Search Results

Search found 33445 results on 1338 pages for 'single instance storage'.

Page 408/1338 | < Previous Page | 404 405 406 407 408 409 410 411 412 413 414 415  | Next Page >

• MySQL Master-Master w/ multiple read slave cost effective setup in AWS

  - by Ross

  I've been evaluating Amazon Web Services RDS for MySQL and costing out potential scenarios involving a simple multi-AZ deployment read/write setup vs. a multi-AZ deployment mysql master (hot-standby) with additional read-only slaves. the issue I'm trying to cost-optimize includes their reserved instance vs on-demand instances. Situation 1: purchase reserved multi-az setup for Extra-large-hi-mem(17GB RAM) instance for $5200/yr and have my application query the master all the time. the problem is, if I don't need all the resources of the (17GB RAM) all the time and therefore, especially not a hot-standby, what alternatives for savings can a better topology create, like potentially situation 2 below: Situation 2: purchase reserved multi-az setup using smaller master instances than above for the master-master hot-standby to receive the writes only. Then create and load balance several read-only slaves off the master and add/remove and/or scale up/down the read slaves based on demand. This might only cost $1000 + the on-demand usage of the read slaves. My thinking is, if I have a variable read-intensive application load, with low write load, the single level topology in situation 1 means I'm paying for a lot of resources at the write level of topology when I don't need them there. My hope is that situation 2 can yield cost savings from smaller reserved instances on the master-master resource level allowing me to scale up and down and/or out on the read-level according to demand as needed. Does anyone see a downside to doing this or know of some reason this isn't possible with RDS? Any other thoughts or advice always welcome of course. Thanks in advance, R

  Read the article

• IPTables configuration for Localhost

  - by Gabe Mc

  I have a problem in connecting a JIRA instance running on a cloud server to an instance of MySQL running on the same box. I have configured it previously using quite a few iptables rules, but it seems overly broad/terribly inprecise. I want access to several of localhosts ports from the local machine, but deny it from all other accounts. Currently, my /etc/iptables.rules file looks like: *filter :INPUT DROP [223:17779] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [10161:1120819] # SSH Access -A INPUT -p tcp -m tcp --dport 22 -j ACCEPT -A INPUT -i eth0 -m state --state RELATED,ESTABLISHED -j ACCEPT # Apache2 Access for connecting to Tomcat on port 8080 -A INPUT -p tcp -m tcp --dport 443 -j ACCEPT # MySQL -I INPUT -i lo -p tcp -m tcp --dport mysql -j ACCEPT COMMIT However, this doesn't allow me to log in when I try logging in; it just hangs on: #> mysql -u root -p -h 127.0.0.1 The Tomcat servlet container starts throwing all kinds of exceptions, as well. This is a more general problem, as I need to enable things like accessing the shutdown port for the Tomcat container, but I need to at least get the MySQL part ironed out first, without the ugliness I was originally trying. Thanks.

  Read the article

• Force local IP traffic to an external interface

  - by calandoa

  I have a machine with several interfaces that I can configure as I want, for instance: eth1: 192.168.1.1 eth2: 192.168.2.2 I would like to forward all the traffic sent to one of these local addresses through the other interface. For instance, all requests to an iperf, ftp, http server at 192.168.1.1 should be not just routed internally, but forwarded through eth2 (and the external network will take care of re-routing the packet to eth1). I tried and looked at several commands, like iptables, ip route, etc... but nothing worked. The closest behavior I could get was done with: ip route change to 192.168.1.1/24 dev eth2 which send all 192.168.1.x on eth2, except for 192.168.1.1 which is still routed internally. May be I could then do NAT forwarding of all traffic directed to fake 192.168.1.2 on eth1, rerouted to 192.168.1.1 internally? I am actually struggling with iptables, but it is too tough for me. The goal of this setup is to do interface driver testing without using two PCs. I am using Linux, but if you know how to do that with Windows, I'll buy it!

  Read the article

• How can I download a copy of an S3 public data set?

  - by tripleee

  i was naively assuming I could do something like s3cmd sync s3://snap-d203feb5 /var/tmp/copy but I seem to have the wrong idea of how to go about this. I cannot even get a simple thing to work; vnix$ s3cmd ls s3://snap-d203feb5 Bucket 'snap-d203feb5': ERROR: Bucket 'snap-d203feb5' does not exist I guess the identifier I have is not for a "bucket" but for a "public data set". How do I go from one to the other? Do I have to start up an EC2 instance and create a bucket for this? How? The instructions at http://docs.amazonwebservices.com/AWSEC2/latest/UserGuide/using-public-data-sets.html seem to assume I want to use the data in an EC2 instance, but in this case, I'd just like to browse a bit, at least for a start. By the by, copy/pasting the "US Snapshot ID" causes a nasty traceback from Python; they publish the ID with a weird Unicode (I presume) dash which cannot directly be copy/pasted. Is there a mistake when I copy it? And what's the significance of "US" in there? Can't I use the data outside North America??

