Search Results

Search found 11364 results on 455 pages for 'port blocking'.

Page 365/455 | < Previous Page | 361 362 363 364 365 366 367 368 369 370 371 372  | Next Page >

• Why wifi doesn't work in this case?

  - by xRobot

  I have a brand new notebook where I have installed Windows 7 and Ubuntu 12.04 LTS 64bit in dual boot. In windows 7 wifi works but in Ubuntu not. Could you help me please ? iwconfig lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=20 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off eth0 no wireless extensions. lshw -C network *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:01:00.0 logical name: eth0 version: 07 serial: b4:b5:1f:1b:9a:56 size: 10Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=rtl8168e-3_0.0.4 03/27/12 latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:41 ioport:3000(size=256) memory:c2404000-c2404fff memory:c2400000-c2403fff *-network description: Wireless interface product: Ralink corp. vendor: Ralink corp. physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 00 serial: 84:4b:f4:0a:3a:22 width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=rt2800pci driverversion=3.2.0-31-generic firmware=0.34 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:18 memory:c2500000-c250ffff lspci | grep -i net 01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 07) 02:00.0 Network controller: Ralink corp. Device 539a iwlist scan lo Interface doesn't support scanning. wlan0 Interface doesn't support scanning : Device or resource busy eth0 Interface doesn't support scanning. lsmod Module Size Used by rfcomm 47604 0 bnep 18281 2 bluetooth 180104 10 rfcomm,bnep parport_pc 32866 0 ppdev 17113 0 snd_hda_codec_hdmi 32474 1 snd_hda_codec_realtek 224173 1 joydev 17693 0 hp_wmi 18092 0 sparse_keymap 13890 1 hp_wmi snd_hda_intel 33773 3 snd_hda_codec 127706 3 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel snd_hwdep 13668 1 snd_hda_codec snd_pcm 97188 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec snd_seq_midi 13324 0 snd_rawmidi 30748 1 snd_seq_midi snd_seq_midi_event 14899 1 snd_seq_midi snd_seq 61896 2 snd_seq_midi,snd_seq_midi_event snd_timer 29990 2 snd_pcm,snd_seq snd_seq_device 14540 3 snd_seq_midi,snd_rawmidi,snd_seq psmouse 97362 0 snd 78855 16 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device arc4 12529 2 rt2800pci 18715 0 rt2800lib 58925 1 rt2800pci crc_ccitt 12667 1 rt2800lib rt2x00pci 14577 1 rt2800pci rt2x00lib 51144 3 rt2800pci,rt2800lib,rt2x00pci mac80211 506816 3 rt2800lib,rt2x00pci,rt2x00lib soundcore 15091 1 snd mac_hid 13253 0 uvcvideo 72627 0 videodev 98259 1 uvcvideo v4l2_compat_ioctl32 17128 1 videodev wmi 19256 1 hp_wmi i915 473240 3 cfg80211 205544 2 rt2x00lib,mac80211 eeprom_93cx6 12725 1 rt2800pci drm_kms_helper 46978 1 i915 drm 242038 4 i915,drm_kms_helper i2c_algo_bit 13423 1 i915 snd_page_alloc 18529 2 snd_hda_intel,snd_pcm mei 41616 0 serio_raw 13211 0 video 19596 1 i915 lp 17799 0 parport 46562 3 parport_pc,ppdev,lp usbhid 47199 0 hid 99559 1 usbhid r8169 62099 0 rfkill list: # rfkill list 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no 1: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: no

  Read the article

• sony vaio WLAN problem using 12.04

  - by Fredrik

  I'm unable to get my WLAN to work for my Sony Vaio model VPCF23C5E No problem connecting from windows, smartphones etc. $ sudo lshw -C network; lsb_release -a; uname -a; sudo rfkill list; dmesg | grep -i firm *-network description: Wireless interface product: AR9485 Wireless Network Adapter vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 01 serial: 64:27:37:92:99:0f width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list rom ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.2.0-29-generic firmware=N/A latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:16 memory:f7000000-f707ffff memory:f7080000-f708ffff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:05:00.0 logical name: eth0 version: 06 serial: f0:bf:97:dd:b2:bd size: 1Gbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8168e-1.fw ip=192.168.1.4 latency=0 link=yes multicast=yes port=MII speed=1Gbit/s resources: irq:50 ioport:9000(size=256) memory:e2104000-e2104fff memory:e2100000-e2103fff LSB Version: core-2.0-amd64:core-2.0-noarch:core-3.0-amd64:core-3.0-noarch:core-3.1-amd64:core-3.1-noarch:core-3.2-amd64:core-3.2-noarch:core-4.0-amd64:core-4.0-noarch Distributor ID: Ubuntu Description: Ubuntu 12.04.1 LTS Release: 12.04 Codename: precise Linux siriedit 3.2.0-29-generic #46-Ubuntu SMP Fri Jul 27 17:03:23 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux 1: phy0: Wireless LAN Soft blocked: no Hard blocked: no 2: hci0: Bluetooth Soft blocked: no Hard blocked: no [ 1.287449] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored [ 18.273582] [Firmware Bug]: ACPI(NGFX) defines _DOD but not _DOS Seen some proposed solution e.g. Wireless network cannot be enabled for Sony VAIO E series but answers there don't solve my problem... I'm out of ideas :-( What else can I check? update $ ifconfig -a eth0 Link encap:Ethernet HWaddr f0:bf:97:dd:b2:bd inet addr:192.168.1.4 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::f2bf:97ff:fedd:b2bd/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5072 errors:0 dropped:0 overruns:0 frame:0 TX packets:4444 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4568435 (4.5 MB) TX bytes:610624 (610.6 KB) Interrupt:50 Base address:0xc000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:1498 errors:0 dropped:0 overruns:0 frame:0 TX packets:1498 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:114156 (114.1 KB) TX bytes:114156 (114.1 KB) wlan0 Link encap:Ethernet HWaddr 64:27:37:92:99:0f inet addr:192.168.1.5 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::6627:37ff:fe92:990f/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1277 errors:0 dropped:0 overruns:0 frame:0 TX packets:472 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:483155 (483.1 KB) TX bytes:61031 (61.0 KB)

  Read the article

• How do I know if I am using Scrum methodologies?

