Search Results

Search found 40031 results on 1602 pages for 'command message'.

Page 367/1602 | < Previous Page | 363 364 365 366 367 368 369 370 371 372 373 374  | Next Page >

• Un-failing over a Cisco PIX 515e

  - by ABrown

  We had a power outage at our data center last week and when our dual PIX 515E running IOS 7.0(8) (configured with a failover cable) came back, they were in a failed over state where the Secondary unit is active and the Primary unit is standby I have tried 'failover reset', 'failover active', and 'failover reload-standby' as well as executing reloads on both units in a variety of orders, and they don't come back Primary/Active Secondary/Standby. The only thing in my arsenal that I haven't tried is driving to the data center and performing a hard reboot, which I hate to do. I have read How Failover Works on the Cisco Secure Firewall and it seems like this should be wicked straight forward. output of show failover on Primary: Failover On Cable status: Normal Failover unit Primary Failover LAN Interface: N/A - Serial-based failover enabled Unit Poll frequency 15 seconds, holdtime 45 seconds Interface Poll frequency 15 seconds Interface Policy 1 Monitored Interfaces 2 of 250 maximum Version: Ours 7.0(8), Mate 7.0(8) Last Failover at: 02:52:05 UTC Mar 10 2010 This host: Primary - Standby Ready Active time: 0 (sec) Interface outside (x.x.x.165): Normal Interface inside (y.y.y.3): Normal Other host: Secondary - Active Active time: 897045 (sec) Interface outside (x.x.x.164): Normal Interface inside (y.y.y.4): Normal Stateful Failover Logical Update Statistics Link : Unconfigured. output of show failover on Secondary: Failover On Cable status: Normal Failover unit Secondary Failover LAN Interface: N/A - Serial-based failover enabled Unit Poll frequency 15 seconds, holdtime 45 seconds Interface Poll frequency 15 seconds Interface Policy 1 Monitored Interfaces 2 of 250 maximum Version: Ours 7.0(8), Mate 7.0(8) Last Failover at: 02:03:04 UTC Feb 28 2010 This host: Secondary - Active Active time: 896925 (sec) Interface outside (x.x.x.164): Normal Interface inside (y.y.y.4): Normal Other host: Primary - Standby Ready Active time: 0 (sec) Interface outside (x.x.x.165): Normal Interface inside (y.y.y.3): Normal Stateful Failover Logical Update Statistics Link : Unconfigured. I'm seeing the following in my syslog: Mar 10 03:05:00 fw1 %PIX-5-111008: User 'enable_15' executed the 'failover reset' command. Mar 10 03:05:09 fw1 %PIX-5-111008: User 'enable_15' executed the 'failover reload-standby' command. Mar 10 03:05:12 fw1 %PIX-6-720032: (VPN-Secondary) HA status callback: id=3,seq=200,grp=0,event=406,op=20,my=Active,peer=Failed. Mar 10 03:05:12 fw1 %PIX-6-720028: (VPN-Secondary) HA status callback: Peer state Failed. Mar 10 03:06:09 fw1 %PIX-6-720032: (VPN-Secondary) HA status callback: id=3,seq=200,grp=0,event=401,op=0,my=Active,peer=Failed. Mar 10 03:06:09 fw1 %PIX-6-720024: (VPN-Secondary) HA status callback: Control channel is down. Mar 10 03:06:09 fw1 %PIX-6-720032: (VPN-Secondary) HA status callback: id=3,seq=200,grp=0,event=401,op=1,my=Active,peer=Failed. Mar 10 03:06:10 fw1 %PIX-6-720024: (VPN-Secondary) HA status callback: Control channel is up. Mar 10 03:06:10 fw1 %PIX-6-720032: (VPN-Secondary) HA status callback: id=3,seq=200,grp=0,event=411,op=2,my=Active,peer=Failed. Mar 10 03:06:23 fw1 %PIX-6-720032: (VPN-Secondary) HA status callback: id=3,seq=200,grp=0,event=406,op=80,my=Active,peer=Standby Ready. Mar 10 03:06:23 fw1 %PIX-6-720028: (VPN-Secondary) HA status callback: Peer state Standby Ready. Mar 10 03:06:24 fw2 %PIX-6-720027: (VPN-Primary) HA status callback: My state Standby Ready. Mar 10 03:07:05 fw1 %PIX-5-111008: User 'enable_15' executed the 'failover reset' command. Mar 10 03:07:31 fw1 %PIX-5-111008: User 'enable_15' executed the 'failover active' command. Mar 10 03:08:04 fw1 %PIX-5-611103: User logged out: Uname: enable_1 Mar 10 03:08:04 fw1 %PIX-6-315011: SSH session from admin1_int on interface inside for user "pix" terminated normally Mar 10 03:08:39 fw1 %PIX-6-720032: (VPN-Secondary) HA status callback: id=3,seq=200,grp=0,event=406,op=20,my=Active,peer=Failed. Mar 10 03:08:39 fw1 %PIX-6-720028: (VPN-Secondary) HA status callback: Peer state Failed. Mar 10 03:09:10 fw1 %PIX-6-605005: Login permitted from admin1_int/36891 to inside:192.168.4.4/ssh for user "pix" Mar 10 03:09:23 fw1 %PIX-5-111008: User 'enable_15' executed the 'failover reset' command. Mar 10 03:09:38 fw1 %PIX-6-720032: (VPN-Secondary) HA status callback: id=3,seq=200,grp=0,event=401,op=0,my=Active,peer=Failed. Mar 10 03:09:39 fw1 %PIX-6-720024: (VPN-Secondary) HA status callback: Control channel is down. Mar 10 03:09:39 fw1 %PIX-6-720032: (VPN-Secondary) HA status callback: id=3,seq=200,grp=0,event=401,op=1,my=Active,peer=Failed. Mar 10 03:09:39 fw1 %PIX-6-720024: (VPN-Secondary) HA status callback: Control channel is up. Mar 10 03:09:39 fw1 %PIX-6-720032: (VPN-Secondary) HA status callback: id=3,seq=200,grp=0,event=411,op=2,my=Active,peer=Failed. Mar 10 03:09:52 fw1 %PIX-6-720032: (VPN-Secondary) HA status callback: id=3,seq=200,grp=0,event=406,op=80,my=Active,peer=Standby Ready. Mar 10 03:09:52 fw1 %PIX-6-720028: (VPN-Secondary) HA status callback: Peer state Standby Ready. Mar 10 03:09:53 fw2 %PIX-6-720027: (VPN-Primary) HA status callback: My state Standby Ready. I'm not exactly sure how to interpret that syslog data. Primary doesn't seem to even try to become Active. When I reload the individual units separately, my connections are retained, so it doesn't seem like I have a real hardware failure. Is there something I can query (IOS or SNMP) to check for hardware issues? Any thoughts? My IOS-fu is weak. Thanks for any help you might provide, Aaron

  Read the article

• Chester Devs Presentation and source code &ndash; &lsquo;Event Store - an introduction to a DSD for event sourcing and notifications&rsquo;

  - by Liam Westley

  Originally posted on: http://geekswithblogs.net/twickers/archive/2013/11/11/chester-devs-presentation-and-source-code-ndash-lsquoevent-store.aspxThank you everyone at Chester Devs Thanks to Fran Hoey and all the people from Chester Devs. It was a hard drive up and back but the enthusiasm of the audience, with some great questions does make it worthwhile. Presentation and source code My presentation, source code, Event Store runners and text files containing the various command line parameters used for curl is now available on GitHub; https://github.com/westleyl/ChesterDevs-EventStore. Don’t worry if you don’t have a GitHub account, you don’t need one, you can just click on the Download Zip button on the right hand menu to download all the files as a single ZIP file.  If all you want is the PowerPoint presentation, go to https://github.com/westleyl/ChesterDevs-EventStore/blob/master/Powerpoint/Huddle-EventStore.pptx, and click on the View Raw button. Downloading and installing Event Store and Tools Download Event Store http://download.geteventstore.com – I unzipped these files into C:\EventStore\v2.0.1 Download Curl from http://curl.haxx.se/download.html – I downloaded Win64 Generic (with SSL) and unzipped these files into C:\curl version 7.31.0 Running the tools I used in my presentation Demonstration 1 (running Event Store) You can use one of my Event Store runner command files to run the single node version of Event Store, using default ports of 2213 for HTTP and 1113  for TCP, and with a wildcard HTTP pattern.  Both take a single command line parameter to specify the location of the data and log files.  The runners assume the single node executable is located in C:\EventStore\v2.0.1, and will placed data files and logs beneath C:\EventStore\Data, i.e. RunEventStore.cmd TestData1 This will create data files in C:\EventStore\Data\TestData1\Data and log files in C:\EventStore\Data\TestData1\logs. If, when running Event Store you may see the following message, [03288,15,06:23:00.622] Failed to start http server Access is denied You will either need to run Event Store in an administrator console window, or you can use the netsh command to create a firewall permission to allow HTTP listening (this will need to be run, once, in an administrator console window), netsh http add urlacl url=http://*:2213/ user=liam You can always delete this later by running the delete; netsh http delete urlacl url=http://*:2213/ If you want to confirm that everything is running OK, open the management console in a browser by navigating to http://127.0.0.1:2213. If at any point you are asked for a user name and password use the default of ‘admin’/‘changeit’. Demonstration 2 (reading and adding data, curl) In my second demonstration I used curl directly from the console to read streams, write events and then read back those events. On GitHub I have included is a set of curl commands, CurlCommandLine.txt, and a sample data file, SampleData.json, to load an event into a DDDNorth3 stream. As there is not much data in the Event Store at this point I used the $stats-127.0.0.1:2113 which is a stream containing performance statistics for Event Store and is updated every 30 seconds (default). Demonstration 3 (projections) On GitHub I have included a sample projection, Projection-ByRoom.txt, which will create streams based on the room on which a session was held on the DDDNorth3 agenda. Browse to the management console, http://127.0.0.1:2213.  Click on Projections, New Projection, give it a name, Sessions-ByRoom, and copy in the JavaScript in the Projection-ByRoom.txt file.  Select Continuous, tick Emit Enabled and then click on Post. It should run immediately. You may by challenged for the administration login for the management console, if so use the default user name and password; 'admin'/'changeit'. Demonstration 4 (C# client) The final demonstration was the Visual Studio 2012 project using the Event Store client – referenced directly as C:\EventStore\v2.0.1\EventStore.ClientAPI.dll, although you can switch this to the latest Event Store client NuGet package. The source code provides a console app for viewing projections with the projection manager (HTTP connection), as well as containing a full set of data for the entire DDDNorth3 agenda.  It also deals with the strategy for reading newest events backwards to older events and ignoring older events that have been superseded. Resources Event Store home page: http://www.geteventstore.com/ Event Store source code on GitHub: https://github.com/eventstore/eventstore Event Store documentation on GitHub: https://github.com/eventstore/eventstore/wiki (includes index to @RobAshton’s blog series on Event Store at https://github.com/eventstore/eventstore/wiki#rob-ashton---projections-series) Event Store forum in Google Groups: https://groups.google.com/forum/?fromgroups#!forum/event-store TopShelf Windows service wrapper is available on github: https://gist.github.com/trbngr/5083266

  Read the article

• How to fix: Handler “PageHandlerFactory-Integrated” has a bad module “ManagedPipelineHandler” in its module list

  - by ybbest

  Issue: Recently, I am having issues with deploying asp.net mvc 4 application to Windows Server 2008 R2.After add the necessary role and features and I setup an application in IIS. However , I received the following error message: PageHandlerFactory-Integrated” has a bad module “ManagedPipelineHandler” in its module list   Solution: It turns out that this is because ASP.Net was not completely installed with IIS even though I checked that box in the “Add Feature” dialog.   To fix this, I simply ran the following command at the command prompt %windir%\Microsoft.NET\Framework64\v4.0.30319\aspnet_regiis.exe -i If I had been on a 32 bit system, it would have looked like the following: %windir%\Microsoft.NET\Framework\v4.0.21006\aspnet_regiis.exe –i   References: http://stackoverflow.com/questions/6846544/how-to-fix-handler-pagehandlerfactory-integrated-has-a-bad-module-managedpip

  Read the article

• Google-bot sees “Sorry, we have no imagery here” on pages with Google Maps

  - by friism

  I have a site with Google Maps on most of the pages. When inspecting content keywords in Google Webmaster tools, content keywords identified by Google-bot for the site include "imagery", "sorry" and "here". These turn out to be part of an error message returned by Google Maps: "Sorry, we have no imagery here". I cannot reproduce this error with normal clients, nor does "fetch as Google" show it. The problem is presumably that Google-bot tries to execute some of the Google Maps Javascript but then shoots itself on the foot and records the error message. A Google search for "Sorry, we have no imagery here" shows that this problem is endemic to sites across the internet, including Yelp and many others. I'd like to convince Google that my site is not about imagery and being sorry, but I'd also like to keep the maps in place. I guess one option would be to transition to static maps, but that's not a great alternative. There's some related discussion on Webmaster World, no resolution.

