Search Results

Search found 20691 results on 828 pages for 'iso image'.

Page 373/828 | < Previous Page | 369 370 371 372 373 374 375 376 377 378 379 380  | Next Page >

  • cannot make ubuntu 64-bit v12.04 install work

    - by honestann
    I decided it was time to update my ubuntu (single boot) computer from 64-bit v10.04 to 64-bit v12.04. Unfortunately, for some reason (or reasons) I just can't make it work. Note that I am attempting a fresh install of 64-bit v12.04 onto a new 3TB hard disk, not an upgrade of the 1TB hard disk that contains my working 64-bit v10.04 installation. To perform the attempted install of v12.04 I unplug the SATA cable from the 1TB drive and plug it into the 3TB drive (to avoid risking damage to my working v10.04 installation). I downloaded the ubuntu 64-bit v12.04 install DVD ISO file (~1.6 GB) from the ubuntu releases webpage and burned it onto a DVD. I have downloaded the DVD ISO file 3 times and burned 3 of these installation DVDs (twice with v10.04 and once with my winxp64 system), but none of them work. I run the "check disk" on the DVDs at the beginning of the installation process to assure the DVD is valid. When installation completes and the system boots the 3TB drive, it reports "unknown filesystem". After installation on the 250GB drives, the system boots up fine. During every install I plug the same SATA cable (sda) into only one disk drive (the 3TB or one of the 250GB drives) and leave the other disk drives unconnected (for simplicity). It is my understanding that 64-bit ubuntu (and 64-bit linux in general) has no problem with 3TB disk drives. In the BIOS I have tried having EFI set to "enabled" and "auto" with no apparent difference (no success). I never bothered setting the BIOS to "non-EFI". I have tried partitioning the drive in a few ways to see if that makes a difference, but so far it has not mattered. Typically I manually create partitions something like this: 8GB /boot ext4 8GB swap 3TB / ext4 But I've also tried the following, just in case it matters: 8GB boot efi 8GB swap 8GB /boot ext4 3TB / ext4 Note: In the partition dialog I specify bootup on the same drive I am partitioning and installing ubuntu v12.04 onto. It is a VERY DANGEROUS FACT that the default for this always comes up with the wrong drive (some other drive, generally the external drive). Unless I'm stupid or misunderstanding something, this is very wrong and very dangerous default behavior. Note: If I connect the SATA cable to the 1TB drive that has been my ubuntu 64-bit v10.04 system drive for the past 2 years, it boots up and runs fine. I guess there must be a log file somewhere, and maybe it gives some hints as to what the problem is. I should be able to boot off the 1TB drive with the 3TB drive connected as a secondary (non-boot) drive and get the log file, assuming there is one and someone tells me the name (and where to find it if the name is very generic). After installation on the 3TB drive completes and the system reboots, the following prints out on a black screen: Loading Operating System ... Boot from CD/DVD : Boot from CD/DVD : error: unknown filesystem grub rescue> Note: I have two DVD burners in the system, hence the duplicate line above. Note: I install and boot 64-bit ubuntu v12.04 on both of my 250GB in this same system, but still cannot make the 3TB drive boot. Sigh. Any ideas? ========== motherboard == gigabyte 990FXA-UD7 CPU == AMD FX-8150 8-core bulldozer @ 3.6 GHz RAM == 8GB of DDR3 in 2 sticks (matched pair) HDD == seagate 3TB SATA3 @ 7200 rpm (new install 64-bit v12.04 FAILS) HDD == seagate 1TB SATA3 @ 7200 rpm (64-bit v10.04 WORKS for two years) HDD == seagate 250GB SATA2 @ 7200 rpm (new install 64-bit v12.04 WORKS) HDD == seagate 250GB SATA2 @ 7200 rpm (new install 64-bit v12.04 WORKS) GPU == nvidia GTX-285 ??? == no overclocking or other funky business USB == external seagate 2TB HDD for making backups DVD == one bluray burner (SATA) DVD == one DVD burner (SATA) 64-bit ubuntu v10.04 has booted and run fine on the seagate 1TB drive for 2 years.

