Search Results

Search found 12193 results on 488 pages for 'odi technical feature overviews'.

Page 441/488 | < Previous Page | 437 438 439 440 441 442 443 444 445 446 447 448  | Next Page >

• Is it possible to repair a Cisco 3500 XL (3548) switch with POST Error messages?

  - by Alex

  I've got an old Cisco 3500 XL, and it seems to have hardware issues. I've loaded the latest IOS and cleared all config. Does anyone have any experience fixing the switch core? I'm a reasonably competent SMD solderer, can I replace/reflow some chips? I've checked the power supply voltages and it's all within tolerance, and no visible signs of any component damage. Some chips are hot to the touch. I understand that these were EOL as of 2007, but should have a lifetime warranty for the electronics. I don't have a Cisco support contract, so I can't file a ticket. What should I do? Console output: switch: dir flash: Directory of flash:/ 2 -rwx 1811584 <date> c3500xl-c3h2s-mz.120-5.WC17.bin 1799680 bytes available (1812992 bytes used) switch: boot Loading "flash:c3500xl-c3h2s-mz.120-5.WC17.bin"...################################################################################################################################################################################### File "flash:c3500xl-c3h2s-mz.120-5.WC17.bin" uncompressed and installed, entry point: 0x3000 executing... Restricted Rights Legend Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (c) of the Commercial Computer Software - Restricted Rights clause at FAR sec. 52.227-19 and subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at DFARS sec. 252.227-7013. cisco Systems, Inc. 170 West Tasman Drive San Jose, California 95134-1706 Cisco Internetwork Operating System Software IOS (tm) C3500XL Software (C3500XL-C3H2S-M), Version 12.0(5)WC17, RELEASE SOFTWARE (fc1) Copyright (c) 1986-2007 by cisco Systems, Inc. Compiled Tue 13-Feb-07 15:04 by antonino Image text-base: 0x00003000, data-base: 0x00352924 Initializing C3500XL flash... flashfs[1]: 1 files, 1 directories flashfs[1]: 0 orphaned files, 0 orphaned directories flashfs[1]: Total bytes: 3612672 flashfs[1]: Bytes used: 1812992 flashfs[1]: Bytes available: 1799680 flashfs[1]: flashfs fsck took 3 seconds. flashfs[1]: Initialization complete. ...done Initializing C3500XL flash. C3500XL POST: System Board Test: Passed C3500XL POST: Daughter Card Test: Passed C3500XL POST: CPU Buffer Test: Passed C3500XL POST: CPU Notify RAM Test: Passed C3500XL POST: CPU Interface Test: Passed C3500XL POST: Testing Switch Core: Passed Error with Switch Core BIST test Phase 0. Returns: Test Complete Low : 0x0FFFFFFF, Test Complete High : 0xFFFFFFFE Test Phase Low : 0x00000040, Test Phase High : 0x00000000 Test Phase Third : 0x00000000, Test Complete Third : 0x000001F8 C3500XL POST FAILURE: Testing Switch Core: Failed C3500XL POST FAILURE: Testing Buffer Table: Failed C3500XL POST FAILURE: Data Buffer Test: Failed C3500XL POST FAILURE: Configuring Switch Parameters: Failed C3500XL POST FAILURE: Switch Core BIST failed. C3500XL POST FAILURE: Cannot test Modules due to failure of Switch Core POST Del Mar Failure (0th Del Mar): req system failed to init C3500XL POST FAILURE: C3500XL POST FAILURE: ATM: required system failed to init C3500XL POST: Ethernet Controller Test: Passed C3500XL POST FAILURE: MII Test: Failed C3500XL POST FAILURE: Error waiting for Ethernet Controller and SW_PARAMS C3500XL POST FAILURE: Initialization/POST failed C3500XL POST FAILURE: AT: Failing because system POST failed Exception (8192)! Debug Exception (Could be NULL pointer dereference) CPU Register Context: Vector = 0x00002000 PC = 0x000F36F4 MSR = 0x00029200 CR = 0x22000024 LR = 0x000F6964 CTR = 0x001DE46C XER = 0x00000000 R0 = 0x00000000 R1 = 0x004E2580 R2 = 0x00000000 R3 = 0x00000000 R4 = 0x00000001 R5 = 0x00000000 R6 = 0x004E2718 R7 = 0x004E2718 R8 = 0x00000008 R9 = 0x00000000 R10 = 0x0000FFFF R11 = 0x00480000 R12 = 0x42000024 R13 = 0x00000000 R14 = 0x00000000 R15 = 0x00000000 R16 = 0x00000000 R17 = 0x00000000 R18 = 0x00000000 R19 = 0x00000000 R20 = 0x00000000 R21 = 0x00000000 R22 = 0x00000000 R23 = 0x00000000 R24 = 0x00000000 R25 = 0x00000020 R26 = 0x004E2718 R27 = 0x004E2718 R28 = 0x00000020 R29 = 0x00002513 R30 = 0x00000001 R31 = 0x00000000 Stack trace: PC = 0x000F36F4, SP = 0x004E2580 Frame 00: SP = 0x004E25A0 PC = 0x40000016 Frame 01: SP = 0x004E2618 PC = 0x000F6964 Frame 02: SP = 0x004E26A8 PC = 0x000F76DC Frame 03: SP = 0x004E26C8 PC = 0x000E8114 Frame 04: SP = 0x004E26F0 PC = 0x001F5BF8 Frame 05: SP = 0x004E2710 PC = 0x001F5CF4 Frame 06: SP = 0x004E2748 PC = 0x0023F4DC Frame 07: SP = 0x004E2750 PC = 0x0023E650 Frame 08: SP = 0x004E27C8 PC = 0x0023E89C Frame 09: SP = 0x004E27E0 PC = 0x0028AF34 Frame 10: SP = 0x004E27E8 PC = 0x001E38F8 Frame 11: SP = 0x004E2808 PC = 0x001E39A8 Frame 12: SP = 0x004E2820 PC = 0x0014E220 Frame 13: SP = 0x004E28C8 PC = 0x0014E39C Frame 14: SP = 0x00000000 PC = 0x001EB510

  Read the article

• WinXP - Having trouble sharing internet with 3G USB modem via ICS

  - by Carlos Nunez

  all! I've been banging my head against a wall with this issue for a few days now and am hoping someone can help out. I recently signed up for T-Mobile's webConnect 3G/4G service to replace the faltering (and slow) DSL connection in my apartment. The goal was to put the SIM in one of my old phones and use its built-in WLAN tethering feature to share Internet out to rest of my computers. I quickly found out that webConnect-provisioned SIMs do not work with regular smartphones, so I was forced to either buy a 4G-compatible router or tether one of my old laptops to my wireless router and share out that way. I chose the latter, and it's sharpening my inner masochistic self by the day. Here's the setup: GSM USB modem (via hub), ICS host - 10/100 Mbps Ethernet NIC, ICS "guest" - WAN port of my SMC WGBR14N wireless router in bridged mode (i.e. wireless access point). Ideally, this would make my laptop the DHCP server and internet gateway with the WAP giving everyone wireless coverage. I can browse internet on the host laptop fine. However, when clients try to connect, they get a DHCP-assigned IP from the laptop and are able to use the Internet for a few minutes before completely dying. After that happens, they are able to re-associate with the WAP and get IP addresses, but are unable to use Internet or resolve IP addresses until the laptop and router are restarted. If they do get access, it's very, very slow. After running Wireshark on the host machine, it turns out that this is because every TCP connection keeps getting RST. DNS seems to work. I would normally think the firewall is the culprit here, but when it drops packets, it drops them completely. The fact that TCP connections are being ACK'ed by the destination rules that out. Of course, none of the event Log isn't saying anything about what's going on. I also tried disabling power management on the NIC, since that's caused problems in the past; that didn't help either. I finally disabled receive-side scaling as per a Microsoft KB (that applied to Windows Server 2003, SP2) to no avail. I'm thinking of trying it with a different NIC (will be tough; don't have a spare Ethernet NIC around for the laptop), but I'm getting the impression that this simply doesn't work. Can anyone please advise? I apologise for the length of this post; all contributions are much appreciated! -Carlos.