  Read the article

• DDD North 3 Presentation and source code &ndash; &lsquo;Event Store - an introduction to a DSD for event sourcing and notifications&rsquo;

  - by Liam Westley

  Originally posted on: http://geekswithblogs.net/twickers/archive/2013/10/15/ddd-north-3-presentation-and-source-code-ndash-lsquoevent-store.aspxThank you everyone at DDD North Thanks to all the people who helped organise the cracking conference that is DDD North 3, returning to Sunderland, and the great facilities at the University of Sunderland, and the fine drinks reception at Sunderland Software City.  The whole event wouldn’t be possible without the sponsors who ensured over 400 people were kept fed and watered so they could enjoy the impressive range of sessions. And lastly, a thank you to all those delegates who gave up their free time on a Saturday to spend a day dashing between lecture rooms, including a late change to my room which saw 40 people having to brave a journey between buildings in the fine drizzle. The enthusiasm from the delegates always helps recharge my geek batteries. Presentation and source code My presentation, source code, Event Store runners and text files containing the various command line parameters used for curl is now available on GitHub; https://github.com/westleyl/DDDNorth3-EventStore. Don’t worry if you don’t have a GitHub account, you don’t need one, you can just click on the Download Zip button on the right hand menu to download all the files as a single ZIP file.  If all you want is the PowerPoint presentation, go to https://github.com/westleyl/DDDNorth3-EventStore/blob/master/Powerpoint/DDDNorth-EventStore.pptx, and click on the View Raw button. Downloading and installing Event Store and Tools Download Event Store http://download.geteventstore.com – I unzipped these files into C:\EventStore\v2.0.1 Download Curl from http://curl.haxx.se/download.html – I downloaded Win64 Generic (with SSL) and unzipped these files into C:\curl version 7.31.0 Running the tools I used in my presentation Demonstration 1 (running Event Store) You can use one of my Event Store runner command files to run the single node version of Event Store, using default ports of 2213 for HTTP and 1113  for TCP, and with a wildcard HTTP pattern.  Both take a single command line parameter to specify the location of the data and log files.  The runners assume the single node executable is located in C:\EventStore\v2.0.1, and will placed data files and logs beneath C:\EventStore\Data, i.e. RunEventStore.cmd TestData1 This will create data files in C:\EventStore\Data\TestData1\Data and log files in C:\EventStore\Data\TestData1\logs. If, when running Event Store you may see the following message, [03288,15,06:23:00.622] Failed to start http server Access is denied You will either need to run Event Store in an administrator console window, or you can use the netsh command to create a firewall permission to allow HTTP listening (this will need to be run, once, in an administrator console window), netsh http add urlacl url=http://*:2213/ user=liam You can always delete this later by running the delete; netsh http delete urlacl url=http://*:2213/ If you want to confirm that everything is running OK, open the management console in a browser by navigating to http://127.0.0.1:2213. If at any point you are asked for a user name and password use the default of ‘admin’/‘changeit’.   Demonstration 2 (reading and adding data, curl) In my second demonstration I used curl directly from the console to read streams, write events and then read back those events. On GitHub I have included is a set of curl commands, CurlCommandLine.txt, and a sample data file, SampleData.json, to load an event into a DDDNorth3 stream. As there is not much data in the Event Store at this point I used the $stats-127.0.0.1:2113 which is a stream containing performance statistics for Event Store and is updated every 30 seconds (default). Demonstration 3 (projections) On GitHub I have included a sample projection, Projection-ByRoom.txt, which will create streams based on the room on which a session was held on the DDDNorth3 agenda. Browse to the management console, http://127.0.0.1:2213.  Click on Projections, New Projection, give it a name, Sessions-ByRoom, and copy in the JavaScript in the Projection-ByRoom.txt file.  Select Continuous, tick Emit Enabled and then click on Post. It should run immediately. You may by challenged for the administration login for the management console, if so use the default user name and password; 'admin'/'changeit'.   Demonstration 4 (C# client) The final demonstration was the Visual Studio 2012 project using the Event Store client – referenced directly as C:\EventStore\v2.0.1\EventStore.ClientAPI.dll, although you can switch this to the latest Event Store client NuGet package. The source code provides a console app for viewing projections with the projection manager (HTTP connection), as well as containing a full set of data for the entire DDDNorth3 agenda.  It also deals with the strategy for reading newest events backwards to older events and ignoring older events that have been superseded. Resources Event Store home page: http://www.geteventstore.com/ Event Store source code on GitHub: https://github.com/eventstore/eventstore Event Store documentation on GitHub: https://github.com/eventstore/eventstore/wiki (includes index to @RobAshton’s blog series on Event Store at https://github.com/eventstore/eventstore/wiki#rob-ashton---projections-series) Event Store forum in Google Groups: https://groups.google.com/forum/?fromgroups#!forum/event-store TopShelf Windows service wrapper is available on github: https://gist.github.com/trbngr/5083266

  Read the article

• How to fix “Microsoft SharePoint is not supported with version 4.0.30319.225 of the Microsoft .Net Runtime” in PowerGUI

  - by ybbest

  Today, when I try to run some PowerShell command against SharePoint in PowerGUI , I encounter some error message as below: Problem: Remove-SPSite : Microsoft SharePoint is not supported with version 4.0.30319.225 of the Microsoft .Net Runtime. At C:\SiteCreation.ps1:37 char:14 + CategoryInfo : InvalidData: (Microsoft.Share…mdletRemoveSite:SPCmdletRemoveSite) [Remove-SPSite], PlatformNotSupportedException Analysis: The error message is pretty clear that PowerGUI try to run the PowerShell command under .Net version 4.0 which is not supported by SharePoint2010, SharePoint2010 only support .Net 3.5.So how can I change the settings so that PowerShell does run under .Net3.5 in PowerGui? The solution is pretty easy. Solution: 1. Open your windows explorer and navigate to C:\Program Files (x86)\PowerGUI\ and open the configuration file ScriptEditor.exe.config. 2. Change the supportedRuntime version under Startup settings by removing the version=”v4.0″ as below From To   3. Restart your PowerGUI and rerun your script. It works like a charm.

  Read the article

• It’s time that you ought to know what you don’t know

  - by fatherjack

  There is a famous quote about unknown unknowns and known knowns and so on but I’ll let you review that if you are interested. What I am worried about is that there are things going on in your environment that you ought to know about, indeed you have asked to be told about but you are not getting the information. When you schedule a SQL Agent job you can set it to send an email to an inbox monitored by someone who needs to know and indeed can do something about it. However, what happens if the email process isnt successful? Check your servers with this: USE [msdb] GO /* This code selects the top 10 most recent SQLAgent jobs that failed to complete successfully and where the email notification failed too. Jonathan Allen Jul 2012 */ DECLARE @Date DATETIME SELECT @Date = DATEADD(d, DATEDIFF(d, '19000101', GETDATE()) - 1, '19000101') SELECT TOP 10 [s].[name] , [sjh].[step_name] , [sjh].[sql_message_id] , [sjh].[sql_severity] , [sjh].[message] , [sjh].[run_date] , [sjh].[run_time] , [sjh].[run_duration] , [sjh].[operator_id_emailed] , [sjh].[operator_id_netsent] , [sjh].[operator_id_paged] , [sjh].[retries_attempted] FROM [dbo].[sysjobhistory] AS sjh INNER JOIN [dbo].[sysjobs] AS s ON [sjh].[job_id] = [s].[job_id] WHERE EXISTS ( SELECT * FROM [dbo].[sysjobs] AS s INNER JOIN [dbo].[sysjobhistory] AS s2 ON [s].[job_id] = [s2].[job_id] WHERE [sjh].[job_id] = [s2].[job_id] AND [s2].[message] LIKE '%failed to notify%' AND CONVERT(DATETIME, CONVERT(VARCHAR(15), [s2].[run_date])) >= @date AND [s2].[run_status] = 0 ) AND sjh.[run_status] = 0 AND sjh.[step_id] != 0 AND CONVERT(DATETIME, CONVERT(VARCHAR(15), [run_date])) >= @date ORDER BY [sjh].[run_date] DESC , [sjh].[run_time] DESC go USE [msdb] go /* This code summarises details of SQLAgent jobs that failed to complete successfully and where the email notification failed too. Jonathan Allen Jul 2012 */ DECLARE @Date DATETIME SELECT @Date = DATEADD(d, DATEDIFF(d, '19000101', GETDATE()) - 1, '19000101') SELECT [s].name , [s2].[step_id] , CONVERT(DATETIME, CONVERT(VARCHAR(15), [s2].[run_date])) AS [rundate] , COUNT(*) AS [execution count] FROM [dbo].[sysjobs] AS s INNER JOIN [dbo].[sysjobhistory] AS s2 ON [s].[job_id] = [s2].[job_id] WHERE [s2].[message] LIKE '%failed to notify%' AND CONVERT(DATETIME, CONVERT(VARCHAR(15), [s2].[run_date])) >= @date AND [s2].[run_status] = 0 GROUP BY name , [s2].[step_id] , [s2].[run_date] ORDER BY [s2].[run_dateDESC] These two result sets will show if there are any SQL Agent jobs that have run on your servers that failed and failed to successfully email about the failure. I hope it’s of use to you. Disclaimer – Jonathan is a Friend of Red Gate and as such, whenever they are discussed, will have a generally positive disposition towards Red Gate tools. Other tools are often available and you should always try others before you come back and buy the Red Gate ones. All code in this blog is provided “as is” and no guarantee, warranty or accuracy is applicable or inferred, run the code on a test server and be sure to understand it before you run it on a server that means a lot to you or your manager.