  Read the article

• Formula to calculate probability of unrecoverable read error during RAID rebuild

  - by OlafM

  I need to compare the reliability of different RAID systems with either consumer or enterprise drives. The formula to have the probability of success of a rebuild, ignoring mechanical problems, is simple: error_probability = 1 - (1-per_bit_error_rate)^bit_read and with 3 TB drives I get 38% probability to experience an URE (unrecoverable read error) for a 2+1 disks RAID5 (4.7% for enterprise drives) 21% for a RAID1 (2.4% for enterprise drives) 51% probability of error during recovery for the 3+1 RAID5 often used by users of SOHO products like Synologys. Most people don't know about this. Calculating the error for single disk tolerance is easy, my question concerns systems tolerant to multiple disks failures (RAID6/Z2, RAIDZ3 and RAID1 with multiple disks). If only the first disk is used for rebuild and the second one is read again from the beginning in case or an URE, then the error probability is the one calculated above squared (14.5% for consumer RAID5 2+1, 4.5% for consumer RAID1 1+2). However, I suppose (at least in ZFS that has full checksums!) that the second parity/available disk is read only where needed, meaning that only few sectors are needed: how many UREs can possibly happen in the first disk? not many, otherwise the error probability for single-disk tolerance systems would skyrocket even more than I calculated. If I'm correct, a second parity disk would practically lower the risk to extremely low values. Am I correct?

  Read the article

• jdbc4 CommunicationsException

  - by letronje

  I have a machine running a java app talking to a mysql instance running on the same instance. the app uses jdbc4 drivers from mysql. I keep getting com.mysql.jdbc.exceptions.jdbc4.CommunicationsException at random times. Here is the whole message. Could not open JDBC Connection for transaction; nested exception is com.mysql.jdbc.exceptions.jdbc4.CommunicationsException: The last packet successfully received from the server was25899 milliseconds ago.The last packet sent successfully to the server was 25899 milliseconds ago, which is longer than the server configured value of 'wait_timeout'. You should consider either expiring and/or testing connection validity before use in your application, increasing the server configured values for client timeouts, or using the Connector/J connection property 'autoReconnect=true' to avoid this problem. For mysql, the value of global 'wait_timeout' and 'interactive_timeout' is set to 3600 seconds and 'connect_timeout' is set to 60 secs. the wait timeout value is much higher than the 26 secs(25899 msecs). mentioned in the exception trace. I use dbcp for connection pooling and here is spring bean config for the datasource. <bean id="dataSource" destroy-method="close" class="org.apache.commons.dbcp.BasicDataSource" > <property name="driverClassName" value="com.mysql.jdbc.Driver"/> <property name="url" value="jdbc:mysql://localhost:3306/db"/> <property name="username" value="xxx"/> <property name="password" value="xxx" /> <property name="poolPreparedStatements" value="false" /> <property name="maxActive" value="3" /> <property name="maxIdle" value="3" /> </bean> Any idea why this could be happening? Will using c3p0 solve the problem ?

  Read the article

• Can't sync filesystem without reboot

  - by Fabio

  I'm having an issue with a linux server. Once a week the running mysql instance hangs and there is no way to fully stop it. If I kill it, it remains in zombie status and init does not reap its pid. The server is used for staging deployments and some internal tools, so it's not under heavy load. The only process constantly used id mysql and for this I think that it's the only process which suffer of this issue. I've searched system logs for errors and the only thing I found is this error (repeated a couple of times) in dmesg output: [706560.640085] INFO: task mysqld:31965 blocked for more than 120 seconds. [706560.640198] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [706560.640312] mysqld D ffff88032fd93f40 0 31965 1 0x00000000 [706560.640317] ffff880242a27d18 0000000000000086 ffff88031a50dd00 ffff880242a27fd8 [706560.640321] ffff880242a27fd8 ffff880242a27fd8 ffff88031e549740 ffff88031a50dd00 [706560.640325] ffff88031a50dd00 ffff88032fd947f8 0000000000000002 ffffffff8112f250 [706560.640328] Call Trace: [706560.640338] [<ffffffff8112f250>] ? __lock_page+0x70/0x70 [706560.640344] [<ffffffff816cb1b9>] schedule+0x29/0x70 [706560.640347] [<ffffffff816cb28f>] io_schedule+0x8f/0xd0 [706560.640350] [<ffffffff8112f25e>] sleep_on_page+0xe/0x20 [706560.640353] [<ffffffff816c9900>] __wait_on_bit+0x60/0x90 [706560.640356] [<ffffffff8112f390>] wait_on_page_bit+0x80/0x90 [706560.640360] [<ffffffff8107dce0>] ? autoremove_wake_function+0x40/0x40 [706560.640363] [<ffffffff8112f891>] filemap_fdatawait_range+0x101/0x190 [706560.640366] [<ffffffff81130975>] filemap_write_and_wait_range+0x65/0x70 [706560.640371] [<ffffffff8122e441>] ext4_sync_file+0x71/0x320 [706560.640376] [<ffffffff811c3e6d>] do_fsync+0x5d/0x90 [706560.640379] [<ffffffff811c40d0>] sys_fsync+0x10/0x20 [706560.640383] [<ffffffff816d495d>] system_call_fastpath+0x1a/0x1f When this happens the only way to make everything working again is a full reboot, but in order to do that I'm forced to use this command after I've manually stopped all running processes echo b > /proc/sysrq-trigger otherwise normal reboot process hangs forever. I've tracked reboots script and I've found out that also the reboot process hangs on a sync call, this one in /etc/init.d/sendsigs (I'm on ubuntu) # Flush the kernel I/O buffer before we start to kill # processes, to make sure the IO of already stopped services to # not slow down the remaining processes to a point where they # are accidentily killed with SIGKILL because they did not # manage to shut down in time. sync I'm almost sure that the cause of this is an hardware issue (the RAID controller???) also because I've other two machines with the same hardware and software configuration and they don't suffer of this, but I can't find any hint in syslog or dmesg. I've also installed smartmontools and mcelog packages but none of them did report any issue. What can I do to track the cause of this issue? Today is happened again, here is the status of system after triggering a reboot init---console-kit-dae---64*[{console-kit-dae}] +-dbus-daemon +-mcelog +-mysqld---{mysqld} +-newrelic-daemon---newrelic-daemon---11*[{newrelic-daemon}] +-ntpd +-polkitd---{polkitd} +-python3 +-rpc.idmapd +-rpc.statd +-rpcbind +-sh---rc---S20sendsigs---sync +-smartd +-snmpd +-sshd---sshd---zsh---sudo---zsh---pstree +-sshd---sshd---zsh---sudo---zsh And here is the status of sync process # ps aux | grep sync root 3637 0.1 0.0 4352 372 ? D 05:53 0:00 sync i.e. Uninterruptible sleep... Hardware specs as reported by lshw I think the raid controller is a fake raid. I usually don't deal with hardware (and for the record I don't have physical access to it) description: Computer product: X7DBP () vendor: Supermicro version: 0123456789 serial: 0123456789 width: 64 bits capabilities: smbios-2.4 dmi-2.4 vsyscall32 configuration: administrator_password=disabled boot=normal frontpanel_password=unknown keyboard_password=unknown power-on_password=disabled uuid=53D19F64-D663-A017-8922-0030487C1FEE *-core description: Motherboard product: X7DBP vendor: Supermicro physical id: 0 version: PCB Version serial: 0123456789 *-firmware description: BIOS vendor: Phoenix Technologies LTD physical id: 0 version: 6.00 date: 05/29/2007 size: 106KiB capacity: 960KiB capabilities: pci pnp upgrade shadowing escd cdboot bootselect edd int13floppy2880 acpi usb ls120boot zipboot biosbootspecification *-storage description: RAID bus controller product: 631xESB/632xESB SATA RAID Controller vendor: Intel Corporation physical id: 1f.2 bus info: pci@0000:00:1f.2 version: 09 width: 32 bits clock: 66MHz capabilities: storage pm bus_master cap_list configuration: driver=ahci latency=0 resources: irq:19 ioport:18a0(size=8) ioport:1874(size=4) ioport:1878(size=8) ioport:1870(size=4) ioport:1880(size=32) memory:d8500400-d85007ff

