Search Results

Search found 9688 results on 388 pages for 'external hdd'.

Page 361/388 | < Previous Page | 357 358 359 360 361 362 363 364 365 366 367 368  | Next Page >

  • Best Processor for MediaSmart Server?

    - by Kent Boogaart
    I'm trying to figure out what the best possible processor is that I can stick in my HP MediaSmart server. I'm clueless when it comes to correlating CPUs to motherboards. I suspect it's the socket type I care about, but I worry that there's more to it. CPU-Z gives me (excerpt): Processors Information ------------------------------------------------------------------------- Processor 1 ID = 0 Number of cores 1 (max 1) Number of threads 1 (max 1) Name AMD Sempron LE-1150 Codename Sparta Specification AMD Sempron(tm) Processor LE-1150 Package Socket AM2 (940) CPUID F.F.1 Extended CPUID F.7F Brand ID 1 Core Stepping DH-G1 Technology 65 nm Core Speed 1000.0 MHz Multiplier x FSB 5.0 x 200.0 MHz HT Link speed 800.0 MHz Stock frequency 2000 MHz Instructions sets MMX (+), 3DNow! (+), SSE, SSE2, SSE3, x86-64 L1 Data cache 64 KBytes, 2-way set associative, 64-byte line size L1 Instruction cache 64 KBytes, 2-way set associative, 64-byte line size L2 cache 256 KBytes, 16-way set associative, 64-byte line size FID/VID Control yes Max FID 10.0x Max VID 1.350 V P-State FID 0x2 - VID 0x12 (5.0x - 1.100 V) P-State FID 0xA - VID 0x0C (9.0x - 1.250 V) P-State FID 0xC - VID 0x0A (10.0x - 1.300 V) K8 Thermal sensor yes K8 Revision ID 6.0 Attached device PCI device at bus 0, device 24, function 0 Attached device PCI device at bus 0, device 24, function 1 Attached device PCI device at bus 0, device 24, function 2 Attached device PCI device at bus 0, device 24, function 3 Chipset ------------------------------------------------------------------------- Northbridge SiS 761GX rev. 02 Southbridge SiS 966 rev. 59 Graphic Interface AGP AGP Revision 3.0 AGP Transfer Rate 8x AGP SBA supported, enabled Memory Type DDR2 Memory Size 2048 MBytes Channels Single Memory Frequency 200.0 MHz (CPU/5) CAS# latency (CL) 5.0 RAS# to CAS# delay (tRCD) 5 RAS# Precharge (tRP) 5 Cycle Time (tRAS) 15 Bank Cycle Time (tRC) 21 Command Rate (CR) 1T DMI ------------------------------------------------------------------------- DMI BIOS vendor Phoenix Technologies, LTD version R03 date 05/08/2008 DMI System Information manufacturer HP product MediaSmart Server version unknown serial CN68330DGH UUID A482007B-B0CC7593-DD11736A-407B7067 DMI Baseboard vendor Wistron model SJD4 revision A.0 serial unknown DMI System Enclosure manufacturer HP chassis type Desktop chassis serial unknown DMI Processor manufacturer AMD model AMD Sempron(tm) Processor LE-1150 clock speed 2000.0 MHz FSB speed 200.0 MHz multiplier 10.0x DMI Memory Controller correction 64-bit ECC Max module size 4096 MBytes DMI Memory Module designation A0 size 2048 MBytes (double bank) DMI Memory Module designation A1 DMI Memory Module designation A2 DMI Memory Module designation A3 DMI Port Connector designation PS/2 Mouse (internal) port type Mouse Port connector PS/2 connector PS/2 DMI Port Connector designation USB0 (external) port type USB DMI Physical Memory Array location Motherboard usage System Memory correction None max capacity 16384 MBytes max# of devices 4 DMI Memory Device designation A0 format DIMM type unknown total width 64 bits data width 64 bits size 2048 MBytes DMI Memory Device designation A1 format DIMM type unknown total width 64 bits data width 64 bits DMI Memory Device designation A2 format DIMM type unknown total width 64 bits data width 64 bits DMI Memory Device designation A3 format DIMM type unknown total width 64 bits data width 64 bits How do I figure out what options I have for an upgrade?

    Read the article

  • Cannot exit X server, restart, shutdown or drop to tty when VGA monitor active

    - by terdon
    I have a strange problem. If I connect an external VGA monitor to my laptop, exiting the X environment in any way crashes the computer. For example, say I am working with my two monitors (the laptop's and one connected to my VGA port) active. Hitting Ctrl+Alt+F Key should take me down to a tty. What actually happens is that the VGA screen goes blank, as you would expect, but the laptop screen, although still on, shows nothing. I know the screen is on because it is slightly more illuminated than when it is off. When in this state, I can do nothing to regain access to the machine. I have tried: Ctrl+F Key (and even Ctrl+Alt+F Key, just in case) combinations and none seem to have any effect. Ctrl+Alt+Del : Nothing Magic SysRq key: Nothing Blindly typing my username and password and trying to reboot/shutdown or restart GDM or MDM: Nothing The only thing that works is a hard reset. The exact same behavior occurs when kiling the X server through Ctrl+Alt+Backspace, rebooting or shutdown. There is no difference if I reboot/shutdown/log out using the WM's graphical menu or if I use the shutdown or rebootcommands. It is also not WM-dependent. I have the same problem using Cinnamon, Gnome 3, MATE and xfce4. It is, however, VGA dependent. I have tried connecting another VGA monitor and have the same problem. I do not, however, have this problem if a screen is connected to the DisplayPort. It is, therefore, a VGA specific issue. To make things even stranger, this only occurs when both screens are active. If either the laptop screen or the VGA monitor is inactive the problem goes away. Finally, this problem arose when I installed the latest Linux Mint Debian (LMDE). It did not occur with the previous release of LMDE. I am not sure what has changed since I used the same kernel version in both releases (I had upgraded the kernel while on the previous release) and, I think, the same nvidia drivers. Oh, and yes, I have updated the nvidia driver. Hardware: Dell M4500 laptop CPU: Intel Core i7 RAM: 8GB Graphics: nVidia GT216 [Quadro FX 880M] Software: LMDE, kernel 3.2.0-2-amd64 Xorg: 1.11.4 nVidia kernel: 295.20-1+3.2.9-1 Possibly relevant files: /var/log/Xorg.0.log ~/.xsession-errors Does anyone have any ideas how to fix this? Thanks in advance for any help.

