Search Results

Search found 33445 results on 1338 pages for 'single instance storage'.

Page 409/1338 | < Previous Page | 405 406 407 408 409 410 411 412 413 414 415 416  | Next Page >

• CHKDSK is unable to fix NTFS errors

  - by HackToHell

  After my PC shutdown due to power failure, I noticed several errors in EventViewer. The file system structure on the disk is corrupt and unusable. Please run the chkdsk utility on the volume \Device\HarddiskVolume2. and The file system structure on the disk is corrupt and unusable. Please run the chkdsk utility on the volume C:. So I forced a chkdsk check at startup, and it finds a stream of error, here is the output, it is smaller than the actual log, because, Event Viewer only seems to have this much, the same line was repeated thousands of times.Here is that line. Some clusters occupied by attribute of type 0x80 and instance tag 0x4 in file 0x198f2 is already in use. Deleting corrupt attribute record (128, "") from file record segment 104690. Attribute record of type 0x80 and instance tag 0x0 is cross linked Also, even after running CHKDSK, the same errors were being reported again so I ran CHKDSK another time and it still loops the same line above, without fixing the error. Can anyone tell me how to fix it?

  Read the article

• Overriding some DNS entries in BIND for internal networks

  - by Remy Blank

  I have an internal network with a DNS server running BIND, connected to the internet through a single gateway. My domain "example.com" is managed by an external DNS provider. Some of the entries in that domain, say "host1.example.com" and "host2.example.com", as well as the top-level entry "example.com", point to the public IP address of the gateway. I would like hosts located on the internal network to resolve "host1.example.com", "host2.example.com" and "example.com" to internal IP addresses instead of that of the gateway. Other hosts like "otherhost.example.com" should still be resolved by the external DNS provider. I have succeeded in doing that for the host1 and host2 entries, by defining two single-entry zones in BIND for "host1.example.com" and "host2.example.com". However, if I add a zone for "example.com", all queries for that domain are resolved by my local DNS server, and e.g. querying "otherhost.example.com" results in an error. Is it possible to configure BIND to override only some entries of a domain, and to resolve the rest recursively?

  Read the article

• How would I setup iMail to forward a user's mail to another service w/o leaving a copy locally?

  - by Scott Mayfield

  I have an iMail 2006 server installation in which I have a particular user that has several aliases that all point to a single user (me, for the record). I've been copying all of my mail to GMail and reading it there, but it annoys me that I have to go back weekly and log into my mail account on iMail and delete between 6 and 10 thousand copies of messages I've already received, in order to keep my mailbox from filling up (yes, I have it set with no quota, but I consider it bad form to just let the box grow indefinitely). I've got the copying setup via an inbound user rule, but I'm wondering how to accomplish a "copy and delete" rule. The manual isn't clear on what happens with multiple matching rules (will they be processed in order, or is it a first match situation?) and there isn't a means to combine multiple actions into a single rule. If I use the "forward" action, I THINK that it's going to screw up all the sender information once the mail reaches my GMail account and show it as coming from me instead of the original senders (can anyone confirm that this is accurate?) An easy answer would be to delete my user account entirely, replace it with an alias that maps to my GMail account, but then I would lose my ability to log into the system for admin duties. So that leads me to creating a second, lesser known account for admin use, but since it's a real account, sooner or later I'm going to get mail sent to it and I'll be back to the same situation of having a user account that doesn't get emptied periodically. I imagine I can set the quota to 0 MB to cause all incoming mail to my admin account to bounce, or setup an inbound rule to bounce everything, but this is starting to sound kludgy to me. Does anyone know of a more direct work around to copying a user's incoming mail to an outside server and then deleting the local copy w/o removing their account entirely? Or is this just wishful thinking?

