Search Results

Search found 12933 results on 518 pages for 'collaboration tools'.

Page 419/518 | < Previous Page | 415 416 417 418 419 420 421 422 423 424 425 426  | Next Page >

  • Application stuck in TCP retransmit

    - by SandeepJ
    I am running Linux kernel 3.13 (Ubuntu 14.04) on two Virtual Machines each of which operates inside two different servers running ESXi 5.1. There is a zeromq client-server application running between the two VMs. After running for about 10-30 minutes, this application consistently hangs due to inability to retransmit a lost packet. When I run the same setup over Ubuntu 12.04 (Linux 3.11), the application never fails If you notice below, "ss" (socket statistics) shows 1 packet lost, sk_wmem_queued of 14110 (i.e. w14110) and a high rto (120000). State Recv-Q Send-Q Local Address:Port Peer Address:Port ESTAB 0 12350 192.168.2.122:41808 192.168.2.172:55550 timer:(on,16sec,10) uid:1000 ino:35042 sk:ffff880035bcb100 <- skmem:(r0,rb648720,t0,tb1164800,f2274,w14110,o0,bl0) ts sack cubic wscale:7,7 rto:120000 rtt:7.5/3 ato:40 mss:8948 cwnd:1 ssthresh:21 send 9.5Mbps unacked:1 retrans:1/10 lost:1 rcv_rtt:1476 rcv_space:37621 Since this has happened so consistently, I was able to capture the TCP log in wireshark. I found that the packet which is lost does get retransmitted and even acknowledged by the TCP in the other OS (the sequence number is seen in the ACK), but the sender doesn't seem to understand this ACK and continues retransmitting. MTU is 9000 on both virtual machines and througout the route. The packets being sent are large in size. As I said earlier, this does not happen on Ubuntu 12.04 (kernel 3.11). So I did a diff on the TCP config options (seen via "sysctl -a |grep tcp ") between 14.04 and 12.04 and found the following differences. I also noticed that net.ipv4.tcp_mtu_probing=0 in both configurations. Left side is 3.11, right side is 3.13 <<net.ipv4.tcp_abc = 0 <<net.ipv4.tcp_cookie_size = 0 <<net.ipv4.tcp_dma_copybreak = 4096 14c11 << net.ipv4.tcp_early_retrans = 2 --- >> net.ipv4.tcp_early_retrans = 3 17c14 << net.ipv4.tcp_fastopen = 0 >> net.ipv4.tcp_fastopen = 1 20d16 << net.ipv4.tcp_frto_response = 0 26,27c22 << net.ipv4.tcp_max_orphans = 16384 << net.ipv4.tcp_max_ssthresh = 0 >> net.ipv4.tcp_max_orphans = 4096 29,30c24,25 << net.ipv4.tcp_max_tw_buckets = 16384 << net.ipv4.tcp_mem = 94377 125837 188754 >> net.ipv4.tcp_max_tw_buckets = 4096 >> net.ipv4.tcp_mem = 23352 31138 46704 34a30 >> net.ipv4.tcp_notsent_lowat = -1 My question to the networking experts on this forum : Are there any other debugging tools or options I can install/enable to dig further into why this TCP retransmit failure is occurring so consistently ? Are there any configuration changes which might account for this weird behaviour.

    Read the article

  • Running MS Access Programs

    - by fredhappier
    I have an old program developed in MS Access and would like to convert it to Kexi somehow. The program on Windows is launched with Access. Is there any way that Kexi can launch this program? I know my way around Ubuntu and the terminal, but not well versed on databases. Once you make something in Kexi how do you "run" it or "view" what you've made? So far I am able to import the MDB file into Kexi and see all of the database data, but that is as far I have gone. The program was made by a relative years ago for my dad. I myself am an Ubuntu only user for 6+ years now and have no intentions to touch Windows and am looking for a linux solution. My dad is also an Ubuntu user, hence why Im looking for a solution. If Kexi cannot launch and run an MDB file, what else can I try? Anything browser based? Any tips or direction would be extremely helpful. I spoke to my brother who originally made the program. I told him about Kexi and here is what he said. Does any of this make sense? Thanks. This is how I would try to get them to work: Stand alone setup - after import, look for an option where you designate which form object you want to open upon startup. It might be in the tools tab in the picture below. After you save that change, it re-start it and it should work. Front end/back end setup - Do what I suggested for the stand alone setup to the "front-end" MDB file. After you do that, put the other file (table MDB file) where you want it to reside on the network. Now, open back up the "front end" file and look for an option that will allow you to "connect" to those tables in the other file. It looks like it could be in the "External data" tab in the picture below. For this setup, you may need to do these two tasks in the reverse order I just mentioned. Thanks! Fred

    Read the article

  • ?????????????????????????|WebLogic Channel|??????

