Search Results

Search found 13469 results on 539 pages for 'avoid trouble'.

Page 478/539 | < Previous Page | 474 475 476 477 478 479 480 481 482 483 484 485  | Next Page >

• How to connect SAN from CentOS through two iSCSI Targets

  - by garconcn

  I had asked the similar question before. This time I want to use subnet for two iSCSI Targets, hence I start a new question. I have an old Promise VTrak M500i SAN Server. It comes with 2 iSCSI ports. I want to connect to two LUNs on the SAN server through two separate Targets from CentOS 5.7 64bits server. My network setup is as follows: CentOS server: Management network - 192.168.1.1 Storage network 1 - 192.168.5.2 Storage network 2 - 192.168.6.2 Promise SAN server: Management network - 192.168.1.2 iSCSI Port 1 - 192.168.5.1 iSCSI Port 2 - 192.168.6.1 I have two Logical Drives on this SAN and they are mapped as follows: Index Initiator Name LUN Mapping 0 iqn.2011-11:backup (LD0,0) 1 iqn.2011-11:template (LD1,1) Basically, I want the traffic to iqn.2011-11:backup LUN 0 through 192.168.5.1 network the traffic to iqn.2011-11:template LUN 1 through 192.168.6.1 network I don't use MPIO, just want to separate the traffic to avoid traffic jam. How do I achieve this? I am new to SAN stuff, please explain as much detail as you can. Thank you. The following are what I am doing now. After mapping the LUN to my pre-defined Initiators, the CentOS server can discover both Targets. [root@centos ~]# iscsiadm -m discovery -t sendtargets -p 192.168.5.1 192.168.5.1:3260,1 iscsi-1 192.168.6.1:3260,2 iscsi-1 [root@centos ~]# iscsiadm -m discovery -t sendtargets -p 192.168.6.1 192.168.6.1:3260,2 iscsi-1 192.168.5.1:3260,1 iscsi-1 [root@centos ~]# /etc/init.d/iscsi start iscsid is stopped Starting iSCSI daemon: [ OK ] [ OK ] Setting up iSCSI targets: Logging in to [iface: default, target: iscsi-1, portal: 192.168.6.1,3260] Logging in to [iface: default, target: iscsi-1, portal: 192.168.5.1,3260] Login to [iface: default, target: iscsi-1, portal: 192.168.6.1,3260] successful. Login to [iface: default, target: iscsi-1, portal: 192.168.5.1,3260] successful. [ OK ] [root@centos ~]# iscsiadm -m session tcp: [1] 192.168.6.1:3260,2 iscsi-1 tcp: [2] 192.168.5.1:3260,1 iscsi-1 When I check the LUN mapping on the SAN server for the two Logical Drives, both LUNs are connected through Port0-192.168.5.2 with the Initiator defined in CentOS. Assigned Initiator List: Initiator Name Alias IP Address LUN iqn.2011-11.centos centos.mydomain.com Port0-192.168.5.2 0 Initiator Name Alias IP Address LUN iqn.2011-11.centos centos.mydomain.com Port1-192.168.5.2 1 I assume the following is what I want: Initiator Name Alias IP Address LUN iqn.2011-11.backup centos.mydomain.com Port0-192.168.5.2 0 Initiator Name Alias IP Address LUN iqn.2011-11.template centos.mydomain.com Port0-192.168.6.2 1

  Read the article

• multiple webapps in tomcat -- what is the optimal architecture?

  - by rvdb

  I am maintaining a growing base of mainly Cocoon-2.1-based web applications [http://cocoon.apache.org/2.1/], deployed in a Tomcat servlet container [http://tomcat.apache.org/], and proxied with an Apache http server [http://httpd.apache.org/docs/2.2/]. I am conceptually struggling with the best way to deploy multiple web applications in Tomcat. Since I'm not a Java programmer and we don't have any sysadmin staff I have to figure out myself what is the most sensible way to do this. My setup has evolved through 2 scenarios and I'm considering a third for maximal separation of the distinct webapps. [1] 1 Tomcat instance, 1 Cocoon instance, multiple webapps -tomcat |_ webapps |_ webapp1 |_ webapp2 |_ webapp[n] |_ WEB-INF (with Cocoon libs) This was my first approach: just drop all web applications inside a single Cocoon webapps folder inside a single Tomcat container. This seemed to run fine, I did not encounter any memory issues. However, this poses a maintainability drawback, as some Cocoon components are subject to updates, which often affect the webapp coding. Hence, updating Cocoon becomes unwieldy: since all webapps share the same pool of Cocoon components, updating one of them would require the code in all web applications to be updated simultaneously. In order to isolate the web applications, I moved to the second scenario. [2] 1 Tomcat instance, each webapp in its dedicated Cocoon environment -tomcat |_ webapps |_ webapp1 | |_ WEB-INF (with Cocoon libs) |_ webapp1 | |_ WEB-INF (with Cocoon libs) |_ webapp[n] |_ WEB-INF (with Cocoon libs) This approach separates all webapps into their own Cocoon environment, run inside a single Tomcat container. In theory, this works fine: all webapps can be updated independently. However, this soon results in PermGenSpace errors. It seemed that I could manage the problem by increasing memory allocation for Tomcat, but I realise this isn't a structural solution, and that overloading a single Tomcat in this way is prone to future memory errors. This set me thinking about the third scenario. [3] multiple Tomcat instances, each with a single webapp in its dedicated Cocoon environment -tomcat |_ webapps |_ webapp1 |_ WEB-INF (with Cocoon libs) -tomcat |_ webapps |_ webapp2 |_ WEB-INF (with Cocoon libs) -tomcat |_ webapps |_ webapp[n] |_ WEB-INF (with Cocoon libs) I haven't tried this approach, but am thinking of the $CATALINA_BASE variable. A single Tomcat distribution can be multiply instanciated with different $CATALINA_BASE environments, each pointing to a Cocoon instance with its own webapp. I wonder whether such an approach could avoid the structural memory-related problems of approach [2], or will the same issues apply? On the other hand, this approach would complicate management of the Apache http frontend, as it will require the AJP connectors of the different Tomcat instances to be listening at different ports. Hence, Apache's worker configuration has to be updated and reloaded whenever a new webapp (in its own Tomcat instance) is added. And there seems no way to reload worker.properties without restarting the entire Apache http server. Is there perhaps another / more dynamic way of 'modularizing' multiple Tomcat-served webapps, or can one of these scenarios be refined? Any thoughts, suggestions, advice much appreciated. Ron

  Read the article

• backup and restoration of a freeipa infrastructure

  - by Sirex

  I'm finding the documentation on ipa server backup and restoration sadly lacking, and being so centrally critical it's not something i'm really happy about shooting in the dark with - could some kind soul more knowledable in the matter please attempt to provide an idiot-proof guide to backing up and restoring of IPA server(s) ? Particularly the main server (the cert signing one). ...We're looking towards rolling out ipa in a two server setup (1 master, 1 replica). I'm using dns srv records to handle failover, hence a loss of the replica isn't a big deal as i could make a new one and force a resync to happen - it's losing the master that bothered me. The thing that i'm really struggling with is locating a step-by-step procedure for backing up and restoring the master server. I'm aware that whole-VM snapshot is the recommended way of doing IPA server backup, but that isn't an option at this time for us. I'm also aware that freeipa 3.2.0 includes some sort of backup command build in, but that isn't in the ipa version of centos, and i don't expect it will be for some time yet. I've been trying many different methods, but none of them seem to restore cleanly, amongst others, i've tried; a command similar to db2ldif.pl -D "cn=directory manager" -w - -n userroot -a /root/userroot.ldif the script from here to produce three ldif files -- one for the domain ({domain}-userroot), and two for the ipa server (ipa-ipaca and ipa-userroot): Most of the restores i've tried have been similar to the form of: ldif2db.pl -D "cn=directory manager" -w - -n userroot -i userroot.ldif which seems to work and reports no errors, but totally borks the ipa install on the machine and i can no longer login with either the admin password on the backed up server, or the one i set it to on installation before attempting the ldif2db command (i'm installing ipa-server and running ipa-server-install, then attempting the restore). I'm not overly bothered about losing the CA, having to rejoin the domain, losing replication etc etc (although it'd be awesome if that could be avoided) but in the instance of the main server dropping i'd really like to avoid having to re-enter all the user/group information. I guess in the instance of losing the main server i could promote the other one and replicate in the other direction, but i've not tried that, either. Has anyone done that ? tl;dr: Can someone provide an idiots guide to backing up and restoring an IPA server (preferably on CentOS 6) in a clear enough way that'd make me feel confident it'll actually work when the dreaded time comes ? Crayons are optional, but appreciated ;-) I can't be the only person struggling with this, seeing how widely used IPA is, surely ?