  Read the article

• mysql INNODB inserts very slow

  - by 133794m3r

  The database's schema is as follows. CREATE TABLE `items` ( `id` mediumint( 8 ) unsigned NOT NULL AUTO_INCREMENT , `name` varchar( 45 ) NOT NULL , `main_type` tinyint( 4 ) NOT NULL , `rarity` tinyint( 4 ) NOT NULL , `stack_size` smallint( 6 ) NOT NULL , `sub_type` tinyint( 4 ) NOT NULL , `cost` mediumint( 8 ) unsigned NOT NULL , `ilvl` smallint( 6 ) unsigned NOT NULL DEFAULT '0', `flavor_text` varchar( 250 ) NOT NULL , `rlvl` tinyint( 3 ) unsigned NOT NULL , `final` tinyint( 4 ) NOT NULL DEFAULT '0', PRIMARY KEY ( `id` ) ) ENGINE = InnoDB DEFAULT CHARSET = ascii; Now, doing an insert on this table takes 0.22 seconds. I don't know why it's taking so long to do a single row insert. Reads are really really fast something like 0.005 seconds. With using the example configuration from here dev mysql innodb it averages ~0.002 to ~0.005 seconds. Why it takes more than 100x more time to do a single insert makes no sense to me. My computer is as follows. OS:Debian Sid x86-x64, Mysql 5.1, RAM:4GB ddr2, cpu 2.0Ghz dual core, HDD 7200RPM 32MB cache 640GB. Why it's taking almost 100x as much time for a SELECT * FROM items; vs INSERT INTO items ...; will never make any sense to me. It's still a small table at only 70 rows, and took that long even when it had 0 rows.

  Read the article

• Gvim on Windows 7: ALT codes not working

  - by John Sonderson

  I would like to be able to enter ALT codes in Gvim on Windows 7 as documented on the following site: Alt Codes On Windows (Windows 7 in my case), to generate a character via an ALT code you make sure that the NumLock key on your keypad is toggled on, hold down the ALT key, enter the keycode on the numeric keypad, and then release the ALT key. However this does not work in Gvim on Windows (which ignores the fact that I am pressing the ALT key and just prints to entered keypad key directly onto the screen). How can I get these keystroke combinations to work in Gvim as well? Thanks. EDIT: As the answer below points out, the way to insert non-ASCII characters for which you do not have entries on your keyboard without changing the keyboard layout is as follows: Make sure you are in insert mode, and then type CTRL-V followed by the Unicode character code of interest, for instance: CTRL-V u00E0 (generates à) CTRL-V u00C8 (generates È) CTRL-V u00E8 (generates è) CTRL-V u00E9 (generates é) CTRL-V u00EC (generates ì) CTRL-V u00F2 (generates ò) etc... See for instance http://unicode-table.com/ for a full list of Unicode character codes. The following list of Unicode characters by language may also be useful: http://en.wikipedia.org/wiki/List_of_Unicode_characters In some cases such as this one, though, there might be an easier way to enter special characters (see :help digraphs and :digraphs). For example, while in insert mode you may be able to type the following: CTRL-K E! (yields É) CTRL-K a' (yields á) Note that as the following page shows: http://code.google.com/p/vim/source/browse/runtime/doc/digraph.txt Gvim 7.4 contains an even wider set of default digraphs than Gvim 7.3, thus providing convenience to an even broader set of languages. Regards.

  Read the article

• Connecting remotely to an SQL server inside a LAN

  - by vondip

  Hello everyone, I am using SQL server 2008 inside my home lan. I've configured it to accept remote connections and I can now connect to the server from other pcs inside the lan. The problems rises when I try connecting to the server from a computer outside of my home lan. I've disabled my router's firewall and I've configured a virtual server on port 1433 forwarding to the correct lan ip. What's wrong? why is it not working? Thank you very much for your help~! Edit: This is the error I keep getting: A network related or instance specific error occured while establishing connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that the SQL SERVER is configued to allow remote connections. (provider : Sql network interfaces, error: 25- Connection string is not valid) OK these are my router's details: edimax br-6204wg I am not sure how I am supposed to browse google.com. can you be a bit more specific?

  Read the article

• Mindtouch broke my Apache2 virtual host configuration.

  - by grenade

  I installed mindtouch using the instructions here and it seems to have broken my Virtual Host configuration. I have several domains running off the same apache instance and this was working fine but now all my domain names resolve to the virtualhost where mindtouch was installed. So mindtouch made all my domain names point to the new mindtouch instance. Grrr! I use debians default virtual host mechanisms (sites-enabled, etc). Does anyone know what apache directive mindtouch is using to ruin my vh setup? I've scoured all the conf files and there is nothing obvious in apache2.conf or httpd.conf that would cause the behaviour. Did it create a sym-link somewhere that I should destroy? I should add that I uninstalled the mindtouch packages already but apache persists in redirecting all domains to the first one mentioned in the sites-enabled folder. thini:~# apache2ctl -S [Wed Jan 05 13:39:11 2011] [warn] NameVirtualHost *:80 has no VirtualHosts VirtualHost configuration: wildcard NameVirtualHosts and _default_ servers: *:* www.openancestry.org (/etc/apache2/sites-enabled/openancestry.org:1) *:* www.pragmantra.com (/etc/apache2/sites-enabled/pragmantra.com:1) *:* services.pragmantra.com (/etc/apache2/sites-enabled/services.pragmantra.com:1) *:* www.subversionreports.com (/etc/apache2/sites-enabled/subversionreports.com:1) *:* www.thijssen.ch (/etc/apache2/sites-enabled/thijssen.ch:1) Syntax OK

  Read the article

• What is the best way to create a failover cluster for my IIS website?

