Search Results

Search found 93603 results on 3745 pages for 'one to many'.

Page 365/3745 | < Previous Page | 361 362 363 364 365 366 367 368 369 370 371 372  | Next Page >

• eMachine W5243 won't POST; fans run but optical drive will not open.

  - by NicciAdonai

  Symptoms are what is described in the title. The machine reacts to the power button being hit by spinning up the two fans: CPU and PSU. The hard drive (SATA) spins up as well. No other reaction. This one symptom is particularly weird, though: the optical drive will not open with the IDE cable attached, but if I unplug it from the mobo it will. I can turn the PC on with it attached, won't open; then unplug IDE while it is still on, WILL open; then plug IDE back in with the PC STILL ON, WON'T open. I have disconnected every peripheral unnecessary to POST. These include: mouse/keyboard, PCI modem, the IDE optical drive (power and data), and the SATA HDD (power and data). Video is onboard. The only two things connected are DB15 video and power cable. There were 2 512 MB DDR2 sticks of RAM in it. I have tried running it with just one of them, then switched the other in. Currently seated is a completely different 1 GB stick that I keep around for troubleshooting purposes, and I have tried it in both slots. I have replaced the CMOS battery with a used one I had lying around, and which worked in the computer it came out of. I have tested the PSU with a tester to confirm it was good, then tried connecting another PSU just in case--same symptoms. I have even tried a suggestion I found elsewhere on this site wherein one disconnects power from the PSU and then presses the PC's power button twice, thereby "resetting" the PSU. Currently I am trying yet another suggestion: turn it on and wait an inordinate amount of time for POST. Any help would be appreciated.

  Read the article

• big speed difference on a network link with and without VPN tunnel

  - by xirtyllo

  Scenario: We have a network link between two offices. The link is provided by a third party company through a VLAN on their network, but to us it is totally transparent -as if we had a simple ethernet cable going from one location to the other-. We have one router at each side of the link, with 3 VPN tunnels in between the two. The test: When I test the speed of the network link with the routers in place, with one laptop directly connected to the router on each side, I consistently get ~30/35Mbps. But if I take out the routers and I test the link connecting the laptops directly to the ethernet cable at each side, I consistently get ~85/88Mbps. It's quite a big performance hit, and I would tend to think that the VPN tunnels are responsible for the slow down. Is it normal that this configuration (two routers with three VPN tunnels between them) takes away so much bandwidth? More info: The encryption algorithm used for the VPN tunnels is AES128. The routers model is Zyxel USG200 and Zyxel USG1000, and their CPU, memory, and storage use is well within normal limits. The nominal bandwidth of the network link is 100Mbps. The network link in question is supplied by a third party company (the building in between our two offices). Basically it passes through their network as a VLAN, but the VLAN is completely transparent to us (e.g. no configuration required on our side, just like one single cable from end to end). Unfortunately (or maybe fortunately) I cannot directly test different routers configurations as I'm not the person in charge of it.

  Read the article

• How to generate customized sudoers files in puppet depending on the environment they're deployed to?

  - by gozu

  the sysadmins are present in the sudoers files of all environments, but other sudoers are not. Different environments all have slightly different sudoers. Most of the time, 90% of users are the same, and 10% vary so we cannot have only one sudoers file for everything. Right now, we are using puppet with 10 different files with names like sudoers.production1, sudoers.production2, sudoers.production3, sudoers.testing1, sudoers.staging1 and so forth. Puppet then picks the file to deploy based on the server's $domain (ex: dbserver.staging1.acme.com) or $hardwaremodel. It works fine but it's a nightmare to maintain so many files. I'd like to autogenerate sudoers files based on the server's domain and have only one big file with all the sudoers permissions for all users and all environments. Something that looks like: User_Alias ADMINS = abe, bob, carol, dave case $domain { "staging1.acme.com" { #add dev1,dev2,tester1,tester2 to sudoers file } "testing2.acme.com" { #add tester1, tester3, tester4 to sudoers file } What's the best way to go about this? Suggestions for alternatives are welcome. I'd appreciate any tips. Update 1: For security reasons, we'd rather not concatenate a bunch of files from a folder located on a puppet client in case someone puts a file in there (maliciously or not) and either breaks the combined file or inserts something in it. Most importantly, for usability, we'd like to keep the number of sudoers related files (fragment or complete) on puppet server to either 3 (prod/stage/test) or preferably 1 file. this file would (somehow) generate sudoers files on the puppet server and send one customized file to each puppet client. The purpose of this would be only searching for a username in a single file and removing it quicker than doing it on 11 files. When adding a user to a bunch of environments, it won't be as quick, but only one file would need to be opened and looked at, greatly reducing the chances of an omission. our Sudo version is 1.6.9p8 so we can't use /sudoers.d folder, only a sudoers file.