  Read the article

• Enhance Internet Explorer 9 with Add-Ons

  - by Lori Kaufman

  If you’re one of those who still use that “other” browser (Internet Explorer or IE), you’ll be glad to know that there are ways to extend the functionality of IE just like you can in Firefox or Chrome. There are not as many add-ons for Internet Explorer as there are for Firefox and Chrome, but you can explore the official Internet Explorer Gallery to see if there are any that peek your interest. In this article, we show you how to install add-ons in Internet Explorer 9. To begin, activate the Command bar, if it’s not already available. Right-click on an empty area of the tab bar and select Command bar from the popup menu. HTG Explains: Why Linux Doesn’t Need Defragmenting How to Convert News Feeds to Ebooks with Calibre How To Customize Your Wallpaper with Google Image Searches, RSS Feeds, and More

  Read the article

• CodePlex Daily Summary for Friday, May 14, 2010

  CodePlex Daily Summary for Friday, May 14, 2010New ProjectsCampfire#: Campfire# is a campfire client written in .NET 4.0 using WPF, which uses the Campfire API.CHESS: Systematic Concurrency Testing: CHESS is a tool for systematic and disciplined concurrency testing. Given a concurrent test, CHESS systematically enumerates the possible thread sc...cmpp: cmppcycloid: Arcanoid gameDotNetNuke® C#: The DotNetNuke® project is developed and maintained on a Visual Basic codebase, however a C# version has always been a popular request. This is a ...EasyBuildingCMS.NET: EasyBuildingCMS is an easy use content management system.fluidCMS: Provide for flexible management of web content that is not tightly integrated with the layout and rendering of sites that consume the content.Golem: An automation tool oriented to localization engineering environmentHB Batch Encoder Mk 2: HandBrake Batch Encoder Mk II This Program was adapted from an original project downloaded from codeplex by the name of "Handbrake Batch Encoder"...Integrating Social Media Networks: This is part of my pos graduation project.Ketonic: The Ketonic project aims to improve development of websites based on the Kentico CMS. LinkSharp: LinkSharp is a short-URL provider that can be used to generate short static non changing URL's. The web interface allows you to easily add / edit /...PUC NET (C++ Network Library - PUC Minas): This is an Academic Library for an Easy Development of Applications and Games based on Network Communication.Regular Expression Tester: Small utility for testing regular expressionsSharePoint User Management WebPart: SharePoint User Management WebPartSharpBox: SharpBox makes it easier for .NET developers to interact with existing cloud storage service, e.g. DropBox or Amazon S3Snipivit: Snipivit is a snippet manager service and VS2010 plugin that allows small development teams to store all their code snippets on a central database,...Software Factories Applied: Software Factories Applied is a project collecting the companion bits for the eponymous book to be published by Wiley & Sons in 2011. The authors ...The Ping Master: A service that periodically pings network addresses and allows the running of command line type utilities in response to success or failure.Title Safe Region Checker: A simple utility for XNA developers to check screenshots from games intended for release on the LIVE Marketplace for "title safe" region compliance...Trial project: sky is blueUyghur Named Date: Generate Uyghur named date string. ئۇيغۇرچە ئاي ناملىق چىسلا ھاسىل قىلىشWildcard Search Web Part for SharePoint 2010: The Wildcard Search web part for MOSS 2007 was wildly successful. Although, SharePoint 2010 has built-in wildcard searching functionality, the out...在线Office控件 Online Offical Control: 在线Office控件软件作品发布平台: SoftwarePublishPlatform 软件作品发布平台New ReleasesDemina: Demina Binaries version 0.1: Demina binaries are now available. This release (version 0.1) is an alpha version. Please report any bugs for extermination.EasyTFS: EasyTfs 1.0 Beta 2: Added cache refreshing when contents are updated rather than just every 10 minutes. Added window title based on currently-open case. Added attachme...Extending C# editor - Outlining, classification: Initial release: Initial releaseHB Batch Encoder Mk 2: HB Batch Encoder Mk2 v1.01: Binary release files.HB Batch Encoder Mk 2: Source Code: Source CodeHobbyBrew Mobile: Beta 2: Corretti numerosi bug, data un implementazione "approssimativa" del riscaldamento per Infusione. Aggiornamento consigliato!HouseFly controls: HouseFly controls beta 1.0.2.0: HouseFly controls relase 1.0.2.0 betaHtml Reader: Beta 2: I fixed a bug in HtmlElementCollection, Which exposed an integer enumerator, instead of enumerating through HtmlElements. I added a WPF Window tha...Html to OpenXml: HtmlToOpenXml 1.2: Fix some reported bug. See change set for description. The dll library to include in your project. The dll is signed for GAC support. Compiled wi...Infection Protection: Infection Protection 0.1: This is the final version of Infection Protection that was entered into the 2010 OGPC game competition.Jobping Url Shortener: Deploy Code 0.5.1: Deployment code for Version 0.5 This version includes our Jobping style.Jobping Url Shortener: Source Code 0.5.1: Source code for the 0.5 release. This release includes our Jobping style skin.Kooboo HTML form: Kooboo HTML form module 2.1.0.1: HTML form module contributed by member aledelgo. Add SMTP user and password authentication.KooBoo Image Galery: Beta 2: This new version corrects some issues pointed by Guoqi Zheng Some schema and folders were renamed, so it's better to uninstall the module and remo...MFCMAPI: May 2010 Release: If you just want to run the tool, get the executable. If you want to debug it, get the symbol file and the source. Build: 6.0.0.1020 The 64 bit bu...MVC Turbine: Release 2.1 for MVC2: This RTM contains the same features as v2.0 RTM plus these features: Instance Registration to IServiceLocator You can now add an instance of a typ...NazTek.Extension.Clr4: NazTek.Extension.Clr4 Binary: Binary releaseNazTek.Extension.Clr4: NazTek.Extension.Clr4 Source: Cab with source codeNSIS Autorun: NSIS Autorun 0.1.8: This release includes source code, executable binaries and example materials.Ottawa IT Day: 2010 Source Code and Presentations: During the Ottawa IT Day 2010, some of the presenters shared their code (and some presentations). This release is the culmination of all those effo...PHPWord: PHPWord 0.6.1 Beta: Changelog: Fixed Error when adding a JPEG image and opening in office 2007 Issue #1 Fixed Already defined constant PHPWORD_BASE_PATH Issue #2 F...Rapid Dictionary: Rapid Dictionary Alpha 2.0: Release Notes * Try auto updatable version: http://install.rapiddict.com/index.html Rapid Dictionary Alpha 2.0 includes such functionality: ...Shake - C# Make: Shake v0.1.18: Core changes. Process wrapper class, console logger, etc.SharpBox: SharpBox-Trunk: This is the SharpBox build from the trunk source branch!SharpBox: SharpBox-Trunk-Initial-Source: The initial source code, will be updated from time to timeSpackle.NET: 4.0.0.0 Release: This new drop contains the following A CreateBigInteger() method on SecureRandom to create random BigInteger values. An extension method to prop...StreamInsight example queries, input adapters and output adapters: StreamInsight Examples for V1.0 RTM: Zipped source code.The Ping Master: v0.1.0.0: Early release of The Ping Master for test purposes. Configuration tool is unfinished and does not include an installer.Title Safe Region Checker: Title Safe Region Checker v1.0.0.1: Release 1.0 of Title Safe Region Checker. No known bugs or problems. File is a zipped directory containing the necessary installation files.TortoiseHg: TortoiseHg 1.0.3: This is a bug fix release, we recommend all users upgrade to 1.0.3Usa*Usa Libraly: Smart.Windows.Navigation 0.4: Smart.Windows.Navigation simple navigation library ver 0.4.0. Include Windows Forms & Compact Framework samples. Information - Smart.Windows.Mvc ...VCC: Latest build, v2.1.30513.0: Automatic drop of latest buildWabbitStudio Z80 Software Tools: Wabbitcode: Wabbitcode is an Z80 Assembly IDE for Windows, OS X, and Linux. Built to take full advantage of the features of SPASM and Wabbitemu, Wabbitcode has...white: Release 0.20: Source Code: https://white-project.googlecode.com/svn/tags/0.20 Add few more keyboard keys like windows button and F13-F24. Fixed bugs for keyboar...Wildcard Search Web Part for SharePoint 2010: Version 1.0 Release 1: This is the initial release of the Wildcard Search Web Part for SharePoint 2010. All queries will be issued as wildcards unless disabled with the ...Windows Azure Command-line Tools for PHP Developers: Windows Azure Command-line Tools May 2010 Update: May 2010 Update – May 13, 2010 We are pleased to announced the May 2010 update of Windows Azure Command-Line Tools. In addition to bug fixes and i...WinXmlCook: WinXmlCook 2.1: Version 2.1 released!Xrns2XMod: Xrns2XMod 1.1: some source code optimization在线Office控件 Online Offical Control: SPOffice2.0Release: 该版本在MS Office2003/2007，WPS2009，WPS2010下测试通过Most Popular ProjectsRawrWBFS ManagerAJAX Control ToolkitMicrosoft SQL Server Product Samples: DatabaseSilverlight ToolkitWindows Presentation Foundation (WPF)patterns & practices – Enterprise LibraryMicrosoft SQL Server Community & SamplesPHPExcelASP.NETMost Active Projectspatterns & practices – Enterprise LibraryMirror Testing SystemRawrBlogEngine.NETPHPExcelMicrosoft Biology FoundationwhiteWindows Azure Command-line Tools for PHP DevelopersStyleCopShake - C# Make

  Read the article

• How To Disconnect Non-Mapped UNC Path “Drives” in Windows

  - by The Geek

  Have you ever browsed over to another PC on your network using “network neighborhood”, and then connected to one of the file shares? Without a drive letter, how do you disconnect yourself once you’ve done so? Really confused as to what I’m talking about? Let’s walk through the process. First, imagine that you browse through and connect to a share, entering your username and password to gain access. The problem is that you stay connected, and there’s no visible way to disconnect yourself. If you try and shut down the other PC, you’ll receive a message that users are still connected. So let’s disconnect! Open up a command prompt, and then type in the following: net use This will give you a list of the connected drives, including the ones that aren’t actually mapped to a drive letter. To disconnect one of the connections, you can use the following command: net use /delete \\server\sharename For example, in this instance we’d disconnect like so: net use /delete \\192.168.1.205\root$ Now when you run the “net use” command again, you’ll see that you’ve been properly disconnected. If you wanted to actually connect to a share without mapping a drive letter, you can do the following: net use /user:Username \\server\sharename Password You could then just pop \\server\sharename into a Windows Explorer window and browse the files that way. Note that this technique should work exactly the same in any version of windows. Similar Articles Productive Geek Tips Remove "Map Network Drive" Menu Item from Windows Vista or XPDisable the Annoying "This page has an unspecified potential security risk" When Using Files on a Network ShareCopy Path of a File to the Clipboard in Windows 7 or VistaMap a Network Drive from XP to Windows 7Defrag Multiple Hard Drives At Once In Windows TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips DVDFab 6 Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 Enable DreamScene in Windows 7 Microsoft’s “How Do I ?” Videos Home Networks – How do they look like & the problems they cause Check Your IMAP Mail Offline In Thunderbird Follow Finder Finds You Twitter Users To Follow Combine MP3 Files Easily

  Read the article

• Need help with PHP web app bootstrapping error potentially related to Zend [migrated]