    Read the article

  • Recover RAID 5 data after created new array instead of re-using

    - by Brigadieren
    Folks please help - I am a newb with a major headache at hand (perfect storm situation). I have a 3 1tb hdd on my ubuntu 11.04 configured as software raid 5. The data had been copied weekly onto another separate off the computer hard drive until that completely failed and was thrown away. A few days back we had a power outage and after rebooting my box wouldn't mount the raid. In my infinite wisdom I entered mdadm --create -f... command instead of mdadm --assemble and didn't notice the travesty that I had done until after. It started the array degraded and proceeded with building and syncing it which took ~10 hours. After I was back I saw that that the array is successfully up and running but the raid is not I mean the individual drives are partitioned (partition type f8 ) but the md0 device is not. Realizing in horror what I have done I am trying to find some solutions. I just pray that --create didn't overwrite entire content of the hard driver. Could someone PLEASE help me out with this - the data that's on the drive is very important and unique ~10 years of photos, docs, etc. Is it possible that by specifying the participating hard drives in wrong order can make mdadm overwrite them? when I do mdadm --examine --scan I get something like ARRAY /dev/md/0 metadata=1.2 UUID=f1b4084a:720b5712:6d03b9e9:43afe51b name=<hostname>:0 Interestingly enough name used to be 'raid' and not the host hame with :0 appended. Here is the 'sanitized' config entries: DEVICE /dev/sdf1 /dev/sde1 /dev/sdd1 CREATE owner=root group=disk mode=0660 auto=yes HOMEHOST <system> MAILADDR root ARRAY /dev/md0 metadata=1.2 name=tanserv:0 UUID=f1b4084a:720b5712:6d03b9e9:43afe51b Here is the output from mdstat cat /proc/mdstat Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [raid10] md0 : active raid5 sdd1[0] sdf1[3] sde1[1] 1953517568 blocks super 1.2 level 5, 512k chunk, algorithm 2 [3/3] [UUU] unused devices: <none> fdisk shows the following: fdisk -l Disk /dev/sda: 80.0 GB, 80026361856 bytes 255 heads, 63 sectors/track, 9729 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000bf62e Device Boot Start End Blocks Id System /dev/sda1 * 1 9443 75846656 83 Linux /dev/sda2 9443 9730 2301953 5 Extended /dev/sda5 9443 9730 2301952 82 Linux swap / Solaris Disk /dev/sdb: 750.2 GB, 750156374016 bytes 255 heads, 63 sectors/track, 91201 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000de8dd Device Boot Start End Blocks Id System /dev/sdb1 1 91201 732572001 8e Linux LVM Disk /dev/sdc: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00056a17 Device Boot Start End Blocks Id System /dev/sdc1 1 60801 488384001 8e Linux LVM Disk /dev/sdd: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000ca948 Device Boot Start End Blocks Id System /dev/sdd1 1 121601 976760001 fd Linux raid autodetect Disk /dev/dm-0: 1250.3 GB, 1250254913536 bytes 255 heads, 63 sectors/track, 152001 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/dm-0 doesn't contain a valid partition table Disk /dev/sde: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x93a66687 Device Boot Start End Blocks Id System /dev/sde1 1 121601 976760001 fd Linux raid autodetect Disk /dev/sdf: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xe6edc059 Device Boot Start End Blocks Id System /dev/sdf1 1 121601 976760001 fd Linux raid autodetect Disk /dev/md0: 2000.4 GB, 2000401989632 bytes 2 heads, 4 sectors/track, 488379392 cylinders Units = cylinders of 8 * 512 = 4096 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 524288 bytes / 1048576 bytes Disk identifier: 0x00000000 Disk /dev/md0 doesn't contain a valid partition table Per suggestions I did clean up the superblocks and re-created the array with --assume-clean option but with no luck at all. Is there any tool that will help me to revive at least some of the data? Can someone tell me what and how the mdadm --create does when syncs to destroy the data so I can write a tool to un-do whatever was done? After the re-creating of the raid I run fsck.ext4 /dev/md0 and here is the output root@tanserv:/etc/mdadm# fsck.ext4 /dev/md0 e2fsck 1.41.14 (22-Dec-2010) fsck.ext4: Superblock invalid, trying backup blocks... fsck.ext4: Bad magic number in super-block while trying to open /dev/md0 The superblock could not be read or does not describe a correct ext2 filesystem. If the device is valid and it really contains an ext2 filesystem (and not swap or ufs or something else), then the superblock is corrupt, and you might try running e2fsck with an alternate superblock: e2fsck -b 8193 Per Shanes' suggestion I tried root@tanserv:/home/mushegh# mkfs.ext4 -n /dev/md0 mke2fs 1.41.14 (22-Dec-2010) Filesystem label= OS type: Linux Block size=4096 (log=2) Fragment size=4096 (log=2) Stride=128 blocks, Stripe width=256 blocks 122101760 inodes, 488379392 blocks 24418969 blocks (5.00%) reserved for the super user First data block=0 Maximum filesystem blocks=0 14905 block groups 32768 blocks per group, 32768 fragments per group 8192 inodes per group Superblock backups stored on blocks: 32768, 98304, 163840, 229376, 294912, 819200, 884736, 1605632, 2654208, 4096000, 7962624, 11239424, 20480000, 23887872, 71663616, 78675968, 102400000, 214990848 and run fsck.ext4 with every backup block but all returned the following: root@tanserv:/home/mushegh# fsck.ext4 -b 214990848 /dev/md0 e2fsck 1.41.14 (22-Dec-2010) fsck.ext4: Invalid argument while trying to open /dev/md0 The superblock could not be read or does not describe a correct ext2 filesystem. If the device is valid and it really contains an ext2 filesystem (and not swap or ufs or something else), then the superblock is corrupt, and you might try running e2fsck with an alternate superblock: e2fsck -b 8193 <device> Any suggestions? Regards!

    Read the article

  • Need help making site available externally

    - by White Island
    I'm trying to open a hole in the firewall (ASA 5505, v8.2) to allow external access to a Web application. Via ASDM (6.3?), I've added the server as a Public Server, which creates a static NAT entry [I'm using the public IP that is assigned to 'dynamic NAT--outgoing' for the LAN, after confirming on the Cisco forums that it wouldn't bring everyone's access crashing down] and an incoming rule "any... public_ip... https... allow" but traffic is still not getting through. When I look at the log viewer, it says it's denied by access-group outside_access_in, implicit rule, which is "any any ip deny" I haven't had much experience with Cisco management. I can't see what I'm missing to allow this connection through, and I'm wondering if there's anything else special I have to add. I tried adding a rule (several variations) within that access-group to allow https to the server, but it never made a difference. Maybe I haven't found the right combination? :P I also made sure the Windows firewall is open on port 443, although I'm pretty sure the current problem is Cisco, because of the logs. :) Any ideas? If you need more information, please let me know. Thanks Edit: First of all, I had this backward. (Sorry) Traffic is being blocked by access-group "inside_access_out" which is what confused me in the first place. I guess I confused myself again in the midst of typing the question. Here, I believe, is the pertinent information. Please let me know what you see wrong. access-list acl_in extended permit tcp any host PUBLIC_IP eq https access-list acl_in extended permit icmp CS_WAN_IPs 255.255.255.240 any access-list acl_in remark Allow Vendor connections to LAN access-list acl_in extended permit tcp host Vendor any object-group RemoteDesktop access-list acl_in remark NetworkScanner scan-to-email incoming (from smtp.mail.microsoftonline.com to PCs) access-list acl_in extended permit object-group TCPUDP any object-group Scan-to-email host NetworkScanner object-group Scan-to-email access-list acl_out extended permit icmp any any access-list acl_out extended permit tcp any any access-list acl_out extended permit udp any any access-list SSLVPNSplitTunnel standard permit LAN_Subnet 255.255.255.0 access-list nonat extended permit ip VPN_Subnet 255.255.255.0 LAN_Subnet 255.255.255.0 access-list nonat extended permit ip LAN_Subnet 255.255.255.0 VPN_Subnet 255.255.255.0 access-list inside_access_out remark NetworkScanner Scan-to-email outgoing (from scanner to Internet) access-list inside_access_out extended permit object-group TCPUDP host NetworkScanner object-group Scan-to-email any object-group Scan-to-email access-list inside_access_out extended permit tcp any interface outside eq https static (inside,outside) PUBLIC_IP LOCAL_IP[server object] netmask 255.255.255.255 I wasn't sure if I needed to reverse that "static" entry, since I got my question mixed up... and also with that last access-list entry, I tried interface inside and outside - neither proved successful... and I wasn't sure about whether it should be www, since the site is running on https. I assumed it should only be https.

    Read the article

  • How to reset mysql's replication settings completely, without reinstalling it?

    - by user38060
    I set up mysql replication by adding references to binlogs, relay logs etc in my.cnf restarted mysql, it worked. I wanted to change it so I deleted all binlog related files including log-bin.index, removed binlog statements from my.cnf restarted server, works set master to '', purge master logs since now(), reset slave, stop slave, stop master. now, to set up replication again, I added binlog statements to the server. But then I hit this problem when restarting with: sudo mysqld (the only way to see mysql's startup errors) I get this error: /usr/sbin/mysqld: File '/etc/mysql/var/log-bin.index' not found (Errcode: 13) Because indeed, this file does not exist! (I deleted it, while trying to set up a new replication system) Hmm, if I change the config line to: log-bin-index = log-bin.index I get a different error: [ERROR] Can't generate a unique log-filename /etc/mysql/var/bin.(1-999) [ERROR] MSYQL_BIN_LOG::open failed to generate new file name. [ERROR] Aborting The first time I set up replication on this system, I didn't need to create this file. I did the same thing - added references to a previously non-existing file, and mysql created it. Same with relay logs, etc. I don't know why mysql insists on trying to read the old folder. Should I just reinstall the whole package again? That seems like overkill. my my.cnf: [client] port = 3306 socket = /var/run/mysqld/mysqld.sock [mysqld_safe] socket = /var/run/mysqld/mysqld.sock nice = 0 [mysqld] user = mysql socket = /var/run/mysqld/mysqld.sock port = 3306 basedir = /usr datadir = /var/lib/mysql tmpdir = /tmp skip-external-locking bind-address = IP key_buffer = 16M max_allowed_packet = 16M thread_stack = 192K thread_cache_size = 8 myisam-recover = BACKUP table_cache = 64 sort_buffer =64K net_buffer_length =2K query_cache_limit = 1M query_cache_size = 16M slow_query_log_file = /etc/mysql/var/mysql-slow.log long_query_time = 1 log-queries-not-using-indexes expire_logs_days = 10 max_binlog_size = 100M server-id = 3 log-bin = /etc/mysql/var/bin.log log-slave-updates log-bin-index = /etc/mysql/var/log-bin.index log-error = /etc/mysql/var/error.log relay-log = /etc/mysql/var/relay.log relay-log-info-file = /etc/mysql/var/relay-log.info relay-log-index = /etc/mysql/var/relay-log.index auto_increment_increment = 10 auto_increment_offset = 3 master-host = HOST master-user = USER master-password=PWD replicate-do-db = DBNAME collation_server=utf8_unicode_ci character_set_server=utf8 skip-character-set-client-handshake [mysqldump] quick quote-names max_allowed_packet = 16M [mysql] #no-auto-rehash [myisamchk] key_buffer_size = 16M sort_buffer_size = 8M [mysqlhotcopy] interactive-timeout !includedir /etc/mysql/conf.d/ Update: Changing all the /etc/mysql/var/xxx paths in binlog & relay log statements to local has somehow solved the problem. I thought it was apparmor causing it at first, but when I added /etc/mysql/* rw, to apparmor's config and restarted it, it still couldn't read the full path.