  Read the article

• Amazon AWS EC2 + Puppet, get Puppet to know AWS instance tags

  - by Piotr Jasiulewicz

  I am having a problem with my AWS deployment, fairly new to AWS and Puppet. So coming to my question - can you distinguish puppet nodes with AWS machine tags or CNAME domains? A little background about the plan: have multiple clusters of machines, one php cluster, one legacy php cluster, one java cluster, one perl cluster control configuration with puppet - still pretty new to puppet but as a developer I like the idea of being able to version control configuration of servers have autoscaling enabled on those clusters - obviously the main benefit of the cloud that makes the much hight cost when it comes to any reasonable performance worth it (those amazon machines are slower than my phone...) deployment controlled by Capistrano, this makes things a lot easier So in AWS you get those super nasty public/private machine dns's... no way you can identify machines on those. In order to easer the problem, seams like AWS want's you to tag everything - so I did. Found a script that makes a CNAME record for each machine with the tag "ShortName" thanks to the Route53 API. Every machine has a ShortName tag that becomes its CNAME, unfortunately puppet still resolves the private dns name. I'd like to have node 'perl-cluster'{} in puppet, anyone any clue ho to achieve this? Thanks

  Read the article

• Two hosting providers running simultaneously... possible / not possible? good practice / unnecessary?

  - by user29600

  For the sake of their reputation, I won't mention the names. But I'll just use: Business I worked for previously - ABC Web Dev Hosting company they used - XYZ Hosting I recently found out that XYZ Hosting had some sort of incident where they ended up losing a lot of their client's data - including ABC Web Dev's. ABC Web Dev was able to recover some of their customer's websites, after pulling them from their local development computers and putting them up on another hosting provider. They ended up losing a lot of clients because of it and their reputation ruined. I'm starting my own web dev company and I don't want to run into this same issue. I'm planning on using Rackspace but, although they are a great company, according to wikipedia they still have had downtime in their past. I thought it might be a good idea to try to run two providers at once, to ensure that if anything happened in one the websites would still be live because of the other. I know the websites would have to be pulling from one server at all times, but if there's a way to redirect requests to the second server if the first one is down that would solve my issue. As a note, we will have a staging environment setup locally which will allow for quick recovery if a provider did have any issues, however I'd like to avoid any downtime at all if possible. So my questions are: Has anyone tried running two providers simultaneously? Would this be considered good practice or am I going too far? Is there really any way to run two simultaneously where one server acts as a backup?

  Read the article

• award phoenix bios not recognizing my sata hdd.

  - by josh

  What am I doing wrong? I have a custom built comp with a Fatal1ty AA8XE mobo. It has 4 SATA ports and one IDE port. When i first got it, I had a really hard time putting in more than one hard drive. Right now i have one 120gb IDE HDD on master and my DVD+-RW on slave connected to the one IDE spot on the mobo. I ripped a bunch of movies and filled up my HDD, so I got a WD 80gb SATA drive. I plugged it into SATA1 and hooked up the power, turned on comp, went into bios. The only thing in any option in any of the menues in this crazy lookin bios is a thing that says "SATA mode". i put it on IDE, set it so PATA is primary, SATA is secondary. booted up my comp, nothin. Not recognizing the SATA. I went back into the bios and checked it all again. I saw that it says SATA2 and SATA4 are the secondaries so i put it on SATA2, booted, nothing, same with SATA4, same with SATA3, all same as SATA1. Bios and wt os are not recognizing the drive as being there at all. I even downloaded and printed the almost 100 page manual for the mobo, read the entire thing, and still can't figure it out. I know there are a lot of people out there smarter than me when it comes to computers. So please, somebody, anybody, please tell me something that I'm not seeing. Some setting somewhere that I didn't configure right. There is something, obviously, but I can't find it. As far as i can tell, everything is set perfectly fine for my 120gb to be the master and the SATA to be the slave. I don't know what I'm doing wrong but I'm seriously about to throw this computer out the window. thankyou in advance to whoever attempts to help.