  Read the article

• Moved DNS and Email Hosting, Now Can't Send/Receive To/From Domains Hosted on Previous Host

  - by maxfinis

  Our company had 4 domains whose emails and DNS were hosted by one company, and then we moved the email and DNS hosting for 3 of the 4 domains to a new company. Now, the 3 domains that were moved can't send or receive emails to and from the one domain still left on the old server. All other email functions work fine for all 4 domains. There are no bouncebacks, error messages, or emails stuck in queue, and no evidence of these missing emails hitting the new servers. The new hosting company confirms that everything is fine on their end, and assures me that it's most likely an old zone file still remaining on the old nameserver, and so the emails sent from the old host is routed to what it believes is still the authoritative nameserver. Because the old zone file's MX records still contain the old resource, the requests never leave the old nameserver to go online to do a fresh search for the real (new) authoritative nameserver. The compounding problem is that the old company is rather inept and doesn't seem to have the technical expertise to identify the problem, much less fix it. (I know, I know.) Is the problem truly that this old zone file just needs to be deleted from the old company's nameserver? If so, what's the best way for me to describe this to them? If not, what do you think could be the issue? Any help is much appreciated. I'm not in IT, so all this is new to me. I know it seems weird for me (the client) to have to do this legwork, but I just want to get this resolved. Here's what I've done: Ran dig to verify that the old server's MX records still point to the old authoritative server, instead of going online to do a fresh search: ~$ dig @old.nameserver.com domainthatwasmoved.com mx ; << DiG 9.6.0-APPLE-P2 << @old.nameserver.com domainThatWasMoved.com mx ; (1 server found) ;; global options: +cmd ;; Got answer: ;; -HEADER<<- opcode: QUERY, status: NOERROR, id: 61227 ;; flags: qr aa rd ra; QUERY: 1, ANSWER: 1, AUTHORITY: 0, ADDITIONAL: 1 ;; QUESTION SECTION: ;domainthatwasmoved.com. IN MX ;; ANSWER SECTION: domainthatwasmoved.com. 3600 IN MX 10 mail.oldmailserver.com. ;; ADDITIONAL SECTION: mail.oldmailserver.com. 3600 IN A 65.198.191.5 ;; Query time: 29 msec ;; SERVER: 65.198.191.5#53(65.198.191.5) ;; WHEN: Sun Dec 26 16:59:22 2010 ;; MSG SIZE rcvd: 88 Ran dig to try to see where the new hosting company's servers look when emails are sent from the 3 domains that were moved, and got refused: ~$ dig @new.nameserver.net domainStillAtOldHost.com mx ; << DiG 9.6.0-APPLE-P2 << @new.nameserver.net domainStillAtOldHost.com mx ; (1 server found) ;; global options: +cmd ;; Got answer: ;; -HEADER<<- opcode: QUERY, status: REFUSED, id: 31599 ;; flags: qr rd; QUERY: 1, ANSWER: 0, AUTHORITY: 0, ADDITIONAL: 0 ;; WARNING: recursion requested but not available ;; QUESTION SECTION: ;domainStillAtOldHost.com. IN MX ;; Query time: 31 msec ;; SERVER: 216.201.128.10#53(216.201.128.10) ;; WHEN: Sun Dec 26 17:00:14 2010 ;; MSG SIZE rcvd: 34

  Read the article

• 401 - Unauthorized On Server 2008 R2 IIS 7.5

  - by mxmissile

  I have a web application deployed to Server 2008 IIS 7.5 box. From remote it gives this error: 401 - Unauthorized: Access is denied due to invalid credentials. (remote = desktops on the same LAN) Have tried several remote clients using different browsers, all the same result. (IE, FF, and Chrome) Hitting the application from the desktop of the server itself works flawlessly. However I have not tried Firebug on the server desktop. I would assume it's still issuing a 401 status code yet returning the content anyway. See Update #2. The application is using Anonymous Authentication. The application is written in .NET 4.0 Asp.Net using the MVC framework. Static content works fine, example: http://server.com/content/image.jpg Sysinternals procmon returns these 2 results for each request: FAST IO DISALLOWED and PATH NOT FOUND. I have 2 other MVC apps running fine on the same server. I have checked the security on the folders and they all match. App runs fine on a Server 2008 IIS 7.0 box. Nothing shows up in the Event log on the server related to this. Pulling my hair out here, any troubleshooting tips? UPDATE #1: This just get's more WTF as I dig. If I click on the Application in IIS Manager - Error Pages - Edit Feature Settings select Detailed Errors, the app works remotely. Not leaving this on, so problem is not solved yet, its just more confusing. UPDATE #2: Using Firebug, I see that the Status is still 401 Unauthorized, but the Response is returning the application's correct HTML. UPDATE #3 Playing around with Failed Request Tracing, here is the WARNING Request Trace that is causing the 401: ModuleName ManagedPipelineHandler Notification 128 HttpStatus 401 HttpReason Unauthorized HttpSubStatus 0 ErrorCode 0 ConfigExceptionInfo Notification EXECUTE_REQUEST_HANDLER ErrorCode The operation completed successfully. (0x0) Update #4 Regular IIS log is showing this: #Software: Microsoft Internet Information Services 7.5 #Version: 1.0 #Date: 2010-07-20 19:17:22 #Fields: date time s-ip cs-method cs-uri-stem cs-uri-query s-port cs-username c-ip cs(User-Agent) sc-status sc-substatus sc-win32-status time-taken 2010-07-20 19:17:22 10.10.1.10 GET /Purchasing/Home - 80 - 10.10.1.12 Mozilla/5.0+(Windows;+U;+Windows+NT+6.1;+en-US;+rv:1.9.2.6)+Gecko/20100625+Firefox/3.6.6 401 0 0 4414

  Read the article

• Windows 7 file-based backup service

  - by Ben Voigt

  I'm looking for a good replacement for Lazy Mirror, since it doesn't support Windows 7 well. Pros: One of the things I really loved about Lazy Mirror is that it always maintains a "full" backup, but does so by only copying modified files. As each file was copied, the old version got archived (moved to an out-of-the-way location). So after mirroring ran, there'd be a complete copy of the file system, which could even be booted if necessary. At the same time, extra space on the backup media was used to store as many older versions of files as possible, without wasting space storing multiple copies of the same version. It seems that with Windows 7 backup, there'd be wasted space storing the same data in both the system image and file backup. It was completely file-based, but also aware of the registry (it had a feature to dump the live registry to hive files in the correct format). The backups were normal NTFS filesystems, no special tool was needed to read them. It automatically cleaned out the oldest previous versions when space ran out (unlike Windows 7 backup which apparently simply starts failing the the backup media fills.) It copied all file attributes including security. Cons: It doesn't deal well with junction points, symbolic links, and hard links. It didn't run as a service without lots of help from firesrv or srvany, and then you couldn't interact with the GUI. Running as a service was necessary to be able to mirror protected OS files. It didn't have open file handling, except for registry hives. I guess that the file-by-file archive and replacement could leave mismatched sets of files, if the mirror was interrupted. This would be the advantage of incremental backup techniques that require old full backup + all intermediate incremental backups to restore. But I don't see this as presenting much of a problem, you'd really only have a boot failure if you had a mixture of pre- and post-service pack files, and I can run a full image backup using another tool before applying a service pack. Does anyone know of a tool that does both full-system backup and storage of old versions of files like Lazy Mirror did (without storing the same data multiple times), and also can run as a service in Windows 7? Free is best of course, but a reasonably priced paid program (e.g. It would be absolutely awesome if it also triggered a backup/mirror pass when a particular external drive was plugged in and generated popup warnings if backups hadn't been run recently)

  Read the article

• Choosing my first Domain Registrar?

  - by user36914

  This will be the first domain i've ever registered. So i'm at a loss what to look for. I definitely don't want to go with GoDaddy. Here are my requirements: Must have unlimited email forwards for my domain Easy to transfer away if i choose. Must not be one of those shady registrars that will try to auction your domain at the end. Ability to create sub domains Domain Registration is Private I would like a domain registrar that would let me use my dynamic ip of my ISP (Cable) if i want to. So hopefully they would have some type program that would detect IP changes and update accordingly So i've looked at a variety of registrars so far. The three left were really NameCheap, DreamHost, & DomainMonster. I have heard good things about DreamHost but i think its off the list because they don't give you any information about the features you get when you register your domain with them. They have a "Whats included" button the page but it mainly list the features with hosting not registration. DomainMonster looks pretty cool but i don't see anything about subdomains. Also i would assume they don't have a system for dynamic ip address updating. So you would have to constantly check that your ip of your ISP has changed or not and update it manually. NameCheap also looks nice. There are two things i really like about them. Right on their feature page they list "Free Dynamic DNS With Client" which is pretty cool. They also have a free SSL certificate for the first year. Haven't messed a lot with certificates but this would definitely be something i would use. Only minus i can see is you only get free private whois for the first year. After that its $2.99 which isn't that big of a deal. I'm leaning towards NameCheap now. Is this a good choice. Is there anything else i should be looking at?