  Read the article

• Cannot join Win7 workstations to Win2k8 domain

  - by wfaulk

  I am trying to connect a Windows 7 Ultimate machine to a Windows 2k8 domain and it's not working. I get this error: Note: This information is intended for a network administrator. If you are not your network's administrator, notify the administrator that you received this information, which has been recorded in the file C:\Windows\debug\dcdiag.txt. DNS was successfully queried for the service location (SRV) resource record used to locate a domain controller for domain "example.local": The query was for the SRV record for _ldap._tcp.dc._msdcs.example.local The following domain controllers were identified by the query: dc1.example.local dc2.example.local However no domain controllers could be contacted. Common causes of this error include: Host (A) or (AAAA) records that map the names of the domain controllers to their IP addresses are missing or contain incorrect addresses. Domain controllers registered in DNS are not connected to the network or are not running. The client is in an office connected remotely via MPLS to the data center where our domain controllers exist. I don't seem to have anything blocking connectivity to the DCs, but I don't have total control over the MPLS circuit, so it's possible that there's something blocking connectivity. I have tried multiple clients (Win7 Ultimate and WinXP SP3) in the one office and get the same symptoms on all of them. I have no trouble connecting to either of the domain controllers, though I have, admittedly, not tried every possible port. ICMP, LDAP, DNS, and SMB connections all work fine. Client DNS is pointing to the DCs, and "example.local" resolves to the two IP addresses of the DCs. I get this output from the NetLogon Test command line utility: C:\Windows\System32>nltest /dsgetdc:example.local Getting DC name failed: Status = 1355 0x54b ERROR_NO_SUCH_DOMAIN I have also created a separate network to emulate that office's configuration that's connected to the DC network via LAN-to-LAN VPN instead of MPLS. Joining Windows 7 computers from that remote network works fine. The only difference I can find between the two environments is the intermediate connectivity, but I'm out of ideas as to what to test or how to do it. What further steps should I take? (Note that this isn't actually my client workstation and I have no direct access to it; I'm forced to do remote hands access to it, which makes some of the obvious troubleshooting methods, like packet sniffing, more difficult. If I could just set up a system there that I could remote into, I would, but requests to that effect have gone unanswered.) 2011-08-25 update: I had DCDIAG.EXE run on a client attempting to join the domain: C:\Windows\System32>dcdiag /u:example\adminuser /p:********* /s:dc2.example.local Directory Server Diagnosis Performing initial setup: Ldap search capabality attribute search failed on server dc2.example.local, return value = 81 This sounds like it was able to connect via LDAP, but the thing that it was trying to do failed. But I don't quite follow what it was trying to do, much less how to reproduce it or resolve it. 2011-08-26 update: Using LDP.EXE to try and make an LDAP connection directly to the DCs results in these errors: ld = ldap_open("10.0.0.1", 389); Error <0x51: Fail to connect to 10.0.0.1. ld = ldap_open("10.0.0.2", 389); Error <0x51: Fail to connect to 10.0.0.2. ld = ldap_open("10.0.0.1", 3268); Error <0x51: Fail to connect to 10.0.0.1. ld = ldap_open("10.0.0.2", 3268); Error <0x51: Fail to connect to 10.0.0.2. This would seem to point fingers at LDAP connections being blocked somewhere. (And 0x51 == 81, which was the error from DCDIAG.EXE from yesterday's update.) I could swear I tested this using TELNET.EXE weeks ago, but now I'm thinking that I may have assumed that its clearing of the screen was telling me that it was waiting and not that it had connected. I'm tracking down LDAP connectivity problems now. This update may become an answer.

  Read the article

• How to deny the web access to some files?

  - by Strae

  I need to do an operation a bit strange. First, i run on Debian, apache2 (which 'runs' as user www-data) So, I have simple text file with .txt ot .ini, or whatever extension, doesnt matter. These files are located in subfolders with a structure like this: www.example.com/folder1/car/foobar.txt www.example.com/folder1/cycle/foobar.txt www.example.com/folder1/fish/foobar.txt www.example.com/folder1/fruit/foobar.txt therefore, the file name always the same, ditto for the 'hierarchy', just change the name of the folder: /folder-name-static/folder-name-dinamyc/file-name-static.txt What I should do is (I think) relatively simple: I must be able to read that file by programs on the server (python, php for example), but if I try to retrieve the file contents by broswer (digiting the url www.example.com/folder1/car/foobar.txt, or via cUrl, etc..) I must get a forbidden error, or whatever, but not access the file. It would also be nice that even accessing those files via FTP are 'hidden', or anyway couldnt be downloaded (at least that I use with the ftp root and user data) How can I do? I found this online, be put in the file .htaccess: <Files File.txt> Order allow, deny Deny from all </ Files> It seems to work, but only if the file is in the web root (www.example.com / myfile.txt), and not in subfolders. Moreover, the folders in the second level (www.example.com/folder1/fruit/foobar.txt) will be dinamycally created.. I would like to avoid having to change .htaccess file from time to time. It is possible to create a rule, something like that, that goes for all files with given name, which is on www.example.com/folder-name-static/folder-name-dinamyc/file-name-static.txt, where those parts are allways the same, just that one change ? EDIT: As Dave Drager said, i could semplify this keeping those file outside the web accessible directory. But those directory's will contain others files too, images, and stuff used by my users, so i'm simply try to not have a duplicate folders system, like: /var/www/vhosts/example.com/httpdocs/folder1/car/[other folders and files here] /var/www/vhosts/example.com/httpdocs/folder1/cycle/[other folders and files here] /var/www/vhosts/example.com/httpdocs/folder1/fish/[other folders and files here] //and, then for the 'secrets' files: /folder1/data/car/foobar.txt /folder1/data/cycle/foobar.txt /folder1/data/fish/foobar.txt

