Search Results

Search found 18728 results on 750 pages for 'setup deployment'.

Page 408/750 | < Previous Page | 404 405 406 407 408 409 410 411 412 413 414 415  | Next Page >

  • VPN Network intermittantly fails to provide internet: What could be possible causes

    - by Jake M
    We have a small office with our own VPN setup. We occasionally experience failures in our internet connection where we cannot access the internet. Most of the time the internet connection will resume by itself(without me doing anything) after a period of time(10 mins). Would you be able to suggest possible causes of the connection failure so I can then go and run some tests? Our network architecture is like so: A 'Billion' brand router that is connected to the internet via phone cable and then connected to our Cisco Switch A Cisco Switch/Bus which is connected to all our office nodes, our external harddrive and also to our router as stated above. All connections are via ethernet cable A series of work computers(nodes) connected via ethernet cable to the Cisco switch. Our ISP is TPG Australia We have a Virtual Private Network All the ethernet cables are about 3 years old Do you think that the causes of our intermittant connection problems could be due to the following: Data collisions in the ethernet cables Old/Faulty ethernet cables Our ISP has bad service Can you think of any other causes of the problem?

    Read the article

  • Point dns server to root dns servers [duplicate]

    - by Dhaksh
    This question already has an answer here: What is a glue record? 3 answers Why does DNS work the way it does? 4 answers I have setup a custom authoritative only DNS server using bind9. Its a Master ans Slave method. Assume DNS Servers are: ns1.customdnsserver.com [192.168.91.129] ==> Master ns2.customdnsserver.com [192.168.91.130] ==> Slave Now i will host few shared hosting websites in my own web server. Where i will link above Nameservers to my domains in shared hosting. My Question is: How do i tell root DNS servers about my own authoritative only DNS server? So that when someone queries for domain www.example.com and if the domain's website is hosted in my shared hosting i want root servers to point the query to my own DNS Server so that the www.example.com get resolved for IP address.

    Read the article

  • Make Google chrome with specific user profile as default browser

    - by Kaushik Gopal
    Is it possible to set Google chrome with a custom user profile as the default browser? When I set google chrome as the default browser, it picks the "default" user profile as against the custom one I have setup. I tried setting google chrome as default browser after opening it from that particular user profile, but it doesn't seem to have an effect. I googled around but could only find another poor soul like myself who asked a similar question here: http://www.google.com/support/forum/p/Chrome/thread?tid=69f0a6e776ceab1c&hl=en There weren't any responses to that question. Cheers.

    Read the article

  • Citrix Secure Gateway not redirecting to login URL

    - by Dave
    We have an older setup for XenApp - users log in through Citrix Secure Gateway running on a windows box. (We hope to start using a NetScaler soon.) Earlier today, connections to https://citrix.company.com/ starting throwing up a 503 error page, instead of redirecting to https://citrix.company.com/Citrix/XenApp/ If you go directly to the /Citrix/Xenapp/ URL, the user is properly directed to the login page, and can launch apps. We've restarted the service, and rebooted the server. We haven't yet tried uninstalling and reinstalling the software. Before we do this, I'm looking for ideas as to how we can get the redirect working again without a fairly major outage window. To make things more interesting, many of our users have Citrix Receiver installed, also pointed at https://citrix.company.com/. Receiver makes itself the default launcher for ICA files, and gives a connection error when it tries to load apps - probably because of the same non-functional rediect?

    Read the article

  • ethernet not working

    - by good boy
    i wanted to know how do i setup an ethernet connection on a laptop,my isp gave me a telephone like cable which fits the ethernet port. i guess its the ethernet cable. when i connect it, nothing happens on the pc the ethernet card(realtek pcie gbe family controller) says cable not plugged in. i am using wired connection for first time.the system is completely stable with softwares .the drivers are also automatically updated through a manufacturer installed update system. the isp says there must be some sort of light on the port. whats the problem? how do get it working.

    Read the article

  • configure /etc/hosts file so ALL applications always use local network when it makes sense to do so?