  Read the article

• Dual head setup for Ubuntu 10.04.1 and Windows XP Pro with same hardware configuration

  - by mejpark

  I have a Dell OptiPlex 360 workstation at work, with 2 x ATI RV280 [Radeon 9200 PRO] graphics cards installed, which are attached to two identical 19" HII flat panel monitors. I'm using the open source Radeon driver with Ubuntu, and the proprietary drivers with Windows. The good news is that dual head configuration works for both OSes. The bad news is, I have to use a different hardware configuration for each OS to achieve this. Hardware config #1: Dual monitors work for Windows XP Pro like this: First display -> external VGA port Second display -> DVI input on gfx card Hardware config #2: Dual monitors work for Ubuntu 10.04.1 like this: First display -> VGA port on gfx card Second display -> DVI input on gfx card I connected up the displays according to Config #2 and booted up Windows, which resulted in a mirror image on both screens. I was unable to login, as the login box was not visible. I unplugged the VGA lead from gfx card and plugged it into the external VGA port (Config #1) - Windows dual head works again, but the VGA-connected screen is not recognised by Ubuntu and remains in standby mode. Is it possible to configure a dual head setup for Ubuntu using Config #1, or am I missing something? I tried setting up dual monitors using Config #1, this morning which didn't work. By default, there is no xorg.conf file in Ubuntu 10.04.1, so I generated one using: $ sudo X :2 -configure X.Org X Server 1.7.6 Release Date: 2010-03-17 X Protocol Version 11, Revision 0 Build Operating System: Linux 2.6.24-27-server i686 Ubuntu Current Operating System: Linux harrier 2.6.32-24-generic #42-Ubuntu SMP Fri Aug 20 14:24:04 UTC 2010 i686 Kernel command line: BOOT_IMAGE=/boot/vmlinuz-2.6.32-24-generic root=UUID=a34c1931-98d4-4a34-880c-c227a2936c4a ro quiet splash Build Date: 21 July 2010 12:47:34PM xorg-server 2:1.7.6-2ubuntu7.3 (For technical support please see http://www.ubuntu.com/support) Current version of pixman: 0.16.4 Before reporting problems, check http://wiki.x.org to make sure that you have the latest version. Markers: (--) probed, (**) from config file, (==) default setting, (++) from command line, (!!) notice, (II) informational, (WW) warning, (EE) error, (NI) not implemented, (??) unknown. (==) Log file: "/var/log/Xorg.2.log", Time: Mon Sep 13 10:02:02 2010 List of video drivers: apm ark intel mach64 s3virge trident mga tseng ati nouveau neomagic i740 openchrome voodoo s3 i128 radeon siliconmotion nv ztv vmware v4l chips rendition savage sisusb tdfx geode sis r128 cirrus fbdev vesa (++) Using config file: "/home/michael/xorg.conf.new" (==) Using config directory: "/usr/lib/X11/xorg.conf.d" (II) [KMS] No DRICreatePCIBusID symbol, no kernel modesetting. Xorg detected your mouse at device /dev/input/mice. Please check your config if the mouse is still not operational, as by default Xorg tries to autodetect the protocol. Xorg has configured a multihead system, please check your config. Your xorg.conf file is /home/michael/xorg.conf.new To test the server, run 'X -config /home/michael/xorg.conf.new' ddxSigGiveUp: Closing log $ sudo X -config /home/michael/xorg.conf.new Fatal server error: Server is already active for display 0 If this server is no longer running, remove /tmp/.X0-lock and start again. Please consult the The X.Org Foundation support at http://wiki.x.org for help. ddxSigGiveUp: Closing log I then booted Ubuntu in failsafe mode, dropped into root shell, and executed $ X -config /home/michael/xorg.conf.new again. The screen went blank and turned off, so

  Read the article

• Permission denied install Joomla CiviCRM

  - by Tim

  Dear All, I am trying to install CiviCRM on a Joomla 1.5.17 web server running Ubuntu 9.10. Uploading the package to the tmp directory in /var/www/[site name]/tmp and installing creates this error: Warning: fopen(/var/www/trbcp/administrator/components/com_civicrm/civicrm/templates/CRM/common/civicrm.settings.php.tpl) [function.fopen]: failed to open stream: Permission denied in /var/www/trbcp/libraries/joomla/filesystem/file.php on line 240 Warning: fopen(/var/www/trbcp/administrator/components/com_civicrm/civicrm/templates/CRM/common/civicrm.settings.php.tpl) [function.fopen]: failed to open stream: Permission denied in /var/www/trbcp/libraries/joomla/filesystem/file.php on line 240 Warning: include_once(/var/www/trbcp/administrator/components/com_civicrm/civicrm.settings.php) [function.include-once]: failed to open stream: Permission denied in /var/www/trbcp/administrator/components/com_civicrm/configure.php on line 115 Warning: include_once() [function.include]: Failed opening '/var/www/trbcp/administrator/components/com_civicrm/civicrm.settings.php' for inclusion (include_path='.') in /var/www/trbcp/administrator/components/com_civicrm/configure.php on line 115 Warning: require_once(DB.php) [function.require-once]: failed to open stream: No such file or directory in /var/www/trbcp/administrator/components/com_civicrm/configure.php on line 140 Fatal error: require_once() [function.require]: Failed opening required 'DB.php' (include_path='.') in /var/www/trbcp/administrator/components/com_civicrm/configure.php on line 140 Initially I got a permissions denied error and thought that Joomla did not have permissions to all its directories but looking at Help-System information all the necessary directories are writable. I then decided to chmod 777 all the directories and try again but it still fails. Looking at the directories afterwards it seems that the new directories being created are not being created 777. By changing them I can get at least one step further before the error appears again. My question is does anyone know how to get round this? I am thinking that the new directories being created will require sudo privileges to have mv and create actions carried out, hence the permission denied errors. Can this be configured in Joomla? Or is there a way to specify that new directories created in /var/www/[site name] take 777 by default? any help greatly appreciated! EDIT: P.S. if anyone could give me a clue as to how the insert code feature works as well that would be great! Might make this post a bit more readable! EDIT2: Well I have had a bash at changing the permissions and ownership. sudo chown -R www-data:www-data /var/www/trbcp I then tried changing the whole /var directory (insecure I know but this is a test and dev server for me to find my feet on) to 777 and still getting permission errors. It seems to be error opening stream? Not a php guy so not sure what that is but could it be that permissions to run php script need to change? any thoughts greatly appreciated.

  Read the article

• htaccess on remote server issues - password prompt not accepting input

  - by pying saucepan

  EDIT: I will contact the university about my problem after labor day weekend, but I thought if someone knew a quick fix that I haven't tried, or if the problem has an obvious fix then I could hope to try my luck here, thanks! TLDR: Sorry its a long post, I thought I should be... thorough. I am having a common issue (found a dead thread through google with no solution to the same problem) with the prompt to enter in a username and password via htaccess rights, but this prompt will keep popping up asking for a username and password when trying to access my home directory on my university's server which has the .htaccess and .htpasswd files. It does not matter if I enter in correct or incorrect credentials, the prompt will keep asking me for input without displaying my home directory. Ever since I have included these ht files I have never once been able to get past the username/password no matter what I have tried, save for removing them from the directory I am trying to access (my top level directory that I own). This kind of served my original goal of making the top level directory inaccessible to casual users, but if I wanted to use this method on other places, I would want it to work as intended. And I also like it when computers do what I wish they would, so any help is appreciated. Some things I have tried: Changing the file/directory access rights: they told me to try these commands if people can't access my files cd ~/public_html find ./ -type d -exec chmod 755 {} \; find ./ -type f -exec chmod 644 {} \; enter in the single character name/pw at least twenty times in a row, no cheddar. so I changed directory with cd ~ in hopes that this would be my home directory, since my home directory contains the "public_html" directory, so logic tells me that the ~ tilde symbol is the top level directory that I have ownership of. Then I did those two commands to change the rights on the files inside, I am still having no luck. How I got to this point: I have been following the instructions given to me through my university's website for setting up my little directory. A link on how they describe how to password protect the home directory is given below: "Protect Web Directories" instructions I have everything in order except for one small detail that I feel probably does not matter. I am on windows and so I am using winSCP to remote control my allocated server space. The small detail is that as the instructions indicate (on step 3) that I should use the command htpasswd -c .htpasswd {username} where {username} is my folder that holds my allocated server space. But this command requires further input through the terminal, and unfortunately winSCP does not offer this kind of functionality. So I looked up some basic instructions on using htaccess and it is formatted correctly such that the .htaccess file appears as follows: AuthType Basic AuthName "Verify" AuthUserFile /correctpath/.htpasswd require valid-user and this file is in the root directory for my server space as well as the .htpasswd file which has only this data inside: username:password I know for sure that these two files must be formatted correctly, at least according to their tutorial, because before my path was incorrectly formatted via including some curly { braces } without knowing the correct way to do this at first. And the password prompt that shows up when accessing my directory responded by loading an error page indicating to contact OSU admin or something not important. But now that I have everything like it 'should' be. I know this because when I enter in my credentials "username and password" the prompt pops up for my username and password again and again whether or not I enter in correct information. The only exception is that if I click cancel it will direct me to a page saying that I need to enter in a username and password. Note that I am very inexperienced at server-related buisness, two days ago I couldn't have told you what a website actually consists of. So, if you use some technical jargon I may or may not need to look it up and get back to you before I actually understand what you mean, but I am a quick learner and it probably wont matter.