  - by Jake

  When I first started at my current job, my purpose was to rewrite a massive excel-VBA workbook-application to C# Winforms because it was thought that the new C# app will fix all existing problems and have all the new features for a perfect world. If it were a direct port, in theory it would be easy as i just need to go through all the formulas, conditional formatting, validations, VBA etc. to understand it. However, that was not the case. Many of the new features are tightly dependant on business logic which I am unfamiliar with. As a solo programmer, the first year was spent solely on deciphering the excel workbook and writing the C# app. In theory, I had the business people to "help" me specify requirements, how GUI looks and work, and testing of the app etc; but in practice it is like a contant tsunami of feature creep. At the beginning of the second year I managed to convince the management that this is not going anywhere. I made them start from scratch with the excel-VBA. I have this "issue log" saved on the network, each time they found something they didn't like about the excel-VBA app, they will write it in there. I check the log daily and consolidate issues (in my mind) mainly into 2 groups: (1) requires massive change. (2) can be fixed in current version. For massive change issues, I make a copy of the latest excel-VBA and give it a new version number, then work on it whenever I can. For current version fixes, I make the changes in a few days to a week, and then immediately release it. I also ensure I update the same change in any in-progress massive change future versions. This has gone on for about 4 months and I feel it works great. I made many releases and solved many real issues, also understood the business logic more and more. However, my boss (non-IT trained) thinks what I am doing are just adhoc changes and that i am not looking at the "bigger picture". I am struggling to convince my boss that this works. So I hope to formalise my approach and maybe borrow a buzzword to confuse him. Incidentally, I read about Agile and SCRUM, about backlog and sprints. But it's all very vague to me still. QUESTION (finally): I want to tell him that this is SCRUM! But I want to hold my breath first and ask whether my current approach is considered SCRUM or SCRUM-like? How can I make it more SCRUM-like? Note that I have only myself, there's no project leader or teams.

  Read the article

• Unable to make the session state request to the session state server.

  - by Angry_IT_Guru

  For about 4-5 months now, I seem to be having this sporadic issue--mainly during our busiest time of the day between 10:30-11:45AM, where all my Windows 2003 web servers in a Microsoft NLB cluster start throwing session state server errors. A sample error is below. System.Web.HttpException: Unable to make the session state request to the session state server. Please ensure that the ASP.NET State service is started and that the client and server ports are the same. If the server is on a remote machine, please ensure that it accepts remote requests by checking the value of HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\aspnet_state\Parameters\AllowRemoteConnection. If the server is on the local machine, and if the before mentioned registry value does not exist or is set to 0, then the state server connection string must use either 'localhost' or '127.0.0.1' as the server name. at System.Web.SessionState.OutOfProcSessionStateStore.MakeRequest(StateProtocolVerb verb, String id, StateProtocolExclusive exclusiveAccess, Int32 extraFlags, Int32 timeout, Int32 lockCookie, Byte[] buf, Int32 cb, Int32 networkTimeout, SessionNDMakeRequestResults& results) at System.Web.SessionState.OutOfProcSessionStateStore.SetAndReleaseItemExclusive(HttpContext context, String id, SessionStateStoreData item, Object lockId, Boolean newItem) at System.Web.SessionState.SessionStateModule.OnReleaseState(Object source, EventArgs eventArgs) at System.Web.HttpApplication.SyncEventExecutionStep.System.Web.HttpApplication.IExecutionStep.Execute() at System.Web.HttpApplication.ExecuteStep(IExecutionStep step, Boolean& completedSynchronously) Now I'm using ASP.NET State service on a centralized back-end Windows 2003 server that all servers communicate to. I was originally using SQL Server state for a couple years as well prior to having this issue. The problem with SQL wqas that when the issue occurred, it created a blocking situation which essentially impacted all users across all servers. The product company recommended that I use the standard ASP.NET State service as that was what they technically supported. Why this would make a difference is beyond me -- but I had no choice but to try it! I have attempted to create multiple application pools, adding additional servers, chaning TCP/IP timeout from 20 to 30 seconds, and even calling Microsoft ASP.NET product support, with very little success. I even recommended that they review whether they are using read-only session state instead of read/write per page request -- as I understand that this basically causes every page to make round-trips to state server even if state isn't being used on the page. Unfortunately, the application is developed by our product company and they insist that it is something with my environment because other clients do not have these sort of issues. However, I've talked to other clients and they tell me when they've seen issues like they, they've basically had to create another web farm. This issue almost seems like I've simply reached some architectural limit within the application... Microsoft's position on the issue is that the session state needs to be reduced and the returncode being reported back from the state server indicates buffers are full. To better understand the scope of issues (rather than wait for customers to call and complain), I installed ELMAH and configured it to send me e-mails when unhandled exceptions occur. I basically get 500-1000 e-mails during the time period of high activity! If any one has any other ideas I could try or better ways to troubleshoot, I'd appreciate it.

  Read the article

• Software Architecture Analysis Method (SAAM)

  Software Architecture Analysis Method (SAAM) is a methodology used to determine how specific application quality attributes were achieved and how possible changes in the future will affect quality attributes based on hypothetical cases studies. Common quality attributes that can be utilized by this methodology include modifiability, robustness, portability, and extensibility. Quality Attribute: Application Modifiability The Modifiability quality attribute refers to how easy it changing the system in the future will be. This to me is a very open-ended attribute because a business could decide to transform a Point of Sale (POS) system in to a Lead Tracking system overnight. (Yes, this did actually happen to me) In order for SAAM to be properly applied for checking this attribute specific hypothetical case studies need to be created and review for the modifiability attribute due to the fact that various scenarios would return various results based on the amount of changes. In the case of the POS change out a payment gateway or adding an additional payment would have scored very high in comparison to changing the system over to a lead management system. I personally would evaluate this quality attribute based on the S.O.I.L.D Principles of software design. I have found from my experience the use of S.O.I.L.D in software design allows for the adoption of changes within a system. Quality Attribute: Application Robustness The Robustness quality attribute refers to how an application handles the unexpected. The unexpected can be defined but is not limited to anything not anticipated in the originating design of the system. For example: Bad Data, Limited to no network connectivity, invalid permissions, or any unexpected application exceptions. I would personally evaluate this quality attribute based on how the system handled the exceptions. Robustness Considerations Did the system stop or did it handle the unexpected error? Did the system log the unexpected error for future debugging? What message did the user receive about the error? Quality Attribute: Application Portability The Portability quality attribute refers to the ease of porting an application to run in a new operating system or device. For example, It is much easier to alter an ASP.net website to be accessible by a PC, Mac, IPhone, Android Phone, Mini PC, or Table in comparison to desktop application written in VB.net because a lot more work would be involved to get the desktop app to the point where it would be viable to port the application over to the various environments and devices. I would personally evaluate this quality attribute based on each new environment for which the hypothetical case study identifies. I would pay particular attention to the following items. Portability Considerations Hardware Dependencies Operating System Dependencies Data Source Dependencies Network Dependencies and Availabilities  Quality Attribute: Application Extensibility The Extensibility quality attribute refers to the ease of adding new features to an existing application without impacting existing functionality. I would personally evaluate this quality attribute based on each new environment for the following Extensibility  Considerations Hard coded Variables versus Configurable variables Application Documentation (External Documents and Codebase Documentation.) The use of Solid Design Principles