  Read the article

• ZFS: Mirror vs. RAID-Z

  - by John Clayton

  I'm planning on building a file server using OpenSolaris and ZFS that will provide two primary services - be an iSCSI target for XenServer virtual machines & be a general home file server. The hardware I'm looking at includes 2x 4-port SATA controllers, 2x small boot drives (one on each controller), and 4x big drives for storage. This allows one free port per controller for upgrading the array down the road. Where I'm a little confused is how to setup the storage drives. For performance, mirroring appears to be king. I'm having a hard time seeing what the benefit would be of using RAIDZ over mirroring would be. With this setup I can see two options - two mirrored pools in one stripe, or RAIDZ2. Both should protect against 2 drive failures, and/or one controller failure...the only benefit of RAIDZ2 would be that any 2 drives could fail. The storage should be 50% of capacity in both cases, but the first should have much better performance, right? The other thing I'm trying to wrap my mind around is the benefit of mirrored arrays with more than two devices. For data integrity what, if any, would be the benefit of a RAIDZ over a three-way mirror? Since ZFS maintains file integrity what does RAIDZ bring to the table...doesn't ZFS's integrity checks negate the value of RAIDZ's parity?

  Read the article

• What open source ecommerce webshops offer #1: usability, #2: PayPal integration, and #3: ease of administration and use

  - by Jonathan Hayward

  I've spent several days trying to deploy Satchmo, in the process asking several questions about deployment (http://stackoverflow.com/questions/11277407/can-anyone-explain-this-error-message-deploying-a-satchmo-project-under-gunicorn, http://stackoverflow.com/questions/11277685/is-there-a-howto-to-fcgi-for-deploying-satchmo, and http://stackoverflow.com/questions/11278295/what-is-the-most-stable-release-of-satchmo). Django's tagline is "The web framework for perfectionists with deadlines," and Satchmo's tagline is equally forceful: "The webshop for perfectionists with deadlines." I'm looking more to set up, configure, design, etc., rather than code for this one, and I'm taking a bit of a hint that for me at least the "with deadlines" bit is something that I cannot manage. Deployment has been a time sink. So, taking a step back, I don't specifically need to edit and extend the source code; what I want are first, good usability and a clean experience for the end-user, then being easy to deploy/install/manage/maintain, and enough so that even if you're having a slow day it should at most be one day's work to install, one day's work to get running, and one day's work to rebrand as white label (for simple branding). What ecommerce webshops should I be looking at?

  Read the article

• How to fix a Postfix/MySQL/Dovecot Unknown Host Issue?

  - by thiesdiggity

  I am having an issue with one of my Postfix/Dovecot mail servers and I'm unsure how to fix the problem. I will try to explain it in detail, here it goes: I have an Ubuntu server setup using Virtual hosting with Postfix, Dovecot and MySQL. We have one domain setup as a virtual domain, for this example I am going to use mail.example.com. Under that domain we have one email address. I have another server (MS Exchange) setup using another one of my sub-domains, ex.example.com. The problem is that when I SMTP into the account on mail.example.com and try to send an email to an account on ex.example.com, I get the email returned back to us with an "unknown host" error. Now, I know that the mail.example.com server can resolve the ex.example.com domain because I can ping/dig while SSH'd into it. I can also log into Postfix via Telnet and send an email to an ex.example.com mailbox. I'm guessing that it has something to do with Postfix/Dovecot looking locally for the domain in the virtual domain list because of the tld domain (example.com)? If that's the case, how do I get Postfix/Dovecot to only look locally for the entire URL (mail.example.com) and if it doesn't find it, send it to the correct server by looking up the MX/A records (which I know exist and are setup correctly)? I have been working on this all day and any guidance would be GREATLY appreciated! Thanks for your time!

