Search Results

Search found 36619 results on 1465 pages for 'damn small linux'.

Page 404/1465 | < Previous Page | 400 401 402 403 404 405 406 407 408 409 410 411  | Next Page >

  • /etc/init.d/libvirtd start fails but service libvirtd start works. Why?

    - by Gregg
    CentOS 6.3, running as root (Shush). Can you please tell me why I would get initialisation failures from the init scripts but the service command works a treat? There was nothing in /var/log/messages or /var/log/libvirt/* all I have it the Terminal output: /etc/init.d/libvirtd start Starting libvirtd daemon: libvirtd: initialization failed [FAILED] I changed the libvirtd logging level to 1, the highest, but saw nothing in messages after another failure.

    Read the article

  • DRBD not syncing between my nodes when IP is reset

    - by ramdaz
    I am trying to setup DRBD by following the article at http://www.howtoforge.com/setting-up-network-raid1-with-drbd-on-ubuntu-11.10-p2 I am using Ubuntu 10.04 DRBD - 8.3.11 In the first run I had everything working perfectly and when shifting the systems to a production environment I decided to restart the Meta Data creation part and start from scratch. The IPs had changed entirely in the production environment. Issuing drdbadm create-md r0 in both the servers runs successfully. But when I do "drbdadm -- --overwrite-data-of-peer primary all" on the primary it fails to start the re sync. My config file is as given below resource r0 { protocol C; syncer { rate 50M; } startup { wfc-timeout 15; degr-wfc-timeout 60; } net { cram-hmac-alg sha1; shared-secret "aklsadkjlhdbskjndsf8738734jkfkjfkjf"; } on primaryds { device /dev/drbd0; disk /dev/md2; address 172.16.7.1:7788; meta-disk internal; } on secondaryds { device /dev/drbd0; disk /dev/md2; address 172.16.7.3:7788; meta-disk internal; } } Status on primary root at primaryds:~# cat /proc/drbd version: 8.3.7 (api:88/proto:86-91) GIT-hash: ea9e28dbff98e331a62bcbcc63a6135808fe2917 build by root at primaryds, 2012-05-12 15:08:01 0: cs:WFBitMapS ro:Primary/Secondary ds:UpToDate/Inconsistent C r---- ns:0 nr:0 dw:0 dr:200 al:0 bm:0 lo:0 pe:0 ua:0 ap:0 ep:1 wo:b oos:5690352828 Status on secondary root at secondaryds:/etc/drbd.d# cat /proc/drbd version: 8.3.7 (api:88/proto:86-91) GIT-hash: ea9e28dbff98e331a62bcbcc63a6135808fe2917 build by root at secondaryds, 2012-05-12 15:25:25 0: cs:WFBitMapT ro:Secondary/Primary ds:Inconsistent/UpToDate C r---- ns:0 nr:0 dw:0 dr:0 al:0 bm:0 lo:0 pe:0 ua:0 ap:0 ep:1 wo:b oos:5690352828 Log of Primary May 30 13:42:23 primaryds kernel: [ 1584.057076] block drbd0: role( Secondary -> Primary ) disk( Inconsistent -> UpToDate ) May 30 13:42:23 primaryds kernel: [ 1584.086264] block drbd0: Forced to consider local data as UpToDate! May 30 13:42:23 primaryds kernel: [ 1584.086303] block drbd0: Creating new current UUID May 30 13:42:26 primaryds kernel: [ 1586.405551] block drbd0: drbd_sync_handshake: May 30 13:42:26 primaryds kernel: [ 1586.405564] block drbd0: self E8A075F378173D4B:0000000000000004:0000000000000000:0000000000000000 bits:1422588207 flags:0 May 30 13:42:26 primaryds kernel: [ 1586.405574] block drbd0: peer 0000000000000004:0000000000000000:0000000000000000:0000000000000000 bits:1422588207 flags:0 May 30 13:42:26 primaryds kernel: [ 1586.405582] block drbd0: uuid_compare()=2 by rule 30 May 30 13:42:26 primaryds kernel: [ 1586.405587] block drbd0: Becoming sync source due to disk states. May 30 13:42:26 primaryds kernel: [ 1586.405592] block drbd0: Writing the whole bitmap, full sync required after drbd_sync_handshake. May 30 13:42:27 primaryds kernel: [ 1588.171638] block drbd0: 5427 GB (1422588207 bits) marked out-of-sync by on disk bit-map. May 30 13:42:27 primaryds kernel: [ 1588.172769] block drbd0: conn( Connected -> WFBitMapS ) Log in Secondary May 30 13:42:24 secondaryds kernel: [ 1563.304894] block drbd0: peer( Secondary - Primary ) pdsk( Inconsistent - UpToDate ) May 30 13:42:24 secondaryds kernel: [ 1563.339674] block drbd0: drbd_sync_handshake: May 30 13:42:24 secondaryds kernel: [ 1563.339685] block drbd0: self 0000000000000004:0000000000000000:0000000000000000:0000000000000000 bits:1422588207 flags:0 May 30 13:42:24 secondaryds kernel: [ 1563.339695] block drbd0: peer E8A075F378173D4B:0000000000000004:0000000000000000:0000000000000000 bits:1422588207 flags:0 May 30 13:42:24 secondaryds kernel: [ 1563.339703] block drbd0: uuid_compare()=-2 by rule 20 May 30 13:42:24 secondaryds kernel: [ 1563.339709] block drbd0: Becoming sync target due to disk states. May 30 13:42:24 secondaryds kernel: [ 1563.339714] block drbd0: Writing the whole bitmap, full sync required after drbd_sync_handshake. May 30 13:42:26 secondaryds kernel: [ 1565.652342] block drbd0: 5427 GB (1422588207 bits) marked out-of-sync by on disk bit-map. May 30 13:42:26 secondaryds kernel: [ 1565.652965] block drbd0: conn( Connected - WFBitMapT ) The serves are not responding once it reaches this stage. Tried redoing it couple of time but noting happens. Why could the resync not be taking place? I would like some advice? Directions?