  Read the article

• Exalytics OBI11g Partner Training 3-day hands-on Workshops

  - by Mike.Hallett(at)Oracle-BI&EPM

  These FREE to OPN Partners hands-on workshops highlight both the hardware and software components that are engineered to work together to deliver Oracle Exalytics - an optimized version of the industry-leading Oracle TimesTen In-Memory Database with analytic extensions, a highly scalable Oracle server designed specifically for in-memory business intelligence, and Oracle's proven Business Intelligence Foundation (OBI 11g v 11.1.1.6 and Essbase) with enhanced visualization capabilities and performance optimizations. Priority will be given to Partner individuals who have passed or scheduled to take the Oracle Business Intelligence Foundation Suite 11g Essentials (1Z1-591) exam, and to Partners who have purchased an Exalytics for their own data centres to demonstrate it to their clients. Topics covered will include: Exalytics Architectural Overview Upgrade and Lifecycle Management Times Ten for Exalytics Summary Advisor Utility Essbase and EPM System on Exalytics Dashboard and Analysis Interactions OBIEE 11.1.1.6 Features and Advanced Topics After taking this course, you will be well prepared to architect, build, demo, and implement an end-to-end Exalytics solution.You will also be able to extend your current analytical and enterprise performance management application implementations with numerous Oracle technologies specifically enhanced to take advantage of the compute capacity and in-memory capabilities of Oracle Exalytics. Prerequisites Experience and understanding of OBIEE 11g is required ·       Previous attendance of Oracle Business Intelligence Foundation Suite Workshop or BIEE 11g Introduction Workshop is highly recommended, and priority will be given to Partner individuals who have passed or scheduled to take the Oracle Business Intelligence Foundation Suite 11g Essentials (1Z1-591) exam. Good understanding of data warehousing and data modelling for reporting and analysis purpose.  Strong experience with database technologies preferred Attendee to provide their own laptops which must meet the following minimum hardware/software requirements: Hardware Minimum 8GB RAM 60 GB free disk space (includes staging) USB 2.0 port (at least one available) It is strongly recommended that you bring a mouse. You will be working in a development environment and using the mouse heavily. Software One of the following operating systems: 64-bit Windows host/laptop OS 64-bit host/laptop OS with a Windows VM (XP, Server, or Win 7, BIC2g, etc.) Internet Explorer 7.x/8.x or Firefox 3.5.x WINRAR or 7ziputility to unzip workshop files: Download-able from http://www.win-rar.com/download.html Download-able from http://www.7zip.com/ Oracle VirtualBox 4.0.2 or higher Downloadable from http://www.virtualbox.org/wiki/Downloads CPU virtualization mode needs to be enabled. We will provide guidance on the day of the workshop.  Attendees will be given a VirtualBox image containing a pre-installed Oracle Exalytics environment. Register Here for 3-day Workshops: 11-Dec-12 Birmingham UK 29-Jan-13 Utrecht NL 12-Feb-13 Frankfurt Germany 12-Mar-13 Moscow Russia

  Read the article

• Still prompted for a password after adding SSH public key to a server

  - by Nathan Arthur

  I'm attempting to setup a git repository on my Dreamhost web server by following the "Setup: For the Impatient" instructions here. I'm having difficulty setting up public key access to the server. After successfully creating my public key, I ran the following command: cat ~/.ssh/[MY KEY].pub | ssh [USER]@[MACHINE] "mkdir ~/.ssh; cat >> ~/.ssh/authorized_keys" ...replacing the appropriate placeholders with the correct values. Everything seemed to go through fine. The server asked for my password, and, as far as I can tell, executed the command. There is indeed a ~/.ssh/authorized_keys file on the server. The problem: When I try to SSH into the server, it still asks for my password. My understanding is that it shouldn't be asking for my password anymore. What am I missing? EDIT: SSH -v Log: Macbook:~ michaeleckert$ ssh -v [USER]@[SERVER URL] OpenSSH_6.2p2, OSSLShim 0.9.8r 8 Dec 2011 debug1: Reading configuration data /etc/ssh_config debug1: /etc/ssh_config line 20: Applying options for * debug1: /etc/ssh_config line 53: Applying options for * debug1: Connecting to [SERVER URL] [[SERVER IP]] port 22. debug1: Connection established. debug1: identity file /Users/michaeleckert/.ssh/id_rsa type -1 debug1: identity file /Users/michaeleckert/.ssh/id_rsa-cert type -1 debug1: identity file /Users/michaeleckert/.ssh/id_dsa type -1 debug1: identity file /Users/michaeleckert/.ssh/id_dsa-cert type -1 debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_6.2 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.5p1 Debian-6+squeeze3 debug1: match: OpenSSH_5.5p1 Debian-6+squeeze3 pat OpenSSH_5* debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-ctr hmac-md5 none debug1: kex: client->server aes128-ctr hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Server host key: RSA [STRING OF NUMBERS AND LETTERS SEPARATED BY SEMI-COLONS] debug1: Host ‘[SERVER URL]' is known and matches the RSA host key. debug1: Found key in /Users/michaeleckert/.ssh/known_hosts:2 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: Roaming not allowed by server debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey,password debug1: Next authentication method: publickey debug1: Trying private key: /Users/michaeleckert/.ssh/id_rsa debug1: Trying private key: /Users/michaeleckert/.ssh/id_dsa debug1: Next authentication method: password [USER]@[SERVER URL]'s password: debug1: Authentication succeeded (password). Authenticated to [SERVER URL] ([[SERVER IP]]:22). debug1: channel 0: new [client-session] debug1: Requesting [email protected] debug1: Entering interactive session. debug1: Sending environment. debug1: Sending env LANG = en_US.UTF-8 Welcome to [SERVER URL] Any malicious and/or unauthorized activity is strictly forbidden. All activity may be logged by DreamHost Web Hosting. Last login: Sun Nov 3 12:04:21 2013 from [MY IP] [[SERVER NAME]]$

  Read the article

• Cablemodem (SBG6580) firewall denying some outbound traffic? Why? Not configured [migrated]

