Search Results

Search found 16587 results on 664 pages for 'virtual hardware'.

Page 401/664 | < Previous Page | 397 398 399 400 401 402 403 404 405 406 407 408  | Next Page >

• Restored Domain Controller does not display any information using dcdiag command

  - by dasko

  I am testing restoring a domain controller from system state backup to different hardware in a non production environment as a sanity check for our restoration procedure. When i run the dcdiag command I get "blank info back" and all that is displayed are two lines as follows: Domain Controller Diagnosis Performing initial setup: and then I am returned to the command prompt. Even when I do dcdiag /v i get the same result. I have double checked the DNS settings and Active Directory works properly. All FSMO roles are being held by this restored Domain Controller. I am able to join test pc's to the domain without issue etc Is this a common issue or is there something that I am missing. Thanks.

  Read the article

• Hyper-V VMs hanging 10 minutes after startup

  - by Ken George

  Hyper-V running under a fresh install of 2008 R2 DC 2 VMs both running 2008 R2 STD One VM has SQL 2008 Server w/ SP2 and Office 2007 Enterprise w/ SP2 Othe VMS only Office 2007 w/ SP2. Approximately 10 minutes after reboot the Hyuper-V host the VMs will hang Hang = answers pings, but no RDP connections and Hyper-V console session is non responsive Disabled Hyper-V and had no proble with 2008 R2 DC host. Started the three Hyper-V services and 10 minutes later was hung again. Hardware is HP DL380 G4 2 socket, 48 GB, Internal SAS controller 1.5TB C drive VMs .VHDs are on external SAS controller on a 1.5 TB RAID5 volume. Nothing in event log on either VMs or Hyper-V host. Ken

  Read the article

• Windows Media Center says "Searching for tuners" when I try to play live TV

  - by Louis

  After upgrading from Windows 8 Pro with Media Center to the 8.1 preview, I need some help in being able to watch live TV again. When I try to now, it says Please Wait. Searching for tuners. I tried reinstalling the software for the Hauppauge WinTV DCR-2650 TV tuner, and upgrading the firmware for both the tuner and the Cisco STA-1520 tuning adapter. I also tried swapping around the USB ports, cold-booting the devices, and running the Set Up TV Signal setting in WMC, but that says The TV signal cannot be configured because a TV tuner was not detected. Both devices look fine in Device Manager, reporting the "This device is working properly" status. I'm not sure if this is related, but I did have some network connectivity issues immediately after upgrading to Windows 8.1 where my either my subnet mask or default gateway was missing, and since the TV tuner shows up as a network device, I wonder if that might be related. However, I really don't know how those settings should look and Hyper-V sort of further complicates things with the virtual Ethernet adapters:

  Read the article

• Why doesn’t windows explorer show my removable / USB drive even though the command prompt does?

  - by Gishu

  I'm running WinXP SP2. Around 50% of the time, when I slot in my USB drive. Windows explorer refuses to show the drive. If I click on the Safely remove hardware icon on the tray, I can see a menu item for the drive - say drive G: (the light on the USB drive is also on) If I type in G: into the address bar of explorer, it says 'Cannot find...' If I type in G: into a command prompt window, it works and I can do a dir to see the list of directories on the drive. To fix this, I've to remove-reinsert the pen-drive. But doing it every day is annoying. Also this happens only on this machine.. I use this drive on my home machine and it works flawlessly each time. Can anyone suggest things that I could try ? Thanks for reading...

  Read the article

• What's the performance on USB docking stations, and can they be used when laptop is closed?

  - by David

  I'm looking into a docking station for a Dell Studio laptop. I don't see the traditional docking stations I'm familiar with - the kind (for a Dell Latitude, for example) where you sit the laptop on top of a long row of pins. Instead, I'm seeing a lot of USB docking stations. When I close my laptop, I want it to go into sleep mode. If I then connect a USB docking station to the laptop while it's closed, will it wake up? What's the performance on USB 2.0 docking stations with a new Dell Studio? Can all of the video and internet traffic really go through a USB 2.0 connection while still providing the best video frame rates and internet speeds? When you undock, I assume you'd have to use the "Safely Remove Hardware" feature in Windows. Will that successfully 'remove' everything attached to the docking station - external drives, thumb drives, etc?