    Read the article

  • When I shutdown the computer, it restarts

    - by Prabu
    I am unable to shutdown. Whenever I try to shutdown, it reboots. I am running Ubuntu 12.10. I have run the boot-repair and this is the result: Boot Info Script 0.61.full + Boot-Repair extra info [Boot-Info November 20th 2012] ============================= Boot Info Summary: =============================== => Grub2 (v2.00) is installed in the MBR of /dev/sda and looks at sector 1 of the same hard drive for core.img. core.img is at this location and looks in partition 1 for (,msdos1)/boot/grub. sda1: __________________________________________________________________________ File system: ext4 Boot sector type: - Boot sector info: Operating System: Ubuntu 12.10 Boot files: /boot/grub/grub.cfg /etc/fstab /boot/grub/i386-pc/core.img sda2: __________________________________________________________________________ File system: Extended Partition Boot sector type: - Boot sector info: sda5: __________________________________________________________________________ File system: swap Boot sector type: - Boot sector info: ============================ Drive/Partition Info: ============================= Drive: sda _____________________________________________________________________ Disk /dev/sda: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes Partition Boot Start Sector End Sector # of Sectors Id System /dev/sda1 * 2,048 1,936,809,983 1,936,807,936 83 Linux /dev/sda2 1,936,812,030 1,953,523,711 16,711,682 5 Extended /dev/sda5 1,936,812,032 1,953,523,711 16,711,680 82 Linux swap / Solaris "blkid" output: ________________________________________________________________ Device UUID TYPE LABEL /dev/loop0 squashfs /dev/sda1 229a5484-7659-4ce1-98ce-2f05f61a1ffa ext4 /dev/sda5 6c6dca25-ab67-4de4-8602-26fdb6154781 swap /dev/sr0 iso9660 Ubuntu 12.10 amd64 ================================ Mount points: ================================= Device Mount_Point Type Options /dev/loop0 /rofs squashfs (ro,noatime) /dev/sr0 /cdrom iso9660 (ro,noatime) =========================== sda1/boot/grub/grub.cfg: =========================== -------------------------------------------------------------------------------- # # DO NOT EDIT THIS FILE # # It is automatically generated by grub-mkconfig using templates # from /etc/grub.d and settings from /etc/default/grub # ### BEGIN /etc/grub.d/00_header ### if [ -s $prefix/grubenv ]; then set have_grubenv=true load_env fi set default="0" if [ x"${feature_menuentry_id}" = xy ]; then menuentry_id_option="--id" else menuentry_id_option="" fi export menuentry_id_option if [ "${prev_saved_entry}" ]; then set saved_entry="${prev_saved_entry}" save_env saved_entry set prev_saved_entry= save_env prev_saved_entry set boot_once=true fi function savedefault { if [ -z "${boot_once}" ]; then saved_entry="${chosen}" save_env saved_entry fi } function recordfail { set recordfail=1 if [ -n "${have_grubenv}" ]; then if [ -z "${boot_once}" ]; then save_env recordfail; fi; fi } function load_video { if [ x$feature_all_video_module = xy ]; then insmod all_video else insmod efi_gop insmod efi_uga insmod ieee1275_fb insmod vbe insmod vga insmod video_bochs insmod video_cirrus fi } if [ x$feature_default_font_path = xy ] ; then font=unicode else insmod part_msdos insmod ext2 set root='hd0,msdos1' if [ x$feature_platform_search_hint = xy ]; then search --no-floppy --fs-uuid --set=root --hint-bios=hd0,msdos1 --hint-efi=hd0,msdos1 --hint-baremetal=ahci0,msdos1 229a5484-7659-4ce1-98ce-2f05f61a1ffa else search --no-floppy --fs-uuid --set=root 229a5484-7659-4ce1-98ce-2f05f61a1ffa fi font="/usr/share/grub/unicode.pf2" fi if loadfont $font ; then set gfxmode=auto load_video insmod gfxterm set locale_dir=$prefix/locale set lang=en_US insmod gettext fi terminal_output gfxterm if [ "${recordfail}" = 1 ]; then set timeout=10 else set timeout=10 fi ### END /etc/grub.d/00_header ### ### BEGIN /etc/grub.d/05_debian_theme ### set menu_color_normal=white/black set menu_color_highlight=black/light-gray if background_color 44,0,30; then clear fi ### END /etc/grub.d/05_debian_theme ### ### BEGIN /etc/grub.d/10_linux ### function gfxmode { set gfxpayload="${1}" if [ "${1}" = "keep" ]; then set vt_handoff=vt.handoff=7 else set vt_handoff= fi } if [ "${recordfail}" != 1 ]; then if [ -e ${prefix}/gfxblacklist.txt ]; then if hwmatch ${prefix}/gfxblacklist.txt 3; then if [ ${match} = 0 ]; then set linux_gfx_mode=keep else set linux_gfx_mode=text fi else set linux_gfx_mode=text fi else set linux_gfx_mode=keep fi else set linux_gfx_mode=text fi export linux_gfx_mode if [ "${linux_gfx_mode}" != "text" ]; then load_video; fi menuentry 'Ubuntu' --class ubuntu --class gnu-linux --class gnu --class os $menuentry_id_option 'gnulinux-simple-229a5484-7659-4ce1-98ce-2f05f61a1ffa' { recordfail gfxmode $linux_gfx_mode insmod gzio insmod part_msdos insmod ext2 set root='hd0,msdos1' if [ x$feature_platform_search_hint = xy ]; then search --no-floppy --fs-uuid --set=root --hint-bios=hd0,msdos1 --hint-efi=hd0,msdos1 --hint-baremetal=ahci0,msdos1 229a5484-7659-4ce1-98ce-2f05f61a1ffa else search --no-floppy --fs-uuid --set=root 229a5484-7659-4ce1-98ce-2f05f61a1ffa fi linux /boot/vmlinuz-3.5.0-19-generic root=UUID=229a5484-7659-4ce1-98ce-2f05f61a1ffa ro quiet splash acpi=force $vt_handoff initrd /boot/initrd.img-3.5.0-19-generic } submenu 'Advanced options for Ubuntu' $menuentry_id_option 'gnulinux-advanced-229a5484-7659-4ce1-98ce-2f05f61a1ffa' { menuentry 'Ubuntu, with Linux 3.5.0-19-generic' --class ubuntu --class gnu-linux --class gnu --class os $menuentry_id_option 'gnulinux-3.5.0-19-generic-advanced-229a5484-7659-4ce1-98ce-2f05f61a1ffa' { recordfail gfxmode $linux_gfx_mode insmod gzio insmod part_msdos insmod ext2 set root='hd0,msdos1' if [ x$feature_platform_search_hint = xy ]; then search --no-floppy --fs-uuid --set=root --hint-bios=hd0,msdos1 --hint-efi=hd0,msdos1 --hint-baremetal=ahci0,msdos1 229a5484-7659-4ce1-98ce-2f05f61a1ffa else search --no-floppy --fs-uuid --set=root 229a5484-7659-4ce1-98ce-2f05f61a1ffa fi echo 'Loading Linux 3.5.0-19-generic ...' linux /boot/vmlinuz-3.5.0-19-generic root=UUID=229a5484-7659-4ce1-98ce-2f05f61a1ffa ro quiet splash acpi=force $vt_handoff echo 'Loading initial ramdisk ...' initrd /boot/initrd.img-3.5.0-19-generic } menuentry 'Ubuntu, with Linux 3.5.0-19-generic (recovery mode)' --class ubuntu --class gnu-linux --class gnu --class os $menuentry_id_option 'gnulinux-3.5.0-19-generic-recovery-229a5484-7659-4ce1-98ce-2f05f61a1ffa' { recordfail insmod gzio insmod part_msdos insmod ext2 set root='hd0,msdos1' if [ x$feature_platform_search_hint = xy ]; then search --no-floppy --fs-uuid --set=root --hint-bios=hd0,msdos1 --hint-efi=hd0,msdos1 --hint-baremetal=ahci0,msdos1 229a5484-7659-4ce1-98ce-2f05f61a1ffa else search --no-floppy --fs-uuid --set=root 229a5484-7659-4ce1-98ce-2f05f61a1ffa fi echo 'Loading Linux 3.5.0-19-generic ...' linux /boot/vmlinuz-3.5.0-19-generic root=UUID=229a5484-7659-4ce1-98ce-2f05f61a1ffa ro recovery nomodeset echo 'Loading initial ramdisk ...' initrd /boot/initrd.img-3.5.0-19-generic } menuentry 'Ubuntu, with Linux 3.5.0-17-generic' --class ubuntu --class gnu-linux --class gnu --class os $menuentry_id_option 'gnulinux-3.5.0-17-generic-advanced-229a5484-7659-4ce1-98ce-2f05f61a1ffa' { recordfail gfxmode $linux_gfx_mode insmod gzio insmod part_msdos insmod ext2 set root='hd0,msdos1' if [ x$feature_platform_search_hint = xy ]; then search --no-floppy --fs-uuid --set=root --hint-bios=hd0,msdos1 --hint-efi=hd0,msdos1 --hint-baremetal=ahci0,msdos1 229a5484-7659-4ce1-98ce-2f05f61a1ffa else search --no-floppy --fs-uuid --set=root 229a5484-7659-4ce1-98ce-2f05f61a1ffa fi echo 'Loading Linux 3.5.0-17-generic ...' linux /boot/vmlinuz-3.5.0-17-generic root=UUID=229a5484-7659-4ce1-98ce-2f05f61a1ffa ro quiet splash acpi=force $vt_handoff echo 'Loading initial ramdisk ...' initrd /boot/initrd.img-3.5.0-17-generic } menuentry 'Ubuntu, with Linux 3.5.0-17-generic (recovery mode)' --class ubuntu --class gnu-linux --class gnu --class os $menuentry_id_option 'gnulinux-3.5.0-17-generic-recovery-229a5484-7659-4ce1-98ce-2f05f61a1ffa' { recordfail insmod gzio insmod part_msdos insmod ext2 set root='hd0,msdos1' if [ x$feature_platform_search_hint = xy ]; then search --no-floppy --fs-uuid --set=root --hint-bios=hd0,msdos1 --hint-efi=hd0,msdos1 --hint-baremetal=ahci0,msdos1 229a5484-7659-4ce1-98ce-2f05f61a1ffa else search --no-floppy --fs-uuid --set=root 229a5484-7659-4ce1-98ce-2f05f61a1ffa fi echo 'Loading Linux 3.5.0-17-generic ...' linux /boot/vmlinuz-3.5.0-17-generic root=UUID=229a5484-7659-4ce1-98ce-2f05f61a1ffa ro recovery nomodeset echo 'Loading initial ramdisk ...' initrd /boot/initrd.img-3.5.0-17-generic } } ### END /etc/grub.d/10_linux ### ### BEGIN /etc/grub.d/20_linux_xen ### ### END /etc/grub.d/20_linux_xen ### ### BEGIN /etc/grub.d/20_memtest86+ ### menuentry "Memory test (memtest86+)" { insmod part_msdos insmod ext2 set root='hd0,msdos1' if [ x$feature_platform_search_hint = xy ]; then search --no-floppy --fs-uuid --set=root --hint-bios=hd0,msdos1 --hint-efi=hd0,msdos1 --hint-baremetal=ahci0,msdos1 229a5484-7659-4ce1-98ce-2f05f61a1ffa else search --no-floppy --fs-uuid --set=root 229a5484-7659-4ce1-98ce-2f05f61a1ffa fi linux16 /boot/memtest86+.bin } menuentry "Memory test (memtest86+, serial console 115200)" { insmod part_msdos insmod ext2 set root='hd0,msdos1' if [ x$feature_platform_search_hint = xy ]; then search --no-floppy --fs-uuid --set=root --hint-bios=hd0,msdos1 --hint-efi=hd0,msdos1 --hint-baremetal=ahci0,msdos1 229a5484-7659-4ce1-98ce-2f05f61a1ffa else search --no-floppy --fs-uuid --set=root 229a5484-7659-4ce1-98ce-2f05f61a1ffa fi linux16 /boot/memtest86+.bin console=ttyS0,115200n8 } ### END /etc/grub.d/20_memtest86+ ### ### BEGIN /etc/grub.d/30_os-prober ### ### END /etc/grub.d/30_os-prober ### ### BEGIN /etc/grub.d/30_uefi-firmware ### ### END /etc/grub.d/30_uefi-firmware ### ### BEGIN /etc/grub.d/40_custom ### # This file provides an easy way to add custom menu entries. Simply type the # menu entries you want to add after this comment. Be careful not to change # the 'exec tail' line above. ### END /etc/grub.d/40_custom ### ### BEGIN /etc/grub.d/41_custom ### if [ -f ${config_directory}/custom.cfg ]; then source ${config_directory}/custom.cfg elif [ -z "${config_directory}" -a -f $prefix/custom.cfg ]; then source $prefix/custom.cfg; fi ### END /etc/grub.d/41_custom ### -------------------------------------------------------------------------------- =============================== sda1/etc/fstab: ================================ -------------------------------------------------------------------------------- # /etc/fstab: static file system information. # # Use 'blkid' to print the universally unique identifier for a # device; this may be used with UUID= as a more robust way to name devices # that works even if disks are added and removed. See fstab(5). # # <file system> <mount point> <type> <options> <dump> <pass> # / was on /dev/sda1 during installation UUID=229a5484-7659-4ce1-98ce-2f05f61a1ffa / ext4 errors=remount-ro 0 1 # swap was on /dev/sda5 during installation UUID=6c6dca25-ab67-4de4-8602-26fdb6154781 none swap sw 0 0 -------------------------------------------------------------------------------- =================== sda1: Location of files loaded by Grub: ==================== GiB - GB File Fragment(s) 200.155235291 = 214.915047424 boot/grub/grub.cfg 1 40.280788422 = 43.251167232 boot/initrd.img-3.5.0-17-generic 1 2.468288422 = 2.650304512 boot/initrd.img-3.5.0-19-generic 1 200.149234772 = 214.908604416 boot/vmlinuz-3.5.0-17-generic 1 1.990135193 = 2.136891392 boot/vmlinuz-3.5.0-19-generic 1 2.468288422 = 2.650304512 initrd.img 1 1.990135193 = 2.136891392 vmlinuz 1 1.990135193 = 2.136891392 vmlinuz.old 1 =============================== StdErr Messages: =============================== cat: write error: Broken pipe File descriptor 8 (/proc/6297/mounts) leaked on lvscan invocation. Parent PID 13390: bash No volume groups found ADDITIONAL INFORMATION : =================== log of boot-repair 2012-12-17__01h53 =================== boot-repair version : 3.197~ppa1~quantal boot-sav version : 3.197~ppa1~quantal glade2script version : 3.2.2~ppa45~quantal boot-sav-extra version : 3.197~ppa1~quantal boot-repair is executed in live-session (Ubuntu 12.10, quantal, Ubuntu, x86_64) CPU op-mode(s): 32-bit, 64-bit file=/cdrom/preseed/ubuntu.seed boot=casper initrd=/casper/initrd.lz quiet splash -- maybe-ubiquity =================== os-prober: /dev/sda1:Ubuntu 12.10 (12.10):Ubuntu:linux =================== blkid: /dev/loop0: TYPE="squashfs" /dev/sr0: LABEL="Ubuntu 12.10 amd64" TYPE="iso9660" /dev/sda1: UUID="229a5484-7659-4ce1-98ce-2f05f61a1ffa" TYPE="ext4" /dev/sda5: UUID="6c6dca25-ab67-4de4-8602-26fdb6154781" TYPE="swap" 1 disks with OS, 1 OS : 1 Linux, 0 MacOS, 0 Windows, 0 unknown type OS. Warning: extended partition does not start at a cylinder boundary. DOS and Linux will interpret the contents differently. =================== sda1/etc/default/grub : # If you change this file, run 'update-grub' afterwards to update # /boot/grub/grub.cfg. # For full documentation of the options in this file, see: # info -f grub -n 'Simple configuration' GRUB_DEFAULT=0 GRUB_HIDDEN_TIMEOUT=0 GRUB_HIDDEN_TIMEOUT_QUIET=true GRUB_TIMEOUT=10 GRUB_DISTRIBUTOR=`lsb_release -i -s 2> /dev/null || echo Debian` GRUB_CMDLINE_LINUX_DEFAULT="quiet splash acpi=force" GRUB_CMDLINE_LINUX="" # Uncomment to enable BadRAM filtering, modify to suit your needs # This works with Linux (no patch required) and with any kernel that obtains # the memory map information from GRUB (GNU Mach, kernel of FreeBSD ...) #GRUB_BADRAM="0x01234567,0xfefefefe,0x89abcdef,0xefefefef" # Uncomment to disable graphical terminal (grub-pc only) #GRUB_TERMINAL=console # The resolution used on graphical terminal # note that you can use only modes which your graphic card supports via VBE # you can see them in real GRUB with the command `vbeinfo' #GRUB_GFXMODE=640x480 # Uncomment if you don't want GRUB to pass "root=UUID=xxx" parameter to Linux #GRUB_DISABLE_LINUX_UUID=true # Uncomment to disable generation of recovery mode menu entries #GRUB_DISABLE_RECOVERY="true" # Uncomment to get a beep at grub start #GRUB_INIT_TUNE="480 440 1" =================== sda1/etc/grub.d/ : drwxr-xr-x 2 root root 4096 Oct 17 14:59 grub.d total 72 -rwxr-xr-x 1 root root 7541 Oct 14 17:36 00_header -rwxr-xr-x 1 root root 5488 Oct 4 09:30 05_debian_theme -rwxr-xr-x 1 root root 10891 Oct 14 17:36 10_linux -rwxr-xr-x 1 root root 10258 Oct 14 17:36 20_linux_xen -rwxr-xr-x 1 root root 1688 Oct 11 14:10 20_memtest86+ -rwxr-xr-x 1 root root 10976 Oct 14 17:36 30_os-prober -rwxr-xr-x 1 root root 1426 Oct 14 17:36 30_uefi-firmware -rwxr-xr-x 1 root root 214 Oct 14 17:36 40_custom -rwxr-xr-x 1 root root 216 Oct 14 17:36 41_custom -rw-r--r-- 1 root root 483 Oct 14 17:36 README =================== UEFI/Legacy mode: This live-session is not in EFI-mode. SecureBoot maybe enabled. =================== PARTITIONS & DISKS: sda1 : sda, not-sepboot, grubenv-ok grub2, grub-pc , update-grub, 64, with-boot, is-os, not--efi--part, fstab-without-boot, fstab-without-efi, no-nt, no-winload, no-recov-nor-hid, no-bmgr, notwinboot, apt-get, grub-install, with--usr, fstab-without-usr, not-sep-usr, standard, farbios, /mnt/boot-sav/sda1. sda : not-GPT, BIOSboot-not-needed, has-no-EFIpart, not-usb, has-os, 2048 sectors * 512 bytes =================== parted -l: Model: ATA ST1000DM003-1CH1 (scsi) Disk /dev/sda: 1000GB Sector size (logical/physical): 512B/4096B Partition Table: msdos Number Start End Size Type File system Flags 1 1049kB 992GB 992GB primary ext4 boot 2 992GB 1000GB 8556MB extended 5 992GB 1000GB 8556MB logical linux-swap(v1) Warning: Unable to open /dev/sr0 read-write (Read-only file system). /dev/sr0 has been opened read-only. Error: Can't have a partition outside the disk! =================== parted -lm: BYT; /dev/sda:1000GB:scsi:512:4096:msdos:ATA ST1000DM003-1CH1; 1:1049kB:992GB:992GB:ext4::boot; 2:992GB:1000GB:8556MB:::; 5:992GB:1000GB:8556MB:linux-swap(v1)::; Warning: Unable to open /dev/sr0 read-write (Read-only file system). /dev/sr0 has been opened read-only. Error: Can't have a partition outside the disk! =================== mount: /cow on / type overlayfs (rw) proc on /proc type proc (rw,noexec,nosuid,nodev) sysfs on /sys type sysfs (rw,noexec,nosuid,nodev) udev on /dev type devtmpfs (rw,mode=0755) devpts on /dev/pts type devpts (rw,noexec,nosuid,gid=5,mode=0620) tmpfs on /run type tmpfs (rw,noexec,nosuid,size=10%,mode=0755) /dev/sr0 on /cdrom type iso9660 (ro,noatime) /dev/loop0 on /rofs type squashfs (ro,noatime) none on /sys/fs/fuse/connections type fusectl (rw) none on /sys/kernel/debug type debugfs (rw) none on /sys/kernel/security type securityfs (rw) tmpfs on /tmp type tmpfs (rw,nosuid,nodev) none on /run/lock type tmpfs (rw,noexec,nosuid,nodev,size=5242880) none on /run/shm type tmpfs (rw,nosuid,nodev) none on /run/user type tmpfs (rw,noexec,nosuid,nodev,size=104857600,mode=0755) gvfsd-fuse on /run/user/ubuntu/gvfs type fuse.gvfsd-fuse (rw,nosuid,nodev,user=ubuntu) /dev/sda1 on /mnt/boot-sav/sda1 type ext4 (rw) =================== ls: /sys/block/sda (filtered): alignment_offset bdi capability dev device discard_alignment events events_async events_poll_msecs ext_range holders inflight power queue range removable ro sda1 sda2 sda5 size slaves stat subsystem trace uevent /sys/block/sr0 (filtered): alignment_offset bdi capability dev device discard_alignment events events_async events_poll_msecs ext_range holders inflight power queue range removable ro size slaves stat subsystem trace uevent /dev (filtered): alarm ashmem autofs binder block bsg btrfs-control bus cdrom cdrw char console core cpu cpu_dma_latency disk dri dvd dvdrw ecryptfs fb0 fd full fuse fw0 hidraw0 hidraw1 hpet input kmsg kvm log mapper mcelog mei mem net network_latency network_throughput null oldmem port ppp psaux ptmx pts random rfkill rtc rtc0 sda sda1 sda2 sda5 sg0 sg1 shm snapshot snd sr0 stderr stdin stdout uinput urandom usb vga_arbiter vhost-net zero ls /dev/mapper: control =================== df -Th: Filesystem Type Size Used Avail Use% Mounted on /cow overlayfs 3.9G 100M 3.8G 3% / udev devtmpfs 3.9G 12K 3.9G 1% /dev tmpfs tmpfs 1.6G 864K 1.6G 1% /run /dev/sr0 iso9660 763M 763M 0 100% /cdrom /dev/loop0 squashfs 717M 717M 0 100% /rofs tmpfs tmpfs 3.9G 32K 3.9G 1% /tmp none tmpfs 5.0M 4.0K 5.0M 1% /run/lock none tmpfs 3.9G 176K 3.9G 1% /run/shm none tmpfs 100M 52K 100M 1% /run/user /dev/sda1 ext4 910G 26G 838G 3% /mnt/boot-sav/sda1 =================== fdisk -l: Disk /dev/sda: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x000da1e9 Device Boot Start End Blocks Id System /dev/sda1 * 2048 1936809983 968403968 83 Linux /dev/sda2 1936812030 1953523711 8355841 5 Extended Partition 2 does not start on physical sector boundary. /dev/sda5 1936812032 1953523711 8355840 82 Linux swap / Solaris Partition outside the disk detected. =================== Recommended repair Recommended-Repair This setting will reinstall the grub2 of sda1 into the MBR of sda. Additional repair will be performed: unhide-bootmenu-10s Unhide GRUB boot menu in sda1/etc/default/grub grub-install (GRUB) 2.00-7ubuntu11,grub-install (GRUB) 2. Reinstall the GRUB of sda1 into the MBR of sda Installation finished. No error reported. grub-install /dev/sda: exit code of grub-install /dev/sda:0 chroot /mnt/boot-sav/sda1 update-grub Generating grub.cfg ... Found linux image: /boot/vmlinuz-3.5.0-19-generic Found initrd image: /boot/initrd.img-3.5.0-19-generic Found linux image: /boot/vmlinuz-3.5.0-17-generic Found initrd image: /boot/initrd.img-3.5.0-17-generic Found memtest86+ image: /boot/memtest86+.bin Unhide GRUB boot menu in sda1/boot/grub/grub.cfg Boot successfully repaired. You can now reboot your computer.