  - by lairdb

  I finally got around to turning the syslog on for my cablemodem (Motorola Surfboard SBG6580) and I'm seeing about the expected amount of inbound attackage being blocked... 2014-05-30 21:59:02 Local0.Alert 192.168.111.1 May 31 04:58:56 2014 SYSLOG[0]: [Host 192.168.111.1] UDP 12.230.209.198,4500 --> 66.27.xx.xx,61459 DENY:Firewall interface [IP Fragmented Packet] attack 2014-05-30 21:59:02 Local0.Alert 192.168.111.1 May 31 04:58:56 2014 SYSLOG[0]: [Host 192.168.111.1] TCP 17.172.232.109,5223 --> 66.27.xx.xx,53814 DENY:Firewall interface access request 2014-05-30 21:59:02 Local0.Alert 192.168.111.1 May 31 04:58:57 2014 SYSLOG[0]: [Host 192.168.111.1] UDP 12.230.209.198,443 --> 66.27.xx.xx,53385 DENY: Firewall interface [IP Fragmented Packet] attack 2014-05-30 21:59:02 Local0.Alert 192.168.111.1 May 31 04:58:57 2014 SYSLOG[0]: [Host 192.168.111.1] UDP 12.230.209.198,4500 --> 66.27.xx.xx,61459 DENY:Firewall interface [IP Fragmented Packet] attack 2014-05-30 21:59:10 Local0.Alert 192.168.111.1 May 31 04:59:04 2014 SYSLOG[0]: [Host 192.168.111.1] UDP 12.230.209.198,443 --> 66.27.xx.xx,59960 DENY: Firewall interface [IP Fragmented Packet] attack 2014-05-30 21:59:10 Local0.Alert 192.168.111.1 May 31 04:59:04 2014 SYSLOG[0]: [Host 192.168.111.1] UDP 12.230.209.198,4500 --> 66.27.xx.xx,61459 DENY:Firewall interface [IP Fragmented Packet] attack ...and that's great. (Sad, but great.) But I'm also seeing a HUGE amount of what appears to be denied outbound connectivity: 2014-05-30 16:30:10 Local0.Alert 192.168.111.1 May 30 23:30:04 2014 SYSLOG[0]: [Host 192.168.111.1] TCP 192.168.111.100,58969 --> 38.81.66.127,443 DENY: Inbound or outbound access request 2014-05-30 16:30:10 Local0.Alert 192.168.111.1 May 30 23:30:04 2014 SYSLOG[0]: [Host 192.168.111.1] TCP 192.168.111.100,58969 --> 38.81.66.127,443 DENY: Inbound or outbound access request 2014-05-30 16:30:10 Local0.Alert 192.168.111.1 May 30 23:30:04 2014 SYSLOG[0]: [Host 192.168.111.1] TCP 192.168.111.100,58965 --> 162.222.41.13,443 DENY: Inbound or outbound access request 2014-05-30 16:30:10 Local0.Alert 192.168.111.1 May 30 23:30:04 2014 SYSLOG[0]: [Host 192.168.111.1] TCP 192.168.111.100,58965 --> 162.222.41.13,443 DENY: Inbound or outbound access request 2014-05-30 16:30:10 Local0.Alert 192.168.111.1 May 30 23:30:04 2014 SYSLOG[0]: [Host 192.168.111.1] TCP 192.168.111.100,58964 --> 38.81.66.179,443 DENY: Inbound or outbound access request 2014-05-30 16:30:10 Local0.Alert 192.168.111.1 May 30 23:30:04 2014 SYSLOG[0]: [Host 192.168.111.1] TCP 192.168.111.100,58964 --> 38.81.66.179,443 DENY: Inbound or outbound access request ...and Spot checking suggests that it's all legitimate traffic (Opening connections to CrashPlan, etc.), I have no restrictions configured in the modem; I don't see why it should be blocking anything. Am I misreading the log entry, and it's not actually being denied? (Seems unlikely.) Is the ISP (TWC) pushing deny tables that are not exposed in the UI? (Tinfoil hat too tight.) I'm confused. (The good news, such as it is, is that AFAIK I'm not experiencing any actual issues... but maybe I am; tough to tell.) Thanks.

  Read the article

• How does the Cloud compare to Colocation? And development too

  - by David

  Currently I/we run a SaaS web application where each subscriber has their own physical instance of the application in addition to their own database. The setup has each web application instance deployed on two different IIS boxes both for load-balancing and redundancy (the machines have their Windows Update install times 12 hours apart, for example). Databases are mirrored on two different SQL Server 2012 machines with AlwaysOn for uptime. I don't make use of SQL Server clustering (as it doesn't provide storage-level failover: we don't have a shared storage box). Because it's a Windows setup it means there are two Domain Controllers (we cheat: they're both Mac Minis, 17W each, which keeps our colo power costs low). Finally there's also an Exchange server (Mailbox, Hub Transport and Client Access). One of the SQL Servers also doubles-up as an Exchange Hub Transport. Running costs are about $700 a month for our quarter-rack colocation (which includes power and peering/transfer), then there's about $150 a month for SPLA licensing, so $850 a month in total. Then there's the hard-to-quantify cost of administration, but I reckon I spend a couple of hours a week checking-in on the servers: reviewing event logs, etc. I keep getting bombarded by ads and manufactured news stories about how great "the cloud" is. Back in 2008 when the cloud was taking off I was reading up about the proper "cloud" services like Google AppEngine, where you write in Python against Google's API and that's how they scale your application across servers and also use their database provider for scaling storage. Simple enough to understand. Then came along Amazon, and I understand how Amazon Storage works, but I'm not sure how Amazon Compute works: web application pages don't take much CPU time to compute, how do you even quantify usage anyway? Finally, RackSpace gets in the act and now I'm really confused. RackSpace advertise "Cloud" SQL Server 2012 available for about "$0.70 per hour", going by how they advertise it I thought the "hour" meant the sum of CPU time, IO blocking time, maybe time spent transferring data, so for a low-intensity application that works out pretty cheap then? Nope. I went on to a Sales Chat window and spoke to one of their advisors. They told me the $0.70/hour was actually for every hour the SQL Server is running... but who wants a SQL Server for only a few hours? You're going to need it available 24 hours a day for months on end. $0.70 * 24 * 31 works out at $520 a month, which is rediculously expensive for SQL Server. An SPLA license for SQL Server is only $50 a month or so. That $520 a month does not include "fanatical support", and you also need to stack on top the costs of the host Windows server instance too. From what I can tell, Rackspace's "Cloud" products seem like like an cynical rebranding of an overpriced VPS service, but priced by the hour. I have the same confusion about Windows Azure which uses similar terms to describe the products available, but I think that's because Azure offers both traditional shared webhosting in addition to their own APIs you can target for scalable applications.

