log CustomLog /var/log/apache2/studiotv/access.log combined </VirtualHost> # vim: syntax=apache ts=4 sw=4 sts=4 sr noet However, when I hit the browser with http://studiotv.service.tebusco.lan, the default php page is shown instead. Question: What am I missing? (apache 2.4.7, nginx 1.6.0, ubuntu server 14.04).

  Read the article

• suddenly can't connect to router

  - by Khoi

  I was just downloading some stuff in ubuntu and snap, the connection cut and I can't even connect to my router. And the router, it still works fine, my laptop can connect wirelessly to it as usual. But my main computer (which connects to it directly through cable) can't even ping it. Here is my ipconfig: Windows IP Configuration Host Name . . . . . . . . . . . . : vento Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Unknown IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No Ethernet adapter Local Area Connection: Media State . . . . . . . . . . . : Media disconnected Description . . . . . . . . . . . : Realtek RTL8169/8110 Family Gigabit Ethernet NIC Physical Address. . . . . . . . . : 00-19-DB-4E-6C-56 Ethernet adapter {15B1F740-2F35-4FE4-9FEE-4052AFBAD096}: Media State . . . . . . . . . . . : Media disconnected Description . . . . . . . . . . . : Anchorfree HSS Adapter - Packet Sche duler Miniport Physical Address. . . . . . . . . : 00-FF-15-B1-F7-40

  Read the article

• EXTJS 3.2.1 EditorGridPanel - ComboBox with jsonstore

  - by Yoong Kim

  Hi, I am using EXTJS with an editorgridpanel and I am trying to to insert a combobox, populated with JsonStore. Here is a snapshot of my code: THE STORE: kmxgz.ordercmpappro.prototype.getCmpapproStore = function(my_url) { var myStore = new Ext.data.Store({ proxy: new Ext.data.HttpProxy({ url: my_url , method: 'POST' }) , reader: new Ext.data.JsonReader({ root: 'rows', totalProperty: 'total', id: 'list_cmpappro_id', fields: [ {name: 'list_cmpappro_id', mapping: 'list_cmpappro_id'} , {name: 'list_cmpappro_name', mapping: 'list_cmpappro_name'} ] }) , autoLoad: true , id: 'cmpapproStore' , listeners: { load: function(store, records, options){ //store is loaded, now you can work with it's records, etc. console.info('store load, arguments:', arguments); console.info('Store count = ', store.getCount()); } } }); return myStore; }; THE COMBO: kmxgz.ordercmpappro.prototype.getCmpapproCombo = function(my_store) { var myCombo = new Ext.form.ComboBox({ typeAhead: true, lazyRender:false, forceSelection: true, allowBlank: true, editable: true, selectOnFocus: true, id: 'cmpapproCombo', triggerAction: 'all', fieldLabel: 'CMP Appro', valueField: 'list_cmpappro_id', displayField: 'list_cmpappro_name', hiddenName: 'cmpappro_id', valueNotFoundText: 'Value not found.', mode: 'local', store: my_store, emptyText: 'Select a CMP Appro', loadingText: 'Veuillez patienter ...', listeners: { // 'change' will be fired when the value has changed and the user exits the ComboBox via tab, click, etc. // The 'newValue' and 'oldValue' params will be from the field specified in the 'valueField' config above. change: function(combo, newValue, oldValue){ console.log("Old Value: " + oldValue); console.log("New Value: " + newValue); }, // 'select' will be fired as soon as an item in the ComboBox is selected with mouse, keyboard. select: function(combo, record, index){ console.log(record.data.name); console.log(index); } } }); return myCombo; }; The combobox is inserted in an editorgridpanel. There's a renderer like this: Ext.util.Format.comboRenderer = function(combo){ return function(value, metadata, record){ alert(combo.store.getCount()); <== always 0!! var record = combo.findRecord(combo.valueField || combo.displayField, value); return record ? record.get(combo.displayField) : combo.valueNotFoundText; } }; When the grid is displayed the first time, instead of have the displayField, I have : "Value not found." And I have the alert : 0 (alert(combo.store.getCount())) from the renderer. But I can see in the console that the data have been correctly loaded! Even if I try to reload the store from the renderer (combo.store.load();), I still have the alert (0)! But when I select the combo to change the value, I can see the data and when I change the value, I can see the displayFiel! I don't understand what's the problem? Since now several days, I already tried all the solutions I found...but still nothing! Any advice is welcome! Yoong

  Read the article

• How to convert a DataSet object into an ObjectContext (Entity Framework) object on the fly?