  - by ObligatoryMoniker

  Our eCommerce website www.tervis.com currently runs on two servers: SQL server: 2005 x 86 on Windows Server 2003 Standard x86 with a single dual core processor and 4 gb of memeory IIS server: Windows Server 2008 Web edition x64 with dual quad core hyper threaded processors and 32 gb of memory Tervis.com's revenue has steadily grown to the point where we need to have redundant servers deployed with a fail over mechanism so that we do not have any down time. Because the SQL server is so underpowered compared to the web server my thought was to purchase: 2 x SQL Server 2008 R2 web edition x64 single processor license 2 x Windows Server 2008 R2 Web Edition Licenses 1 x New Physical dual quad core 32 GB server 1 x F5 Load Balancer I need the Windows Server 2008 R2 Web Edition licenses so that I can run SQL and IIS on the same box for both of these servers. The thought is to run this as an active/passive fail over cluster that could be upgraded to an active/active cluster if we purchased the additional SQL licensing. The F5 load balancer would serve as the device that monitors the two servers and if the current active one stops responding then fails over to using the other server. To be clear this is not windows clustering but simply using a load balancer to fail over between two computers so that you now have a cluster in the general sense. Is this really the best way to accomplish what I need? Is there some way to leverage the old server 2003 SQL server to function as the devices that funnels http requests to the appropriate active server and then fails over if a problem occurs? Is there any third party clustering software that might help me accomplish this in a simpler fashion?

  Read the article

• All applications quit when printing on imac OS X 10.5.8

  - by Tamany

  I recently ran a software update. I'm not sure if my problems are associated with this but I'm pretty sure they are as I printed successfully before update. I checked the log at time of printing: 03/05/2010 22:03:15 Microsoft Word[697] *** -[NSCFString _getValue:forType:]: unrecognized selector sent to instance 0x17a82b50 03/05/2010 22:03:15 [0x0-0x51051].com.microsoft.Word[697] Ignoring Quickdraw drawing between QDBeginCGContext and QDEndCGContext 03/05/2010 22:03:16 [0x0-0x51051].com.microsoft.Word[697] Ignoring Quickdraw drawing between QDBeginCGContext and QDEndCGContext 03/05/2010 22:03:16 [0x0-0x51051].com.microsoft.Word[697] Ignoring Quickdraw drawing between QDBeginCGContext and QDEndCGContext 03/05/2010 22:03:16 [0x0-0x51051].com.microsoft.Word[697] Ignoring Quickdraw drawing between QDBeginCGContext and QDEndCGContext 03/05/2010 22:03:16 [0x0-0x51051].com.microsoft.Word[697] Ignoring Quickdraw drawing between QDBeginCGContext and QDEndCGContext 03/05/2010 22:03:16 [0x0-0x51051].com.microsoft.Word[697] Ignoring Quickdraw drawing between QDBeginCGContext and QDEndCGContext 03/05/2010 22:03:17 [0x0-0x51051].com.microsoft.Word[697] Mon May 3 22:03:17 leopards-imac-2.local Word[697] <Error>: The function `CGPDFDocumentGetMediaBox' is obsolete and will be removed in an upcoming update. Unfortunately, this application, or a library it uses, is using this obsolete function, and is thereby contributing to an overall degradation of system performance. Please use `CGPDFPageGetBoxRect' instead. 03/05/2010 22:22:09 Microsoft Word[697] *** -[NSCFString _getValue:forType:]: unrecognized selector sent to instance 0x1b036500 Any thoughts on how to fix this?

  Read the article

• What is the best way/Software to manage multiple short lived instances of virtual machines ?