    Read the article

  • Windows 7 file-based backup service

    - by Ben Voigt
    I'm looking for a good replacement for Lazy Mirror, since it doesn't support Windows 7 well. Pros: One of the things I really loved about Lazy Mirror is that it always maintains a "full" backup, but does so by only copying modified files. As each file was copied, the old version got archived (moved to an out-of-the-way location). So after mirroring ran, there'd be a complete copy of the file system, which could even be booted if necessary. At the same time, extra space on the backup media was used to store as many older versions of files as possible, without wasting space storing multiple copies of the same version. It seems that with Windows 7 backup, there'd be wasted space storing the same data in both the system image and file backup. It was completely file-based, but also aware of the registry (it had a feature to dump the live registry to hive files in the correct format). The backups were normal NTFS filesystems, no special tool was needed to read them. It automatically cleaned out the oldest previous versions when space ran out (unlike Windows 7 backup which apparently simply starts failing the the backup media fills.) It copied all file attributes including security. Cons: It doesn't deal well with junction points, symbolic links, and hard links. It didn't run as a service without lots of help from firesrv or srvany, and then you couldn't interact with the GUI. Running as a service was necessary to be able to mirror protected OS files. It didn't have open file handling, except for registry hives. I guess that the file-by-file archive and replacement could leave mismatched sets of files, if the mirror was interrupted. This would be the advantage of incremental backup techniques that require old full backup + all intermediate incremental backups to restore. But I don't see this as presenting much of a problem, you'd really only have a boot failure if you had a mixture of pre- and post-service pack files, and I can run a full image backup using another tool before applying a service pack. Does anyone know of a tool that does both full-system backup and storage of old versions of files like Lazy Mirror did (without storing the same data multiple times), and also can run as a service in Windows 7? Free is best of course, but a reasonably priced paid program (e.g. It would be absolutely awesome if it also triggered a backup/mirror pass when a particular external drive was plugged in and generated popup warnings if backups hadn't been run recently)

    Read the article

  • How to get php mail function to work on Debian “squeeze”?

    - by Neel Kamal
    I have installed Apache and PHP5 on my debian server. Firstly I tried it using sendmail. Here is the step by step procedure that I have tried : Step 1: apt-get install sendmail Step 2: /etc/init.d/apache2 restart But this didn't work. Then I tried using external SMTP . My domain is registered on BigRock.I registerd an email address there [email protected] and it gave me the required credentials. On server I installed sSMTP > apt-get install ssmtp > Configured "/etc/ssmtp/ssmtp.conf" file. In the configuration file I added [email protected] mailhub=smtp.fostergen.com:587 (Here I have doubt. I am not sure what to use here. I tried smtp.fostergen.com:587, smtp.fostergen.com:25,mx1.mailhostbox.com :587,mx1.mailhostbox.com:25. I am still not sure what to use here mailhostbox.com. I used mx1.mailhostbox.com as it was the mx entry for my domain on bigrock Here is the screenshot![screenshot of bigrock's email management tool] ) hostname=vs3204.ams2.alvotec.de (I entered the command hostname -f on my server and got it as result ) FromLineOverride=YES UseSTARTTLS=YES [email protected] AuthPass=password provided during email registration on bigrock > edited /etc/ssmtp/revaliases (added " root:[email protected]:mx1.mailhostbox.com :587 " in the last line) > edited php.ini file (sendmail_path = /usr/sbin/ssmtp -t) > /etc/init.d/apache2 restart But this didn't work. After this I tried eSMTP. Steps Performed : > apt-get install esmtp > edited /etc/esmtprc hostname=smtp.fostergen.com:587 username= [email protected] password: password provide by bigrock mda="/usr/bin/procmail -d %T" > linked eSMTP to the legacy Sendmail path by execting the command "ln -s /usr/bin/esmtp /usr/bin/sendmail" > edited php.ini file (/usr/bin/sendmail -t -i) > /etc/init.d/apache2 restart But this technique also failed. I just want to send email to users through php mail function. Kindly help. Where I am going wrong?

    Read the article

  • Filtering Security Logs by User and Logon Type

    - by Trido
    I have been asked to find out when a user has logged on to the system in the last week. Now the audit logs in Windows should contain all the info I need. I think if I search for Event ID 4624 (Logon Success) with a specific AD user and Logon Type 2 (Interactive Logon) that it should give me the information I need, but for the life of my I cannot figure out how to actually filter the Event Log to get this information. Is it possible inside of the Event Viewer or do you need to use an external tool to parse it to this level? I found http://nerdsknowbest.blogspot.com.au/2013/03/filter-security-event-logs-by-user-in.html which seemed to be part of what I needed. I modified it slightly to only give me the last 7 days worth. Below is the XML I tried. <QueryList> <Query Id="0" Path="Security"> <Select Path="Security">*[System[(EventID=4624) and TimeCreated[timediff(@SystemTime) &lt;= 604800000]]]</Select> <Select Path="Security">*[EventData[Data[@Name='Logon Type']='2']]</Select> <Select Path="Security">*[EventData[Data[@Name='subjectUsername']='Domain\Username']]</Select> </Query> </QueryList> It only gave me the last 7 days, but the rest of it did not work. Can anyone assist me with this? EDIT Thanks to the suggestions of Lucky Luke I have been making progress. The below is my current query, although as I will explain it isn't returning any results. <QueryList> <Query Id="0" Path="Security"> <Select Path="Security"> *[System[(EventID='4624')] and System[TimeCreated[timediff(@SystemTime) &lt;= 604800000]] and EventData[Data[@Name='TargetUserName']='john.doe'] and EventData[Data[@Name='LogonType']='2'] ] </Select> </Query> </QueryList> As I mentioned, it wasn't returning any results so I have been messing with it a bit. I can get it to produce the results correctly until I add in the LogonType line. After that, it returns no results. Any idea why this might be? EDIT 2 I updated the LogonType line to the following: EventData[Data[@Name='LogonType'] and (Data='2' or Data='7')] This should capture Workstation Logons as well as Workstation Unlocks, but I still get nothing. I then modify it to search for other Logon Types like 3, or 8 which it finds plenty of. This leads me to believe that the query works correctly, but for some reason there are no entries in the Event Logs with Logon Type equalling 2 and this makes no sense to me. Is it possible to turn this off?

    Read the article

  • Complete Active Directory redesign and GPO application

    - by Wolfgang Kuehne
    after much testing and hundreds of tries and hours invested I decided to consult you experts here. Overview: I want to apply some GPO to our users which will add some specific site to the Trusted Sites in Internet Explorer settings for all users. However, the more I try the more confusing the results become. The GPO is either applied to one group of users, or to another one. Finally, I came to the conclusion that this weird behavior is cause rather by the poor organization in Users and Groups in Active Directory. As such I want to kick the problem from the root: Redesign the Active Directory Users and Groups. Scenario: There is one Domain Controller, and we use Terminal Services (so there is a Terminal Server as well). Users usually log on to the Terminal Server using Remote Desktop to perform their daily tasks. I would classify the users in the following way: IT: Admins, Software Development Business: Administration, Management The current structure of the Active Directory Users and Groups is a result of the previous IT management. The company has used Small Business Server which has created multiple default user groups and containers. Unfortunately, the guys working before me have do no documentation at all. Now, as I inherit this structure I am in the no mans land. No idea which direction to head first. As you can see, the Active Directory User and Groups have become a bit confusing. There is no SBS anymore, but when migrating from SBS to the current Windows Server 2008 R2 environment the guys before me have simply copied the same structure. The real question: Where should I start cleaning from, ensuring that I won't break totally the current infrastructure? What is a nice organization for the scenario that I have explained above? Possible useful info for the current structure: Computers folder contains Terminal Services Computers user group Members: TerminalServer computer located at Server -> Terminalserver OU Member of: NONE Foreign Security Principals : EMPTY Managed Service Accounts : EMPTY Microsoft Exchange Security Groups : not sure if needed, our emails are administered by external service provider Distribution Groups : not sure if needed Security Groups : there are couple of groups which are needed SBS users : contains all the users Terminalserver : contains only the TerminalServer machine