  Read the article

• Best solution for Multi-WAN failover (inside & out)?

  - by Sean O

  Looking for a way to setup 2 ISPs in failover mode, for both incoming & outgoing traffic, for our small (<100 devices) network. The leading contender for now seems to be the Peplink Balance 310. However, a reseller I spoke with said it's great for 100% outgoing connectivity, but didn't seem to be confident in its abilities to handle incoming traffic. This is important as we host our own web site, Exchange e-mail, and virtual desktops (RDP). Do any Peplink owners use this for failover of incoming traffic? Are there other devices I should be considering? We're currently using a Cisco 1800 series router & ASA 5500 series firewall, with Comcast & T-1 lines (the goal being to replace the T with DSL/FiOS {whenever that becomes availble}). Price range: ~$1000 - $2500 USD. Thanks.

  Read the article

• ESX hosts lose connectivity with iSCSI SAN LUNs

  - by Themist

  I've been experiencing this issue for a couple of months now where my ESX hosts lose connectivity with my iSCSI SAN vmfs volumes. As a results the ESX hosts enter a nonresponsive mode the associated VMs disconnect and the only remedy is to reboot the host. This issue happens randomly . I have escalated this issue with VMWare but I haven't had any solution to the issue yet. I see no errors on my switches and there are no hardware issues as well. My SAN infrastucture is solid and there are 2 paths for every vmfs volume. Did anybody else experienced a similar issue? Themis

  Read the article

• Tomcat and GlassfishV3

  - by mikkiman

  I have one Tomcat and one Glassfish-Instance running on one server. Further i have two domains , for example www.abc.com and www.bcd.com. Now i should realise a configuration, that one application of tomcat will use www.abc.com and the second domain www.bcd.com. Is this possible with mod_proxy or mod_jk or something other? I didnt understand exactly how i must realise this. With two virtual-server-tags in apache2... or..? Maybe somewhere knows, how a situation like that is to implement.. Thanks a lot. Mikkman

  Read the article

• Driverless printer sharing on Windows.

  - by MiffTheFox

  I have a printer hooked up to a computer running Windows XP. It prints fine from that computer, but I'd like to set up other computers (running Vista and 7) to print from it as well. I tried setting up printer sharing, but it wouldn't work because the client computers needed to install the print driver as well. (The driver itself has been discontinued and there's no version for Vista or 7.) Is there some (hopefully free) software I can install to, say, add a virtual printer that sends the data to a host computer to print it, rather then having to directly access the printer over the network via the Windows printer sharing model?

  Read the article

• Ubuntu mount hard drive confusing

  - by Fresheyeball

  I'm new to linux and have a home server set up running ubuntu. In the ui its very easy to mount my additional internal harddrives. I just double click on them. Since I have made this server headless, I now need to mount via the command line. How can I replicate the very simple double click gui behavior? So far all the information I've found is very complex. Ubuntu auto generated folders for each hd in under /media and I can see the harddrives under /dev but have no idea which is which as the hardware is identical between them. I also don't know how they are formated. Thanks in advance for any advice you have.

  Read the article

• What are good values for PSU voltages?

  - by earlz

  Hello, I have an odd computer I'm trying to fix that will crash only during the setup of an OS(crashes on every OS I've tried so far) It's not overheating and it is stripped down as much as possible and I've tried multiple harddrives, and memtest86+ can run on it for 3 hours without a crash or fail. So, I was a bit stumped and was looking in the BIOS for possible causes and found a hardware monitor that shows PSU voltages. They are: VCORE: 1.432V 3.3V: 3.136V 5V: 5.273 12V: 12.144V I thought the 3.3V looked a little low, but I'm not really sure on how "bad" that is. So, what are the good ranges for the voltages on each CPU rail?