    - by ???02
    Java EE????????·????????????????/??????????????????????·?????????????????????????WebLogic Server?????????????WebLogic Server???????????????????·??????????????????????????????????????????????????????????(???)???????WebLogic Server??????? ????WebLogic Server 11g(10.3.5)??????????????????????????????????????????????????(1)WebLogic Server???????(2)????????????????(3)?????????????(4)JDBC????????????(5)????????????? ???????Windows?WebLogic Server??????10.3.5????????Oracle Database Express Edition????????????????????????????????????EXE???ZIP???2????????????????EXE??????? ???????????????????????????????????????????????????????????????????????????????????????????????????????????????????????MIDDLEWARE_HOME(?????????????)(????????????????)C:\Oracle\MiddlewareWebLogic Server??????????????Oracle CoherenceOracle Enterprise Pack for Eclipse?????????·????????????????????????????????????????????????(Windows?????)??????????Windows????????(??????????????)?????Web????Oracle HTTP Server?????????????(????????????????????)Oracle ADF(Application Development Framework)??????????WebLogic Server????????????????(Oracle ADF??????????????????????????????)Fusion Middleware Control???????????(Oracle HTTP Server?????????????????????????????)???????????TokyoDomain???????ID/?????weblogic/welcome1??????????AdminServer:7001????????????Server1:7011Server2:7012???????????????Host1??????????????????????????Host1?Server1???Host2?Server2???????JVMJRockit????????????????????????(???????)C:\Oracle\Middleware\user_projects\domains??????????????????????????????????????? ???WebLogic Server??????????GUI????CUI?????????????????????????????????????????????????·????3??????????????????????????????????GUI???????????????????????¦??????????Oracle WebLogic Server ???????·????????????WebLogic Server?????????????????????!(1)WebLogic Server??????? ???????????????????????????????????????????????????????????????????????????????????·???·???????????????????????????????????????? ????????????????????????????My Oracle Support???????????????????My Oracle Support?????????????????????·?????????????????????????????????????? ?????????????·?????????WebLogic Server????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????? ????????????JDK????????????????????????JDK??????????????????????????????????JDK??????????????????????????????????????·??????????????????????????????????????????????????????????? ???????????Windows????????????????WebLogic Server?Windows?????????????Windows?????????????????????????????????????????????????????Windows????????????????????????????????????????????????????????????????????? ??????????????????????All Users???????·?????????????????????????????????????????????????????????????????? ????????????????????????????????????????????????????(2)???????????????? ???????????????????????????????????????????1??????JDBC??????????Oracle Database????????????Web????????HTTP?????????????????????????? ??????????????????????????????????????????????????????????????????????????domain1??????????????JDKJRockit SDK 1.6????????1????????Server1?????????????7002???ID??????ID:weblogic?????:welcome1 ????????????????????????????????????????2????????????????????????????????????????????????????????????(???????????????)?????????????????????????????????????????????????????????????????????????????Web????·????·???????·????????????????????/??????????????????????(???????·???)?????????????????????????????????????????????????????????????????????????????????????????????????????????????????Web????·???·???????·??????????????????????????????????? ???????????????????WebLogic Server?????????????????? WebLogic Server???????????????Configuration Wizard?????????????????Windows???????????????????????-?Oracle WebLogic?-?WebLogic Server 11gR1?-?Tools?-?Configuration Wizard?????????(UNIX???????WLS_HOME/common/bin/config.sh??????)?????????????????WebLogic???????????????????????????? ????????????????·???????????WebLogic Server???????????????Oracle SOA Suite?Oracle Business Process Management???Fusion Middleware??????????????????????????????????????????????????????????????????????????????????Basic WebLogic Server Domain?????????Basic WebLogic Server Domain?????????????????????????????????????????????????????????? ????????????????JDK???????????????????????????(????????)???????????JDK???????????????????????JRockit????????????????????????JDK????????????????JDK????????????JDK????????????????????? ???????????????????????????????????????????????????????RDBMS???????·????????????????????????????????????????????? ????????????????????????????????????????????????????????????????????????????????????????????????? ??????????????????????????????????DOMAIN\startWebLogic.cmd?(UNIX??????startWebLogic.sh?))???????????????????????ID????????????????????????????????????????<??> ?????????????????????????????(3)????????????? ??????????????????????????????????????????????????7001?????????Web??????http://localhost:7001/?????????????????????????????????????????????ID???????????????????????? ??????????????????????? ??????????????????????????????????????????????(domain1)??????????????????????????????????-?????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????? ??????????????????????????????DOMAIN\bin????????????????????????(??????Server1??????????????7001????)?startManagedWebLogic.cmd Server1 http://localhost:7001 ????????????ID????????????????????????????<??> ??????????????????????????????????????????????????????DOMAIN_HOME\bin\stopManagedWebLogic.cmd?????????????????????????stopManagedWebLogic Server1¦??????????????Oracle???????????????????????·????!(4)JDBC???????????? ????JDBC??????????????Java EE????????·????????JDBC?????????????????????????????????????????????????????????????????????????????????JNDI(Java Naming and Directory Interface)??????????/??????????????????????????????·??????????????????????????? ?????????????????????????????????????????????JDBC???????????????JDBC??????????????????????????????????????????????????????????????????????????????????WebLogic Server????????JDBC??????????????????????????????????????????????????????????????????????????????? ???WebLogic Server???????????????????????????????????????????1?????????????????????????????????????????????????????????????·?????????????????????????????????????????????????????????????????????????Oracle Database????????·?????????Oracle Real Application Clusters(RAC)????????????????????? ???WebLogic Server 11g????????JDBC?????????????MySQL??Oracle Database????????????????????????????????????Oracle Thin Driver 11gojdbc6.jarTYPE4MySQL5.0 JDBC????mysql-connector-java-commercial-5.0.x-bin.jar WebLogic Type4 JDBC????DB2?:wldb2.jarMS SQL Server?:wlsqlserver.jarInformix?:wlinformix.jarSybase?:wlsybase.jarDataDirect?OEM?? ??????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????(*?????)??Oracle Database????????????*WebLogic Server?????dsAJNDI?*JNDI??????????jdbc/dsA????????*Oracle?DB2???1Oracle???????*????????????????1Oracle Thin Instance-Connection????????·??????XA??????????1phase commit???????*???????IDORCL????*???????????Localhost???*?????????????1521??????·?????????????????SCOTT???????????·??????????TIGER????·????*JDBC??????????2oracle.jdbc.OracleDriverURL*JDBC URL?2jdbc:oracle:thin:@localhost:1521:ORCLJDBC????·?????JDBC???? ????????(or SQL)??????????????SQLSQL SELECT 1 FROM DUAL?????WLS?????????????????Server1?1 ????????????BOX?????2 ????????????????? ?????????·?????????????????????????????????????????1??????????????????????????????????????1?????1?????????????????15?????????????????????????1????????????????????????????????????????????(???????????????????)false?????(?)????????????????????????????????????????????????????(???????????????????)120?????????????????????????????????????????????????10????(?)?????????????????????900??????????????(?)?????????????????????????????????????????????????????0(??)???????????(?)????????????????????????????????10??????????(?)?????????????????????????????0???????JDBC????????????SQL????????????????JDBC?????Statement.setQueryTimeout????????????-1?1 ??????????????????????????????????????????????????????????????? ???????????·???(?????)???????????????????????????????????????????????????WebLogic Server????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????? JDBC?????????????????????????????????????????? ?????????????????????????????????????????-?JDBC?-?????????????????????????????JDBC???????????????-??????·????????????? ???JDBC????????????JNDI??????????????????·??????????????????Oracle Database Express Edition???????????????????????????????Oracle?????????·????????XA??????? ???????????????????????????????·?????????????????????????1????·?????????????????????????????????????????????????????????????????????·????????????????????????????????????????????????????????????????????????????JDBC?????????????????????????????????????????? ??????????????????????????????????? ????????????????????????????????????????-?JDBC?-????????????????????????????????????????????????????????????????????¦????????????Oracle WebLogic Server - JDBC??????(5)????????????? ???????????????????????????????????????????????????Java EE 5????????????????????Java EE??????????????????Eclipse?Oracle JDeveloper 11g?Oracle Enterprise Pack for Eclipse 11g????????????????·?????????????????????WebLogic Server?????????????????????????WebLogic Server??????????????????????Web?????????WAR?????EJB?????????JAR????????WAR?JAR????????EAR?????????????? ?????????????????????????????????????????? ?????????????????????????????????????????????????????????????????????????????????????????????????? ?????????????·??????·???????????????????????????????????????????????????????????????? ????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????(????????)???????????????????????????????????? ???????????? ?????????????????????????????????????? ?????????????????????????????????????????????????????-???????????????????????????????????????????????????????? ???????????????????????????????????????????????????????????????????????????????????????????????? ???????WebLogic Server????????????????????????????????????????????????????????????WebLogic Server????????????????????????????????????????????·???????????????/????????????????????????????WebLogic Server????????????????????????????????????????????????????????????WebLogic Server?????????????????¦????????WebLogic Server???···????????????????????!

    Read the article

  • ?? Oracle E-Business Suite Period Close ??