    Read the article

  • Looking for a new backup solution to replace dying tape drive

    - by E3 Group
    We're running Windows Server 2003 SBS and another machine with Server 2003 Standard on it. The SBS server is about 7 years old running pretty much 24/7 - a HP server of some description. We have an Ultrium 448 cycling LTO2 400GB tapes daily and incrementally backing up approximately 100gb worth of data (20gb C:\ and system state, 40gb exchange, 40gb database for some crap marketing software) on BackupExec 10D. As of 5 months ago, the backups have been consistently failing with IO errors, bad reads and some write errors. When I say consistent, I mean every time and we haven't had a proper backup for the entire 5 months - So if the server explodes tomorrow, 7 years worth of data will just cease to exist. I've only just recently rejoined the company and am looking at rectifying the more concerning problems, so the first thing I did was try a backup to an USB2.0 external drive. It was excruciatingly slow. In fact it was so slow it took 40 hours and it still wasn't finished. I ended up cancelling it and reconfiguring the selections again to reduce file size. This, however, isn't a permanent solution. I concluded that the IO error was either from a faulty tape drive (which has a tape stuck in there right now and not coming out) or from a dying SCSI controller. Neither of them are good news and both are extremely expensive to fix. I'm operating on an extremely low budget so have been looking at outsourcing the backups. A company in Sydney (where I'm located) offer incremental online backups via a NAS. It costs almost double a new tape drive but offers monthly repayments which will let us get through times when cash flow is minimal. It seems like a sweet deal but it is still a little bit pricey. So I'm looking for a cheaper, yet reliable solution. Maybe some in-house NAS or something offsite? The idea is to avoid using tapes. Are there any recommendations for rectifying my current situation? Or are tapes the only way to go? I'm concerned that the server will die one day in the near future and I must be able to restore it to another server with different hardware.

    Read the article

  • File Not Found error launching Guest OS in a non-administrator user account

    - by ToreTrygg
    Hi, I am running Fusion 2.0.6 (196839) on an iMac running 10.6.2 with 3 user accounts (1 Administrator). I have Fusion set up to share the Guest OS, and it's been working splendidly for nearly a year. Within the Guest OS (Windows XP PRO), there are also 3 user accounts (1 Administrator). Last night I went to back up my VM to an external drive, and to minimize the file size and transfer time, I deleted all Snapshots but the most-recent one. I then backed up the VM externally (28.23 GB). Today, one of my users tried to launch the Guest OS from within her user account, and received the following error message: "File Not Found: Windows XP Pro-000006.vmdk "This file is required to power on this virtual machine. If this file was moved, please provide its new location." My two choices are Cancel and Browse. When I browse, I can locate the Windows XP Pro-000006.vmdk file, which appears to be contained within the VM file (Windows XP Pro.vmwarevm). However, it still won't launch from a non-Admin user account. If I view the package contents of the VM file from the user account, the above file is present and appears to be created upon each launch of the Guest OS. If I go back to my Administrator account on the Mac and then launch Fusion, the Guest OS works perfectly for all 3 user accounts within XP Pro. I have tried to delete the Guest OS from Fusion's Library within the problem user account, then re-connect it to that Library, but the result is the same. The Guest OS data integrity is 100% -- but is accessible only from the OS X Administrator account. This problem only surfaced after deleting several older Snapshots. Again, the data is there, the Guest OS powers up normally in the Mac's Administrator account, but persistently returns the above error when attempting to power on from a non-Admin account on the Mac. I'm not sure how this is affecting the error, but when I look at Hard Disk Settings, the "unable-to-locate" file is the filename of the virtual HD. I don't want to make any changes to my (working) VM without any advice from the knowledgeable people on this forum. Any help will be greatly appreciated, thanks!

    Read the article

  • Cannot access website from inside network

    - by musclez
    I have a website running from my internal network available at the example IP 192.168.1.5. When I type this in to the browser, it redirects to my domain name ie, "example.com", and gives me Error code: ERR_CONNECTION_REFUSED. Any other machine that is inside of the network can access the website. The website is also accessible outside of the network. Other services from the server, like file sharing or ftp, are available to all machines in the network including the one i'm having issues http issues with. The issue may be linked to a proxy service, but from my understanding the service has been completely disabled and any executable have been uninstalled from the machine. I am wondering if there is some residual proxy information remaining on the machine that limits the connection. I'm fairly positive that "example.com" is what is being blocked by the local machine, and not an IP address being blocked or a faulty connection. When I examine the hosts file, there are no redirects to the local machine for "example.com". There was a rule, as on my other machines within the network: 192.168.1.5 example.com But i have since removed that for troubleshooting purposes. What intrigued me is that when I use the actual IP, the IP address will redirect to the domain in the browser and THEN say ERR_CONNECTION_REFUSED. Server-Side Results The server logs are reporting this: example.com ::1 - - [Date & time] "OPTIONS * HTTP/1.0" 200 126 "-" "Apache/2. 2.22 (Unix) (internal dummy connection)" However, this seems to be irrelevant as it is not triggered when I try to connect to the server with the specified machine. Fiddler results: Host: *example.com* Proxy-Connection: keep-alive Chrome-Side [Fiddler] The connection to 'example.com' failed. Error: ConnectionRefused (0x274d). System.Net.Sockets. SocketException No connection could be made because the target machine actively refused it 01.23.45.67:80 01.23.45.67:80 would be the external IP, which the server and the machine in question both share. I am doing so reading into 0x274d and its coming back with .NET web.config information. I am still at a loss to what to do with this information. I have WireShark running as well. Theres is a lot of sensitive information in the readout and I'm not sure what to extract from it. Either way, if it helps, I can access that information if anyone would like me to. Thanks for the help!

    Read the article

  • Postfix: How to apply header_checks only for specific Domains?

    - by Lukas
    Basically what I want to do is rewriting the From: Header, using header_checks, but only if the mail goes to a certain domain. The problem with header_check is, that I can't check for a combination of To: and From: Headers. Now I was wondering if it was possible to use the header_checks in combination with smtpd_restriction_classes or something similar. I've found a lot information about header_checks and multiple header fields, when searching the net. All of them basically telling me, that one can't combine two header for checking. But I didn't find any information if it was possible to only do a header check if a condition (eg. mail goes to example.com) was met. Edit: While doing some more Research I've found the following article which suggests to add a Service in postfix master.cf, use a transportmap to pass mails for the Domain to that service and have a separate header_check defined with -o. The thing is that I can't get it to work... What I did so far is adding the Service to the master.cf: example unix - - n - - smtpd -o header_checks=regexp:/etc/postfix/check_headers_example Adding the followin Line to the transportmap: example.com example: Last but not least I have two regexp-files for header checks, one for the newly added service, and one to redirect answers to the rewritten domain. check_headers_example: /From:(.*)@mydomain.ain>(.*)/ REPLACE From:[email protected]>$2 Obviously if someone answers, the mail would go to nirvana, so I have the following check_headers defined in the main postfix process: /To:(.*)<(.*)@mydomain.example.com>(.*)/ REDIRECT [email protected]$2 Somehow the Transport is ignored. Any help is appreciated. Edit 2: I'm still stuck... I did try the following: smtpd_restriction_classes = header_rewrite header_rewrite = regexp:/etc/postfix/rewrite_headers_domain smtpd_recipient_restrictions = (some checks) check_recipient_access hash:/etc/postfix/rewrite_table, (more checks) In the rewrite_table the following entries exist: /From:(.*)@mydomain.ain>(.*)/ REPLACE From:[email protected]>$2 All it gets me is a NOQUEUE: reject: 451 4.3.5 Server configuration error. I couldn't find any resources on how you would do that but some people saying it wasn't possible. Edit 3: The reason I asked this question was, that we have a customer (lets say customer.com) who uses some aliases that will forward mail to a domain, let's say example.com. The mailserver at example.com does not accept any mail from an external server that come from a sender @example.com. So all mails that are written from example.com to [email protected] will be rejected in the end. An exception on example.com's mailserver is not possible. We didn't really solve this problem, but will try to work around it by using lists (mailman) instead of aliases. This is not really nice though, nor a real solution. I'd appreciate all suggestions how this could be done in a proper way.

    Read the article

  • Hibernating and booting into another OS: will my filesystems be corrupted?