    Read the article

  • help: cannot make ubuntu 64-bit v12.04 install work

    - by honestann
    I decided it was time to update my ubuntu (single boot) computer from 64-bit v10.04 to 64-bit v12.04. Unfortunately, for some reason (or reasons) I just can't make it work. Note that I am attempting a fresh install of 64-bit v12.04 onto a new 3TB hard disk, not an upgrade of the 1TB hard disk that has contained my 64-bit v10.04 installation. To perform the attempted install of v12.04 I unplug the SATA cable from the 1TB drive and plug it into the 3TB drive (to avoid risking damage to my working v10.04 installation). I downloaded the ubuntu 64-bit v12.04 install DVD ISO file (~1.6 GB) from the ubuntu releases webpage and burned it onto a DVD. I have downloaded the DVD ISO file 3 times and burned 3 of these installation DVDs (twice with v10.04 and once with my winxp64 system), but none of them work. I run the "check disk" on the DVDs at the beginning of the installation process to assure the DVD is valid. I also tried to install on two older 250GB seagate drives in the same computer. During every attempt I plug the same SATA cable (sda) into only one disk drive (the 3TB or one of the 250GB drives) and leave the other disk drives unconnected (for simplicity). Installation takes about 30 minutes on the 250GB drives, and about 60 minutes on the 3TB drive - not sure why. When I install on the 250GB drives, the install process finishes, the computer reboots (after the install DVD is removed), but I get a grub error 15. It is my understanding that 64-bit ubuntu (and 64-bit linux in general) has no problem with 3TB disk drives. In the BIOS I have tried having EFI set to "enabled" and "auto" with no apparent difference (no success). I have tried partitioning the drive in a few ways to see if that makes a difference, but so far it has not mattered. Typically I manually create partitions something like this: 8GB swap 8GB /boot ext4 3TB / ext4 But I've also tried the following, just in case it matters: 100MB boot efi 8GB swap 8GB /boot ext4 3TB / ext4 Note: In the partition dialog I specify bootup on the same drive I am partitioning and installing ubuntu v12.04 onto. It is a VERY DANGEROUS FACT that the default for this always comes up with the wrong drive (some other drive, generally the external drive). Unless I'm stupid or misunderstanding something, this is very wrong and very dangerous default behavior. Note: If I connect the SATA cable to the 1TB drive that has been my ubuntu 64-bit v10.04 system drive for the past 2 years, it boots up and runs fine. I guess there must be a log file somewhere, and maybe it gives some hints as to what the problem is. I should be able to boot off the 1TB drive with the 3TB drive connected as a secondary (non-boot) drive and get the log file, assuming there is one and someone tells me the name (and where to find it if the name is very generic). After installation on the 3TB drive completes and the system reboots, the following prints out on a black screen: Loading Operating System ... Boot from CD/DVD : Boot from CD/DVD : error: unknown filesystem grub rescue Note: I have two DVD burners in the system, hence the duplicate line above. The same install and reboot on the 250GB drives generates "grub error 15". Sigh. Any ideas? ========== motherboard == gigabyte 990FXA-UD7 CPU == AMD FX-8150 8-core bulldozer @ 3.6 GHz RAM == 8GB of DDR3 in 2 sticks (matched pair) HDD == seagate 3TB SATA3 @ 7200 rpm (new install 64-bit v12.04) HDD == seagate 1TB SATA3 @ 7200 rpm (current install 64-bit v10.04) GPU == nvidia GTX-285 ??? == no overclocking or other funky business USB == external seagate 2TB HDD for making backups DVD == one bluray burner (SATA) DVD == one DVD burner (SATA) The current ubuntu 64-bit v10.04 system boots and runs fine on a seagate 1TB.

    Read the article

  • CodePlex Daily Summary for Wednesday, November 21, 2012

    CodePlex Daily Summary for Wednesday, November 21, 2012Popular ReleasesImapX 2: ImapX 2.0.0.6: An updated release of the ImapX 2 library, containing many bugfixes for both, the library and the sample application.Metodología General Ajustada - MGA: 03.05.05: Cambios John: Se modificó el Procedimiento Alamacenado PROF03ObjetivoProductoConsultarIdF03 que no incluía los campos de IdUnidadMedida y UnidadMedida, lo que generaba error en la capa de datos al leer estos campos (PasarDataSetAPROF03ObjetivoProductoInfo) y terminaba devolviendo NULL en los registros, esto no dejaba la información en la Exportación y por ende en la Importación no subían los Productos. Generación de instaladores. Soporte técnico por correo electrónico, telefónico y en sitio.WiX Toolset: WiX v3.7 RC: WiX v3.7 RC (3.7.1119.0) provides feature complete Bundle update and reference tracking plus several bug fixes. For more information see Rob's blog post about the release: http://robmensching.com/blog/posts/2012/11/20/WiX-v3.7-Release-Candidate-availablePicturethrill: Version 2.11.20.0: Fixed up Bing image provider on Windows 8Excel AddIn to reset the last worksheet cell: XSFormatCleaner.xla: Modified the commandbar code to use CommandBar IDs instead of English names.Json.NET: Json.NET 4.5 Release 11: New feature - Added ITraceWriter, MemoryTraceWriter, DiagnosticsTraceWriter New feature - Added StringEscapeHandling with options to escape HTML and non-ASCII characters New feature - Added non-generic JToken.ToObject methods New feature - Deserialize ISet<T> properties as HashSet<T> New feature - Added implicit conversions for Uri, TimeSpan, Guid New feature - Missing byte, char, Guid, TimeSpan and Uri explicit conversion operators added to JToken New feature - Special case...EntitiesToDTOs - Entity Framework DTO Generator: EntitiesToDTOs.v3.0: DTOs and Assemblers can be generated inside project folders! Choose the types you want to generate! Support for Visual Studio 2012 !!! Support for new Entity Framework EDMX (format used by VS2012) ! Support for Enum Types! Optional automatic check for updates! Added the following methods to Assemblers! IEnumerable<DTO>.ToEntities() : ICollection<Entity> IEnumerable<Entity>.ToDTOs() : ICollection<DTO> Indicate class identifier for DTOs and Assemblers! Cleaner Assemblers code....mojoPortal: 2.3.9.4: see release notes on mojoportal.com http://www.mojoportal.com/mojoportal-2394-released Note that we have separate deployment packages for .NET 3.5 and .NET 4.0, but we recommend you to use .NET 4, we will probably drop support for .NET 3.5 once .NET 4.5 is available The deployment package downloads on this page are pre-compiled and ready for production deployment, they contain no C# source code and are not intended for use in Visual Studio. To download the source code see getting the lates...VidCoder: 1.4.6 Beta: Brought back the x264 advanced options panel due to popular demand. Thank you for all the feedback. x264 Preset/Profile/Tune/Level has been moved back to the Video tab, along with a copy of the "extra options" string. Added Fast Decode and Zero Latency checkboxes to support multiple Tunes. Added cropping option "None". Audio bitrates that are incompatible with the encoder (such as MP3 > 320 kbps) are no longer preset on the list. Fixed crash on opening VidCoder after de-selecting "re...DotNetNuke® Store: 03.01.07: What's New in this release? IMPORTANT: this version requires DotNetNuke 04.06.02 or higher! DO NOT REPORT BUGS HERE IN THE ISSUE TRACKER, INSTEAD USE THE DotNetNuke Store Forum! Bugs corrected: - Replaced some hard coded references to the default address provider classes by the corresponding interfaces to allow the creation of another address provider with a different name. New Features: - Added the 'pickup' delivery option at checkout. - Added the 'no delivery' option in the Store Admin ...Bundle Transformer - a modular extension for ASP.NET Web Optimization Framework: Bundle Transformer 1.6.10: Version: 1.6.10 Published: 11/18/2012 Now almost all of the Bundle Transformer's assemblies is signed (except BundleTransformer.Yui.dll); In BundleTransformer.SassAndScss the SassAndCoffee.Ruby library was replaced by my own implementation of the Sass- and SCSS-compiler (based on code of the SassAndCoffee.Ruby library version 2.0.2.0); In BundleTransformer.CoffeeScript added support of CoffeeScript version 1.4.0-3; In BundleTransformer.TypeScript added support of TypeScript version 0....ExtJS based ASP.NET 2.0 Controls: FineUI v3.2.0: +2012-11-18 v3.2.0 -?????????????????SelectedValueArray????????(◇?◆:)。 -???????????????????RecoverPropertiesFromJObject????(〓?〓、????、??、Vian_Pan)。 -????????????,?????????????,???SelectedValueArray???????(sam.chang)。 -??Alert.Show???????????(swtseaman)。 -???????????????,??Icon??IconUrl????(swtseaman)。 -?????????TimePicker(??)。 -?????????,??/res.axd?css=blue.css&v=1。 -????????,?????????????,???????。 -????MenuCheckBox(???????)。 -?RadioButton??AutoPostBack??。 -???????FCKEditor?????????...BugNET Issue Tracker: BugNET 1.2: Please read our release notes for BugNET 1.2: http://blog.bugnetproject.com/bugnet-1-2-has-been-released Please do not post questions as reviews. Questions should be posted in the Discussions tab, where they will usually get promptly responded to. If you post a question as a review, you will pollute the rating, and you won't get an answer.Paint.NET PSD Plugin: 2.2.0: Changes: Layer group visibility is now applied to all layers within the group. This greatly improves the visual fidelity of complex PSD files that have hidden layer groups. Layer group names are prefixed so that users can get an indication of the layer group hierarchy. (Paint.NET has a flat list of layers, so the hierarchy is flattened out on load.) The progress bar now reports status when saving PSD files, instead of showing an indeterminate rolling bar. Performance improvement of 1...CRM 2011 Visual Ribbon Editor: Visual Ribbon Editor (1.3.1116.7): [IMPROVED] Detailed error message descriptions for FaultException [FIX] Fixed bug in rule CrmOfflineAccessStateRule which had incorrect State attribute name [FIX] Fixed bug in rule EntityPropertyRule which was missing PropertyValue attribute [FIX] Current connection information was not displayed in status bar while refreshing list of entitiesSuper Metroid Randomizer: Super Metroid Randomizer v5: v5 -Added command line functionality for automation purposes. -Implented Krankdud's change to randomize the Etecoon's item. NOTE: this version will not accept seeds from a previous version. The seed format has changed by necessity. v4 -Started putting version numbers at the top of the form. -Added a warning when suitless Maridia is required in a parsed seed. v3 -Changed seed to only generate filename-legal characters. Using old seeds will still work exactly the same. -Files can now be saved...Caliburn Micro: WPF, Silverlight, WP7 and WinRT/Metro made easy.: Caliburn.Micro v1.4: Changes This version includes many bug fixes across all platforms, improvements to nuget support and...the biggest news of all...full support for both WinRT and WP8. Download Contents Debug and Release Assemblies Samples Readme.txt License.txt Packages Available on Nuget Caliburn.Micro – The full framework compiled into an assembly. Caliburn.Micro.Start - Includes Caliburn.Micro plus a starting bootstrapper, view model and view. Caliburn.Micro.Container – The Caliburn.Micro invers...DirectX Tool Kit: November 15, 2012: November 15, 2012 Added support for WIC2 when available on Windows 8 and Windows 7 with KB 2670838 Cleaned up warning level 4 warningsDotNetNuke® Community Edition CMS: 06.02.05: Major Highlights Updated the system so that it supports nested folders in the App_Code folder Updated the Global Error Handling so that when errors within the global.asax handler happen, they are caught and shown in a page displaying the original HTTP error code Fixed issue that stopped users from specifying Link URLs that open on a new window Security FixesFixed issue in the Member Directory module that could show members to non authenticated users Fixed issue in the Lists modul...fastJSON: v2.0.10: - added MonoDroid projectNew Projects1121codeplex01: Today's task is to test portal on JapaneseAgileToDo: a to do list use wpf ef sqlce!Applay: Applay is a library that allows you to wrap authorization and validation around the services of your application layer by using a dynamic proxy.ArunimaErp: Enterprise Resource Planning Software for Arunima GroupBootCMS: BootCMS makes webdevelopment easy.codeplex01: I need go out for a whileCoding4Fun's Maelstrom: Introduced at //build/ 2012, Maelstrom is Coding4Fun's latest creation. Step up to the podium and battle against your opponent in full-on stereoscopic 3D!CTCS Project 2012: 11/21/2012 @ svn repository ctodo: TODO List Management Librarydeploy-with-ease: One-click deployment tool based on DrobBox files hostingDesign Resources .NET: D-R.NET is a set of pre-built implementations of oft-recurring application designs. D-R.NET saves considerable time and money in building user-focused applications: from basic to complex. DnfWeb: dnf??Dr.Peng: dr.peng ????????。DriveKeepAlive: Managed .NET service intended to keep external hard drives "awake" for immediate access. Developed in C# with Visual Studio 2008Ecommerce Platform: Ecommerce PlatformEventManagerReset: Project created for Reset meetings.FaceComparerDistributed: project of face compare distributed versionFileSystemExplorerExample: WPF MVVM Sample applicationFinlogiK ReSharper Contrib: FinlogiK ReSharper Contrib is a plugin for ReSharper 5.1 which adds code cleanup and inspection options for static qualifiers.Gestione Lampade Votive: Gestione dei canoni annuali dei loculi cimiteriali, con stampa di comunicazioni ai contribuenti e dei bollettini di conto corrente postale (a due o tre cedole).GI_PII: HABA BABA?GIV_P2: second projectHex o'clock: Projekt kolorowego zegara.IISProcessScheduler: Schedule processes from within IIS.Image Tagger & Resizer: Resize, and text in the lower right of picture with i.e. copyright information.IT Kohvik: ITK cafe school project.jean1121codeplex01: goodKooboo3 Helper: It's a developer tutorial code for kooboo cms v3. http://kooboo.codeplex.comMAVI: mobile application for the visually impaired: bill recognition & tag and recognize objects based on a specific stickerMecanismos de Segurança Interoperáveis para Serviços Web: Esse projeto pretende desenvolver um framework que forneça requisitos de segurança de forma interoperável através de Serviços Web. Metro UI For Windows Forms: Provides a set of controls and form templates for designing user interfaces based on a similar minimalist metro style. For those who love Windows Forms.NHSmartBootstrapper: In a "fast-changing" world, your LoB application needs to be ready to change as well. The usage of NHibernate Listeners together with smart application bootstrapping, even in a complex scenario, can lead to extensible and new-feature-ready applications. Office Add-In Monitor: Office Add-in Monitor protects add-ins from being disabled.Orchard Responsive Theme Machine: A responsive version of the Orchard CMS "Theme Machine" which is commonly used as a starting point for building custom themes. Supports many resolutions.Orchard Simple Contact Form: An Orchard CMS module that provides a simple contact form that sends an email. It can be used as either a content part or widget.Peon War: Peon war is a game where peons are fighting.Project Files Linker (VS Add-In): PFL project is used to generate multiple projects with links to the same files to achieve projects for different .NET FW versions.Quibbler - Universal News Reader: Quibbler is a product designed and developed by Indigo Architects. Quibbler is a desktop application which runs on user's machine and provides a intuitive user interface for reading news in offline mode. Quibbler is developed in WPF (.Net 3.5).Samcrypt: .SenchaTest: SenchaTestShared Genomics Project - Workbench Codebase: The Shared Genomics workbench enables a diverse user group of researchers to explore the associations between genetic and other factors in their datasets. It provides a graphical user interface to the analysis functions published in a sister Codeplex project i.e. MPI Codebase.SharePoint 2013 FBA Pack: This is the home of the SharePoint 2013 FBA Pack. The FBA Pack for SharePoint 2013 is currently in development and is coming soon.SharePoint Term Store PowerShell Backup & Restore Scripts: This project is focused on development of PowerShell script tools for backup and restore of SharePoint Managed Metadata service application Term Store taxonomy.SharpPlanets: A simple game completely designed and written in C#, inspired by JPlanets.SpaceShooter: A small hobbyist game. It is similar to the 2D Arcade shooter games.Stretched Background Image jQuery plugin: jQuery plugin for adding a stretched background image for any element in a web page. Uses an absolutely positioned image at z-index -1.Stsadm Templates for Visual Studio: The Stsadm Templates for Visual Studio 2005 and 2008 support you in making command extensions for SharePoint's commnand line tool stsadm.exe.SwissPost EasyTrack API: The SwissPost EasyTrack API allows you to track your parcels or letters everytime and in every application.System.Threading.Joins: The Joins project provides asynchronous concurrency semantics based on join calculus and modeled after the Microsoft Research C? (C Omega) project.T nagu Tetris: Meie versioon tuntud mängust tetris.testdd11202012tfs01: juktestddhg11202012hg01: stesttom11202012git02: fdsfdstesttom11202012hg01: gfdTetrissimus: Tetrissimus is an open source "Tetris" alike game totally written in DHTML (JavaScript, CSS and HTML) that uses keyboard. This cross-platform and cross-browser game was tested under BeOS, Linux, NetBSD, OpenBSD, FreeBSD, Windows and others.Thrift Client .NET for WinRT (Windows Store Apps): thrift .net client for WinRT applicationTwitter Bootstrap for SharePoint: A Masterpage for SharePoint 2010 including the twitter bootstrap front-end frameworkTX Spell .NET ActiveX Package: TX Spell .NET ActiveX Package enables you to add high-performance spell checking capabilities to your VB6 applications.USB ACCELEROMETER: This project is a test demo for usb accelerometer. Application plays music (mp3 file) while usb acc gives high values from its coordinate between interval.VfaAccoutApps: Cash Payment Application of Vf AsiaVisualPoint Use PowerPoint inside Visual Studio: VisualPoint lets you show PowerPoint presentations from inside Visual Studio. Future release will automate walkthroughs and presentations.VS2010 Rc1 Fix: Illustrates a fix for working with the ASAP.NET Wizard control with VS2010 RC1WebSite.Request: WebSite.Request launch web request (via XMLHTTP) on website. Use, for example, to make initial request to sharepoint URL and escape "slow first request" problem.WPF Checked ListBox: This is simple implementation of WPF Checked ListBoxWPortal: doing nothing. that's it. i just want to use the subversion management. XNA Capture the Flag for the Microsoft Zune: Capture the Flag is a 2d Capture the flag game made for the Zune platform using XNA 3.0 CTP. Players choose to join or start a network session in the main menu. When in game, the player uses left or right on the DPad to choose the team on which to play with. Once sides have been chosen the party leader presses the center button on the Dpad to start the game. Teams switch between offense and defense for a total of 4 rounds in each game. When the game is over the party leader simply presses th...XPS Indexer: Xps file indexing for Google Desktop