  Read the article

• External 1TB WD USB 3.0 HDD is not detecting. Working perfectly find in Windows

  - by Yathi

  My 1TB USB 3.0 was working fine earlier in Ubuntu as well as Windows. But lately it is not at all being detected in Ubuntu. It still works fine in Windows. I did update my Ubuntu to 12.10 but I am not sure if that caused the issue. When I connect my HDD and run dmesg | tail: [ 47.804676] usb 4-3: >Device not responding to set address. [ 48.008575] usb 4-3: >Device not responding to set address. [ 48.212421] usb 4-3: >device not accepting address 9, error -71 [ 48.324451] usb 4-3: >Device not responding to set address. [ 48.528340] usb 4-3: >Device not responding to set address. [ 48.732165] usb 4-3: >device not accepting address 10, error -71 [ 48.844138] usb 4-3: >Device not responding to set address. [ 49.048179] usb 4-3: >Device not responding to set address. [ 49.251881] usb 4-3: >device not accepting address 11, error -71 [ 49.251907] hub 4-0:1.0: >unable to enumerate USB device on port 3 The output of sudo fdisk -l is : Disk /dev/sda: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x00030cde Device Boot Start End Blocks Id System /dev/sda1 2048 1332981759 666489856 83 Linux /dev/sda2 1332981760 1953523711 310270976 5 Extended /dev/sda5 1332983808 1349365759 8190976 82 Linux swap / Solaris /dev/sda6 1349367808 1953523711 302077952 7 HPFS/NTFS/exFAT Disk /dev/sdb: 120.0 GB, 120034123776 bytes 255 heads, 63 sectors/track, 14593 cylinders, total 234441648 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000a2519 Device Boot Start End Blocks Id System /dev/sdb1 * 2048 103368703 51683328 7 HPFS/NTFS/exFAT /dev/sdb2 103368704 154568703 25600000 83 Linux /dev/sdb3 154568704 234440703 39936000 7 HPFS/NTFS/exFAT /dev/sda and /dev/sdb are my 2 internal HDDs. But the external one which should be /dev/sdc is not even being shown though it is connected and the LED on the HDD is glowing. Someone had suggested adding blacklist uas to /etc/modprobe.d/blacklist.conf. Tried that as well. But still not working. Can someone help me out.

  Read the article

• SSTP client disconnects shortly after successfully connected to VPN

  - by Eran Betzalel

  I'm successfully authenticating and connecting to a SSTP VPN (on windows 2008) from my windows 7 machine, but for some reason, the connection is disconnected about a 1-2 seconds after it's established. I've done the following: Defined a SSTP VPN on my windows server 2008. Defined the same machine as CA. Issued the needed certificates and published them on the client. I'm currently testing this VPN inside my LAN so all the needed ports are opened. Here are the event log entries when trying to connect: Error Log (Client): The user HOME\User dialed a connection named Home VPN which has terminated. The reason code returned on termination is 829. Error Log (Server-VPN): The user HOME\User connected on port VPN0-0 on 7/27/2012 at 1:57 AM and disconnected on 7/27/2012 at 1:57 AM. The user was active for 0 minutes 0 seconds. 312 bytes were sent and 4528 bytes were received. The reason for disconnecting was user request. What would be the issue? How can I resolve or debug it? UPDATE: I've found an event log (Log=System, Source=RasSstp) message on the windows 7 machine that tries to connect to the VPN: The SSTP-based VPN connection to the remote access server was terminated because of a security check failure. Security settings on the remote access server do not match settings on this computer. Contact the system administrator of the remote access server and relay the following information: SHA1 Certificate Hash: 065D681...520375552F SHA256 Certificate Hash: 18DED363...EEEE28CFD00

  Read the article

• virtualbox installing iso Error "could not find a valid v7 on sda"

  - by MountainX

  I decided to try this suggestion to install Android x86 on Virtual Box. I'm following those steps and I'm at #4. I used the android-x86-4.0-RC1-amd_brazos.iso (because I have a ThinkPad that this might be compatible with and it seemed as good as any of the other choices...) I'm getting an endless series of errors: .[numbers] VFS: could not find a valid v7 on sda. .[numbers] VFS: could not find a valid v7 on sda. repeating... For storage, I made a VDI image sized at 4.0 GB (dynamically allocated) attached on SATA Port 0. Background and more details: I'm running Kubuntu 12.04. I installed VirtualBox 4.1.12 after adding deb http://download.virtualbox.org/virtualbox/debian precise contrib to my sources. EDIT: Now I'm wondering if I installed the right package. I verified that I'm running 4.1.12. But I installed it with apt-get install virtualbox instead of the recommended apt-get install virtualbox-4.1. I checked just now and see this: apt-cache search virtualbox virtualbox - x86 virtualization solution - base binaries virtualbox-4.1 - Oracle VM VirtualBox But when I run VirtualBox, I get the Oracle VM VirtualBox Manager version 4.1.12, so I think I'm OK. I did see one minor issue (possibly related to this question) when installing VB, but in my case I don't think it is actually an error at all: * No suitable module for running kernel found [fail] invoke-rc.d: initscript virtualbox, action "restart" failed. VirtualBox installed and seems to be running fine. I just can't get the ISO image to install. The error is as shown above.

  Read the article

• ssh + tinyproxy: poor performance

  - by Paul

  I am currently in China and I would like to still visit some blocked websites (facebook, youtube). I have VPS in the USA and I have installed tinyproxy on it. I log in on my VPS with SSH port-forwarding and I have configured my browser appropriately. Everything works more or less: I can surf to those websites but everything is inusually slow and sometimes data transfer stops abruptly. This probably has to do with the fact that I see some errors in my shell on the VPS like : channel 6: open failed: connect failed: Also in the log-file of tinyproxy I see some bad things: ERROR Sep 06 14:52:14 [28150]: getpeer_information: getpeername() error: Transport endpoint is not connected ERROR Sep 06 14:52:15 [28153]: writebuff: write() error "Connection reset by peer" on file descriptor 7 ERROR Sep 06 14:52:15 [28168]: readbuff: recv() error "Connection reset by peer" on file descriptor 7 ERROR Sep 06 14:52:15 [28151]: readbuff: recv() error "Connection reset by peer" on file descriptor 7 ERROR Sep 06 14:52:15 [28143]: readbuff: recv() error "Connection reset by peer" on file descriptor 7 ERROR Sep 06 14:52:17 [28147]: writebuff: write() error "Connection reset by peer" on file descriptor 7 ERROR Sep 06 14:52:23 [28137]: writebuff: write() error "Connection reset by peer" on file descriptor 7 ERROR Sep 06 14:52:26 [28168]: getpeer_information: getpeername() error: Transport endpoint is not connected ERROR Sep 06 14:52:27 [28186]: read_request_line: Client (file descriptor: 7) closed socket before read. ERROR Sep 06 14:52:31 [28160]: getpeer_information: getpeername() error: Transport endpoint is not connected

  Read the article

• Request Entity Too Large error while uploading files of more than 128KB over SSL

  - by tushar

  We have a web portal setup on Java spring framework. It running on tomcat app server. Portal is served through apache web server connected to tomcat through JK connector. Entire portal is HTTPS enabled using 443 port of apache. Apache version is : Apache/2.4.2 (Unix). it is the latest stable version of apache web server. Whenever we try to upload files more than 128 KB into the portal, We are facing 413 error: Request Entity Too Large The requested resource /teamleadchoachingtracking/doFileUpload does not allow request data with POST requests, or the amount of data provided in the request exceeds the capacity limit. In the apache error log we get the following errors: AH02018: request body exceeds maximum size (131072) for SSL buffer AH02257: could not buffer message body to allow SSL renegotiation to proceed We did search over google and there were suggestions to put SSLRenegBufferSize as some high value like 10MB. Based on these suggestions, we had put the following entry in virtualhost section of httpd config file: SSLRenegBufferSize 10486000 But still the error persists. Also we have specified SSLVerifyClient none, but still renegotiation is happening. This is a very inconsistent and frustrating error. Any help will be highly appreciated. Many thanks in advance.