  - by Matt Shepherd

  I am trying to get a program called OpenFISMA running on an Ubuntu AMI in AWS. The app is not really coded on the Ubuntu platform, but I am in my comfort zone there, and have tried both CentOS and OpenSUSE (both are sort of "native" for the app) for getting it working with the same or worse results. So, why not just get it working on Ubuntu? Anyway, the app is found here: www.openfisma.org and an install guide is found here: https://openfisma.atlassian.net/wiki/display/030100/Installation+Guide The install guide kind of sucks. It doesn't list dependencies in any coherent way or provide much of any detail (does not even mention Zend once on the entire page) so I've done a lot of work to divine the information I do have. This page provided some dependency inf (though again, Zend is not mentioned once): https://openfisma.atlassian.net/wiki/display/PUBLIC/RPM+Management#RPMManagement-BasicOverviewofRPMPackages Anyway, I got all the way through the install (so far as I could reconstruct it). I am going to the login page for the first time, and there should be some sort of bootstrapping occurring when I load the page. (I am not a programmer so I have no idea what it is doing there.) Anyway, I get a message on the web page that says: "An exception occurred while bootstrapping the application." So, then I go look in /var/www/data/logs/php.log and find this message: [22-Oct-2013 17:29:18 UTC] PHP Fatal error: Uncaught exception 'Zend_Exception' with message 'No entry is registered for key 'Zend_Log'' in /var/www/library/Zend/Registry.php:147 Stack trace: #0 /var/www/public/index.php(188): Zend_Registry::get('Zend_Log') #1 {main} thrown in /var/www/library/Zend/Registry.php on line 147 This occurs every time I load the page. I gather there is an issue related to registering the Zend_Log variable in the Zend registry, but other than that I really have no idea what to do about it. Am I missing a package that it needs, or is this app not coded to register the variables properly? I have no clue. Any help is greatly appreciated. The application file referenced in the log message (index.php) is included below. <?php /** * Copyright (c) 2008 Endeavor Systems, Inc. * * This file is part of OpenFISMA. * * OpenFISMA is free software: you can redistribute it and/or modify it under the terms of the GNU General Public * License as published by the Free Software Foundation, either version 3 of the License, or (at your option) any later * version. * * OpenFISMA is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied * warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more * details. * * You should have received a copy of the GNU General Public License along with OpenFISMA. If not, see * {@link http://www.gnu.org/licenses/}. */ try { defined('APPLICATION_PATH') || define( 'APPLICATION_PATH', realpath(dirname(__FILE__) . '/../application') ); // Define application environment defined('APPLICATION_ENV') || define( 'APPLICATION_ENV', (getenv('APPLICATION_ENV') ? getenv('APPLICATION_ENV') : 'production') ); set_include_path( APPLICATION_PATH . '/../library/Symfony/Components' . PATH_SEPARATOR . APPLICATION_PATH . '/../library' . PATH_SEPARATOR . get_include_path() ); require_once 'Fisma.php'; require_once 'Zend/Application.php'; $application = new Zend_Application( APPLICATION_ENV, APPLICATION_PATH . '/config/application.ini' ); Fisma::setAppConfig($application->getOptions()); Fisma::initialize(Fisma::RUN_MODE_WEB_APP); $application->bootstrap()->run(); } catch (Zend_Config_Exception $zce) { // A zend config exception indicates that the application may not be installed properly echo '<h1>The application is not installed correctly</h1>'; $zceMsg = $zce->getMessage(); if (stristr($zceMsg, 'parse_ini_file') !== false) { if (stristr($zceMsg, 'application.ini') !== false) { if (stristr($zceMsg, 'No such file or directory') !== false) { echo 'The ' . APPLICATION_PATH . '/config/application.ini file is missing.'; } elseif (stristr($zceMsg, 'Permission denied') !== false) { echo 'The ' . APPLICATION_PATH . '/config/application.ini file does not have the ' . 'appropriate permissions set for the application to read it.'; } else { echo 'An ini-parsing error has occured in ' . APPLICATION_PATH . '/config/application.ini ' . '<br/>Please check this file and make sure everything is setup correctly.'; } } else if (stristr($zceMsg, 'database.ini') !== false) { if (stristr($zceMsg, 'No such file or directory') !== false) { echo 'The ' . APPLICATION_PATH . '/config/database.ini file is missing.<br/>'; echo 'If you find a database.ini.template file in the config directory, edit this file ' . 'appropriately and rename it to database.ini'; } elseif (stristr($zceMsg, 'Permission denied') !== false) { echo 'The ' . APPLICATION_PATH . '/config/database.ini file does not have the appropriate ' . 'permissions set for the application to read it.'; } else { echo 'An ini-parsing error has occured in ' . APPLICATION_PATH . '/config/database.ini ' . '<br/>Please check this file and make sure everything is setup correctly.'; } } else { echo 'An ini-parsing error has occured. <br/>Please check all configuration files and make sure ' . 'everything is setup correctly'; } } elseif (stristr($zceMsg, 'syntax error') !== false) { if (stristr($zceMsg, 'application.ini') !== false) { echo 'There is a syntax error in ' . APPLICATION_PATH . '/config/application.ini ' . '<br/>Please check this file and make sure everything is setup correctly.'; } elseif (stristr($zceMsg, 'database.ini') !== false) { echo 'There is a syntax error in ' . APPLICATION_PATH . '/config/database.ini ' . '<br/>Please check this file and make sure everything is setup correctly.'; } else { echo 'A syntax error has been reached. <br/>Please check all configuration files and make sure ' . 'everything is setup correctly.'; } } else { // Then the exception message says nothing about parse_ini_file nor 'syntax error' echo 'Please check all configuration files, and ensure all settings are valid.'; } echo '<br/>For more information and help on installing OpenFISMA, please refer to the ' . '<a target="_blank" href="http://manual.openfisma.org/display/ADMIN/Installation">' . 'Installation Guide</a>'; } catch (Doctrine_Manager_Exception $dme) { echo '<h1>An exception occurred while bootstrapping the application.</h1>'; // Does database.ini have valid settings? Or is it the same content as database.ini.template? $databaseIniFail = false; $iniData = file(APPLICATION_PATH . '/config/database.ini'); $iniData = str_replace(chr(10), '', $iniData); if (in_array('db.adapter = ##DB_ADAPTER##', $iniData)) { $databaseIniFail = true; } if (in_array('db.host = ##DB_HOST##', $iniData)) { $databaseIniFail = true; } if (in_array('db.port = ##DB_PORT##', $iniData)) { $databaseIniFail = true; } if (in_array('db.username = ##DB_USER##', $iniData)) { $databaseIniFail = true; } if (in_array('db.password = ##DB_PASS##', $iniData)) { $databaseIniFail = true; } if (in_array('db.schema = ##DB_NAME##', $iniData)) { $databaseIniFail = true; } if ($databaseIniFail) { echo 'You have not applied the settings in ' . APPLICATION_PATH . '/config/database.ini appropriately. ' . 'Please review the contents of this file and try again.'; } else { if (Fisma::debug()) { echo '<p>' . get_class($dme) . '</p><p>' . $dme->getMessage() . '</p><p>' . "<p><pre>Stack Trace:\n" . $dme->getTraceAsString() . '</pre></p>'; } else { $logString = get_class($dme) . "\n" . $dme->getMessage() . "\nStack Trace:\n" . $dme->getTraceAsString() . "\n"; Zend_Registry::get('Zend_Log')->err($logString); } } } catch (Exception $exception) { // If a bootstrap exception occurs, that indicates a serious problem, such as a syntax error. // We won't be able to do anything except display an error. echo '<h1>An exception occurred while bootstrapping the application.</h1>'; if (Fisma::debug()) { echo '<p>' . get_class($exception) . '</p><p>' . $exception->getMessage() . '</p><p>' . "<p><pre>Stack Trace:\n" . $exception->getTraceAsString() . '</pre></p>'; } else { $logString = get_class($exception) . "\n" . $exception->getMessage() . "\nStack Trace:\n" . $exception->getTraceAsString() . "\n"; Zend_Registry::get('Zend_Log')->err($logString); } }

  Read the article

• How to fix “Microsoft SharePoint is not supported with version 4.0.30319.225 of the Microsoft .Net Runtime” in PowerGUI

  - by ybbest

  Today, when I try to run some PowerShell command against SharePoint in PowerGUI , I encounter some error message as below: Problem: Remove-SPSite : Microsoft SharePoint is not supported with version 4.0.30319.225 of the Microsoft .Net Runtime. At C:\SiteCreation.ps1:37 char:14 + CategoryInfo : InvalidData: (Microsoft.Share…mdletRemoveSite:SPCmdletRemoveSite) [Remove-SPSite], PlatformNotSupportedException Analysis: The error message is pretty clear that PowerGUI try to run the PowerShell command under .Net version 4.0 which is not supported by SharePoint2010, SharePoint2010 only support .Net 3.5.So how can I change the settings so that PowerShell does run under .Net3.5 in PowerGui? The solution is pretty easy. Solution: 1. Open your windows explorer and navigate to C:\Program Files (x86)\PowerGUI\ and open the configuration file ScriptEditor.exe.config. 2. Change the supportedRuntime version under Startup settings by removing the version=”v4.0″ as below From To   3. Restart your PowerGUI and rerun your script. It works like a charm.