    - by Steve He(???)
    v\:* {behavior:url(#default#VML);} o\:* {behavior:url(#default#VML);} w\:* {behavior:url(#default#VML);} .shape {behavior:url(#default#VML);} Normal 0 7.8 ? 0 2 false false false EN-US ZH-CN X-NONE MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:????; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0cm 5.4pt 0cm 5.4pt; mso-para-margin:0cm; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman","serif";} ?? & ???? — ?? Period Close ???? ????????,??Oracle??????Period Close???,????????????????????????????Oracle E-Business Suite?Period Close?????,???Oracle Financial Assets, General Ledger, Payables, ? Receivables????????????????????????????????????,???????????????????,?????Oracle?????,??????????????,????????????? Oracle???????????????Oracle??????,???????????Oracle?????????????????,????E-Business Suite?????????,??????????????????????????,???????????????,??????????????????????????????,???EBS????,???????????????????????????????Note 167000.1???????????????????????,????????E-Business Suite?????????EBS 12.0.6?????,Oracle?????????????Oracle??,??adpatch????????????EBS??12.1.1???,????????????? Oracle E-Business Suite ?????????: ???? —???????????????????????? ?????? —?????Oracle ???????? ????????—?????????????????????,???? ???????,????????EBS Period Close??,???????SQLGL Period Closing???????????????????????????General Ledger ???????? ?? Select Application??????????????,????? Period Close??????? Period Close ?? Period Closing??????????Execute?? ???????Submit ?? ?? Refresh ??,??????? “In Progress” ?? “Completed” ??View Report?????????? ??????????,????????????????????,?????,?????????????????,?????Oracle???????????,??????????????,????????????????? ??,??????? ??,???????? ??????,??E-Business Suite ???? Diagnostic Tools Community?????????????????,????????Oracle????????? Oracle? Period Close ???,????E-Business Suite?????,????????,?????????????????? Period Close???,??????????,???????????????????,?????????,???????????????,???????????????????,???????,??????????????????????? ???? E-Business Suite Diagnostics Period / Year End Close [ID 402237.1] ??????Closing Period????????????????????????????????Closing Period ??,???????????????????????EBS???????,???E-Business Suite Diagnostics Overview [ID 342459.1].

    Read the article

  • SQL Server 2008 R2 Quiet Installation Failure

    - by pk
    I've downloaded the SQL Server 2008 R2 software from Microsoft and am working on scripting a silent installation. I'm getting the following errors (and the duplicate paste job is not an accident, that's how it shows up for me) The following error occurred: Exception has been thrown by the target of an invocation. Error result: 1152035024 Result facility code: 1194 Result error code: 43216 Please review the summary.txt log for further details The following error occurred: Exception has been thrown by the target of an invocation. Error result: 1152035024 Result facility code: 1194 Result error code: 43216 Please review the summary.txt log for further details Microsoft (R) SQL Server 2008 R2 Setup 10.50.1600.01 This is what shows up in the detailed SQL install log. 2011-02-23 09:53:13 Slp: Running Action: ExecuteInitWorkflow 2011-02-23 09:53:13 Slp: Workflow to execute: 'INITIALIZATION' 2011-02-23 09:53:13 Slp: Error: Action "Microsoft.SqlServer.Configuration.BootstrapExtension.ExecuteWorkflowAction" threw an exception during execution. 2011-02-23 09:53:13 Slp: Microsoft.SqlServer.Setup.Chainer.Workflow.ActionExecutionException: Exception has been thrown by the target of an invocation. ---> System.Reflection.TargetInvocationException: Exception has been thrown by the target of an invocation. ---> System.ArgumentNullException: Value cannot be null. 2011-02-23 09:53:13 Slp: Parameter name: InstallMediaPath Hopefully someone can help me work through this. Here is a simple version of my PowerShell code. $arguments = @() $arguments += "/q" $arguments += "/ACTION=Install" $arguments += "/FEATURES=SQL,Tools" $arguments += "/INSTANCENAME=MSSQLSERVER" $arguments += "/SQLSVCACCOUNT=`"$NetBIOSDomainName\$SQLServerServiceAccount`"" $arguments += "/SQLSVCPASSWORD=`"$SQLServerServiceAccountPassword`"" $arguments += "/SQLSYSADMINACCOUNTS=`"$NetBIOSDomainName\$SQLSysAdminAccount`"" $arguments += "/AGTSVCACCOUNT=`"$NetBIOSDomainName\$SQLServerAgentAccount`"" $arguments += "/IACCEPTSQLSERVERLICENSETERMS" Start-Process "$SQLServerSetupLocation\setup.exe" -Wait -ArgumentList $arguments -RedirectStandardOutput error.txt

    Read the article

  • Unpacking a ZTE ZXV10 H108L router firmware

    - by v3ng3ful
    I binwalked a firmware of a ZTE ZXV10 H108L, and got some encouraging results of uImage uboot, and LZMA compression, as well as a Squashfs 3.0 LZMA compressed filesystem. 256 0x100 uImage header, header size: 64 bytes, header CRC: 0xE70BCBB9, created: Thu Nov 10 04:54:54 2011, image size: 804172 bytes, Data Address: 0x80002000, Entry Point: 0x80266000, data CRC: 0x6EFE90F1, OS: Linux, CPU: MIPS, image type: OS Kernel Image, compression type: lzma, image name: MIPS Linux-2.6.20 320 0x140 LZMA compressed data, properties: 0x5D, dictionary size: 8388608 bytes, uncompressed size: 2637958 bytes 851968 0xD0000 Squashfs filesystem, big endian, lzma signature, version 3.0, size: 2543403 bytes, 632 inodes, blocksize: 65536 bytes, created: Thu Nov 10 04:56:12 2011 Now what I did is, to test several portions of the file (320byte-end, 851968byte-end, and many more) using dd, and trying with certain tools to uncompress/unpack the filesystem of the firmware. After some digging I found out the best tool to do this is the firmware_mod_kit, that understands a squashfs-lzma v3 filesystem. Although I ended up really frustrated as unsquashfs-lzma v3 reported a cold "zlib::uncompress failed, unknown error -3". Do you have any ideas? Could it be that, the firmware is corrupted on purpose to discourage attempts like this? Router file Thanks

    Read the article

  • Importing AMIs from Hyper-v VHDX

    - by jwdaigle
    I have a couple of VHDX files that we use to template locally hosted VMs. I would like to try (some) of these on Amazon, so I need to build an AMI to upload to AWS. I have found http://aws.amazon.com/ec2/vmimport/ , which is very helpful to get started. It appears that AWS does not yet support VHDX, so I found some info that told me to export it out of Hyper-V as a VHD file, and then convert/upload it, which I am in the process of trying out. But the real question is that when I was looking for info, I came across http://stackoverflow.com/questions/14346114/unable-to-rdp-to-ec2-instance . The AWS documentation seems to imply that all I need to do is run the importer and all will be well. True? I dont want to waste all the upload bandwidth and then find out it wont work. Is there something I need to install into the Hyper-V VM before converting/upload it using the AWS command line tools? EC2-Config? Any help greatly appreciated -