  Read the article

• Teamcity build agent gives 504 gateway timeout

  - by Anthony

  I have a new teamcity build agent machine, which when started up tries to connect to the build server and fails. It never shows up in the connected, disconnected or unauthorised agents tabs of the build server web interface. The logs on the build agent show that it fails to connect with a 504 gateway timeout. This is from teamcity-agent.log [2012-09-04 15:34:59,776] INFO - buildServer.AGENT.registration - Registering on server http://10.0.10.16, AgentDetails{Name='my-local', AgentId=null, BuildId=null, AgentOwnAddress='10.0.1.14', AlternativeAddresses=[10.0.10.32], Port=8080, Version='21424', PluginsVersion='21424-md5-somechecksum', AvailableRunners=[ABunchOfPlugins], AvailableVcs=[SomeRunners], AuthorizationToken='sometoken'} [2012-09-04 15:35:53,606] WARN - buildServer.AGENT.registration - Call http://10.0.10.16/RPC2 buildServer.registerAgent3: org.apache.xmlrpc.XmlRpcClientException: Server returned incorrect status code: 504 Gateway Time-out [2012-09-04 15:35:53,606] WARN - buildServer.AGENT.registration - Connection to TeamCity server is probably lost. Will be trying to restore it. Take a look at logs/teamcity-agent.log for details (unless you're using custom logging). (I have edited some identifying data out of this log excerpt) But I can reach the build server. In fact, tracert shows that it is very nearby. Tracing route to TEAMCITYSERVER [10.0.10.16] over a maximum of 30 hops: 1 <1 ms <1 ms <1 ms 10.0.2.1 2 <1 ms <1 ms <1 ms TEAMCITYSERVER [10.0.10.16] Trace complete. I can see a teamcity login page if I hit http://10.0.10.16 in the browser. The teamcity service is logging in as the same (local administrator) account as I used to log in and test the network. The build agent is a windows 2008 server VM hosted on Ubuntu 12.04 under Oracle VirtualBox. I have disabled firewalls on both the Windows and Ubuntu machines. Other VMS with similar configuration can connect fine and do not report this error. What can possibly be preventing this connection?

  Read the article

• ssh key error - Permission denied (publickey,gssapi-keyex,gssapi-with-mic)

  - by user1963938

  Amazon Ec2 :: Redhat 6. 64 Bit I'm trying to follow the socks5 guidelines (http://www.catonmat.net/blog/linux-socks5-proxy/ ) to open a socks on one of our servers but unfortunately I got suck at step 1 . ssh -N -D 0.0.0.0:1080 localhost I get error Permission denied (publickey,gssapi-keyex,gssapi-with-mic). How do I fix it ? More debug info ssh -v -f -N -D 0.0.0.0:1080 localhost OpenSSH_5.3p1, OpenSSL 1.0.0-fips 29 Mar 2010 debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for * debug1: Connecting to localhost [127.0.0.1] port 22. debug1: Connection established. debug1: permanently_set_uid: 0/0 debug1: identity file /root/.ssh/identity type -1 debug1: identity file /root/.ssh/id_rsa type -1 debug1: identity file /root/.ssh/id_dsa type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.3 debug1: match: OpenSSH_5.3 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.3 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-ctr hmac-md5 none debug1: kex: client->server aes128-ctr hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Host 'localhost' is known and matches the RSA host key. debug1: Found key in /root/.ssh/known_hosts:1 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey,gssapi-keyex,gssapi-with-mic debug1: Next authentication method: gssapi-keyex debug1: No valid Key exchange context debug1: Next authentication method: gssapi-with-mic debug1: Unspecified GSS failure. Minor code may provide more information Credentials cache file '/tmp/krb5cc_0' not found debug1: Unspecified GSS failure. Minor code may provide more information Credentials cache file '/tmp/krb5cc_0' not found debug1: Unspecified GSS failure. Minor code may provide more information debug1: Unspecified GSS failure. Minor code may provide more information debug1: Next authentication method: publickey debug1: Trying private key: /root/.ssh/identity debug1: Trying private key: /root/.ssh/id_rsa debug1: Trying private key: /root/.ssh/id_dsa debug1: No more authentication methods to try. Permission denied (publickey,gssapi-keyex,gssapi-with-mic).

  Read the article

• xinetd 'connection reset by peer'

  - by ceejayoz

  I'm using percona-clustercheck (which comes with Percona's XtraDB Cluster packages) with xinetd and I'm getting an error when trying to curl the clustercheck service. /usr/bin/clustercheck: #!/bin/bash # # Script to make a proxy (ie HAProxy) capable of monitoring Percona XtraDB Cluster nodes properly # # Author: Olaf van Zandwijk <[email protected]> # Documentation and download: https://github.com/olafz/percona-clustercheck # # Based on the original script from Unai Rodriguez # MYSQL_USERNAME="clustercheckuser" MYSQL_PASSWORD="clustercheckpassword!" ERR_FILE="/dev/null" AVAILABLE_WHEN_DONOR=0 # # Perform the query to check the wsrep_local_state # WSREP_STATUS=`mysql --user=${MYSQL_USERNAME} --password=${MYSQL_PASSWORD} -e "SHOW STATUS LIKE 'wsrep_local_state';" 2>${ERR_FILE} | awk '{if (NR!=1){print $2}}' 2>${ERR_FILE}` if [[ "${WSREP_STATUS}" == "4" ]] || [[ "${WSREP_STATUS}" == "2" && ${AVAILABLE_WHEN_DONOR} == 1 ]] then # Percona XtraDB Cluster node local state is 'Synced' => return HTTP 200 /bin/echo -en "HTTP/1.1 200 OK\r\n" /bin/echo -en "Content-Type: text/plain\r\n" /bin/echo -en "\r\n" /bin/echo -en "Percona XtraDB Cluster Node is synced.\r\n" /bin/echo -en "\r\n" exit 0 else # Percona XtraDB Cluster node local state is not 'Synced' => return HTTP 503 /bin/echo -en "HTTP/1.1 503 Service Unavailable\r\n" /bin/echo -en "Content-Type: text/plain\r\n" /bin/echo -en "\r\n" /bin/echo -en "Percona XtraDB Cluster Node is not synced.\r\n" /bin/echo -en "\r\n" exit 1 fi /etc/xinetd.mysqlchk: # default: on # description: mysqlchk service mysqlchk { # this is a config for xinetd, place it in /etc/xinetd.d/ disable = no flags = REUSE socket_type = stream port = 9200 wait = no user = nobody server = /usr/bin/clustercheck log_on_failure += USERID only_from = 10.0.0.0/8 127.0.0.1 # recommended to put the IPs that need # to connect exclusively (security purposes) per_source = UNLIMITED } When attempting to curl the service, I get a valid response (HTTP 200, text) but a 'connection reset by peer' notice at the end: HTTP/1.1 200 OK Content-Type: text/plain Percona XtraDB Cluster Node is synced. curl: (56) Recv failure: Connection reset by peer Unfortunately, Amazon ELB appears to see this as a failed check, not a succeeded one. How can I get clustercheck to exit gracefully in a manner that curl doesn't see a connection failure?

