Search Results

Search found 27819 results on 1113 pages for 'linux intel'.

Page 409/1113 | < Previous Page | 405 406 407 408 409 410 411 412 413 414 415 416  | Next Page >

  • Causes of sudden massive filesystem damage? ("root inode is not a directory")

    - by poolie
    I have a laptop running Maverick (very happily until yesterday), with a Patriot Torx SSD; LUKS encryption of the whole partition; one lvm physical volume on top of that; then home and root in ext4 logical volumes on top of that. When I tried to boot it yesterday, it complained that it couldn't mount the root filesystem. Running fsck, basically every inode seems to be wrong. Both home and root filesystems show similar problems. Checking a backup superblock doesn't help. e2fsck 1.41.12 (17-May-2010) lithe_root was not cleanly unmounted, check forced. Resize inode not valid. Recreate? no Pass 1: Checking inodes, blocks, and sizes Root inode is not a directory. Clear? no Root inode has dtime set (probably due to old mke2fs). Fix? no Inode 2 is in use, but has dtime set. Fix? no Inode 2 has a extra size (4730) which is invalid Fix? no Inode 2 has compression flag set on filesystem without compression support. Clear? no Inode 2 has INDEX_FL flag set but is not a directory. Clear HTree index? no HTREE directory inode 2 has an invalid root node. Clear HTree index? no Inode 2, i_size is 9581392125871137995, should be 0. Fix? no Inode 2, i_blocks is 40456527802719, should be 0. Fix? no Reserved inode 3 (<The ACL index inode>) has invalid mode. Clear? no Inode 3 has compression flag set on filesystem without compression support. Clear? no Inode 3 has INDEX_FL flag set but is not a directory. Clear HTree index? no .... Running strings across the filesystems, I can see there are what look like filenames and user data there. I do have sufficiently good backups (touch wood) that it's not worth grovelling around to pull back individual files, though I might save an image of the unencrypted disk before I rebuild, just in case. smartctl doesn't show any errors, neither does the kernel log. Running a write-mode badblocks across the swap lv doesn't find problems either. So the disk may be failing, but not in an obvious way. At this point I'm basically, as they say, fscked? Back to reinstalling, perhaps running badblocks over the disk, then restoring from backup? There doesn't even seem to be enough data to file a meaningful bug... I don't recall that this machine crashed last time I used it. At this point I suspect a bug or memory corruption caused it to write garbage across the disks when it was last running, or some kind of subtle failure mode for the SSD. What do you think would have caused this? Is there anything else you'd try?

    Read the article

  • freeradius maximum session time problem

    - by haw3d
    hello I'm using openvpn and free-radius for control user accounts. for maximum session time for an user, free-radius has sqlcounter.conf that control that, but after a connection has disconnected that is useful and cannot destroy a connection. for control account time dynamically i need another script that do that. but should anytime that a connection has established a trigger run. is anyway to fire a custom trigger or script when a connection has established? or any way to control session time dynamically?

    Read the article

  • Problem about IP and computer name in Ubuntu

    - by bugbug
    I can't connect to mysql database becase it alway change 192.168.1.101 to ubuntu.local. $ mysql -uroot -padmin1234 -h192.168.1.101 ERROR 1045 (28000) : Access denined for user 'root'@'ubuntu.local' (using password: YES) How do I solve this problem. File: /etc/hosts in this machine 127.0.0.1 localhost 127.0.1.1 ubuntu.ubuntu-domain ubuntu # The following lines are desirable for IPv6 capable hosts ::1 localhost ip6-localhost ip6-loopback fe00::0 ip6-localnet ff00::0 ip6-mcastprefix ff02::1 ip6-allnodes ff02::2 ip6-allrouters ff02::3 ip6-allhosts I have no idea about "root'@'ubuntu.local", where is it come from.