    - by gkdsp
    I have two Linux CentOS servers setup in a local network. ServerA is 192.168.0.1 and serverB is 192.168.0.2. There's an application on serverA that communicates with serverB using host2.serverAname.com. But, the traffic is blocked on serverB because the port being used has a firewall that only allows traffic on the local network to pass. Thus, serverB needs to see traffic from serverA as originating from 192.168.0.1 (instead of host2.serverA.com). Is there a way I can configure the /etc/hosts file to ensure traffic always sent between the two servers uses local IP addresses, regardless of what hostname is in use, and for ALL applications? If so, could someone walk me through an example? I only have 2 servers, so the simpler the better.

    Read the article

  • Could Not Load Type Microsoft.Build.Framework.BuildEventContext

    Setting up a TeamCity build and got this error: C:\Program Files\MSBuild\Microsoft\VisualStudio\v9.0\TeamData\Microsoft.Data.Schema.SqlTasks.targets(80, 5): error MSB4018: The "SqlSetupDeployTask" task failed unexpectedly. System.TypeLoadException: Could not load type 'Microsoft.Build.Framework.BuildEventContext' from assembly 'Microsoft.Build.Framework, Version=2.0.0.0, Culture=neutral, PublicKeyToken=b03f5f7f11d50a3a'. at Microsoft.Build.BuildEngine.TaskExecutionModule.SetBatchRequestSize() at Microsoft.Build.BuildEngine.TaskExecutionModule..ctor(EngineCallback engineCallback, TaskExecutionModuleMode moduleMode, Boolean profileExecution) at Microsoft.Build.BuildEngine.NodeManager..ctor(Int32 cpuCount, Boolean childMode, Engine parentEngine) at Microsoft.Build.BuildEngine.Engine..ctor(Int32 numberOfCpus, Boolean isChildNode, Int32 parentNodeId, String localNodeProviderParameters, BuildPropertyGroup globalProperties, ToolsetDefinitionLocations locations) at Microsoft.Build.BuildEngine.Engine.get_GlobalEngine() at Microsoft.Data.Schema.Build.DeploymentProjectBuilder.CreateDeploymentProject() at Microsoft.Data.Schema.Tasks.DBSetupDeployTask.BuildDeploymentProject(ErrorManager errors, ExtensionManager em) at Microsoft.Data.Schema.Tasks.DBSetupDeployTask.Execute() at Microsoft.Build.BuildEngine.TaskEngine.ExecuteTask(ExecutionMode howToExecuteTask, Hashtable projectItemsAvailableToTask, BuildPropertyGroup projectPropertiesAvailableToTask, Boolean& taskClassWasFound)   The usual searching didnt bring back anything useful, but I figured out that Id missed a dropdownlist in the TeamCity project setup: Originally I was using Microsoft .NET Framework 2.0 for my MSBuild task.  Changing it to 3.5 (as shown above) got me past this error (and on to the next one). Did you know that DotNetSlackers also publishes .net articles written by top known .net Authors? We already have over 80 articles in several categories including Silverlight. Take a look: here.

    Read the article

  • Unable to configure Rails with readline

    - by Liam Berg
    1) ./configure --prefix=$HOME/.packages --with-readline-dir=$HOME/.packages 2) configure: WARNING: unrecognized options: --with-readline-dir I am trying to setup the most up-to-date version of Rails on my webhost (I do not have sudo access). Line 1 is the configure command I used for Ruby and Line 2 is the first printed line after executing 'configure'. I've googled this issue and found other people with the same problem but there aren't any real solutions. There are no warnings or errors when configuring/compiling readline-6.1. I am pretty stumped, any help/insight would be greatly appreciated. Thanks ahead of time.

    Read the article

  • How can I store Rails uploads on a remote server (and not a common cloud host)?

    - by joshee
    I would like to store uploads from a Rails application on a different server than my application server. I want to keep costs to a minimum and host this other server in-house. I am planning to use Carrierwave for uploads. It seems Carrierwave interfaces with Fog for remote hosts. Is there a way I could set the other server to act as a Fog provider? How would I go about this setup? Or, is there some better and easier way to go about all this?

    Read the article

  • How to set up DHCP-configured access through a Linux box?

