Search Results

Search found 16530 results on 662 pages for 'off shore'.

Page 462/662 | < Previous Page | 458 459 460 461 462 463 464 465 466 467 468 469  | Next Page >

• How to rescue from an SD (SDHC) card that I can't reformat (possible hardware failure)

  - by sbwoodside

  I have a transcend 16GB SDHC card and a lot of photos on it that I'd like to recover. When I plug it into the SD card reader, it takes a while for the Mac to even recognize that there's a disk present, and it shows up as 1.07GB with geometry 520/64/63 (according to fdisk). First I tried file recovery: PhotoRec: no files are found (the images are in CR2 format and I'm using testdisk-6.14-WIP which claims to recognize that format under TIF) dd / ddrescue: they create a 1.07GB image, same problem as above TestDisk: doesn't find any partitions to recover I found a source saying that the correct geometry for this type of SD Card is Heads 255, Sectors/Track 63, Cylinders 1953, so I tried manually setting that geometry in PhotoRec/TestDisk. No improvement. Next I tried formatting the disk with fdisk. After writing and quitting, I ran fdisk again and it reported that the new format hadn't been saved on the disk. I also tried resetting the format/partitions with TestDisk and that failed also. The fdisk log is below. I don't really care about the card, I've already ordered a new SanDisk card. But I'd like to get the data off. Maybe, is there any way to force dd or some other tool to create an image of the disk based on the original geometry and not on what the card "thinks" its geometry is? Or am I missing something?

  Read the article

• Can I have a single solid state drive and a RAID array on the same machine?

  - by jaminto

  Hi- To summarize, i'm looking to use a single solid state drive as my primary drive, and two conventional sata drives in a RAID 1 configuration for data. I am trying to install 64-bit Windows 7 onto this configuration. Is this possible? Here are the details: I built a desktop that has been running 64-bit Vista on two 500Gb in a RAID 1 array for a few years. I just purchased an Intel X25-M 80Gb Sata Solid-State Drive, and was planning on using this a my primary drive, and keeping the RAID 1 array as my data drive. I added the SSD drive and in the RAID setup, configured it as a RAID 0 array of only one disk. Then, I tried to do a clean install of windows 7 64-bit, but got stuck in the "Missing driver for CD/DVD drive" black hole of selecting driver files and Windows telling me that i don't have the appropriate driver for my hardware. The missing hardware is NOT a CD/DVD drive, since i'm installing off of my only CD/DVD drive. Plus at one point i was able to point it at a driver for my raid controller, and then my hard drives magically showed up as browsable sources for finding drivers for some other unnamed device that setup couldn't recognize. After a few hours of trying drivers (this was a very slow process) i decided to reboot and look at the BIOS settings. I'm using an ASUS M2A-VM motherboard which has an ATI SB600 RAID controller on board. I switched the "On board SATA Type" setting from "SATA" to "AHCI" thinking that since AHCI is an Intel thing, this would help. Unfortunately, this abandoned my RAID configuration, and my previously mirrored drives are showing up as separate drives when i boot into my current windows installation. Am i trying to do the impossible here? Should i just buy a separate SATA/RAID PCI card and plug the SSD into that? Any help would be greatly appreciated.

  Read the article

• Acer Aspire One getting extremely hot

  - by ascom

  I have an Acer Aspire One D250-1197. I really better type fast before it overheats again... For some reason, I'm having a problem with heat on my netbook only when I run Joli OS (Ubuntu 9.10 LTS?). When I leave it idle, with nothing running (other than the regular Joli OS desktop and a couple of doing-nothing terminals), heat slowly builds up to the point where the netbook is burning hot to the touch. I have never had this problem when running Windows 7 Starter (even though it gives me plenty of other headaches). It seems that the fan is spinning, but not fast enough to keep up with the heat buildup. Is there something wrong with the fan drivers? The computer doesn't seem to recognize that it is overheating. What can I do to solve this problem (other than shut it off or use Windows)? I'm currently on the wrong side of Earth (I mean, on vacation), so I just need a temporary fix, such as a driver I can install. Also, I have to use Linux, because I have to share out the wired connection in hotels wirelessly to the iPhones. EDIT: I'm switching from Joli OS to a more "proper" and up to date distribution (Xubuntu 13.04). I'll see if it still has the heat problem and try @nod's cpufreq idea.

  Read the article

• client flips between internal and external IP addresses??