  Read the article

• MacBook Pro (OSX Lion) - shutdown automatically before reaching login screen

  - by mkk

  When I try to lunch my MacBook Pro I can see a progress bar on loading screen. It goes to 1/15 or something like this and then it shut downs - I cannot reach even login screen. It happened to me 2 months ago, I have 'fixed' this by formatting my hard drive and installing OSX (Lion) again. This time I think that situation is a little bit different - I am able to enter single-user mode by pressing cmd + s. I then type /sbin/fsck -yf, I get the error: ** Checking Journaled HFS Plus volume. The volume name is Macintosh HD ** Checking extents overflow file. ** Checking catalog file. Invalid node structure (4, 24704) ** The volume Macintosh HD could not be verified completely. /dev/rdisk0s2 (hfs) EXITED WITH SIGNAL 8 but when I type exit, I can the login screen and I can log in. I tried a lot of things, booting from recovery partition and choosing disk utility to repair the disc, but I get error that it cannot be repaired. I have googled for hours and the only real solution I have found was to buy Disc warrior that might fix the issue. Any other suggestions? Secondary question is what causes this issue? I thought the reason are bad sectors, but Smart Utility haven't found any. I found suggestion that RAM could cause this kind of issue as well, so I downloaded rember and made memory test - all tests passed. Right now I have used my solution of entering single-mode user and then typing exit, however I am not sure how long it will 'work'. Of course I have back-uped what I considered important. Thanks for the help in advance! UPDATE: I guess Smart Utility was not very useful, I mnaged to get input/output error, which I believe is equivalent to bad sector.

  Read the article

• GRE Tunnel over IPsec with Loopback

  - by Alek

  Hello, I'm having a really hard time trying to estabilish a VPN connection using a GRE over IPsec tunnel. The problem is that it involves some sort of "loopback" connection which I don't understand -- let alone be able to configure --, and the only help I could find is related to configuring Cisco routers. My network is composed of a router and a single host running Debian Linux. My task is to create a GRE tunnel over an IPsec infrastructure, which is particularly intended to route multicast traffic between my network, which I am allowed to configure, and a remote network, for which I only bear a form containing some setup information (IP addresses and phase information for IPsec). For now it suffices to estabilish a communication between this single host and the remote network, but in the future it will be desirable for the traffic to be routed to other machines on my network. As I said this GRE tunnel involves a "loopback" connection which I have no idea of how to configure. From my previous understanding, a loopback connection is simply a local pseudo-device used mostly for testing purposes, but in this context it might be something more specific that I do not have the knowledge of. I have managed to properly estabilish the IPsec communication using racoon and ipsec-tools, and I believe I'm familiar with the creation of tunnels and addition of addresses to interfaces using ip, so the focus is on the GRE step. The worst part is that the remote peers do not respond to ping requests and the debugging of the general setup is very difficult due to the encrypted nature of the traffic. There are two pairs of IP addresses involved: one pair for the GRE tunnel peer-to-peer connection and one pair for the "loopback" part. There is also an IP range involved, which is supposed to be the final IP addresses for the hosts inside the VPN. My question is: how (or if) can this setup be done? Do I need some special software or another daemon, or does the Linux kernel handle every aspect of the GRE/IPsec tunneling? Please inform me if any extra information could be useful. Any help is greatly appreciated.