  Read the article

• iOS 6 in-app email does not send from within any app that supports it

  - by Joe Termine

  A strange problem -- Last night I upgraded to the final release of iOS 6 on my iPhone 4S and my iPad 2. When I open an app that allows you to send emails from within the app (e.g. adobe Reader, TurboScan, etc.) -- doesn't matter which one -- I am prompted with the email dialog from within the app, I can compose the message, but when I go to send one of two things will happen: either the email sending sound will "swoosh" and the dialog will close (leading me to think it worked) or some apps with good error handling will say there is an "error sending email." The error logs on my device are not reporting errors. It's just that the email doesn't really send. I have two Exchange mail boxes on these devices. One connects to a corporate network hosting on-premise exchange 2007 and the other connects to Gmail over the exchange interface. Have attempted to delete and re-pair these accounts (one at a time) without any change. I'm wondering if others are experiencing this problem, or whether I should just wipe the devices and chalk it up to (another) failed upgrade. Thoughts much appreciated. Joe

  Read the article

• Distribute IP packets accross different NIC queues with MSI (Message Signalled Interrupts)

  - by Ansis Atteka

  NetXtreme II BCM5709 Gigabit Ethernet NIC supports MSI feature (Message Signaled Interrupts) and it has 8 queues. Each queue has its own Interrupt handler in /proc/interrupts. What I am trying to accomplish is to tell NIC which packets should go to which queue. Questions: Is it possible to manually specify which IP packets should go to which queue by encapsulated protocol type (e.g. IPsec packets go in one queue, while TCP packets go in another queue)? If it is possible - how can I do it under Linux? If it is not possible - should I look at MSI-X capable NIC cards to solve this problem? More details: We have one Interface that is terminating IPSec and forwarding/terminating TCP connections. The IPSec packet decryption is inlined (this means that decryption is done under the same ksoftirqd/X context). We are trying to find out if we will be able to improve total performance if IPSec packets will be scheduled on another CPU than TCP packets. One more limitation is that IPSec code is not MP-safe, hence I can not run it under more than one ksoftirqd/X. By default it seems that packets are distributed/hashed by source IP over the 8 NIC queues. The bottleneck is IPSec that chokes out TCP traffic while it is decrypting/encrypting IPSec packets at ~100% CPU. OS is Ubuntu 10.10 (2.6.32-27-server) and NIC is Broadcom BCM5709.

  Read the article

• Can't connect to a Hyper-V VM from anywhere but the host OS

  - by Elbelcho

  I have an unusual situation on hand where I'm able to connect to a Hyper-V guest VM from the HOST, but not from anywhere but the host. The VM is running WIn2k8R2 and has IIS installed and Remote Desktop enabled. If I browse to the IP from the host OS, the IIS7 page displays. I can also RDP into the guest OS from the host as well as ping. From OFF the host, RDP, web and ping all fail. If I completely shut off the guest VM's firewall, ping will then start to respond, but all RDP and port 80 still don't. The physical host machine has 2 nics installed, but only one is plugged in. The one plugged in has a static IP. I have one Hyper-V virtual network and it's set to external. The guest VM has one NIC with a different static IP than the host, but both are on the same subnet. The host machine is joined to the domain, the guest VM is not. Any sugestions? Thanks so much for any help you may be able to provide!

  Read the article

• How to wire 20 computers and 20 phones and 1 server into LAN?