  - by jmiller-miramontes

  I have what seems like a not-particularly-complicated home network, all things considered: a DSL line comes in to a modem/router, which goes off to a switch, which supports a bunch of machines. My machines live in a 192.168.0.x address space; however, I'm running some public servers on the network, so I have a block of 8 (5, really) static IP addresses that are mapped to the servers by the router. The non-servers get 192.168.0.x addresses via NAT; some machines have static addresses and some get addresses from DHCP. Locally, I'm running a DNS server (named) to map between the domain names and the 192.168 address space. Somewhat messy, but everything basically works. Except: One of my local non-server clients occasionally switches from its internal address to its external address. That is, if I check the logs of a website I'm running internally, the hits coming from this client sometimes show up with the internal 192.168 address, and sometimes with the external (216.103...) address. It will flip back and forth for no apparent reason, without my doing anything. This can be a problem in terms of how the clients interact with the way I have some of the clients' SSH systems configured (e.g., allowing access from the internal network but not the external network), but it also Just Seems Wrong. I will confess that I'm kinda skating on the very edge of my networking competence here, but I can't for the life of me figure out what's going on. If it helps, the client in question is running Mac OS X / 10.6; its address is statically assigned, is not one of the five externally-accessible addresses, and gets its DNS from (first) the internal DNS server and (second) my ISP's DNS servers. I can't swear that none of the other NAT clients are also showing this problem; the one I'm dealing with is my everyday machine, so this is where I run into it. Does anybody out there have any advice? This is driving me crazy...

  Read the article

• Domain Environment + Certificate Authority + Server 2008 R2

  - by user1110302

  I have recently been delegated the task to setup a CA in our domain environment and have a question on why Microsoft does somethings the way they do lol. I have been trying to read up on what the best practices are for going about this task, and have decided that in an ideal CA environment you should have one “offline” Root CA, and then two subordinate CAs for redundancy/issuing the certs. That is all good, I understand how this works and why, but in messing with a sandbox I have setup, the way you go about adding certificate authorities to a domain environment seems extremely trivial and against all of their best practices… Dooes anyone know what the purpose is of an Enterprise Root CA that is integrated into Active Directory? From what I have read, once you setup an Enterprise Root CA that is integrated into Active Directory, it stays with Active Directory for the long haul and must not be turned off/renamed/touched under any circumstances. If this is true, that seems to go against the practice of setting up a standalone root CA, adding the subordinates, and then taking the root offline. Thanks for any feedback you may have to offer!

  Read the article

• Toshiba Qosmio: Battery Stuck at 60%, does not Charges, PC can't power up, can't remain on with out

  - by Fellknight

  Just like the tittle says, now let me try to give some more detail about the symptoms; The battery is stuck at 60 percent (68% at the moment of this writing).When hovering over the battery icon in Windows 7 Home Premium x64 it reads:"68% available (plugged in, charging)", there's no x or any sing the OS is displaying any error. No matter how much time left connected to the AC adapter the battery doesn't charge, it seems however it continues to discharge at its normal rate when disconnected from the laptop (about 1% each 2 weeks). Now this last symptom is the one i find most strange it "seems" the laptop somehow isn't recognizing the battery because even with the remaining charge of 60%(ish) the laptop wont power up or remain on if disconnected from its AC adapter(if it's on and is unplugged it will immediately turn off). Meaning that even with the battery attached correctly in its right place is as if running the laptop with no battery at all. Toshiba's Utilities haven't detected anything strange (or anything for that matter) with the battery or the hardware. The laptop when in use is connected 90% of the time to a Belkin surge protector (like my 1TB EHD). The protector is working correctly (green light on) and the 1TB HD too, thus a power surge having damaged it's very unlikely. Thnx in advance

  Read the article

• How to bypass resume from hibernate

  - by Daniel Trebbien

  I am attempting to resume a Windows Vista laptop from hibernate, but the resume process seems to be stuck in an endless loop in which Windows is repeatedly trying to read from the optical drive. When I press the Power On button on the laptop, the screen is black (not even the backlight turns on) and the following occurs in a loop: Five seconds pass and I hear the optical drive being accessed. (There's no disk in the drive, so it sounds like a short buzzing noise.) Two seconds pass and I hear the optical drive being accessed. Two seconds pass and I hear the optical drive being accessed. So it's three short buzzing noises in a row, over and over again. Eventually I have to abruptly power off the machine. I have tried inserting a data CD into the drive as well as a bootable CD (a live Linux distro boot disk). For both, the optical drive spins up for a bit, but stops after Windows decides that the disk is not what it is looking for. I have since lost the Windows Vista recovery DVD, but I don't know if inserting the recovery disk into the optical drive would have a different effect than the bootable CD. I have tried pressing F8 immediately after pressing the Power On button (hoping to enter System Restore), but that did not have an effect. Is there a special key sequence that will cause Windows to bypass resuming from hibernate, effectively ignoring hiberfil.sys?