    Read the article

  • p2v v2v v2p tool from open source?

    - by neolix
    we have centos, fedora, ubuntu server and desktop we are looking for good open source tool for p2v v2v v2p and we are not using vmware here only we use xen or kvm. Same of the server shifted to new hardware and same of the server on xen or kvm. Can same help me !!

    Read the article

  • Basic clarification about Limited FTP/sFTP users

    - by mattewre
    I would like to get some clarification about the correct way to create limited users to access to my VPS user as WEBSERVER with Nginix. I'm used to NOT install FTP and access via SFTP only. It is ok for every set up? this is what I usually do from to create a limited user called "admin" that should be able to have access via SFTP to the folder with the website data mkdir -p /var/www/mysite.com/ adduser admin adduser admin www-data chown -R root:root /var/www chmod -R 755 /var/www chmod -R 755 /var/www/mysite.com chown -R admin:www-data /var/www/mysite.com/ It seems not to be the correct way, I always have problems with permission when I upload some files (for example with Wordpress in general). I would like to create an user that does work exactly as the one that the "provides" give to their client when they buy an Hosting service (that is a FTP, I would prefer SFTP access). It is for personal user, but I think that a limited user is a lot safer to use then the "root" via SFTP.

    Read the article

  • What kernel modules are required for wi-fi to work?

    - by Leonid Shevtsov
    My custom-built 2.6.32 kernel cannot connect to any WPA-protected network. The kernel includes (probably?) everything that should be needed for wifi, including IPv4 network support (IPv6 is disabled), the ath5k wireless driver (which is used in the generic Ubuntu 2.6.31 kernel) and all crypto APIs. The card is being detected, however, iwlist scan returns wlan0 Failed to read scan data : Network is down and network-manager log says <info> (wlan0): driver supports SSID scans (scan_capa 0x01). <info> (wlan0): new 802.11 WiFi device (driver: 'ath5k') <info> (wlan0): exported as /org/freedesktop/NetworkManager/Devices/1 <info> (wlan0): now managed <info> (wlan0): device state change: 1 -> 2 (reason 2) <info> (wlan0): bringing up device. <info> (wlan0): preparing device. <info> (wlan0): deactivating device (reason: 2). supplicant_interface_acquire: assertion `mgr_state == NM_SUPPLICANT_MANAGER_STATE_IDLE' failed <info> modem-manager is now available <WARN> default_adapter_cb(): bluez error getting default adapter: The name org.bluez was not provided by any .service files <info> Trying to start the supplicant... <info> (wlan0): supplicant manager state: down -> idle <info> (wlan0): device state change: 2 -> 3 (reason 0) <WARN> nm_supplicant_interface_add_cb(): Unexpected supplicant error getting interface: wpa_supplicant couldn't grab this interface. The exact same configuration works with the generic kernel. Is anything except wifi and crypto api needed for wi-fi to work?

    Read the article

  • How to display a graph only for business hours with CACTI?