    Read the article

  • CodePlex Daily Summary for Tuesday, November 13, 2012

    CodePlex Daily Summary for Tuesday, November 13, 2012Popular ReleasesSymphony Framework: Symphony Framework v2.0.0.6: Symphony Framework version 2.0.0.6. has just been released General note: If you install Symphony Framework 2.0.0.6 you must re-generate all your code-generated source files, resource files, controls and windows. Failure to regenerate will cause your applications to fail. Symphony Framework requires at least version 4.2.3 of CodeGen due to some new functionality that has been added. Please ensure that you download and install the latest version of CodeGen. You can review the full release ...AcDown?????: AcDown????? v4.3: ??●AcDown??????????、??、??、???????。????,????,?????????????????????????。???????????Acfun、????(Bilibili)、??、??、YouTube、??、???、??????、SF????、????????????。 ●??????AcPlay?????,??????、????????????????。 ● AcDown??????????????????,????????????????????????????。 ● AcDown???????C#??,????.NET Framework 2.0??。?????"Acfun?????"。 ????32??64? Windows XP/Vista/7/8 ???? 32??64? ???Linux ????(1)????????Windows XP???,????????.NET Framework 2.0???(x86),?????"?????????"??? (2)???????????Linux???,????????Mono?? ??2...WallSwitch: WallSwitch 1.2.1: Version 1.2.1 Changes: Improved collage image distribution to overlap older images first. Set default collage background blur distance to 4 (provides a more gradual effect). Fixed issue where wallpaper not displayed on Windows Vista when Cross-Fade transitions enabled. Fixed issue with duplicated themes not updating history view correctly.????: ???? 1.0: ????ALinq Dynamic (Entity SQL for Linq to SQL): ALinq Dynamic v1.1: 1. Fix a few bugs about aggregate function. 2. Supports more functions. 3. Append more samples.Unicode IVS Add-in for Microsoft Office: Unicode IVS Add-in for Microsoft Office: Unicode IVS Add-in for Microsoft Office ??? ?????、Unicode IVS?????????????????Unicode IVS???????????????。??、??????????????、?????????????????????????????。Microsoft Ajax Minifier: Microsoft Ajax Minifier 4.74: fix for issue #18836 - sometimes throws null-reference errors in ActivationObject.AnalyzeScope method. add back the Context object's 8-parameter constructor, since someone has code that's using it. throw a low-pri warning if an expression statement is == or ===; warn that the developer may have meant an assignment (=). if window.XXXX or window"XXXX" is encountered, add XXXX (as long as it's a valid JavaScript identifier) to the known globals so subsequent references to XXXX won't throw ...Home Access Plus+: v8.3: Changes: Fixed: A odd scroll bar showing up for no reason Changed: Added some code to hopefully sort out the details view when there is a small number of files Fixed: Where the details toolbar shows in the wrong place until you scroll Fixed: Where the Help Desk live tile shows all open tiles, instead of user specific tiles (admins still see all) Added: Powerpoint Files Filter Added: Print style for Booking System Added: Silent check for the logon tracker Updated: Logon Tracker I...???????: Monitor 2012-11-11: This is the first releaseVidCoder: 1.4.5 Beta: Removed the old Advanced user interface and moved x264 preset/profile/tune there instead. The functionality is still available through editing the options string. Added ability to specify the H.264 level. Added ability to choose VidCoder's interface language. If you are interested in translating, we can get VidCoder in your language! Updated WPF text rendering to use the better Display mode. Updated HandBrake core to SVN 5045. Removed logic that forced the .m4v extension in certain ...ImageGlass: Version 1.5: http://i1214.photobucket.com/albums/cc483/phapsuxeko/ImageGlass/1.png v1.5.4401.3015 Thumbnail bar: Increase loading speed Thumbnail image with ratio Support personal customization: mouse up, mouse down, mouse hover, selected item... Scroll to show all items Image viewer Zoom by scroll, or selected rectangle Speed up loading Zoom to cursor point New background design and customization and others... v1.5.4430.483 Thumbnail bar: Auto move scroll bar to selected image Show / Hi...Building Windows 8 Apps with C# and XAML: Full Source Chapters 1 - 10 for Windows 8 Fix 002: This is the full source from all chapters of the book, compiled and tested on Windows 8 RTM. Includes: A fix for the Netflix example from Chapter 6 that was missing a service reference A fix for the ImageHelper issue (images were not being saved) - this was due to the buffer being inadequate and required streaming the writeable bitmap to a buffer first before encoding and savingmyCollections: Version 2.3.2.0: New in this version : Added TheGamesDB.net API for Games and NDS Added Support for Windows Media Center Added Support for myMovies Added Support for XBMC Added Support for Dune HD Added Support for Mede8er Added Support for WD HDTV Added Fast search options Added order by Artist/Album for music You can now create covers and background for games You can now update your ID3 tag with the info of myCollections Fixed several provider Performance improvement New Splash ...Draw: Draw 1.0: Drawing PadPlayer Framework by Microsoft: Player Framework for Windows 8 (v1.0): IMPORTANT: List of breaking changes from preview 7 Ability to move control panel or individual elements outside media player. more info... New Entertainment app theme for out of the box support for Windows 8 Entertainment app guidelines. more info... VSIX reference names shortened. Allows seeing plugin name from "Add Reference" dialog without resizing. FreeWheel SmartXML now supports new "Standard" event callback type. Other minor misc fixes and improvements ADDITIONAL DOWNLOADSSmo...WebSearch.Net: WebSearch.Net 3.1: WebSearch.Net is an open-source research platform that provides uniform data source access, data modeling, feature calculation, data mining, etc. It facilitates the experiments of web search researchers due to its high flexibility and extensibility. The platform can be used or extended by any language compatible for .Net 2 framework, from C# (recommended), VB.Net to C++ and Java. Thanks to the large coverage of knowledge in web search research, it is necessary to model the techniques and main...Umbraco CMS: Umbraco 4.10.0: NugetNuGet BlogRead the release blog post for 4.10.0. Whats newMVC support New request pipeline Many, many bugfixes (see the issue tracker for a complete list) Read the documentation for the MVC bits. Breaking changesWe have done all we can not to break backwards compatibility, but we had to do some minor breaking changes: Removed graphicHeadlineFormat config setting from umbracoSettings.config (an old relic from the 3.x days) U4-690 DynamicNode ChildrenAsList was fixed, altering it'...SQL Server Partitioned Table Framework: Partitioned Table Framework Release 1.0: SQL Server 2012 ReleaseSharePoint Manager 2013: SharePoint Manager 2013 Release ver 1.0.12.1106: SharePoint Manager 2013 Release (ver: 1.0.12.1106) is now ready for SharePoint 2013. The new version has an expanded view of the SharePoint object model and has been tested on SharePoint 2013 RTM. As a bonus, the new version is also available for SharePoint 2010 as a separate download.Fiskalizacija za developere: FiskalizacijaDev 1.2: Verzija 1.2. je, prije svega, odgovor na novu verziju Tehnicke specifikacije (v1.1.) koja je objavljena prije nekoliko dana. Pored novosti vezanih uz (sitne) izmjene u spomenutoj novoj verziji Tehnicke dokumentacije, projekt smo prošili sa nekim dodatnim feature-ima od kojih je vecina proizašla iz vaših prijedloga - hvala :) Novosti u v1.2. su: - Neusuglašenost zahtjeva (http://fiskalizacija.codeplex.com/workitem/645) - Sample projekt - iznosi se množe sa 100 (http://fiskalizacija.codeplex.c...New Projects3jidi IPTV App: 3jidi IPTV application on microsoft mediaroomAX 2012 Custom Operating Units: With this tool, non technical users can create custom operating units, link them with existing org model, model custom units as financial dimensions etc.BASE32 Encoder: This awesome app let you convert all your music, pictures and video to brand new BASE32 encoding! BilgeAdam.ChannelShow: BilgeAdam.ChannelShowBlueset Studio Opensource Projects: Only for Opensource projects form Blueset Studio.Bubble Trouble: This is a game where you are trapped in a room with lethal bubbles bouncing around the rooms. You must use your special vine gun to shoot and pop the bubbles!ClomibepASP (Suspended): PL: Zaawansowany system zarzadzania trescia ClomibepASP. EN: Advenced content managment system ClomibepASP.CoBaS - Contract Based Serializer: The serialization framework that cares for bits and speed :)DelegateDuck: New stub library for C#. You can build with it any object using delegates and such an object can be casted to any compatible interface.Demir Yayincilik: Ulusal arastirmacilarin ana dilleri ile yaptiklari yayinlarin kolay dagitilmasi ve izlenmesi gereksiniminden hareketle kurulan Demir yayincilik...DNN LiveEvents: DotNetNuke Live Events ModuleFamFamFam Silk Icons Atlas (CSS Sprites): A CSS/Image generator for CSS Sprites (Atlas) for FamFamFam Silk iconsGuid Finder Solution for Microsoft Dynamics CRM 2011: Guid Finder Solution for Microsoft Dynamics CRM 2011. This Solution helps to find any record "GUID" across all entities in Dynamics CRM. hyd: a game demoJogo do Galo: JOGO DO GALO REGRAS •O tabuleiro é a matriz de três linhas em três colunas. •Dois jogadores escolhem três peças cada um. •Os jogadores jogam alternadamente, uma peça de cada vez, num espaço que esteja vazio. •O objectivo é conseguir três peças iguais em linha, quer horizontal, vjQCalendarPart: jQCalendarPart is a JS application which when added to a CEWP in SP 2010 will display a jQuery Calendar control with the upcoming events from the Calendar list.Kinect Table Tennis: A 2D Top-down Kinect table tennis game! Booyeah!MathNullable: The example of the Nullable Mathematics.Metro Launch: Metro Launch is a new Start menu inspired by Windows 8's.Monoxide.Diagnostics: This is Systems.Diagnostics source code extracted from Mono so that people on any platform (Windows, too!) can extend more of the tracing framework.new1325: hellonew1327: helloPizza-Service: School Project of a Pizza-Service application.ProjectOnElance: SomeProjectOnElanceRemote Controller for Trackmania: Evzrecon is a remote controller for Trackmania Forever dedicated servers, much like XASECO but written in Java.SoftRenderer: a software rendererStripeOne ShortenUrl: Projeto de estudo para encurtar urls, com cms para o usuário (caso seja registrado ou por sessão) e cms administrativo com estatisticas de urls mais usadas.testtom11122012git01: htesttom11122012hg01: fdstesttom11122012tfs01: fdstesttom11122012tfs03: rewThe new Basecamp API C# Wrapper: This project aims to be a complete C# wrapper around the new Basecamp API. Direct API call support in addition to convenience methods are provided.TVendas: Este projeto surgiu com a necessidade de se ter um software de gerenciamento de vendas web e gratuito. Então surgiu o TVendas.WDTVHUBLIVE Companion: Intitial summary : This is a project to learn C# and to create an application to manage media on a WDTVLiveHub. WordTrending: ECE 275 Assignment #4Yet another SharePoint 2010 Deployment Script: The following PowerShell script is intended to help operations staff as well as developers to automate the base installation of SharePoint 2010 Server. Zytonic Hotkeys: Zytonic Hotkeys Is a User Library That Aims to defeat The hassle of creating User Hotkeys for your .NET Applications.????: ????