  Read the article

• How to configure Transparent IP Address Sharing (TAS) on a Mediatrix 4102 with DGW 2.0 firmware?

  - by Pascal Bourque

  I am making the switch to VoIP. I chose voip.ms as my service provider and Mediatrix 4102 as my ATA. One reason why I chose the Mediatrix over other popular consumer ATAs is that it's supposed to be easy to place it in front of the router, so it can give priority to its own upstream traffic over the home network's upstream traffic. This is supposed to work transparently, with the ATA and router sharing the same public IP address (the one obtained from the modem). They call this feaure Transparent IP Address Sharing, or TAS. Their promotional brochure describes it like this: The Mediatrix 4102 also uses its innovative TAS (Transparent IP Address Sharing) technology and an embedded PPPoE client to allow the PC (or router) connected to the second Ethernet port to have the same public IP address, eliminating the need for private IP addresses or address translations. I am interested by this feature because my router, an Apple Time Capsule, doesn't support QoS and cannot give priority to the voice packets if the ATA is behind the router. However, after hours of searching the web, reading the documentation, and good ol' trial and error, I haven't been able to configure the Mediatrix to run in this mode. Then I found a version of the manual that looks like it was for a previous version of the firmware (SIP), where there is an entire section dedicated to configuring TAS (starting at page 209). But my Mediatrix comes with the DGW 2.0 firmware, whose documentation does not mention TAS at all. So I tried to follow the TAS setup instructions from the SIP documentation and apply them to my DGW firmware, using the Variable Mapping Between SIP v5.0 and DGW v2.0 document as a reference, but no success. Some required SIP variables don't have an equivalent in DGW. So it looks like the DGW firmware does not support TAS at all, or if it does they are not doing anything to help us set it up. So right now, the Mediatrix is behind the router and VoIP works perfectly except when my upstream bandwidth is saturated. My questions are: Is downgrading to SIP firmware the only way to have my Mediatrix 4102 run in TAS mode? If not, anybody knows how to setup TAS on the DGW firmware? Is TAS mode the only way to give priority to the voice packets if I want to keep my current router (Apple Time Capsule)? Thanks!

  Read the article

• How do I correct a directory incorrectly copied into itself?

  - by Peter Boughton

  Given the following situation... <path>/mydir1/mydir2 ...where mydir2 should have overwritten mydir1, but was instead placed inside, and both directories actually have the same filename. How is that fixed? Attempting to do mv <path>/mydir/mydir/* <path>/mydir/ or mv <path>/mydir <path>/ results in: mv: cannot move `<path>/mydir/mydir` to a subdirectory of itself, `<path>/mydir` This seems stupidly simple, but it's late here and I can't figure it out. There are seventeen such directories to fix (path differs for each, but same mydir name). To confirm, the error message can be caused with this: # cd /path/to/directory # mv mydir/mydir ./ mv: cannot move `mydir/mydir' to a subdirectory of itself, `./mydir' Also tried: # mv mydir/mydir/* mydir/ mv: cannot move `mydir/mydir/otherdir1' to a subdirectory of itself, `mydir/otherdir1' mv: cannot move `mydir/mydir/otherdir2' to a subdirectory of itself, `mydir/otherdir2' and... # mv /path/to/directory/mydir/mydir/otherdir1 /path/to/directory/mydir/ mv: cannot move `/path/to/directory/mydir/mydir/otherdir1' to a subdirectory of itself, `/path/to/directory/mydir/otherdir1' and using a temporary directory: # mv mydir/mydir ./mydir-temp # mv mydir-temp/* mydir/ mv: cannot move `mydir-temp/otherdir1' to a subdirectory of itself, `mydir/otherdir1' mv: cannot move `mydir-temp/otherdir2' to a subdirectory of itself, `mydir/otherdir2' I found a similar question "How to recursively move all files (including hidden) in a subfolder into a parent folder in *nix?" which suggested that mv bar/{,.}* . would do this. But this also gives the same errors, as well as confusingly picking up . and .. from somewhere. # cd mydir # mv mydir/{,.}* . mv: cannot move `mydir/otherdir1' to a subdirectory of itself, `./otherdir1' mv: cannot move `mydir/otherdir2' to a subdirectory of itself, `./otherdir2' mv: cannot move `mydir/.' to `./.': Device or resource busy mv: cannot move `mydir/..' to `./..': Device or resource busy mv: overwrite `./.file'? y Another similar question "linux mv command weirdness" suggests that mv doesn't overwrite and a copy is required. # cd mydir # cp -rf ./mydir/* ./ cp: overwrite `./otherdir1/file1'? y cp: overwrite `./otherdir1/file2'? y cp: overwrite `./otherdir1/file3'? This appears to be working... except there's a lot of files (and dirs) - I don't want to confirm every one! Isn't the f there supposed to prevent this? Ok, so cp was aliased to cp -i (which I found out with type cp), and bypassed by using \cp -rf ./mydir/* ./ which seems to have worked. Although I've solved the problem of getting dirs/files from one place to another, I'm still curious as to what's going on with the mv stuff - is this really a deliberate feature as suggested by Warner?

  Read the article

• Fix/Bypass "Cannot connect to the real website-blocked" error in Google Chrome with OpenDNS blocking

  - by George H

  I have a large problem with Chrome in my organisation. I use DNS to manage web site blocking, for sites which are not appropriate and are potentially a risk to the organisation where I do this. I only want to use Chrome over the network, as Internet Explorer has compatibility problems with some sites that we use (We cannot change this either or use different sites). Therefore using internet explorer is not a solution. I do not want to install a different browser, for multiple reasons. Mainly because of the difficulty of rewriting the customised add-ons that we use. However, recently, I have had lots of problems with Chrome SSL Errors. I cannot use my custom OpenDNS block pages, which uses the contact form to request an unblocking. Chrome often blocks OpenDNS for sites (a good example is Facebook) that request HTTPS. Some sites like https://internetbadguys.com (OpenDNS example) This means that chrome refuses to load the blocking page, explaining that the site is blocked. Instead they often call IT support, but they want a solution, as they are sick of getting lots of SSL errors. I have tried looking into ways to turning this off. I have tried: Typing "proceed". That didn't work. Typing "proceed", pressing enter. Didn't work I cannot find phishing and anti-malware any more in Chrome, from the internet guides. Not using HTTPS. However there is an automatic redirect to HTTPS on most sites. Therefore the error keeps coming up. Checking my clocks. They were correct. Does anyone have an idea on how to disabling, bypassing or working around this "feature"? EDIT: This is an example what I am talking about - I found that on google images. I do not block google. EDIT 2: My clocks are correct. I cannot stop using OpenDNS either. EDIT 3: My question is: How do I stop chrome from refusing to load pages that are blocked by OpenDNS, where the server has explicitly requested HTTPS.

  Read the article

• what is the best mid/high-end class audio/music creation audio sound card?