  Read the article

• Cannot get SCVMM Admin Console to Connect to Hyper-V Server 2008 R2

  - by user63250

  I cannot get SCVMM Admin console to connect to Hyper-V Server 2008. I have changed all firewall settings on the server to allow for a connection, I have even tried turning the firewall off completely. I am getting this error message: Unable to connect to the Virtual Machine Manager server xx.xxx.xxx.xx. the Virtual Machine Manager service on that servier did not respond. Verify that Virtual Machine Manager has been installed on the server and that the Virtual Machine Manager service is running. Then try to connect again. If the problem persists, restart the Virtual Machine Manager Service. ID: 1602 I have tried restarting the VMMS service, and that did not work. I have posted a similar question to this before, and was told to make sure to intall the Hyper-V agent on the Hyper-V server. I was told that SCVMM can push the agent out to the server. However, if I cannot connect to the server, how can I use SCVMM to push out the agent? Thanks for any help.

  Read the article

• Editing a windows XP installation's registry without being able to log in.

  - by Alain

  I've got a windows XP installation that has a corrupt registry. A worm (which was removed) had hijacked the HKLM\Software\Microsoft\Windows NT\CurrentVersion\Winlogon entry (which should have a value of Userinit=C:\windows\system32\userinit.exe When the worm was removed, the corrupt entry was deleted entirely, and now the system automatically logs off immediately after attempting to log in. Regardless of the user and boot mode, no accounts can be logged in to. The only thing required to correct this behavior is to restore the registry key, but I cannot come up with any ways of editing the registry without logging in to an account. I tried remotely connecting to the registry but the required services aren't enabled on the machine. I tried booting on the same machine using the BartPE boot CD but I could not find any way of editing the registry on the C:\Windows installation - running regedit only modifies the X:\I386\ registry in memory. So, what can I use modify the registry of an un-login-able Windows XP instance so that I can log in again? Thanks guys. EDIT: The fix worked. The solution to the auto-logoff problem was, as hoped, to simply add the value mentioned above to the appropriate registry entry. This can be done using the BartPE Boot CD, as described in the accepted answer below, but I used the Offline NT Registry Editor software mentioned in another answer. The steps were: Boot from the NT Registry Editor CD Follow the directions until the appropriate boot sector is loaded. Instead of using one of the default options for modifying passwords or user accounts, type "software" to edit that hive. Type '9' to enter the command line based registry editor. Type "cd Microsoft" (enter) "cd Windows NT" (enter) "cd CurrentVersion" (enter) "cd Winlogon" (enter) Type "nv 1 Userinit" to create a new value under the Winlogon key Type "ev Userinit" to edit the new value, and when prompted, type "C:\windows\system32\userinit.exe" (enter) Type 'q' to quit the registry editor, and as you back out of the system, follow directions to write the hive back to disk. Restart your computer and log in - problem solved. (generic 'warning: back up your registry' disclaimer)

  Read the article

• Performance of Virtual machines on very low end machines

  - by TheLQ

  I am managing a few cheap servers as my user base isn't large enough to get much more powerful servers. I also don't have the money lying around to invest in a server to prepare for the larger user base. So I'm stuck with the old hardware I have. I am toying with the idea of virtualizing all the current OS's with most likely VMware vSphere Hypervisor (AKA ESXi) Xen (ESXi has too strict of an HCL, and my hardware is too old). Big reasons for doing so: Ability to upgrade and scale hardware rapidly - This is most likely what I'll be doing as I distribute services, get a bigger server, centralize (electricity bills are horrible), distribute, get a bigger server, etc... Manually doing this by reinstalling the entire OS would be a big pain Safety from me - I've made many rookie mistakes, like doing lots of risky work on a vital production server. With a VM I can just backup the state, work on my machine, test, and revert if necessary. No worries, and no OS reinstallation Safety from other factors - As I scale servers might go down, and a backup VM can instantly be started. Various other reasons. However the limiting factor here is hardware. And I mean very depressing hardware. The current server's run off of a Pentium 3 and 4, and have 512 MB and 768 MB RAM respectively (RAM can be upgraded soon however). Is the Virtualization layer small enough to run itself and a Linux OS effectively? Will performance be acceptable (50% CPU overhead for every operation isn't acceptable)? Does it leave enough RAM for the Linux OS? Is this even feasible?