    Read the article

  • Ubuntu 11.04 and 10.04 hang with black screen while installing from USB disk

    - by Bill
    I've been trying to install Ubuntu 11.04 from a USB flash stick and each time I try to boot from the USB key one of two things happen: A) The screen that asks you what you would like to do (e.g. run Ubuntu from the USB key or install it) shows up and the countdown to the default option starts to count down but as soon as I either touch the keyboard (sometimes I press enter or the arrow keys to select an option) or the countdown gets to zero the screen just locks up and nothing happens no matter how long I wait. B) When I boot from the USB key the screen will flicker for a second and then go black with a flashing white underscore at the top left corner of the screen. Again it doesn't matter how long I wait, nothing happens and pressing keys doesn't do a thing. The very first time I tried to install it I got a terminal-like screen that said something about a directory called 'casper' having an error of some sort. I have tried installing from USB using both 11.04 and 10.10. I'm about to try 10.04. I have read tons of forum posts about this but so far I haven't seen anything in the solutions that apply to me. My intention is to dual boot Windows 7 and Ubuntu. I must keep Windows as I am required to use Visual Studio for one of my college courses. Right now I'm using Wubi but I really want a full install. I can't use LVPM because it doesn't work with the version of Wubi I used. So now I'm thinking my best bet is to try to get a clean install working. I'd also convert Wubi to a full install too but there's no solution as far as I've read. So could someone tell me a reason why this is happening or if there's something I can do to get around the problem? I'm using a Gateway LT2802u netbook with and Intel Atom N455 processor, 1GB RAM, Intel Graphics Media Accelerator 3150 graphics card, and a 250GB HDD. I don't have anything on my current Wubi install that I can't replace so keep in mind when answering that I don't care if I lose my current settings and files from Wubi. Thanks everyone! UPDATE I just answered my own question so in case anyone else is having this same problem using similar hardware, do the following: When I first tried installing 11.04 I used the recommended universal installer tool to create the USB live/installation disk. That caused the original problem. Note that I had already downloaded the 11.04 ISO and did not use the included downloader from the USB creator. After that failed I used the same USB creator but had it download 10.10 for me. It also failed with the same issue. I repeated this process with unetbootin as well for both versions. Finally, I downloaded the Ubuntu 10.04 ISO and used the recommended USB creator once again. There was an error while creating the USB live install so I reformatted the USB key as FAT32 and tried again. It created the USB key. I then booted from the USB flash drive and selected "Install Ubuntu" (exact wording was different). It worked! It took me through the process that you see shown in pictures on the Ubuntu website. I let it create the appropriate partitions for me and it simply worked. I did get a few errors while the system tried to restart after it installed. It hung on a terminal-like screen but I pressed ENTER and it restarted. I booted into Windows 7, it checked the disks as it sensed that I messed with a partition, then it booted into Windows normally. Now I'm going to uninstall Wubi and update my new full install of Ubuntu! I'm excited to get the benefits of a full install now. So in the end, hopefully someone can learn from what I did.

    Read the article

  • CodePlex Daily Summary for Monday, November 14, 2011

    CodePlex Daily Summary for Monday, November 14, 2011Popular ReleasesWeapsy: 0.4.1 Alpha: Edit Text bug fixedDesktop Google Reader: 1.4.2: This release remove the like and the broadcast buttons as Google Reader stopped supporting them (no, we don't like this decission...) Additionally and to have at least a small plus: the login window now automaitcally logs you in if you stored username and passwort (no more extra click needed) Finally added WebKit .NET to the about window and removed AwesomiumZombsquare: Solución inicial: Código fuente de la solución. Versión 7099 Tambien puedes descargar de aquí los snippets de código que utilizamos en la demostración.RDRemote: Remote Desktop remote configurator V 1.0.0: Remote Desktop remote configurator V 1.0.0SQL Monitor - tracking sql server activities: SQLMon 4.1 alpha1: 1. improved version compare, now support comparing two text files. right click on object script text box and choose "Compare" or create new query window and right click and choose "Compare" 2. improved version compare, now automatically sync two text boxes. 3. fixed problem with activities (process/job) when refreshing while current activities have less count than previous one. 4. better start up by automatically shows create connection window when there is no connection defined.Rawr: Rawr 4.2.7: This is the Downloadable WPF version of Rawr!For web-based version see http://elitistjerks.com/rawr.php You can find the version notes at: http://rawr.codeplex.com/wikipage?title=VersionNotes Rawr AddonWe now have a Rawr Official Addon for in-game exporting and importing of character data hosted on Curse. The Addon does not perform calculations like Rawr, it simply shows your exported Rawr data in wow tooltips and lets you export your character to Rawr (including bag and bank items) like Char...VidCoder: 1.2.2: Updated Handbrake core to svn 4344. Fixed the 6-channel discrete mixdown option not appearing for AAC encoders. Added handling for possible exceptions when copying to the clipboard, added retries and message when it fails. Fixed issue with audio bitrate UI not appearing sometimes when switching audio encoders. Added extra checks to protect against reported crashes. Added code to upgrade encoding profiles on old queued items.Dynamic PagedCollection (Silverlight / WPF Pagination): PagedCollection: All classes which facilitate your dynamic pagination in Silverlight or WPF !Media Companion: MC 3.422b Weekly: Ensure .NET 4.0 Full Framework is installed. (Available from http://www.microsoft.com/download/en/details.aspx?id=17718) Ensure the NFO ID fix is applied when transitioning from versions prior to 3.416b. (Details here) TV Show Resolutions... Made the TV Shows folder list sorted. Re-visibled 'Manually Add Path' in Root Folders. Sorted list to process during new tv episode search Rebuild Movies now processes thru folders alphabetically Fix for issue #208 - Display Missing Episodes is not popu...DotSpatial: DotSpatial Release Candidate 1 (1.0.823): Supports loading extensions using System.ComponentModel.Composition. DemoMap compiled as x86 so that GDAL runs on x64 machines. How to: Use an Assembly from the WebBe aware that your browser may add an identifier to downloaded files which results in "blocked" dll files. You can follow the following link to learn how to "Unblock" files. Right click on the zip file before unzipping, choose properties, go to the general tab and click the unblock button. http://msdn.microsoft.com/en-us/library...XPath Visualizer: XPathVisualizer v1.3 Latest: This is v1.3.0.6 of XpathVisualizer. This is an update release for v1.3. These workitems have been fixed since v1.3.0.5: 7429 7432 7427MSBuild Extension Pack: November 2011: Release Blog Post The MSBuild Extension Pack November 2011 release provides a collection of over 415 MSBuild tasks. A high level summary of what the tasks currently cover includes the following: System Items: Active Directory, Certificates, COM+, Console, Date and Time, Drives, Environment Variables, Event Logs, Files and Folders, FTP, GAC, Network, Performance Counters, Registry, Services, Sound Code: Assemblies, AsyncExec, CAB Files, Code Signing, DynamicExecute, File Detokenisation, GU...CODE Framework: 4.0.11110.0: Various minor fixes and tweaks.Extensions for Reactive Extensions (Rxx): Rxx 1.2: What's NewRelated Work Items Please read the latest release notes for details about what's new. Content SummaryRxx provides the following features. See the Documentation for details. Many IObservable<T> extension methods and IEnumerable<T> extension methods. Many useful types such as ViewModel, CommandSubject, ListSubject, DictionarySubject, ObservableDynamicObject, Either<TLeft, TRight>, Maybe<T> and others. Various interactive labs that illustrate the runtime behavior of the extensio...Player Framework by Microsoft: HTML5 Player Framework 1.0: Additional DownloadsHTML5 Player Framework Examples - This is a set of examples showing how to setup and initialize the HTML5 Player Framework. This includes examples of how to use the Player Framework with both the HTML5 video tag and Silverlight player. Note: Be sure to unblock the zip file before using. Note: In order to test Silverlight fallback in the included sample app, you need to run the html and xap files over http (e.g. over localhost). Silverlight Players - Visit the Silverlig...MapWindow 4: MapWindow GIS v4.8.6 - Final release - 64Bit: What’s New in 4.8.6 (Final release)A few minor issues have been fixed What’s New in 4.8.5 (Beta release)Assign projection tool. (Sergei Leschinsky) Projection dialects. (Sergei Leschinsky) Projections database converted to SQLite format. (Sergei Leschinsky) Basic code for database support - will be developed further (ShapefileDataClient class, IDataProvider interface). (Sergei Leschinsky) 'Export shapefile to database' tool. (Sergei Leschinsky) Made the GEOS library static. geos.dl...Facebook C# SDK: v5.3.2: This is a RTW release which adds new features and bug fixes to v5.2.1. Query/QueryAsync methods uses graph api instead of legacy rest api. removed dependency from Code Contracts enabled Task Parallel Support in .NET 4.0+ (experimental) added support for early preview for .NET 4.5 (binaries not distributed in codeplex nor nuget.org, will need to manually build from Facebook-Net45.sln) added additional method overloads for .NET 4.5 to support IProgress<T> for upload progress added ne...Delete Inactive TS Ports: List and delete the Inactive TS Ports: UPDATEAdded support for windows 2003 servers and removed some null reference errors when the registry key was not present List and delete the Inactive TS Ports - The InactiveTSPortList.EXE accepts command line arguments The InactiveTSPortList.Standalone.WithoutPrompt.exe runs as a standalone exe without the need for any command line arguments.ClosedXML - The easy way to OpenXML: ClosedXML 0.60.0: Added almost full support for auto filters (missing custom date filters). See examples Filter Values, Custom Filters Fixed issues 7016, 7391, 7388, 7389, 7198, 7196, 7194, 7186, 7067, 7115, 7144Microsoft Research Boogie: Nightly builds: This download category contains automatically released nightly builds, reflecting the current state of Boogie's development. We try to make sure each nightly build passes the test suite. If you suspect that was not the case, please try the previous nightly build to see if that really is the problem. Also, please see the installation instructions.New ProjectsAwpAdmin: AwpAdmin (name tentative) is a powerful BF3 admin tool. This admin tool is being designed to be easy to setup and maintain while having a great deal of customizability and power. This is written in C# and is being designed to be Mono-compatible.ChainReaction.Net: Extension library that aims to allow method chains to be attached to code statements, allowing them to be read more fluently , allowing extra logic to effectively be bolted on in a fluid wayCodeigniter SQL Azure/SQL Server Unicode supported driver.: Codeigniter?SQL Server 2005/2008 SQLAzure????????????。 NPrefix???????、Unicode???(??????)?????????????。 Active record / ???????????、N?????????????????????????。 ???????????????、N???????????????????、?????????N???????????????????。 ????????????????。 See http://msdn.microsoft.com/ja-jp/library/ms191313.aspx ??、????????????????????。 (Codeplex?Apache????????????、Ellislab license????????。) --- SQL Server 2005 / 2008 / SQL Azure driver class for Codeigniter. this driver N prefix uni...EZ-NFC: EZ-NFC is a .NET library, written in C#, aimed at simplifying the use of NFC in applications.Farigola: A library to organize and manage dynamic data. It's developed in C#/.NET language. Forca_adrikei: Forca implementada para o curso de C# da ufscar sorocaba.GemTD: Gem Tower Defense starcraft 2 map simulator implemented via C# and XNA. Components needed: Microsoft .NET Framework 4 Microsoft XNAGSISWebServiceMVC: This is a sample of an MVC application using the Greek GSIS Web Service at http://www.gsis.gr/wsnp.html (in Greek).Ini4Net: Ini4Net is a simple INI class for parsing INI files in your application. There are many INI solutions available around but non of them met my simplicity so I rolled-my-own. I have been using this since 2008 in several applications that are being used in the enterprise.Jogo da Memória: Projeto de C# - Jogo da memóriaJson DataContract Builder - Create JsonAPI SDK from samples & xmls: Yeah, you can access json with dynamic & Json.Net. But why can't we have the old static way? Is there no one miss the happiness of working with intellisense? There must be a easy way.K-Vizinhos: K-VizinhosLie to Me Windows Phone 7 App: Lie to me - application on WindowsPhone7 platform for testing face expressions, basend on popular serial "Lie To Me".Localization Project: Localization project is C# library to simplify localizing .NET applications and websites. Primary purpose of this project is support instant language switching on the fly.Luminji.wp: luminji's melearning windows phone soft.mergemania - pdf merging .net library based on iTextSharp: Merge PDF documents from different source documents into several destination documents. Set the page ranges to merge from and the page ranges to merge into. Everything is configured via an single XML file. You access all elements through strongly typed classes generated from XSD.Metro Pandora: Metro Pandora aims to ship a Pandora SDK and apps for XAML .net platforms.MiniState: MiniState is an attempt to provide simple abstraction layer to reading and writing state information like HTTP cookies to minimise cookie size and increase the quality of code and security.Mocklet: Mocklet is a suite of PowerShell cmdlets designed to help system administrator generate sample or mock data for testing or building test environments.nethelper: silverlight extend libraryNeverForget: NeverForget is a simple KB projectOpenCV examples: Sample project for interprocess image sharing. Using OpenCV and Boost. Server : Capture image from webcam and write image to shared memory region. Client : Read image from shared memory and imshow the image.Portable Class Libraries Contrib: Portable Class Libraries Contrib provides portable adapters and APIs that help bridge the gap between different platforms when using the new Portable Class Library feature. This makes it easier to convert existing platform-specific libraries over to use portable APIs.sbfa: sbfaShortcut Manager: Shortcut Manager (SM) is solution for everyone who is looking for creating keyboard shortcuts in .NET Winforms applications. SM uses Win32 API to create keyboard hook and fires supplied handler after required shortcut is pressed.SIGEMdispro: Proyecto de un curso de la universidadSimpleMvcCaptcha: Captcha HtmlHelper for ASP.NET MVC 3 with simple ariphmetic expression. No WCF required, neither any other communications. Written in C#.Traveling salesman problem solver using google maps: This application provides a solution for the traveling salesman problem using Google maps, developed in C# and ASP.net.WebPALTT: A Web performance and load test tool for testing web sites / applications. Features include easy to use scenario builder and powerful scripting for high customisability. Developed in .Net C#.WriteMyName: Código para escrever o nome do autor no começo de código fonte.zenSQLcompare: Compare SQL