    Read the article

  • TortoiseSVN hangs in Windows Server 2012 Azure VM

    - by ZaijiaN
    Following @shanselman's article on remoting into an Azure VM for development, I spun up my own VS 2013 VM, and that image runs on WS 2012. Once I was able to remote in, I started installing all my dev tools, including Tortoise SVN 1.8.3 64bit. Things went south once I started attempting to check out code from my personal svn server. It would hang and freeze often, although sometimes it would work - I was able to partially check out projects, but I would get frequent connection time out errors. My personal svn server (VisualSVN 2.7.2) runs at home on a windows 7 machine, and I have a dyndns url pointing to it. I have also configured my router to passthrough all 443 traffic to the appropriate port on the server. I self-signed a cert and made sure it was imported into the VM cert store under trusted root authorities. I have no problems connecting to my svn server from 4-5 other computers & locations. From the Azure VM, in both IE and Chrome, I can access the repository web browser with no issues. There are no outbound firewall restrictions. I have installed other SVN add-ons for Visual Studio (AnkhSVN, VisualSVN) and attempted to connect with my svn server, with largely the same results - random and persistent connection issues (hangs/timeouts). I spun up a completely fresh WS 2008 Azure VM, and installed TortoiseSVN, and had the same results. So I'm at a loss as to what the problem is and how to fix it. Web searches on tortoisesvn and windows server issues doesn't yield any current or relevant information. At this point, i'm guessing that maybe some setting or configuration that MS Azure VM images is the culprit - although I should probably attempt to spin up my own local WS VM to rule out that it's a window server issue. Any thoughts? I hope I'm just missing something really obvious!

    Read the article

  • "0x80004005: Unspecified error" when renaming folders in Windows 7

    - by Michael Steele
    Setup I've just installed Windows 7 Ultimate 64bit. The operating system is installed on an 80GB Intel X-25M. I have a secondary 500GB Barracuda 7200.12 to be used for storage. This second drive is mounted as 'G'. Problem I'm getting an error whenever I try to rename a folder within this drive. The error says: An unexpected error is keeping you from renaming the folder. If you continue to receive this error, you can use the error code to search for help with this problem. Error 0x80004005: Unspecified error Clicking the "Try Again" button gets past the error, and correctly renames the folder. If I create a folder and leave it's name as "New Folder", then I don't see an error. I'm also able to manipulate files however I want without seeing an error. Things I've Tried Changing permissions on the drive Reformatting the drive. I've tried using both a "Basic" and "Dynamic" partition table. Checking the drive for errors using Microsoft tools Things I've Not Yet Tried When I first installed Windows I was given a choice between three types of partitions to use. I no longer remember what the choices were or what I selected. One was a GUID partition table, one was a traditional MBR, and I can't remember the third option.

    Read the article

  • HYPER-V R2 Can not mount ISO from network location (UNC Path)

    - by Entity_Razer
    So, as the name suggest I'm trying to mount a ISO from a network share using the UNC path to a HYPER-V R2 Cluster. This is a pure Demo / test case setup with: 2x HYPER-V R2 1X NAS/iSCSI CSV Cluster Management is happening through the MMC with RSAT tools. So what i've done so far is: Set up the cluster and configure Quorum, add CSV Shares and disks, set up 1 Virtual Machine on the Hyper-1 node. What i'm trying to do is, you go to settings --- DVD Drive --- use network location ---- Pick ISO file and press "apply". Error I'm getting is either "User account does not have rights to mount iso". I changed that or stopped getting that message when I went to the HYPER-V Node settings and tabbed on: "Use Default Credentials Automatically". Now I stopped getting the "user does not have right..." message but I get the following: Error applying DVD Drive Changes Failed to remove device microsoft synthetic DVD Drive:" the specified network resource or device is no longer available" I've google'd the problem but am unable to find a solution. Anyone here able to help me out ? Much abbliged !

    Read the article

  • Windows Server 2008 R2 DFSR Backlog Troubleshooting - Where to look for the cause of the problem?

    - by caleban
    Our target server indicates it has hundreds of thousands of backlogged transactions. Our authoritative source server indicates it has no backlogged transactions. No replication is taking place. Tests with plain text files aren't replicating. dfsdiag propogation tests fail to propogate. I've restarted the DFS services. I've restarted the servers. I've created new DFS shares to test with. The authoritative source server indicates it has no backlogs and the target indicates it has backlogs (which are the files it's waiting to receive). Files don't replicate in either direction. 2x Windows Server 2008 R2 Standard servers One server is at each of two sites The DFSR shares are on each respective server \site_1_server_1\users \site_2_server_1\users The sites are connected by a T1 DFSR worked for a week. I added a new share, another folder on the same servers, and that replicated for a weekend but never finished. Then all replication stopped. Is Windows DFSR flaky? What tools should I use and what should I look at to identify what's causing this problem?

    Read the article

  • DriveImage XML fails with a Windows Volume Shadow Service Error

    - by Ssvarc
    I'm trying to image a SATA laptop hard drive, using DriveImageXML, that is attached to my computer via a USB adapter. I'm running Win7 Ultimate 64 bit. DriveXML is returning: Could not initialize Windows Volume Shadow Service (VSS). ERROR C:\Program Files (x86)\Runtime Software\Drivelmage XML\vss64.exe failed to start. ERROR TIMEOUT Make sure VSSVC.EXE is running in your task manager. Click Help for more information. VSSVC.EXE is running in Task Manager, as is VSS64.exe. Looking at the FAQ on the Runtime webpage this turned up: Please verify in Settings-Control Panel-Administrative Tools-Services that the following services are enabled: MS Software Shadow Copy Provider Volume Shadow Copy Also make sure you are able to stop and start these services. Possible reasons for VSS failures: For VSS to work, at least one volume in your computer must be NTFS. If you use only FAT drives, VSS will not function. The required NTFS volume does not need to be identical with the volume you want to image. You should make sure that VSSVC.EXE is running in your task manager. If the problems persist, registering "oleaut.dll" and "oleaut32.dll" using "regsvr32" might help. Both of those services are running and can be started and stopped without issue. Using "regsvr32" to register ""oleaut32.dll" returns successful, but "oleaut.dll" returns: The module "oleaut.dll" failed to load. Make sure the binary is stored at the specified path or debug it to check for problems with the binary or dependent .DLL files. The specified module could not be found. Some other information that might be relevant. Browsing to the drive is successful, but accessing certain folders returns an "access" error. Windows runs a permissions adder that adds the current user profile to the NFTS permissions. Could this be the cause of the issue? DriveImage XML is running as Administrator. Thoughts?