    - by Blast Raider
    I have noticed that I can only display an uninterrupted period with Cacti. I am wondering whether is possible or not to make a custom graph which displaying only the business hours during a period (a week, a month, etc.). If it is possible, how could I configure it on Cacti ? For example, I would like to be able to display a graph with an average inbound/outbound traffic between 8am and 7pm for 5 business days a week of the last month. I would apreciate any help. Thank you.

    Read the article

  • Unable to boot fedora 11

    - by csunwold
    I have been running fedora 11 for several months without a hiccup, but two days ago I ran "yum update" and installed whatever updates were available (I didn't pay attention to what they were). I was having problems with mysql so I tried "yum remove mysql" and then it removed mysql as well as quite a few unexpected dependencies. I then "yum install mysql" without a hitch and went about my way. However, when I next booted up my machine it got to "Starting preload dameon [OK]" and then it hangs with a flashing cursor on the screen. I tried following http://dailypackage.fedorabook.com/i...ling-Grub.html but it didn't seem to make any difference. I put a new hard drive with WinXP on it into the same machine that I booted to, and I tried to use Ext2 Installable File System for Windows but when I run it, it only seems to see /boot and nothing else on the hard drive. Any ideas?

    Read the article

  • MySQL Master - Master Broken

    - by Recc
    I've Inherited a Mysql master master system, I've noticed the second master (lets call it slave from now on as it's running on a 'slave' machine) stopped getting its db's updated. I saw that Master: Slave_IO_Running: Yes Slave_SQL_Running: Yes Slave: (with an error I truncated) Slave_IO_Running: Yes Slave_SQL_Running: No Last_Errno: 1062 Last_Error: Error 'Duplicate entry '3' for key 'PRIMARY'' on [...] I don't know what caused it to process considering we cant get duplicate there. What's important is to resume normal operations; Right now I've stop slave; on the Master and stop slave; on the Slave because I saw that if I change records on the Slave the changes Do Get Propagated to Master which is in active use. How do I: Force sync EVERYTHING from master to slave without affecting data on master? Then hopefully have slave pickup replication as usual? UPDATE OK I Tried deleting all tables on slave then it complained in that error section that the 'table' doesnt exist. So i made a no data dump of Master, and made sure I have only empty tables in Secondary (slave). I start slave; on slave BUT now it's complaining about bloody alter table statements for instance: Last_Errno: 1060 Last_Error: Error 'Duplicate column name [...] Query: 'ALTER TABLE [...] How to skip the fracking alter statements I just want to replicate the bloody data and be done with it, my tables have the lates changes already FFS and now its complaining about changes made after the replication seized weeks ago How do I reset the log or something? OUTSTANDING Why would this start happening? The "Secondary" is propagating to "Primary". "Primary" is not propagating to "Secondary". But any fixes I tried to do left it in the same state Yes-Yes Yes-No with same Last_Error. I think around that time the server was taken off the network, could that confuse MySQL in some way?

    Read the article

  • External monitor image not centered in the screen

    - by kemp
    I'm using Xorg 7.5 on a Radeon HD4870 with the FOSS radeonhd server on my HP 6830s. The laptop has a VGA connector and I attach it to a 37" panasonic plasma TV. It works fine except for a little annoyance: when activated, the TV screen is set to the resolution of 1360x768 (which it reports as being the highest it supports) but all the image is shifted by about 100 pixels to the right. I can't see the leftmost part of the page, and I have a black vertical bar to the right. If I change the resolution to 1024x768 there is no shifting, the image fills the entire screen with no parts hidden, but at this resolution the image is stretched. How can I tune the position on the external monitor so that the image is centered in the screen filling it entirely?

    Read the article

  • ACL and moving files in Nautilus

    - by MyOnlyEye
    When I move files from a private home directory (e.g. /home/jack) to a shared directory (e.g. /home/shared-school) Nautilus copies the file permissions from the original file into the shared directory - and ignores the ACL that I've put in the /home/shared-school directory (e.g. setfacl -R -m d:g:school:rwx /home/shared-school). Is it possible to force Nautilus to change ACL on a file that is moved or copied - or not to ignore the ACL on the directory where the files are moved or copied?

    Read the article

  • pg_dump not working - do I need to change order of $PATH?