  Read the article

• SQL 2008 SP1 crashing almost daily

  - by matijake

  Hey, almost every day our new DB crashes. It is virtual server residing on same hardware as 5 other servers, two of them beeing identical MS SQL2008sp1 and two Oracle 11g's so I can pretty much rule out hardware issues. Server has dedicated local LUN, 4vCPU and 8GB memory with 2GB windows swap file. It runs 4 instances. Primary instance is limited to 5GB memory and paralelism set to 4 running on MS SQL 2008 SP1 @ Windows Server 2008 Enterprise R2 x64. Only that primary instance is crashing. After it crashes nothing can connect to it, it's even impossible to shut it down through service manager. What I found in logs is: ***Stack Dump being sent to C:\Program Files\Microsoft SQL Server\MSSQL10.MSSQLSERVER\MSSQL\LOG\SQLDump0081.txt SqlDumpExceptionHandler: Process 4788 generated fatal exception c0000005 EXCEPTION_ACCESS_VIOLATION. SQL Server i s terminating this process.     Whole log can be seen at: http://kabl.org/files/SQLDump0081.txt second crash log made second later at: http://kabl.org/files/SQLDump0082.txt I have analyzed mini crashdump with Microsoft tools, but no promising results. If it can help, here it is: http://kabl.org/files/SQLDump0081.mdmp Any ideas are greatly welcome, since it is becoming quite a pain in the ass to restart server almost every day :) Regrads, -Matija

  Read the article

• Network Misconfiguration when adding first host to new vSphere cluster

  - by dunxd

  I am building a new vSphere cluster from scratch. I have installed ESXi on the first host, and built a vCenter server on a VM residing on that host (storage is on the local hard drive, although we have iSCSI targets which I can reach from the host). The cluster is configured for HA. When I try and add the host to the cluster, I get an error at the point where HA is configured - Cannot complete the . I have stripped the network configuration of the host down to the most basic - a single NIC attached to a single vSwitch - this is running the VMKernel Port on VLAN 8 - that is our Management VLAN. The vCenter server will have a network address on this VLAN, so I also set the initial Virtual Machine Port Group to this VLAN, and connected the vCenter server NIC to this port group. I understand I can't connect the vCenter server to the VMkernel port group, but shouldn't I be able to connect the vCenter server to a Port Group in the same VLAN? If not, do I need to create a VLAN specifically for VMKernel Port Group? I plan to set up another port group for vMotion with a dedicated and isolated VLAN (i.e. VLAN isn't routed) so this wouldn't allow vCenter to communicate. Does anyone have any suggestions, or other ideas for what might be causing the problem. I've read through the documentation, but it isn't giving me any pointers, and the error message isn't helping me beyond telling me something is wrong with my network config.

  Read the article

• Representing server state with a metric

  - by Sal

  I'm using Microsoft's Performance Monitor to dump logs of RAM, CPU, network, and disk usage from multiple servers. I'd like to get a single metric that captures the state of a given variable to a good extent. For instance, disk usage is pretty stable, so if I take a single reading that says I have 50% remaining disk space, that reading will give me an accurate measure for the day. (The servers aren't doing heavy IO writing.) However, the tricky part here is monitoring CPU and network usage. The logs currently dump the % CPU usage every ten seconds. If I take a straight average of the numbers, it may not represent reality, as % CPU will be much lower during the night than day. (We host websites that sell appliance items.) I'd like to get an average over a span during peak hours (about 5 hours in the day) and present a daily peak hour metric. Of course, there are most likely some readings that will come in as overly spiked (if multiple users pinged the server at once) or no use (a momentary idle state). Is there a standard distribution/test industries use in these situation?

  Read the article

• Forwarding HTTP Request with Direct Server Return

  - by Daniel Crabtree

  I have servers spread across several data centers, each storing different files. I want users to be able to access the files on all servers through a single domain and have the individual servers return the files directly to the users. The following shows a simple example: 1) The user's browser requests http://www.example.com/files/file1.zip 2) Request goes to server A, based on the DNS A record for example.com. 3) Server A analyzes the request and works out that /files/file1.zip is stored on server B. 4) Server A forwards the request to server B. 5) Server B returns file1.zip directly to the user without going through server A. Note: steps 4 and 5 must be transparent to the user and cannot involve sending a redirect to the user as that would violate the requirement of a single domain. From my research, what I want to achieve is called "Direct Server Return" and it is a common setup for load balancing. It is also sometimes called a half reverse proxy. For step 4, it sounds like I need to do MAC Address Translation and then pass the request back onto the network and for servers outside the network of server A tunneling will be required. For step 5, I simply need to configure server B, as per the real servers in a load balancing setup. Namely, server B should have server A's IP address on the loopback interface and it should not answer any ARP requests for that IP address. My problem is how to actually achieve step 4? I have found plenty of hardware and software that can do this for simple load balancing at layer 4, but these solutions fall short and cannot handle the kind of custom routing I require. It seems like I will need to roll my own solution. Ideally, I would like to do the routing / forwarding at the web server level, i.e. in PHP or C# / ASP.net. However, I am open to doing it at a lower level such as Apache or IIS, or at an even lower level, i.e. a custom proxy service in front of everything. Thanks.