  Read the article

• New Skool Crosstabbing

  - by Tim Dexter

  A while back I spoke about having to go back to BIP's original crosstabbing solution to achieve a certain layout. Hok Min has provided a 'man' page for the new crosstab/pivot builder for 10.1.3.4.1 users. This will make the documentation drop but for now, get it here! The old, hand method is still available but this new approach, is more efficient and flexible. That said you may need to get into the crosstab code to tweak it where the crosstab dialog can not help. I had to do this, this week but more on that later. The following explains how the crosstab wizard builds the crosstab and what the fields inside the resulting template structure are there for. To create the crosstab a new XDO command "<?crosstab:...?>" has been created. XDO Command: <?crosstab: ctvarname; data-element; rows; columns; measures; aggregation?> Parameter Description Example Ctvarname Crosstab variable name. This is automatically generated by the Add-in. C123 data-element This is the XML data element that contains the data. "//ROW" Rows This contains a list of XML elements for row headers. The ordering information is specified within "{" and "}". The first attribute is the sort element. Leaving it blank means the sort element is the same as the row header element. The attribute "o" means order. Its value can be "a" for ascending, or "d" for descending. The attribute "t" means type. Its value can be "t" for text, and "n" for numeric. There can be more than one sort elements, example: "emp-full-name {emp-lastname,o=a,t=n}{emp-firstname,o=a,t=n}. This will sort employee by last name and first name. "Region{,o=a,t=t}, District{,o=a,t=t}" In the example, the first row header is "Region". It is sort by "Region", order is ascending, and type is text. The second row header is "District". It is sort by "District", order is ascending, and type is text. Columns This contains a list of XML elements for columns headers. The ordering information is specified within "{" and "}". The first attribute is the sort element. Leaving it blank means the sort element is the same as the column header element. The attribute "o" means order. Its value can be "a" for ascending, or "d" for descending. The attribute "t" means type. Its value can be "t" for text, and "n" for numeric. There can be more than one sort elements, example: "emp-full-name {emp-lastname,o=a,t=n}{emp-firstname,o=a,t=n}. This will sort employee by last name and first name. "ProductsBrand{,o=a,t=t}, PeriodYear{,o=a,t=t}" In the example, the first column header is "ProductsBrand". It is sort by "ProductsBrand", order is ascending, and type is text. The second column header is "PeriodYear". It is sort by "District", order is ascending, and type is text. Measures This contains a list of XML elements for measures. "Revenue, PrevRevenue" Aggregation The aggregation function name. Currently, we only support "sum". "sum" Using the Oracle BI Publisher Template Builder for Word add-in, we are able to construct the following Pivot Table: The generated XDO command for this Pivot Table is as follow: <?crosstab:c547; "//ROW";"Region{,o=a,t=t}, District{,o=a,t=t}"; "ProductsBrand{,o=a,t=t},PeriodYear{,o=a,t=t}"; "Revenue, PrevRevenue";"sum"?> Running the command on the give XML data files generates this XML file "cttree.xml". Each XPath in the "cttree.xml" is described in the following table. Element XPath Count Description C0 /cttree/C0 1 This contains elements which are related to column. C1 /cttree/C0/C1 4 The first level column "ProductsBrand". There are four distinct values. They are shown in the label H element. CS /cttree/C0/C1/CS 4 The column-span value. It is used to format the crosstab table. H /cttree/C0/C1/H 4 The column header label. There are four distinct values "Enterprise", "Magicolor", "McCloskey" and "Valspar". T1 /cttree/C0/C1/T1 4 The sum for measure 1, which is Revenue. T2 /cttree/C0/C1/T2 4 The sum for measure 2, which is PrevRevenue. C2 /cttree/C0/C1/C2 8 The first level column "PeriodYear", which is the second group-by key. There are two distinct values "2001" and "2002". H /cttree/C0/C1/C2/H 8 The column header label. There are two distinct values "2001" and "2002". Since it is under C1, therefore the total number of entries is 4 x 2 => 8. T1 /cttree/C0/C1/C2/T1 8 The sum for measure 1 "Revenue". T2 /cttree/C0/C1/C2/T2 8 The sum for measure 2 "PrevRevenue". M0 /cttree/M0 1 This contains elements which are related to measures. M1 /cttree/M0/M1 1 This contains summary for measure 1. H /cttree/M0/M1/H 1 The measure 1 label, which is "Revenue". T /cttree/M0/M1/T 1 The sum of measure 1 for the entire xpath from "//ROW". M2 /cttree/M0/M2 1 This contains summary for measure 2. H /cttree/M0/M2/H 1 The measure 2 label, which is "PrevRevenue". T /cttree/M0/M2/T 1 The sum of measure 2 for the entire xpath from "//ROW". R0 /cttree/R0 1 This contains elements which are related to row. R1 /cttree/R0/R1 4 The first level row "Region". There are four distinct values, they are shown in the label H element. H /cttree/R0/R1/H 4 This is row header label for "Region". There are four distinct values "CENTRAL REGION", "EASTERN REGION", "SOUTHERN REGION" and "WESTERN REGION". RS /cttree/R0/R1/RS 4 The row-span value. It is used to format the crosstab table. T1 /cttree/R0/R1/T1 4 The sum of measure 1 "Revenue" for each distinct "Region" value. T2 /cttree/R0/R1/T2 4 The sum of measure 1 "Revenue" for each distinct "Region" value. R1C1 /cttree/R0/R1/R1C1 16 This contains elements from combining R1 and C1. There are 4 distinct values for "Region", and four distinct values for "ProductsBrand". Therefore, the combination is 4 X 4 è 16. T1 /cttree/R0/R1/R1C1/T1 16 The sum of measure 1 "Revenue" for each combination of "Region" and "ProductsBrand". T2 /cttree/R0/R1/R1C1/T2 16 The sum of measure 2 "PrevRevenue" for each combination of "Region" and "ProductsBrand". R1C2 /cttree/R0/R1/R1C1/R1C2 32 This contains elements from combining R1, C1 and C2. There are 4 distinct values for "Region", and four distinct values for "ProductsBrand", and two distinct values of "PeriodYear". Therefore, the combination is 4 X 4 X 2 è 32. T1 /cttree/R0/R1/R1C1/R1C2/T1 32 The sum of measure 1 "Revenue" for each combination of "Region", "ProductsBrand" and "PeriodYear". T2 /cttree/R0/R1/R1C1/R1C2/T2 32 The sum of measure 2 "PrevRevenue" for each combination of "Region", "ProductsBrand" and "PeriodYear". R2 /cttree/R0/R1/R2 18 This contains elements from combining R1 "Region" and R2 "District". Since the list of values in R2 has dependency on R1, therefore the number of entries is not just a simple multiplication. H /cttree/R0/R1/R2/H 18 The row header label for R2 "District". R1N /cttree/R0/R1/R2/R1N 18 The R2 position number within R1. This is used to check if it is the last row, and draw table border accordingly. T1 /cttree/R0/R1/R2/T1 18 The sum of measure 1 "Revenue" for each combination "Region" and "District". T2 /cttree/R0/R1/R2/T2 18 The sum of measure 2 "PrevRevenue" for each combination of "Region" and "District". R2C1 /cttree/R0/R1/R2/R2C1 72 This contains elements from combining R1, R2 and C1. T1 /cttree/R0/R1/R2/R2C1/T1 72 The sum of measure 1 "Revenue" for each combination of "Region", "District" and "ProductsBrand". T2 /cttree/R0/R1/R2/R2C1/T2 72 The sum of measure 2 "PrevRevenue" for each combination of "Region", "District" and "ProductsBrand". R2C2 /cttree/R0/R1/R2/R2C1/R2C2 144 This contains elements from combining R1, R2, C1 and C2, which gives the finest level of details. M1 /cttree/R0/R1/R2/R2C1/R2C2/M1 144 The sum of measure 1 "Revenue". M2 /cttree/R0/R1/R2/R2C1/R2C2/M2 144 The sum of measure 2 "PrevRevenue". Lots to read and digest I know! Customization One new feature I discovered this week is the ability to show one column and sort by another. I had a data set that was extracting month abbreviations, we wanted to show the months across the top and some row headers to the side. As you may know XSL is not great with dates, especially recognising month names. It just wants to sort them alphabetically, so Apr comes before Jan, etc. A way around this is to generate a month number alongside the month and use that to sort. We can do that in the crosstab, sadly its not exposed in the UI yet but its doable. Go back up and take a look a the initial crosstab command. especially the Rows and Columns entries. In there you will find the sort criteria. "ProductsBrand{,o=a,t=t}, PeriodYear{,o=a,t=t}" Notice those leading commas inside the curly braces? Because there is no field preceding them it means that the crosstab should sort on the column before the brace ie PeriodYear. But you can insert another column in the data set to sort by. To get my sort working how I needed. <?crosstab:c794;"current-group()";"_Fund_Type_._Fund_Type_Display_{_Fund_Type_._Fund_Type_Sort_,o=a,t=n}";"_Fiscal_Period__Amount__._Amt_Fm_Disp_Abbr_{_Fiscal_Period__Amount__._Amt_Fiscal_Month_Sort_,o=a,t=n}";"_Execution_Facts_._Amt_";"sum"?> Excuse the horribly verbose XML tags, good ol BIEE :0) The emboldened columns are not in the crosstab but are in the data set. I just opened up the field, dropped them in and changed the type(t) value to be 'n', for number, instead of the default 'a' and my crosstab started sorting how I wanted it. If you find other tips and tricks, please share in the comments.

  Read the article

• using Generics in C# [closed]

  - by Uphaar Goyal

  I have started looking into using generics in C#. As an example what i have done is that I have an abstract class which implements generic methods. these generic methods take a sql query, a connection string and the Type T as parameters and then construct the data set, populate the object and return it back. This way each business object does not need to have a method to populate it with data or construct its data set. All we need to do is pass the type, the sql query and the connection string and these methods do the rest.I am providing the code sample here. I am just looking to discuss with people who might have a better solution to what i have done. using System; using System.Collections.Generic; using System.Linq; using System.Text; using System.Data; using System.Data.SqlClient; using MWTWorkUnitMgmtLib.Business; using System.Collections.ObjectModel; using System.Reflection; namespace MWTWorkUnitMgmtLib.TableGateway { public abstract class TableGateway { public TableGateway() { } protected abstract string GetConnection(); protected abstract string GetTableName(); public DataSet GetDataSetFromSql(string connectionString, string sql) { DataSet ds = null; using (SqlConnection connection = new SqlConnection(connectionString)) using (SqlCommand command = connection.CreateCommand()) { command.CommandText = sql; connection.Open(); using (ds = new DataSet()) using (SqlDataAdapter adapter = new SqlDataAdapter(command)) { adapter.Fill(ds); } } return ds; } public static bool ContainsColumnName(DataRow dr, string columnName) { return dr.Table.Columns.Contains(columnName); } public DataTable GetDataTable(string connString, string sql) { DataSet ds = GetDataSetFromSql(connString, sql); DataTable dt = null; if (ds != null) { if (ds.Tables.Count 0) { dt = ds.Tables[0]; } } return dt; } public T Construct(DataRow dr, T t) where T : class, new() { Type t1 = t.GetType(); PropertyInfo[] properties = t1.GetProperties(); foreach (PropertyInfo property in properties) { if (ContainsColumnName(dr, property.Name) && (dr[property.Name] != null)) property.SetValue(t, dr[property.Name], null); } return t; } public T GetByID(string connString, string sql, T t) where T : class, new() { DataTable dt = GetDataTable(connString, sql); DataRow dr = dt.Rows[0]; return Construct(dr, t); } public List GetAll(string connString, string sql, T t) where T : class, new() { List collection = new List(); DataTable dt = GetDataTable(connString, sql); foreach (DataRow dr in dt.Rows) collection.Add(Construct(dr, t)); return collection; } } }

  Read the article

• Packing a DBF

  - by Tom Hines

  I thought my days of dealing with DBFs as a "production data" source were over, but HA (no such luck). I recently had to retrieve, modify and replace some data that needed to be delivered in a DBF file. Everything was fine until I realized / remembered the DBF driver does not ACTUALLY delete records from the data source -- it only marks them for deletion.  You are responsible for handling the "chaff" either by using a utility to remove deleted records or by simply ignoring them.  If imported into Excel, the marked-deleted records are ignored, but the file size will reflect the extra content.  After several rounds of testing CRUD, the output DBF was huge. So, I went hunting for a method to "Pack" the records (removing deleted ones and resizing the DBF file) and eventually ran across the FOXPRO driver at ( http://msdn.microsoft.com/en-us/vfoxpro/bb190233.aspx ).  Once installed, I changed the DSN in the code to the new one I created in the ODBC Administrator and ran some tests.  Using MSQuery, I simply tested the raw SQL command Pack {tablename} and it WORKED! One really neat thing is the PACK command is used like regular SQL instructions; "Pack {tablename}" is all that is needed. It is necessary, however, to close all connections to the database (and re-open) before issuing the PACK command or you will get the "File is in use" error.    Here is some C# code for a Pack method.         /// <summary>       /// Pack the DBF removing all deleted records       /// </summary>       /// <param name="strTableName">The table to pack</param>       /// <param name="strError">output of any errors</param>       /// <returns>bool (true if no errors)</returns>       public static bool Pack(string strTableName, ref string strError)       {          bool blnRetVal = true;          try          {             OdbcConnectionStringBuilder csbOdbc = new OdbcConnectionStringBuilder()             {                Dsn = "PSAP_FOX_DBF"             };             string strSQL = "pack " + strTableName;             using (OdbcConnection connOdbc = new OdbcConnection(csbOdbc.ToString()))             {                connOdbc.Open();                OdbcCommand cmdOdbc = new OdbcCommand(strSQL, connOdbc);                cmdOdbc.ExecuteNonQuery();                connOdbc.Close();             }          }          catch (Exception exc)          {             blnRetVal = false;             strError = exc.Message;          }          return blnRetVal;       }

  Read the article

• Packing a DBF

  - by Tom Hines

  I thought my days of dealing with DBFs as a "production data" source were over, but HA (no such luck). I recently had to retrieve, modify and replace some data that needed to be delivered in a DBF file. Everything was fine until I realized / remembered the DBF driver does not ACTUALLY delete records from the data source -- it only marks them for deletion.  You are responsible for handling the "chaff" either by using a utility to remove deleted records or by simply ignoring them.  If imported into Excel, the marked-deleted records are ignored, but the file size will reflect the extra content. So, I went hunting for a method to "Pack" the records (removing deleted ones and resizing the DBF file) and eventually ran across the FOXPRO driver at ( http://msdn.microsoft.com/en-us/vfoxpro/bb190233.aspx ).  Once installed, I changed the DSN in the code to the new one I created in the ODBC Administrator and ran some tests.  Using MSQuery, I simply tested the raw SQL command Pack {tablename} and it WORKED! One really neat thing is the PACK command is used like regular SQL instructions; "Pack {tablename}" is all that is needed. It is necessary, however, to close all connections to the database before issuing the PACK command.    Here is some C# code for a Pack method.         /// <summary>       /// Pack the DBF removing all deleted records       /// </summary>       /// <param name="strTableName">The table to pack</param>       /// <param name="strError">output of any errors</param>       /// <returns>bool (true if no errors)</returns>       public static bool Pack(string strTableName, ref string strError)       {          bool blnRetVal = true;          try          {             OdbcConnectionStringBuilder csbOdbc = new OdbcConnectionStringBuilder()             {                Dsn = "PSAP_FOX_DBF"             };             string strSQL = "pack " + strTableName;             using (OdbcConnection connOdbc = new OdbcConnection(csbOdbc.ToString()))             {                connOdbc.Open();                OdbcCommand cmdOdbc = new OdbcCommand(strSQL, connOdbc);                cmdOdbc.ExecuteNonQuery();                connOdbc.Close();             }          }          catch (Exception exc)          {             blnRetVal = false;             strError = exc.Message;          }          return blnRetVal;       }

  Read the article

• Hosting a website on Heroku.... I know how to, but im running into problems!