  Read the article

• Broken cups installation on a ubuntu server 64

  - by user67046

  Hi, I am having trouble with an cups installation. It seems to be in a broken state. When i try to reinstall it it stalls, the same if i try to remove it completely. I am running the server version 64 bit of Ubuntu 10.10 with kernel Linux version 2.6.35-22-server. When i try to start the cups daemon with the following command sudo service cups start It just stays there and nothing happens. I have tried to remove it, to be able to reinstall it, with the following command sudo apt-get purge cups It finally stalls with the following message Removing cups ... After that nothing happens. The process tree for the apt-get command looks like this. 1404 1404 1404 ? 00:00:00 sshd 26495 26495 26495 ? 00:00:00 sshd 26581 26495 26495 ? 00:00:00 sshd 26582 26582 26582 pts/4 00:00:00 bash 27158 27158 26582 pts/4 00:00:00 apt-get 27172 27172 27172 pts/2 00:00:00 dpkg 27176 27172 27172 pts/2 00:00:00 cups.prerm 27178 27172 27172 pts/2 00:00:00 stop I have tried to leave the process running for a while to see if i get any error messages but without success. To get out of it I have to kill the processes. sudo dpkg --configure cups dpkg: error processing cups (--configure): package cups is already installed and configured Errors were encountered while processing: cups sudo dpkg --status cups Package: cups Status: purge ok installed Priority: optional Section: net Installed-Size: 8292 Maintainer: Ubuntu Developers <[email protected]> Architecture: amd64 Version: 1.4.4-6ubuntu2.3 Replaces: cupsddk-drivers (<< 1.4.0) Provides: cupsddk-drivers Depends: libavahi-client3 (>= 0.6.16), libavahi-common3 (>= 0.6.16), libc6 (>= 2.7), libcups2 (>= 1.4.4-3~), libcupscgi1 (>= 1.4.2), libcupsdriver1 (>= 1.4.0), libcupsimage2 (>= 1.4.0), libcupsmime1 (>= 1.4.0), libcupsppdc1 (>= 1.4.0), libdbus-1-3 (>= 1.0.2), libgcc1 (>= 1:4.1.1), libgnutls26 (>= 2.7.14-0), libgssapi-krb5-2 (>= 1.8+dfsg), libijs-0.35, libkrb5-3 (>= 1.6.dfsg.2), libldap-2.4-2 (>= 2.4.7), libpam0g (>= 0.99.7.1), libpaper1, libpoppler7, libslp1, libstdc++6 (>= 4.1.1), libusb-0.1-4 (>= 2:0.1.12), zlib1g (>= 1:1.1.4), debconf (>= 1.2.9) | debconf-2.0, upstart-job, poppler-utils (>= 0.12), procps, ghostscript, lsb-base (>= 3), cups-common (>= 1.4.4), cups-client (>= 1.4.4-6ubuntu2.3), ssl-cert (>= 1.0.11), adduser, bc, ttf-freefont, cups-ppdc Recommends: foomatic-filters (>= 4.0), cups-driver-gutenprint, ghostscript-cups Suggests: cups-bsd, foomatic-db-compressed-ppds | foomatic-db, hplip, xpdf-korean | xpdf-japanese | xpdf-chinese-traditional | xpdf-chinese-simplified, cups-pdf, smbclient (>= 3.0.9), udev Breaks: foomatic-filters (<< 4.0) Conflicts: cupsddk-drivers (<< 1.4.0) Conffiles: /etc/fonts/conf.d/99pdftoopvp.conf a5221cfad70a981c80864229ef56586d /etc/logrotate.d/cups 5bb41fa9900f0d1c565954405a2bd7c4 /etc/default/cups 2b436fbb1a32b82b6aba45a76a1d7e40 /etc/pam.d/cups ff2488324854f7b1e892bb0df062d5f0 /etc/init/cups.conf 1a3cd022e8474e3d2b44640f33ce68e3 /etc/ufw/applications.d/cups 29e98a6d850da251e180c3d68dec2bd3 /etc/apparmor.d/usr.sbin.cupsd 60c4b26bfd5c033baa3dd48a3b2e9911 /etc/cups/cupsd.conf e2c7ec15835ea0939e5e86f7c6efcc03 /etc/cups/snmp.conf 2326a8af1e112676d55245bc5eb459ca /etc/cups/cupsd.conf.default a68d54d76021e857dd1d64edf57d36c5 Description: Common UNIX Printing System(tm) - server The Common UNIX Printing System (or CUPS(tm)) is a printing system and general replacement for lpd and the like. It supports the Internet Printing Protocol (IPP), and has its own filtering driver model for handling various document types. . This package provides the CUPS scheduler/daemon and related files. Original-Maintainer: Debian CUPS Maintainers <[email protected]> Would be greatful if someone could provide some help on how to solve this issue.

  Read the article

• chkdsk, SeaTools, and "does not have enough space to replace bad clusters"

  - by Zian Choy

  When I tried to do a Windows Vista Complete PC Backup, I received an error message that blathered about bad sectors. Then, when I ran chkdsk /r on the destination drive, this is what I got: C:\Windows\system32>chkdsk /R E: The type of the file system is NTFS. Volume label is Desktop Backup. CHKDSK is verifying files (stage 1 of 5)... 822016 file records processed. File verification completed. 1 large file records processed. 0 bad file records processed. 0 EA records processed. 0 reparse records processed. CHKDSK is verifying indexes (stage 2 of 5)... 848938 index entries processed. Index verification completed. 0 unindexed files processed. CHKDSK is verifying security descriptors (stage 3 of 5)... 822016 security descriptors processed. Security descriptor verification completed. 13461 data files processed. CHKDSK is verifying file data (stage 4 of 5)... The disk does not have enough space to replace bad clusters detected in file 239649 of name . The disk does not have enough space to replace bad clusters detected in file 239650 of name . The disk does not have enough space to replace bad clusters detected in file 239651 of name . An unspecified error occurred.f 822000 files processed) Yet, when I ran the SeaTools short & long generic tests on the Seagate disk, I didn't receive any errors. I know that I could reformat the disk and try running chkdsk /r again but I'd prefer to avoid waiting 4 hours in the hope that the problem was magically fixed. On the other hand, if I RmA the drive to Seagate, I have no SeaTools error number to use and they may claim that the drive is just fine. What should I try to do next? Side frustration: There is plenty of free hard drive space. The E: partition has 182 GB free.

  Read the article

• Postfix SMTP auth not working with virtual mailboxes + SASL + Courier userdb

  - by Greg K

  So I've read a variety of tutorials and how-to's and I'm struggling to make sense of how to get SMTP auth working with virtual mailboxes in Postfix. I used this Ubuntu tutorial to get set up. I'm using Courier-IMAP and POP3 for reading mail which seems to be working without issue. However, the credentials used to read a mailbox are not working for SMTP. I can see from /var/log/auth.log that PAM is being used, does this require a UNIX user account to work? As I'm using virtual mailboxes to avoid creating user accounts. li305-246 saslauthd[22856]: DEBUG: auth_pam: pam_authenticate failed: Authentication failure li305-246 saslauthd[22856]: do_auth : auth failure: [user=fred] [service=smtp] [realm=] [mech=pam] [reason=PAM auth error] /var/log/mail.log li305-246 postfix/smtpd[27091]: setting up TLS connection from mail-pb0-f43.google.com[209.85.160.43] li305-246 postfix/smtpd[27091]: Anonymous TLS connection established from mail-pb0-f43.google.com[209.85.160.43]: TLSv1 with cipher ECDHE-RSA-RC4-SHA (128/128 bits) li305-246 postfix/smtpd[27091]: warning: SASL authentication failure: Password verification failed li305-246 postfix/smtpd[27091]: warning: mail-pb0-f43.google.com[209.85.160.43]: SASL PLAIN authentication failed: authentication failure I've created accounts in userdb as per this tutorial. Does Postfix also use authuserdb? What debug information is needed to help diagnose my issue? main.cf: # TLS parameters smtpd_tls_cert_file = /etc/ssl/certs/smtpd.crt smtpd_tls_key_file = /etc/ssl/private/smtpd.key smtpd_use_tls=yes smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache # SMTP parameters smtpd_sasl_local_domain = smtpd_sasl_auth_enable = yes smtpd_sasl_security_options = noanonymous broken_sasl_auth_clients = yes smtpd_recipient_restrictions = permit_sasl_authenticated,permit_mynetworks,reject_unauth_destination smtp_tls_security_level = may smtpd_tls_security_level = may smtpd_tls_auth_only = no smtp_tls_note_starttls_offer = yes smtpd_tls_CAfile = /etc/ssl/certs/cacert.pem smtpd_tls_loglevel = 1 smtpd_tls_received_header = yes smtpd_tls_session_cache_timeout = 3600s tls_random_source = dev:/dev/urandom /etc/postfix/sasl/smtpd.conf pwcheck_method: saslauthd mech_list: plain login /etc/default/saslauthd START=yes PWDIR="/var/spool/postfix/var/run/saslauthd" PARAMS="-m ${PWDIR}" PIDFILE="${PWDIR}/saslauthd.pid" DESC="SASL Authentication Daemon" NAME="saslauthd" MECHANISMS="pam" MECH_OPTIONS="" THREADS=5 OPTIONS="-c -m /var/spool/postfix/var/run/saslauthd" /etc/courier/authdaemonrc authmodulelist="authuserdb" I've only modified one line in authdaemonrc and restarted the service as per this tutorial. I've added accounts to /etc/courier/userdb via userdb and userdbpw and run makeuserdb as per the tutorial. SOLVED Thanks to Jenny D for suggesting use of rimap to auth against localhost IMAP server (which reads userdb credentials). I updated /etc/default/saslauthd to start saslauthd correctly (this page was useful) MECHANISMS="rimap" MECH_OPTIONS="localhost" THREADS=0 OPTIONS="-c -m /var/spool/postfix/var/run/saslauthd -r" After doing this I got the following error in /var/log/auth.log: li305-246 saslauthd[28093]: auth_rimap: unexpected response to auth request: * BYE [ALERT] Fatal error: Account's mailbox directory is not owned by the correct uid or gid: li305-246 saslauthd[28093]: do_auth : auth failure: [user=fred] [service=smtp] [realm=] [mech=rimap] [reason=[ALERT] Unexpected response from remote authentication server] This blog post detailed a solution by setting IMAP_MAILBOX_SANITY_CHECK=0 in /etc/courier/imapd. Then restart your courier and saslauthd daemons for config changes to take effect. sudo /etc/init.d/courier-imap restart sudo /etc/init.d/courier-authdaemon restart sudo /etc/init.d/saslauthd restart Watch /var/log/auth.log while trying to send email. Hopefully you're good!