  - by John Smith

  I have currently 3 switches Two Netgear JFS524 with 24 slots, One Belkin with 16 slots. Server DSL Internet Router. Main question is how to connect switches together, two Netgear's are next to each other, yet one is about 100 feet away and holds about 5 computer and 5 phones. If i connect them with only 1 wire will that limit bandwidth? e.g. all 23 computers will be limited to speed of one CAT5e cable? If i connect switches with 2 cables will this give speed boost? What's the ideal scenario should i just move the third switch next to other two? Will the speed of computer connected to white switch be same as computer connected to top switch? Will moving white switch right next top switch and having 16 wires comming 100 feet instead of 1 wire comming 100 feet make it faster? EDIT 1: I actually have NETGEAR ProSafe GS105 Gigabit switch its only has 4 ports in it though, you think i can have use of it in current setup? Like connect all 3 switches and server into it and keep internet router and phone server on one of the slower switches EDIT 2: Everyone mention gigabit switches, but will they do any difference with 10/100 network cards? I then have to use gigabit cards in every computer too? I could in server perhaps, but users will be 10/100

  Read the article

• How to compare old CPU to new CPU?

  - by Lasse V. Karlsen

  I hope this question doesn't get closed at once :) I have an old laptop, a Compaq NC4200, which is going its final laps around the track these days. Battery is dead, and everything kinda runs slow. It also has only 1GB of memory, and even though I don't know if it can take more, I probably wouldn't be able to get hold of any that matches without having to special order it. The size, however, has been ideal for my usage pattern, so I'm looking to replace it with a similarly sized laptop, at least in the same size category. However, it's been a while since I tried keeping track of CPUs, so I have a question. The old laptop has a Intel Pentium M 760 1.86GHz processor. One laptop I found online has a Intel Pentium SU4100 1.3GHz dual-core. This type of processor seems to be quite common in the price and size-range I've been looking. What kind of relative performance boost could I expect from the old one to the new one? I am not expecting a "about 7.45x speed", but some indication would be nice. For instance, dual-core tells me it might be akin to 2.6GHz, but I assume I can't simply compare 1.86GHz to 2.6GHz and expect the new one to run about 1.4x as fast, I expect more these days. Or is that unrealistic for this kind of processor? Do I need to up my price range and go for a 2+ GHz processor?

  Read the article

• Cannot set up dual monitors correctly in Fedora15 with KDE.

  - by adivasile

  I have 2 monitors: 24" LCD connected via DVI(primary) 19" LCD connected via VGA(secondary) Everytime Fedora starts the second display is always set to clone the first one and they both run at 1280x1024 and I always have to disable the 19" monitor, in order for the bigger one to run at 1920x1080. I want to set them up so that my secondary monitor extends the primary one.The problem is that no matter what kind of configuration I choose it has no effect.My secondary monitor remains disabled. I've tried using both the Display manager from KDE and the ATI Control Panel and the behaviour is always the same.The moment I click apply, the screen flickers and nothing changes. I've succesfully used the extended setup in Fedora15 with Gnome3. I have a RadeonHD 4300 series videocard and I'm using the drivers downloaded from the AMD site. This is the output of xrandr -q : Screen 0: minimum 320 x 200, current 1920 x 1080, maximum 1920 x 1920 VGA-0 connected (normal left inverted right x axis y axis) 1280x1024 75.0 60.0 1280x960 60.0 1152x864 75.0 1024x768 75.0 70.1 66.0 60.0 832x624 74.6 800x600 72.2 75.0 60.3 56.2 640x480 75.0 72.8 66.7 59.9 720x400 70.1 DVI-0 connected 1920x1080+0+0 (normal left inverted right x axis y axis) 477mm x 268mm 1920x1080 60.0*+ 60.0 1680x1050 59.9 1600x900 60.0 1280x1024 75.0 60.0 1280x960 60.0 1152x864 75.0 1280x720 60.0 1152x720 60.0 1024x768 75.0 60.0 832x624 74.6 800x600 75.0 60.3 640x480 75.0 59.9 720x400 70.1 Later edit: The problem seems to come from the ATI drivers.I managed to set up the monitors like I wanted after I uninstalled the drivers. Unfortunately I'm working on an OpenCL project so I had to reinstall them.The moment I did that, all my previous settings were forgotten and I was back to square one.