  Read the article

• Intel Core i5-2467m - Turbo Boost not activating?

  - by Trevor Sullivan

  I have a Samsung Series 5 laptop with an Intel Core i5-2467m process @ 1.6Ghz. The processor supports Intel Turbo Boost up to 2.30 Ghz according to the specifications. The i5-2467m is a dual-core process with HyperThreading, so there is a total of four (4) virtual cores in Windows 7 SP1. http://ark.intel.com/products/56858/ I've installed the Intel Turbo Boost Technology Monitor v2.6 to monitor if Turbo Boost is enabled, and set it to "Always On Top." I followed this process to max out the CPU: Open (4x) PowerShell instances Set each instance's affinity to a distinct CPU vCore Ran this code in each instance: while (1 -eq 1) { } Unfortunately, after maxing out all 4 cores, my laptop got hot, but Turbo Boost never kicked in. Any ideas on how to ensure that I'm getting the 2.3Ghz Turbo Boost capability of my laptop?

  Read the article

• What does NT_STATUS_BAD_NETWORK_NAME mean in Samba?

  - by Neil

  I set up a share like this: [global] security = user map to guest = Bad Password usershare allow guests = yes [vms] comment = VirtualBox Virtual Machines path = /home/neil/VirtualBox/HardDisks guest ok = yes read only = yes And when I access the share as myself, and type in my password, it works fine: $ smbclient //neil-ubuntu/vms -U neil Enter neil's password: Domain=[SHUTTERSTOCK] OS=[Unix] Server=[Samba 3.4.0] smb: \> But when I access it as guest, it doesn't work: $ smbclient //neil-ubuntu/vms -U guest Enter guest's password: Domain=[SHUTTERSTOCK] OS=[Unix] Server=[Samba 3.4.0] tree connect failed: NT_STATUS_BAD_NETWORK_NAME Regardless of what password I type in. Does anyone know why? Also, why does smbclient print such useless error messages?

  Read the article

• How to emulate wireless in Virtualbox?

  - by huahsin68

  I have WinXP install in virtualbox which host in Linux. I have a TP-Link (TP-WN321G) USB wifi adapter and have the driver installed inside WinXP. When I plug-in the wifi adapter, there is an option show "Ralink 802.11g WLAN [0101]" in the virtualbox's USB icon, tick on that option, the Device Manager able to detect the hardware which shows TP-Link, but when look into the properties, it says there is no driver was install. I did try to install Ralink driver but still no luck. Just curious why my wifi adapter is TP-Link, but the option show Ralink? May I know how can I emulate the wireless network inside WindowsXP?

  Read the article

• DNS Server and Private HTTP / SOCKS Proxy

  - by DucDigital

  Hi every one, this is just a small hacking attemp to our router. I'm trying to setup a small DNS and forward webpages through proxy behind the scene. I've successfully implement the DNS server that will do the resolving or anything involved in address resolve. But is there anyway I can forward the user using DNS to a proxy instead of request directly to the server? Are there any software/opensource that I can use? I notice on paid wireless, they can provide a login page if user is not login yet, i think this is a way of implementing proxy. Also the hardware is very basic with linksys and netgear router which connect directly to the internet. It's a basic LAN

  Read the article

• DNS Server and Private HTTP / SOCKS Proxy

  - by DucDigital

  Hi every one, this is just a small hacking attemp to our router. I'm trying to setup a small DNS and forward webpages through proxy behind the scene. I've successfully implement the DNS server that will do the resolving or anything involved in address resolve. But is there anyway I can forward the user using DNS to a proxy instead of request directly to the server? Are there any software/opensource that I can use? I notice on paid wireless, they can provide a login page if user is not login yet, i think this is a way of implementing proxy. Also the hardware is very basic with linksys and netgear router which connect directly to the internet. It's a basic LAN

  Read the article

• panic! apache2 cannot start due to unable to read error.log !