  - by Chris

  Hello, I have a computershop myself, and I repair computers. But one of the things I really don't know (yet) is the performace od audio cards for music creation with midi. I have searched and searched and came up with some good reviews, but after browsing for a couple of hours I could't see the trees trough the forrest :-D (it's a dutch expression) At one moment I thought the M-Audio - Delta 1010LT would be a good PCIe card, later on I read that this card was released years ago. (but that could be false information) Also any personal expierence would be great, but not necessairy. I have searched a few cards, and I hope someone can help me make a choice for a friend of mine. He's buget is between $100 and $350 I know there are audio cards from $ 500 - $1850,- this is just too expensive. The following specs are crucial: ASIO Midi Mic in minimal 5.1, 7.1 recommended it's not for airplay, but just to compose music at home. using Ableton and midi keyboard. 1. M-Audio - Delta 1010LT: 8 x 8 analog I/O 2 mic preamps or line inputs S/PDIF digital I/O (coaxial) with 2-channel PCM SCMS copy protection control digital I/O supports surround-encoded AC-3 and DTS pass-through 1 x 1 MIDI I/O directly drive up to 7.1 surround (bass management software included) software controlled 36-bit internal DSP digital mixing/routing +4dbu/-10dBV operation individually switched in software word clock I/O for sample accurate device synchronization 2. RME HDSP 9632: * Stereo Analog Ein- und Ausgang, symmetrisch*, 24-Bit/192kHz, > 110 dB SNR * Optionale Erweiterungsboards mit je 4 symmetrischen Ein- und Ausgängen * Alle analogen I/Os voll 192 kHz-fähig, also keine Reduzierung der Kanalzahl * 1 x ADAT Digital In/Out, 96 kHz-fähig (S/MUX) * 1 x SPDIF Digital In/Out, 192 kHz-fähig * 1 x Breakout Kabel für koaxialen SPDIF-Betrieb* * Also bis zu 16 Ein-und Ausgänge gleichzeitig nutzbar! * 1 x Stereo Kopfhörerausgang, parallel zum analogen Ausgang, aber eigene Pegelanpassung * 1 x MIDI I/O für 16 Kanäle Hi-Speed MIDI über Breakout Kabel * DIGICheck, RMEs einzigartiges Meter- und Analysetool mit Spectral Analyser, Professionelle Level Meter 2/8/16-Kanalig, Vector Audio Scope und diversen weiteren Analysefunktionen * HDSP Meter Bridge: Frei skalierbare Levelmeter mit Peak- und RMS Berechnung in Hardware * TotalMix: 512-Kanal Mischer mit 40 Bit interner Auflösung 3. EMU 1212M (1212 M) PCIe: * Top kwaliteit convertors 24-bit/192kHz convertors. * Hardware gestuurde effecten. * DSP zero-latency hardware mixen en monitoring. * Analoge en digitale I/O plus MIDI. * EMU Production Tools Software Bundle - Cakewalk SONAR , Steinberg Cubase LE, Ableton Live E-MU Edition **EMU 1212M PCI-e inputs/outputs:** * 2 balanced jack inputs. * 2 balanced jack outputs. * 24-bit/192kHz ADAT I/O. * 24-bit/192kHz Coaxiale S/PDif I/O switchable to AES/EBU. * MIDI I/O. 4. M-Audio Audiophile 192: - Up to 24-bit/192kHz audio - 2 balanced analog inputs (1/4” TRS) - 2 balanced analog outputs (1/4” TRS) - S/PDIF digital I/O (coaxial RCA connectors) with 2-channel PCM - SCMS copy protection control - Digital I/O supports surround-encoded AC-3 and DTS pass-through - Direct hardware input monitoring via separate balanced 1/4” TRS monitor outputs - Software routing of inputs and outputs - Digital I/O can be routed to/from external effects - 16-channel MIDI I/O - ASIO, WDM, GSIF 2 and Core Audio driver support for compatibility with most applications - 64-bit driver support for Windows - PCI 2.2 compatibility - Apple G5 compatible - Incompatible exceptions - Includes Ableton Live Lite music production software, so you can make music right away - Works with other Delta cards Technical Specifcations: - Compatibility - ASIO - WDM - GSIF 2 - Core Audio

  Read the article

• Allow email from a particular sender through spam filter

  - by Greg

  We are running exchange 2010 and are using the built in anti-spam feature. We have set up Content Filtering, IP Block List Providers, Sender ID, Sender Reputation and it filters out most of the junk but it also quarantines all emails from one of our customers. It is being quarantined because of the Content Filter agent (Report Below). How can I add an exception for this email address to the Content Filter. I can see how to setup an exception for a delivery address ("Don't filter messages sent TO the following recipients") but I want to add [email protected] to our safe list. I don't want to add the whole domain as it is a very popular ISP in Australia and we often get junk from them. Filter Report: > Diagnostic information for administrators: > > Generating server: something.com > > [email protected] > #550 5.2.1 Content Filter agent quarantined this message ## > > Original message headers: > > Received: from icp-osb-irony-out4.external.iinet.net.au (203.59.1.220) > by server.local.something.com.au (192.5.0.105) with Microsoft SMTP > Server id > 14.1.218.12; Mon, 5 Nov 2012 02:40:40 +1100 X-IronPort-Anti-Spam-Filtered: true X-IronPort-Anti-Spam-Result: > AscOALeLllB8qwLw/2dsb2JhbABEKYUFhiigRQOWCwQEgQiBCIIZFAEBTiwCCAIBBwEIFDkBBBoqARoCAQIDAYd4uEuRXGEDiCWFT44UijeDAw > X-IronPort-AV: E=Sophos;i="4.80,710,1344182400"; > d="scan'208,217";a="55137861" Received: from unknown (HELO > asdf83c05c53a3) ([124.171.2.240]) by icp-osb-irony-out4.iinet.net.au > with ESMTP; 04 Nov 2012 23:40:26 +0800 Message-ID: > <E8C866D0299E4BCB8B156723893EB735@asdf83c05c53a3> From: Customer > <[email protected]> To: 'Person' <[email protected]> > Subject: A long sentance Date: Mon, 5 Nov 2011 06:07:57 +1100 > MIME-Version: 1.0 Content-Type: multipart/alternative; > boundary="----=_NextPart_000_0005_01C5F962.3CD09120" X-Priority: 3 > X-MSMail-Priority: Normal X-Mailer: Microsoft Outlook Express > 6.00.2900.5931 X-MimeOLE: Produced By Microsoft MimeOLE V6.00.2900.6157 Return-Path: [email protected] Received-SPF: None > (server.local.something.com.au: [email protected] does not > designate permitted sender hosts)

  Read the article

• How to configure Transparent IP Address Sharing (TAS) on a Mediatrix 4102 with DGW 2.0 firmware?

  - by Pascal Bourque

  I am making the switch to VoIP. I chose voip.ms as my service provider and Mediatrix 4102 as my ATA. One reason why I chose the Mediatrix over other popular consumer ATAs is that it's supposed to be easy to place it in front of the router, so it can give priority to its own upstream traffic over the home network's upstream traffic. This is supposed to work transparently, with the ATA and router sharing the same public IP address (the one obtained from the modem). They call this feaure Transparent IP Address Sharing, or TAS. Their promotional brochure describes it like this: The Mediatrix 4102 also uses its innovative TAS (Transparent IP Address Sharing) technology and an embedded PPPoE client to allow the PC (or router) connected to the second Ethernet port to have the same public IP address, eliminating the need for private IP addresses or address translations. I am interested by this feature because my router, an Apple Time Capsule, doesn't support QoS and cannot give priority to the voice packets if the ATA is behind the router. However, after hours of searching the web, reading the documentation, and good ol' trial and error, I haven't been able to configure the Mediatrix to run in this mode. Then I found a version of the manual that looks like it was for a previous version of the firmware (SIP), where there is an entire section dedicated to configuring TAS (starting at page 209). But my Mediatrix comes with the DGW 2.0 firmware, whose documentation does not mention TAS at all. So I tried to follow the TAS setup instructions from the SIP documentation and apply them to my DGW firmware, using the Variable Mapping Between SIP v5.0 and DGW v2.0 document as a reference, but no success. Some required SIP variables don't have an equivalent in DGW. So it looks like the DGW firmware does not support TAS at all, or if it does they are not doing anything to help us set it up. So right now, the Mediatrix is behind the router and VoIP works perfectly except when my upstream bandwidth is saturated. My questions are: Is downgrading to SIP firmware the only way to have my Mediatrix 4102 run in TAS mode? If not, anybody knows how to setup TAS on the DGW firmware? Is TAS mode the only way to give priority to the voice packets if I want to keep my current router (Apple Time Capsule)? Thanks!

  Read the article

• iptables management tools for large scale environment

  - by womble

  The environment I'm operating in is a large-scale web hosting operation (several hundred servers under management, almost-all-public addressing, etc -- so anything that talks about managing ADSL links is unlikely to work well), and we're looking for something that will be comfortable managing both the core ruleset (around 12,000 entries in iptables at current count) plus the host-based rulesets we manage for customers. Our core router ruleset changes a few times a day, and the host-based rulesets would change maybe 50 times a month (across all the servers, so maybe one change per five servers per month). We're currently using filtergen (which is balls in general, and super-balls at our scale of operation), and I've used shorewall in the past at other jobs (which would be preferable to filtergen, but I figure there's got to be something out there that's better than that). The "musts" we've come up with for any replacement system are: Must generate a ruleset fairly quickly (a filtergen run on our ruleset takes 15-20 minutes; this is just insane) -- this is related to the next point: Must generate an iptables-restore style file and load that in one hit, not call iptables for every rule insert Must not take down the firewall for an extended period while the ruleset reloads (again, this is a consequence of the above point) Must support IPv6 (we aren't deploying anything new that isn't IPv6 compatible) Must be DFSG-free Must use plain-text configuration files (as we run everything through revision control, and using standard Unix text-manipulation tools are our SOP) Must support both RedHat and Debian (packaged preferred, but at the very least mustn't be overtly hostile to either distro's standards) Must support the ability to run arbitrary iptables commands to support features that aren't part of the system's "native language" Anything that doesn't meet all these criteria will not be considered. The following are our "nice to haves": Should support config file "fragments" (that is, you can drop a pile of files in a directory and say to the firewall "include everything in this directory in the ruleset"; we use configuration management extensively and would like to use this feature to provide service-specific rules automatically) Should support raw tables Should allow you to specify particular ICMP in both incoming packets and REJECT rules Should gracefully support hostnames that resolve to more than one IP address (we've been caught by this one a few times with filtergen; it's a rather royal pain in the butt) The more optional/weird iptables features that the tool supports (either natively or via existing or easily-writable plugins) the better. We use strange features of iptables now and then, and the more of those that "just work", the better for everyone.