    Read the article

  • yum update works but yum --security update fails to work in Fedora 12

    - by bobo
    I had already installed the yum-security before. And I was going to do an update by entering the following command: [root@localhost /]# yum update Loaded plugins: presto, priorities, refresh-packagekit, security Skipping security plugin, no data Setting up Update Process Resolving Dependencies Skipping security plugin, no data --> Running transaction check ---> Package eject.i686 0:2.1.5-17.fc12 set to be updated ---> Package glibc.i686 0:2.11.1-4 set to be updated ---> Package glibc-common.i686 0:2.11.1-4 set to be updated ---> Package glibc-devel.i686 0:2.11.1-4 set to be updated ---> Package glibc-headers.i686 0:2.11.1-4 set to be updated ---> Package gnome-themes.noarch 0:2.28.1-3.fc12 set to be updated ---> Package gtk2.i686 0:2.18.9-3.fc12 set to be updated ---> Package gtk2-immodule-xim.i686 0:2.18.9-3.fc12 set to be updated ---> Package kernel-PAE.i686 0:2.6.32.11-99.fc12 set to be installed ---> Package kernel-PAE-devel.i686 0:2.6.32.11-99.fc12 set to be installed ---> Package kernel-PAEdebug-devel.i686 0:2.6.32.11-99.fc12 set to be installed ---> Package kernel-debug-devel.i686 0:2.6.32.11-99.fc12 set to be installed ---> Package kernel-devel.i686 0:2.6.32.11-99.fc12 set to be installed ---> Package kernel-firmware.noarch 0:2.6.32.11-99.fc12 set to be updated ---> Package kernel-headers.i686 0:2.6.32.11-99.fc12 set to be updated ---> Package libnetfilter_conntrack.i686 0:0.0.101-1.fc12 set to be updated ---> Package media-player-info.noarch 0:5-1.fc12 set to be updated ---> Package nscd.i686 0:2.11.1-4 set to be updated ---> Package perf.noarch 0:2.6.32.11-99.fc12 set to be updated ---> Package rhythmbox.i686 0:0.12.6-5.fc12 set to be updated ---> Package sysvinit-tools.i686 0:2.87-3.dsf.fc12 set to be updated --> Finished Dependency Resolution --> Running transaction check ---> Package kernel-PAE.i686 0:2.6.31.12-174.2.3.fc12 set to be erased --> Finished Dependency Resolution Dependencies Resolved ================================================================================ Package Arch Version Repository Size ================================================================================ Installing: kernel-PAE i686 2.6.32.11-99.fc12 updates 20 M kernel-PAE-devel i686 2.6.32.11-99.fc12 updates 6.2 M kernel-PAEdebug-devel i686 2.6.32.11-99.fc12 updates 6.2 M kernel-debug-devel i686 2.6.32.11-99.fc12 updates 6.2 M kernel-devel i686 2.6.32.11-99.fc12 updates 6.1 M Updating: eject i686 2.1.5-17.fc12 updates 49 k glibc i686 2.11.1-4 updates 4.2 M glibc-common i686 2.11.1-4 updates 14 M glibc-devel i686 2.11.1-4 updates 953 k glibc-headers i686 2.11.1-4 updates 590 k gnome-themes noarch 2.28.1-3.fc12 updates 1.5 M gtk2 i686 2.18.9-3.fc12 updates 3.2 M gtk2-immodule-xim i686 2.18.9-3.fc12 updates 60 k kernel-firmware noarch 2.6.32.11-99.fc12 updates 968 k kernel-headers i686 2.6.32.11-99.fc12 updates 749 k libnetfilter_conntrack i686 0.0.101-1.fc12 updates 37 k media-player-info noarch 5-1.fc12 updates 32 k nscd i686 2.11.1-4 updates 189 k perf noarch 2.6.32.11-99.fc12 updates 79 k rhythmbox i686 0.12.6-5.fc12 updates 4.0 M sysvinit-tools i686 2.87-3.dsf.fc12 updates 58 k Removing: kernel-PAE i686 2.6.31.12-174.2.3.fc12 @updates 72 M Transaction Summary ================================================================================ Install 5 Package(s) Upgrade 16 Package(s) Remove 1 Package(s) Reinstall 0 Package(s) Downgrade 0 Package(s) Total download size: 75 M Is this ok [y/N]: But then I changed my mind, I decided to do a security-only update instead of a full update, so I entered the following command: [root@localhost /]# yum --security update Loaded plugins: presto, priorities, refresh-packagekit, security Setting up Update Process Resolving Dependencies Limiting packages to security relevant ones http://download.fedoraproject.org/pub/fedora/linux/updates/12/i386/repodata/updateinfo.xml.gz: [Errno 14] HTTP Error 416 : http://ftp.cuhk.edu.hk/pub/linux/fedora/updates/12/i386/repodata/updateinfo.xml.gz Trying other mirror. http://ftp.cuhk.edu.hk/pub/linux/fedora/updates/12/i386/repodata/updateinfo.xml.gz: [Errno 14] HTTP Error 416 : http://ftp.cuhk.edu.hk/pub/linux/fedora/updates/12/i386/repodata/updateinfo.xml.gz Trying other mirror. http://ftp.riken.jp/Linux/fedora/updates/12/i386/repodata/updateinfo.xml.gz: [Errno 14] HTTP Error 416 : http://ftp.riken.jp/Linux/fedora/updates/12/i386/repodata/updateinfo.xml.gz Trying other mirror. http://mirror.cse.iitk.ac.in/fedora/updates/12/i386/repodata/updateinfo.xml.gz: [Errno 14] HTTP Error 416 : http://mirror.cse.iitk.ac.in/fedora/updates/12/i386/repodata/updateinfo.xml.gz Trying other mirror. http://mirrors.isu.net.sa/pub/fedora/linux/updates/12/i386/repodata/updateinfo.xml.gz: [Errno 14] HTTP Error 416 : http://mirrors.isu.net.sa/pub/fedora/linux/updates/12/i386/repodata/updateinfo.xml.gz Trying other mirror. ftp://ftp.chu.edu.tw/linux/Fedora/linux/updates/12/i386/repodata/updateinfo.xml.gz: [Errno -1] Metadata file does not match checksum Trying other mirror. http://mirror.yandex.ru/fedora/linux/updates/12/i386/repodata/updateinfo.xml.gz: [Errno 14] HTTP Error 416 : http://mirror.yandex.ru/fedora/linux/updates/12/i386/repodata/updateinfo.xml.gz Trying other mirror. http://linus.iyte.edu.tr/linux/fedora/linux/updates/12/i386/repodata/updateinfo.xml.gz: [Errno 14] HTTP Error 416 : http://linus.iyte.edu.tr/linux/fedora/linux/updates/12/i386/repodata/updateinfo.xml.gz Trying other mirror. http://ftp.jaist.ac.jp/pub/Linux/Fedora/updates/12/i386/repodata/updateinfo.xml.gz: [Errno 14] HTTP Error 416 : http://ftp.jaist.ac.jp/pub/Linux/Fedora/updates/12/i386/repodata/updateinfo.xml.gz Trying other mirror. http://ftp.kddilabs.jp/Linux/packages/fedora/updates/12/i386/repodata/updateinfo.xml.gz: [Errno 14] HTTP Error 416 : http://srv2.ftp.ne.jp/Linux/packages/fedora/updates/12/i386/repodata/updateinfo.xml.gz Trying other mirror. http://www.ftp.ne.jp/Linux/distributions/fedora/updates/12/i386/repodata/updateinfo.xml.gz: [Errno 14] HTTP Error 416 : http://srv2.ftp.ne.jp/Linux/distributions/fedora/updates/12/i386/repodata/updateinfo.xml.gz Trying other mirror. http://ftp.rhd.ru/pub/fedora/linux/updates/12/i386/repodata/updateinfo.xml.gz: [Errno 14] HTTP Error 416 : http://ftp.rhd.ru/pub/fedora/linux/updates/12/i386/repodata/updateinfo.xml.gz Trying other mirror. http://mirrors.163.com/fedora/updates/12/i386/repodata/updateinfo.xml.gz: [Errno 14] HTTP Error 416 : http://mirrors.163.com/fedora/updates/12/i386/repodata/updateinfo.xml.gz Trying other mirror. http://mirror.nus.edu.sg/fedora/updates/12/i386/repodata/updateinfo.xml.gz: [Errno 14] HTTP Error 416 : http://mirror.nus.edu.sg/fedora/updates/12/i386/repodata/updateinfo.xml.gz Trying other mirror. http://ftp.yz.yamagata-u.ac.jp/pub/linux/fedora/linux/updates/12/i386/repodata/updateinfo.xml.gz: [Errno 14] HTTP Error 416 : http://ftp.yz.yamagata-u.ac.jp/pub/linux/fedora/linux/updates/12/i386/repodata/updateinfo.xml.gz Trying other mirror. http://ftp.linux.org.tr/fedora/updates/12/i386/repodata/updateinfo.xml.gz: [Errno 14] HTTP Error 416 : http://ftp.linux.org.tr/fedora/updates/12/i386/repodata/updateinfo.xml.gz Trying other mirror. http://mirrors.cytanet.com.cy/linux/fedora/linux/updates/12/i386/repodata/updateinfo.xml.gz: [Errno 14] HTTP Error 416 : http://mirrors.cytanet.com.cy/linux/fedora/linux/updates/12/i386/repodata/updateinfo.xml.gz Trying other mirror. http://fedoramirror.hnsdc.com/updates/12/i386/repodata/updateinfo.xml.gz: [Errno 14] HTTP Error 416 : http://fedoramirror.hnsdc.com/updates/12/i386/repodata/updateinfo.xml.gz Trying other mirror. http://ftp.twaren.net/Linux/Fedora/linux/updates/12/i386/repodata/updateinfo.xml.gz: [Errno 14] HTTP Error 416 : http://c147.twaren.net/pub/Linux/Fedora/linux/updates/12/i386/repodata/updateinfo.xml.gz Trying other mirror. http://ftp.mirror.tw/pub/fedora/linux/updates/12/i386/repodata/updateinfo.xml.gz: [Errno 14] HTTP Error 416 : http://ftp.mirror.tw/pub/fedora/linux/updates/12/i386/repodata/updateinfo.xml.gz Trying other mirror. http://ftp.cs.pu.edu.tw/Linux/Fedora/updates/12/i386/repodata/updateinfo.xml.gz: [Errno 14] HTTP Error 416 : http://ftp.cs.pu.edu.tw/Linux/Fedora/updates/12/i386/repodata/updateinfo.xml.gz Trying other mirror. http://ubuntu.cn99.com/fedora/updates/12/i386/repodata/updateinfo.xml.gz: [Errno 14] HTTP Error 416 : http://ubuntu.cn99.com/fedora/updates/12/i386/repodata/updateinfo.xml.gz Trying other mirror. Error: failure: repodata/updateinfo.xml.gz from updates: [Errno 256] No more mirrors to try. You could try using --skip-broken to work around the problem ^C[root@localhost /]# As it can be seen in the output, when I run the yum --security update command, it did show the Limiting packages to security relevant ones message so it's aware of the option. But I don't know why it keeps reporting the http error 416. I searched in google and found the following description of the error but it doesn't seem to help much. HTTP ERROR 416 - Requested Range Not Satisfiable A 416 status code indicates that the server was unable to fulfill the request. This may be, for example, because the client asked for the 800th-900th bytes of a document, but the document was only 200 bytes long. It suggests me to use the --skip-broken option, I tried and the output is the same. I already tested many times, it just doesn't work when the --security option is used. What could be the possible cause for this problem?