  - by vvvvvvv

  apache2 fails to start because it cannot open error.log I've checked the syslog, and found something troubling... Jan 20 02:58:18 unassigned sm-mta[3559]: o0FAD04C017861: to=<[email protected]>, delay=4+22:45:18, xdelay=00:06:18, mailer=esmtp, pri=63390823, relay=asdfa$ Jan 20 03:00:01 unassigned /USR/SBIN/CRON[3939]: (root) CMD (if [ -x /usr/bin/vnstat ] && [ `ls /var/lib/vnstat/ | wc -l` -ge 1 ]; then /usr/bin/vnstat -u; f$ Jan 20 03:00:01 unassigned /USR/SBIN/CRON[3944]: (smmsp) CMD (test -x /etc/init.d/sendmail && /usr/share/sendmail/sendmail cron-msp) Jan 20 03:00:01 unassigned /USR/SBIN/CRON[3949]: (www-data) CMD ([ -x /usr/lib/cgi-bin/awstats.pl -a -f /etc/awstats/awstats.conf -a -r /var/log/apache/acces$ Jan 20 03:02:48 unassigned kernel: [371919.642705] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0 Jan 20 03:02:48 unassigned kernel: [371919.642754] ata3.00: BMDMA stat 0x24 Jan 20 03:02:48 unassigned kernel: [371919.642779] ata3.00: cmd 25/00:08:37:59:e2/00:00:42:00:00/e0 tag 0 dma 4096 in Jan 20 03:02:48 unassigned kernel: [371919.642780] res 51/01:00:37:59:e2/01:00:42:00:00/e0 Emask 0x1 (device error) Jan 20 03:02:48 unassigned kernel: [371919.642824] ata3.00: status: { DRDY ERR } Jan 20 03:02:48 unassigned kernel: [371919.657647] ata3.00: configured for UDMA/133 Jan 20 03:02:48 unassigned kernel: [371919.657661] ata3: EH complete Jan 20 03:02:50 unassigned kernel: [371921.857580] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0 Jan 20 03:02:50 unassigned kernel: [371921.857620] ata3.00: BMDMA stat 0x24 Jan 20 03:02:50 unassigned kernel: [371921.857645] ata3.00: cmd 25/00:08:37:59:e2/00:00:42:00:00/e0 tag 0 dma 4096 in Jan 20 03:02:50 unassigned kernel: [371921.857646] res 51/01:00:37:59:e2/01:00:42:00:00/e0 Emask 0x1 (device error) Jan 20 03:02:50 unassigned kernel: [371921.857688] ata3.00: status: { DRDY ERR } Jan 20 03:02:50 unassigned kernel: [371921.881468] ata3.00: configured for UDMA/133 Jan 20 03:02:54 unassigned kernel: [371921.881479] ata3: EH complete Jan 20 03:02:54 unassigned kernel: [371924.081382] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0 Jan 20 03:02:54 unassigned kernel: [371924.081417] ata3.00: BMDMA stat 0x24 Jan 20 03:02:54 unassigned kernel: [371924.081443] ata3.00: cmd 25/00:08:37:59:e2/00:00:42:00:00/e0 tag 0 dma 4096 in Jan 20 03:02:54 unassigned kernel: [371924.081444] res 51/01:00:37:59:e2/01:00:42:00:00/e0 Emask 0x1 (device error) Jan 20 03:02:54 unassigned kernel: [371924.081487] ata3.00: status: { DRDY ERR } Jan 20 03:02:54 unassigned kernel: [371924.105252] ata3.00: configured for UDMA/133 Jan 20 03:02:54 unassigned kernel: [371924.105261] ata3: EH complete Jan 20 03:02:54 unassigned kernel: [371933.656925] sd 2:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB) Jan 20 03:02:54 unassigned kernel: [371933.656941] sd 2:0:0:0: [sda] Write Protect is off Jan 20 03:02:54 unassigned kernel: [371933.656944] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00 Jan 20 03:02:54 unassigned kernel: [371933.656956] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA Jan 20 03:02:54 unassigned kernel: [371933.656972] sd 2:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB) Jan 