  Read the article

• Poor SSL performance with vsftpd

  - by petrus

  I'm trying to tweak vsftpd to achieve maximum performance for my usage: I have only one or two clients that connect to the server. File size is between ~15MB and 1GB. Typical transfer batch represent between 1 and 2GB of data. For testing purposes, I'm using a tmpfs on both sides (thus eliminating any disks bottleneck) with a single 1GB file. When SSL is disabled, performance is good, with a transfer rate at ~120MB/s (reaching the limits of gigabit networking). With SSL enabled only for control traffic (and not data traffic), performance drops at about 112MB/s, which is still within the acceptable limits. However, when SSL is enabled for data flows, the transfer speed drops dramatically: 6.7MB/s using 3DES & SHA (ssl_ciphers=DES-CBC3-SHA in vsftpd.conf) 16MB/s using DES & SHA (ssl_ciphers=DES-CBC-SHA) I didn't tested other ciphers, but from what I can see from the CPU usage during the transfer, it seems that vsftpd is only using a single cpu/core per client. While this can fit for large ftp sites with hundreds of clients, I'd like to avoid this behavior and use more ressources on the server. On a side note, if you have any ideas regarding other openssl ciphers...

  Read the article

• How would I setup iMail to forward a user's mail to another service w/o leaving a copy locally?

  - by Scott Mayfield

  I have an iMail 2006 server installation in which I have a particular user that has several aliases that all point to a single user (me, for the record). I've been copying all of my mail to GMail and reading it there, but it annoys me that I have to go back weekly and log into my mail account on iMail and delete between 6 and 10 thousand copies of messages I've already received, in order to keep my mailbox from filling up (yes, I have it set with no quota, but I consider it bad form to just let the box grow indefinitely). I've got the copying setup via an inbound user rule, but I'm wondering how to accomplish a "copy and delete" rule. The manual isn't clear on what happens with multiple matching rules (will they be processed in order, or is it a first match situation?) and there isn't a means to combine multiple actions into a single rule. If I use the "forward" action, I THINK that it's going to screw up all the sender information once the mail reaches my GMail account and show it as coming from me instead of the original senders (can anyone confirm that this is accurate?) An easy answer would be to delete my user account entirely, replace it with an alias that maps to my GMail account, but then I would lose my ability to log into the system for admin duties. So that leads me to creating a second, lesser known account for admin use, but since it's a real account, sooner or later I'm going to get mail sent to it and I'll be back to the same situation of having a user account that doesn't get emptied periodically. I imagine I can set the quota to 0 MB to cause all incoming mail to my admin account to bounce, or setup an inbound rule to bounce everything, but this is starting to sound kludgy to me. Does anyone know of a more direct work around to copying a user's incoming mail to an outside server and then deleting the local copy w/o removing their account entirely? Or is this just wishful thinking? Thanks in advance. Scott