  Read the article

• Configure Postfix to Port other than 25

  - by bwheeler96

  I've done quite a bit of googling on how to reconfigure postfix to work on a different port, but I still can't fond the line(s) people keep talking about in my master.cf. I'm using OS X Mountain Lion, and my ISP blocks traffic both ways on port 25. people have said to look for a line that says smtp inet n - n - - smtpd I can't find it. This is (what I believe to be) unmodified # ==== Begin auto-generated section ======================================== # This section of the master.cf file is auto-generated by the Server Admin # Mail backend plugin whenever mails settings are modified. smtp inet n - n - 1 postscreen smtpd pass - - n - - smtpd dnsblog unix - - n - 0 dnsblog tlsproxy unix - - n - 0 tlsproxy submission inet n - n - - smtpd -o smtpd_tls_security_level=encrypt smtp unix - - n - - smtp # === End auto-generated section =========================================== # Modern SMTP clients communicate securely over port 25 using the STARTTLS command. # Some older clients, such as Outlook 2000 and its predecessors, do not properly # support this command and instead assume a preconfigured secure connection # on port 465. This was sometimes called "smtps", but such usage was never # approved by the IANA and therefore conflicts with another, legitimate assignment. # For more details about managing secure SMTP connections with postfix, please see: # http://www.postfix.org/TLS_README.html # To read more about configuring secure connections with Outlook 2000, please read: # http://support.microsoft.com/default.aspx?scid=kb;en-us;Q307772 # Apple does not support the use of port 465 for this purpose. # After determining that connecting clients do require this behavior, you may choose # to manually enable support for these older clients by uncommenting the following # four lines. #465 inet n - n - - smtpd # -o smtpd_tls_wrappermode=yes # -o smtpd_sasl_auth_enable=yes # -o smtpd_client_restrictions=permit_sasl_authenticated,reject # -o milter_macro_daemon_name=ORIGINATING #628 inet n - n - - smtp pickup fifo n - n 60 1 pickup cleanup unix n - n - 0 cleanup qmgr fifo n - n 300 1 qmgr #qmgr fifo n - n 300 1 oqmgr tlsmgr unix - - n 1000? 1 tlsmgr rewrite unix - - n - - trivial-rewrite bounce unix - - n - 0 bounce defer unix - - n - 0 bounce trace unix - - n - 0 bounce verify unix - - n - 1 verify sacl-cache unix - - n - 1 sacl-cache flush unix n - n 1000? 0 flush proxymap unix - - n - - proxymap proxywrite unix - - n - 1 proxymap # When relaying mail as backup MX, disable fallback_relay to avoid MX loops relay unix - - n - - smtp -o smtp_fallback_relay= # -o smtp_helo_timeout=5 -o smtp_connect_timeout=5 showq unix n - n - - showq error unix - - n - - error retry unix - - n - - error discard unix - - n - - discard local unix - n n - - local virtual unix - n n - - virtual lmtp unix - - n - - lmtp anvil unix - - n - 1 anvil scache unix - - n - 1 scache # # ==================================================================== # Interfaces to non-Postfix software. Be sure to examine the manual # pages of the non-Postfix software to find out what options it wants.

  Read the article

• Linux Debian Security Breach - what now? [closed]

  - by user897075

  Possible Duplicate: My server's been hacked EMERGENCY I installed Debian (Squeeze) a while back in my home network to host some personal sites (thank god). During the installation it prompted me to enter a user other than root - so in a rush I used my name as user and pass (alex/alex for what its worth). I know it's horrible practice but during the setup of this server I'm always logged in as root to perform configurations, etc. Few days or a week passes and I forget to change the password. Then I finally get my web site finished and I open the port forwarding on my router and DynDNS to point to my server in my home. I've done this many times in the past never had issues but I use a cryptic root password and I guess disabled regular accounts. Today I reformat my Windows 7 and after spending all day tweaking and updating SP1 I look for cloning apps and find clonezilla and see it supports SSH cloning, so I go through the process only to discover I need a user, so I log into my web-server and see I have the user 'alex' already in and realize I don't know the password. So I change the password to something cryptic and visit the directory 'home' only to realize their are contents such as passfile, bengos, etc. My heart sinks, I've been hacked!!! Sure as hell there are all sort of scripts and password files. I run a 'last' command and it seems they last logged in april 3rd. Question: What can I do to see if they did anything destructive? Should I reformat and reinstall? How restrictive is Debian/Squeeze in terms of user permissions out of the box - all my personal website stuff was created using 'root' so changing files does not seem to have occured. How did they determine there was a user 'alex' on the machine? Can you query any machine and figure this out? What the users are? Looks like they tried to run a IP scan...other nodes on the network are running Windows 7. One of which seems a little wonky as of late - is it possible they buggered up that system? What corrective action can I take to avoid this from happening again? And figure out what might have changed or been hacked? I'm hoping debian out of box is fairly secure and at best he managed to read some of my source code. :p Regards, Alex

  Read the article

• Recommendations for distributed processing/distributed storage systems

  - by Eddie

  At my organization we have a processing and storage system spread across two dozen linux machines that handles over a petabyte of data. The system right now is very ad-hoc; processing automation and data management is handled by a collection of large perl programs on independent machines. I am looking at distributed processing and storage systems to make it easier to maintain, evenly distribute load and data with replication, and grow in disk space and compute power. The system needs to be able to handle millions of files, varying in size between 50 megabytes to 50 gigabytes. Once created, the files will not be appended to, only replaced completely if need be. The files need to be accessible via HTTP for customer download. Right now, processing is automated by perl scripts (that I have complete control over) which call a series of other programs (that I don't have control over because they are closed source) that essentially transforms one data set into another. No data mining happening here. Here is a quick list of things I am looking for: Reliability: These data must be accessible over HTTP about 99% of the time so I need something that does data replication across the cluster. Scalability: I want to be able to add more processing power and storage easily and rebalance the data on across the cluster. Distributed processing: Easy and automatic job scheduling and load balancing that fits with processing workflow I briefly described above. Data location awareness: Not strictly required but desirable. Since data and processing will be on the same set of nodes I would like the job scheduler to schedule jobs on or close to the node that the data is actually on to cut down on network traffic. Here is what I've looked at so far: Storage Management: GlusterFS: Looks really nice and easy to use but doesn't seem to have a way to figure out what node(s) a file actually resides on to supply as a hint to the job scheduler. GPFS: Seems like the gold standard of clustered filesystems. Meets most of my requirements except, like glusterfs, data location awareness. Ceph: Seems way to immature right now. Distributed processing: Sun Grid Engine: I have a lot of experience with this and it's relatively easy to use (once it is configured properly that is). But Oracle got its icy grip around it and it no longer seems very desirable. Both: Hadoop/HDFS: At first glance it looked like hadoop was perfect for my situation. Distributed storage and job scheduling and it was the only thing I found that would give me the data location awareness that I wanted. But I don't like the namename being a single point of failure. Also, I'm not really sure if the MapReduce paradigm fits the type of processing workflow that I have. It seems like you need to write all your software specifically for MapReduce instead of just using Hadoop as a generic job scheduler. OpenStack: I've done some reading on this but I'm having trouble deciding if it fits well with my problem or not. Does anyone have opinions or recommendations for technologies that would fit my problem well? Any suggestions or advise would be greatly appreciated. Thanks!