20 03:02:54 unassigned kernel: [371933.656979] sd 2:0:0:0: [sda] Write Protect is off Jan 20 03:02:54 unassigned kernel: [371933.656982] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00 Jan 20 03:02:54 unassigned kernel: [371933.656993] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA Jan 20 03:03:34 unassigned kernel: [371966.060069] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0 Jan 20 03:05:48 unassigned kernel: [371971.776846] ata3.00: BMDMA stat 0x24 Jan 20 03:05:48 unassigned kernel: [371971.776871] ata3.00: cmd 25/00:18:87:10:ee/00:00:42:00:00/e0 tag 0 dma 12288 in Jan 20 03:05:48 unassigned kernel: [371971.776872] res 51/01:00:87:10:ee/01:00:42:00:00/e0 Emask 0x1 (device error) Jan 20 03:05:48 unassigned kernel: [371971.776914] ata3.00: status: { DRDY ERR } Jan 20 03:05:48 unassigned kernel: [371971.800668] ata3.00: configured for UDMA/133 Jan 20 03:05:48 unassigned kernel: [371971.800687] ata3: EH complete Jan 20 03:05:48 unassigned kernel: [371974.157850] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0 Jan 20 03:05:48 unassigned kernel: [371974.157885] ata3.00: BMDMA stat 0x24 Jan 20 03:05:48 unassigned kernel: [371974.157911] ata3.00: cmd 25/00:18:87:10:ee/00:00:42:00:00/e0 tag 0 dma 12288 in Jan 20 03:05:48 unassigned kernel: [371974.157912] res 51/01:00:88:10:ee/01:00:42:00:00/e0 Emask 0x1 (device error) Jan 20 03:05:48 unassigned kernel: [371974.157956] ata3.00: status: { DRDY ERR } Jan 20 03:05:48 unassigned kernel: [371974.179773] ata3.00: configured for UDMA/133 Jan 20 03:05:48 unassigned kernel: [371974.179786] ata3: EH complete Jan 20 03:05:48 unassigned kernel: [371976.398570] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0 Jan 20 03:05:48 unassigned kernel: [371976.398610] ata3.00: BMDMA stat 0x24 Jan 20 03:05:48 unassigned kernel: [371976.398635] ata3.00: cmd 25/00:18:87:10:ee/00:00:42:00:00/e0 tag 0 dma 12288 in Jan 20 03:05:48 unassigned kernel: [371976.398636] res 51/01:00:88:10:ee/01:00:42:00:00/e0 Emask 0x1 (device error) Jan 20 03:05:48 unassigned kernel: [371976.398678] ata3.00: status: { DRDY ERR } Jan 20 03:05:48 unassigned kernel: [371976.423477] ata3.00: configured for UDMA/133 Jan 20 03:05:48 unassigned kernel: [371976.423495] sd 2:0:0:0: [sda] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK Jan 20 03:05:48 unassigned kernel: [371976.423498] sd 2:0:0:0: [sda] Sense Key : Medium Error [current] [descriptor] Jan 20 03:05:48 unassigned kernel: [371976.423501] Descriptor sense data with sense descriptors (in hex): Jan 20 03:05:48 unassigned kernel: [371976.423503] 72 03 13 00 00 00 00 0c 00 0a 80 00 00 00 00 00 Jan 20 03:05:48 unassigned kernel: [371976.423508] 42 ee 10 88 Jan 20 03:05:48 unassigned kernel: [371976.423510] sd 2:0:0:0: [sda] Add. Sense: Address mark not found for data field Jan 20 03:05:48 unassigned kernel: [371976.423515] end_request: I/O error, dev sda, sector 1122898056 Jan 20 03:05:48 unassigned kernel: [371976.423536] ata3: EH complete Jan 20 03:05:48 unassigned kernel: [371978.630504] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0 Jan 20 03:05:48 unassigned kernel: [371978.630547] ata3.00: BMDMA stat 0x24