  Read the article

• Slow disk transfer rate

  - by Nooklez

  I have problem with slow disk transfer rate. It's static files server for our website. I was making backup of data and noticed that tar is very slow. So I did hdparm -t and... hdparm -t /dev/sda3 /dev/sda3: Timing buffered disk reads: 6 MB in 4.70 seconds = 1.28 MB/sec It's low traffic hour now on our site, so huge I/O traffic is not a reason (iotop show less than 1 MB/s). It's RAID10 setup (2x2 SATA drives). Unit UnitType Status %RCmpl %V/I/M Stripe Size(GB) Cache AVrfy ------------------------------------------------------------------------------ u0 RAID-10 OK - - 64K 1396.96 W ON VPort Status Unit Size Type Phy Encl-Slot Model ------------------------------------------------------------------------------ p0 OK u0 698.63 GB SATA 0 - WDC WD7500AADS-00M2 p1 OK u0 698.63 GB SATA 1 - WDC WD7500AADS-00M2 p2 OK u0 698.63 GB SATA 2 - WDC WD7500AADS-00M2 p3 OK u0 698.63 GB SATA 3 - WDC WD7500AADS-00M2 We have recently changed almost all components of server (excluding 3ware controller + disks). And I think problems started since then. Can it be configuration problem or hardware? EDIT: I found something like that in dmesg [166843.625843] irq 16: nobody cared (try booting with the "irqpoll" option) [166843.625846] Pid: 0, comm: swapper Not tainted 3.1.5-gentoo #3 [166843.625847] Call Trace: [166843.625848] <IRQ> [<ffffffff810859d5>] __report_bad_irq+0x35/0xc1 [166843.625856] [<ffffffff81085cec>] note_interrupt+0x165/0x1e1 [166843.625859] [<ffffffff8108445f>] handle_irq_event_percpu+0x16f/0x187 [166843.625861] [<ffffffff810844a9>] handle_irq_event+0x32/0x51 [166843.625863] [<ffffffff8108640b>] handle_fasteoi_irq+0x75/0x99 [166843.625866] [<ffffffff810039d7>] handle_irq+0x83/0x8b [166843.625868] [<ffffffff810036ad>] do_IRQ+0x48/0xa0 [166843.625871] [<ffffffff8155082b>] common_interrupt+0x6b/0x6b [166843.625872] <EOI> [<ffffffff812981e8>] ? acpi_safe_halt+0x22/0x35 [166843.625877] [<ffffffff812981e2>] ? acpi_safe_halt+0x1c/0x35 [166843.625879] [<ffffffff81298216>] acpi_idle_do_entry+0x1b/0x2b [166843.625881] [<ffffffff81298276>] acpi_idle_enter_c1+0x50/0x99 [166843.625884] [<ffffffff813b792a>] cpuidle_idle_call+0xed/0x171 [166843.625886] [<ffffffff81001257>] cpu_idle+0x55/0x81 [166843.625888] [<ffffffff81532a69>] rest_init+0x6d/0x6f [166843.625891] [<ffffffff81aa1aca>] start_kernel+0x329/0x334 [166843.625893] [<ffffffff81aa12a6>] x86_64_start_reservations+0xb6/0xba [166843.625894] [<ffffffff81aa139c>] x86_64_start_kernel+0xf2/0xf9 [166843.625896] handlers: [166843.625898] [<ffffffff812dc8de>] twl_interrupt [166843.625900] Disabling IRQ #16 It's related to problem? EDIT #2: Based on feedback in comments, here is more informations. cat /proc/interrupts 16: 390813 0 0 0 IO-APIC-fasteoi 3w-sas Controller model: [ 1.095350] 3ware Storage Controller device driver for Linux v1.26.02.003. [ 1.095467] 3ware 9000 Storage Controller device driver for Linux v2.26.02.014. [ 1.095641] LSI 3ware SAS/SATA-RAID Controller device driver for Linux v3.26.02.000. [ 1.095787] 3w-sas 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 1.095881] 3w-sas 0000:01:00.0: setting latency timer to 64 [ 1.910801] 3w-sas: scsi0: Found an LSI 3ware 9750-4i Controller at 0xfe560000, IRQ: 16. [ 2.216537] 3w-sas: scsi0: Firmware FH9X 5.08.00.008, BIOS BE9X 5.07.00.011, Phys: 8. [ 2.216836] scsi 0:0:0:0: Direct-Access LSI 9750-4i DISK 5.08 PQ: 0 ANSI: 5 And motherboard: description: Motherboard product: P8H67-M vendor: ASUSTeK Computer INC.

  Read the article

• Ping server NETBIOS name returns wrong IP and "Destination host unreachable"

  - by music2myear

  Problem server is Windows 2008 R2 VM running on VMWare ESXi 4 host. Single network adapter manually assigned single IP address (192.168.1.11). When I ping the server from any other network computer, it returns 192.168.1.124 and "Destination host unreachable". Yesterday I found a second network adapter assigned to this server with an IP of 169.254... indicating it had no real valid IP. Using the MAC addresses I determined which adapter was not needed/not wanted, and removed it using VMWare systems. This is the network Printer Server and, understandably, nothing is printing right now. I've looked at the solutions here Why was my ping answered by a different IP address than the one pinged? and they aren't applicable to my situation for the following reasons: Output of arp -a on another computer returns the correct IP address (.1.11) assigned to the correct MAC address, the incorrect IP .1.124 is not listed, and the MAC of the network adapter I removed yesterday is not listed at all. I checked out the Microsoft KB article which listed pretty much my exact symptoms ( http://support.microsoft.com/kb/981953 ) and it says to check binding orders and look for hidden adapters. But there are no hidden adapters, and there is only one Network Adapter listed in the Binding Order list. Essentially, I can communicate from the server TO any other network device, but I cannot communicate from any other network device TO the server. Help! UPDATE: Solution found, see this solution for the details.

  Read the article

• SQL Query to update parent record with child record values

  - by Wells

  I need to create a Trigger that fires when a child record (Codes) is added, updated or deleted. The Trigger stuffs a string of comma separated Code values from all child records (Codes) into a single field in the parent record (Projects) of the added, updated or deleted child record. I am stuck on writing a correct query to retrieve the Code values from just those child records that are the children of a single parent record. -- Create the test tables CREATE TABLE projects ( ProjectId varchar(16) PRIMARY KEY, ProjectName varchar(100), Codestring nvarchar(100) ) GO CREATE TABLE prcodes ( CodeId varchar(16) PRIMARY KEY, Code varchar (4), ProjectId varchar(16) ) GO -- Add sample data to tables: Two projects records, one with 3 child records, the other with 2. INSERT INTO projects (ProjectId, ProjectName) SELECT '101','Smith' UNION ALL SELECT '102','Jones' GO INSERT INTO prcodes (CodeId, Code, ProjectId) SELECT 'A1','Blue', '101' UNION ALL SELECT 'A2','Pink', '101' UNION ALL SELECT 'A3','Gray', '101' UNION ALL SELECT 'A4','Blue', '102' UNION ALL SELECT 'A5','Gray', '102' GO I am stuck on how to create a correct Update query. Can you help fix this query? -- Partially working, but stuffs all values, not just values from chile (prcodes) records of parent (projects) UPDATE proj SET proj.Codestring = (SELECT STUFF((SELECT ',' + prc.Code FROM projects proj INNER JOIN prcodes prc ON proj.ProjectId = prc.ProjectId ORDER BY 1 ASC FOR XML PATH('')),1, 1, '')) The result I get for the Codestring field in Projects is: ProjectId ProjectName Codestring 101 Smith Blue,Blue,Gray,Gray,Pink ... But the result I need for the Codestring field in Projects is: ProjectId ProjectName Codestring 101 Smith Blue,Pink,Gray ... Here is my start on the Trigger. The Update query, above, will be added to this Trigger. Can you help me complete the Trigger creation query? CREATE TRIGGER Update_Codestring ON prcodes AFTER INSERT, UPDATE, DELETE AS WITH CTE AS ( select ProjectId from inserted union select ProjectId from deleted )