    - by marcusw
    I would like an old desktop box to use my laptop as a router to access the internet. Here is my setup: I have one ethernet port in the side of my laptop which I want to use to get internet access to my desktop computer. The laptop is connected to the LAN via a wireless link. Both systems run Linux. The desktop autoconfigures itself using DHCP. The laptop is a Kubuntu system. I do not have any crossover cables, though wireshark on the laptop sees the DHCP requests from the desktop just fine, so I doubt that I need one. What do I have to do to make this work?

    Read the article

  • Linux: multiple network connections - 3G/4G / Wifi / LAN / etc; how can i set a preferred network connection to use?

    - by Alex
    I've been looking at how I can setup a laptop that has multiple network interfaces, but a problem exists if all the connections are active, i.e. 3G, WiFi and LAN are all connected, I would like it to default to LAN. I would like to set "weights" or "priority" to each connection, so that if the LAN is unplugged, it'll default to WiFi - if its in range and working, otherwise, it'll switch and use the 3G dongle; I've been looking around and I can see that the "metric" counter for route isn't being used for recent kernels. I thought that would be able to set the preferred gateway / connections - but according to the man page: man route: OUTPUT Metric The 'distance' to the target (usually counted in hops). It is not used by recent kernels, but may be needed by routing daemons. So I'm confused, are there any scripts / apps / anything that can detect active network connections, and by way of configuration, send my default gateway network traffic through that interface if its active / alive?

    Read the article

  • Virtual system drive is split between separate LUNs

    - by Tigran
    My hardware VMWare guy told me that a Win2008R2 server I have has a D drive that is split between two separate LUNs. He could not tell me if that's a good thing or bad just that it's not standard practice for him. Would you please explain the benefits or drawbacks of this setup? Thanks EDIT Some additional info. What happened was I had D drive already allocated. Then I asked for more. They said there's no more space on whatever LUN my D drive is on so the option they gave me was that part of the D drive will be on one LUN and other part will be on another LUN. Hope that helps

    Read the article

  • Digest authentication not working: endless cycles of asking for user/pass

    - by bcmcfc
    I'm trying to setup my SVN repository for access remotely. In doing so I have some settings under Apache's dav_svn.conf file. When navigating to hostname/svn, or using Tortoise to do the same it prompts for the user name and password as expected. However, when entering the correct user name and pass that were set in the password file linked to under AuthUserFile it just asks for the credentials again. I think I'm probably missing something simple? The server is running Ubuntu Server 9.10. Accessing SVN remotely does currently work if the authentication lines of dav_svn.conf are commented out. These are the contents of the dav_svn.conf file: <Location /svn> DAV svn SVNPath /home/svn/repo AuthType Digest AuthName "Subversion Repository" AuthDigestDomain /svn/ AuthUserFile /etc/svn_authfile Require valid-user </Location>

    Read the article

  • How do I built a DIY NAS?

    - by Kaushik Gopal
    I'm looking for good, detailed instructions on how to build a DIY NAS (Network Access Storage). I'm planning on doing it cheap (old PC config + open source software). I would like to know: What hardware I need to built one What kind of hard-drive setup I should take (like RAID) Or any other relevant hardware related advices (power supply, motherboard etc...) What software I should run on it, both what OS and software to manage the contents effectively So the NAS is recognizable and accessible to my network I can make sure my Windows computers will recognize it (when using Linux distro's) I can access my files from outside my network I already did a fair bit of searching and found these links, but while these links are great they delve more on the hardware side. I'm looking for more instructions in the software side. Ubuntu Setting up a Home NAS DIY NAS Smackdown How to Configure an $80 File Server in 45 Minutes FreeNAS Build a NAS Device With an Old PC and Free Software Build Your Own NAS Device

    Read the article

  • open mysql to any connection on ubuntu

    - by ThomasReggi
    I simply want to open up mysql to be accessible from any server ip. I have already commented out the bind-address in /etc/mysql/my.conf. I have already setup the user account within mysql. I have no clue whats stopping me from connecting. The more challenging I see this being the more I realize how much of a security risk it is, and I get that, I just want to be able to do it temporarily. I think that the iptables firewall is the last thing that is preventing me from achieving this, but sudo iptables -A INPUT -p tcp -m tcp --dport 3306 -j ACCEPT is seemingly doing nothing.