    Read the article

  • Managing scalability and availability with two servers running Apache Httpd, Apache Mina and MySQL

    - by celalo
    Hello, I am not a developer and I don't much experience with scalable server architectures. But I am in need of a highly available and scalable system for one of my projects. There is going to be two servers I am going to use for the time being. Both with 4 core CPUs and 8 GB RAM with RAID structures running CentOS 5.4. I will also have feature called "Failover IP" which enables to direct an IP address to another server within short time. The applications which will be run on the servers: There is going to be a Java application based on Apache Mina server for handling TCP requests from some hundreds of network devices where the devices are going to send request as much as one request per minute. Handling those requests, includes parsing the requests and inserting a few rows to the Database. Parsing requests before inserting data to the DB does take neglectable time. There is going to be MySQL server, as I stated above. Also there is going to be a PHP web application running on Apache Httpd Server which uses the same DB with the Java application. What I wish to have is to make use of those two servers at the most. I was imagining to have the servers identical, sharing the work load. MySQL could be a cluster maybe? And if some application fails or the whole machine goes down, the other will continue serving the requests seamlessly. Reminding that a "Failover IP" feature will be available for me to take advantage of. Also, It should be kept in mind that number of servers could increase in time, to meet the demand. What can you suggest? Which kind of tools I can make use of? Which kind of monitoring software (paid/unpaid) I have? Thanks in advance.

    Read the article

  • SSL certificate on IIS 7

    - by comii
    I am trying to install a SSL certificate on IIS 7. I have download a free trial certificate. After that, this is the steps what I do: Click the Start menu and select Administrative Tools. Start Internet Services Manager and click the Server Name. In the center section, double click on the Server Certificates button in the Security section. From the Actions menu click Complete Certificate Request. Enter the location for the certificate file. Enter a Friendly name. Click OK. Under Sites select the site to be secured with the SSL certificate. From the Actions menu, click Bindings.This will open the Site Bindings window. In the Site Bindings window, click Add. This opens the Add Site Binding window. Select https from the Type menu. Set the port to 443. Select the SSL Certificate you just installed from the SSL Certificate menu. Click OK. This is the step where I get the message: One or more intermediate certificates in the certificate chain are missing. To resolve this issue, make sure that all of intermediate certificates are installed. For more information, see http://support.microsoft.com/kb/954755 After this, when I access the web site on its first page, I get this message: There is a problem with this website's security certificate. What am I doing wrong?

    Read the article

  • Android SDK emulator freezes on a Mac running OS X 10.6 Snow Leopard

    - by Donald Burr
    I'm having trouble running the Android SDK on both of my Macs running OS X 10.6.2 Snow Leopard. This appears to be a 64 bit vs. 32 bit issue, as Snow Leopard now defaults to 64-bit everything, including the Java virtual machine. I found this webpage with instructions on how to get the Android tools to run in the 32-bit Java VM, and I am now able to run the Android GUI tool to download SDK files, create AVM's, etc. However, when I try the Hello World tutorial and get to the point where I run my application under the Android emulator, everything goes south. The emulator appears to start but it hangs (spinning beachball of death cursor) without displaying anything. (This only hangs the emulator; the rest of the system still works fine.) If I follow the exact same steps (minus the 32-bit java hack) in a Windows virtual machine, everything works fine. Googling didn't yield anything useful (except for the 32-bit java hack I spoke of earlier). This occurs on both my Mac Pro tower and 13" MacBook Pro. Does anyone have any suggestions?