  Read the article

• Windows 7 DHCP Default Gateway not Overridden by manual Default Gateway

  - by dgwilson

  We have recently installed Windows 7 for student computers. All student computers must be routed through our content filter which is located at 192.168.0.63. This was done in WinXP by adding a Default Gateway in the network adapter settings TCP/IP Properties Advanced Default Gateway. All teacher computers are routed through the DHCP assigned Default Gateway of 192.168.0.1. In WinXP the dhcp default gateway was correctly overridden by this manual setting. In Win7 it appears that the dhcp default gateway is retained and the manual one is added to the list so that there are two with the dhcp one having the primary metric. I have tried several ways to remove the dhcp default gateway such as, running the "route delete 0.0.0.0 192.168.0.1" command. Doing this from an administrator command prompt works but it just resets upon reboot. I've tried adding this command to the registry's Run section but it seems to run as a non-administrator and therefore will not complete successfully. Is there any way to prevent this and force the manual default gateway to override the dhcp one? Or to remove the dhcp assigned one automatically on boot/login? HELP! We CANNOT allow student computers to connect to the internet without going through the content filter.

  Read the article

• Windows 7 DHCP Default Gateway not Overridden by manual Default Gateway

  - by dgwilson

  We have recently installed Windows 7 for student computers. All student computers must be routed through our content filter which is located at 192.168.0.63. This was done in WinXP by adding a Default Gateway in the network adapter settings TCP/IP Properties Advanced Default Gateway. All teacher computers are routed through the DHCP assigned Default Gateway of 192.168.0.1. In WinXP the dhcp default gateway was correctly overridden by this manual setting. In Win7 it appears that the dhcp default gateway is retained and the manual one is added to the list so that there are two with the dhcp one having the primary metric. I have tried several ways to remove the dhcp default gateway such as, running the "route delete 0.0.0.0 192.168.0.1" command. Doing this from an administrator command prompt works but it just resets upon reboot. I've tried adding this command to the registry's Run section but it seems to run as a non-administrator and therefore will not complete successfully. Is there any way to prevent this and force the manual default gateway to override the dhcp one? Or to remove the dhcp assigned one automatically on boot/login? HELP! We CANNOT allow student computers to connect to the internet without going through the content filter.

  Read the article

• Issues with sustained traffic with PFSense

  - by Farseeker

  Last week we had to replace our PFSense firewall because it had a catastrophic hardware failure. All but one of the NICs were taken out of the old server and put into the new one. The one NIC that was not moved was the LAN NIC as this is on-board. The other NICs are all WAN connections and the must all be present (i.e. I can't disable one just for the sake of testing) After re-installing PFSense and restoring our backup of the configuration, everything came back online just fine, however on the new hardware any download that takes longer than about 10 seconds just times out in the middle. Example 1: Downloading from Microsoft.com goes at about 900k/sec and times out after about 10 seconds (thus, just under 10Mb of content) Example 2: Downloading from cnet.com goes at about 300k/sec and times out after about 10 seconds (thus, about 3Mb of content). By times out, I mean that the download just stops, and you have to pause/resume to get the next part done, repeat and rinse until the download is complete. However it's not consistant, sometimes it's 10 seconds, sometimes it's 4 seconds, and it sometimes you can't even load a heavy HTML page because the page never finishes. I assume this is most likely because PFSense does not like the onboard NIC, as this is the primary difference between the two servers. It's recognised as NFE0, and there's no room in the server for any more NICs and I don't have any dual-port NICs handy to experiment with a different LAN connection. I've never had to troubleshoot this sort of issue before. Can anyone give me some pointers about where to start? Linux is not my forte so please be kind!

  Read the article

• Should I enabled 802.3x hardware flow control?

  - by Stu Thompson

  What is the conventional wisdom regarding 802.3x flow control? I'm setting up a network at a new colo and am wondering if I should be enabling it or not. My oh-cool-a-bright-and-shiny-new-toy self wants to enable it, but this seems like one of those decisions that could blow up in my face later on. My network: An HP ProCurve 2510G-24 switch A pair of Debian 5 HP DL380 G5's with built-in NC373i 2-port NIC LACP'd as one link. 9000 jumbo frames enabled. (Application) A pair of hand-built Ubuntu server with 4-port Intel Pro/1000 LACP'd as one link. 9000 jumbo frames enabled. (NAS) A few other servers with with single 1Gbps ports, but one with 100Mbps. Most of this kit is 802.3x. I've been enabling it as I go along, and am about to test the network. But as my 'go live' day nears, I am worried about the 802.3x decision as I've never explicitly used it before. Also, I've read some 10-year old articles out there on the Intertubes that warn against using flow control. Should I be enabling 802.3x hardware flow control?