  Read the article

• TortoiseSVN hangs in Windows Server 2012 Azure VM

  - by ZaijiaN

  Following @shanselman's article on remoting into an Azure VM for development, I spun up my own VS 2013 VM, and that image runs on WS 2012. Once I was able to remote in, I started installing all my dev tools, including Tortoise SVN 1.8.3 64bit. Things went south once I started attempting to check out code from my personal svn server. It would hang and freeze often, although sometimes it would work - I was able to partially check out projects, but I would get frequent connection time out errors. My personal svn server (VisualSVN 2.7.2) runs at home on a windows 7 machine, and I have a dyndns url pointing to it. I have also configured my router to passthrough all 443 traffic to the appropriate port on the server. I self-signed a cert and made sure it was imported into the VM cert store under trusted root authorities. I have no problems connecting to my svn server from 4-5 other computers & locations. From the Azure VM, in both IE and Chrome, I can access the repository web browser with no issues. There are no outbound firewall restrictions. I have installed other SVN add-ons for Visual Studio (AnkhSVN, VisualSVN) and attempted to connect with my svn server, with largely the same results - random and persistent connection issues (hangs/timeouts). I spun up a completely fresh WS 2008 Azure VM, and installed TortoiseSVN, and had the same results. So I'm at a loss as to what the problem is and how to fix it. Web searches on tortoisesvn and windows server issues doesn't yield any current or relevant information. At this point, i'm guessing that maybe some setting or configuration that MS Azure VM images is the culprit - although I should probably attempt to spin up my own local WS VM to rule out that it's a window server issue. Any thoughts? I hope I'm just missing something really obvious!

  Read the article

• Routing static IP traffic on a Comcast Business Class IP Gateway (SMCD3G-CCR)

  - by Jakobud

  We are in the process of replacing our firewall, which is currently the only thing connected to our Comcast Business Class modem. Comcast gives us 5 static IP addresses. Currently, all traffic to all 5 static IPs goes directly to the existing firewall. Eventually, obviously all traffic will goto the new firewall, once the old firewall is removed from the network. But in the meantime, as we will have two firewalls plugged into the same Comcast modem, I need to route certain traffic to the new firewall instead of the old one. The firewall switchover is going to be slow and gradual as I am testing it, so I can't simply unplug the existing firewall and plug in the new one. So my question is, how do I tell the modem to route all traffic that goes to a specific IP to goto the new firewall instead of the old one? I've logged into the web interface for the modem, but the available options aren't very clear. There is a 1-to-1 NAT option (which I can't seem to get the interface for it to work properly) but I also see a "Static Routing" section. I always understood Static Routing to refer to routing data within the LAN though, so I'm not sure if that's what I'm looking for or not. Keep in mind, I'm not looking to do simple port forwarding. I'm wanting 100% of traffic to certain public static IPs to go to the specified connected firewall (I'll deal with service policies there). The modem is an SMC SMCD3G-CCR and is labeled as a Comcast Business Class Business IP Gateway. Any help or direction would be greatly appreciated.

  Read the article

• Invalid keystore format with SSL in Tomcat 6

  - by strauberry

  I'm trying to setup SSL in my local Tomcat 6 installation. For this, I followed the official How-To doing the following: $JAVA_HOME/bin/keytool -genkey -v -keyalg RSA -alias tomcat -keypass changeit -storepass changeit $JAVA_HOME/bin/keytool -export -alias tomcat -storepass changeit -file /root/server.crt Then changing the $CATALINA_BASE/conf/server.xml, in-commenting this: <Connector port="8443" protocol="HTTP/1.1" SSLEnabled="true" maxThreads="150" scheme="https" secure="true" clientAuth="false" sslProtocol="TLS" keystoreFile="/root/.keystore" keystorePass="changeit" /> After starting Tomcat, I get this Exception: INFO: Initializing Coyote HTTP/1.1 on http-8080 30.06.2011 10:15:24 org.apache.tomcat.util.net.jsse.JSSESocketFactory getStore SCHWERWIEGEND: Failed to load keystore type JKS with path /root/.keystore due to Invalid keystore format java.io.IOException: Invalid keystore format at sun.security.provider.JavaKeyStore.engineLoad(JavaKeyStore.java:633) at sun.security.provider.JavaKeyStore$JKS.engineLoad(JavaKeyStore.java:38) at java.security.KeyStore.load(KeyStore.java:1185) When I look into the keystore with keytool -list I get root@host:~# $JAVA_HOME/bin/keytool -list Enter key store password: changeit Key store type: gkr Key store provider: GNU-CRYPTO Key store contains 1 entry(ies) Alias name: tomcat Creation timestamp: Donnerstag, 30. Juni 2011 - 10:13:40 MESZ Entry type: key-entry Certificate fingerprint (MD5): 6A:B9:...C:89:1C Obviously, the keystore types are different. How can I change the type and will this fix my problem? Thank you!