    - by A4J
    I'm trying to set the $PATH to pick up the latest version of pg_dump as I'm currently getting a mismatch error while doing a migrate in my Rails app (I recently changed the schema type to SQL). I have added a new file in /etc/profile.d called pg_dump.sh, and inside that put: PG_DUMP=/usr/pgsql-9.1 export PG_DUMP PATH=$PATH:$PG_DUMP/bin export PATH On looking at echo $PATH, I get: /usr/local/rvm/gems/ruby-1.9.3-p194/bin:/usr/local/rvm/gems/ruby-1.9.3-p194@global/bin:/usr/local/rvm/rubies/ruby-1.9.3-p194/bin:/usr/local/rvm/bin:/usr/local/sbin:/usr/local/bin:/sbin:/bin:/usr/sbin:/usr/bin:/usr/pgsql-9.1/bin:/root/bin And I still get the error. Do I need to change the order? If so any ideas how? Output of 'ls /usr/pgsql-9.1/bin': clusterdb droplang pg_archivecleanup pg_ctl pg_standby psql createdb dropuser pg_basebackup pg_dump pg_test_fsync reindexdb createlang ecpg pgbench pg_dumpall pg_upgrade vacuumdb createuser initdb pg_config pg_resetxlog postgres vacuumlo dropdb oid2name pg_controldata pg_restore postmaster And output of 'which pg_dump': /usr/bin/pg_dump Error message on running cap 'deploy:migrate': ** [out :: 46.4.9.199] pg_dump: server version: 9.1.4; pg_dump version: 8.4.11 ** [out :: 46.4.9.199] pg_dump: aborting because of server version mismatch ** [out :: 46.4.9.199] rake aborted! ** [out :: 46.4.9.199] Error dumping database output of 'pg_dump --version': pg_dump (PostgreSQL) 8.4.11

    Read the article

  • My mail going on spam from SMTP server

    - by user1767434
    I am trying to send a registration confirmation mail from my site to user who are registering from my site. my code is:- $drg_name = addslashes(trim($_POST['drg_name'])); $drg_surname = addslashes(trim($_POST['drg_surname'])); $drg_email = addslashes(trim($_POST['drg_email'])); $drg_username = addslashes(trim($_POST['drg_username'])); $drg_pass = addslashes(base64_encode($_POST['drg_pass'])); $drg_addr1 = addslashes(trim($_POST['drg_addr1'])); $drg_addr2 = addslashes(trim($_POST['drg_addr2'])); $drg_addr3 = addslashes(trim($_POST['drg_addr3'])); $drg_town = addslashes(trim($_POST['drg_town'])); $drg_county = addslashes(trim($_POST['drg_county'])); $drg_zip = addslashes(trim($_POST['drg_zip'])); $drg_country = addslashes(trim($_POST['drg_country'])); $drg_phone = addslashes(trim($_POST['drg_phone'])); $drg_gender = addslashes(trim($_POST['drg_gender'])); $drg_pstatus = addslashes(trim($_POST['drg_pstatus'])); $drg_dod = addslashes(trim($_POST['drg_dod'])); $drg_dom = addslashes(trim($_POST['drg_dom'])); $drg_doy = addslashes(trim($_POST['drg_doy'])); $drg_dob=$drg_dod.'/'.$drg_dom.'/'.$drg_doy; $drg_question = addslashes(trim($_POST['drg_question'])); $drg_answer = addslashes(trim($_POST['drg_answer'])); //send confirmation email to user to activate his/her acc $encoded_usr_id=base64_encode($usr_id); $en_id=base64_encode($insert_id); $subject = "Confirmation From dragonsnet.biz" ; $message = "Thank you to register with dragonsnet.biz<br>\n In order to >activate your account please click here: http://My SITE URL/registration_success.php?envar=".$encoded_usr_id."&euid=".$en_id."' Activate\n Thank you for taking the time to register to the dragonsnet.biz Website. "; $this->_globalObj->send_email('support@ MY-Site', $drg_email, $subject, $message, 'Site Name'); $cnf=base64_encode("confirmation"); die($this->_globalObj->redirect("registration_confirmation.php?eml=$cnf")); } my mail is going in user mail ID but in Spam not in inbox. Please help Thanks In Advance.