  Read the article

• Excel data into PowerPoint slides

  - by nqw1

  I have already found some helpful sites but I'm still unable to do what I want. My Excel file contains few columns and multiple rows. All the data from one row would be in one slide but data from different cells in that one row should go to a specific elements in PP slide. At first, is it possible to export data from an Excel cell into a specific text box in PP? For example, I would like to have all data from the first column of each row go to a Text box 1. Let's say I have 100 rows so I would have 100 slides and each slide would have Text bow 1 with correct data. Text box of slide 66 would have data from the first column of row 66. Then all data from the second column of each row would go to a text bow 2 and so on. I tried to do some macros with bad success. I also tried to use Word outlines and export them into PP (New slide - Slides from Outline) but there seems to be a bug since I got 250 pages of gibberish. I had only two paragraphs and both had one word. First paragraph used Heading 1 style and second paragraph used Normal style. Sites what I have found, use VB and/or some other programming language to create slides from Excel sheets. I have tried to add those VB codes into my macros but none of them hasn't worked so far. Probably I just don't know how to use them correctly :) Here's some helpful sites: VBA: Create PowerPoint Slide for Each Row in Excel Workbook Creating a Presentation Report Based on Data Question in Stackoverflow I use Office 2011 on Mac. Any help would be appreciated!

  Read the article

• 2 nics. 2 Defaults Gateways

  - by andre.dias

  Here is my scenario: i have this server with 2 nics, each one with different IPs, connected to differents routers. Almost everything is configured whe way i need. Traffic coming from eth0 exits using eth0, traffic coming from eth1 exits using eth1. And there is a default gateway configured. $route: default IP 0.0.0.0 UG 0 0 0 eth0 With this configuration, the traffic generated in the server is going out using eth0 (lynx www.google.com for example). The problem is: the Internet link from eth0 went down today. The traffic coming from eth1 was ok...no problem. But the traffic generated in the server was a problem...the default gateway was out...no access do the Internet anymore (no more lynx www.google.com) So i added a new default gateway configuration, pointing to eth1. For 30 minutes i kept that way...2 default gateways, but just one was "working"...and everything was working just fine. But then i removed de eth0 gateway entry because, well, 2 default gateways is kind of weird. My question: is there any problem on keeping these 2 default gateways, one for each? So i don´t need to do nothing when one link go down again? $route: default IP1 0.0.0.0 UG 0 0 0 eth0 default IP2 0.0.0.0 UG 0 0 0 eth1

  Read the article

• Disaster After Removing Two HDD From LaCie RAID 0 Case

  - by John

  This is the second time this has happened. I own a LaCie IDE RAID 0 Enclosure and the RAID went bad. The system gave me a warning that the data could be read from the RAID but that nothing could be written, and to remove the data ASAP. I did that and erased and reinitialized the RAID. System reported it was fine, no issues. I wrote to the RAID again and the system reported the same issue. So, I removed the drives and tested them individually thinking one must have gone bad. Sure enough, one HDD reported all bad blocks, every single one after the Master Boot Record. I didn't think much about it because of the age of the drives, 5 years old. So, I bought two new drives plugged them in and started up the RAID again. Exactly the same thing happened. All was fine after initializing the RAID and then the next day after powering on the RAID the exact same issue. The HDD sitting in the same position as the first "bad" HDD reported all bad blocks. Obviously, this is an issue with LaCie's bridge board not with the drives. No utility I have used has been able to bring this HDD back to life. I thought I would just copy the MBR from the good drive to the new one using a sector editor but am hesitant. Is it possible the firmware on the HDD has been corrupted by the LaCie bridge board?? What else could be the cause of such an issue? How can I fix this drive?