  - by Newtopian

  Hi, We have a QA department that have to test our software on multiple combination of OS and DMBS. With Windows spewing out many different versions the combinatorial math of all this can be daunting. So we decided on visualizing our setups but so far it only displaces the problem. The cost of hardware is expensive and we need many different combination far exceeding your server capacity to deliver. Also, these instances are throw away, once the test is complete we no longer need it, furthermore to ensure proper test isolation we should start fresh from a new instance. Lastly we only need a small subset of these system online at any given time. What I am looking for is a way to manage inventory so that our QA staff can order instances to be put online as required and discarded once used. Instances are spawned from a pool of freshly installed systems with the appropriate combination ready to accept our software. It also should be possible for two or more people to start the same instance at the same time, though we could manage without this if it proves too complex to put in place. Finally our budget is pretty thin, we can probably make some purchases but ideally expenditures should be kept to a minimum. To summarize we should be able to : Bring instances online on demand. Ideally should offer queue and scheduling management Destroy instances on demand Keep masters in inventory but not online. Manage large inventory of VMs (30-100 maybe more) with small staff of users (5-10). Allow adding, deleting and changing instances from inventory (bring online, make changes and check back in, or create new and check in). Allow few long lived instances for support tools (normal VM server usage) Thanks for your answers

  Read the article

• Wireless connection drops when wired computer starts a game.

  - by Skadlig

  Starting this week I have had a strange problem on my network. Some background of my setup: Internet is provided by a adsl-modem. A D-link Dir-600 router is hooked up to to adsl-modem. My computer is hooked up to the router using a cat-5 cable. My wife's computer is hooked up using a wireless usb dongle, TP-Link TL-WN821N. Both computers use windows 7 64-bit home premium. Up until this week everything was normal, we could for instance play Dungeons & Dragons Online together without any network issues. Now every time I start DDO or any other network game, for instance L4D, the whole wireless network drops. I have confirmed that it's not just her computer using an Samsung Galaxy Spica android phone. Shutting down the game on my end restores the wireless connection automagicly. My wife can start DDO without the net dropping but if I plug in a wireless network card in my computer and start up the game the connection drops. So it seems like something my computer, and my computer only, does when starting a game makes the wireless connection write a sad note and kill it self but for the life of me I can't figure out what that might be. I could hook her computer up using cat-5 but I would prefer not to do that. Does anyone have any suggestions as to what the problem might be, what I can do to fix it or what I should do to get more data regarding what is happening?

  Read the article

• Postfix: Modify sender address based on recipient

  - by PJ P

  We have a Postfix server that receives mail from our application servers. Senders are in the form [email protected] (where host.fqdn can vary, depending on source server) and recipients can be internal or external users. Messages going to external users should have the sender changed to [email protected]. I have tried using canonical maps, but since that is handled by the cleanup daemon, before any transport decisions are made, it would affect all sender addresses. I have also tried creating a custom smtp transport with generic mappings and configuring transport_maps to use that custom smtp transport for external domains. However, generic mappings affect both sender and recipient addresses. Lastly, I've tried the following: Create a custom smtpd daemon that specifies sender canonical maps and a unique transport table. Send all externally addressed mail to that custom daemon. Ideally, sender canonical maps would transform the sender address and the unique transport table would relay messages to the internet. However, evidently, only one transport table can be used per Postfix instance. I want to avoid creating an entirely new Postfix instance to accommodate this rewriting. Any suggestions? (and thanks in advance)

  Read the article

• Joining Samba to Active Directory with local user authentication

  - by Ansel Pol

  I apologise that this is somewhat incoherent, but hopefully someone will be able to make enough sense of this to understand what I'm trying to achieve and provide pointers. I have a machine with two network interfaces connected to two different networks (one of which it's providing several other services for, such as DNS), running two separate instances of Samba, one bound to each interface. One of the instances is just a workgroup-style setup using share-level authentication, which is all working fine. The problem is that I'm looking to join the other instance to an MS Active Directory domain (provided by MS Windows Small Business Server 2003) to enable a subset of the domain users to access the shares from Windows machines on the other network. The users who need access from the domain environment have accounts (whose names are all-lowercase versions of their domain usernames) on the machine running Samba, but I'm not sure about how to map the UIDs and everything I've read concerns authenticating accounts on that machine against either AD or another LDAP server. To clarify: I only want the credentials for AD users accessing the non-workgroup Samba instance to be authenticated against AD, not the accounts on the machine running Samba. I hope this is sufficiently clear. EDIT: In addition to being able to access the Samba shares from AD, I do also need to be able to access a share on the domain from the machine running Samba but would still like everything non-Samba-related to authenticate locally.