    - by Ryan Thompson
    Suppose I have Windows and Linux installed on the same computer. If I hibernate Windows, can I boot into Linux without corrupting the Windows filesystem when I resume Windows? What about the other way around? What if I hibernate one, boot into the other, and mount the hibernated filesystem read/write? Read-only? If this is unsafe, is there any way to detect the hibernated state of the other OS and prevent mounting its filesystem? Basically, how far can I push this before it breaks, and how dangerous is it near the edge? I think I know the answers to some of the above questions, but for other ones, I have no idea, and for obvious reasons I have not tested this on my own computer. If someone has tested these, please enlighten the rest of us. I'm not necessarily looking for a specific answer to every question; I'll accept any response that answers a reasonable portion. EDIT: Let me clarify that when I say "hibernate," I mean the process of writing the contents of RAM to the hard disk and completely powering down the computer. In this state, powering the computer back on brings you through the BIOS and bootloader again, and you could theoretically select another operating system on a multi-boot system. Anyway, on with the original question: RESULTS Ok, after everyone's assurances that this would work, I tested it for myself. I set up Ubuntu to remount all ntfs filesystems and external drives read-only before hibernating. There was no need for a similar Windows setup because Windows does not read Linux filesystems. Then, I tried alternately hibernating one operating system and resuming the other, back and forth a few times. I even tried mounting the Windows filesystem from Ubuntu read-write, and creating a few files. Windows didn't complain when I resumed. So, in conclusion, you can more or less freely hibernate in a dual-boot Windows/Linux scenario. Note that I did not test a dual Linux/Linux co-hibernation situation. If you have two or more Linux installs and you hibernate one of them, you might be able to corrupt the filesystem by mounting it from another.

    Read the article

  • Allow email from a particular sender through spam filter

    - by Greg
    We are running exchange 2010 and are using the built in anti-spam feature. We have set up Content Filtering, IP Block List Providers, Sender ID, Sender Reputation and it filters out most of the junk but it also quarantines all emails from one of our customers. It is being quarantined because of the Content Filter agent (Report Below). How can I add an exception for this email address to the Content Filter. I can see how to setup an exception for a delivery address ("Don't filter messages sent TO the following recipients") but I want to add [email protected] to our safe list. I don't want to add the whole domain as it is a very popular ISP in Australia and we often get junk from them. Filter Report: > Diagnostic information for administrators: > > Generating server: something.com > > [email protected] > #550 5.2.1 Content Filter agent quarantined this message ## > > Original message headers: > > Received: from icp-osb-irony-out4.external.iinet.net.au (203.59.1.220) > by server.local.something.com.au (192.5.0.105) with Microsoft SMTP > Server id > 14.1.218.12; Mon, 5 Nov 2012 02:40:40 +1100 X-IronPort-Anti-Spam-Filtered: true X-IronPort-Anti-Spam-Result: > AscOALeLllB8qwLw/2dsb2JhbABEKYUFhiigRQOWCwQEgQiBCIIZFAEBTiwCCAIBBwEIFDkBBBoqARoCAQIDAYd4uEuRXGEDiCWFT44UijeDAw > X-IronPort-AV: E=Sophos;i="4.80,710,1344182400"; > d="scan'208,217";a="55137861" Received: from unknown (HELO > asdf83c05c53a3) ([124.171.2.240]) by icp-osb-irony-out4.iinet.net.au > with ESMTP; 04 Nov 2012 23:40:26 +0800 Message-ID: > <E8C866D0299E4BCB8B156723893EB735@asdf83c05c53a3> From: Customer > <[email protected]> To: 'Person' <[email protected]> > Subject: A long sentance Date: Mon, 5 Nov 2011 06:07:57 +1100 > MIME-Version: 1.0 Content-Type: multipart/alternative; > boundary="----=_NextPart_000_0005_01C5F962.3CD09120" X-Priority: 3 > X-MSMail-Priority: Normal X-Mailer: Microsoft Outlook Express > 6.00.2900.5931 X-MimeOLE: Produced By Microsoft MimeOLE V6.00.2900.6157 Return-Path: [email protected] Received-SPF: None > (server.local.something.com.au: [email protected] does not > designate permitted sender hosts)

    Read the article

  • Proper Imaging Procedures to Restore and Deploy Image with Separate System Reserved Partition

    - by alharaka
    UPDATE: As per my experience here, no one responded. If I do not hear back from TechNet forum members about it, I will post a bounty here, if it makes a difference. I have banged my head against a wall for what seems like all week. I am going to explain my simple procedure, and how none of it, absolutely none, seems to work afterword despite few alternatives and everyone on the internet telling assuming this is how to do it. Diskpart Commands to Create FS Structure REM Select the disk targeted for deployment. REM REM NOTE: Usually disk 0, but drive failure can make it external USB REM media. This will erase the drive regardless! select disk 0 REM Remove previous formatting. clean REM Create System Reserved partition bootloader and files. create partition primary size=100 REM Format the volume format fs=ntfs label="System Reserved" quick override noerr REM Assign the System Reserved partition the D: mount for now assign letter=C REM The main system partition, size not specified to occupy whole drive. create partition primary REM Format the volume format fs=ntfs quick override noerr REM Assign the OS partition the D: mount for now assign letter=D REM Make this the active/bootable partition. sel disk 0 sel partition 1 active REM Close out the diskpart session. exit Now, I thought this was madness, but it turns out the System Reserved partition and standard "System Partition" (C:, commonly both the boot and system volumes where you find the Windows directory AND the bootmgr/ntldr hardware files, this is where Windows 7 diverges) as mounted in the Windows PE session where I run these commands do not matter. See reference here. Since this needs to be BitLocker-ready, enter this crappy System Reserved partition that is separate 100MB of awesome that goes before the regular boot volume. I do this, then I proceed to the next step. Deploy System Reserved and Normal System Images REM C is still the "System Reserved Partition", and the image is just like it sounds. imagex /apply G:\images\systemreserved.wim 1 C: REM D is now what will be the C: system partition on reboot, supposedly. imagex /apply G:\images\testimage.wim 1 D: Reboot the system Now, the images I just captured should look good. This is not even sysprepped, but reapplying the same fscking image I prepared on the same reference workstation hours before. Problem is I get 0xc000000e could not detect the accessible boot device \Windows\system32\winload.exe or different kinds of nonsense revolving around being able to find the boot volume with all the right files. I try different variations of things, now none of them work. I tried repairs with bcdboot, with a fresh System Reserved partition or not, bootrec, and maually editing the damn BCD store with bcdedit. I tried finalizing the above process with and without bootsect /nt60 C: /force. I need to wrap up and automate this procedure. What am I doing wrong that does not make the image happy, but really just miserable.

    Read the article

  • How to enable caching on Apache / Ubuntu Linux?

    - by Jim Mischel
    I have a large (several megabytes) XML file that's updated rather frequently (every 10 minutes or less) and gets a lot of traffic. I'd like to implement some caching to reduce bandwidth and server load. Looking at the Apache documents, I see a dizzying array of configuration options that involve various combinations of mod_expires, mod_headers, and mod_cache (and variants). I end up running in circles and the results aren't what I expect. I'm comfortable editing the various configuration files if I have some idea what I'm supposed to change. But at the moment I'm poking around in the dark and that's never a comfortable feeling. So, perhaps if I describe what I want, somebody here can take me by the hand and say, "This is what you need to do." Periodically, this file, call it "stuff.xml" is updated and a new version copied to the directory. The external url would be, for example, http://example.com/stuff.xml. Understand, this part works. Whenever I request the file, I get the expected result. But the file is big and I want to save bandwidth, so first I'd like to implement conditional GET semantics with the If-Modified-Since header. How do I do this? I've enabled mod_headers and mod_expired and added the <FilesMatching> section in my httpd.conf as recommended in countless examples I've seen online, but that didn't change the behavior when made a conditional GET request. I always get a status 200 with the entire document. So how the heck do I implement this? That'll cut down on neeless transfers. I'd also like to limit the amount of data transferred. Seeing as this is XML, gzipping it should save me 50% or more. My next step would be to somehow gzip the file and, if it's not too difficult, store it in memory. That'll cut down on per-access data transfer, and also reduce disk transfers. So how do I implement this type of caching? Thanks in advance.