  Read the article

• Gateway SX2300-01u CPU/PSU issues

  - by Vlad

  I have a 2-yr-old Gateway SX2300-01u with an AMD Phenom X3 8550 that I feel has about a year or so of life left, but I am having a couple of hardware issues that I have not been able to resolve. First, the power supply fan sounds like much louder than before and the PSU itself is really hot. The PSU model (Liteon PS 5221-06) is not available at a reasonable price; are there any good alternatives? Could I replace just the PSU fan? Also, the CPU fan failed sometime back, but my replacement, which supposedly fits the MB (Socket AM2+) doesn't actually fit properly. Any idea why?

  Read the article

• IIS7 returns 403.1 (execute access denied) for image file

  - by Kristoffer

  I have a web app running in IIS7 on Windows Server 2008. There is a virtual directory pointing to a shared folder "/Content/Data" on another machine (running Windows Server 2003), as well as a real directory "/Content/Images" on the local machine (web app sub folder). Accessing images in "/Content/Images" is no problem, but when an image (e.g. a JPEG file) in the "/Content/Data" is accessed by a browser, IIS returns this error: HTTP Error 403.1 - Forbidden: Execute access is denied. However, the web app can read and write to / from it. I assume IIS and ASP.NET are running under different user accounts? Does anyone have an idea on what I have to do to make it work? I have set the permissions on the shared folder to Everyone Full Control, with no luck.

  Read the article

• Apache port forwarding with ZTE ZXV10 W300 router (provider specific firmware)

  - by dannote

  I'm trying to configure port forwarding for Apache 2.2 installed on Windows XP SP3 with ZTE ZXV10 W300 router. The computer has a static IP 192.168.1.2. Port forwarding is configured as following: Enable true Name Apache Protocol TCP (also tried TCP and UPD) WAN Host Start IP Address empty WAN Host End IP Address empty WAN Connection stream WAN Start Port 8080 WAN End Port 8080 LAN Host IP Address 192.168.1.2 LAN Host Start Port 8080 LAN Host End Port 8080 Port 8080 is open for both TCP and UPD in Windows Brandmauer. Apache configuration: Listen 192.168.1.2:8080 Router Firmware: Hardware Version V1.0.01 Software Version V8.0.02T03_CFA Boot Loader Version V1.1.2 The provider is COMSTAR. I'm not sure but it's said they flash routers with modified firmware. I have also tried to set up Bitcomet port forwarding on port 13514 and failed.

  Read the article

• Apache2 Service started twice

  - by Relentless

  My apache2 web-server starts twice and wont bind, so i have to do this: sudo netstat -nap | grep 0.0.0.0:443 sudo kill -9 1243 sudo /etc/init.d/apache2 restart Is there any way i can make a script out of the code above so that i can run automatically on start up? I have Ubuntu 10.04, this happened after an update. UPDATE: ports.conf - Could this be cause it: <IfModule mod_ssl.c> # If you add NameVirtualHost *:443 here, you will also have to change # the VirtualHost statement in /etc/apache2/sites-available/default-ssl # to <VirtualHost *:443> # Server Name Indication for SSL named virtual hosts is currently not # supported by MSIE on Windows XP. Listen 443 </IfModule> <IfModule mod_gnutls.c> Listen 443 </IfModule> could it be listening to 443 twice? or do i need to add NameVirtualHost *:443

  Read the article

• Which tools should I use to work efficiently on a remote server?

  - by Konstantin

  I rented a virtual ubuntu server and am trying to setup a web application. I am working from ubuntu. I know how to use the command line, but it is slow and as a visual person, I prefer graphical interfaces. So I connected with nautilus via ssh and was now able to browse the directories graphically. But my permissions are just those of "other", so I cannot do much without o+rwx. What tools do you use to do setup and administrate your servers? Should I write code locally rather then directly on the server and rsync it? EDIT: It is NOT a production server, I am simply fiddling around there.