  Read the article

• Mac OS X duplex printing problem: one- vs. multi-paged documents

  - by Christian Lindig

  I like to print on pre-printed stationery using the Preview.app and a duplex-capable HP Color Laserjet 4700 (PostScript) printer. The print dialog handles one and two-paged documents differently: the paper needs to be placed differently into the tray if the document contains one page versus when it contains two pages. This is not obvious when printing on plain paper but becomes obvious when front and reverse side of sheets are marked. Otherwise the first page would end up on the reverse side of the first sheet. I believe the problem is caused by the printer driver setting duplex printing to false (using the PostScript setpagedevice operator) when emitting a single-page document versus keeping it set to true when emitting multi-page documents. All this despite that duplex printing is always specified in the printer dialog. When printing a single-sided document, duplex=true and duplex=false seem to make a difference with respect which side of a sheet gets printed on. It would be also helpful if others could confirm the problem actually exists. I suspect this problem is not limited to specific printers. I'm on OS X 10.6 and I checked two different HP printers.

  Read the article

• Is there a free PDF printer / distiller that creates signable documents?

  - by Coderer

  I've used various methods (mentioned elsewhere on this site) to create PDFs, using a printer driver or converting from PostScript, etc. The common problem is that if I open any of the output files in the newer versions of Adobe Reader, there's an option to "Place Signature" but it's greyed out, or gives an error message that the feature has been disabled for this document. As far as I can tell, there's an option set somewhere in the document metadata that tells Reader "allow the user to sign this document", or don't. None of the free/open source tools that have been been linked to in other SU posts have had this listed as an option (though to be fair I haven't actually downloaded and tried all of them). Is there a tool that does this? Can I just poke a bit with a hex editor somewhere to turn on this functionality? I can sometimes get access to Acrobat Professional to turn on this option, but doing it for every desired case would be more work than I care to do. The current workaround for single-page documents is: Print the document to PDF (possibly via postscript) Open a single-page blank PDF with the "signable" bit turned on in Reader create a custom "stamp" using the Reader markup tools, by importing the printed-to document "stamp" an image of the printed document on the blank page, hoping to get it centered about right place a signature over the document-but-not-really you just stamped This obviously does not scale well at all. It would be much better if I could: Print the document to PDF Drag the document to a simple shortcut / tool / whatever Open the document in Reader Place a signature in the document ETA: Sorry, maybe I should have been clearer -- I'm talking about the certificate-based digital signing available in Adobe Reader, not adding a virtual ink signature. Also, any solution really would have to be available offline.

  Read the article

• Choice of an OS for a home ZFS NAS

  - by OlafM

  I am preparing a home NAS with an old Athlon 64 X2 3800+, 4 GB ECC RAM, Asus M2V MX motherboard, and a single 3 TB WDC Green (another one as mirror may be installed in the future). It's the cheapest solution I found that includes ECC memory and the higher energy consumption is offset by the lower (zero) cost of acquisition. The system will be used for: music storage and stream to other desktop computers; storage of the scanned dia slides (3-4k slides, 180 MB TIFF each one plus reduced quality JPEG version); stream of these photos to a local iPad 2 (maybe Plex App? not yet sure); (one additional) remote backup via rsync/ssh or ZFS send/receive. It will be controlled via remote ssh, maybe VNC, no monitor attached. Absolute requirement is a reliable ZFS solution, plus the ability to easily install packets/software/virtual machines and to update remotely (I will be the admin and I don't live near the NAS). I have mainly three options: NAS4free/FreeNAS OpenIndiana Solaris Express 11 (yeah yeah I know the license requirements, I will write a perl script on it to count it as development machine). Problems: NAS4free/FreeNAS (I tested only NAS4free) required embedded installation for remote upgrading, but full install for easy addition of software packets. Since I need at least AirVideo Server (linux/win) and Plex App (win/linux) to stream the photos and some videos to iPad (they both require virtualbox), but I cannot be there to install updates, NAS4free/FreeNAS are excluded. http://www.nas4free.org/general_information.html explains the issue: embedded can be remotely updated, full cannot. Solaris has also another advantage: Crashplan client supports Solaris and I'm already using it for other backups. I would like to leave the option open, even if I will be doing backups probably through zfs send/receive. NexentaStor was left out because zfs send/receive are not included in the free version. The question is now Solaris 11 Express over OpenIndiana. To ease the management, I will be using http://www.napp-it.org Which one would you suggest and why? I found lots of informations and it's difficult for me to decide. I think (from the napp-it manual) that Solaris has some additional options for SMB shares, but are they really needed at home? I think I won't even use ACLs, since normal unix-style permissions are enough. OpenIndiana has maybe more frequent updates (Solaris offers only security updates between releases), but again, do I need them? I don't think so. Moreover, this is a NAS that has to work and nothing else, I cannot risk having problems that require me to access the server. Isn't OpenIndiana a bit more... cutting edge (in the Solaris world)? I'm just asking, no need to focus on this for the answer :-) I would limit myself to these two options (SE11.1/OI) also because I will be making a NAS for me in the future (where high performances with Mac shares are also required) and Solaris has kernel support for AFP. I will use this server to gather experience as well. After this long question, thanks in advance! If you need additional info, let me know and I will update this post.