  Read the article

• Performance of Cluster Shared Volume file copy from SAN

  - by Sequenzia

  I am hoping someone can help me out with a strange issue. We are running a Microsoft Failover Cluster with Server 2008 R2 and an Equallogic PS4000 SAN. Our main configuration has 2 Dell Poweredge T710 Servers in the cluster. We have CSV and Quorm setup. The servers each have 10 Broadcom 1Gb NICs. Right now 4 of the NICS are on the iSCSI network for accessing the SAN. They use MPIO and the Dell HIT pack. We have 5 VMs running on each node and everything runs smooth. No noticeable performance issues or anything. From the SAN I can see the 4 iSCSI connections from each server to each volume (CSV and Quorm). Again, it seems to perform great. The problem I am running into is with backups. I have tried a few backup programs like backupchain and Veeam. The problem is both of them are very very slow to backup the VMs. For instance I have a 500GB (fixed disc) VHD that’s running on the cluster. It takes over 18 hours to backup that VHD and that’s with compression and depuping turned off which is supposed to be the fasted. We also have a separate server that is just for backups. It has a lot of directed attached storage. As part of the troubleshooting I decided to bring that server into the cluster as a node. It now has access to the CSV and can read from C:\clusterstorage\volume1 which is where our VHDs live. This backup server only has 2 NICs. 1 NIC is going to the iSCSI network and the other is just on the main network. It has Intel NICS in it without any sort of MPIO or teaming. So with the 3rd server now in the cluster I started doing some benchmarking. I have a test VHD that’s about 7GBs that’s stored in the CSV. I have tested file copying that VHD from all 3 servers to directed attached storage in the respective server. The 2 Dell servers that are the main nodes in the cluster (they house the VMs) are reading that file at about 20Mbs/Sec. Which at that rate is way to slow for the backups. The other server which only has 1 NIC to the SAN is reading at around 100Mbs/Sec. I spent a few hours on the phone with Dell today about this . We went through all kind of tests and he was pretty dumb founded. He really has no idea why that server with only 1 NIC is reading about 5 times as fast as the servers with 4 NICS and MPIO. We looked at the network utilization of the NICs while the file copy was going on. The servers with the 4 NICs had a small increase of activity during the file copy but they only went up to around 8-10% on all 4 NICs. The other server with the 1 NIC jumped up to over 80% during the file copy. I plan on doing some more testing after hours and calling Dell back tomorrow but I really am confused (and so is Dell’s support rep) why I cannot get faster file copy access to the CSV on those servers. Anyone have any input on this? Any feedback would be greatly appreciated. Thanks in advance.

  Read the article

• Why would Windows Task Scheduler spawn multiple instances of the same task that run into each other?

  - by swagner88

  Overview: I use Windows Task Scheduler to run automated tasks. Occasionally I will see that randomly a task has failed to perform its duties. When I check Task Scheduler to see what has occurred in the history log, I see that for some reason, when the tasks are triggered at their schedules, they are spawning several instances of themselves simultaneously which turns into a train wreck for the task and it either kills the other instances and tries to run the "first" one, or it just does not run at all as it believes another instance of itself is already running. Sometimes this occurs in the same tasks and then occasionally it happens with others. The fix is just to end all instances and start the task manually. Question: Why would one single task with one single schedule decide to spawn multiple instance of itself simultaneously? Note: I've got a separate user account set to run the tasks instead of myself. That user is indeed an admin on the machine that runs the tasks and the tasks are set to tun whether or not the user is logged on. Also, the machine is windows server 08 R2.

  Read the article

• MySQL Server hitting 100% unexpectedly (Amazon AWS RDS)

  - by Luc

  Please help! We've been struggling with this one for months. This week we upped our RDS instance to the highest performing instance and although the occurrences have reduced, we're still having our DB all of a sudden hit 100%. It comes out of nowhere. Sometimes 2am, sometimes midday. I've ruled out a DOS - our pages access logs have normal traffic I've ruled out memcached suddenly dieing (hits and misses continue as normal). The SHOW PROCESSLIST while we have issues reports about 500 queries in queue. If I kill them off or restart the server, they just keep coming back and then eventually out of knowhere, our server resumes back to normal. Sometimes up to 3 hours. Our bad performing queries take .02 seconds to execute when the server eventually returns back to normal but while we're in this 100% CPU physco phase, those queries never finish executing. Please help!!!!! Anybody know anything about MYSQL query optimization? Could it be the server deciding to use different indexes all of a sudden, which puts it into a spiral?

  Read the article

• Automate creation of Windows startup script?