    Read the article

  • VPN pptp connection Unable to pass through linux iptables

    - by user221844
    I have set up a windows VPN server behind Linux - Ubuntu box that is working as firewall and proxy server. Now I want people from outside to be able to connect to the VPN server, but the connection is not being established and I get on the client an error 619. I have checked the problem on the internet and it seems a firewall issue. what should I do to make the connection established through the firewall? here is below the information about my setup Firewall-External-IF-IP: 172.16.1.100 Firewall-LAN-IF-IP: 192.168.1.1 VPN-Server-IP: 192.168.1.10 and below is my iptables file content: #Generated by iptables-save v1.4.12 on Thu May 29 12:40:18 2014 *filter :INPUT ACCEPT [162000:140437619] :FORWARD ACCEPT [23282:27196133] :OUTPUT ACCEPT [185778:143961739] :LOGGING - [0:0] -A INPUT -p gre -j ACCEPT -A INPUT -s 192.168.1.10/32 -p tcp -m tcp --sport 1723 -j ACCEPT -A INPUT -s 192.168.1.10/32 -p udp -m udp --sport 1723 -j ACCEPT -A FORWARD -s 192.168.1.0/24 -o EXT_IF -j ACCEPT -A FORWARD -s 192.168.1.0/24 -i EXT_IF -m state --state RELATED,ESTABLISHED -j ACCEPT -A FORWARD -d 192.168.1.10/32 -i EXT_IF -o INT_IF -p tcp -m tcp --dport 1723 -m state --state NEW,RELATED,ESTABLISHED -j ACCEPT -A FORWARD -s 192.168.1.10/32 -i INT_IF -o EXT_IF -p tcp -m tcp --sport 1723 -m state --state RELATED,ESTABLISHED -j ACCEPT -A FORWARD -d 192.168.1.10/32 -i EXT_IF -o INT_IF -p gre -m state --state NEW,RELATED,ESTABLISHED -j ACCEPT -A FORWARD -s 192.168.1.10/32 -i INT_IF -o EXT_IF -p gre -m state --state RELATED,ESTABLISHED -j ACCEPT -A OUTPUT -p gre -j ACCEPT -A OUTPUT -d 192.168.1.10/32 -p tcp -m tcp --dport 1723 -j ACCEPT -A OUTPUT -d 192.168.1.10/32 -p udp -m udp --dport 1723 -j ACCEPT COMMIT # Completed on Thu May 29 12:40:18 2014 # Generated by iptables-save v1.4.12 on Thu May 29 12:40:18 2014 *nat :PREROUTING ACCEPT [17865:1053739] :INPUT ACCEPT [5490:357281] :OUTPUT ACCEPT [3723:223677] :POSTROUTING ACCEPT [3726:223870] -A PREROUTING -p tcp -m tcp --dport 80 -j REDIRECT --to-ports 3128 -A PREROUTING -d 172.16.1.100/32 -i EXT_IF -p tcp -m tcp --dport 1723 -j DNAT --to-destination 192.168.1.10 -A PREROUTING -d 172.16.1.100/32 -i EXT_IF -p gre -j DNAT --to-destination 192.168.1.10 -A PREROUTING -i -h -A POSTROUTING -s 192.168.1.0/24 -o EXT_IF -j MASQUERADE COMMIT # Completed on Thu May 29 12:40:18 2014 # Generated by iptables-save v1.4.12 on Thu May 29 12:40:18 2014 *mangle :PREROUTING ACCEPT [22695965:17811993005] :INPUT ACCEPT [13818180:11522330171] :PREROUTING ACCEPT [17865:1053739] :INPUT ACCEPT [5490:357281] :OUTPUT ACCEPT [3723:223677] :POSTROUTING ACCEPT [3726:223870] -A PREROUTING -p tcp -m tcp --dport 80 -j REDIRECT --to-ports 3128 -A PREROUTING -d 172.16.1.100/32 -i EXT_IF -p tcp -m tcp --dport 1723 -j DNAT --to-destination 192.168.1.10 -A PREROUTING -d 172.16.1.100/32 -i EXT_IF -p gre -j DNAT --to-destination 192.168.1.10 -A PREROUTING -i -h -A POSTROUTING -s 192.168.1.0/24 -o EXT_IF -j MASQUERADE COMMIT # Completed on Thu May 29 12:40:18 2014 # Generated by iptables-save v1.4.12 on Thu May 29 12:40:18 2014 *mangle :PREROUTING ACCEPT [22695965:17811993005] :INPUT ACCEPT [13818180:11522330171] :FORWARD ACCEPT [8527694:6271564562] :OUTPUT ACCEPT [14748508:11899678536] :POSTROUTING ACCEPT [23271280:18170828012] COMMIT # Completed on Thu May 29 12:40:18 2014 hope that I find the solution here ....!! :(

    Read the article

  • Rsync: windows 7, synology: login error and permission denied error

    - by loonboon
    Good day to all of you all, I'm running into strange/stupid errors, and I hope anybody would be so kind to help me out. I have to admit, I am by no means a guru, so please bear with me :-) Situation: -Synology NAS (runs Linux), and Windows 7 desktop (1 normal/restricted user Lisa and 1 admin user). - Data from W7 desktop to be rsynced to synology: /volume1/home/Lisa/Backup - Rsync command: c:\cygwin\bin\rsync -avz /cygdrive/e/Lisa/ [email protected]:/volume1/homes/Lisa/Backup - I've set up ssh per these two threads: a. http://www.cesareriva.com/archives/102 b. http://www.cesareriva.com/archives/112 Now the horrors begin: - root is allowed to run the rsync succesfully, however, he doesn't login automatically (so I can not use rsync in W7 batchscripts, which is of course required). - Lisa is allowed to login automatically but he can not succesfully finish the rsync command because of permission errors: rsync change dir /volume1/homes/Lisa/Backup failed: permissions denied. This happens for each and every file and subdir rsync tries to create. However, the main directory (Backup) is created. When I try to copy files from windows explorer to the directory 'Backup' using the very same user Lisa everything goes smoothly. So, obviously, there is a permission problem somewhere; either my rsync-command isn't correct, or the folder permissions for homes/Lisa aren't correct (but, then again, Windows 7 copies files to that folder without any problems, so that does make me believe the homes/Lisa-permissions don't appear to be the problem). I also tried adding: --chmod=Dugo+x --chmod=ugo+r which I found somewhere on the web, to the rsync-command, but this didn't solve any problem and gave the exact errors. Would anybody please please help me on how to fix this? I am utterly frustrated about this, because I have been trying for 1 month to get everything to work and it simply doesn't work. I bought the big Synology to end the horrors of 20 external USB-disks for once and for all (we have many pictures and home vids of our deceased dogs and want to watch these, the horrors being 'what material is on what disk'). I'll gladly return the favour of somebody helping me out by buying you a nice beer (paypal), if you could end my misery. I am not extremely skilled on Linux (not at all :-( ) so if you could give an extra word when possible so I understand what to do, I'd be very grateful. I really hope somebody can help me out, Thank you in advance, Lisa

    Read the article

  • Why might one host be unable to access the Internet, when it can ping the router and when all other hosts can?

    - by user1444233
    I have a Draytek Vigor 2830n. It's kicking out a 192.168.3.0 LAN. It performs load-balancing across dual-WAN ports, although I've turned off the second WAN to simplify testing. There are many hosts on the LAN. All IPs are allocated through DHCP, most freely allocated from the pool, but one or two are bound to NIC MAC addresses. All hosts can access the Internet, save one. That host (192.168.3.100 or 'dot100' for short) gets allocated an IP address (and the right gateway address, DNS server addresses, subnet etc.) dot100 can ping itself. It can ping the gateway, and access the latter's web interface via port 80. It's responsive and loss-free (sustained ping over a couple of minutes reports no data loss). Yet, for some reason that evades me, dot100 can't ping an external IP address or domain name. I suspect it's never been able to, because it was getting some Internet access from a second adaptor (different subnet), but that's now been turned off, which exposed the problem. In dot100, I've tried: two operating systems (Windows 8 and Knoppix), to rule out anti-virus programs etc. two physical adaptors two cables, on each adaptor two IPs (e.g. .100 and .103 assigned by Mac and .26 from the pool) both dynamic and assigned (MAC-bound) DHCP-allocated IPs but none of this experiments yielded any variation in the result. dot100 is a crucial host. It's a file server for the network, so I need it to be reliably allocated a consistent IP. Can anyone offer a potential solution or a way forward with the analysis please? My guess My analysis so far leads me to believe it's a router issue. I've checked the web interface very carefully. There are no filters setup in Firewall - General Setup or Filter Setup. I suspect it's a corrupted internal routing table, but the web UI shows this as the Routing table: Key: C - connected, S - static, R - RIP, * - default, ~ - private * 0.0.0.0/ 0.0.0.0 via 62.XX.XX.X WAN1 * 62.XX.XX.X/ 255.255.255.255 via 62.XX.XX.X WAN1 S 82.YY.YYY.YYY/ 255.255.255.255 via 82.YY.YYY.YYY WAN1 C 192.168.1.0/ 255.255.255.0 directly connected WAN2 C~ 192.168.3.0/ 255.255.255.0 directly connected LAN2

    Read the article

  • Postfix flow/hook reference, or high-level overview?