  Read the article

• What's the piece of hardware listening on Facebook's or Wikipedia's IP address?

  - by Igor Ostrovsky

  I am trying to understand how massive sites like Facebook or Wikipedia work, for my intellectual curiosity. I read about various techniques for building scalable sites, but I am still puzzled about one particular detail. The part that confuses me is that ultimately, the DNS will map the entire domain to a single IP address, or a handful of IP addresses in the case of round-robin DNS. For example, wikipedia.org has only one type-A DNS record. So, people from all over the world visiting Wikipedia have to send a request to the one IP address specified in DNS. What is the piece of hardware that listens on the IP address for a massive site, and how can it possibly handle all the load coming from the requests for users all over the world? Edit 1: Thanks for all the responses! Anycast seems like a feasible answer... Does anyone know of a way to check whether a particular IP address is anycast-routed, so that I could verify that this really is the trick used in practice by large sites? Edit 2: After more reading on the topic, it appears that anycast is not typically used for dynamic web content. Anycast is usually used for UDP (e.g., DNS lookups), or sometimes for static content. One interesting thing to note is that Facebook uses profile.ak.fbcdn.net to host static content like style sheets and javascript libraries. Each time I ping this name, I get a response from a different IP address. However, I can't tell whether this is anycast in action, or a completely different technique. Back to my original question: as far as I can tell, even a large site will have a single expensive piece of load-balancing hardware listening on its handful of public IP addresses.

  Read the article

• All applications quit when printing on imac OS 10.5.8

  - by Tamany

  Hello and hoping someone might be able to help. Recently ran software update (not sure if problems are associated with this but pretty sure they are as i printed successfully before update. checked log at time of printing: any thoughts on how to fix this? THANKYOU!! 03/05/2010 22:03:15 Microsoft Word[697] * -[NSCFString _getValue:forType:]: unrecognized selector sent to instance 0x17a82b50 03/05/2010 22:03:15 [0x0-0x51051].com.microsoft.Word[697] Ignoring Quickdraw drawing between QDBeginCGContext and QDEndCGContext 03/05/2010 22:03:16 [0x0-0x51051].com.microsoft.Word[697] Ignoring Quickdraw drawing between QDBeginCGContext and QDEndCGContext 03/05/2010 22:03:16 [0x0-0x51051].com.microsoft.Word[697] Ignoring Quickdraw drawing between QDBeginCGContext and QDEndCGContext 03/05/2010 22:03:16 [0x0-0x51051].com.microsoft.Word[697] Ignoring Quickdraw drawing between QDBeginCGContext and QDEndCGContext 03/05/2010 22:03:16 [0x0-0x51051].com.microsoft.Word[697] Ignoring Quickdraw drawing between QDBeginCGContext and QDEndCGContext 03/05/2010 22:03:16 [0x0-0x51051].com.microsoft.Word[697] Ignoring Quickdraw drawing between QDBeginCGContext and QDEndCGContext 03/05/2010 22:03:17 [0x0-0x51051].com.microsoft.Word[697] Mon May 3 22:03:17 leopards-imac-2.local Word[697] : The function CGPDFDocumentGetMediaBox' is obsolete and will be removed in an upcoming update. Unfortunately, this application, or a library it uses, is using this obsolete function, and is thereby contributing to an overall degradation of system performance. Please useCGPDFPageGetBoxRect' instead. 03/05/2010 22:22:09 Microsoft Word[697] * -[NSCFString _getValue:forType:]: unrecognized selector sent to instance 0x1b036500

  Read the article

• Multimaster Keepalived Configuration (Virtual IP with Load Balancing)

  - by Rad Akefirad

  Here are requirements: 1. High Availability 2. Load Balancing First configuration 1. Two linux servers have been configured with one static IP for each: 10.17.243.11, 10.17.243.12 2. Keepalived has been installed and configured with one VRRP instance to provide one virtual IP (10.17.243.10 as VIP, 10.17.243.11 as master and 10.17.243.12 as backup). 3. Everything works fine. The VIP is assigned to the master server (10.17.243.11) as long as it is up and running. As soon as it goes down, the VIP will be assigned to the backup server (10.17.243.12). 4. The problem here is all communication goes to the master server. Second configuration 1. I found active-active configuration for Keepalived which is possible by defining more than one VRRP instance. So that both server have two IPs (real 10.17.243.11 and virtual 10.17.243.10 for server #1 and real 10.17.243.12 and virtual 10.17.243.20 for server #2. 2. Everything works fine. we have two VIPs which are accessible (HA). But all communication coming to each IP still goes to one single machine (either server #1 or #2 depending on the IP). However I found some tricks on the DNS to overcome this limitation. But it's not acceptable in our case. Question: Is there any way to have one virtual IP which is assigned to both servers? By that I mean both servers are handling some part of workload (like the thing we do in web server load balancing)? By using either keepalived or some other tools? Thanks in advance.