  Read the article

• Using Amazon S3 for multiple remote data site uploads, securely

  - by Aitch

  I've been playing about with Amazon S3 a little for the first time and like what I see for various reasons relating to my potential use case. We have multiple (online) remote server boxes harvesting sensor data that is regularly uploaded every hour or so (rsync'ed) to a VPS server. The number of remote server boxes is growing regularly and forecast to keep growing (hundreds). The servers are geographically dispersed. The servers are also automatically built, therefore generic with standard tools and not bespoke per location. The data is many hundreds of files per day. I want to avoid a situation where I need to provision more VPS storage, or additional servers every time we hit the VPS capacity limit, after every N server deployments, whatever N might be. The remote servers can never be considered fully secure due to us not knowing what might happen to them when we are not looking. Our current solution is a bit naive and simply restricts inbound rsync only over ssh to known mac address directories and a known public key. There are plenty of holes to pick in this, I know. Let's say I write or use a script like s3cmd/s3sync to potentially push up the files. Would I need to manage hundreds of access keys and have each server customized to include this (do-able, but key management becomes nightmarish?) Could I restrict inbound connections somehow (eg by mac address), or just allow write-only to any client that was running the script? ( i could deal with a flood of data if someone got into a system? ) having a bucket per remote machine does not seem feasible due to bucket limits? I don't think I want to use a single common key as if one machine is breached then potentially, a malicious hack could get access to the filestore key and start deleting for ll clients, correct? I hope my inexperience has not blinded me to some other solution that might be suggested! I've read lots of examples of people using S3 for backup, but can't really find anything about this sort of data collection, unless my google terminology is wrong... I've written more than I should here, perhaps it can be summarised thus: In a perfect world I just want to have one of our techs install a new remote server into a location and it automagically starts sending files home with little or no intervention, and minimises risk? Pipedream or feasible? TIA, Aitch

  Read the article

• How to install 32-bit libraries using Debian Testing

  - by bgoodr

  Question: What is the way to determine, ahead of time and without doing a full install of 64-bit Debian Testing NETINST, when Debian Testing has 32-bit libraries available and fully working and installable so that the following command works without broken package errors?: apt-get install ia32-libs ia32-libs-gtk The errors that occur when 32-bit libraries are not available, still in some broken state, or whatever is broken are detailed below. I already have concluded that "Just install Stable" is my stop-gap measure for now, but I would like to know the answer to the above question so as to avoid a lengthy installation process only to run into these problems at the very end. Details: I downloaded the 64-bit Debian Testing netinst a couple of days ago. This was "Jessie" built 20131014-06:07 via http://tinyurl.com/lejpa. This is weekly testing build. Yes, I know I should expect problems, and I did. I managed to get it completely installed and was able to invoke into GNOME, but not get past the 32-bit library problem. The problems starts when I attempt to install the 32-bit libraries via: apt-get install ia32-libs ia32-libs-gtk that returns: root@breath:~# apt-get install ia32-libs ia32-libs-gtk Reading package lists... Done Building dependency tree Reading state information... Done Some packages could not be installed. This may mean that you have requested an impossible situation or if you are using the unstable distribution that some required packages have not yet been created or been moved out of Incoming. The following information may help to resolve the situation: The following packages have unmet dependencies: ia32-libs : Depends: ia32-libs-i386 but it is not installable ia32-libs-gtk : Depends: ia32-libs-i386 but it is not installable Depends: ia32-libs-gtk-i386 but it is not installable E: Unable to correct problems, you have held broken packages. I then found an old (2012 is old to me) answer at ia32-libs : Depends: ia32-libs-i386 but it is not installable and even tried what they suggested there which was dpkg --add-architecture i386 apt-get update After executing the above, I tried again but got: root@breath:~# apt-get install ia32-libs ia32-libs-gtk Reading package lists... Done Building dependency tree Reading state information... Done Some packages could not be installed. This may mean that you have requested an impossible situation or if you are using the unstable distribution that some required packages have not yet been created or been moved out of Incoming. The following information may help to resolve the situation: The following packages have unmet dependencies: ia32-libs : Depends: ia32-libs-i386 ia32-libs-gtk : Depends: ia32-libs-i386 E: Unable to correct problems, you have held broken packages. root@breath:~# And then tried this: root@breath:~# dpkg --get-selections | grep hold And that returned nothing. Not only is there broken packages, the system doesn't even know what packages are broken, so Debian Stable is my only solution I know of right now. Hence my question above.

  Read the article

• SSH-forwarded X11 display from Linux to Mac lost after some time

  - by mklein9

  I have a new and vexing problem with ssh forwarding my X11 connection when logging in from a Mac (10.7.2) to Linux (Ubuntu 8.04). I have no trouble using ssh -X to log in to the remote machine and starting an X11-based application from that shell. What has recently started happening is that additional invocations of X11 applications from that same shell, after a while (on the order of hours), are unable to start because the forwarded display is being blocked (I presume). When attempting to start xterm, for example, I get the usual message about a bad DISPLAY setting, such as: xterm Xt error: Can't open display: localhost:10.0 But the X11 application I started right when I logged in is still running along just fine, using that exact same display (localhost:10.0), just that it was started earlier. I turned on verbose logging in sshd_config and I see this in the /var/log/auth.log file in response to the failed xterm startup attempt: sshd[22104]: channel 8: open failed: administratively prohibited: open failed If I ssh -X to the server again, starting a new shell and getting assigned a new display (localhost:11.0), the same process repeats: the X11 applications started early on run just fine for as long as I keep them open (days), but after a few hours I cannot start any new ones from that shell. Particulars: OpenSSH sshd server running on Ubuntu 8.04, display forwarded to a Mac running Lion (10.7.2) with the default Apple X server. The systems are connected on an Ethernet LAN with a single switch between them. Neither machine is running a firewall. Until recently (a few days ago) this setup worked perfectly so I am mystified as to where to look next. I am by no means an X11 or SSH expert but have good UNIX/Linux experience. Nothing obvious has changed in either client or server configuration although I have tried changing a few options to try to debug this, like setting sshd_config's TCPKeepAlive to no, and setting "host +localhost" (you can tell I've been Googling). When logging in from a Linux 11.10 laptop to the same remote host over the same network and switch, this problem does not occur -- an xterm can be invoked successfully hours later from the same ssh login shell while the same experiment from the Mac fails (tested this morning to be sure), so it would appear to be a Mac-specific issue. With "LogLevel DEBUG3" set on the remote machine (sshd server), and no change made in the client connections by me, /var/log/auth.log shows one slight change in connection status reports overnight, which is the port number used by the one successful ssh session from the Linux machine (I think), connection #7 below: sshd[20173]: debug3: channel 7: status: The following connections are open:\r\n #0 server-session (t4 r0 i0/0 o0/0 fd 14/13 cfd -1)\r\n #3 X11 connection from 127.0.0.1 port 57564 (t4 r1 i0/0 o0/0 fd 16/16 cfd -1)\r\n #4 X11 connection from 127.0.0.1 port 57565 (t4 r2 i0/0 o0/0 fd 17/17 cfd -1)\r\n #5 X11 connection from 127.0.0.1 port 57566 (t4 r3 i0/0 o0/0 fd 18/18 cfd -1)\r\n #6 X11 connection from 127.0.0.1 port 57567 (t4 r4 i0/0 o0/0 fd 19/19 cfd -1)\r\n #7 X11 connection from 127.0.0.1 port 59007 In this report, everything is the same between status reports except the port number used by connection #7 which I believe is the Linux client -- the only one still maintaining a display connection. It continues to increment over time, judging by a sequence of these reports overnight. Thanks for any help, -Mike

  Read the article

• ZFS/Btrfs/LVM2-like storage with advanced features on Linux?