    - by threecheeseopera
    The Postfix MTA consists of several components/services that work together to perform the different stages of delivery and receipt of mail; these include the smtp daemon, the pickup and cleanup processes, the queue manager, the smtp service, pipe/spawn/virtual/rewrite ... and others (including the possibility of custom components). Postfix also provides several types of hooks that allow it to integrate with external software, such as policy servers, filters, bounce handlers, loggers, and authentication mechanisms; these hooks can be connected to different components/stages of the delivery process, and can communicate via (at least) IPC, network, database, several types of flat files, or a predefined protocol (e.g. milter). An old and very limited example of this is shown at this page. My question: Does anyone have access to a resource that describes these hooks, the components/delivery stages that the hook can interact with, and the supported communication methods? Or, more likely, documentation of the various Postfix components and the hooks/methods that they support? For example: Given the requirement "if the recipient primary MX server matches 'shadysmtpd', check the recipient address against a list; if there is a match, terminate the SMTP connection without notice". My software would need to 1) integrate into the proper part of the SMTP process, 2) use some method to perform the address check (TCP map server? regular expressions? mysql?), and 3) implement the required action (connection termination). Additionally, there will probably be several methods to accomplish this, and another requirement would be to find that which best fits (ex: a network server might be faster than a flat-file lookup; or, if a large volume of mail might be affected by this check, it should be performed as early in the mail process as possible). Real-world example: The apolicy policy server (performs checks on addresses according to user-defined rules) is designed as a standalone TCP server that hooks into Postfix inside the smtpd component via the directive 'check_policy_service inet:127.0.0.1:10001' in the 'smtpd_client_restrictions' configuration option. This means that, when Postfix first receives an item of mail to be delivered, it will create a TCP connection to the policy server address:port for the purpose of determining if the client is allowed to send mail from this server (in addition to whatever other restrictions / restriction lookup methods are defined in that option); the proper action will be taken based on the server's response. Notes: 1)The Postfix architecture page describes some of this information in ascii art; what I am hoping for is distilled, condensed, reference material. 2) Please correct me if I am wrong on any level; there is a mountain of material, and I am just one man ;) Thanks!

    Read the article

  • Microsoft Office 2003 document (Excel and Word) intermitently, takes 30 seconds to load

    - by Julio Nobre
    I am trying to figure out why a simple .XLS EXCEL workbook is taking, randomly, 30 seconds to open. Before answering: Please, bear mind the following: Problem symptoms Hanging is intermitent and it takes exactly 30 seconds; During hanging there is no cpu or disk activity; It only happens during document load. Every runs smooth after that; Windows Explorer.exe hangs on folder, but all other folders, system and applications are still responsive; There are no consecutive hangings. I have to wait for while to reproduce this behaviour; All samples documents are located on a local drive (C:\BPI); The no document has has macros and have any addins usage; The problem does occurs on others files extensions like .PDF, for example; Office 2003 is being used for several years; The computer is running Windows XP; Computer has several network mapped drives, all addressed to main file server; Recently, main fileserver was replaced by Windows 2011 SBS Standard Edition What I have done so far I have traced machine Explorer.exe, using Process Monitor, added Duration column, and filtered by Duration 1. That's is how I found that hanging was taking exactly 30 seconds. For further information, please refer to Oliver Salzburg tutorial. Using Process Monitor, I have also figured out than five operations were taking most of sample collecting duration. Looking at sample image below, column Operation below you will notice that one single operation was taking 29 seconds; I have tried different documents (.xls and .doc), all of them smaller than 30 KB; I have, temporarily, removed all shortcuts on User Document's folder that were pointing to network drives or shares; I have runned CCleaner to fix registry issues; I made sure that there were no external links on tested workbook or word documents; I have reproduced this behaviour for hours; I have extensivelly researched for hours on the web; Process Monitor's collected and filtered data

    Read the article

  • Server 2008, 2 NICs, 2 fixed IPs - big delays using internet

    - by user46055
    Hi geniuses I have an all in one Windows 2008 server, configured with AD/DHCP/DNS/RRAS - all set up with wizards and no specific tweaking. The server has 2 network adapters : one of which ("MyWAN") is plugged into our office's internet connection, the other ("MyLAN") is plugged into a local switch, which is also where all our desktops are connected. So this one server is doing everything. When first set up, MyLAN had a fixed IP of 192.168.2.1 and served the desktops with DHCP scope 192.168.2.50-99. It also told them to use 192.168.2.1 as DNS and gateway. MyWAN was setup to take its IP etc from DHCP, being handled by the building's router and ADSL modem etc. All desktops were setup to use DHCP. This all worked perfectly fine, until I recently changed MyWAN to have a static IP (I wanted to access it from home, and needed to give it a static IP to port map in the building's router). Things still work, but there is now a long delay when accessing the internet. The actual speed is as before when downloading, but there is a pause of 3-6 secs when connecting to new hosts (for example if I browse to slashdot from either a desktop or the server itself, it'll hang on connecting to slashdot.org, hang again on connecting to *.fsdn, *.google-analytics.com and all the other hosts referenced from the main page). If I ping slashdot.org from the server, I get the following : Pinging slashdot.org [216.34.181.45] with 32 bytes of data: Reply from 192.168.2.1: Destination host unreachable. Reply from 216.34.181.45: bytes=32 time=99ms TTL=239 Reply from 216.34.181.45: bytes=32 time=100ms TTL=239 Reply from 216.34.181.45: bytes=32 time=101ms TTL=239 Pinging anywhere external always seems to hit 192.168.2.1 first, which doesn't seem right. Trying tracert from the server gives the following : Tracing route to slashdot.org [216.34.181.45] over a maximum of 30 hops: 1 MYSERVER01.intranet [192.168.2.1] reports: Destination host unreachable Trying tracert from a desktop gives the following : Tracing route to slashdot.org [216.34.181.45] over a maximum of 30 hops: 1 <1 ms * <1 ms MYSERVER [192.168.2.1] 2 * * * Request timed out. 3 6 ms 6 ms 6 ms dsl-gw1.ge.mer.uk.webtapestry.net [217.151.111.17] 4 38 ms 239 ms 251 ms gw-router.ge.mer.uk.webtapestry.net [217.151.111.13] ...and then all is fine after that. I think that DNS is working fine because the domain names are getting translated to correct IPs immediately. DHCP seems to be okay? So perhaps it's something up with my RRAS setup - although I can't see any option during the setup wizard which I would have filled in differently. I've also tried changing the binding order of the two network connections, to prioritise MyWAN, but that doesn't seem to have done anything. Any idea what's up? Many thanks - Rob