  Read the article

• Browsers hang when loading web pages

  - by avalanchis

  HP Laptop with Windows Vista Home Premium, Service Pack 2. Problem affects IE8 and Firefox. When attempting to browse most web sites, browser loads web site title in browser's title bar, then displays "Waiting for site url" and never completes loading the page. Able to connect to www.google.com with no problems. Unable to connect to www.carbonwy.com, www.wsj.com, www.cnn.com, www.microsoft.com, etc. Other PCs on same subnet are all able to connect to these sites without any problem. nslookup resolves all of these sites without any problem, so DNS does not appear to be the problem. Windows Firewall is disabled. Norton 360 was previously installed but has been uninstalled. No other firewall software is installed. IE8 Protected Mode is off. IE8 advanced settings have been reset. IE8 user settings have been reset. After reset, IE8 tries to connect to http://hp-laptop.aol.com and go.microsoft.com but same symptoms persist. Title bar loads, then nothing. System has been restarted numerous times. Running out of ideas. Please help!

  Read the article

• DNS setup problems with Windows Azure VPS

  - by jbigelow

  What is the proper to setup the A record (or CNAME) for a Windows Azure VPS? I can't connect to my website after setting up IIS and believe I don't have the correct DNS setup. I created a small VPS instance with the default Windows Server 2012 configuration. I RDP'd in and added the Webserver role. In my DNSMadeEasy control panel I added an A record with my Public Virtual IP Address. In IIS I went to the default website and added bindings for the hostname of my website, so I should be able to type mywebsite.com and see the IIS 8 splash screen, but instead my browser cannot connect. I attempted to navigate to the site by typing in my Virtual IP address into the browser and still cannot connect. I RDP'd back into the machine and turned off Windows Firewall. No change, still cannot navigate to my website. From within IIS I double checked my binding. If I click "browse *:80" I can bring up my website in IE with the http:// localhost address. If I click "browse mywebsite on *.80" IE says "This page cannot be displayed.", from within the RDP session I can view the site if I navigate to http:// 127.0.0.1 but not if I navigate to my Virtual IP, nor can I view the page if I try navigating to http:// mywebservername.cloudapp.net I'm thinking I must be fundamentally not understanding how do DNS setup with Azure VPS but my initial Google searches aren't turning up any helpful information. (spaces added after the http:// so serverfault doesn't try and render them as valid urls.)

  Read the article

• Cannot access SMC8014WG-SI provided by TimeWarner/RoadRunner administrative interface...

  - by Matt Rogish

  I just received installation of RoadRunner internet/TV/Voice and I was given a wi-fi router from the TimeWarner folks. The model is a SMC SMC8014WG-SI. Unfortunately, the password it uses is WEP and that is, as we all know, completely insecure. The tech that was here didn't know how to change it to something like WPA2 w/TKIP, and I was on hold for 20 minutes with the TimeWarner folks before I gave up. My problem is that the default web interface (http://192.168.0.1) isn't responding. I can ping it, I can access the internet through it, but I can't get to the admin interface. I did a "hard reset" of the device but still no dice. My suspicion is that the wi-fi admin interface is disabled (a common setting) but the wired interface isn't working on either of my two laptops (I've tried two laptops with two different cables, no link light activated). Am I SOL? Did they lock this down so I can't do what I want to do? Worst-case is I just hook up my go-to WRT54G router to the other modem and leave this one turned off, but I'd rather use their hardware to avoid any "It's not our problem" in the future. Any thoughts? Thanks!!

  Read the article

• Flash Media Server won't run on RHEL 6.2 EC2 instance - _defaultRoot__edge1 experienced 1 failure