    Read the article

  • How to stop syslog from listening to 514 on CentOS 5.8

    - by Jim
    I have a CentOS 5.8 machine (with regular syslog) that for some reason is listening to port 514, even though it is not started with "-r" (to receive remote syslog messages). # netstat -tulpn | grep 514 udp 0 0 0.0.0.0:514 0.0.0.0:* 2698/syslogd Syslog is started with only "-m 0": ps -ef | grep syslogd root 2698 1 0 15:55 ? 00:00:00 syslogd -m 0 I have tried starting it with "-m 0 -r", just to check if there was any difference, but there is not. This machine is a client and should only log to a central log server - it should not be listening itself. What am I missing?

    Read the article

  • Permissions nightmare - tried all I know

    - by Ben
    Working on a new client's dev site, which is a wordpress install on a Plesk box. I have SSH root access, and FTP access through a separate account. What I've done so far Initially I couldn't make any changes to any files at all. The permissions on all the template files looked a little screwy (644), so I figured change them to allow group, and add myself to the group: CHMOD Recursive on the theme folder to set everything to 664 Quickly realised I'd broken it, set the folders to 755, kept files as 664 Ownership on all files is a mixture of root:root and 500:500 (there is no user nor group with the ID of 500 on the server). Added myself to the group 'root' so I could modify the files too The Problem This worked OK, in terms of being able to edit the existing files, so I began working. However, I can't upload to the directory, even having run CHOWN -R root:root templatefolder/ and being in the root group. I feel like I must be missing something obvious, and it's doing my head in. Questions: Files in the install owned by 500 with group 500 - I've looked in /etc/group and /etc/passwd and there is no user nor group with this ID. Is that left over from another developer's setup or the previous server (they moved recently)? Is being in the 'root' group enough, or do I need to own the theme folder as 'myftpuser' in order to upload and create new files? Like I say, I have edit access, so I got myself this far. I'm now questioning what to do next!

    Read the article

  • Ubuntu won't boot from USB memory stick

    - by mackenir
    I used the instructions on this webpage to create a bootable USB drive for running Ubuntu 9.10. Unfortunately it doesn't work on my EeePC. Even with 'Removable Dev.' selected in the BIOS as the first boot device, the PC just boots into Windows 7. How do I troubleshoot this problem? The drive is readable and looks like this: Directory of E:\ 28/10/2009 21:14 <DIR> .disk 28/10/2009 21:14 222 README.diskdefines 28/10/2009 21:14 143 autorun.inf 28/10/2009 21:14 <DIR> casper 28/10/2009 21:14 <DIR> dists 28/10/2009 21:14 <DIR> install 28/10/2009 21:14 <DIR> syslinux 28/10/2009 21:14 4,098 md5sum.txt 28/10/2009 21:14 <DIR> pics 28/10/2009 21:14 <DIR> pool 28/10/2009 21:14 <DIR> preseed 28/10/2009 21:14 0 ubuntu 26/10/2009 16:16 1,468,640 wubi.exe 25/02/2010 00:28 2,147,483,648 casper-rw 8 Dir(s) 5,290,307,584 bytes free