  - by Thomas Miller

  I'm starting to learn more on the back-end scale of programing. Recently I started up Heroku for the second or third time. This time I actually installed the Git update to my Mac and installed Heroku in the terminal. I wanted to upload a static html site with the sinatra gem. Everything worked out fine inside the terminal, though I added sinatra after I got everything working and the file with the site hooked up to Heroku. In my logs I did see that I was missing the sinatra gem, so I installed it. My site contains both the proper app.rb and config.ru files. I have nothing showing up online. Just a blank screen! Contacting Heroku on this problem has been very difficult. I get a responce every day, and on every day I respond with a question to the answer that didn't help me at all. 2011-05-18T00:25:20+00:00 app[web.1]: 71.198.0.51 - - [17/May/2011 17:25:20] "GET /favicon.ico HTTP/1.1" 404 18 0.0008 2011-05-18T00:25:20+00:00 heroku[router]: GET pxlc.heroku.com/favicon.ico dyno=web.1 queue=0 wait=0ms service=2ms bytes=313 2011-05-18T00:25:26+00:00 app[web.1]: 71.198.0.51 - - [17/May/2011 17:25:26] "GET /favicon.ico HTTP/1.1" 404 18 0.0008 2011-05-18T00:25:26+00:00 heroku[router]: GET pxlc.heroku.com/favicon.ico dyno=web.1 queue=0 wait=0ms service=5ms bytes=313 2011-05-17T18:25:51-07:00 heroku[web.1]: Idling 2011-05-17T18:26:01-07:00 heroku[web.1]: State changed from up to down 2011-05-18T01:26:01+00:00 heroku[web.1]: Stopping process with SIGTERM 2011-05-18T01:26:01+00:00 app[web.1]: Stopping ... 2011-05-18T01:26:02+00:00 heroku[web.1]: Process exited 2011-05-17T20:12:46-07:00 heroku[web.1]: Unidling 2011-05-17T20:12:47-07:00 heroku[web.1]: State changed from created to starting 2011-05-18T03:12:48+00:00 heroku[web.1]: Starting process with command: thin -p 40055 -e production -R /home/heroku_rack/heroku.ru start 2011-05-18T03:12:49+00:00 app[web.1]: Thin web server (v1.2.6 codename Crazy Delicious) 2011-05-18T03:12:49+00:00 app[web.1]: Maximum connections set to 1024 2011-05-18T03:12:49+00:00 app[web.1]: Listening on 0.0.0.0:40055, CTRL+C to stop 2011-05-18T03:12:50+00:00 heroku[router]: GET pxlc.heroku.com/ dyno=web.1 queue=0 wait=9954ms service=6ms bytes=565 2011-05-18T03:12:50+00:00 app[web.1]: 70.91.206.114 - - [17/May/2011 20:12:50] "GET /style.css HTTP/1.1" 200 - 0.0012 2011-05-18T03:12:50+00:00 heroku[router]: GET pxlc.heroku.com/style.css dyno=web.1 queue=0 wait=0ms service=2ms bytes=269 2011-05-17T20:12:50-07:00 heroku[web.1]: State changed from starting to up 2011-05-18T03:12:51+00:00 app[web.1]: 70.91.206.114 - - [17/May/2011 20:12:51] "GET /favicon.ico HTTP/1.1" 404 18 0.0008 2011-05-18T03:12:51+00:00 heroku[router]: GET pxlc.heroku.com/favicon.ico dyno=web.1 queue=0 wait=0ms service=4ms bytes=313 2011-05-18T03:13:05+00:00 heroku[router]: GET pxlc.heroku.com/ dyno=web.1 queue=0 wait=0ms service=5ms bytes=565 2011-05-18T03:13:05+00:00 app[web.1]: 70.91.206.114 - - [17/May/2011 20:13:05] "GET / HTTP/1.1" 200 293 0.0011 2011-05-18T03:13:05+00:00 heroku[router]: GET pxlc.heroku.com/favicon.ico dyno=web.1 queue=0 wait=0ms service=2ms bytes=313 2011-05-18T03:13:05+00:00 app[web.1]: 70.91.206.114 - - [17/May/2011 20:13:05] "GET /favicon.ico HTTP/1.1" 404 18 0.0007 2011-05-18T03:57:05+00:00 app[web.1]: 172.18.33.56, 58.96.134.66 - - [17/May/2011 20:57:05] "GET / HTTP/1.1" 200 293 0.0007 2011-05-18T03:57:05+00:00 heroku[router]: GET pxlc.heroku.com/ dyno=web.1 queue=0 wait=0ms service=4ms bytes=565 2011-05-18T03:57:05+00:00 app[web.1]: 172.18.33.56, 58.96.134.66 - - [17/May/2011 20:57:05] "GET /style.css HTTP/1.1" 200 - 0.0007 2011-05-18T03:57:05+00:00 heroku[router]: GET pxlc.heroku.com/style.css dyno=web.1 queue=0 wait=0ms service=2ms bytes=269 2011-05-18T03:57:08+00:00 app[web.1]: 172.18.33.56, 58.96.134.66 - - [17/May/2011 20:57:08] "GET /favicon.ico HTTP/1.1" 404 18 0.0008 2011-05-17T21:58:27-07:00 heroku[web.1]: Idling 2011-05-18T04:58:30+00:00 heroku[web.1]: Stopping process with SIGTERM 2011-05-18T04:58:30+00:00 app[web.1]: Stopping ... 2011-05-18T04:58:30+00:00 heroku[web.1]: Process exited 2011-05-17T21:58:33-07:00 heroku[web.1]: State changed from up to down 2011-05-17T23:11:58-07:00 heroku[web.1]: Unidling 2011-05-17T23:11:58-07:00 heroku[web.1]: State changed from created to starting 2011-05-18T06:12:00+00:00 heroku[web.1]: Starting process with command: thin -p 40091 -e production -R /home/heroku_rack/heroku.ru start 2011-05-18T06:12:01+00:00 app[web.1]: Thin web server (v1.2.6 codename Crazy Delicious) 2011-05-18T06:12:01+00:00 app[web.1]: Maximum connections set to 1024 2011-05-18T06:12:01+00:00 app[web.1]: Listening on 0.0.0.0:40091, CTRL+C to stop 2011-05-18T06:12:01+00:00 app[web.1]: 183.97.156.226 - - [17/May/2011 23:12:01] "GET / HTTP/1.1" 200 293 0.0017 2011-05-18T06:12:02+00:00 heroku[router]: GET pxlc.heroku.com/ dyno=web.1 queue=0 wait=3209ms service=5ms bytes=565 2011-05-18T06:12:03+00:00 app[web.1]: 183.97.156.226 - - [17/May/2011 23:12:03] "GET /style.css HTTP/1.1" 200 - 0.0019 2011-05-17T23:12:08-07:00 heroku[web.1]: State changed from starting to up 2011-05-18T00:13:13-07:00 heroku[web.1]: Idling 2011-05-18T00:13:16-07:00 heroku[web.1]: State changed from up to down 2011-05-18T07:13:16+00:00 heroku[web.1]: Stopping process with SIGTERM 2011-05-18T07:13:16+00:00 app[web.1]: Stopping ... 2011-05-18T07:13:17+00:00 heroku[web.1]: Process exited 2011-05-18T01:54:21-07:00 heroku[web.1]: Unidling 2011-05-18T01:54:21-07:00 heroku[web.1]: State changed from created to starting 2011-05-18T08:54:23+00:00 heroku[web.1]: Starting process with command: thin -p 59491 -e production -R /home/heroku_rack/heroku.ru start 2011-05-18T08:54:24+00:00 app[web.1]: Thin web server (v1.2.6 codename Crazy Delicious) 2011-05-18T08:54:24+00:00 app[web.1]: Maximum connections set to 1024 2011-05-18T08:54:24+00:00 app[web.1]: Listening on 0.0.0.0:59491, CTRL+C to stop 2011-05-18T01:54:28-07:00 heroku[web.1]: State changed from starting to up 2011-05-18T08:54:28+00:00 heroku[router]: GET pxlc.heroku.com/ dyno=web.1 queue=0 wait=6943ms service=6ms bytes=565 2011-05-18T08:54:28+00:00 app[web.1]: 62.244.82.72 - - [18/May/2011 01:54:28] "GET / HTTP/1.1" 200 293 0.0018 2011-05-18T08:54:28+00:00 heroku[router]: GET pxlc.heroku.com/style.css dyno=web.1 queue=0 wait=0ms service=2ms bytes=269 2011-05-18T08:54:28+00:00 app[web.1]: 62.244.82.72 - - [18/May/2011 01:54:28] "GET /style.css HTTP/1.1" 200 - 0.0014 2011-05-18T08:54:28+00:00 app[web.1]: 62.244.82.72 - - [18/May/2011 01:54:28] "GET /favicon.ico HTTP/1.1" 404 18 0.0008 2011-05-18T08:54:28+00:00 heroku[router]: GET pxlc.heroku.com/favicon.ico dyno=web.1 queue=0 wait=0ms service=1ms bytes=313 2011-05-18T08:54:28+00:00 heroku[router]: GET pxlc.heroku.com/favicon.ico dyno=web.1 queue=0 wait=0ms service=4ms bytes=313 2011-05-18T08:54:28+00:00 app[web.1]: 62.244.82.72 - - [18/May/2011 01:54:28] "GET /favicon.ico HTTP/1.1" 404 18 0.0008 2011-05-18T08:54:28+00:00 app[web.1]: 62.244.82.72 - - [18/May/2011 01:54:28] "GET /favicon.ico HTTP/1.1" 404 18 0.0008 2011-05-18T08:54:28+00:00 heroku[router]: GET pxlc.heroku.com/favicon.ico dyno=web.1 queue=0 wait=0ms service=1ms bytes=313 2011-05-18T02:55:23-07:00 heroku[web.1]: Idling 2011-05-18T02:55:33-07:00 heroku[web.1]: State changed from up to down 2011-05-18T09:55:34+00:00 heroku[web.1]: Stopping process with SIGTERM 2011-05-18T09:55:34+00:00 app[web.1]: Stopping ... 2011-05-18T09:55:34+00:00 heroku[web.1]: Process exited 2011-05-18T07:23:10-07:00 heroku[web.1]: State changed from created to starting 2011-05-18T14:23:12+00:00 heroku[web.1]: Starting process with command: thin -p 20560 -e production -R /home/heroku_rack/heroku.ru start 2011-05-18T14:23:13+00:00 app[web.1]: Thin web server (v1.2.6 codename Crazy Delicious) 2011-05-18T14:23:13+00:00 app[web.1]: Maximum connections set to 1024 2011-05-18T14:23:13+00:00 app[web.1]: Listening on 0.0.0.0:20560, CTRL+C to stop 2011-05-18T07:23:13-07:00 heroku[web.1]: State changed from starting to up 2011-05-18T14:23:14+00:00 app[web.1]: 12.183.19.10 - - [18/May/2011 07:23:14] "GET / HTTP/1.1" 200 293 0.0018 2011-05-18T14:23:14+00:00 heroku[router]: GET pxlc.heroku.com/ dyno=web.1 queue=0 wait=0ms service=7ms bytes=565 2011-05-18T14:23:14+00:00 app[web.1]: 12.183.19.10 - - [18/May/2011 07:23:14] "GET /style.css HTTP/1.1" 200 - 0.0015 2011-05-18T14:23:14+00:00 heroku[router]: GET pxlc.heroku.com/style.css dyno=web.1 queue=0 wait=0ms service=2ms bytes=269 2011-05-18T14:23:14+00:00 app[web.1]: 12.183.19.10 - - [18/May/2011 07:23:14] "GET /favicon.ico HTTP/1.1" 404 18 0.0009 2011-05-18T14:23:14+00:00 heroku[router]: GET pxlc.heroku.com/favicon.ico dyno=web.1 queue=0 wait=0ms service=2ms bytes=313 2011-05-18T08:24:03-07:00 heroku[web.1]: Idling 2011-05-18T08:24:07-07:00 heroku[web.1]: State changed from up to down 2011-05-18T15:24:07+00:00 heroku[web.1]: Stopping process with SIGTERM 2011-05-18T15:24:07+00:00 app[web.1]: Stopping ... 2011-05-18T17:34:27-07:00 heroku[web.1]: Unidling 2011-05-18T17:34:28-07:00 heroku[web.1]: State changed from created to starting 2011-05-19T00:34:29+00:00 heroku[web.1]: Starting process with command: thin -p 57621 -e production -R /home/heroku_rack/heroku.ru start 2011-05-18T17:34:31-07:00 heroku[web.1]: State changed from starting to up 2011-05-19T00:34:32+00:00 heroku[router]: GET pxlc.heroku.com/ dyno=web.1 queue=0 wait=0ms service=5ms bytes=565 2011-05-19T00:34:32+00:00 app[web.1]: 97.83.58.74 - - [18/May/2011 17:34:32] "GET / HTTP/1.1" 200 293 0.0016 2011-05-19T00:34:32+00:00 app[web.1]: 97.83.58.74 - - [18/May/2011 17:34:32] "GET /style.css HTTP/1.1" 200 - 0.0011 2011-05-19T00:34:32+00:00 heroku[router]: GET pxlc.heroku.com/style.css dyno=web.1 queue=0 wait=0ms service=2ms bytes=269 2011-05-19T00:34:34+00:00 heroku[router]: GET pxlc.heroku.com/favicon.ico dyno=web.1 queue=0 wait=0ms service=4ms bytes=313 2011-05-19T00:34:34+00:00 app[web.1]: 97.83.58.74 - - [18/May/2011 17:34:34] "GET /favicon.ico HTTP/1.1" 404 18 0.0007 2011-05-18T18:35:48-07:00 heroku[web.1]: Idling 2011-05-18T18:35:51-07:00 heroku[web.1]: State changed from up to down