    Read the article

  • CodePlex Daily Summary for Friday, November 26, 2010

    CodePlex Daily Summary for Friday, November 26, 2010Popular ReleasesMath.NET Numerics: Beta 1: First beta of Math.NET Numerics. Only contains the managed linear algebra provider. Beta 2 will include the native linear algebra providers along with better documentation and examples.WatchersNET.SiteMap: WatchersNET.SiteMap 01.03.02: Whats NewNew Tax Filter, You can now select which Terms you want to Use.TextGen - Another Template Based Text Generator: TextGen v0.2: This is the first version of TextGen exposing its core functionality to COM. See the Access demo (Access 2000 file format) included in the package. For installation and usage instructions see ReadMe.txt. Have fun and provide feedback!Minecraft GPS: Minecraft GPS 1.1: 1.1 Release New Features Compass! New style. Set opacity on main window to allow overlay of Minecraft.Microsoft All-In-One Code Framework: Visual Studio 2010 Code Samples 2010-11-25: Code samples for Visual Studio 2010Typps (formerly jiffycms) wysiwyg rich text HTML editor for ASP.NET AJAX: Typps 2.9: -When uploading files (not images), through the file uploader and the multi-file uploader, FileUploaded and MultiFileUploaded event handlers were reporting an empty event argument, this is fixed now. -Fixed also url field not updating when uploading a file ( not image)Wii Backup Fusion: Wii Backup Fusion 0.8.5 Beta: - WBFS repair (default) options fixed - Transfer to image fixed - Settings ui widget names fixed - Some little bug fixes You need to reset the settings! Delete WiiBaFu's config file or registry entries on windows: Linux: ~/.config/WiiBaFu/wiibafu.conf Windows: HKEY_CURRENT_USER\Software\WiiBaFu\wiibafu Mac OS X: ~/Library/Preferences/com.wiibafu.wiibafu.plist Caution: This is a BETA version! Errors, crashes and data loss not impossible! Use in test environments only, not on productive syste...Minemapper: Minemapper v0.1.3: Added process count and world size calculation progress to the status bar. Added View->'Status Bar' menu item to show/hide the status bar. Status bar is automatically shown when loading a world. Added a prompt, when loading a world, to use or clear cached images.SQL Monitor: SQL Monitor 1.4: 1.added automatically load sql server instances 2.added friendly wait cursor 3.fixed problem with 4.0 fx 4.added exception handlingLateBindingApi.Excel: LateBindingApi.Excel Release 0.7f (fixed): Unterschiede zur Vorgängerversion: - XlConverter.ToRgb umbenannt zu XlConverter.ToDouble - XlConverter.GetFileExtension hinzugefügt (.xls oder .xlsx) - Insert Methoden+Overloads für Range und ShapeNodes - Xml Doku im Code entfernt Release+Samples V0.7f: - Enthält Laufzeit DLL und Beispielprojekte Beispielprojekte: COMAddinExample - Demonstriert ein versionslos angebundenes COMAddin Example01 - Background Colors und Borders für Cells Example02 - Font Attributes undAlignment für Cells Examp...Deep Zoom for WPF: First Release: This first release of the Deep Zoom control has the same source code, binaries and demos as the CodeProject article (http://www.codeproject.com/KB/WPF/DeepZoom.aspx).BlogEngine.NET: BlogEngine.NET 2.0 RC: This is a Release Candidate version for BlogEngine.NET 2.0. The most current, stable version of BlogEngine.NET is version 1.6. Find out more about the BlogEngine.NET 2.0 RC here. If you want to extend or modify BlogEngine.NET, you should download the source code. To get started, be sure to check out our installation documentation and the installation screencast. If you are upgrading from a previous version, please take a look at the Upgrading to BlogEngine.NET 2.0 instructions. As this ...NodeXL: Network Overview, Discovery and Exploration for Excel: NodeXL Excel Template, version 1.0.1.156: The NodeXL Excel template displays a network graph using edge and vertex lists stored in an Excel 2007 or Excel 2010 workbook. What's NewThis release adds a feature for aggregating the overall metrics in a folder full of NodeXL workbooks, adds geographical coordinates to the Twitter import features, and fixes a memory-related bug. See the Complete NodeXL Release History for details. Please Note: There is a new option in the setup program to install for "Just Me" or "Everyone." Most people...VFPX: FoxBarcode v.0.11: FoxBarcode v.0.11 - Released 2010.11.22 FoxBarcode is a 100% Visual FoxPro class that provides a tool for generating images with different bar code symbologies to be used in VFP forms and reports, or exported to other applications. Its use and distribution is free for all Visual FoxPro Community. Whats is new? Added a third parameter to the BarcodeImage() method Fixed some minor bugs History FoxBarcode v.0.10 - Released 2010.11.19 - 85 Downloads Project page: FoxBarcodeDotNetAge -a lightweight Mvc jQuery CMS: DotNetAge 1.1.0.5: What is new in DotNetAge 1.1.0.5 ?Document Library features and template added. Resolve issues of templates Improving publishing service performance Opml support added. What is new in DotNetAge 1.1 ? D.N.A Core updatesImprove runtime performance , more stabilize. The DNA core objects model added. Personalization features added that allows users create the personal website, manage their resources, store personal data DynamicUIFixed the PageManager could not move page node bug. ...ASP.NET MVC Project Awesome (jQuery Ajax helpers): 1.3.1 and demos: A rich set of helpers (controls) that you can use to build highly responsive and interactive Ajax-enabled Web applications. These helpers include Autocomplete, AjaxDropdown, Lookup, Confirm Dialog, Popup Form and Pager tested on mozilla, safari, chrome, opera, ie 9b/8/7/6MDownloader: MDownloader-0.15.24.6966: Fixed Updater; Fixed minor bugs;WPF Application Framework (WAF): WPF Application Framework (WAF) 2.0.0.1: Version: 2.0.0.1 (Milestone 1): This release contains the source code of the WPF Application Framework (WAF) and the sample applications. Requirements .NET Framework 4.0 (The package contains a solution file for Visual Studio 2010) The unit test projects require Visual Studio 2010 Professional Remark The sample applications are using Microsoft’s IoC container MEF. However, the WPF Application Framework (WAF) doesn’t force you to use the same IoC container in your application. You can use ....NET Extensions - Extension Methods Library for C# and VB.NET: Release 2011.01: Added new extensions for - object.CountLoopsToNull Added new extensions for DateTime: - DateTime.IsWeekend - DateTime.AddWeeks Added new extensions for string: - string.Repeat - string.IsNumeric - string.ExtractDigits - string.ConcatWith - string.ToGuid - string.ToGuidSave Added new extensions for Exception: - Exception.GetOriginalException Added new extensions for Stream: - Stream.Write (overload) And other new methods ... Release as of dotnetpro 01/2011Free language translator and file converter: Free Language Translator 2.2: Starting with version 2.0, the translator encountered a major redesign that uses MEF based plugins and .net 4.0. I've also fixed some bugs and added support for translating subtitles that can show up in video media players. Version 2.1 shows the context menu 'Translate' in Windows Explorer on right click. Version 2.2 has links to start the media file with its associated subtitle. Download the zip file and expand it in a temporary location on your local disk. At a minimum , you should uninstal...New Projects.NET DroneController: The .NET DroneController makes it easy to write applications that allow you to control an ARDrone quadricopter. BELT (A PowerShell Snapin for IE Browser Automation): BELT is a PowerShell snapin for IE browser automation. BELT makes it easier to control IE by PowerShell. "BELT" originally stands for "Browser Element Locating Tool".BusStationInfo: BusStationInfoDadaist: Dadaist is a random natural language generator that allows creation of random yet understandable (and often crazy) placeholder text for web designers. It could one day replace "Lorem ipsum" altogether! It is developed in C# and is a console application.Darskade LMS: Darskade is a kind of Learning Management System (LMS as a branch of CMS) and its main goal is to help professors and teacher assistants to manage classes, communicate with students, upload course contents ,put assignments and grades on it and more.ESRI for TableTops: An extension of the ESRI Api for use on digital tabletops and multitouch surfaces.Execute a SQL Server Agent Job - SSIS Package: The focus of SSMSAGENTJOBVBS is to explain how you can execute a SQL Server Agent Job remotely with the SSIS package, or DTSX file, as a job step. Look at the source code and dissect. Format.NET: Format.NET is an easy to use library to enable advanced and smart object formatting in .NET projects. Extends the default String.Format(...) allowing property resolution, custom formatting and text alignment.Gallery.net: Gallery.net is a tag-based image management solution, initially targeting for High Schools to manage and organize their large digital image assets. It is developed in C#, ASP.Net MVC3. GroupChallenge: GroupChallenge is a trivia game for one or more simultaneous players to interactively answer questions and submit questions to a hosted game server. Source code includes a WCF Data Service (OData) server, Windows Phone client, and a Silverlight client. Great for User Groups.GSWork: Manage clients and events in your company in a fast and efficient, without relying on a physical file. Ideal for companies with workers with no need to be in the same place.hermesystest1: ????? test ???.HTC Sense Util: Windows Mobile application for managing HTC Sense Tabs. The application will control sense and manage the tab control file.IdentityChecker: IdentityCheckerIndexed Material Splatting for Terrain Rendering Demo: This project is a demo using Indexed Material Splatting technique for terrain renderingIntegra: PFCKinet SDK: Kinect SDKLyra 3: Lyra is a small Windows Application to create and manage song-books. Each song-book may contain an arbitrary number of songs which can be created or edited within Lyra and projected using any screen device (e.g. a beamer). Support for full text search and presentation templates.NETWorking: NETWorking allows developers to easily integrate Internet connectivity into their applications. Be it a fault-tolerant distributed cluster or a peer-to-peer system, NETWorking exposes high-performance classes to facilitate application needs in a concise and understandable manner.RAD Platform: Rapid Application Development (RAD) Platform is a free run time report/form/chart designer and generator engine and multi-platform web/windows application servers. New generation of database independent .Net software framework. Design once, run at once on web and windows. Enjoy!Razor Repository Engine: <project name>RazorRepository</project> <programming language>C#</programming language> <activity>Finished</activity>Scientific Calculator: HTML 5 and CSS 3: Online SCIENTIFIC CALCULATOR implements latest features, available in HTML 5, CSS 3 and jQuery. Developed as Rich Internet Application (RIA) w/extremely small footprint (<20kb), it demonstrates best scripting techniques and coding practices; does not require any image files.Seguimiento Facon: Control de seguimiento faconSharePoint Social: Have you ever needed to show the facebook, twitter updates of your organization on your sharepoint portal ? If yes, this project is for you. Simple auto update tool: Makes a easy way to auto update your client software.SteelBattalion.NET: .NET-based library for interfacing with the original Steel Battalion X-Box controller. Utilizes LibUSB drivers. Works on 32-bit and 64-bit platforms, including Windows 7.SystemTimeFreezer: Freezes system datetime to some value you've selectedTeam Explorer Remover: Utility to completely remove TFS Team Explorer from VS.NET 2010. * Removes all registry entries regarding Team Explorer. * Removes all files related to Team Explorer. * Removes all VS.NET commands, menu items and hyperlinks related to Team Explorer (incl. one on StartUp page)TIMESHARE-SELLERS: TIMESHARE-SELLERSVsi Builder 2010: Vsi Builder is an extension for Visual Studio 2010 which allows packaging code snippets and old-style add-ins into .Vsi redistributable packagesWCF Peer Resolver: WCF Peer Resolver is an very extendable and simplified resolver framework to use instead of the built in CurstomPeerResolver in .Net Framework. It is completely developed in C# with .Net Framework 3.5.wsPDV2010: Primeiro desenvolvimento experimental de PDV.

    Read the article

  • How can I recover an ext4 filesystem corrupted after a fsck?