    Read the article

  • Triple monitor setting in Linux with USB-HDMI adapter

    - by Oscar Carballal
    I'm trying to set up a triple monitor desktop at my office using Fedora 17, but it seems impossible, let me explain the setting: Laptop ASUS K53SD with 2 graphic cards, Intel and nVidia (Screen controled by Intel card) 24" Full HD monitor connected to the HDMI output (controlled by Intel card) 23" Full HD monitor connected to an USB-HDMI adapter (via framebuffer in /dev/fb2, apparently) VGA output (not used) controlled by nVidia card First of all, the USB-HDMI adapter works perfectly, it gives me a green screen (which means the communication is OK) and I can make it work if I set up a single monitor setting via framebuffer in Xorg. Here I leave the page where I got the instructions: http://plugable.com/2011/12/23/usb-graphics-and-linux Now I'm trying to set up the the two main monitors (laptop and 24") with the intel driver and the 23" with the framebuffer, but the most succesful configuration I get is the two main monitors working and the third disconnected. Do you have any idea what can I do to make this work? Here I leave my xRandr output and my Xorg conf: -> xrandr Screen 0: minimum 320 x 200, current 3286 x 1080, maximum 8192 x 8192 LVDS1 connected 1366x768+0+0 (normal left inverted right x axis y axis) 344mm x 193mm 1366x768 60.0*+ 1024x768 60.0 800x600 60.3 56.2 640x480 59.9 VGA2 disconnected (normal left inverted right x axis y axis) HDMI1 connected 1920x1080+1366+0 (normal left inverted right x axis y axis) 531mm x 299mm 1920x1080 60.0*+ 50.0 25.0 30.0 1680x1050 59.9 1680x945 60.0 1400x1050 74.9 59.9 1600x900 60.0 1280x1024 75.0 60.0 1440x900 75.0 59.9 1280x960 60.0 1366x768 60.0 1360x768 60.0 1280x800 74.9 59.9 1152x864 75.0 1280x768 74.9 60.0 1280x720 50.0 60.0 1440x576 25.0 1024x768 75.1 70.1 60.0 1440x480 30.0 1024x576 60.0 832x624 74.6 800x600 72.2 75.0 60.3 56.2 720x576 50.0 848x480 60.0 720x480 59.9 640x480 72.8 75.0 66.7 60.0 59.9 720x400 70.1 DP1 disconnected (normal left inverted right x axis y axis) 1920x1080_60.00 60.0 The Xorg file: # Xorg configuration file for using a tri-head display Section "ServerLayout" Identifier "Layout0" Screen 0 "HDMI" 0 0 Screen 1 "USB" RightOf "HDMI" Option "Xinerama" "on" EndSection ########### MONITORS ################ Section "Monitor" Identifier "USB1" VendorName "Unknown" ModelName "Acer 24as" Option "DPMS" EndSection Section "Monitor" Identifier "HDMI1" VendorName "Unknown" ModelName "Acer 23SH" Option "DPMS" EndSection ########### DEVICES ################## Section "Device" Identifier "Device 0" Driver "intel" BoardName "GeForce" BusID "PCI:0:02:0" Screen 0 EndSection Section "Device" Identifier "USB Device 0" driver "fbdev" Option "fbdev" "/dev/fb2" Option "ShadowFB" "off" EndSection ############## SCREENS ###################### Section "Screen" Identifier "HDMI" Device "Device 0" Monitor "HDMI1" DefaultDepth 24 SubSection "Display" Depth 24 EndSubSection EndSection Section "Screen" Identifier "USB" Device "USB Device 0" Monitor "USB1" DefaultDepth 24 SubSection "Display" Depth 24 EndSubSection EndSection

    Read the article

  • ubuntu input/output error

    - by rplevy
    I'm having a problem with Ubuntu that I'm finding hard to troubleshoot for reasons that will become clear: reboot -bash: /sbin/reboot: Input/output error dmesg -bash: /bin/dmesg: Input/output error ps -e ps: error while loading shared libraries: /lib/libproc-3.2.8.so: cannot read file data: Input/output error lsof -bash: /usr/bin/lsof: Input/output error fsck -bash: /sbin/fsck: Input/output error badblocks -bash: /sbin/badblocks: Input/output error So I can't see what is going on, and I can't remotely reboot. What can I do to get to the bottom of this? Interestingly: init 0 Segmentation fault I can cat /var/syslog but not /var/log/messages or several other important files. less and more don't work, neither do tail or head, etc.