  - by Easter Sunshine

  I have 3 identical internal 7200 RPM SATA hard disk drives on a Linux machine. I'm looking for a storage set-up that will give me all of this: Different data sets (filesystems or subtrees) can have different RAID levels so I can choose performance, space overhead, and risk trade-offs differently for different data sets while having a few number of physical disks (very important data can be 3xRAID1, important data can be 3xRAID5, unimportant reproducible data can be 3xRAID0). If each data set has an explicit size or size limit, then the ability to grow and shrink the size limit (offline if need be) Avoid out-of-kernel modules R/W or read-only COW snapshots. If it's a block-level snapshots, the filesystem should be synced and quiesced during a snapshot. Ability to add physical disks and then grow/redistribute RAID1, RAID5, and RAID0 volumes to take advantage of the new spindle and make sure no spindle is hotter than the rest (e.g., in NetApp, growing a RAID-DP raid group by a few disks will not balance the I/O across them without an explicit redistribution) Not required but nice-to-haves: Transparent compression, per-file or subtree. Even better if, like NetApps, analyzes the data first for compressibility and only compresses compressible data Deduplication that doesn't have huge performance penalties or require obscene amounts of memory (NetApp does scheduled deduplication on weekends, which is good) Resistance to silent data corruption like ZFS (this is not required because I have never seen ZFS report any data corruption on these specific disks) Storage tiering, either automatic (based on caching rules) or user-defined rules (yes, I have all-identical disks now but this will let me add a read/write SSD cache in the future). If it's user-defined rules, these rules should have the ability to promote to SSD on a file level and not a block level. Space-efficient packing of small files I tried ZFS on Linux but the limitations were: Upgrading is additional work because the package is in an external repository and is tied to specific kernel versions; it is not integrated with the package manager Write IOPS does not scale with number of devices in a raidz vdev. Cannot add disks to raidz vdevs Cannot have select data on RAID0 to reduce overhead and improve performance without additional physical disks or giving ZFS a single partition of the disks ext4 on LVM2 looks like an option except I can't tell whether I can shrink, extend, and redistribute onto new spindles RAID-type logical volumes (of course, I can experiment with LVM on a bunch of files). As far as I can tell, it doesn't have any of the nice-to-haves so I was wondering if there is something better out there. I did look at LVM dangers and caveats but then again, no system is perfect.

  Read the article

• Messages stuck in SMTP queue - Exchange 2003

  - by Diav

  I need your help people ;-) I have a problem with messages coming into our Exchange Server and ones going out through it. Basically, the messages are stuck in the SMTP queue. A message will come into the server, I can see it listed under "Exchange System Manager", but if you list the properties of the message queue it says something like 00:10 SMTP Message queued for local delivery 00:10 SMTP Message delivered locally to [email protected] 00:10 SMTP Message scheduled to retry local delivery 00:11 SMTP Message delivered locally to [email protected] 00:11 SMTP Message scheduled to retry local delivery etc etc For outgoing message list looks like this: 10:55 SMTP: Message Submitted to Advanced Queuing 10:55 SMTP: Started Message Submission to Advanced Queue 10:55 SMTP: Message Submitted to Categorizer 10:55 SMTP: Message Categorized and Queued for Routing 10:55 SMTP: Message Routed nad Queued for Remote Delivery And the end - since then status didn't change, message is in queue, I am forcing connection from time to time but without an effect. I checked connection with smarthost (used telnet for that) and everything seems to work correctly, so the problem is probably on exchange side. I am using Exchange Server 2003 running on Small Business Server 2003. I don't have any antivirus installed on server. Remaining free space on each partition is over 3Gb, on partition with data bases - it is over 12Gb. All was working good and without problems since 2005, problems started in half of this june - messages started going out and being stuck almost randomly (I don't see a pattern yet, some are going out, some are not, some are going after several hours). I don't know what to do, what to check more, so please, any ideas? Best regards, D. edit Priv1.edb has 14,5GB and priv1.stm 2,6GB - together those files have more than 16GB - can it be the reason? If yes, then what? Indeed, I haven't thought that it can have something in common with my problem, but several users reported recent problems with Outlook Web Access - they can log in, they see the list of their mails, but they can't see the content of their emails. Although when they are connecting with Outlook 2003/2007 - there is no such problem, only with OWA there is. edit2 So,.. It works now, and I have to admit that I am not really sure what the problem was (hope it won't come back). What have I done: Cleaned up some mailboxes to reduce size of them Dismounted Information Store Defragmentated data base files ( I used eseutil: c:\program files\exchsrvr\bin eseutil /d g:\data base\Exchsrvr\MDBDATA\priv1.edb ) Mounted Information Store back ..and before I managed to do anything else - my queue started moving, elements which were kept there already for days - started moving and after few minutes everything was sent, both, outside and locally. But: priv1.edb is still big (13 884 203 008), priv1.stm as well (2 447 384 576), so this is probably not the issue of size of the file. And if not this, so what was that? And if that was issue of size of the file, then soon it will repeat - is there something I can do to avoid it ?

  Read the article

• Nginx $scheme doesn't always work while using SSL for one specific page

  - by jjiceman

  I read and followed this question in order to configure nginx to force SSL for one page (admin.php for XenForo), and it is working well for a few of the site administrators but is not for myself. I was wondering if anyone has any advice on how to improve this configuration: ... ssl_certificate example.net.crt; ssl_certificate_key example.key; server { listen 80 default; listen 443 ssl; server_name www.example.net example.net; access_log /srv/www/example.net/logs/access.log; error_log /srv/www/example.net/logs/error.log; root /srv/www/example.net/public_html; index index.php index.html; location / { if ( $scheme = https ){ rewrite ^ http://example.net$request_uri? permanent; } try_files $uri $uri/ /index.php?$uri&$args; index index.php index.html; } location ^~ /admin.php { if ( $scheme = http ) { rewrite ^ https://example.net$request_uri? permanent; } try_files $uri /index.php; include fastcgi_params; fastcgi_pass 127.0.0.1:9000; fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; fastcgi_param HTTPS on; } location ~ \.php$ { try_files $uri /index.php; include fastcgi_params; fastcgi_pass 127.0.0.1:9000; fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; fastcgi_param HTTPS off; } } ... It seems that the extra information in the location ^~ /admin.php block is unecessary, does anyone know of an easy way to avoid duplicate code? Without it it skips the php block and just returns the php files. Currently it applies https correctly in Firefox when I navigate to admin.php. In Chrome, it downloads the admin.php page. When returning to the non-https website in Firefox, it does not correctly return to http but stays as SSL. Like I said earlier, this only happens for me, the other admins can go back and forth without a problem. Is this an issue on my end that I can fix? And does anyone know of any ways I could reduce duplicate configuration options in the configuration? Thanks in advance!