  Read the article

• Can I run Excel 2010 on a server?

  - by Glen Little

  This question is not about a person using Excel on a computer that happens to have an Windows Server OS. And it is not about using any Sharepoint services features! The question is about automated processes that use code (Office Automation) to open Excel files, manipulate them, run calculations, read data, save copies of the file and close the files... all in code. In previous versions of Excel the licensing agreement prevented use on a public server, notes from Microsoft warned about the problems trying to use Office Automation in a server environment, and we were warned that Excel was single threaded and not designed for use on a server. Most of the articles about this were written before Office 2010. But now, Excel 2010 is designed to work on a High Performance Computing server using HPC Services for Excel. One HPC document mentions "Windows HPC Server 2008 R2 includes a comprehensive pop-up manager that can handle occasional dialog boxes and pop-up messages". So my question is... is it now "safe" to run code that automates Excel 2010 on a "normal" server without using the HPC services? If not, can the HPC Services for Excel work on a single server? I don't need the high performance, distributed computing, aspect of HPC Services for Excel... just the ability to run Excel on a server. Can that now be done? Thanks, Glen

  Read the article

• Bash Parallelization of CPU-intensive processes

  - by ehsanul

  tee forwards its stdin to every single file specified, while pee does the same, but for pipes. These programs send every single line of their stdin to each and every file/pipe specified. However, I was looking for a way to "load balance" the stdin to different pipes, so one line is sent to the first pipe, another line to the second, etc. It would also be nice if the stdout of the pipes are collected into one stream as well. The use case is simple parallelization of CPU intensive processes that work on a line-by-line basis. I was doing a sed on a 14GB file, and it could have run much faster if I could use multiple sed processes. The command was like this: pv infile | sed 's/something//' > outfile To parallelize, the best would be if GNU parallel would support this functionality like so (made up the --demux-stdin option): pv infile | parallel -u -j4 --demux-stdin "sed 's/something//'" > outfile However, there's no option like this and parallel always uses its stdin as arguments for the command it invokes, like xargs. So I tried this, but it's hopelessly slow, and it's clear why: pv infile | parallel -u -j4 "echo {} | sed 's/something//'" > outfile I just wanted to know if there's any other way to do this (short of coding it up myself). If there was a "load-balancing" tee (let's call it lee), I could do this: pv infile | lee >(sed 's/something//' >> outfile) >(sed 's/something//' >> outfile) >(sed 's/something//' >> outfile) >(sed 's/something//' >> outfile) Not pretty, so I'd definitely prefer something like the made up parallel version, but this would work too.

  Read the article

• Command line scripts to restore the 4 system databases of MS SQL Server 2008

  - by ciscokid

  Hi there, can someone give me some advice on how to restore the 4 system databases (master, msdb, model, tempdb) of a sql server 2008 please? I've already done some testing myself (on restoring the master database) with the following commad line script as a result: ::set variables set dbname=master set dbdirectory=C:\Program Files\Microsoft SQL Server\MSSQL10.MSSQLSERVER\MSSQL\DATA title Restoring %dbname% database net stop mssqlserver cd C:\Program Files\Microsoft SQL Server\MSSQL10.MSSQLSERVER\MSSQL\Binn sqlservr -m sqlcmd -Slocalhost -E -Q "restore database master from disk='c:\master.bak' WITH REPLACE" net start mssqlserver pause After the execution of the 'sqlservr -m' command (used to start the server instance in single-user mode, which is only necessary when restoring the MASTER database), the script stops. So in order to execute the last 2 commands I need to separate the script into 2 smaller scripts, and run them one after the other. Does anyone has an idea on how I can merge them into one single script that runs completely without any interruption? I also want to restore the other 3 system databases using command line scripts like this one. Can someone please advice me how I need to go on? I've already noticed that restoring the temdb is not so easy, but there has to be a way... Looking forward to your advice!