  Read the article

• Why isn't this rewrite rule (nginx) applied? (trying to setup Wordpress multisite)

  - by Brian Park

  Hi, I'm trying to setup Wordpress multisite (subfolder structure) with nginx, but having a problem with this rewrite rule. Below is the Apache's .htaccess, which I have to translate into nginx configuration. RewriteEngine On RewriteBase /blogs/ RewriteRule ^index\.php$ - [L] # uploaded files RewriteRule ^([_0-9a-zA-Z-]+/)?files/(.+) wp-includes/ms-files.php?file=$2 [L] # add a trailing slash to /wp-admin RewriteRule ^([_0-9a-zA-Z-]+/)?wp-admin$ $1wp-admin/ [R=301,L] RewriteCond %{REQUEST_FILENAME} -f [OR] RewriteCond %{REQUEST_FILENAME} -d RewriteRule ^ - [L] RewriteRule ^([_0-9a-zA-Z-]+/)?(wp-(content|admin|includes).*) $2 [L] RewriteRule ^([_0-9a-zA-Z-]+/)?(.*\.php)$ $2 [L] RewriteRule . index.php [L] Below is what I came up with: server { listen 80; server_name example.com; server_name_in_redirect off; expires 1d; access_log /srv/www/example.com/logs/access.log; error_log /srv/www/example.com/logs/error.log; root /srv/www/example.com/public; index index.html; try_files $uri $uri/ /index.html; # rewriting uploaded files rewrite ^/blogs/(.+/)?files/(.+) /blogs/wp-includes/ms-files.php?file=$2 last; # add a trailing slash to /wp-admin rewrite ^/blogs/(.+/)?wp-admin$ /blogs/$1wp-admin/ permanent; if (!-e $request_filename) { rewrite ^/blogs/(.+/)?(wp-(content|admin|includes).*) /blogs/$2 last; rewrite ^/blogs/(.+/)?(.*\.php)$ /blogs/$2 last; } location /blogs/ { index index.php; #try_files $uri $uri/ /blogs/index.php?q=$uri&$args; } location ~ \.php$ { include /etc/nginx/fastcgi_params; fastcgi_pass 127.0.0.1:9000; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME /srv/www/example.com/public$fastcgi_script_name; } # static assets location ~* ^.+\.(manifest)$ { access_log /srv/www/example.com/logs/static.log; } location ~* ^.+\.(ico|ogg|ogv|svg|svgz|eot|otf|woff|mp4|ttf|css|rss|atom|js|jpg|jpeg|gif|png|ico|zip|tgz|gz|rar|bz2|doc|xls|exe|ppt|tar|mid|midi|wav|bmp|rtf)$ { # only set expires max IFF the file is a static file and exists if (-f $request_filename) { expires max; access_log /srv/www/example.com/logs/static.log; } } } In the above code, I believe rewrite ^/blogs/(.+/)?(.*\.php)$ /blogs/$2 last; has no effect because when I look at the access_log file, I see the following line: 2010/09/15 01:14:55 [error] 10166#0: *8 "/srv/www/example.com/public/blogs/test/index.php" is not found (2: No such file or directory), request: "GET /blogs/test/ HTTP/1.1" (Here, 'test' is the second blog created using multisite feature) What I'm expecting is that /blogs/test/index.php gets rewritten to /blogs/index.php, but it doesn't seem to do that... Am I overlooking something obvious? Thanks!

  Read the article

• Using IIS7 why are my PNGs being cached by the browser, but my JS and CSS files not?

  - by Craig Shearer

  I am trying to sort out caching in IIS for my site. Basically, I want nothing cached, except for .png, .js, and .css files. At my site level, I opened the HTTP Reponse Headers and used the "Set Common Hedaers..." to set content to expire immediately. I have no Output Caching profiles set at any level in IIS. I clear my browser cache then try accessing my site. When my site requests a PNG file, I see responses like: Accept-Ranges bytes Age 0 Connection Keep-Alive Content-Type image/png Date Thu, 12 Apr 2012 21:55:15 GMT Etag "83b7322de318cd1:0" Last-Modified Thu, 12 Apr 2012 19:33:45 GMT Server Microsoft-IIS/7.5 X-Powered-By ASP.NET For JS and CSS files, I see responses like: Accept-Ranges bytes Cache-Control no-cache Connection Keep-Alive Content-Encoding gzip Content-Length 597 Content-Type text/css Date Thu, 12 Apr 2012 21:55:15 GMT Etag "06e45ede15bca1:0" Last-Modified Mon, 02 Nov 2009 17:28:44 GMT Server Microsoft-IIS/7.5 Vary Accept-Encoding X-Powered-By ASP.NET Accept-Ranges bytes Cache-Control no-cache Connection Keep-Alive Content-Encoding gzip Content-Length 42060 Content-Type application/x-javascript Date Thu, 12 Apr 2012 21:55:14 GMT Etag "2356302de318cd1:0" Last-Modified Thu, 12 Apr 2012 19:33:45 GMT Server Microsoft-IIS/7.5 Vary Accept-Encoding X-Powered-By ASP.NET So, why are my PNGs able to be cached, but JS and CSS files not? Then, I go into the Output Caching feature in IIS and set up profiles for .png, .css, and .js files. This updates the web.config file as follows: <caching> <profiles> <add extension=".png" policy="CacheUntilChange" kernelCachePolicy="DontCache" /> <add extension=".css" policy="CacheUntilChange" kernelCachePolicy="DontCache" /> <add extension=".js" policy="CacheUntilChange" kernelCachePolicy="DontCache" /> </profiles> </caching> I do a "precautionary" IISReset then try accessing my site again. For PNG files, I see the following response: Accept-Ranges bytes Age 0 Connection Keep-Alive Content-Length 3833 Content-Type image/png Date Thu, 12 Apr 2012 22:02:30 GMT Etag "0548c9e2c5dc81:0" Last-Modified Tue, 22 Jan 2008 19:26:00 GMT Server Microsoft-IIS/7.5 X-Powered-By ASP.NET For CSS and JS files, I see the following responses: Accept-Ranges bytes Cache-Control no-cache,no-cache Connection Keep-Alive Content-Encoding gzip Content-Length 2680 Content-Type application/x-javascript Date Thu, 12 Apr 2012 22:02:29 GMT Etag "0f743af9015c81:0" Last-Modified Tue, 23 Oct 2007 16:20:54 GMT Server Microsoft-IIS/7.5 Vary Accept-Encoding X-Powered-By ASP.NET Accept-Ranges bytes Cache-Control no-cache,no-cache Connection Keep-Alive Content-Encoding gzip Content-Length 3831 Content-Type text/css Date Thu, 12 Apr 2012 22:02:29 GMT Etag "c3f42d2de318cd1:0" Last-Modified Thu, 12 Apr 2012 19:33:45 GMT Server Microsoft-IIS/7.5 Vary Accept-Encoding X-Powered-By ASP.NET What am I doing wrong? Have I completely misunderstood the features of IIS, or is there a bug. Most importantly, how do I achieve what I want - that is get the browser to cache only PNG, JS and CSS files?