  Read the article

• Automatically starting svnserve on Snow Leopard

  - by Cleggy

  Note: I originally asked this question on Server Fault (http://serverfault.com/questions/148052/automatically-starting-svnserve-on-snow-leopard), but I thought this may be a more appropriate place to ask. I have installed Subversion onto my iMac running Snow Leopard, but am having trouble getting svnserve to start up automatically. As I understand it (I'm still fairly green with OSX), the best way to do that is to utilize launchd. To that end, I have created the following .plist file in the /Library/LaunchDaemons folder. If I use launchctl to execute this file, svnserve starts as expected, but it doesn't automatically start when the system starts up or I log in. <?xml version="1.0" encoding="UTF-8"?> <!DOCTYPE plist PUBLIC "-//Apple//DTD PLIST 1.0//EN" "http://www.apple.com/DTDs/PropertyList-1.0.dtd"> <plist version="1.0"> <dict> <key>Disabled</key> <false/> <key>Label</key> <string>org.tigris.subversion.svnserve</string> <key>UserName</key> <string>Dave</string> <key>ProgramArguments</key> <array> <string>/opt/subversion/bin/svnserve</string> <string>--inetd</string> <string>--root=/Users/Shared/SVNrep</string> </array> <key>ServiceDescription</key> <string>Subversion Standalone Server</string> <key>Sockets</key> <dict> <key>Listeners</key> <array> <dict> <key>SockFamily</key> <string>IPv4</string> <key>SockServiceName</key> <string>svn</string> <key>SockType</key> <string>stream</string> </dict> <dict> <key>SockFamily</key> <string>IPv6</string> <key>SockServiceName</key> <string>svn</string> <key>SockType</key> <string>stream</string> </dict> </array> </dict> <key>inetdCompatibility</key> <dict> <key>Wait</key> <false/> </dict> </dict> </plist> I have tried many different configs in the .plist, including auto-starting, simplifying the listeners section, removing dependence on inetd, but they all show the same symptom. The files work when started using launchctl load, but do not automatically start up svnserve if the iMac is rebooted. If anyone here could provide any suggestions as to how to get this to work, I'd really appreciate it.

  Read the article

• IIS URL Rewrite - Redirect any HTTPS traffic to sub-domain

  - by uniquelau

  We have an interesting hosting environment that dictates all secure traffic must travel over a specific sub domain. E.g. http://secure.domain.com/my-page I'd like to handle this switch using URL Rewrite, i.e. at server level, rather than application level. My cases are: https://secure.domain.com/page = NO CHANGE, remains the same https://domain.com/page = sub-domain inserted, https://secure.domain.com/page https://www.domain.com/page = remove 'www', insert sub-domain In my mind the logic is: INPUT = Full Url = http://www.domain.com/page If INPUT contains HTTPS Then check Full URL, does it contain 'secure'? If YES do nothing, if no add 'secure' If INPUT contains 'www' remove 'www' The certificate is not a wild card (e.g. top level domain) and is issues to: https://secure.domain.com/ The website could also be hosted in a staging environment. E.g. https://secure.environment.domain.com/ I do not have control over 'environment' or 'domain' or the 'tld'. Laurence - Update 1, 19th August So as mentioned below, the trick here is to avoid a redirect loop that could drive anyone well loopy. This is what I propose: One rule to force certain traffic to the secure domain: <rule name="Force 'Umbraco' to secure" stopProcessing="true"> <conditions logicalGrouping="MatchAll"> <add input="{REQUEST_URI}" pattern="^/umbraco/(.+)$" ignoreCase="true" /> <add input="{HTTP_HOST}" negate="true" pattern="^secure\.(.+)$" /> </conditions> <action type="Redirect" url="https://secure.{HTTP_HOST}/{R:0}" redirectType="Permanent" /> </rule> Another rule, that then removes the secure domain, expect for traffic on the secure domain. <rule name="Remove secure, expect for Umbraco" stopProcessing="true"> <match url="(.*)" ignoreCase="true" /> <conditions logicalGrouping="MatchAll"> <add input="{HTTP_HOST}" pattern="^secure\.(.+)$" /> <add input="{REQUEST_URI}" negate="true" pattern="^/umbraco/(.+)$" ignoreCase="true" /> </conditions> <!-- Set Domain to match environment --> <action type="Redirect" url="http://staging.domain.com/{R:0}" appendQueryString="true" redirectType="Permanent" /> </rule> This works for a single directory or group of files, however I've been unable to add additional logic into those two rules. For example you might have 3 folders that need to be secure, I tried adding these as Negate records, but then no redirection happens at all. Hmmm! L

  Read the article

• Multiple Homed Windows 2008 Server / Windows 7 Client

  - by Daniel Scott

  I have a small Windows 2008 network, with some Windows 7 clients. The clients are both laptops with docking stations and I would like them to communicate with the Windows 2008 server (for filesharing) through the wired network whilst they're docked. Internet connectivity for all machines (clients and server) is via a Wireless LAN, so the wireless adapter in the Windows 7 clients stays active while they're docked. When the laptops are un-docked, it would be nice to still be able to contact the windows 2008 server for print sharing (and slower file sharing) - hence the server also being on the wireless LAN. The windows 2008 server is running Active Directory, DHCP and DNS. It controls DHCP leases on the wired network and holds the DNS records for "myserver.mycompany.local", which is what the filesharing clients connect to. Ideally I'd like the DNS records to return the wired IP first so that this is the address that the laptops will attempt initially - but there doesn't seem to be a way to do that? At present the server's IP on the wireless LAN comes out of an nslookup above the wired Lan IP. The multi-homing works perfectly - but in the wrong order! Switch on the wireless lan and ping myserver and it goes to the wireless IP. Disable the wireless on the client and do the same ping again and after a couple of seconds it starts pinging the wired address. Does anyone have any suggestions on how to make this work in a predictable order? - or even if it can work. Alternative 1? If it can't work, then would this work: Remove the wireless adapter from the server, put a wireless router/bridge on the wired network (set up to route to/from the wireless LAN's subnet), then configure the clients with two routes to the (now) single IP of the server with metrics favouring direct communication over the wired LAN first? Alternative 2? Should I instead single-home the laptops so all of their connectivity is via the wired-LAN while they're docked? (and route via the windows 2008 server - or a dedicated wireless bridge/router)? My concern here is that I'd like undocking to be seamless - and if the clients are in the middle of downloading something from the internet I wouldn't want whatever they're doing interupted as they switch IP addresses onto the Wireless network. Perhaps this isn't the case and I'm concerned over nothing? Any thoughts? :) UPDATE I seem to have cracked it (at least DNS entries come out in the order I hope for - and pinging the server with various combinations of wired, wireless and both interfaces enabled uses the IP I want) ... I set the binding order of the NICs on the Server (which is acting as Domain Controller, DHCP and DNS server) so that the Wired NIC is before the Wireless adapter. (Start -- type "Network Interfaces" -- Select "View Network Connections" -- Press Alt to show classic dropdown menus -- Advanced -- Advanced Settings) Now, an nslookup (from the client) of the server's hostname returns the Wired IP first, followed by the Wireless IP. The wired IP now seems to be used whenever it's contactable. Incidentally, the metrics on the wired and wireless routes (on the client) also favour the wired LAN (based on Windows' automatically assigned metrics) - but this was always the case, even when I was having trouble getting the wired IP to be "favoured". I'm not entirely sure if this is coincidence - or if a DNS server running on Windows, handing back IP addresses for itself does actually take the binding order of it's own network interfaces into account? It would be interesting to hear from someone who can confirm or deny that (or confirm that the binding order on the server plays a role for some other reason?)