  Read the article

• how to bypass internal DNS?

  - by fabjoa

  This is about Ubuntu but should be pretty much the same on all Linux flavors. Let's say I add an entry to my /etc/hosts such as 127.0.1.12 facebook.com and an Apache virtual host such as <VirtualHost 127.0.1.12> ServerName facebook.com DocumentRoot /var/www </VirtualHost> when i open my browser and send a GET request to facebook.com, firefox will browse my /var/www folder. Question: How could I fetch (ie, using wget in bash) the real facebook.com domain - without erasing the entry in /etc/hosts nor my Apache VirtualHost -- IOW how could I bypass internal DNS?

  Read the article

• Linux networking "jail" for a single process

  - by halp

  I need to tune up a networking app for network specific things like: make it use a DNS server different than the default one from /etc/resolv.conf make sure it does not try to connect to certain hosts/ports using tcp/udp connections I know I can get away with just modifying /etc/resolv.conf and writing some iptables rules, but going for a default DENY firewall policy for outgoing IP packets can trigger malfunctions in other services running on the server. I know I can set up a virtual machine with a whole OS and run my app there, but it seems a bit overkill. Is it possible to have a networking "jail" for a single app (think single Linux process) that could accept iptables-like rules for network traffic (think in terms of IP packets and above) allowed to and from this particular app? Maybe this is achievable through some dynamically loaded library that can deal with the networking layer, the same manner tsocks does, but more fine-grained?