    Read the article

  • How to start a task before networking?

    - by user1252434
    I've written an upstart task that modifies /etc/network/interfaces. (Actually a file sourced into it.) Which start on condition do I need to declare to let my task run before any networking jobs? I've tried start on starting networking, but that's apparently too late. When I log in after booting I can see that the changes were written, but obviously they are not used: the new config states a static IP, but the boot process waits for a non-existing DHCP server (old config) to time out. I've also tried start on starting network-interface INTERFACE=eth0, which didn't work either. IIRC there was an error in the log that the change couldn't be written. Background: I need a VM template that can be cloned and the clones configured through a script. Among other settings, I need to give them a static IP address to access them from the host. I use guestfish to write a config file to one of the virtual disks and let a script apply these settings to the system. I don't want that disk to contain an actual system settings file. I can't modify /etc directly, because that disk is shared (copy-on-write/diff) among the clones and guestfish apparently doesn't support that type of image. I could also let them use DHCP and setup a server that assigns IP by MAC, but I'm afraid of the complexity. I could also add just another virtual disk for configuration files, but if possible I'd prefer to store settings directly on the system disk image. Used software: Ubuntu Server 12.04, VirtualBox. The configuration modifier is a self written ruby script.

    Read the article

  • Why use multiple partitions on a rhel server?

    - by Jakobud
    I'm about to reformat and reinstall CentOS onto an old server. The server runs on a modest 30 node small business network and has a variety of responsibilities including MySQL, a Samba share, DHCPd & SVN/Trac. The old sysadmin had this server setup with almost a dozen different partitions for various things. I'm trying to understand what the advantages of multiple partitions are as opposed to a just one filesystem at /. Speed? Flexibility? Security? It seems like if you misjudge the necessary size for any given partition and it ends up filling up too fast, it requires a sysadmin to go in and expand the partition, etc... Seems like it would be easier if everything was just one flat / filesystem. But I'm sure there are some advantages I'm not aware of. The server is currently running a handful of HDDs raided to ~2TB (raid 0).

    Read the article

  • How to execute with /bin/false shell

    - by Amar
    I am trying to setup per-user fastcgi scripts that will run each on a different port and with a different user. Here is example of my script: #!/bin/bash BIND=127.0.0.1:9001 USER=user PHP_FCGI_CHILDREN=2 PHP_FCGI_MAX_REQUESTS=10000 etc... However, if I add user with /bin/false (which I want, since this is about to be something like shared hosting and I don't want users to have shell access), the script is run under 1001, 1002 'user' which, as my Google searches showed, might be a security hole. My question is: Is it possible to allow user(s) to execute shell scripts but disable them so they cannot log in via SSH?

    Read the article

  • Adding lines to /etc/profile with puppet?

    - by miku
    I use puppet to install a current JDK and tomcat. package { [ "openjdk-6-jdk", "openjdk-6-doc", "openjdk-6-jre", "tomcat6", "tomcat6-admin", "tomcat6-common", "tomcat6-docs", "tomcat6-user" ]: ensure => present, } Now I'd like to add JAVA_HOME="/usr/lib/java" export JAVA_HOME to /etc/profile, just to get this out of the way. I haven't found a straightforward answer in the docs, yet. Is there a recommended way to do this? In general, how do I tell puppet to place this file there or modify that file? I'm using puppet for a single node (in standalone mode) just to try it out and to keep a log of the server setup.

    Read the article

  • Practical RAID Performance?

    - by wag2639
    I've always thought the following to be a general rule of thumb for RAID: RAID 0: Best performance for READ and WRITE from stripping, greatest risk RAID 1: Redundant, decent for READ (I believe it can read from different parts of a file from different hard drives), not the best for WRITE RAID 0+1 (01): combines redundancy of RAID 1 with performance of RAID 0 RAID 1+0 (10): slightly better version of RAID 0+1 RAID 5: good READ performance, bad WRITE performance, redundant IS THIS ASSUMPTION CORRECT? (and how do they compare to a JBOD setup for R/W IO performance) Are certain practical RAID setups better for different applications: gaming, video editing, database (Acccess or SQL)? I was thinking about hard disk drives but does this apply to solid state drives as well?