  - by Niten

  Is there a good way to automate installing local startup (rather than login) scripts in Windows XP and Windows 7, via the command line, WMI, or otherwise (even COM or Win32 if it comes to that)? I need to setup a local startup script on a large number of computers, and unfortunately, Active Directory is absolutely not an option. I would like to write a script or small program that I can run on each computer to perform the startup script installation in order to save myself a lot of error-prone point-and-click manual labor. I see that when one uses gpedit.msc to create a local startup script, information about the script gets stored in the registry here: HKLM\Software\Policies\Microsoft\Windows\System\Scripts\Startup However, if you create such a script and then delete its registry key, the script will remain listed in the local Group Policy editor; as is so often the case in Windows, apparently there is more going on there than meets the eye. This leads me to question whether it's safe to manually add subkeys for new startup scripts here (I wouldn't want my script to be overwritten by later changes made using the local Group Policy editor, for instance)... Another option that's occurred to me is to create an item in the Task Scheduler configured to run at system startup. However, my concerns there are twofold: Can this be automated any more easily? For instance, the at command doesn't appear to let you schedule a task for system startup, and WMI's Win32_ScheduledJob interface looks unreliable (it fails to show any of my currently scheduled tasks, for one thing). Would I be able to prevent users from logging in until the scheduled startup task is completed, as can be done with "normal" Windows startup scripts? Thanks in advance for any suggestions, I've been banging my head against this one for a bit...

  Read the article

• How to use Timer broadcast on Multi-Processor system with linux 3.10?

  - by kevin.ji

  Hardware: ARM Cortex-A9 * 2 Software: linux-3.10.0 The platform has 2 cores of arm cortex-a9. Item CONFIG_LOCAL_TIMERS is not set in linux menuconfig. I want to use only one hardware timer to supply tick for all cpu. Interrupts looks like: CPU0 CPU1 57: 6697 0 GIC timer 81: 213 0 GIC uart-pl011 103: 0 0 GIC gmac0 104: 0 0 GIC gmac1 IPI0: 0 1 CPU wakeup interrupts IPI1: 0 0 Timer broadcast interrupts IPI2: 967 866 Rescheduling interrupts IPI3: 0 0 Function call interrupts IPI4: 1 2 Single function call interrupts IPI5: 0 0 CPU stop interrupts IPI6: 0 0 CPU backtrace Err: 0 Timer broadcast interrupts counter does not add. And it looks like that cpu1 does not work at all.But this method works well with linux-3.4, and the interrupt info looks as below in linux-3.4: # cat /proc/interrupts CPU0 CPU1 57: 8596 0 GIC timer 81: 91 0 GIC uart-pl011 103: 0 0 GIC gmac0 104: 0 0 GIC gmac1 IPI0: 0 8560 Timer broadcast interrupts IPI1: 884 1020 Rescheduling interrupts IPI2: 0 0 Function call interrupts IPI3: 0 6 Single function call interrupts IPI4: 0 0 CPU stop interrupts IPI5: 0 0 CPU backtrace Err: 0 The count of Timer broadcast interrupts is adding. And all of cpus work well. I don't know why. Any answer is welcome. :)

  Read the article

• LDAP, Active Directory and bears, oh my!

  - by Tim Post

  What I have: Workstations running Ubuntu Jaunty mounting /home on a remote NFS server. User accounts are still created locally on each individual workstation. Workstations running Windows XP / Vista NFS server (as noted above) Windows 2008 server All machines share a single private network (LAN). What I need to accomplish: A single, intuitive (GUI driven) place for an office administrator to create user accounts. This should let anyone login to their (linux or windows) workstation, then fire up remote desktop and use the same login to the Windows 2008 server, from any machine on the network. I have read so much on samba, LDAP vs AD, etc and now I'm even more confused than I was before I began researching the problem. Ideally, Linux and Windows users should be able to get to their local files once logged into the Win2008 server. I am a programmer, not an interoperability guru and I'm completely lost on where to even start trying to accomplish this, plus I've run out of things to Google. How would you do this? Is it even possible?

  Read the article

• Certain Japanese characters aren't displayed properly

  - by Nisto

  On the following site: http://www.nciku.com/search/radical the first 2 characters on the second row of the "Step 2" table aren't displayed properly. All other characters look fine. I tried re-installing the Asian fonts via the checkboxes regarding Asian fonts in the "Regional and Language Options" control panel applet. I have tried removing every single Font from the Fonts folder (some were ofcourse not possible to remove), and re-installing them all again. I did this by... Running cmd Closing down the explorer process In cmd; using the command DEL /F /S /Q * in the Fonts folder Putting in my XP SP3 Retail disc In cmd; using expand -r *.tt_ in the I386 folder on the XP disc (and any other font file, in the I386\LANG folder) I also tried installing this pack from Microsoft, but this solved nothing either. I even tried running my browser (Firefox) through AppLocale. And changing character encoding -- again, does not help. I've also tried viewing the page in Internet Explorer. What could be wrong? I have checked my Fonts folder, to make sure that every single font available on the XP disc is available in WINDOWS\Fonts. What shows in the first square on the second row - I can't really tell what it's supposed to look like (but it's not the proper character)... but the second square shows a rectangular symbol containing HEX code. I've been in this situation before -- and it has been when I've been missing fonts. But how could I possibly be missing a necessary font? Shouldn't it be provided in the Asian "font packages"? I've talked to some other users that has viewed the page, and they had no problems displaying those characters on second row - even though they're only using the fonts provided on the Windows installation disc. Windows XP Professional Service Pack 3 (x86 - with latest updates) Firefox 3.6.15

  Read the article

< Previous Page | 404 405 406 407 408 409 410 411 412 413 414 415  | Next Page >