    Read the article

  • (manually configured) kernel update leaves wireless in a mess

    - by Mala
    I recently upgraded my kernel from 2.6.31-gentoo-r6 to 2.6.32-gentoo-r7. In both cases, I configured everything manually. However, since the upgrade, my wireless card appears to be on the fritz. It will connect to networks just fine, and remain connected, but can only access the internet (and other hosts on the network) for about 3 seconds after connecting. Reconnecting to the network appears to fix the problem... for another 3 seconds or so. The problem is "solved" by booting into the older kernel. The relevant lspci entry is 02:00.0 Network controller: Intel Corporation PRO/Wireless 5300 AGN [Shiloh] Network Connection I'm pretty sure I have the correct drivers enabled in the kernel Device Drivers ---> Network device support ---> Wireless LAN (IEEE 802.11) ---> <*> Intel Wireless Wifi [*] Enable LED support in iwlagn and iwl3945 drivers [*] Enable Spectrum Measurement in iwlagn driver [*] Enable full debugging output in iwlagn and iwl3945 drivers <*> Intel Wireless WiFi Next Gen AGN (iwlagn) [*] Intel Wireless WiFi 4965AGN [*] Intel Wireless WiFi 5000AGN; Intel WiFi Link 1000, 6000, and 6050 Series I tried with the other intel drivers enabled as well (iwl3945) and no difference. Is there something stupid I'm missing? Is there something I have to recompile after upgrading the kernel (a la nvidia)? Thanks Mala

    Read the article

  • postfix smtp relay script

    - by Peter Sander
    I have a Postfix server and using it with Outlook (POP/SMTP). I have different sender addresses for an account. Now I want to configure a relay for a specific sender address. For example I have postfix for my main domain domain1.com. Now I have a sender address that is domain2.com. For that sender address I want that postfix to relay mail to a second SMTP server. I think that should be possible without problems. But the problem is that I have to create a SSH tunnel to the second server to connect to the SMTP server. But I cant use a persistent SSH connection so I want to know if it is possible that postfix executes some script before relaying the mail to the second SMTP server. I already found some information for executing a script when incomming emails but I only want to establish the SSH tunnel before postfix relays the mail to the second SMTP server.

    Read the article

  • external disk suddenly unmounting

    - by hasen j
    Platform: Ubuntu 9.10 Disk Brand/model: WD My Book The external hard disk suddenly unmounts after a while. I suspect it's due to it "sleeping" to save power. I don't recall the problem having occurred before the upgrade to Karmic. How can this be fixed?

    Read the article

  • Simple mdadm RAID 1 not activating spare

    - by Nick Liu
    I had created two 2TB HDD partitions (/dev/sdb1 and /dev/sdc1) in a RAID 1 array called /dev/md0 using mdadm on Ubuntu 12.04 LTS Precise Pangolin. The command sudo mdadm --detail /dev/md0 used to indicate both drives as active sync. Then, for testing, I failed /dev/sdb1, removed it, then added it again with the command sudo mdadm /dev/md0 --add /dev/sdb1 watch cat /proc/mdstat showed a progress bar of the array rebuilding, but I wouldn't spend hours watching it, so I assumed that the software knew what it was doing. After the progress bar was no longer showing, cat /proc/mdstat displays: md0 : active raid1 sdb1[2](S) sdc1[1] 1953511288 blocks super 1.2 [2/1] [U_] And sudo mdadm --detail /dev/md0 shows: /dev/md0: Version : 1.2 Creation Time : Sun May 27 11:26:05 2012 Raid Level : raid1 Array Size : 1953511288 (1863.01 GiB 2000.40 GB) Used Dev Size : 1953511288 (1863.01 GiB 2000.40 GB) Raid Devices : 2 Total Devices : 2 Persistence : Superblock is persistent Update Time : Mon May 28 11:16:49 2012 State : clean, degraded Active Devices : 1 Working Devices : 2 Failed Devices : 0 Spare Devices : 1 Name : Deltique:0 (local to host Deltique) UUID : 49733c26:dd5f67b5:13741fb7:c568bd04 Events : 32365 Number Major Minor RaidDevice State 1 8 33 0 active sync /dev/sdc1 1 0 0 1 removed 2 8 17 - spare /dev/sdb1 I've been told that mdadm automatically replaces removed drives with spares, but /dev/sdb1 isn't being moved into the expected position, RaidDevice 1. UPDATE (30 May 2012): A badblocks destructive read-write test of the entire /dev/sdb yielded no errors as expected; both HDDs are new. As of the latest edit, I assembled the array with this command: sudo mdadm --assemble --force --no-degraded /dev/md0 /dev/sdb1 /dev/sdc1 The output was: mdadm: /dev/md0 has been started with 1 drive (out of 2) and 1 rebuilding. Rebuilding looks like it's progressing normally: md0 : active raid1 sdc1[1] sdb1[2] 1953511288 blocks super 1.2 [2/1] [U_] [>....................] recovery = 0.6% (13261504/1953511288) finish=2299.7min speed=14060K/sec unused devices: <none> I'm now waiting on this rebuild, but I'm expecting /dev/sdb1 to become a spare just like the five or six times that I've tried rebuilding before. UPDATE (31 May 2012): Yeah, it's still a spare. Ugh! UPDATE (01 June 2012): I'm trying Adrian Kelly's suggested command: sudo mdadm --assemble --update=resync /dev/md0 /dev/sdb1 /dev/sdc1 Waiting on the rebuild now... My questions are: Why isn't the spare drive becoming active sync? How can I make the spare drive become active?