  Read the article

• MAAS not working

  - by Zimika

  I'm trying a whole week to make MASS to work, but no results. This is the procedure: maas createsuperuser sudo apt-get install maas-dhcp maas-import-isos apt-get install maas-enlist tftpd-hpa maas-import-isos After this I start node machine with PXE as default first boot device, and select option maas-enlist. Sistem start to installing some things, and after that on MAAS WebUI stand 1 node. But when I click on Node button on WebUI or refresh page, it show 0 node. Command cobbler system list showing: root@maas-serv:~# cobbler system list default node-3ee116ea-a8b2-11e1-a735-50e549e38206 Also, sometime this procedure register one node, but when registering second one, same problem like I described up. root@maas-serv:/var/lib/tftpboot/pxelinux.cfg# is empty, only default is there. On command maas-import-isos there is a one warning. ftpboot/images/precise-x86_64-maas-ephemeral/initrd copying images generating GPXE/PXE configuration files generating PXE menu structure warning: kernel option length exceeds 255 warning: kernel option length exceeds 255 warning: kernel option length exceeds 255 warning: kernel option length exceeds 255 copying files for distro: precise-x86_64

  Read the article

• Installing SOA Suite 11.1.1.3

  - by James Taylor

  With the release of Oracle SOA Suite 11.1.1.3 last week (28 April 2010) I thought I would attempt to implement a complete SOA Environment with SOA Suite, BPM and OSB on the WLS infrastructure. One major point of difference with the 11.1.1.3 is that is is released as a point release so you must have 11.1.1.2 installed first, then upgrade to 11.1.1.3. This post is performing the upgrade on Linux, if upgrading on windows you will need to substitute the directories and files accordingly. This post assumes that you have SOA Suite 11.1.1.2 installed already. 1. Download 11.1.1.3 software from the following site: http://www.oracle.com/technology/software/products/middleware/htdocs/fmw_11_download.html WLS 11.1.1.3   RCU 11.1.1.3 SOA Suite 11.1.1.3 OSB 11.1.1.3 Copy files to a staging area. For the purpose of this document the staging area is: /u01/stage  2. Shutdown your existing SOA Suite 11.1.1.2 environment 3. Execute the WLS 11.1.1.3 install from the stage directory. wls1033_linux32.bin 4. Choose the existing 11.1.1.2 Middleware Home 5. Ignore the security update notification 6. Accept the default products to be upgraded. 7. Upgrade of WebLogic has been completed   8. Upgrade the SOA Suite database schemas using the RCU utility. Unzip the RCU utility into the staging area and run the install ./u01/stage/rcuHome/bin/rcu 9. Drop the existing Repository and provide connection details 9. Install SOA Suite patch set 11.1.1.3. Unzip the SOA Suite patchset and execute the runInstaller with the following command. ./u01/stage/Disk1/runInstaller –jreLoc $MW_HOME/jdk160_18/jre 10. Choose the existing 11.1.1.2 middleware home 11. Start Install 12. Your SOA Suite Install should now be completed. Now we need to update the database repository. Login to SQLPlus as sysdba and execute the following command. SELECT version, status FROM schema_version_registry where owner = 'DEV_SOAINFRA'; the result should be similar to this: VERSION                        STATUS      OWNER ------------------------------ ----------- ------------------------------ 11.1.1.2.0                     VALID       DEV_SOAINFRA As you can see the version if these repositories are still at 11.1.1.2. 13. To upgrade these versions you have 2 options. 1 install via RCU, but this will remove any existing services. The second option is to use the Patch Set Assistant. From the $MW_HOME directory run the following command ./Oracle_SOA1/bin/psa -dbType Oracle -dbConnectString 'localhost:1521:xe' -dbaUserName sys -schemaUserName DEV_SOAINFRA 14. Install OSB. For the OSB install I did not install the IDE, or the Examples. run the runInstaller from the command line, unzip the OSB download to the stage area. ./u01/stage/osb/Disk1/runInstaller –jreLoc $MW_HOME/jdk160_18/jre 15. Choose Custom Install NOT to install the IDE (Eclipse) or Examples. 16. Unselect the, Examples and IDE checkboxes. 17. Accept the defaults and start installing. 18. Once the install has been completed configure the domain by running the Configuration Wizard. $MW_HOME/oracle_common/common/bin/config.sh You can create a new domain. In this document I will extend the soa_domain. 19. Select the following from the check list. I have selected the BPM Suite, this is unrelated to OSB but wanted it for my development purposes. To use this functionality additional license are required. 20. Configure the database connectivity. 21. Configure the database connectivity for the OSB schema. 22. Accept the defaults if installing on standard machine, if you require a cluster or advanced configuration then choose the option for you. 23. Upgrade is complete and OSB has been installed. Now you can start your environment.

  Read the article

• Clean Up the New Ubuntu Grub2 Boot Menu

  - by Trevor Bekolay

  Ubuntu adopted the new version of the Grub boot manager in version 9.10, getting rid of the old problematic menu.lst. Today we look at how to change the boot menu options in Grub2. Grub2 is a step forward in a lot of ways, and most of the annoying menu.lst issues from the past are gone. Still, if you’re not vigilant with removing old versions of the kernel, the boot list can still end up being longer than it needs to be. Note: You may have to hold the SHIFT button on your keyboard while booting up to get this menu to show. If only one operating system is installed on your computer, it may load it automatically without displaying this menu. Remove Old Kernel Entries The most common clean up task for the boot menu is to remove old kernel versions lying around on your machine. In our case we want to remove the 2.6.32-21-generic boot menu entries. In the past, this meant opening up /boot/grub/menu.lst…but with Grub2, if we remove the kernel package from our computer, Grub automatically removes those options. To remove old kernel versions, open up Synaptic Package Manager, found in the System > Administration menu. When it opens up, type the kernel version that you want to remove in the Quick search text field. The first few numbers should suffice. For each of the entries associated with the old kernel (e.g. linux-headers-2.6.32-21 and linux-image-2.6.32-21-generic), right-click and choose Mark for Complete Removal. Click the Apply button in the toolbar and then Apply in the summary window that pops up. Close Synaptic Package Manager. The next time you boot up your computer, the Grub menu will not contain the entries associated with the removed kernel version. Remove Any Option by Editing /etc/grub.d If you need more fine-grained control, or want to remove entries that are not kernel versions, you must change the files located in /etc/grub.d. /etc/grub.d contains files that hold the menu entries that used to be contained in /boot/grub/menu.lst. If you want to add new boot menu entries, you would create a new file in this folder, making sure to mark it as executable. If you want to remove boot menu entries, as we do, you would edit files in this folder. If we wanted to remove all of the memtest86+ entries, we could just make the 20_memtest86+ file non-executable, with the terminal command sudo chmod –x 20_memtest86+ Followed by the terminal command sudo update-grub Note that memtest86+ was not found by update-grub because it will only consider executable files. However, instead, we’re going to remove the Serial console 115200 entry for memtest86+… Open a terminal window Applications > Accessories > Terminal. In the terminal window, type in the command: sudo gedit /etc/grub.d/20_memtest86+ The menu entries are found at the bottom of this file. Comment out the menu entry for serial console 115200 by adding a “#” to the start of each line. Save and close this file. In the terminal window you opened, enter in the command sudo update-grub Note: If you don’t run update-grub, the boot menu options will not change! Now, the next time you boot up, that strange entry will be gone, and you’re left with a simple and clean boot menu. Conclusion While changing Grub2’s boot menu may seem overly complicated to legacy Grub masters, for normal users, Grub2 means that you won’t have to change the boot menu that often. Fortunately, if you do have to do it, the process is still pretty easy. For more detailed information about how to change entries in Grub2, this Ubuntu forum thread is a great resource. If you’re using an older version of Ubuntu, check out our article on how to clean up Ubuntu grub boot menu after upgrades. Similar Articles Productive Geek Tips Clean Up Ubuntu Grub Boot Menu After UpgradesReinstall Ubuntu Grub Bootloader After Windows Wipes it OutChange the GRUB Menu Timeout on UbuntuHow To Switch to Console Mode for Ubuntu VMware GuestSet Windows as Default OS when Dual Booting Ubuntu TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips VMware Workstation 7 Acronis Online Backup DVDFab 6 Revo Uninstaller Pro Daily Motivator (Firefox) FetchMp3 Can Download Videos & Convert Them to Mp3 Use Flixtime To Create Video Slideshows Creating a Password Reset Disk in Windows Bypass Waiting Time On Customer Service Calls With Lucyphone MELTUP – "The Beginning Of US Currency Crisis And Hyperinflation"

  Read the article

• How do you uninstall wine 1.5?

  - by jeff

  I installed Wine through the terminal using these commands: sudo add-apt-repository ppa:ubuntu-wine/ppa sudo apt-get update sudo apt-get install wine1.5 I know that I've removed at least part of wine. I removed the .wine folder in my home folder and I managed to remove the repository via this command: sudo apt-add-repository --remove ppa:ubuntu-wine/ppa Now when I try to install wine 1.4 via Ubuntu software center, it tells me I must remove these items to install wine: Microsoft windows compatibility layer (binary emulator and library) wine1.5 Microsoft windows compatibility layer (64-bit support) wine1.5-amd64 Microsoft windows compatibility layer (32-bit support) wine1.5-i386:i386 I've already tried this command: sudo apt-get --purge remove wine but it said that wine wasn't installed. Some assistance would be appreciated.