    Read the article

  • ASA 5510 Need to filter traffic log events to my iPhone

    - by drpcken
    For some reason I cannot update apps or download apps to any ios devices on my network (tried both iphone and ipads). When I'm at home on my own network everything works fine. This started about a week ago. I've configured my iphone with a static IP address and even used 4.2.2.2 as my dns to rule out that the issue is with my DNS Server. I'm looking at the SYSLOG in ASDM (Cisco ASA 5510) but Im not sure it is providing me enough info. It seems to be showing ACL blocks on my public ip address, but not individual client IP's, so I can't see whats going on. How can I setup a way to filter any incoming/outgoing traffic to my iPhone's static IP and try and troubleshoot this?

    Read the article

  • MySQL started to consume about 40% of system CPU time and got unresponsive suddenly

    - by Alex
    I use Debian 6.0.3 x86_64 and MySQL 5.5.20-1~dotdeb.0-log from the Dotdeb repository. MySQL process started to consume a lot of "sy" CPU time serveral hours ago according to this graph. I was not able to connect to running mysqld process and had to kill it. I found nothing useful in logs. My setup seems to be quite common (I assume Dotdeb just redistributes stock MySQL versions) and I have never seen anything like this before. What is the possible root cause of this? How can I prevent this situation in the future?

    Read the article

  • Win 2008 R2 Server Not Recognizing Second Hard Drive

    - by Brian
    Hello, I just purchased a Dell server, which has two hard drives and no RAID setup. I can only currently see one hard drive... not sure how to get it to recognize the other, as I thought being a new machine that wouldn't be an issue. It has Windows Server 2008 R2 that I loaded on. I'm a n00b to all of this so I'm not sure why this is failing to work... Any help appreciated. Thanks.

    Read the article

  • Automate Windows 8.1 Enterprise upgrade

    - by Ben M.
    I have been trying to find the necessary command line switches for automating the upgrade for my Windows 8 clients to Windows 8.1. I have the ISO extracted and I've run setup.exe /? but that doesn't tell me enough. I can't find any relevant information from search engines. Can anyone point me to some documentation or information on how to automate the upgrade so that it keeps user data, programs, etc? I know how to do it when running the installer manually, but I obviously do not wish to do that with 100+ machines.

    Read the article

  • Bootstrap a debian build environment and build source packages with no root privileges

    - by Erwan Queffélec
    On debian squeeze, I am trying to do the following : fetch sources package from the wheezy source repository bootstrap a squeeze chroot for several architectures build the packages for several architectures (i386, amd64 + all and any) I want both the fetching, bootstrapping and build operation to be scriptable, repeatable, and run as a normal user. For the environment setup, I want to make as little use of the root account as possible (install the necessary dependencies, and maybe some visudo stuff). If possible I would like to avoid using a VM (pbuilder with user mode linux) So far I have tried several things with pbuilder (require root), debootstrap (require root) with little success. Here is an example script of what I want to do (does not work): #/bin/bash set -e set -x this=`readlink -f $0` this_dir=`dirname $this` archs='i386 amd64 any all' pushd $this_dir/src # I actually want the following line to work with a repo that # is not in /etc/apt/sources.list but that is another question apt-get source cyrus-imapd-2.4 popd for arch in $archs do build_dir=$this_dir/build/$arch/ pbuilder --create --configfile $build_dir/pbuilderrc --buildresult $build_dir/ pbuilder --build --configfile $build_dir/pbuilderrc --buildresult \ $build_dir/ $this_dir/src/*.dsc # of course I want to use the .dput.cf in /home/myuser/ # and not in /root/ dput $build_dir/$arch/*.changes done

    Read the article

< Previous Page | 404 405 406 407 408 409 410 411 412 413 414 415  | Next Page >