    Read the article

  • How to use Salt Stack with minions all behind NAT (not publicly accessible, default salt ports not open)?

    - by MountainX
    Can Salt Stack minions communicate with the salt master from behind NAT/Firewalls, etc., using standard ports that would be open be default in all consumer NAT routers (and without the minions having a public DNS record or static IP)? I'm working my way through my first salt tutorial, and this is where I'm stuck. I am able to configure iptables on the Ubuntu salt-master. But I have no control over the routers/NAT that the minions will sit behind. So far I tried these settings: /etc/salt/master: publish_port: 465 ret_port: 443 /etc/salt/minion: master_port: 465 That did not work. Background: I have a custom developed application presently running on about 40 Kubuntu laptops (& more planned). Every few months I have to update the application. (Often this just amounts to replacing a .jar file, which requires root permissions.) I also have to run Ubuntu updates and a few other minor things. I've been doing it manually, one by one, using Team Viewer to log into each client. I would like to dramatically improve this process. The two options I'm aware of are either: use reverse ssh tunnels and bash scripts. I tested this and it works. But I don't get any of the reporting, etc., I would get with Salt Stack. use Salt Stack (or similar) management tool. But I need a really simple tool. I can't invest any time in a big learning curve. I looked at Puppet and a bunch of related tools. The only one I found that looked simple enough for me (so far) was Salt Stack. But I'm stuck now because my minion can't reach the salt-master, as stated above. I appreciate suggestions.

    Read the article

  • pGina with automatic Kerberos ticket and OpenAFS token/ticket

    - by rolands
    I am currently updating our educational Windows lab images from XP to 7, In doing so we are also migrating from Comtarsia to pGina. Unfortunately somewhere in the transition our automation that fetched kerberos and OpenAFS tickets/tokens on login has completely stopped functioning. Basically what used to happen was, using kfw-3.2.2 and the old OpenAFS release (loopback adapter days), either comtarsia would share password or something with the NIM (Network Identity Manager) which would authenticate against the kerberos server gaining a ticket and AFS token needed to access the users file, this was aided by the fact that our ldap database that windows authenticates against is also what kerberos uses to authenticate so usernames/passwords are the same across both services. I have set up all of the tools, albeit newer 64bit versions which seem to have given me less trouble than the previous releases of NIM/OpenAFS/Krb5, as well as setting their configurations back to what we used to use. Unfortunately this seems to be fubar'd in some way, instead all we get now is a OpenAFS token, most likely I assume from the AFScreds tool which operates some kind of integrated login process, although this does not help in getting a kerberos ticket or a afs ticket for which a login box is provided be NIM after the user logs in. Does anyone know IF it is possible to do what we are trying, and if so how? I was considering writing a pGina plugin which would interact with the server itself but this seems slightly like overkill considering that all these applications already exist...

    Read the article

  • Accessing network shares on Windows7 via SonicWall VPN client

    - by Jack Lloyd
    I'm running Windows7 x64 (fully patched) and the SonicWall 4.2.6.0305 client (64-bit, claims to support Windows7). I can login to the VPN and access network resources (eg SSH to a machine that lives behind the VPN). However I cannot seem to be able to access shared filesystems. Windows is refusing to do discovery on the VPN network. I suspect part of the problem is Windows persistently considers the VPN connection to be a 'public network'. Normally, you can open the network and sharing center and modify this setting, however it does not give me a choice for the VPN. So I did the expedient thing and turned on file sharing for public networks. I also disabled the Windows firewall for good measure. Still no luck. I can access the server directly by putting \\192.168.1.240 in the taskbar, which brings up the list of shares on the server. However, trying to open any of the shares simply tells me "Windows cannot access \\192.168.1.240\share You do not have permission to access ..."; it never asks for a domain password. I also tried Windows7 native VPN functionality - it couldn't successfully connect to the VPN at all. I suspect this is because SonicWall is using some obnoxious special/undocumented authentication system; I had similar problems trying to connect on Linux with the normal IPsec tools there. What magical invocation or control panel option am I missing that will let this work? Are there any reasonable debugging strategies? I'm feeling quite frustrated at Windows tendency to not give me much useful information that might let me understand what it is trying to do and what is going wrong.

    Read the article

  • Fedora 13 - No module named yum

    - by drozzy
    This is driving me bananas! After a recent update in Fedora 13 64bit, my yum is gone: $> yum update There was a problem importing one of the Python modules required to run yum. The error leading to this problem was: No module named yum Please install a package which provides this module, or verify that the module is installed correctly. I tried looking for an RPM yum package - to install yum. I went to the Fedora site: http://fedoraproject.org/wiki/Tools/yum Call me blind but I cannot find it anywhere on that page! Most of the solutions suggest repairing yum... with yum! But I don't have yum? Yum yum yum? :< Any help? Here are some outputs for rpm commands: $> rpm -ql python | grep "site-packages$" /usr/lib/python2.6/site-packages /usr/lib64/python2.6/site-packages $> rpm -ql yum | grep "site-packages/yum$" /usr/lib/python2.6/site-packages/yum

    Read the article

  • What is there in Win 7 Pro (or Ultimate) that is not there in Home Premium? - Especially considering this situation..

    - by Senthil
    I want to know the REAL difference between Windows 7 Home Premium and Professional/Utimate. In India, the cost of different versions: Ultimate - 11,200 INR Professional - 10,700 INR Home Premium - 6,600 INR The absolute cost of the first two is so high to me that the difference (500 INR) doesn't matter. So to me there is really no choice between the first two - If I decide to buy the Professional version, I'd rather go for Ultimate itself. What I want to know is, whether Home Premium is enough for my needs. I tried searching for comparison but many look like just marketing junk from MS. They are short and vague. According to this page, the major differences between Pro and HomePremium are Run many Windows XP productivity programs in Windows XP Mode. Connect to company networks easily and more securely with Domain Join. You can do both in Pro but not in Home Premium. I intend to use my Windows 7 for a small business - just starting up. So I'll be dealing with the following: All kinds of development tools, servers Very important - I will run Virtual Machine Software (MS VPC or VMWare or Sun VirtualBox etc..) My system will be acting as the server for most purposes till I can afford dedicated servers. Connect the system to a variety of network devices (PCs, Printers, etc..) Run productivity, business and financial apps Any other small software startup business requirement that I haven't thought of yet. Professional (and Ultimate) is twice as expensive as Home Premium. So it'd be great if someone can point out the things you cannot do with Home Premium, when you use it like I explained above, so that I can make a decision about which one to buy. I need some real-life experiences so that I can make an informed decision - not a decision based on marketing junk.