  - by Marcel

  Hi all, I have an existing SQL Server database, where I store data from large specific log files (often 100 MB and more), one per database. After some analysis, the database is deleted again. From the database, I have created both a Entity Framework Model and a DataSet Model via the Visual Studio designers. The DataSet is only for bulk importing data with SqlBulkCopy, after a quite complicated parsing process. All queries are then done using the Entity Framework Model, whose CreateQuery Method is exposed via an interface like this public IQueryable<TTarget> GetResults<TTarget>() where TTarget : EntityObject, new() { return this.Context.CreateQuery<TTarget>(typeof(TTarget).Name); } Now, sometimes my files are very small and in such a case I would like to omit the import into the database, but just have a an in-memory representation of the data, accessible as Entities. The idea is to create the DataSet, but instead of bulk importing, to directly transfer it into an ObjectContext which is accessible via the interface. Does this make sense? Now here's what I have done for this conversion so far: I traverse all tables in the DataSet, convert the single rows into entities of the corresponding type and add them to instantiated object of my typed Entity context class, like so MyEntities context = new MyEntities(); //create new in-memory context ///.... //get the item in the navigations table MyDataSet.NavigationResultRow dataRow = ds.NavigationResult.First(); //here, a foreach would be necessary in a true-world scenario NavigationResult entity = new NavigationResult { Direction = dataRow.Direction, ///... NavigationResultID = dataRow.NavigationResultID }; //convert to entities context.AddToNavigationResult(entity); //add to entities ///.... A very tedious work, as I would need to create a converter for each of my entity type and iterate over each table in the DataSet I have. Beware, if I ever change my database model.... Also, I have found out, that I can only instantiate MyEntities, if I provide a valid connection string to a SQL Server database. Since I do not want to actually write to my fully fledged database each time, this hinders my intentions. I intend to have only some in-memory proxy database. Can I do simpler? Is there some automated way of doing such a conversion, like generating an ObjectContext out of a DataSet object? P.S: I have seen a few questions about unit testing that seem somewhat related, but not quite exact.

  Read the article

• WCF configuration for WebHttpBinding(Restful) for supporting both HTTP and HTTPS

  - by KSS

  We are using AJAX Cascading dropdown and AutoComplete functionality with Restful WebService Services providing data. With one endpoint(non-secured) eveything was working fine, until we tried same web page with https. Our Webappplication needs to support both. Our of very few articiles/blogs on this issue I found 2 which applies to my requirements. 1. http://blog.abstractlabs.net/2009/02/ajax-wcf-services-and-httphttps.html 2. _http://www.mydotnetworld.com/post/2008/10/18/Use-a-WCF-Service-with-HTTP-and-HTTPS-in-C.aspx I followed same pattern, added 2 endpoints, assuming WCF will pickup appropriate endpoint looking at HTTP or HTTPS protocol. Worked like a charm in my dev machine(XP-IIS5) and 1 Server 2003R2(IIS6), however did work in Production server 2003-IIS6. Website in IIS is exact same(including permission etc). The error it throws - Error 500(Could not find a base address that matches scheme https for the endpoint with binding WebHttpBinding. Registered base address schemes are [http]..) Here's the sample configuration(ignore typos) <system.serviceModel> <bindings> <webHttpBinding> <binding name="SecureBinding"> <security mode="Transport"/> </binding> </webHttpBinding> </bindings> <behaviors> <endpointBehaviors> <behavior name="SearchServiceAspNetAjaxBehavior"> <enableWebScript /> </behavior> </endpointBehaviors> </behaviors> <serviceHostingEnvironment aspNetCompatibilityEnabled="true" /> <services> <service name="SearchService"> <endpoint address="" behaviorConfiguration="SearchServiceAspNetAjaxBehavior" binding="webHttpBinding" contract="SearchServiceContract" /> <endpoint address="" behaviorConfiguration="SearchServiceAspNetAjaxBehavior" binding="webHttpBinding" bindingConfiguration="SecureBinding" contract="SearchServiceContract" /> </service> </services> </system.serviceModel> Any help on this is highly appreciated ? Thanks KSS

  Read the article

< Previous Page | 355 356 357 358 359 360 361 362 363 364 365 366  | Next Page >