  Read the article

• How to Add a Business Card, or vCard (.vcf) File, to a Signature in Outlook 2013 Without Displaying an Image

  - by Lori Kaufman

  Whenever you add a Business Card to your signature in Outlook 2013, the Signature Editor automatically generates a picture of it and includes that in the signature as well as attaching the .vcf file. However, there is a way to leave out the image. To remove the business card image from your signature but maintain the attached .vcf file, you must make a change to the registry. NOTE: Before making changes to the registry, be sure you back it up. We also recommend creating a restore point you can use to restore your system if something goes wrong. Before changing the registry, we must add the Business Card to the signature and save it so a .vcf file of the contact is created in the Signatures folder. To do this, click the File tab. Click Options in the menu list on the left side of the Account Information screen. On the Outlook Options dialog box, click Mail in the list of options on the left side of the dialog box. On the Mail screen, click Signatures in the Compose messages section. For this example, we will create a new signature to include the .vcf file for your business card without the image. Click New below the Select signature to edit box. Enter a name for the new signature, such as Business Card, and click OK. Enter text in the signature editor and format it the way you want or insert a different image or logo. Click Business Card above the signature editor. Select the contact you want to include in the signature on the Insert Business Card dialog box and click OK. Click Save below the Select signature to edit box. This creates a .vcf file for the business card in the Signatures folder. Click on the business card image in the signature and delete it. You should only see your formatted text or other image or logo in the signature editor. Click OK to save your new signature and close the signature editor. Close Outlook as well. Now, we will open the Registry Editor to add a key and value to indicate where to find the .vcf to include in the signature we just created. If you’re running Windows 8, press the Windows Key + X to open the command menu and select Run. You can also press the Windows Key + R to directly access the Run dialog box. NOTE: In Windows 7, select Run from the Start menu. In the Open edit box on the Run dialog box, enter “regedit” (without the quotes) and click OK. If the User Account Control dialog box displays, click Yes to continue. NOTE: You may not see this dialog box, depending on your User Account Control settings. Navigate to the following registry key: HKEY_CURRENT_USER\Software\Microsoft\Office\15.0\Outlook\Signatures Make sure the Signatures key is selected. Select New | String Value from the Edit menu. NOTE: You can also right-click in the empty space in the right pane and select New | String Value from the popup menu. Rename the new value to the name of the Signature you created. For this example, we named the value Business Card. Double-click on the new value. In the Value data edit box on the Edit String dialog box, enter the value indicating the location of the .vcf file to include in the signature. The format is: <signature name>_files\<name of .vcf file> For our example, the Value data should be as follows: Business Card_files\Lori Kaufman The name of the .vcf file is generally the contact name. If you’re not sure of what to enter for the Value data for the new key value, you can check the location and name of the .vcf file. To do this, open the Outlook Options dialog box and access the Mail screen as instructed earlier in this article. However, press and hold the Ctrl key while clicking the Signatures button. The Signatures folder opens in Windows Explorer. There should be a folder in the Signatures folder named after the signature you created with “_files” added to the end. For our example, the folder is named Business Card_files. Open this folder. In this folder, you should see a .vcf file with the name of your contact as the name of the file. For our contact, the file is named Lori Kaufman.vcf. The path to the .vcf file should be the name of the folder for the signature (Business Card_files), followed by a “\”, and the name of the .vcf file without the extension (Lori Kaufman). Putting these names together, you get the path that should be entered as the Value data in the new key you created in the Registry Editor. Business Card_files\Lori Kaufman Once you’ve entered the Value data for the new key, select Exit from the File menu to close the Registry Editor. Open Outlook and click New Email on the Home tab. Click Signature in the Include section of the New Mail Message tab and select your new signature from the drop-down menu. NOTE: If you made the new signature the default signature, it will be automatically inserted into the new mail message. The .vcf file is attached to the email message, but the business card image is not included. All you will see in the body of the email message is the text or other image you included in the signature. You can also choose to include an image of your business card in a signature with no .vcf file attached.     

  Read the article

• Certificate error with Web Platform Installer

  - by findleyd

   A friend of mine was having an issue getting the Web Platform Installer to work on his Windows Server 2008 R2 box. He said there was some sort of cert error and asked me to try https://go.microsoft.com/fwlink/?LinkId=158722 on my local machine to see if I got the cert error.  I tried it and I did get a cert error on Windows 7 64bit. I happened to notice that that url simply redirects to https://www.microsoft.com/web/webpi/2.0/WebProductList.xml . Out of curiosity I dropped to a command line and tried to run .\WebPlatformInstaller.exe /? to see if there were any command line options. It gave an error that said invalid URI. So we tried running it with the product list url like: "WebPlatformInstaller.exe https://www.microsoft.com/web/webpi/2.0/WebProductList.xml" . This seems to get around the expired cert that is on go.microsoft.com.  Here's a screen shot of the error: 

  Read the article

• How to fix “The requested service, ‘net.pipe://localhost/SecurityTokenServiceApplication/appsts.svc’ could not be activated.”

  - by ybbest

  Problem: When I try to publish a SharePoint2013 workflow, I received the error: The requested service, ‘net.pipe://localhost/SecurityTokenServiceApplication/appsts.svc’ could not be activated. After that, my workflow stopped working and every time I start a work I receive the following error message: System.ApplicationException: PreconditionFailed ---> System.ApplicationException: Error in the application. --- End of inner exception stack trace --- at System.Activities.Statements.Throw.Execute(CodeActivityContext context) at System.Activities.CodeActivity.InternalExecute(ActivityInstance instance, ActivityExecutor executor, BookmarkManager bookmarkManager) at System.Activities.Runtime.ActivityExecutor.ExecuteActivityWorkItem.ExecuteBody(ActivityExecutor executor, BookmarkManager bookmarkManager, Location resultLocation) Analysis: After analysis, I found the error by visiting the http://localhost:32843/SecurityTokenServiceApplication/securitytoken.svc and the error I got on the message is                                                                                                                                              Solution: The solution is basically getting more memory to the server. For development environment, you can restart your noderunner.exe or some other services to release some memories. To verify you have enough memory    you can browse to http://localhost:32843/SecurityTokenServiceApplication/securitytoken.svc , it should return the information below. Then you can republish your workflow and it will work like a charm.

  Read the article

• How to configure a zone cluster on Solaris Cluster 4.0

  - by JuergenS

  This is a short overview on how to configure a zone cluster on Solaris Cluster 4.0. This is a little bit different as in Solaris Cluster 3.2/3.3 because Solaris Cluster 4.0 is only running on Solaris 11. The name of the zone cluster must be unique throughout the global Solaris Cluster and must be configured on a global Solaris Cluster. Please read all the requirements for zone cluster in Solaris Cluster Software Installation Guide for SC4.0. For Solaris Cluster 3.2/3.3 please refer to my previous blog Configuration steps to create a zone cluster in Solaris Cluster 3.2/3.3. A. Configure the zone cluster into the already running global clusterCheck if zone cluster can be created # cluster show-netprops to change number of zone clusters use # cluster set-netprops -p num_zoneclusters=12 Note: 12 zone clusters is the default, values can be customized! Create config file (zc1config) for zone cluster setup e.g: Configure zone cluster # clzc configure -f zc1config zc1 Note: If not using the config file the configuration can also be done manually # clzc configure zc1 Check zone configuration # clzc export zc1 Verify zone cluster # clzc verify zc1 Note: The following message is a notice and comes up on several clzc commands Waiting for zone verify commands to complete on all the nodes of the zone cluster "zc1"... Install the zone cluster # clzc install zc1 Note: Monitor the consoles of the global zone to see how the install proceed! (The output is different on the nodes) It's very important that all global cluster nodes have installed the same set of ha-cluster packages! Boot the zone cluster # clzc boot zc1 Login into non-global-zones of zone cluster zc1 on all nodes and finish Solaris installation. # zlogin -C zc1 Check status of zone cluster # clzc status zc1 Login into non-global-zones of zone cluster zc1 and configure the shell environment for root (for PATH: /usr/cluster/bin, for MANPATH: /usr/cluster/man) # zlogin -C zc1 If using additional name service configure /etc/nsswitch.conf of zone cluster non-global zones. hosts: cluster files netmasks: cluster files Configure /etc/inet/hosts of the zone cluster zones Enter all the logical hosts of non-global zones B. Add resource groups and resources to zone cluster Create a resource group in zone cluster # clrg create -n <zone-hostname-node1>,<zone-hostname-node2> app-rg Note1: Use command # cluster status for zone cluster resource group overview. Note2: You can also run all commands for zone cluster in global cluster by adding the option -Z to the command. e.g: # clrg create -Z zc1 -n <zone-hostname-node1>,<zone-hostname-node2> app-rg Set up the logical host resource for zone cluster In the global zone do: # clzc configure zc1 clzc:zc1 add net clzc:zc1:net set address=<zone-logicalhost-ip> clzc:zc1:net end clzc:zc1 commit clzc:zc1 exit Note: Check that logical host is in /etc/hosts file In zone cluster do: # clrslh create -g app-rg -h <zone-logicalhost> <zone-logicalhost>-rs Set up storage resource for zone cluster Register HAStoragePlus # clrt register SUNW.HAStoragePlus Example1) ZFS storage pool In the global zone do: Configure zpool eg: # zpool create <zdata> mirror cXtXdX cXtXdX and # clzc configure zc1 clzc:zc1 add dataset clzc:zc1:dataset set name=zdata clzc:zc1:dataset end clzc:zc1 verify clzc:zc1 commit clzc:zc1 exit Check setup with # clzc show -v zc1 In the zone cluster do: # clrs create -g app-rg -t SUNW.HAStoragePlus -p zpools=zdata app-hasp-rs Example2) HA filesystem In the global zone do: Configure SVM diskset and SVM devices. and # clzc configure zc1 clzc:zc1 add fs clzc:zc1:fs set dir=/data clzc:zc1:fs set special=/dev/md/datads/dsk/d0 clzc:zc1:fs set raw=/dev/md/datads/rdsk/d0 clzc:zc1:fs set type=ufs clzc:zc1:fs add options [logging] clzc:zc1:fs end clzc:zc1 verify clzc:zc1 commit clzc:zc1 exit Check setup with # clzc show -v zc1 In the zone cluster do: # clrs create -g app-rg -t SUNW.HAStoragePlus -p FilesystemMountPoints=/data app-hasp-rs Example3) Global filesystem as loopback file system In the global zone configure global filesystem and it to /etc/vfstab on all global nodes e.g.: /dev/md/datads/dsk/d0 /dev/md/datads/dsk/d0 /global/fs ufs 2 yes global,logging and # clzc configure zc1 clzc:zc1 add fs clzc:zc1:fs set dir=/zone/fs (zc-lofs-mountpoint) clzc:zc1:fs set special=/global/fs (globalcluster-mountpoint) clzc:zc1:fs set type=lofs clzc:zc1:fs end clzc:zc1 verify clzc:zc1 commit clzc:zc1 exit Check setup with # clzc show -v zc1 In the zone cluster do: (Create scalable rg if not already done) # clrg create -p desired_primaries=2 -p maximum_primaries=2 app-scal-rg # clrs create -g app-scal-rg -t SUNW.HAStoragePlus -p FilesystemMountPoints=/zone/fs hasp-rs More details of adding storage available in the Installation Guide for zone cluster Switch resource group and resources online in the zone cluster # clrg online -eM app-rg # clrg online -eM app-scal-rg Test: Switch of the resource group in the zone cluster # clrg switch -n zonehost2 app-rg # clrg switch -n zonehost2 app-scal-rg Add supported dataservice to zone cluster Documentation for SC4.0 is available here Example output: Appendix: To delete a zone cluster do: # clrg delete -Z zc1 -F + Note: Zone cluster uninstall can only be done if all resource groups are removed in the zone cluster. The command 'clrg delete -F +' can be used in zone cluster to delete the resource groups recursively. # clzc halt zc1 # clzc uninstall zc1 Note: If clzc command is not successful to uninstall the zone, then run 'zoneadm -z zc1 uninstall -F' on the nodes where zc1 is configured # clzc delete zc1

  Read the article

< Previous Page | 363 364 365 366 367 368 369 370 371 372 373 374  | Next Page >