    Read the article

  • Can a 32-bit RHEL4 userland work with a 64-bit kernel?

    - by James
    Is there a way to change an i386 RHEL4 machine to run an amd64 kernel, but ensure that it still builds software into same i386 binaries? On Debian this seems quite straightforward: just install an amd64 kernel (worst case, build one like this guy: http://www.debian-administration.org/users/jonesy/weblog/1) and prefix everything with "linux32". Then everything that considers uname -m will be unchanged, I just need to handle the few cases that consider uname -r. What is the Red Hat equivalent? Is the only way a full 64-bit installation on another disk and then chrooting back to the 32-bit system before anyone builds anything? (Even the best examples of that seem to be Debian-based.) Background: We make a large system that runs on (a variant of) i386 RHEL4. However, some of the larger RHEL build machines now have enough RAM that they might benefit from going 64-bit (for the kernel and maybe some of the bigger build steps). Our build system doesn't support cross-compilation.

    Read the article

  • GDM login screen is not displayed with VNC

    - by niboshi
    Hi, I set up VNC server with xinetd. Also configured GDM so that XDMCP is enabled. VNC connection seems okay, but GDM login screen is not shown. Instead I can only see old bare X screen (gray meshed background and X-shaped mouse pointer), which I can't do any interaction with it. What can I do to fix the problem? No log is written below /var/log/. Server distribution: Ubuntu marverick /etc/xinetd.d/vnc is like below: service vnc1024 { disable = no socket_type = stream protocol = tcp wait = no user = nobody server = /usr/bin/Xvnc server_args = -inetd -query localhost -geometry 1024x768 -depth 24 -once securitytypes=none port = 12345 } /etc/gdm/custom.conf: [daemon] [security] DisallowTCP=false [xdmcp] Enable=true [gui] [greeter] [chooser] [debug] [servers] /etc/services is also configured. Thanks

    Read the article

  • Apache availability with the two front-ends on diferent locations. Is it possible?

    - by marc.riera
    Hello, I have to locations (office and service providers). One DNS(bind) serving our domain as authoritative, and a service provider webserver with our corporate web on a private server. So.. Now we are planing to upgrade our server on the ISP to a new one, and I would like to use this situation to improve our service. Is it possible to mount a high availability apache/mysql/php within to different locations? I will install a bind slave on the same new server, so I hope it will make things easier, but I need some hints and tips on how to ride it. THanks.