  Read the article

• vagrant and puppet security for ssl certificates

  - by Sirex

  I'm pretty new to vagrant, would someone who knows more about it (and puppet) be able to explain how vagrant deals with the ssl certs needed when making vagrant testing machines that are processing the same node definition as the real production machines ? I run puppet in master / client mode, and I wish to spin up a vagrant version of my puppet production nodes, primarily to test new puppet code against. If my production machine is, say, sql.domain.com I spin up a vagrant machine of, say, sql.vagrant.domain.com. In the vagrant file I then use the puppet_server provisioner, and give a puppet.puppet_node entry of “sql.domain.com” to it gets the same puppet node definition. On the puppet server I use a regex of something like /*.sql.domain.com/ on that node entry so that both the vagrant machine and the real one get that node entry on the puppet server. Finally, I enable auto-signing for *.vagrant.domain.com in puppet's autosign.conf, so the vagrant machine gets signed. So far, so good... However: If one machine on my network gets rooted, say, unimportant.domain.com, what's to stop the attacker changing the hostname on that machine to sql.vagrant.domain.com, deleting the old puppet ssl cert off of it and then re-run puppet with a given node name of sql.domain.com ? The new ssl cert would be autosigned by puppet, match the node name regex, and then this hacked node would get all the juicy information intended for the sql machine ?! One solution I can think of is to avoid autosigning, and put the known puppet ssl cert for the real production machine into the vagrant shared directory, and then have a vagrant ssh job move it into place. The downside of this is I end up with all my ssl certs for each production machine sitting in one git repo (my vagrant repo) and thereby on each developer's machine – which may or may not be an issue, but it dosen't sound like the right way of doing this. tl;dr: How do other people deal with vagrant & puppet ssl certificates for development or testing clones of production machines ?

  Read the article

• Virtual host config issues in osx 10.7 server app

  - by Benno

  I have two mac mini lion servers setup to run as production and staging machines. My sysadmin decided on these machines over the previous CentOS we had because it had an "interface" to be able to manage it, rather than just the terminal. To be honest, I prefer the terminal. My problem is, the mac osx 10.7 server.app seems to be having issues with the creation of virtual hosts in the 'Web' section. It seems VERY touchy. For example, I cannot create a http virtual host first. I have to create a https host first with a unique dns name 9e..g vuly6), then create the http host with a different dns name to the first (e.g. www), or it appears to override it the first one, even though one is ssl and one is non-ssl. Further, it seems to override perfectly good configurations at random. For example, the default sites directory is usually /Users/default/Sites/Customsites or something, but sometimes when I load the server.app it changes to /var/empty. Also, if I change or add extra virtual hosts after the first one or two, it starts to mess up and the first two virtual hosts start having issues. Has anyone had any experience with setting up virtual hosts via this app? Am I able to manually create these virtual hosts, without using the app, and without the app overriding my settings when I restart apache?

  Read the article

• Downmix ALL SYSTEM audio to mono - Windows 7

  - by Mike K.

  I'm deaf in one ear and want to use my headphones when playing a game and talking with my friends on Skype/TS/Mumble/etc while also sometimes listening to music. I need ALL my system audio to be downmixed to mono so that my ONE hearing ear gets ALL audio channels instead of split stereo audio. No, none of the other similar questions on superuser have a solution. My headphone properties does not have a 'Mono' option, I don't have a 'Headphone Virtualization' option, and my Realtek HD audio driver software doesn't have these options either (driver was updated 11/14/2012). Don't even talk about setting the balance of one side of the headphones to 0. You're not paying attention if you suggest that. JACK and Virtual Audio Cable didn't work. It's possible I configured them wrong, but I followed the steps I found in related questions and still got split stereo out. TL;DR I need a viable, working, software solution (I say software because I have a USB headset) for forcing ALL system audio to mono so that I can hear literally everything through the one earpiece. Thanks!

  Read the article

< Previous Page | 361 362 363 364 365 366 367 368 369 370 371 372  | Next Page >