  Read the article

• Backing up data stored on Amazon S3

  - by Fiver

  I have an EC2 instance running a web server that stores users' uploaded files to S3. The files are written once and never change, but are retrieved occasionally by the users. We will likely accumulate somewhere around 200-500GB of data per year. We would like to ensure this data is safe, particularly from accidental deletions and would like to be able to restore files that were deleted regardless of the reason. I have read about the versioning feature for S3 buckets, but I cannot seem to find if recovery is possible for files with no modification history. See the AWS docs here on versioning: http://docs.aws.amazon.com/AmazonS3/latest/dev/ObjectVersioning.html In those examples, they don't show the scenario where data is uploaded, but never modified, and then deleted. Are files deleted in this scenario recoverable? Then, we thought we may just backup the S3 files to Glacier using object lifecycle management: http://docs.aws.amazon.com/AmazonS3/latest/dev/object-lifecycle-mgmt.html But, it seems this will not work for us, as the file object is not copied to Glacier but moved to Glacier (more accurately it seems it is an object attribute that is changed, but anyway...). So it seems there is no direct way to backup S3 data, and transferring the data from S3 to local servers may be time-consuming and may incur significant transfer costs over time. Finally, we thought we would create a new bucket every month to serve as a monthly full backup, and copy the original bucket's data to the new one on Day 1. Then using something like duplicity (http://duplicity.nongnu.org/) we would synchronize the backup bucket every night. At the end of the month we would put the backup bucket's contents in Glacier storage, and create a new backup bucket using a new, current copy of the original bucket...and repeat this process. This seems like it would work and minimize the storage / transfer costs, but I'm not sure if duplicity allows bucket-to-bucket transfers directly without bringing data down to the controlling client first. So, I guess there are a couple questions here. First, does S3 versioning allow recovery of files that were never modified? Is there some way to "copy" files from S3 to Glacier that I have missed? Can duplicity or any other tool transfer files between S3 buckets directly to avoid transfer costs? Finally, am I way off the mark in my approach to backing up S3 data? Thanks in advance for any insight you could provide!

  Read the article

• Why many applications close after opening a document or doing a specific actions?

  - by Mohsen Farjami

  I have some encrypted pdf files that have no problem and in my last windows, I could open them easily with Adobe Reader 9.2 and other pdf readers. But now, I can only open non-encrypted pdf files and one encrypted file with Adobe Reader. every time I open almost any encrypted pdf, it closes itself. Also, when I try to search a folder for a keyword with Foxit Reader, once it closed. This is not related to Adobe Reader, because I have the same problem with Word 2007. When I open a document, sometimes it closes instantly and sometimes it closes after a few seconds and sometimes it is stable. My windows is Fresh. I have installed it a few days ago. I have ESET Smart Security 5.2 and I have updated it today. OS: XP Pro SP3, RAM: 3 GB, CPU: 2 GHZ, HDD: 320 GB My installed applications: Adobe AIR Adobe Flash Player 11 ActiveX Adobe Flash Player 11 Plugin Adobe Photoshop CS4 Adobe Reader 9.2 Atheros Wireless LAN Client Adapter Babylon Bluetooth Stack for Windows by Toshiba CCleaner Conexant HD Audio Dell Touchpad ESET Smart Security Farsi (101) Custom Foxit Reader Framing Studio 3.27 Google Chrome Hard Disk Sentinel PRO HDAUDIO Soft Data Fax Modem with SmartCP Intel(R) Graphics Media Accelerator Driver IrfanView (remove only) Java(TM) 6 Update 18 K-Lite Mega Codec Pack 8.8.0 Microsoft .NET Framework 2.0 Service Pack 1 Microsoft .NET Framework 3.0 Service Pack 1 Microsoft .NET Framework 3.5 Microsoft Data Access Components KB870669 Microsoft Office 2007 Primary Interop Assemblies Microsoft Office Enterprise 2007 Microsoft User-Mode Driver Framework Feature Pack 1.0.0 (Pre-Release 5348) Mozilla Firefox 7.0.1 (x86 en-US) Notepad++ Office Tab FreeEdition 8.50 ParsQuran PerfectDisk 12 Professional Registry First Aid RICOH R5C83x/84x Flash Media Controller Driver Ver.3.54.06 Sahar Money Manager 2.5 Stickies 7.1d The KMPlayer (remove only) TurboLaunch 5.1.2 Unlocker 1.9.1 USB Safely Remove 4.2 Virastyar Visual Studio 2005 Tools for Office Second Edition Runtime Winamp Windows Internet Explorer 8 Windows Media Player 11.0.5358.4826 Windows XP Service Pack 3 WinRAR 4.11 (32-bit) WorkPause 1.2 Z Dictionary My startup applications: WorkPause USB Safely Remove TurboLaunch SunJavaUpdateSched Stickies rfagent Persistence ParsQuran Daily Verse ITSecMng IgfxTray HotKeysCmds Hard Disk Sentinel egui disable shift+delete CTFMON.EXE Bluetooth Manager Babylon Client Apoint AdobeCS4ServiceManager Adobe Reader Speed Launcher Adobe ARM What should I do to solve it? If you recommend installing Windows again, what guarantees that it won't happen again?

  Read the article

• Is it possible to "stealth" dual boot a machine?

  - by BrianH

  I have a loaner laptop that has MS Windows with locked down permissions. It works okay for what I need to do, but I started wondering if there was a way to install a separate Windows OS on a separate hard drive to do what I want to do on it. Virtual I wish I could use VirtualBox or VMWare, but that is not an option (I even tried VBox portable). External Drive My next trial was see if it was possible to install Windows on an external drive, and then plug that drive in and boot from it whenever I wanted my own OS. After a few Google searches, I see that is not really a possibility. Swap Primary Drive Another option, would be to get a second internal hard drive, take the existing HD out, and install a new Windows OS on the secondary HD. This would mean swapping the internal hard drive each time I want to switch OSs - doable, but not very convenient. Dual Boot The laptop has an expansion slot where a second hard drive can be plugged in quickly. I thought about Dual booting, but I don't want to mess with the MBR on the primary hard drive. When I have to give the laptop back, I don't want a dual-boot screen to popup. Summary Is there a way to have 2 hard-drives on a machine, each with it's own OS, and maybe use BIOS settings to have only 1 hard drive active at a time? That way both hard drives could be physically connected, but only one would actually be active at a time. I basically want a second OS that does not (can not) affect the existing OS in any way, and can be removed at any time without affecting the existing OS. The secondary OS does not need any of the files on the main hard drive - it's basically like having 2 separate computers using the same hard ware... Is this possible, or would it be easier just to go out and buy a different laptop? Thanks in advance! EDIT I just discovered that my BIOS allows me to pick (at startup) which hard drive I want to boot from. I poked around in the BIOS and there is not a place to disable certain devices, like the primary hard drive. My only concern about plugging in a second hard drive and installing Windows to the second hard drive is that it will mess with the primary hard drive, or add a bootloader screen to pick which windows install to use. My thought would be to physically unplug the primary, plug in the secondary and install windows to the secondary. After the install is working properly, I can plug the primary back in and use the BIOS feature to determine which drive to boot to. Is there any way after I have 2 separate installs on 2 separate hard drives that one of the installs could mess with the MBR on the other drive?

  Read the article

• Symantec Protection Suite and System Recovery 2011 Desktop Edition

  - by rihatum

  I am re-posting this as my previous question was being treated as if I am "Shopping or seeking Product Recommendations" even though I was NOT - BTW they have deleted my comments too which were not offensive in nature. anyway - I have re-phrased some parts of my question and I hope SF Admins "Do Not Modify / Edit" this one - will be most grateful for that. I have a lot of respect for the People who visit this SITE and help others ! Just To clarify : Just to go by SF rules - I am not seeking someone to Design this solution, I am simply seeking real world examples, experiences, technical expert opinions / suggestions, any tips or tricks they may have or any problems they may have faced while doing something similar above with these products. I am also not asking for Capacity Planning for Storage, We have done some research and I am seeking Expert Assurance / Suggestions. We (our company) are planning to deploy Symantec Endpoint Protection and Symantec Desktop Recovery 2011 Desktop Edition to our 3000 - 4000 workstations (Windows7 32 and 64) with a few 100s with Windows XP 32/64 Bit. I have read the implementation guide for SEP and have read tech-notes for Desktop Recovery 2011. Our team have planned to deploy this as follows : 1 x dedicated SQL 2008R2 for Symantec Endpoint Protection (Instead of using the Embedded Database) 1 x Dedicated SQL 2008R2 for Symantec Desktop Recovery 2011 (Instead of using the Embedded Database) 1 x Dedicated W2K8 R2 Box for the SEPM (Symantec Endpoint Protection Manager - Mgmt. APP) 1 x Dedicated W2K8 R2 Box for the Symantec Desktop Recovery 2011 Management Application Agent Deployment : As per Symantec Documentation for both of the above, an agent can be pushed via the Mgmt. Application (provided no firewalls are blocking ports required etc. - we have Windows firewall disabled already). Server Hardware : Per SQL Server : 16GB RAM + SAS DISKS + Dual XEON, RAID-10 for the SQL DB or I can always mount a LUN from our existing Hitachi or EMC SAN. SEPM Server : 16GB RAM + SAS DISKS + DUAL XEON System Recovery MGMT SERVER : 16GB RAM + SAS DISKS + DUAL XEON Above is the initial plan we have for 3000 - 4000 client workstation (Windows) Now my Questions :-) a) If we had these users distributed amongst two sites with AD DC / GC in each site, How would I restrict SEPM and Desktop Mgmt. solution to only check for users in their respective site ? b) At present all users are under one building but we are going to move some dept. to a new location (with dedicated connectivity), How would we control which SEPM / MGMT Server is responsible for which site ? c) We have netbackup in our environment backing up other servers, I am planning to protect these 4 (2 x SQL, 1 x SEPM, 1 x System Recovery Mgmt. Server) via netbackup or I can use System recovery 2011 server edition on all 4 of these boxes as well. (License is not an issue as we have the complete symantec portfolio included in our license). d) Now - Saving Desktop backups - What strategies have you implemented ? Any best practice recommendation for a large user base ? I was thinking to either mount a LUN from our Hitachi SAN on the Symantec Recovery Server itself or backup to the users hard drive locally and then copy it over to a network location ? Suggestions welcome :-) If you have anything to add / correct - that will be really helpful before diving into the actual implementation phase. Will be most grateful with your suggestions, recommendations and corrections with above - Many Thanks !