    Read the article

  • UAE and the mysteries of unreachable websites

    - by 0plus1
    I write here because I'm really lost, please stay with me because it's not easy to explain. A company asked me to set-up a private server, now I'm a programmer so I got a solution with technical support and cpanel which helped me to setup everything and it's working smoothless. I'm by no means a professional sysadmin, but I have a fair knowledge of server configurations, but this problem is way over my knowledge, and apparently way over the knowledge of most sysadmins, I really hope that here I'll find someone with enough experience to help me or at least give me more insight. Now this company for which I'm consulting operates in the UAE (United Arab Emirates) and from there the server is almost unreachable. It started with ns not registering in the UAE, after a week that sorted itself out and now the site is indeed reachable, but it takes almost 2 minutes to load a webpage with one line of text. Emails go in timeout. The domain currently parked there has been bought appositely for tests, the main one that was supposed to go there, after a catastrophic week has been transferred to a shared hosting solution in the UK, and from there it works like a charme. Now after doing some research I discovered that I'm not alone in this, there are several reports of webmasters discovering that their website is not reachable inside the UAE, and mind this has nothing to do with the state-wide block of questionable sites, because in that case an error message appears, this seems to be related to the infrastructure of the UAE, which apparently reroutes everything through their own "fake" internet. Apparently new servers with their own IP are not recognized (yet?) by the UAE infrastructure, while shared hosting solutions seeing that they operates tons of other websites are more likely to be part of the UAE network. Now my questions are: 1) Has someone a real explanation for this? The only thing I can think of is that the server is on a new IP that is not yet recognized by the UAE, but that doesn't explain why it loads (even if after 2 minutes). I don't have any help from within the UAE as the only people that are "experts" are questionable companies that simply try to sell their own services. 2) If there is really some kind of block of new servers, is it possible to know before if a server is reachable from within the UAE, currently this is not a ns problem as even accessing the server with its IP result in a 2 minute wait. 3) Can it be that the problem lies somewhere else? There are some tests that I can perform? I'm not physically in the UAE, but I can ask the people there, or use teamviewer. Could it be some misconfiguration on the server (mind that the site works EVERYWHERE else in the world). Thank you for ANY kind of help

    Read the article

  • How do I reference the value of a constructed environment variable in a loop?

    - by Rob Spieldenner
    What I'm trying to do is loop over environment variables. I have a number of installs that change and each install has 3 IPs to push files to and run scripts on, and I want to automate this as much as possible (so that I only have to modify a file that I'll source with the environment variables). The following is a simplified version that once I figure out I can solve my problem. So given in my.props: COUNT=2 A_0=foo B_0=bar A_1=fizz B_1=buzz I want to fill in the for loop in the following script #!/bin/bash . <path>/my.props for ((i=0; i < COUNT; i++)) do <script here> done So that I can get the values from the environment variables. Like the following(but that actually work): echo $A_$i $B_$i or A=A_$i B=B_$i echo $A $B returns foo bar then fizz buzz

    Read the article

  • Amazon EC2 tools for Debian?

    - by Jonik
    What is the recommended way of getting command-line Amazon EC2 tools on Debian? So, basically the same as this question, but for EC2 instead of S3. Ubuntu has ec2-ami-tools and ec2-api-tools, but I couldn't find equivalent packages for Debian. A blog post titled "Install EC2 AMI & API tools in Debian" talks about installing Amazon's packages outside package management, but that seems a little clumsy.

    Read the article

  • Unattended Kickstart Install

    - by Eric
    I've looked around quite a bit and have seen similar setup and questions, but none seem to work for me. I'm using the following command to create a custom ISO: /usr/bin/livecd-creator --config=/usr/share/livecd-tools/test.ks --fslabel=TestAppliance --cache=/var/cache/live This works great and it creates the ISO with all of the packages and configs I want on it. My issue is that I want the install to be unattended. However, every time I start the CD, it asks for all of the info such as keyboard, time zone, root password, etc. These are my basic settings I have in my kickstart script prior to the packages section. cdrom install autopart autostep xconfig --startxonboot rootpw testpassword lang en_US.UTF-8 keyboard us timezone --utc America/New_York auth --useshadow --enablemd5 selinux --disabled services --enabled=iptables,rsyslog,sshd,ntpd,NetworkManager,network --disabled=sendmail,cups,firstboot,ip6tables clearpart --all So after looking around, I was told that I need to modify my isolinux.cfg file to either do "ks=http://X.X.X.X/location/to/test.ks" or "ks=cdrom:/test.ks". I've tried both methods and it still forces me to go through the install process. When I tail the apache logs on the server, I see that the ISO never even tries to get the file. Below are the exact syntax I'm trying on my isolinux.cfg file. label http menu label HTTP kernel vmlinuz0 append initrd=initrd0.img ks=http://192.168.56.101/files/test.ks ksdevice=eth0 label localks menu label LocalKS kernel vmlinuz0 append initrd=initrd0.img ks=cdrom:/test.ks label install0 menu label Install kernel vmlinuz0 append initrd=initrd0.img root=live:CDLABEL=PerimeterAppliance rootfstype=auto ro liveimg liveinst noswap rd_NO_LUKS rd_NO_MD rd_NO_DM menu default EOF_boot_menu The first 2 give me a "dracut: fatal: no or empty root=" error until I give it a root= option and then it just skips the kickstart completely. The last one is my default option that works fine, but just requires a lot of user input. Any help would be greatly appreciated.