  Read the article

• OpenIndiana (illumos): vmxnet3 interface lost on reboot

  - by protomouse

  I want my VMware vmxnet3 interface to be brought up with DHCP on boot. I can manually configure the NIC with: # ifconfig vmxnet3s0 plumb # ipadm create-addr -T dhcp vmxnet3s0/v4dhcp But after creating /etc/dhcp.vmxnet3s0 and rebooting, the interface is down and the logs show: Aug 13 09:34:15 neumann vmxnet3s: [ID 654879 kern.notice] vmxnet3s:0: getcapab(0x200000) -> no Aug 13 09:34:15 neumann vmxnet3s: [ID 715698 kern.notice] vmxnet3s:0: stop() Aug 13 09:34:17 neumann vmxnet3s: [ID 654879 kern.notice] vmxnet3s:0: getcapab(0x200000) -> no Aug 13 09:34:17 neumann vmxnet3s: [ID 920500 kern.notice] vmxnet3s:0: start() Aug 13 09:34:17 neumann vmxnet3s: [ID 778983 kern.notice] vmxnet3s:0: getprop(TxRingSize) -> 256 Aug 13 09:34:17 neumann vmxnet3s: [ID 778983 kern.notice] vmxnet3s:0: getprop(RxRingSize) -> 256 Aug 13 09:34:17 neumann vmxnet3s: [ID 778983 kern.notice] vmxnet3s:0: getprop(RxBufPoolLimit) -> 512 Aug 13 09:34:17 neumann nwamd[491]: [ID 605049 daemon.error] 1: nwamd_set_unset_link_properties: dladm_set_linkprop failed: operation not supported Aug 13 09:34:17 neumann vmxnet3s: [ID 654879 kern.notice] vmxnet3s:0: getcapab(0x20000) -> no Aug 13 09:34:17 neumann nwamd[491]: [ID 751932 daemon.error] 1: nwamd_down_interface: ipadm_delete_addr failed on vmxnet3s0: Object not found Aug 13 09:34:17 neumann nwamd[491]: [ID 819019 daemon.error] 1: nwamd_plumb_unplumb_interface: plumb IPv4 failed for vmxnet3s0: Operation not supported on disabled object Aug 13 09:34:17 neumann nwamd[491]: [ID 160156 daemon.error] 1: nwamd_plumb_unplumb_interface: plumb IPv6 failed for vmxnet3s0: Operation not supported on disabled object Aug 13 09:34:17 neumann nwamd[491]: [ID 771489 daemon.error] 1: add_ip_address: ipadm_create_addr failed on vmxnet3s0: Operation not supported on disabled object Aug 13 09:34:17 neumann nwamd[491]: [ID 405346 daemon.error] 9: start_dhcp: ipadm_create_addr failed for vmxnet3s0: Operation not supported on disabled object I then tried disabling network/physical:nwam in favour of network/physical:default. This works, the interface is brought up but physical:default fails and my network services (e.g. NFS) refuse to start. # ifconfig -a lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1 inet 127.0.0.1 netmask ff000000 vmxnet3s0: flags=1004843<UP,BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 9000 index 2 inet 192.168.178.248 netmask ffffff00 broadcast 192.168.178.255 vmxnet3s0:1: flags=1004842<BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 9000 index 2 inet 192.168.178.248 netmask ffffff00 broadcast 192.168.178.255 vmxnet3s0:2: flags=1004842<BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 9000 index 2 inet 192.168.178.248 netmask ffffff00 broadcast 192.168.178.255 vmxnet3s0:3: flags=1004842<BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 9000 index 2 inet 192.168.178.248 netmask ffffff00 broadcast 192.168.178.255 vmxnet3s0:4: flags=1004842<BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 9000 index 2 inet 192.168.178.248 netmask ffffff00 broadcast 192.168.178.255 vmxnet3s0:5: flags=1004842<BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 9000 index 2 inet 192.168.178.248 netmask ffffff00 broadcast 192.168.178.255 vmxnet3s0:6: flags=1004842<BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 9000 index 2 inet 192.168.178.248 netmask ffffff00 broadcast 192.168.178.255 vmxnet3s0:7: flags=1004842<BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 9000 index 2 inet 192.168.178.248 netmask ffffff00 broadcast 192.168.178.255 vmxnet3s0:8: flags=1004842<BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 9000 index 2 inet 192.168.178.248 netmask ffffff00 broadcast 192.168.178.255 lo0: flags=2002000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv6,VIRTUAL> mtu 8252 index 1 inet6 ::1/128 vmxnet3s0: flags=20002000840<RUNNING,MULTICAST,IPv6> mtu 9000 index 2 inet6 ::/0 # cat /var/svc/log/network-physical\:default.log [ Aug 16 09:46:39 Enabled. ] [ Aug 16 09:46:41 Executing start method ("/lib/svc/method/net-physical"). ] [ Aug 16 09:46:41 Timeout override by svc.startd. Using infinite timeout. ] starting DHCP on primary interface vmxnet3s0 ifconfig: vmxnet3s0: DHCP is already running [ Aug 16 09:46:43 Method "start" exited with status 96. ] NFS server not running: # svcs -xv network/nfs/server svc:/network/nfs/server:default (NFS server) State: offline since August 16, 2012 09:46:40 AM UTC Reason: Service svc:/network/physical:default is not running because a method failed. See: http://illumos.org/msg/SMF-8000-GE Path: svc:/network/nfs/server:default svc:/milestone/network:default svc:/network/physical:default Reason: Service svc:/network/physical:nwam is disabled. See: http://illumos.org/msg/SMF-8000-GE Path: svc:/network/nfs/server:default svc:/milestone/network:default svc:/network/physical:nwam Reason: Service svc:/network/nfs/nlockmgr:default is disabled. See: http://illumos.org/msg/SMF-8000-GE Path: svc:/network/nfs/server:default svc:/network/nfs/nlockmgr:default See: man -M /usr/share/man -s 1M nfsd Impact: This service is not running. I'm new to the world of Solaris, so any help solving would be much appreciated. Thanks!

  Read the article

< Previous Page | 397 398 399 400 401 402 403 404 405 406 407 408  | Next Page >