  Read the article

• ADFS 2.1 proxy trust establishment error

  - by Tommy Jakobsen

  I'm trying to install an ADFS proxy. In our intranet we have a ADFS 2.1 server running on Windows 2012 which is working fine. Now we're trying to deploy a proxy to this one for internet access, using Windows 2012 R2's Web Application Proxy. I'm getting the following error on the proxy server, event ID 393: Message : An error occurred while attempting to establish a trust relationship with the Federation Server. An error occurred when attempting to establish a trust relationship with the federation service. Error: Forbidden Context : DeploymentTask Status : Error I'm not getting any errors on the ADFS server. I've tried with different credentials. The ADFS service account, a domain administrator who is a member of the local administrators group on the ADFs server, and the local administrator account on the ADFS server. Same error message. Both port 80 and 443 is accessible from the proxy server to the internal ADFS server, and I can access the ADFS metadata endpoint from the proxy server. I'm using the same trusted SSL certificate (wildcard) on both machines. Do you have any ideas that can help me troubleshoot this problem?

  Read the article

• VLC (Server) re-stream Security Camera Feed

  - by Aaron

  I purchased a Swann Home Security DVR system and was hoping for some help on how to duplicate the streaming video on my server. In order to get their web view (streaming video in the browser) to work, I had to install the following plugins: HiDvrPlugin.dmg for mac. Hidvrocx.cab for Windows. I was originally thinking it was a sign of some form of DRM? Maybe. Maybe not. HTML wise, the following code is in the source of the safari version of the web view: <embed pluginspage="SurveilClient.dmg" width="10px" height="10px" type="application/x-scplugin" id="MacDiv" style="height: 592px; width: 720px; left: 278px; top: 61px; "> It seems to be the main display area. Using wireshark, I am able to see that the video stream is on port 9000. However, I have no idea what type of stream it is. I've tried opening it in VLC with no such luck. http://dvr_ip:9000 tcp://dvr_ip:9000 My hope was to do the following to redistribute the feed vlc dvr_ip:9000 --sout h264-version-on-localhost:3000 TLDR; Trying to re-distribute a stream from a security camera (can't tell the format) using vlc (re-distribute via h.264 / HTML5). Not sure how to accomplish this. Is it possible that the software has some type of DRM that only the plugins can decode?

  Read the article

• Configuring VirtualBox host only networking: OSX host, Ubuntu guest

  - by Greg K

  I have a Ubuntu guest configured with two interfaces, eth0 is using NAT and works fine, I can access the net. The second interface eth1 is set to host only networking and VirtualBox has created a vboxnet0 virtual adapter on the host. I've configured vboxnet0 in VirtualBox adapter settings with the following: ip 192.168.21.20 subnet 255.255.255.0 Once the VM guest is running, ifconfig on OSX has vboxnet0 setup as: vboxnet0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500 ether 0a:00:27:00:00:00 inet 192.168.21.20 netmask 0xffffff00 broadcast 192.168.21.255 In the guest, eth0 is set to use DHCP, I've statically assigned eth1 to 192.168.21.20 (is this a mistake?): auto eth1 iface eth1 inet static address 192.168.21.20 netmask 255.255.255.0 network 192.168.21.0 broadcast 192.168.21.255 gateway 192.168.21.1 There is no device on 192.168.21.1 - what should I set my gateway to? In the guest the routes look like so: Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.21.0 * 255.255.255.0 U 0 0 0 eth1 10.0.2.0 * 255.255.255.0 U 0 0 0 eth0 default 10.0.2.2 0.0.0.0 UG 100 0 0 eth0 default 192.168.21.1 0.0.0.0 UG 100 0 0 eth1 Route table on OSX: $ netstat -nr Routing tables Internet: Destination Gateway Flags Refs Use Netif Expire default 10.77.36.1 UGSc 28 0 en1 10.77.36/22 link#5 UCS 5 0 en1 10.77.39.38 127.0.0.1 UHS 1 2236 lo0 10.77.39.255 link#5 UHLWbI 1 66 en1 127 127.0.0.1 UCS 0 0 lo0 127.0.0.1 127.0.0.1 UH 1 8642 lo0 169.254 link#5 UCS 0 0 en1 192.168.21 link#7 UC 2 0 vboxnet 192.168.21.20 a:0:27:0:0:0 UHLWI 0 4 lo0 192.168.21.255 link#7 UHLWbI 2 64 vboxnet I can't SSH from the host to the guest (I used to be able to when the VM was configured with a bridged connection): $ ssh 192.168.21.20 ssh: connect to host 192.168.21.20 port 22: Connection refused What have I done wrong here? TIA

  Read the article

• Fetching e-mails into Redmine via IMAP

  - by Danilo Bargen

  I'm trying to fetch e-mails into Redmine via IMAP. The e-mails I'm generating look like this: FooBar Ltd 123456 http://example.com/Foobar-Ltd-123456.html Project: backend Tracker: Dataerror Beschreibung: This is the description =========================== CLIENT_IP: 192.168.1.215 HTTP_USER_AGENT: mozilla/asdfjköl I try to fetch them into Redmine via this command: rake -f /var/www/projects/redmine/Rakefile redmine:email:receive_imap \ RAILS_ENV="production" host=example.com port=993 ssl=true username=redmine \ password=1234 project=myproject tracker=other \ allow_override=project,tracker,category,priority \ move_on_success=read move_on_failure=failed But the e-mails get moved into the failed folder. I had this setup running some time ago with a different e-mail generator but pretty much the same template, and I can't figure out why it's not working. The permissions seem to be OK too. In order to further debug this issue, I need some logfiles. Are there any logfiles written by this command? Or are there any other suggestions to solve this issue? My environment: danilo@jabba:/var/www/projects/redmine$ RAILS_ENV=production script/about About your application's environment Ruby version 1.8.7 (i486-linux) RubyGems version 1.3.5 Rack version 1.0 Rails version 2.3.5 Active Record version 2.3.5 Active Resource version 2.3.5 Action Mailer version 2.3.5 Active Support version 2.3.5 Application root /var/www/projects/redmine Environment production Database adapter mysql Database schema version 20100819172912

  Read the article

• Query specific logs from event log using nxlog

  - by user170899

  Below is my nxlog configuration define ROOT C:\Program Files (x86)\nxlog Moduledir %ROOT%\modules CacheDir %ROOT%\data Pidfile %ROOT%\data\nxlog.pid SpoolDir %ROOT%\data LogFile %ROOT%\data\nxlog.log <Extension json> Module xm_json </Extension> <Input internal> Module im_internal </Input> <Input eventlog> Module im_msvistalog Query <QueryList>\ <Query Id="0">\ <Select Path="Security">*</Select>\ </Query>\ </QueryList> </Input> <Output out> Module om_tcp Host localhost Port 3515 Exec $EventReceivedTime = integer($EventReceivedTime) / 1000000; \ to_json(); </Output> <Route 1> Path eventlog, internal => out </Route> <Select Path="Security">*</Select>\ - * gets everything from the Security log, but my requirement is to get specific logs starting with EventId - 4663. How do i do this? Please help. Thanks.

  Read the article

< Previous Page | 361 362 363 364 365 366 367 368 369 370 371 372  | Next Page >