    Read the article

  • western digital caviar black. EXT4-fs error

    - by azat
    Recently I update my HDD on desktop machine, and bought WD Caviar Black. But after I format & copy information to it (using dd), and fix partitions size: I have next errors in kern.log: Aug 27 16:04:35 home-spb kernel: [148265.326264] EXT4-fs error (device sdc2): ext4_mb_generate_buddy:739: group 9054, 32254 clusters in bitmap, 32258 in gd Aug 27 16:07:11 home-spb kernel: [148421.493483] EXT4-fs error (device sdc2): ext4_mb_generate_buddy:739: group 9045, 32254 clusters in bitmap, 32258 in gd Aug 27 16:09:17 home-spb kernel: [148546.481693] EXT4-fs error (device sdc2): ext4_mb_generate_buddy:739: group 10299, 32254 clusters in bitmap, 32258 in gd Aug 27 16:09:17 home-spb kernel: [148546.487147] JBD2: Spotted dirty metadata buffer (dev = sdc2, blocknr = 0). There's a risk of filesystem corruption in case of system crash. Aug 27 16:09:42 home-spb kernel: [148572.258711] EXT4-fs error (device sdc2): ext4_mb_generate_buddy:739: group 4345, 32254 clusters in bitmap, 32258 in gd Aug 27 16:09:42 home-spb kernel: [148572.277591] JBD2: Spotted dirty metadata buffer (dev = sdc2, blocknr = 0). There's a risk of filesystem corruption in case of system crash. Aug 27 16:09:42 home-spb kernel: [148572.278202] EXT4-fs error (device sdc2): ext4_mb_generate_buddy:739: group 4344, 32254 clusters in bitmap, 32258 in gd Aug 27 16:09:42 home-spb kernel: [148572.284760] JBD2: Spotted dirty metadata buffer (dev = sdc2, blocknr = 0). There's a risk of filesystem corruption in case of system crash. Aug 27 16:09:42 home-spb kernel: [148572.291983] EXT4-fs error (device sdc2): ext4_mb_generate_buddy:739: group 9051, 32254 clusters in bitmap, 32258 in gd Aug 27 16:09:42 home-spb kernel: [148572.297495] JBD2: Spotted dirty metadata buffer (dev = sdc2, blocknr = 0). There's a risk of filesystem corruption in case of system crash. Aug 27 16:09:42 home-spb kernel: [148572.297916] EXT4-fs error (device sdc2): ext4_mb_generate_buddy:739: group 9050, 32254 clusters in bitmap, 32258 in gd Aug 27 16:09:42 home-spb kernel: [148572.297940] JBD2: Spotted dirty metadata buffer (dev = sdc2, blocknr = 0). There's a risk of filesystem corruption in case of system crash. Aug 27 16:09:42 home-spb kernel: [148572.303213] EXT4-fs error (device sdc2): ext4_mb_generate_buddy:739: group 4425, 32254 clusters in bitmap, 32258 in gd Aug 27 16:09:42 home-spb kernel: [148572.312127] JBD2: Spotted dirty metadata buffer (dev = sdc2, blocknr = 0). There's a risk of filesystem corruption in case of system crash. Aug 27 16:09:42 home-spb kernel: [148572.312487] EXT4-fs error (device sdc2): ext4_mb_generate_buddy:739: group 4424, 32254 clusters in bitmap, 32258 in gd Aug 27 16:09:42 home-spb kernel: [148572.317858] JBD2: Spotted dirty metadata buffer (dev = sdc2, blocknr = 0). There's a risk of filesystem corruption in case of system crash. Aug 27 16:09:42 home-spb kernel: [148572.322231] EXT4-fs error (device sdc2): ext4_mb_generate_buddy:739: group 4336, 32254 clusters in bitmap, 32258 in gd Aug 27 16:09:42 home-spb kernel: [148572.326250] JBD2: Spotted dirty metadata buffer (dev = sdc2, blocknr = 0). There's a risk of filesystem corruption in case of system crash. Aug 27 16:09:42 home-spb kernel: [148572.326599] EXT4-fs error (device sdc2): ext4_mb_generate_buddy:739: group 4335, 32254 clusters in bitmap, 32258 in gd Aug 27 16:09:42 home-spb kernel: [148572.332397] JBD2: Spotted dirty metadata buffer (dev = sdc2, blocknr = 0). There's a risk of filesystem corruption in case of system crash. Aug 27 16:09:42 home-spb kernel: [148572.341957] EXT4-fs error (device sdc2): ext4_mb_generate_buddy:739: group 5764, 32254 clusters in bitmap, 32258 in gd Aug 27 16:09:42 home-spb kernel: [148572.350709] JBD2: Spotted dirty metadata buffer (dev = sdc2, blocknr = 0). There's a risk of filesystem corruption in case of system crash. Aug 27 16:09:42 home-spb kernel: [148572.351127] EXT4-fs error (device sdc2): ext4_mb_generate_buddy:739: group 5763, 32254 clusters in bitmap, 32258 in gd Aug 27 16:09:42 home-spb kernel: [148572.355916] JBD2: Spotted dirty metadata buffer (dev = sdc2, blocknr = 0). There's a risk of filesystem corruption in case of system crash. Aug 27 16:09:43 home-spb kernel: [148572.401055] EXT4-fs error (device sdc2): ext4_mb_generate_buddy:739: group 10063, 32254 clusters in bitmap, 32258 in gd Aug 27 16:09:43 home-spb kernel: [148572.404357] JBD2: Spotted dirty metadata buffer (dev = sdc2, blocknr = 0). There's a risk of filesystem corruption in case of system crash. Aug 27 16:09:43 home-spb kernel: [148572.414699] EXT4-fs error (device sdc2): ext4_mb_generate_buddy:739: group 10073, 32254 clusters in bitmap, 32258 in gd Aug 27 16:09:43 home-spb kernel: [148572.420411] JBD2: Spotted dirty metadata buffer (dev = sdc2, blocknr = 0). There's a risk of filesystem corruption in case of system crash. Aug 27 16:09:43 home-spb kernel: [148572.493933] EXT4-fs error (device sdc2): ext4_mb_generate_buddy:739: group 9059, 32254 clusters in bitmap, 32258 in gd Aug 27 16:09:43 home-spb kernel: [148572.493956] JBD2: Spotted dirty metadata buffer (dev = sdc2, blocknr = 0). There's a risk of filesystem corruption in case of system crash. One time, machine rebooted (not manually), when I turn it on, it runs fsck on /dev/sdc2 and fix some errors and some files are missing on /dev/sdc2 I'v check /dev/sdc2 for badblocks, it doesn't have it ( using e2fsck -c /dev/sdc2 ) Here is the output of fsck http://pastebin.com/D5LmLVBY What else I can do to understand what's wrong here? BTW for /dev/sdc1 no message like that, in kern.log Linux version: 3.3.0 Distributive: Debian wheezy

    Read the article

  • How do i enable innodb on ubuntu server 10.04

    - by Matt
    Here is my entire my.cnf [client] port = 3306 socket = /var/run/mysqld/mysqld.sock # Here is entries for some specific programs # The following values assume you have at least 32M ram # This was formally known as [safe_mysqld]. Both versions are currently parsed. [mysqld_safe] socket = /var/run/mysqld/mysqld.sock nice = 0 [mysqld] key_buffer = 224M sort_buffer_size = 4M read_buffer_size = 4M read_rnd_buffer_size = 4M myisam_sort_buffer_size = 12M query_cache_size = 44M # # * Basic Settings # # # * IMPORTANT # If you make changes to these settings and your system uses apparmor, you may # also need to also adjust /etc/apparmor.d/usr.sbin.mysqld. # user = mysql socket = /var/run/mysqld/mysqld.sock port = 3306 basedir = /usr datadir = /var/lib/mysql tmpdir = /tmp skip-external-locking # # Instead of skip-networking the default is now to listen only on # localhost which is more compatible and is not less secure. bind-address = 127.0.0.1 # # * Fine Tuning # #key_buffer = 16M max_allowed_packet = 16M thread_stack = 192K thread_cache_size = 8 # This replaces the startup script and checks MyISAM tables if needed # the first time they are touched myisam-recover = BACKUP #max_connections = 100 #table_cache = 64 #thread_concurrency = 10 # # * Query Cache Configuration # query_cache_limit = 1M #query_cache_size = 16M # # * Logging and Replication # # Both location gets rotated by the cronjob. # Be aware that this log type is a performance killer. # As of 5.1 you can enable the log at runtime! #general_log_file = /var/log/mysql/mysql.log #general_log = 1 log_error = /var/log/mysql/error.log # Here you can see queries with especially long duration #log_slow_queries = /var/log/mysql/mysql-slow.log #long_query_time = 2 #log-queries-not-using-indexes # # The following can be used as easy to replay backup logs or for replication. # note: if you are setting up a replication slave, see README.Debian about # other settings you may need to change. #server-id = 1 #log_bin = /var/log/mysql/mysql-bin.log expire_logs_days = 10 max_binlog_size = 100M #binlog_do_db = include_database_name #binlog_ignore_db = include_database_name # # * InnoDB # # InnoDB is enabled by default with a 10MB datafile in /var/lib/mysql/. # Read the manual for more InnoDB related options. There are many! # # * Security Features # # Read the manual, too, if you want chroot! # chroot = /var/lib/mysql/ # # For generating SSL certificates I recommend the OpenSSL GUI "tinyca". # # ssl-ca=/etc/mysql/cacert.pem # ssl-cert=/etc/mysql/server-cert.pem # ssl-key=/etc/mysql/server-key.pem [mysqldump] quick quote-names max_allowed_packet = 16M [mysql] #no-auto-rehash # faster start of mysql but no tab completition [isamchk] key_buffer = 16M # # * IMPORTANT: Additional settings that can override those from this file! # The files must end with '.cnf', otherwise they'll be ignored. # !includedir /etc/mysql/conf.d/ And here is my show engines call....i have no idea what i need to do to enable innodb show engines; +------------+---------+----------------------------------------------------------------+--------------+------+------------+ | Engine | Support | Comment | Transactions | XA | Savepoints | +------------+---------+----------------------------------------------------------------+--------------+------+------------+ | MyISAM | DEFAULT | Default engine as of MySQL 3.23 with great performance | NO | NO | NO | | MRG_MYISAM | YES | Collection of identical MyISAM tables | NO | NO | NO | | BLACKHOLE | YES | /dev/null storage engine (anything you write to it disappears) | NO | NO | NO | | CSV | YES | CSV storage engine | NO | NO | NO | | MEMORY | YES | Hash based, stored in memory, useful for temporary tables | NO | NO | NO | | FEDERATED | NO | Federated MySQL storage engine | NULL | NULL | NULL | | ARCHIVE | YES | Archive storage engine | NO | NO | NO | +------------+---------+----------------------------------------------------------------+--------------+------+------------+ 7 rows in set (0.00 sec)

    Read the article

< Previous Page | 357 358 359 360 361 362 363 364 365 366 367 368  | Next Page >