  - by edoloughlin

  I've got a fresh Redhat Enterprise 6.2 64-bit instance on EC2. I've turned off the firewall and have installed an FMS 4.5 dev server. The FMS install failed, complaining about a missing libcap.so until I installed the libcap.i686 package. The following libcap packages are now installed: libcap.i686 2.16-5.5.el6 @rhui-us-east-1-rhel-server-releases libcap.x86_64 2.16-5.5.el6 @koji-override-0/$releasever libcap-ng.x86_64 0.6.4-3.el6_0.1 @koji-override-0/$releasever libpcap.x86_64 14:1.0.0-6.20091201git117cb5.el6 In the logs directory I have admin and master logs (only). The admin logs look ok: #Fields: date time x-pid x-status x-ctx x-comment 2012-02-29 09:24:26 1144 (i)2581173 FMS detected IPv6 protocol stack! - 2012-02-29 09:24:26 1144 (i)2581173 FMS config <NetworkingIPv6 enable=false> - 2012-02-29 09:24:26 1144 (i)2581173 FMS running in IPv4 protocol stack mode! - 2012-02-29 09:24:26 1144 (i)2581173 Host: ip-10-204-143-55 IPv4: 10.204.143.55 - 2012-02-29 09:24:26 1144 (i)2571011 Server starting... - 2012-02-29 09:24:26 1144 (i)2631174 Listener started ( FCSAdminIpcProtocol ) : localhost:11110/v4 - 2012-02-29 09:24:27 1144 (i)2631174 Listener started ( FCSAdminAdaptor ) : 1111/v4 - 2012-02-29 09:24:28 1144 (i)2571111 Server started (./conf/Server.xml). - I can't connect an RTMP client to the FMS. The master logs contain these lines, repeating every 5 seconds: 2012-02-29 10:43:17 1076 (i)2581226 Edge (2790) is no longer active. - 2012-02-29 10:43:17 1076 (w)2581255 Edge (2790) _defaultRoot__edge1 experienced 1 failure[s]! - 2012-02-29 10:43:17 1076 (i)2581224 Edge (2793) started, arguments : -edgeports ":1935,80" -coreports "localhost:19350" -conf "/opt/adobe/fms/conf/Server.xml" -adaptor "_defaultRoot_" -name "_defaultRoot__edge1" -edgename "edge1". -

  Read the article

• Setting up AJP with JBoss 7

  - by purlogic

  I have two different versions of JBoss on a server, JBoss 6.0 Final and JBoss 7.0.2. I can one run or the other by switching a couple of sym links and issuing a "service jboss start" command. I am, by no means, an expert in JBoss, however JBoss 6.0 appears to have AJP running out of the box with no initial configuration required on port 8009. With JBoss 7, however, I had to vi the file "standalone/configuration/standalone.xml" and add a few entries. Those entries are: In the <subsystem /> tag, I added: <connector name="ajp" protocol="AJP/1.3" socket-binding="ajp" /> In the <socket-binding-group /> tag I added: <socket-binding name="ajp" port="8009"/> Then in Apache's configuration file (httpd.conf), I added: <Proxy *> AddDefaultCharset Off Order deny,allow Allow from all </Proxy> ProxyPass /app ajp://localhost:8009/app ProxyPassReverse /app ajp://localhost:8009/app AJP proxying works with 6, not with 7... I assume it's because I haven't properly set up AJP in JBoss 7 and not entirely sure how to do that. I have searched documentation on their site with not a lot of specifics on how to do so. Any help or insight into setting up AJP with JBoss 7 would be much appreciated!!

  Read the article

• Connect bluetooth headphones both to PC and phone at the same time

  - by Sergiy Byelozyorov

  I have recently bought Philips SHB6110. Extract from the 13th page of manual: Therefore you can connect your Bluetooth stereo headset. with a Bluetooth stereo enabled phone to both listen to music and lead calls, or with a Bluetooth phone that does not support Bluetooth stereo (A2DP) to lead calls and at the same time to a Bluetooth audio device (Bluetooth enabled MP3 player, Bluetooth audio adapter etc.) to listen to music. Make sure to pair the phone first with your Bluetooth headset, then turn both the phone and headset off to then pair the Bluetooth audio device. With the SwitchStream feature you can listen to music and monitor your calls at the same time. Even while listening to music, you will hear a ring tone when receiving a call and can switch to the call simply by tapping the button. The manual however doesn't specify how do I connect to both device at the same time. I use Toshiba Satellite Pro P300-1CG laptop with Belkin Mini Bluetooth Adapter and Nokia N95 phone. Operating system is Windows 7 64-bit and I have Skype installed. Both phone and compute can be used for listening to music and talking on the phone (on PC via Skype). Best solution would be if I could connect to PC and phone as the same time and monitor calls both mobile and Skype calls while listening music from Winamp. If that is not possible, then I would like at least to be able to listen music from PC, while monitoring calls from mobile. So, please tell me how do I connect both PC and phone to headphones?