    - by Regan
    I have an ext4 filesystem on luks over software raid5. The filesystem was operating "just fine" for several years when I was beginning to run out of space. I had a 9T volume on 6x2T drives. I began upgrading to 3T drives by doing the mdadm fail, remove, add, rebuild, repeat process until I had a larger array. I then grew the luks container, and then when I unmounted and tried to resize2fs I was given the message the filesystem was dirty and needed e2fsck. Without thinking I just did e2fsck -y /dev/mapper/candybox and it began spewing all kinds of inode being removed type messages (can't remember exactly) I killed e2fsck and tried to remount the filesystem to backup data I was concerned about. When trying to mount at this point I get: # mount /dev/mapper/candybox /candybox mount: wrong fs type, bad option, bad superblock on /dev/mapper/candybox, missing codepage or helper program, or other error In some cases useful info is found in syslog - try dmesg | tail or so Looking back at my older logs I noticed the filesystem was giving this error each time the machine booted: kernel: [79137.275531] EXT4-fs (dm-2): warning: mounting fs with errors, running e2fsck is recommended So shame on me for not paying attention :( I then tried to mount using every backup superblock (one after another) and each attempt left this in my log: EXT4-fs (dm-2): ext4_check_descriptors: Checksum for group 0 failed (26534!=65440) EXT4-fs (dm-2): ext4_check_descriptors: Checksum for group 1 failed (38021!=36729) EXT4-fs (dm-2): ext4_check_descriptors: Checksum for group 2 failed (18336!=39845) ... EXT4-fs (dm-2): ext4_check_descriptors: Checksum for group 11911 failed (28743!=44098) BUG: soft lockup - CPU#0 stuck for 23s! [mount:2939] Attempts to restart e2fsck results in: # e2fsck /dev/mapper/candybox e2fsck 1.41.14 (22-Dec-2010) e2fsck: Group descriptors look bad... trying backup blocks... candy: recovering journal e2fsck: unable to set superblock flags on candy At this point, I decided it best to order some more drives and make an image using ddrescue Now two weeks later I have an image of the luks partition in a .img file. # ls -lh total 14T -rw-r--r-- 1 root root 14T Oct 25 01:57 candybox.img -rw-r--r-- 1 root root 271 Oct 20 14:32 candybox.logfile After numerous attempts using everything I could find online I could not coerce e2fsck to do anything on the image, so I used mkfs.ext4 -L candy candybox.img -m 0 -S and I was able to mount the dirty filesystem readonly without the journal and recover 960G of data. It gave all kinds of errors of various directories not existing and so forth but I was able to get some stuff. Which gave me some hope! I then ran e2fsck again and it had to recreate the root inode and gave a massive list of correcting group counts, I accepted the root inode creation and said no to everything else, leaving a completely empty filesystem. Re-ran again and said yes to all questions with the same result but now a "clean" but empty filesystem. extundelete gives me 0 recoverable inodes found. And now I'm stuck again, I can't come up with any other methods other than dropping to something like photorec which will give me an absolute mess with how large the filesystem was. I'm willing to re-copy the image from the original array and start over, if I can get any suggestions or ideas on a way to get more of my files back. I wish I could give more detailed logs of the commands that have run, but the output is long scrolled passed except for what gets logged to syslog and my memory is not as detailed due to the timeframe this has occurred over. Any help is greatly appreciated!

    Read the article

  • Uncompress GZIPed HTTP Response in Java

    - by bill0ute
    Hi, I'm trying to uncompress a GZIPed HTTP Response by using GZIPInputStream. However I always have the same exception when I try to read the stream : java.util.zip.ZipException: invalid bit length repeat My HTTP Request Header: GET www.myurl.com HTTP/1.0\r\n User-Agent: Mozilla/5.0 (Windows; U; Windows NT 6.1; fr; rv:1.9.2) Gecko/20100115 Firefox/3.6\r\n Accept: text/html,application/xhtml+xml,application/xml;q=0.9,*/*;q=0.8\r\n Accept-Language: fr,fr-fr;q=0.8,en-us;q=0.5,en;q=0.3\r\n Accept-Encoding: gzip,deflate\r\n Accept-Charset: ISO-8859-1,UTF-8;q=0.7,*;q=0.7\r\n Keep-Alive: 115\r\n Connection: keep-alive\r\n X-Requested-With: XMLHttpRequest\r\n Cookie: Some Cookies\r\n\r\n At the end of the HTTP Response header, I get path=/Content-Encoding: gzip, followed by the gziped response. I tried 2 similars codes to uncompress : GZIPInputStream gzip = new GZIPInputStream (new ByteArrayInputStream (tBytes)); StringBuffer szBuffer = new StringBuffer (); byte tByte [] = new byte [1024]; while (true) { int iLength = gzip.read (tByte, 0, 1024); // <-- Error comes here if (iLength < 0) break; szBuffer.append (new String (tByte, 0, iLength)); } And this one that I get on this forum : InputStream gzipStream = new GZIPInputStream (new ByteArrayInputStream (tBytes)); Reader decoder = new InputStreamReader (gzipStream, "UTF-8");//<- I tried ISO-8859-1 and get the same exception BufferedReader buffered = new BufferedReader (decoder); I guess this is an encoding error. Best regards, bill0ute

    Read the article

  • empty response body in ajax (or 206 Partial Content)

    - by Nikita Rybak
    Hi guys, I'm feeling completely stupid because I've spent two hours solving task which should be very simple and which I solved many times before. But now I'm not even sure in which direction to dig. I fail to fetch static content using ajax from local servers (Apache and Mongrel). I get responses 200 and 206 (depending on the server), empty response text (although Content-Length header is always correct), firebug shows request in red. Javascript is very generic, I'm getting same results even here: http://www.w3schools.com/ajax/tryit.asp?filename=tryajax_first (just change document location to 'http://localhost:3000/whatever') So, it's probably not the cause. Well, now I'm out of ideas. I can also post http headers, if it'll help. Thanks! Response Headers Connection close Date Sat, 01 May 2010 21:05:23 GMT Last-Modified Sun, 18 Apr 2010 19:33:26 GMT Content-Type text/html Content-Length 7466 Request Headers Host localhost:3000 User-Agent Mozilla/5.0 (Macintosh; U; Intel Mac OS X 10.6; en-US; rv:1.9.2.3) Gecko/20100401 Firefox/3.6.3 Accept text/html,application/xhtml+xml,application/xml;q=0.9,*/*;q=0.8 Accept-Language en-us,en;q=0.5 Accept-Encoding gzip,deflate Accept-Charset ISO-8859-1,utf-8;q=0.7,*;q=0.7 Keep-Alive 115 Connection keep-alive Referer http://www.w3schools.com/ajax/tryit_view.asp Origin http://www.w3schools.com Response Headers Date Sat, 01 May 2010 21:54:59 GMT Server Apache/2.2.14 (Unix) mod_ssl/2.2.14 OpenSSL/0.9.8l DAV/2 mod_jk/1.2.28 Etag "3d5cbdb-fb4-4819c460d4a40" Accept-Ranges bytes Content-Length 4020 Cache-Control max-age=7200, public, proxy-revalidate Expires Sat, 01 May 2010 23:54:59 GMT Content-Range bytes 0-4019/4020 Keep-Alive timeout=5, max=100 Connection Keep-Alive Content-Type application/javascript Request Headers Host localhost User-Agent Mozilla/5.0 (Macintosh; U; Intel Mac OS X 10.6; en-US; rv:1.9.2.3) Gecko/20100401 Firefox/3.6.3 Accept text/html,application/xhtml+xml,application/xml;q=0.9,*/*;q=0.8 Accept-Language en-us,en;q=0.5 Accept-Encoding gzip,deflate Accept-Charset ISO-8859-1,utf-8;q=0.7,*;q=0.7 Keep-Alive 115 Connection keep-alive Origin null

    Read the article

  • jQuery AJAX Character Encoding Problem

    - by Salty
    Hi everyone, I'm currently coding a French website. There's a schedule page, where a link on the side can be used to load another day's schedule. http://aquate.us/film/horaire.html (At the moment, only the links for November 13th and November 14th work) Here's the JS I'm using to do this: <script type="text/javascript"> function load(y) { $.get(y,function(d) { $("#replace").html(d); mod(); }); } function mod() { $("#dates a").click(function() { y = $(this).attr("href"); load(y); return false; }); } mod(); </script> The actual AJAX works like a charm. My problem lies with the response to the request. Because it is a French website, there are many accented letters. I'm using the ISO-8859-15 charset for that very reason. However, in the response to my AJAX request, the accents are becoming ?'s because the character encoding seems to be changed back to UTF-8. How do I avoid this? I've already tried adding some PHP at the top of the requested documents to set the character set: <?php header('Content-Type: text/html; charset=ISO-8859-15'); ?> But that doesn't seem to work either. Any thoughts? Also, while any of you are looking here...why does the rightmost column seem to become smaller when a new page is loaded, causing the table to distort and each <li> within the <td> to wrap to the next line? Cheers

    Read the article

  • Forms authentication, ASP.NET MVC and WCF RESTful service

    - by J F
    One test webserver, with the following applications service.ganymedes.com:8008 - WCF RESTful service, basically the FormsAuth sample from WCF Starter Kit Preview 2 mvc.ganymedes.com:8008 - ASP.NET MVC 2.0 application web.config for service.ganymedes.com: <authentication mode="Forms"> <forms loginUrl="~/login.aspx" timeout="2880" domain="ganymedes.com" name="GANYMEDES_COOKIE" path="/" /> </authentication> web.config for mvc.ganymedes.com: <authentication mode="Forms"> <forms loginUrl="~/Account/LogOn" timeout="2880" domain="ganymedes.com" name="GANYMEDES_COOKIE" path="/" /> </authentication> Trying my darndest, a GET (or POST for that matter) via jQuery's $.ajax or getJson does not send my cookie (according to Firebug), so I get HTTP 302 returned from the WCF service: Request Headers Host service.ganymedes.com:8008 User-Agent Mozilla/5.0 (Windows; U; Windows NT 6.1; en-US; rv:1.9.1.8) Gecko/20100202 Firefox/3.5.8 (.NET CLR 3.5.30729) Accept application/json, text/javascript, */* Accept-Language en-us,en;q=0.5 Accept-Encoding gzip,deflate Accept-Charset ISO-8859-1,utf-8;q=0.7,*;q=0.7 Keep-Alive 300 Connection keep-alive Referer http://mvc.ganymedes.com:8008/Test Origin http://mvc.ganymedes.com:8008 It's sent when mucking about on the MVC site though: Request Headers Host mvc.ganymedes.com:8008 User-Agent Mozilla/5.0 (Windows; U; Windows NT 6.1; en-US; rv:1.9.1.8) Gecko/20100202 Firefox/3.5.8 (.NET CLR 3.5.30729) Accept text/html,application/xhtml+xml,application/xml;q=0.9,*/*;q=0.8 Accept-Language en-us,en;q=0.5 Accept-Encoding gzip,deflate Accept-Charset ISO-8859-1,utf-8;q=0.7,*;q=0.7 Keep-Alive 300 Connection keep-alive Referer http://mvc.ganymedes.com:8008/Test Cookie GANYMEDES_COOKIE=0106A4A666C8C615FBFA9811E9A6C5219C277D625C04E54122D881A601CD0E00C10AF481CB21FAED544FAF4E9B50C59CDE2385644BBF01DDD4F211FE7EE8FAC2; GANYMEDES_COOKIE=D6569887B7C5B67EFE09079DD59A07A98311D7879817C382D79947AE62B5508008C2B2D2112DCFCE5B8D4C61D45A109E61BBA637FD30315C2D8353E8DDFD4309 I also put the exact same settings in both applications' web.config files (self-generated validationKey and decryptionKey).

    Read the article

  • overriding enumeration base type using pragma or code change

    - by vprajan
    Problem: I am using a big C/C++ code base which works on gcc & visual studio compilers where enum base type is by default 32-bit(integer type). This code also has lots of inline + embedded assembly which treats enum as integer type and enum data is used as 32-bit flags in many cases. When compiled this code with realview ARM RVCT 2.2 compiler, we started getting many issues since realview compiler decides enum base type automatically based on the value an enum is set to. http://www.keil.com/support/man/docs/armccref/armccref_Babjddhe.htm For example, Consider the below enum, enum Scale { TimesOne, //0 TimesTwo, //1 TimesFour, //2 TimesEight, //3 }; This enum is used as a 32-bit flag. but compiler optimizes it to unsigned char type for this enum. Using --enum_is_int compiler option is not a good solution for our case, since it converts all the enum's to 32-bit which will break interaction with any external code compiled without --enum_is_int. This is warning i found in RVCT compilers & Library guide, The --enum_is_int option is not recommended for general use and is not required for ISO-compatible source. Code compiled with this option is not compliant with the ABI for the ARM Architecture (base standard) [BSABI], and incorrect use might result in a failure at runtime. This option is not supported by the C++ libraries. Question How to convert all enum's base type (by hand-coded changes) to use 32-bit without affecting value ordering? enum Scale { TimesOne=0x00000000, TimesTwo, // 0x00000001 TimesFour, // 0x00000002 TimesEight, //0x00000003 }; I tried the above change. But compiler optimizes this also for our bad luck. :( There is some syntax in .NET like enum Scale: int Is this a ISO C++ standard and ARM compiler lacks it? There is no #pragma to control this enum in ARM RVCT 2.2 compiler. Is there any hidden pragma available ?