    Read the article

  • Ubuntu 14.04, OpenLDAP TLS problems

    - by larsemil
    So i have set up an openldap server using this guide here. It worked fine. But as i want to use sssd i also need TLS to be working for ldap. So i looked into and followed the TLS part of the guide. And i never got any errors and slapd started fine again. BUT. It does not seem to work when i try to use ldap over tls. root@server:~# ldapsearch -x -ZZ -H ldap://83.209.243.253 -b dc=daladevelop,dc=se ldap_start_tls: Protocol error (2) additional info: unsupported extended operation Ganking up the debug level some notches returns some more information: root@server:~# ldapsearch -x -ZZ -H ldap://83.209.243.253 -b dc=daladevelop,dc=se -d 5 ldap_url_parse_ext(ldap://83.209.243.253) ldap_create ldap_url_parse_ext(ldap://83.209.243.253:389/??base) ldap_extended_operation_s ldap_extended_operation ldap_send_initial_request ldap_new_connection 1 1 0 ldap_int_open_connection ldap_connect_to_host: TCP 83.209.243.253:389 ldap_new_socket: 3 ldap_prepare_socket: 3 ldap_connect_to_host: Trying 83.209.243.253:389 ldap_pvt_connect: fd: 3 tm: -1 async: 0 ldap_open_defconn: successful ldap_send_server_request ber_scanf fmt ({it) ber: ber_scanf fmt ({) ber: ber_flush2: 31 bytes to sd 3 ldap_result ld 0x7f25df51e220 msgid 1 wait4msg ld 0x7f25df51e220 msgid 1 (infinite timeout) wait4msg continue ld 0x7f25df51e220 msgid 1 all 1 ** ld 0x7f25df51e220 Connections: * host: 83.209.243.253 port: 389 (default) refcnt: 2 status: Connected last used: Fri Jun 6 08:52:16 2014 ** ld 0x7f25df51e220 Outstanding Requests: * msgid 1, origid 1, status InProgress outstanding referrals 0, parent count 0 ld 0x7f25df51e220 request count 1 (abandoned 0) ** ld 0x7f25df51e220 Response Queue: Empty ld 0x7f25df51e220 response count 0 ldap_chkResponseList ld 0x7f25df51e220 msgid 1 all 1 ldap_chkResponseList returns ld 0x7f25df51e220 NULL ldap_int_select read1msg: ld 0x7f25df51e220 msgid 1 all 1 ber_get_next ber_get_next: tag 0x30 len 42 contents: read1msg: ld 0x7f25df51e220 msgid 1 message type extended-result ber_scanf fmt ({eAA) ber: read1msg: ld 0x7f25df51e220 0 new referrals read1msg: mark request completed, ld 0x7f25df51e220 msgid 1 request done: ld 0x7f25df51e220 msgid 1 res_errno: 2, res_error: <unsupported extended operation>, res_matched: <> ldap_free_request (origid 1, msgid 1) ldap_parse_extended_result ber_scanf fmt ({eAA) ber: ldap_parse_result ber_scanf fmt ({iAA) ber: ber_scanf fmt (}) ber: ldap_msgfree ldap_err2string ldap_start_tls: Protocol error (2) additional info: unsupported extended operation ldap_free_connection 1 1 ldap_send_unbind ber_flush2: 7 bytes to sd 3 ldap_free_connection: actually freed So no good information there neither. In /var/log/syslog i get: Jun 6 08:55:42 master slapd[21383]: conn=1008 fd=23 ACCEPT from IP=83.209.243.253:56440 (IP=0.0.0.0:389) Jun 6 08:55:42 master slapd[21383]: conn=1008 op=0 EXT oid=1.3.6.1.4.1.1466.20037 Jun 6 08:55:42 master slapd[21383]: conn=1008 op=0 do_extended: unsupported operation "1.3.6.1.4.1.1466.20037" Jun 6 08:55:42 master slapd[21383]: conn=1008 op=0 RESULT tag=120 err=2 text=unsupported extended operation Jun 6 08:55:42 master slapd[21383]: conn=1008 op=1 UNBIND Jun 6 08:55:42 master slapd[21383]: conn=1008 fd=23 closed If i portscan the host i get the following: Starting Nmap 6.40 ( http://nmap.org ) at 2014-06-06 08:56 CEST Nmap scan report for h83-209-243-253.static.se.alltele.net (83.209.243.253) Host is up (0.0072s latency). Not shown: 996 closed ports PORT STATE SERVICE 22/tcp open ssh 80/tcp open http 389/tcp open ldap 636/tcp open ldapssl But when i check certs root@master:~# openssl s_client -connect daladevelop.se:636 -showcerts -state CONNECTED(00000003) SSL_connect:before/connect initialization SSL_connect:unknown state 140244859233952:error:140790E5:SSL routines:SSL23_WRITE:ssl handshake failure:s23_lib.c:177: --- no peer certificate available --- No client certificate CA names sent --- SSL handshake has read 0 bytes and written 317 bytes --- New, (NONE), Cipher is (NONE) Secure Renegotiation IS NOT supported Compression: NONE Expansion: NONE --- And i feel like i am clearly out in deep water not knowing at all where to go from here. Anny hints appreciated on what to do or to get better debug logging... EDIT: This is my config slapcated from cn=config and it does not mention at all anything about TLS. I have inserted my certinfo.ldif: root@master:~# cat certinfo.ldif dn: cn=config add: olcTLSCACertificateFile olcTLSCACertificateFile: /etc/ssl/certs/cacert.pem - add: olcTLSCertificateFile olcTLSCertificateFile: /etc/ssl/certs/daladevelop_slapd_cert.pem - add: olcTLSCertificateKeyFile olcTLSCertificateKeyFile: /etc/ssl/private/daladevelop_slapd_key.pem and when doing that i only got this as an answer. root@master:~# sudo ldapmodify -Y EXTERNAL -H ldapi:/// -f certinfo.ldif SASL/EXTERNAL authentication started SASL username: gidNumber=0+uidNumber=0,cn=peercred,cn=external,cn=auth SASL SSF: 0 modifying entry "cn=config" So still no wiser.

    Read the article

< Previous Page | 400 401 402 403 404 405 406 407 408 409 410 411  | Next Page >