  Read the article

• New Computer freezing up at random

  - by Benjamin Frost

  Since I built my system about 4 weeks ago I'v been getting random freezes, Sometimes it can happen directly after startup and sometimes it wont freeze up for 3-4 days of 24/7 running. It seems to be happening under all stress loads but mainly when the CPU is under 10% load. It doesn't give me a BSOD or anything, it simply just freezes and repeats the last sound before the freeze until I shut it down by the power button. I'v re-seated everything in the system except the CPU, Cleaned the RAM sockets and gold fittings. None of the components have been clocked above their factory settings as of yet, don't want to overclock them until I sort out these freezes. Temps are all well under the rated max temps, the highest the temps have been are below CPU: Low load: 16-21°C Full Load (100%) 40-43°C *(From HWMonitor by CPUID) GPU 1: Low Load: 25-30°C Full Load (100%): 45-50°C GPU 2: Low Load: 23-27°C Full Load (100%): 45-50°C *(GPU Temps from Catalyst Control Center) General Case temps Rear: 18-20°C Mid: 20-21°C Front (HDD/SSD Bays): 14-19°C (Case temps may be a little off as it's from the Kaze master pro fan controller) I have Un-installed EVERY driver for Motherboard, GPU & Soundcard and Re-installed twice. Windows is all up to date. To date i'v tried the following Running Memtest for 24 hrs straight, No errors Running Memtest on each individual RAM modules, No errors Reseated everything except the CPU Cleaned DIMM Sockets and Gold inputs Tested the Graphics cards 1 at a time Re-arranged all the SATA devices to run on Chipset controlled ports Re-installing all drivers OS: Win7 Professional 64bit Motherboard: ASRock X79 Extreme9 CPU: i7 3930k 3.2GHz GPU: Sapphire 7950 OC Edition V2 (2 card Crossfire) RAM: G.Skill Ripjaws Z F3-17000CL11Q-16GBZL 16GB (4x4GB) DDR3 Boot Drive: OCZ Agility 4 128GB Data Drive 1: Western Digital Black 2TB Data Drive 2: Western Digital Black 2TB Data Drive 3: Western Digital Green 3TB Power Supply: Corsair AX1200 Gold

  Read the article

• Facebook Chat through XMPP protocol on Pidgin Portable - Will not Authorize

  - by Sara Neff

  I heard you can use facebook chat on desktops now. Thats awsome! What i didn't hear is that it is a pain in the butt! Not awsome! I've followed six nearly identical sets of instructions from six different websides, including the one that facebook generates for you, to get facebook chat connected through Pidgin. Its the latest portable version, so from what i hear the plugin is out of the question. Whenever I go to try and connect i get a message saying "Not Authorized" and buttons to either modify the account info, or retry. NOTHING i have done has fixed this, and I can't find anything remotely usefull anywhere. I am running windows xp, and running pidgin (portable) off of a flash drive. Someone please tell me what i have to do. I read about authorizing the chat on my actual facebook page. I'd have tried that if i could find out how to do it, but if its there they hid it good. HELP?!

  Read the article

• nginx+mysql5 loadtesting configuration strangeness

  - by genseric

  i am trying to setup a new server running on debian6 and trying to make it work smooth under load. i ve used a wordpress site as a test object, and tried the configurations on http://blitz.io. when i increase the mysql max_connections from 50 to 200 lots of timeouts start to occur. but on 50 , no timeouts and pretty well response times. nginx configuration is fine , i tuned the config so i dont see errors. so i presume it's related to the other configuration options of my.cnf . i read some about options but still cant find what max_connections problem is all about. btw, the server has 16gb of ram and a fine i7 cpu. here is the current my.cnf [client] port = 3306 socket = /var/run/mysqld/mysqld.sock [mysqld_safe] socket = /var/run/mysqld/mysqld.sock nice = 0 [mysqld] wait_timeout=60 connect_timeout=10 interactive_timeout=120 user = mysql pid-file = /var/run/mysqld/mysqld.pid socket = /var/run/mysqld/mysqld.sock port = 3306 basedir = /usr datadir = /var/lib/mysql tmpdir = /tmp language = /usr/share/mysql/english skip-external-locking bind-address = 127.0.0.1 key_buffer = 384M max_allowed_packet = 16M thread_stack = 192K thread_cache_size = 20 myisam-recover = BACKUP max_connections = 50 table_cache = 1024 thread_concurrency = 8 query_cache_limit = 2M query_cache_size = 128M expire_logs_days = 10 max_binlog_size = 100M [mysqldump] quick quote-names max_allowed_packet = 16M [mysql] #no-auto-rehash # faster start of mysql but no tab completition [isamchk] key_buffer = 16M thanks in advance. i asked this question on SO but it's closed as off topic so i believe this is a SF question.