    Read the article

  • How to run KDM or GDM over ssh

    - by Xolve
    I have a computer on LAN running ssh. I can normally tunnel the GUI application using ssh computer-name -X program-name But I wam my full desktop to be running on a remote computer using ssh so that I can just use that computer remotely like a local desktop. For this I think I will need to run KDM (or GDM ) remotely, what configuration do I need to do to make this happen?

    Read the article

  • PacketFence Installation?

    - by Charles Miton
    So I've stumbled across PacketFence during my search for a decent Network Access Control system. After doing a little research about it's capabilities I've come to realize it's meets all the requirements that I was looking for. Unfortunately, being primarily a MS Administrator, I'm having many issues trying to successfully getting it up and running. Is there anyone or any place that has a step-by-step tutorial on how to do this? I love the prospect of using Open Source software, but need some help jumping this particular hurdle. I'm trying to use CentOS for the OS but I'm open to alternatives if thats what it takes to get this system up and running.

    Read the article

  • IPv6 Routing / Subnetting

    - by nappo
    Recently I have installed Citrix Xen Server 6.2 on a machine. My Provider (Hetzner) gave me the IPv6 Subnet 2a01:4f8:200:xxxx::/64. Followed an article in the providers wiki (1) i got it working and can assign IPs to my guests (CentOS). However i can't assign a second IP to a single guest - it will result in a timeout. I'm not very familiar with IPv6 routing / subnetting - any help or tips for further troubleshooting is welcome! My Setup: XenServer 6.2 IPv6: 2a01:4f8:200:xxxx::2/112 ip -6 route: 2a01:4f8:200:xxxx::/112 dev xenbr0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 0 fe80::1 dev xenbr0 metric 1024 mtu 1500 advmss 1440 hoplimit 0 default via fe80::1 dev xenbr0 metric 1024 mtu 1500 advmss 1440 hoplimit 0 Guest 1 IPv6: 2a01:4f8:200:xxxx::3/64 IPv6: 2a01:4f8:200:xxxx::4/64 ip -6 route: 2a01:4f8:200:xxxx::/64 dev eth0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 fe80::/64 dev eth0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 default via fe80::1 dev eth0 metric 1 mtu 1500 advmss 1440 hoplimit 4294967295 Guest 2 IPv6: 2a01:4f8:200:xxxx::5/64 Guest 1 IPv6 is working fine, Guest 2 too. As suggested by the wiki article (1) i split my /64 network into a /112. Is it right to set the host /112 and the guests /64? Why is that?

    Read the article

  • How to get an inactive RAID device working again?

    - by Jonik
    After booting, my RAID1 device (/dev/md_d0 *) sometimes goes in some funny state and I cannot mount it. * Originally I created /dev/md0 but it has somehow changed itself into /dev/md_d0. # mount /opt mount: wrong fs type, bad option, bad superblock on /dev/md_d0, missing codepage or helper program, or other error (could this be the IDE device where you in fact use ide-scsi so that sr0 or sda or so is needed?) In some cases useful info is found in syslog - try dmesg | tail or so The RAID device appears to be inactive somehow: # cat /proc/mdstat Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [raid10] md_d0 : inactive sda4[0](S) 241095104 blocks # mdadm --detail /dev/md_d0 mdadm: md device /dev/md_d0 does not appear to be active. Question is, how to make active the device again (using mdmadm, I presume)? (Other times it's alright (active) after boot, and I can mount it manually without problems. But it still won't mount automatically even though I have it in /etc/fstab: /dev/md_d0 /opt ext4 defaults 0 0 So a bonus question: what should I do to make the RAID device automatically mount at /opt at boot time?) This is an Ubuntu 9.10 workstation. Background info about my RAID setup in this question.