    Read the article

  • Ant task to pre-compile JSPs on weblogic server

    - by user24560
    I am trying to create an ant task to compile JSPs. Here are the excerpts from the build.xml related to the task: .... <fileset dir="${java.home}/lib"> <include name="tools.jar"/> </fileset> <java classname="weblogic.jspc" fork="yes"> <classpath refid="weblogic.jsp.classpath" /> <sysproperty key="weblogic.jsp.windows.caseSensitive" value="false"/> <arg line="-forceGeneration -keepgenerated -compileAll -webapp ${jsp.src.dir} -d ${jsp.generated.src.dir}"/> </java> When I try to run wl.jsp.generate task, I get: wl.jsp.generate: [java] [jspc] warning: expected file /WEB-INF/web.xml not found, tag libraries cannot be resolved. [java] [jspc] Overriding default descriptor option 'keepgenerated' with value specified on command-line 'true' [java] Exception encountered while compiling C:\workspace\smcmw\smcmw_browser\jsp\smcesearchprogress.jsp [java] java.lang.NoSuchMethodError: javax.servlet.jsp.tagext.TagAttributeInfo.(Ljava/lang/String;ZLjava/lang/String;ZZLjava/lang/String;ZZLjava/lang/String;Ljava/lang/String;)V [java] at weblogic.jsp.internal.jsp.tag.TagAttrInfoEx.<init>(TagAttrInfoEx.java:64) [java] at weblogic.jsp.internal.jsp.tag.TagAttrInfoEx.<init>(TagAttrInfoEx.java:57) [java] at weblogic.jsp.internal.jsp.tag.TagAttrInfoEx.<init>(TagAttrInfoEx.java:41) [java] at weblogic.jsp.internal.jsp.tag.TagAttrInfoEx.read(TagAttrInfoEx.java:86) Looks like it fails because it can't find WEB-INF/web.xml file and tag libraries. How can I fix this?

    Read the article

  • MSSQL 2000 installation error: Setup failed to configure the server. Refer to the server error logs.

    - by kaneuniversal
    I'm trying to install MSSQL 2000 on a virtual Windows 2003 instance. However, every time I run the install program, it fails to start the service. This is the error log: 21:46:50 C:\Program Files\Microsoft SQL Server\80\Tools\Binn\cnfgsvr.exe -F "C:\WINDOWS\sqlstp.log" -I MSSQLSERVER -V 1 -M 0 -Q "SQL_Latin1_General_CP1_CI_AS" -H 131408 -U sa -P ############################################################################### Starting Service ... SQL_Latin1_General_CP1_CI_AS -m -Q -T4022 -T3659 Connecting to Server ... driver={sql server};server=xxxxxxxxxx;UID=sa;PWD=;database=master [Microsoft][ODBC SQL Server Driver]Timeout expired driver={sql server};server=xxxxxxxxxx;UID=sa;PWD=;database=master [Microsoft][ODBC SQL Server Driver]Timeout expired driver={sql server};server=xxxxxxxxxx;UID=sa;PWD=;database=master [Microsoft][ODBC SQL Server Driver]Timeout expired SQL Server configuration failed. ############################################################################### 21:49:34 Process Exit Code: (-1) 22:19:04 Setup failed to configure the server. Refer to the server error logs and C:\WINDOWS\sqlstp.log for more information. 22:19:04 Action CleanUpInstall: 22:19:04 C:\DOCUME~1\ADMINI~1\LOCALS~1\Temp\1\SqlSetup\Bin\scm.exe -Silent 1 -Action 4 -Service SQLSERVERAGENT 22:19:05 Process Exit Code: (1060) The specified service does not exist as an installed service. 22:19:05 C:\DOCUME~1\ADMINI~1\LOCALS~1\Temp\1\SqlSetup\Bin\scm.exe -Silent 1 -Action 4 -Service MSSQLSERVER 22:19:05 Process Exit Code: (0) 22:19:05 StatsGenerate returned: 2 22:19:05 StatsGenerate (0x0,0x1,0xf00000,0x200,1033,303,0x0,0x1,0,0,0 22:19:05 StatsGenerate -1,Administrator) 22:19:05 Installation Failed. Has anyone had this problem? Any ideas about how to fix it? Thanks very much, Michael

    Read the article

  • Explain why folder's permissions differ depending on HOW user is accessing server AFP vs SSH

    - by Meltemi
    Hoping someone can explain what is probably fairly obvious...but confuses me. Imagine two users with admin privileges on our server (Mac OS X Server 10.5). Call them joe & bob. both users are members of these groups: Staff Group ID: 20 Workgroup Group ID: 1025 Shared folder "devfolder" has sharing set as so: POSIX: Owner: joe read & write Group: admin read & write Other no access ACL: Workgroup Allow Read & write Question is why when looking at same folder does the ownership appear to change depending on who's doing the looking?!? Both looking at same folder on the server: From Joe's perspective: xserve:devfolder joe$ ls -l drwxrwxr-x 6 joe workgroup 204 May 20 19:32 app drwxrwxr-x 9 joe workgroup 306 May 20 19:32 config drwxrwxr-x 3 joe workgroup 102 May 20 19:32 db drwxrwxr-x 3 joe workgroup 102 May 20 19:32 doc drwxrwxr-x 3 joe workgroup 102 May 20 19:32 lib And from Bob's perspective (folder mounted on his machine via AFP): bobmac:devfolder bob$ ls -l drwxrwxr-x 6 bob _bob 264 May 20 19:32 app drwxrwxr-x 9 bob _bob 264 May 20 19:32 config drwxrwxr-x 3 bob _bob 264 May 20 19:32 db drwxrwxr-x 3 bob _bob 264 May 20 19:32 doc drwxrwxr-x 3 bob _bob 264 May 20 19:32 lib Now if Bob connects to server via SSH then his output is identical to Joe's, as expected. Can anyone tell me what the client is doing in this case and what should be expected when bob creates or updates files in this folder? What tools do I have to better understand this from the command line? Is this normal? Perhaps a "cleaner" way that wouldn't be confusing with "bob _bob"?!?

    Read the article

  • How to easily input and display isolated japanese radicals on MacOS X?

    - by ogerard
    (This question was considered as off-topic on Japanese.SE and more suitable for SuperUser). I like to write computer notes about what I learn in Japanese. From time to time, I would like to be able to include in my text a given radical, say kokoro ?, which takes several graphic forms when used as an element in a more complex kanji, for instance . I did not succeed on my system (Mac OS X 10.7) to find the glyphs for these variants conveniently and exactly as I would like them (I would also be interested about how to do this on Windows 7 or Linux). I first tried the name of the kanji from which the radical is derived. Then I tried to use the japanese name for them, such as risshinben (as in ?) and shitagokoro (as in ?), hoping that the hiragana or katakana input would recognize them and propose me their representation, but it did not work. So I looked into the Full Japanese Character Table, under the "by radical" tab, and found at least a version of each of them : ? (CJK 5FC4) and ? (CJK 38FA) with the correct kun readings. I have them now as favorites but do I need to do that for all radicals? Do I need to register all of them in a user dictionary? I would imagine that I am not the only one who wants to do use them. Besides, the versions I have found are not suited for all occasions: they are centered on a standard kanji square. If I want them to appear near to a placeholder, or demonstrate their proportion to the rest of a typical kanji, I have to make complicated adjustments, depending on my use and the kind of radical. More generally are there computer tools for japanese dictionary editors and japanese teachers I could use on Mac OS X? (I could not add relevant tags such as : japanese or ideogram, please feel free to edit)

    Read the article

< Previous Page | 415 416 417 418 419 420 421 422 423 424 425 426  | Next Page >