  Read the article

• SSH over HTTPS with proxytunnel and nginx

  - by Thermionix

  I'm trying to setup an ssh over https connection using nginx. I haven't found any working examples, so any help would be appreciated! ~$ cat .ssh/config Host example.net Hostname example.net ProtocolKeepAlives 30 DynamicForward 8118 ProxyCommand /usr/bin/proxytunnel -p ssh.example.net:443 -d localhost:22 -E -v -H "User-Agent: Mozilla/4.0 (compatible; MSIE 6.0; Win32)" ~$ ssh [email protected] Local proxy ssh.example.net resolves to 115.xxx.xxx.xxx Connected to ssh.example.net:443 (local proxy) Tunneling to localhost:22 (destination) Communication with local proxy: -> CONNECT localhost:22 HTTP/1.0 -> Proxy-Connection: Keep-Alive -> User-Agent: Mozilla/4.0 (compatible; MSIE 6.0; Win32) <- <html> <- <head><title>400 Bad Request</title></head> <- <body bgcolor="white"> <- <center><h1>400 Bad Request</h1></center> <- <hr><center>nginx/1.0.5</center> <- </body> <- </html> analyze_HTTP: readline failed: Connection closed by remote host ssh_exchange_identification: Connection closed by remote host Nginx config on the server; ~$ cat /etc/nginx/sites-enabled/ssh upstream tunnel { server localhost:22; } server { listen 443; server_name ssh.example.net; location / { proxy_pass http://tunnel; proxy_set_header Host $host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_redirect off; } ssl on; ssl_certificate /etc/ssl/certs/server.cer; ssl_certificate_key /etc/ssl/private/server.key; } ~$ tail /var/log/nginx/access.log 203.xxx.xxx.xxx - - [08/Feb/2012:15:17:39 +1100] "CONNECT localhost:22 HTTP/1.0" 400 173 "-" "-"

  Read the article

• Apache ProxyPassReverse and https

  - by joshuaball

  Hi, I would like to map all traffic on 80 and 443 from foo.com to an internal server: 192.168.1.101. I have a VirtualHost (Apache 2.2 on Ubuntu) setup as follows (note, I had to break up the hyperlinks below because I am a 'new user'): <VirtualHost *:80> ServerName foo.com ServerAlias *.foo.com ProxyRequests Off ProxyPreserveHost On <Proxy *> Order deny,allow Allow from all </Proxy> ProxyPass / http://192.168.1.101/ ProxyPassReverse / http://192.168.1.101/ </VirtualHost> And that works great for http traffic. However, I can't seem to do the same thing for https. I have tried: Changing VirtualHost *:80 to * - but that doesn't work (I need it http-http and https-https) Creating a new VirtualHost entry for *:443 that redirects to http://192.168.1.101/, but that fails as well (browser timeouts) I did some searching, here and elsewhere, and the closest question I could find was this, but that didn't quite answer it. Also, just out of curiosity, I tried mapping all ports to https (by changing the two ProxyPass lines from http to https (and removing the :80 from VH), and that didn't work either. How would you do that as well? Any thoughts? Thanks in advance.

  Read the article

• Issues installing new drivers

  - by Luke

  I have a Windows XP Home SP3 system that won't detect anything on USB. It works on Ubuntu Live (off USB), and the USB keyboard and mouse work in the BIOS. Physically speaking, I'm sure it's fine. I installed the SMBus drivers and the USB driver from the motherboard's website, adn that went fine. If I plug anything in, it can detect the type of thing it is (i.e. keyboard, mouse, flash drive, etc) and even the name sometimes (i.e. Microsoft 5 button mouse), but won't accept any drivers. I have tried putting the Windows CD in the drive, but that didn't help. I have scanned for viruses and CHKDSK with no issues, and ran a MemTest86 with no issues. I am limited to one PS/2 connection for inputs, so I'm using the keyboard and haven't tried WU yet. A colleague suggested trying a new USB controller, so I put in a PCI one that only had drivers for 9x on the CD, so I assume that XP has them built in. It goes through the Found New Hardware wizard, but never actually finds drivers. I have also tried running SFC /SCANNOW and System Restore. SFC just flashes and goes away, making me believe it may be a hidden virus somewhere, but everything else seems to work, including MSE. I have reason to believe it's just an issue with detecting hardware, since even the USB Controller card can't seem to find drivers, but it can detect WHEN a USB device is connected Anyone else run into this, or have a suggestion short of re-installing Windows?

  Read the article

• A separate user for each task?