    Read the article

  • Can enabling a RAID controller's writeback cache harm overall performance?

    - by Nathan O'Sullivan
    I have an 8 drive RAID 10 setup connected to an Adaptec 5805Z, running Centos 5.5 and deadline scheduler. A basic dd read test shows 400mb/sec, and a basic dd write test shows about the same. When I run the two simultaneously, I see the read speed drop to ~5mb/sec while the write speed stays at more or less the same 400mb/sec. The output of iostat -x as you would expect, shows that very few read transactions are being executed while the disk is bombarded with writes. If i turn the controller's writeback cache off, I dont see a 50:50 split but I do see a marked improvement, somewhere around 100mb/s reads and 300mb/s writes. I've also found if I lower the nr_requests setting on the drive's queue (somewhere around 8 seems optimal) I can end up with 150mb/sec reads and 150mb/sec writes; ie. a reduction in total throughput but certainly more suitable for my workload. Is this a real phenomenon? Or is my synthetic test too simplistic? The reason this could happen seems clear enough, when the scheduler switches from reads to writes, it can run heaps of write requests because they all just land in the controllers cache but must be carried out at some point. I would guess the actual disk writes are occuring when the scheduler starts trying to perform reads again, resulting in very few read requests being executed. This seems a reasonable explanation, but it also seems like a massive drawback to using writeback cache on an system with non-trivial write loads. I've been searching for discussions around this all afternoon and found nothing. What am I missing?

    Read the article

  • Configure all hosts, then create a list of the config for all hosts?

    - by AME
    I deployed a huge number of hosts with Ansible - which did work very nice. Each host got its individual settings and configuration. Now I'd like to generate a config file for another system that uses these hosts. For it, I need for every host a part of the generated configuration (the one that configures the database). Here is an example of the situation with two hosts having different configuration and the other system that uses a part of the Ansible-generated configuration: host1 ansible configured dbA host2 ansible configured dbQ The other system: host1 = dbA host2 = dbQ The values are computed differently (dbQ instead of dbB for host2 for example) if it belongs in a different cluster and so on, making it unpractical to just read out host configuration from the host_vars. I believe I would need to iterate over the hosts and let Ansible figure out the computed values for the variables like it would when deploying, but I do not know how to put that result in one template. Please advise :)

    Read the article

  • Configure postfix to filter email into hold queue

    - by Ian
    Hey, I would like postfix to send all emails received on SMTP off to an external process, which will decide whether to allow them through as normal, or whether to put them into the hold queue (or another quarantine area), where they have to wait for admin approval. I was thinking of doing this with an after-queue content filter, which uses pipe(8) to run a script on each message, and the script itself will spawn "postsuper -h " if it decides to put the message on hold. Then the admin can do postsuper -d or -r to delete or pass the message on as appropriate. So, my questions are - a) will this work, and b) is this the best way to do it? Would a milter or another type of content filter be a better approach?

    Read the article

  • How to make ssh/rsync/etc use a VLAN network interface?

    - by Annan
    A company I work for has a number of virtual servers with ElasticHosts. They are setup in such a way that eth1 is on a private VLAN connecting them to each other. This is so backups sent between servers are not charged at the same rate as external data transfer. My understanding of how VLANs and network interfaces work is sketchy at best. How can I make ssh, rsync, etc. transfer data through the VLAN? My final solution: I spent a while trying to figure this out, For all servers involved, edit /etc/sysconfig/network-scripts/ifcfg-eth1 DEVICE=eth1 BOOTPROTO=static ONBOOT=yes HWADDR=YOUR_MAC_ADDR IPADDR=192.168.0.100 NETMASK=255.255.255.0 Where HWADDR should already be set and the last octate of IPADDR should be different from each other. Then run, on all servers /etc/init.d/network restart After this the IP addresses specified by IPADDR can be used directly as any other IP address.