    Read the article

  • warning C4996: 'getch': The POSIX name for this item is deprecated

    - by Maziah Mohd Zaki
    1c:\users\user\documents\visual studio 2008\projects\bengkel\bengkel\login.cpp(196) : warning C4996: 'getch': The POSIX name for this item is deprecated. Instead, use the ISO C++ conformant name: _getch. See online help for details. 1 c:\program files\microsoft visual studio 9.0\vc\include\conio.h(145) : see declaration of 'getch' 1c:\users\user\documents\visual studio 2008\projects\bengkel\bengkel\login.cpp(199) : warning C4996: 'getch': The POSIX name for this item is deprecated. Instead, use the ISO C++ conformant name: _getch. See online help for details. 1 c:\program files\microsoft visual studio 9.0\vc\include\conio.h(145) : see declaration of 'getch' 1c:\users\user\documents\visual studio 2008\projects\bengkel\bengkel\login.cpp(203) : warning C4065: switch statement contains 'default' but no 'case' labels 1c:\users\user\documents\visual studio 2008\projects\bengkel\bengkel\login.cpp(225) : warning C4996: 'strcpy': This function or variable may be unsafe. Consider using strcpy_s instead. To disable deprecation, use _CRT_SECURE_NO_WARNINGS. See online help for details. 1 c:\program files\microsoft visual studio 9.0\vc\include\string.h(74) : see declaration of 'strcpy'

    Read the article

  • operator<< overload,

    - by mr.low
    //using namespace std; using std::ifstream; using std::ofstream; using std::cout; class Dog { friend ostream& operator<< (ostream&, const Dog&); public: char* name; char* breed; char* gender; Dog(); ~Dog(); }; im trying to overload the << operator. I'm also trying to practice good coding. But my code wont compile unless i uncomment the using namespace std. i keep getting this error and i dont know. im using g++ compiler. Dog.h:20: error: ISO C++ forbids declaration of ‘ostream’ with no type Dog.h:20: error: ‘ostream’ is neither function nor member function; cannot be declared friend. if i add line using std::cout; then i get this error. Dog.h:21: error: ISO C++ forbids declaration of ‘ostream’ with no type. Can somebody tell me the correct way to overload the << operator with out using namespace std;

    Read the article

  • How to send HTTP get method with headers using CURL

    - by mithunmo
    Hello , I need to send GET Request method with the below headers . I am getting the following capture from HTTP live headers ***http://172.20.22.26/ GET / HTTP/1.1 Host: 172.20.22.26 User-Agent: Mozilla/5.0 (Windows; U; Windows NT 5.1; en-US; rv:1.9.0.1) Gecko/2008070208 Firefox/3.0.1 Accept: text/html,application/xhtml+xml,application/xml;q=0.9,*/*;q=0.8 Accept-Language: en-us,en;q=0.5 Accept-Encoding: gzip,deflate Accept-Charset: ISO-8859-1,utf-8;q=0.7,*;q=0.7 Keep-Alive: 300 Connection: keep-alive Authorization: Basic bWl0aHVuOm1pdGh1bg== HTTP/1.x 200 OK Date: Thu, 01 Jan 2009 00:29:20 GMT Server: HTTPsrv Connection: Keep-Alive Keep-Alive: timeout=30, max=100 Transfer-Encoding: chunked Content-Type: text/html ----------------------------**------------------------------* I am using the following program . It is not working . Please let me know where I am going wrong. <?php $credentials = "mithun:mithun"; $url = "http://172.20.22.26"; $headers = array( "GET /HTTP/1.1", "User-Agent: Mozilla/5.0 (Windows; U; Windows NT 5.1; en-US; rv:1.9.0.1) Gecko/2008070208 Firefox/3.0.1", "Content-type: text/xml;charset=\"utf-8\"", "Accept: text/html,application/xhtml+xml,application/xml;q=0.9,*/*;q=0.8", "Accept-Language: en-us,en;q=0.5", "Accept-Encoding: gzip,deflate", "Accept-Charset: ISO-8859-1,utf-8;q=0.7,*;q=0.7", "Keep-Alive: 300", "Connection: keep-alive", "Authorization: Basic " . base64_encode($credentials)); $ch = curl_init(); curl_setopt($ch, CURLOPT_URL,$url); curl_setopt($ch, CURLOPT_RETURNTRANSFER, 1); curl_setopt($ch, CURLOPT_TIMEOUT, 60); curl_setopt($ch, CURLOPT_HTTPHEADER, $headers); //curl_setopt($ch, CURLOPT_USERAGENT, $defined_vars['HTTP_USER_AGENT']); $data = curl_exec($ch); if (curl_errno($ch)) { print "Error: " . curl_error($ch); } else { // Show me the result var_dump($data); curl_close($ch); }?>

    Read the article

  • RHEL 5.3 Kickstart - How specify location of individual package in Workstation folder?

    - by Ed
    I keep getting "package does not exist" errors during the install. I made a kickstart ISO to create an unattended install of a RHEL 5.3 build machine for C++ software releases. It pulls the kickstart config file from our internal web server. This is handy; it makes it easy to test and modify without having to make a new ISO. And I plan to check it in to version control if I can get it working. Anyway, the rpm packages are located in two folders on the disk; Client and Workstation. The packages install fine for the ones that are physically located under the Client folder. It cannot find those under the Workstation folder such as as doxygen and subversion complaining that packages do not exist. Is there a way to specify the individual package location? # ----------------------------------------------------------------------------- # P A C K A G E S # ----------------------------------------------------------------------------- %packages @gnome-desktop @core @base @base-x @printing @development-tools emacs kexec-tools fipscheck xorg-x11-server-Xnest xorg-x11-server-Xvfb #Packages Located in Workstation Folder *** Install can not find any of these ?? bison doxygen gcc-c++ subversion zlib-devel freetype-devel libxml2-devel Thanks in advance, -Ed

    Read the article

  • PHP Streaming CSV always adds UTF-8 BOM

    - by Mustafa Ashurex
    The following code gets a 'report line' as an array and uses fputcsv to tranform it into CSV. Everything is working great except for the fact that regardless of the charset I use, it is putting a UTF-8 bom at the beginning of the file. This is exceptionally annoying because A) I am specifying iso and B) We have lots of users using tools that show the UTF-8 bom as characters of garbage. I have even tried writing the results to a string, stripping the UTF-8 BOM and then echo'ing it out and still get it. Is it possible that the issue resides with Apache? If I change the fopen to a local file it writes it just fine without the UTF-8 BOM. header("Content-type: text/csv; charset=iso-8859-1"); header("Cache-Control: no-store, no-cache"); header("Content-Disposition: attachment; filename=\"report.csv\""); $outstream = fopen("php://output",'w'); for($i = 0; $i < $report-rowCount; $i++) { fputcsv($outstream, $report-getTaxMatrixLineValues($i), ',', '"'); } fclose($outstream); exit;

    Read the article

  • How to test an application for correct encoding (e.g. UTF-8)

    - by Olaf
    Encoding issues are among the one topic that have bitten me most often during development. Every platform insists on its own encoding, most likely some non-UTF-8 defaults are in the game. (I'm usually working on Linux, defaulting to UTF-8, my colleagues mostly work on german Windows, defaulting to ISO-8859-1 or some similar windows codepage) I believe, that UTF-8 is a suitable standard for developing an i18nable application. However, in my experience encoding bugs are usually discovered late (even though I'm located in Germany and we have some special characters that along with ISO-8859-1 provide some detectable differences). I believe that those developers with a completely non-ASCII character set (or those that know a language that uses such a character set) are getting a head start in providing test data. But there must be a way to ease this for the rest of us as well. What [technique|tool|incentive] are people here using? How do you get your co-developers to care for these issues? How do you test for compliance? Are those tests conducted manually or automatically? Adding one possible answer upfront: I've recently discovered fliptitle.com (they are providing an easy way to get weird characters written "u?op ?pisdn" *) and I'm planning on using them to provide easily verifiable UTF-8 character strings (as most of the characters used there are at some weird binary encoding position) but there surely must be more systematic tests, patterns or techniques for ensuring UTF-8 compatibility/usage. Note: Even though there's an accepted answer, I'd like to know of more techniques and patterns if there are some. Please add more answers if you have more ideas. And it has not been easy choosing only one answer for acceptance. I've chosen the regexp answer for the least expected angle to tackle the problem although there would be reasons to choose other answers as well. Too bad only one answer can be accepted. Thank you for your input. *) that's "upside down" written "upside down" for those that cannot see those characters due to font problems

    Read the article

  • UnsupportedEncodingException thrown when using Resin and Grails

    - by knorv
    I've encountered a strange problem in a Grails webapp running under Grails: java.io.UnsupportedEncodingException is thrown quite frequently due to various unknown encoding strings (such as "ISO8859_10", "ISO-8859-10"), and the strange thing is that this is done entirely within the Resin and Grails code. That is - no custom code is involved when the exception is thrown. I'm not sure if it is Grails or the servlet container's code that should handle the exception. But I'd assume that the exception should be handled somewhere and not bubble up all the way to stderr. This is the exception in full: java.io.UnsupportedEncodingException: ISO-8859-10 at com.caucho.vfs.i18n.JDKWriter$OutputStreamEncodingWriter.<init>(JDKWriter.java:112) at com.caucho.vfs.i18n.JDKWriter.create(JDKWriter.java:79) at com.caucho.vfs.Encoding.getWriteEncoding(Encoding.java:231) at com.caucho.server.connection.ToByteResponseStream.setEncoding(ToByteResponseStream.java:137) at com.caucho.server.connection.AbstractHttpResponse.setLocale(AbstractHttpResponse.java:1683) at com.caucho.server.connection.HttpServletResponseImpl.setLocale(HttpServletResponseImpl.java: 115) at javax.servlet.ServletResponseWrapper.setLocale(ServletResponseWrapper.java:139) at javax.servlet.ServletResponseWrapper.setLocale(ServletResponseWrapper.java:139) at org.springframework.web.servlet.DispatcherServlet.render(DispatcherServlet.java:1035) at org.codehaus.groovy.grails.web.servlet.GrailsDispatcherServlet.doDispatch(GrailsDispatcherServlet.java:290) at org.springframework.web.servlet.DispatcherServlet.doService(DispatcherServlet.java:716) at org.springframework.web.servlet.FrameworkServlet.processRequest(FrameworkServlet.java:647) at org.springframework.web.servlet.FrameworkServlet.doGet(FrameworkServlet.java:552) at javax.servlet.http.HttpServlet.service(HttpServlet.java:114) My questions: Should the exception be handled? If so, is it the responsibility of the servlet container (Resin) or the web framework (Grails)? How would you go about solving this? (I'd rather not having the exception log cluttered with exceptions that I can do nothing about.)

    Read the article

  • RSS feed generated by SharePoint has a stylesheet tag and how to remove that

    - by iHeartDucks
    The feed which SharePoint Generates is here (I copied it to pastie because I thought it would be clear there) However, the xml file comes with a style sheet tag. How do I remove that? Does SharePoint always generate that? Due to the presence of that tag, I am unable to apply another style sheet of my own using the XML WebPart. EDIT: I don't think the issue is related to the style sheet. If I copy the xml and paste it in the "Xml Editor" of the Web Part everything works just fine. If I provide the URL, that is when I do not see any data. This is my XSL file <?xml version="1.0" encoding="ISO-8859-1"?> <xsl:stylesheet version="1.0" exclude-result-prefixes="x d ddwrt xsl msxsl" xmlns:x="http://www.w3.org/2001/XMLSchema" xmlns:d="http://schemas.microsoft.com/sharepoint/dsp" xmlns:ddwrt="http://schemas.microsoft.com/WebParts/v2/DataView/runtime" xmlns:xsl="http://www.w3.org/1999/XSL/Transform" xmlns:msxsl="urn:schemas-microsoft-com:xslt"> <xsl:output method="html" version="1.0" encoding="iso-8859-1" indent="yes"/> <xsl:template match="/"> <xsl:value-of select="count(rss)" /> <xsl:value-of select="count(rss/channel)" /> <xsl:value-of select="count(rss/channel/item)" /> <xsl:for-each select="rss/channel/item"> <xsl:value-of select="title" /> </xsl:for-each> </xsl:template> </xsl:stylesheet> Pastie link

    Read the article

  • latin1/unicode conversion problem with ajax request and special characters

    - by mfn
    Server is PHP5 and HTML charset is latin1 (iso-8859-1). With regular form POST requests, there's no problem with "special" characters like the em dash (–) for example. Although I don't know for sure, it works. Probably because there exists a representable character for the browser at char code 150 (which is what I see in PHP on the server for a literal em dash with ord). Now our application also provides some kind of preview mechanism via ajax: the text is sent to the server and a complete HTML for a preview is sent back. However, the ordinary char code 150 em dash character when sent via ajax (tested with GET and POST) mutates into something more: %E2%80%93. I see this already in the apache log. According to various sources I found, e.g. http://www.tachyonsoft.com/uc0020.htm , this is the UTF8 byte representation of em dash and my current knowledge is that JavaScript handles everything in Unicode. However within my app, I need everything in latin1. Simply said: just like a regular POST request would have given me that em dash as char code 150, I would need that for the translated UTF8 representation too. That's were I'm failing, because with PHP on the server when I try to decode it with either utf8_decode(...) or iconv('UTF-8', 'iso-8859-1', ...) but in both cases I get a regular ? representing this character (and iconv also throws me a notice: Detected an illegal character in input string ). My goal is to find an automated solution, but maybe I'm trying to be überclever in this case? I've found other people simply doing manual replacing with a predefined input/output set; but that would always give me the feeling I could loose characters. The observant reader will note that I'm behind on understanding the full impact/complexity with things about Unicode and conversion of chars and I definitely prefer to understand the thing as a whole then a simply manual mapping. thanks

    Read the article

  • My multipart email script sends HTML messages just fine, but the plain text alternative doesn't not

    - by hsatterwhite
    I have a script set up to send out multipart emails; plain text and html messages. The HTML messages work just fine, but when I used an email client that only does plain text the plaint text message does not render and I get the following: -- This message was generated automatically by Me http://www.somewebsite.com/ $html_msg = $message_details; $plain_text_msg = strip_tags($message_details); $headers = <<<HEADERS From: Me <[email protected]> MIME-Version: 1.0 Content-Type: multipart/alternative; boundary="==PHP-alt$mime_boundary" HEADERS; // Use our boundary string to create plain text and HTML versions $message = <<<MESSAGE --==PHP-alt$mime_boundary Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: 7bit $plain_text_msg -- This message was generated automatically by Me http://www.somewebsite.com/ If you did not request this message, please notify [email protected] --==PHP-alt$mime_boundary Content-Type: text/html; charset="iso-8859-1" Content-Transfer-Encoding: 7bit <html> <body> $html_msg <p> --<br /> This message was generated automatically as a demonstration on <a href="http://www.somewebsite.com/">Me</a> </p> <p> If you did not request this message, please notify <a href="mailto:[email protected]">[email protected]</a> </p> </body> </html> --==PHP-alt$mime_boundary-- MESSAGE;

    Read the article

  • Issue encondig java->xls

    - by Xerg
    This is not a pure java question and can also be related to HTML I've written a java servlet that queries a database table and shows the result as a html table. The user can also ask to receive the result as an Excel sheet. Im creating the Excel sheet by printing the same html table, but with the content-type of "application/vnd.ms-excel". The Excel file is created fine. The problem is that the tables may contain non-english data so I want to use a UTF-8 encoding. PrintWriter out = response.getWriter(); response.setContentType("application/vnd.ms-excel:ISO-8859-1"); //response.setContentType("application/vnd.ms-excel:UTF-8"); response.setHeader("cache-control", "no-cache"); response.setHeader("Content-Disposition", "attachment; filename=file.xls"); out.print(src); out.flush(); The non-english characters appear as garbage (áéíóú) Also I tried converting to bytes from String byte[] arrByte = src.getBytes("ISO-8859-1"); String result = new String(arrByte, "UTF-8"); But I Still getting garbage, What can I do?. Thanks

    Read the article

< Previous Page | 369 370 371 372 373 374 375 376 377 378 379 380  | Next Page >