  Read the article

• AWS VPC ELB vs. Custom Load Balancing

  - by CP510

  So I'm wondering if this is a good idea. I have a Amazon AWS VPC setup with a public and private subnets. So I all ready get the Internet Gateway and NAT. I was going to setup all my web servers (Apache2 isntances) and DB servers in the private subnet and use a Load Balancer/Reverse Proxy to pick up requests and send them into the private subnets cluster of servers. My question then, is Amazons ELB's a good use for these, or is it better to setup my own custom instance to handle the public requests and run them through the NAT using nginx or pound? I like the second option just for the sake of having a instance I can log into and check. As well as taking advantage of caching and fail2ban ddos prevention, as well as possibly using fail safes to redirect traffic. But I have no experience with their ELB's, so I thought I'd ask your opinions. Also, if you guys have an opinion on this as well, would using the second option allow me to only have 1 public IP address and be able to route SSH connections through port numbers to respective instances? Thanks in advance!

  Read the article

• Connect Chrome to TOR

  - by Jack M

  I'm having difficulty connecting Chrome to TOR. I started trying yesterday. I started Vidalia and the TOR Browser and then followed the advice at http://lifehacker.com/5614732/create-a-tor-button-in-chrome-for-on+demand-anonymous-browsing - downloading Proxy Switchy and setting it up as stated. This resulted in Error 130 (net::ERR_PROXY_CONNECTION_FAILED) (in Chrome, when I tried to load a webpage). So I looked into Vidalia's settings and noticed that it appeared to be using port 9051, so I set that instead of 8118 as everyone on the internet seems to be suggesting. Then I got a new error: Error 111 (net::ERR_TUNNEL_CONNECTION_FAILED). Digging a bit, I found that Tor should be set as a SOCKS proxy, not an HTTP proxy, so I unticked "use same settings for all protocols" in Proxy Switchy and just set localhost:9051 for SOCKS. That got me Error 7 (net::ERR_TIMED_OUT). And that's when I came here for help. I typed up the above question, but then at the last minute decided to do a bit more reading and found someone here suggested using some command line arguments via a Windows shortcut: "C:\snip\chrome.exe" --proxy-server=";socks=127.0.0.1:9051;sock4=127.0.0.1:9051;sock5=127.0.0.1:9051" --incognito check.torproject.org And that worked perfectly. Yesterday. Today it doesn't, so I'm having to post this question after all. check.torproject.org gives me a "no" with Chrome, but a "yes" with the default Tor Browser. I tried closing Chrome and restarting it (yes, with the correct shortcut) after Vidalia started, but still nothing. The port number hasn't changed or anything. What gives? EDIT: I realized I had a "non tor" instance of Chrome running and that possibly the was causing the command line args t be ignored when I started the new instance. Closed all instances of chrome and ran my Chrome Tor shortcut, and it did get rid of the "not using Tor" message -- because I got another Time Out error instead. Vidalia's bandwidth graph didn't even blink.

  Read the article

• New SSD, is the MBR broken? DISK BOOT FAILURE

  - by Shevek

  I've been running Windows 7 on a WD 500gb SATA single drive, single partition setup for some time with no issues. I've just installed a new Kingston V Series 64gb SSD and performed a clean install of Win7 to it, deleting the partitions on the 500gb and using that as a data drive. All was well for a few reboots but then I started to get "DISK BOOT FAILURE, INSERT SYSTEM DISK AND PRESS ENTER" messages. If I put the Win7 install DVD back in the drive it boots fine. Tried a clean install again, after replacing SATA cables and swapping SATA ports, with a complete partition wipe of both drives. Again, rebooted fine a few times then back with the "DISK BOOT FAILURE" error. Looked on the web and found some discussions about it so I then started from scratch again. This time I wiped the MBR on both drives using MBRWork, disconnected the 500gb and reinstalled to the SSD. Removed the install DVD and installed all the drivers which involved many reboots, all with no problem. To make sure I also did a few cold boots as well. Reconnected the 500gb, initialised, partitioned and formatted it. Copied data to it and did some more reboots and shutdowns. All was ok. Then out of the blue comes another "DISK BOOT FAILURE" and again, if the Win7 install DVD is in the drive it boots fine. So, is the SSD a bad'un? TIA UPDATE: It was a BIOS issue! I found a hidden away option for HDD boot order, which was separate from the usual HDD/CDRom/FDD boot order option. The WD was set to boot before the SSD... Swapped them round and all is well. Still don't understand how it worked at first though... Thanks Solaris

  Read the article

< Previous Page | 405 406 407 408 409 410 411 412 413 414 415 416  | Next Page >