    Read the article

  • Hang while starting several daemons

    - by Adrian Lang
    I’m running a Debian Squeeze AMD64 server. Target runlevel after boot is runlevel 2, which includes rsyslogd, cron, sshd and some other stuff, but not dovecot, postfix, apache2, etc. The system fails to reach runlevel 2 with several symptoms: The system hangs at trying to start rsyslogd Booting into runlevel 1 works, then login from the console works Starting rsyslogd from runlevel 1 via /etc/init.d/rsyslog hangs Starting runlevel 2 with rsyslogd disabled works But then, logging in via console fails: I get the motd, and then nothing Starting sshd from runlevel 1 succeeds But then, I cannot login via ssh. Sometimes password ssh login gives me the motd and then nothing, sometimes not even this. Trying to offer a public key seems to annoy the sshd enough to not talk to me any further. When rebooting from runlevel 1, the server hangs at trying to stop apache2 (which is not running, so this really should be trivial). Trying to stop apache2 when logged in in runleve 1 does hang as well. And that’s just the stuff which fails all the time. RAM has been tested, dmesg shows no problems. I have no clue. Update: (shortened) output from rsyslogd -c4 -d called in runlevel 1 rsyslogd 4.6.4 startup, compatibility mode 4, module path '' caller requested object 'net', not found (iRet -3003) Requested to load module 'lmnet' loading module '/user/lib/rsyslog/lmnet.so' module of type 2 being loaded conf.c requested ref for 'lmnet', refcount 1 rsylog runtime initialized, version 4.6.4, current users 1 syslogd.c requested ref for 'lmnet', refcount now 2 I can kill rsyslogd with Strg+C, then. /var/log shows none of the configured log files, though. Update2: Thanks to @DerfK I still have no clue, but at least I narrowed down the problem. I’m now testing with /etc/init.d/apache2 stop (without an apache2 running, of course) which hangs as well and looks like an even more obvious failure. After some testing I found out that a file with one single line: /usr/sbin/apache2ctl configtest /dev/null 2&1 hangs, while the same line executed in an interactive shell works. I was not able to further reduce this line while, i. e. every single part, the stream redirections and the commando itself is necessary to reproduce the hang. @DerfK also pointed me to strace which gave a shallow hint about what kind of hang we have here: wait4(-1for the init scripts futex(0xsomepointer, FUTEX_WAIT_PRIVATE, 2, NULL for rsyslogd / apache2 binaries called by the init scripts The system was installed as a Debian Lenny by my hoster in autumn 2011, I upgraded it to Squeeze immediately and kept it up to date with Squeeze, which then used to be testing. There were no big changes, though. I guess I never tried to reboot the system before.

    Read the article

  • Multiple servers acting like a single one with all the hardware?

    - by marc.riera
    Hello, by now I have 10 servers for hpc, power computing oriented. My users need to launch several processes using qmake. The users are used to work with ubuntu 9.10, and the software from the repositories is switable for them. I've deployed ubuntu 9.10 to all 10 servers (pxe rocks). By now we work with parallel-ssh and cluster-ssh, which allows as to launch the same process to all servers. With this tools this tools the servers remain as independent but with the same software and the same launched command. Now we would like to go to next step and see all the servers as a single one with all the resources from the other 9 as if was its resources. The difference would be substantial in time to process and also time to design the command to launch. Any advice on wich software to use will be very useful? Thanks

    Read the article

< Previous Page | 405 406 407 408 409 410 411 412 413 414 415 416  | Next Page >