  - by Mark Tomlin

  I just got a VPS sver the other day, I'm new to server administration, but not that new to Ubuntu (11.04). I use it in my living room as the HTPC, and I had a previous VPS that I used on and off for a team speak server. This one I'm setting up for long term use. So I would like to know the best practice when it comes to websites and tasks that I have the server proforming. I understand that it could be beneficial to separate each website into it's own usergroup or under its own username. I would setup nginx so that it could read all of the users directors (and thus each website) but could not touch anything else. The same with the TeamSpeak, should I make a user for TeamSpeak so that it operates within its own confined area or is this overkill? I do have access to root on the sever and my current plan is to run about 4 websites and a TeamSpeak server. My stack is Linux (Ubuntu 11.04 LTS), nginx, and PHP 5.4.3 (using the PDO SQLite 3 built in driver for the database). Should PHP have it's own user group or is it ok to place it in with nginx?

  Read the article

• Time not propagating to machines on Windows domain

  - by rbeier

  We have a two-domain Active Directory forest: ourcompany.com at the root, and prod.ourcompany.com for production servers. Time is propagating properly through the root domain, but servers in the child domain are unable to sync via NTP. So the time on these servers is starting to drift, since they're relying only on the hardware clock. WHen I type "net time" on one of the production servers, I get the following error: Could not locate a time-server. More help is available by typing NET HELPMSG 3912. When I type "w32tm /resync", i get the following: Sending resync command to local computer The computer did not resync because no time data was available. "w32tm /query /source" shows the following: Free-running System Clock We have three domain controllers in the prod.ourcompany.com subdomain (overkill, but the result of a migration - we haven't gotten rid of one of the old ones yet.) To complicate matters, the domain controllers are all virtualized, running on two different physical hosts. But the time on the domain controllers themselves is accurate - the servers that aren't DCs are the ones having problems. Two of the DCs are running Server 2003, including the PDC emulator. The third DC is running Server 2008. (I could move the PDC emulator role to the 2008 machine if that would help.) The non-DC servers are all running Server 2008. All other Active Directory functionality works fine in the production domain - we're only seeing problems with NTP. I can manually sync each machine to the time source (the PDC emulator) by doing the following: net time \\dc1.prod.ourcompany.com /set /y But this is just a one-off, and it doesn't cause automated time syncing to start working. I guess I could create a scheduled task which runs the above command periodically, but I'm hoping there's a better way. Does anyone have any ideas as to why this isn't working, and what we can do to fix it? Thanks for your help, Richard

  Read the article

• Firefox and Chrome keeps forcing HTTPS on Rails app using nginx/Passenger

  - by Steve

  I've got a really weird problem here where every time I try to browse my Rails app in non-SSL mode Chrome (v16) and Firefox (v7) keeps forcing my website to be served in HTTPS. My Rails application is deployed on a Ubuntu VPS using Capistrano, nginx, Passenger and a wildcard SSL certificate. I have set these parameters for port 80 in the nginx.conf: passenger_set_cgi_param HTTP_X_FORWARDED_PROTO http; passenger_set_cgi_param HTTPS off; The long version of my nginx.conf can be found here: https://gist.github.com/2eab42666c609b015bff The ssl-redirect.include file contains: rewrite ^/sign_up https://$host$request_uri? permanent ; rewrite ^/login https://$host$request_uri? permanent ; rewrite ^/settings/password https://$host$request_uri? permanent ; It is to make sure those three pages use HTTPS when coming from non-SSL request. My production.rb file contains this line: # Enable HTTP and HTTPS in parallel config.middleware.insert_before Rack::Lock, Rack::SSL, :exclude => proc { |env| env['HTTPS'] != 'on' } I have tried redirecting to HTTP via nginx rewrites, Ruby on Rails redirects and also used Rails view url using HTTP protocol. My application.rb file contains this methods used in a before_filter hook: def force_http if Rails.env.production? if request.ssl? redirect_to :protocol => 'http', :status => :moved_permanently end end end Every time I try to redirect to HTTP non-SSL the browser attempts to redirect it back to HTTPS causing an infinite redirect loop. Safari, however, works just fine. Even when I've disabled serving SSL in nginx the browsers still try to connect to the site using HTTPS. I should also mention that when I pushed my app on to Heroku, the Rails redirect work just fine for all browsers. The reason why I want to use non-SSL is that my homepage contains non-secure dynamic embedded objects and a non-secure CDN and I want to prevent security warnings. I don't know what is causing the browser to keep forcing HTTPS requests.

  Read the article

< Previous Page | 458 459 460 461 462 463 464 465 466 467 468 469  | Next Page >