  Read the article

• Unextending Sharepoint 2007 Web Application from a zone

  - by dunxd

  When our Sharepoint was migrated from Sharepoint 2003 to Sharepoint 2007 (both fully paid versions), the consultants who carried it out extended each web app into two IIS sites/zones (e.g. the original Web App was http://intranet, then http://newintranet and http://intranet would be created for Sharepoint 2007 - each with its own IIS site). The idea was that during the migration period we would set up DNS to point the old url to SP2003 servers and the new one to SP2007, then once the migration was complete, do a DNS change so the SP2007 would recieve the requests to the http://intranet type URLs. Unfortunately the contractors did not tidy up the application extensions and IIS sites after the migration, and for some time both URLs were in use, resulting in many document links pointing to the http://newintranet type URLs. This means I need to maintain these URLs. Due to a rejig of organisation structure we now need to relocate some Sharepoint sites, and I'd like to use the RDA Collaboration Sharepoint URL Redirector feature. However a limitation of this is that it doesn't work for Web Applications which have been extended into multiple zones. So I have a need to tidy up the situation that our consultants left behind. I think the right thing to do is use the "Remove Sharepoint from IIS Web Site" page in Central Admin to remove the zone for the newintranet type sites, and select the option to also delete the IIS site. That should result in having no IIS sites listening for http://newintranet type URLs. Is this the right procedure? Once I have done that I need to set up Sharepoint to receive requests sent to the http://newintranet type URLs so they will continue to work. I am not sure if I should do this: using Alternative Access Mappings or, by adding a host header to the IIS site or, creating a non Sharepoint IIS site for each http://newintranet type URL, and use IIS redirection to forward the requests to the new URL using variables to pass the path to the Sharepoint site. Does anyone have any thoughts on these options, or any other way of achieving this? Sharepoint 2007 is running on Windows 2003 with IIS6. We don't currently have plans/budget to upgrade to Sharepoint 2010.

  Read the article

• Suggestions for splitting server roles amongst Hyper-V virtual servers / RAID6 or RAID10? / AppAssure

  - by Anon

  We have 2 Hyper-V hosts at present running 1 virtual server that was converted from a physical box running all roles. My plan is to split the roles over various virtual machines, upgrading to the latest software versions as I go, and use the backup server as a standby in case the main server fails. AppAssure backup software has a feature called Virtual Standby, so the VHD's can be ready to be fired up on the backup server if necessary. Off-site backups will be done via external USB drive for now. I'm just seeking some input/suggestions into how I'm planning to split the roles out amongst various virtual servers. Also, I'm curious how to setup the storage on the servers. We do not have any NAS's, SAN'S or any budget for this. What would the best RAID level be to use? I'm thinking either RAID6 (which is currently used) however I'm concerned about the write speeds, or RAID10 but again I'm worried that I can only lose 1 drive (from the same mirror) as opposed to any 2 with RAID6. I realise I have a hot swap for this, but what if a further drive fails during a rebuild? Is the write penalty of RAID6 worth the extra reliability over RAID10? Or will it be too slow with all the roles I am planning, therefore RAID10 is my only real option? The reason for the needed redundancy is I am the only technician and I'm not always on-site. Options I've considered: 1) 5 drives in RAID6 set, 200gb for host OS, rest for VM storage. 1 drive for hot swap - this is how it is currently setup 2) 4 drives in RAID10 set, 200gb for host OS, rest for VM storage. 2 drives for hot swap 3) 4 drives in RAID10 set for VM storage, 2 drives in RAID1 set for host OS. No drives for hot swap - While this is probably the best option with the amount of drives I have, I don't like the idea of having no hot swap 4) 3 drives in RAID6 set for VM storage, 2 drives in RAID1 set for host OS. 1 drive for hot swap All options give us enough storage capacity for our files, etc. We don't have any budget for extra drives or extra hot swap HD chassis for the servers. We have about 70 clients and about 150 users. MAIN SERVER Intel Xeon 5520 @ 2.27 GHz (2 processors) 16GB RAM 6 x 1TB Seagate Barracuda ES.2 Enterprise SATA drives Intel SRCSATAWB RAID controller Virtual machine workload using Hyper-V on Windows Server 2008 R2: DC01 - Active Directory Domain Controller / DNS server / Global catalog - 1GB RAM DC02 - Active Directory Domain Controller / DNS server / Global catalog - 1GB RAM Member Server - DHCP server, File server, Print server - 1GB RAM SCCM Member Server - 4GB RAM Third Party Software Member Server - A/V server, Ticketing software, etc - 4GB RAM Exchange 2007 - 4GB RAM - however we are probably migrating to a hosted solution, therefore freeing up resources BACKUP SERVER Intel Xeon E5410 @ 2.33GHz (2 processors) 16GB RAM 6 x 2TB WD RE4 SATA drives Intel SRCSASRB RAID controller Virtual machine workload using Hyper-V on Windows Server 2008 R2: AppAssure backup software - 8GB RAM

  Read the article

• How to enjoy DVD on Apple iPad

  - by user44251

  I believe many people spent a sleepless night yesterday waiting for the new Apple Tablet to come, just a few days ago or perhaps longer I noticed fierce debate about it, its name, size, capacity, processor, main features, price etc. And now, they can take a long breath with the new Apple Tablet named iPad officially released on 28, January, 2010 (Beijing Time). But I know a new battle just begins. iPad, sounds somewhat like iPod and it really shares some similarities in terms of shape like smart, light and portable. It has a 9.7-inch, LED-backlit, IPS display with a remarkable precise Multi-Touch screen. And yet, at just 1.5 lbs and 0.5 inches thin, it's easy to carry and use everywhere. It can greatly facilitates your experience with the web, emails, photos and videos. Right now, it can run almost 140.000 of the apps on the Apple store. It can even run the apps you have downloaded for your iPhone or iPod touch. But so far, I haven't seen any possibility that it can work with DVD, probability there is no built-in DVD-ROM or DVD player which can play DVD directly. As Apple iPad states, the video formats supported are MPEG-4 (MP4, M4V), H.264, MOV etc and audio formats accepted are AAC, Proteceted AAC, MP3, AIFF and WAV etc, those are formats that are commonly used with iMac. This could really a hard nut to crack if you want to watch your favourite DVD on this magic Apple iPad. But don't worry, there is still way out, you just need a few steps for ripping and importing DVD movies to Apple iPad with a simple application DVD to iPad converter What's on DVD to iPad Converter for Mac DVD to iPad converter for Mac is a powerful and professional application designed for the newly released Apple iPad which can rip, convert your DVD contents to Apple iPad compatible MPEG-4 (MP4, M4V), H.264, MOV etc, and other popular file formats like AVI, WMV, MPG, MKV, VOB, 3GP, FLV etc can also be converted so that you can put on your portable devices like iPod, iPhone, iRiver, BlackBerry etc. Besides, it can also extract audio from DVD videos and save as MP3, AIFF, AAC, WAV etc. Mac DVD to iPad converter has also been enhanced that can run both on PowerPC and Intel (Snow Leopard included). It can offer versatile editing features which allows you to make your own DVD videos. For example, you can cut your DVD to whatever length you like by Trim, crop off unwanted parts from DVD clips by Crop, add special effect like Gray, Emboss and Old film to make your videos more artistic. Besides, its built-in merging feature and batch mode allows you to join several DVD clips into a single one and do batch conversion. And more features can be expected if you afford a few minutes to try.

  Read the article

< Previous Page | 437 438 439 440 441 442 443 444 445 446 447 448  | Next Page >