  Read the article

• how does openvpn decide which interface to get IP addrs from

  - by bkrupa

  Using ubuntu 10.04 on both ends. We have a client and server machine on the SAME network attempting to make a vpn connection. We use the config files from here and made minimal changes. The server and client start and seem to connect without any trouble. The server looks like: Wed Feb 23 22:13:22 2011 MULTI: multi_create_instance called Wed Feb 23 22:13:22 2011 192.168.1.55:47166 Re-using SSL/TLS context Wed Feb 23 22:13:22 2011 192.168.1.55:47166 LZO compression initialized Wed Feb 23 22:13:22 2011 192.168.1.55:47166 Control Channel MTU parms [ L:1574 D:138 EF:38 EB:0 ET:0 EL:0 ] Wed Feb 23 22:13:22 2011 192.168.1.55:47166 Data Channel MTU parms [ L:1574 D:1450 EF:42 EB:135 ET:32 EL:0 AF:3/1 ] Wed Feb 23 22:13:22 2011 192.168.1.55:47166 Local Options hash (VER=V4): 'f7df56b8' Wed Feb 23 22:13:22 2011 192.168.1.55:47166 Expected Remote Options hash (VER=V4): 'd79ca330' Wed Feb 23 22:13:22 2011 192.168.1.55:47166 TLS: Initial packet from 192.168.1.55:47166, sid=69112e42 5458135b *...* Wed Feb 23 22:13:22 2011 192.168.1.55:47166 Control Channel: TLSv1, cipher TLSv1/SSLv3 DHE-RSA-AES256-SHA, 1024 bit RSA Wed Feb 23 22:13:22 2011 192.168.1.55:47166 [client1] Peer Connection Initiated with 192.168.1.55:47166 On the client side the connection looks like: Wed Feb 23 22:20:07 2011 [server] Peer Connection Initiated with [AF_INET]192.168.1.41:1194 Wed Feb 23 22:20:10 2011 SENT CONTROL [server]: 'PUSH_REQUEST' (status=1) Wed Feb 23 22:20:10 2011 PUSH: Received control message: 'PUSH_REPLY,route-gateway 10.8.0.4,ping 10,ping-restart 120,ifconfig 10.8.0.50 255.255.255.0' ... Wed Feb 23 22:20:10 2011 /sbin/ifconfig tap0 10.8.0.50 netmask 255.255.255.0 mtu 1500 broadcast 10.8.0.255 Wed Feb 23 22:20:10 2011 Initialization Sequence Completed The openvpn server has been configured to assign ip addresses in the range 10.8.0.* and the client has been given 10.8.0.50. When I run the following nmap from the client: Starting Nmap 5.00 ( http://nmap.org ) at 2011-02-23 22:04 EST Host 10.8.0.50 is up (0.00047s latency). Nmap done: 256 IP addresses (1 host up) scanned in 30.34 seconds Host 192.168.1.1 is up (0.0025s latency). Host 192.168.1.18 is up (0.074s latency). Host 192.168.1.41 is up (0.0024s latency). Host 192.168.1.55 is up (0.00018s latency). Nmap done: 256 IP addresses (4 hosts up) scanned in 6.33 seconds If I run an nmap from the server on 10.8.0.* I get nothing. If the client has two interfaces (wireless and tap device) when you look for a certain ip address, how does it decide which interface to connect on? edit I am trying to set up a vpn so that I can connect to my home network from a remote network. It seems like openvpn is connecting but none of the computers on my home network appear as network machines even after the connection is "Established". Stripped versions of the client and server config files are posted below. Thanks for any help you can offer. server.conf port 1194 proto udp dev tap ca /etc/openvpn/easy-rsa/keys/ca.crt cert /etc/openvpn/easy-rsa/keys/server.crt key /etc/openvpn/easy-rsa/keys/server.key # This file should be kept secret dh /etc/openvpn/easy-rsa/keys/dh1024.pem ifconfig-pool-persist ipp.txt server-bridge 10.8.0.4 255.255.255.0 10.8.0.50 10.8.0.100 keepalive 10 120 comp-lzo persist-key persist-tun status openvpn-status.log verb 3 client.conf client dev tap dev-node tap0901 proto udp remote ********** 1194 resolv-retry infinite nobind persist-key persist-tun ca ca.crt cert client1.crt key client1.key comp-lzo verb 3 one other thing that might be helpful, I tried to connect using the openvpn gui for windows and the connection stalls out on "obtaining configuration" and the bar just scrolls forever.

  Read the article

• Postfix certificate verification failed for smtp.gmail.com

  - by Andi Unpam

  I have problem, my email server using postfix with gmail smtp, i use account google apps, but always ask for SASL authentication failed, I sent an email using php script, after I see the error logs in the wrong password, after I open the URL from the browser and no verification postfixnya captcha and could return, but after 2-3 days later happen like that again. This my config postfix #myorigin = /etc/mailname smtpd_banner = Hostingbitnet Mail Server biff = no append_dot_mydomain = no readme_directory = no myhostname = webmaster.hostingbitnet.com alias_maps = hash:/etc/aliases alias_database = hash:/etc/aliases myorigin = /etc/mailname mydestination = localhost, webmaster.hostingbitnet.com, localhost.localdomain, 103.9.126.163 relayhost = [smtp.googlemail.com]:587 relay_transport = relay relay_destination_concurrency_limit = 1 mynetworks = 127.0.0.0/8, 192.168.0.0/16, 172.16.0.0/16, 10.0.0.0/8, 103.9.126.0/24 mailbox_size_limit = 0 recipient_delimiter = + inet_interfaces = all default_transport = smtp relayhost = [smtp.gmail.com]:587 smtp_sasl_auth_enable = yes smtp_sasl_password_maps = hash:/etc/postfix/google-apps smtp_sasl_security_options = noanonymous smtp_use_tls = yes smtp_sender_dependent_authentication = yes tls_random_source = dev:/dev/urandom default_destination_concurrency_limit = 1 smtp_tls_CAfile = /etc/postfix/tls/root.crt smtp_tls_cert_file = /etc/postfix/tls/cert.pem smtp_tls_key_file = /etc/postfix/tls/privatekey.pem smtp_tls_session_cache_database = btree:$data_directory/smtp_tls_session_cache smtp_tls_security_level = may smtp_tls_loglevel = 1 smtpd_tls_CAfile = /etc/postfix/tls/root.crt smtpd_tls_cert_file = /etc/postfix/tls/cert.pem smtpd_tls_key_file = /etc/postfix/tls/privatekey.pem smtpd_tls_session_cache_database = btree:$data_directory/smtpd_tls_session_cache smtpd_tls_security_level = may smtpd_tls_loglevel = 1 #secure smtpd_recipient_restrictions = permit_mynetworks,permit_sasl_authenticated,check_client_access hash:/var/lib/pop-before-smtp/hosts,reject_unauth_destination Log from mail.log Oct 30 14:51:13 webmaster postfix/smtp[9506]: Untrusted TLS connection established to smtp.gmail.com[74.125.25.109]:587: TLSv1 with cipher RC4-SHA (128/128 bits) Oct 30 14:51:15 webmaster postfix/smtp[9506]: 87E2739400B1: SASL authentication failed; server smtp.gmail.com[74.125.25.109] said: 535-5.7.1 Please log in with your web browser and then try again. Learn more at?535 5.7.1 https://support.google.com/mail/bin/answer.py?answer=78754 ix9sm156630pbc.7 Oct 30 14:51:15 webmaster postfix/smtp[9506]: setting up TLS connection to smtp.gmail.com[74.125.25.108]:587 Oct 30 14:51:15 webmaster postfix/smtp[9506]: certificate verification failed for smtp.gmail.com[74.125.25.108]:587: untrusted issuer /C=US/O=Equifax/OU=Equifax Secure Certificate Authority Oct 30 14:51:16 webmaster postfix/smtp[9506]: Untrusted TLS connection established to smtp.gmail.com[74.125.25.108]:587: TLSv1 with cipher RC4-SHA (128/128 bits) Oct 30 14:51:17 webmaster postfix/smtp[9506]: 87E2739400B1: to=<[email protected]>, relay=smtp.gmail.com[74.125.25.108]:587, delay=972, delays=967/0.03/5.5/0, dsn=4.7.1, status=deferred (SASL authentication failed; server smtp.gmail.com[74.125.25.108] said: 535-5.7.1 Please log in with your web browser and then try again. Learn more at?535 5.7.1 https://support.google.com/mail/bin/answer.py?answer=78754 s1sm3850paz.0) Oct 30 14:51:17 webmaster postfix/error[9508]: B3960394009D: to=<[email protected]>, orig_to=<root>, relay=none, delay=29992, delays=29986/5.6/0/0.07, dsn=4.7.1, status=deferred (delivery temporarily suspended: SASL authentication failed; server smtp.gmail.com[74.125.25.108] said: 535-5.7.1 Please log in with your web browser and then try again. Learn more at?535 5.7.1 https://support.google.com/mail/bin/answer.py?answer=78754 s1sm3850paz.0) BTW I made cert follow the link here http://koti.kapsi.fi/ptk/postfix/postfix-tls-cacert.shtml and it worked, but after 2/3 days my email back to problem invalid SASL, and then i'm required to log in use a browser and enter the captcha there but success log in after input captcha, and my email server can send emails from telnet or php script. but it will be back in trouble after 2/3days later. My question is how to make it permanent certificate? Thanks n greeting.

  Read the article

• Cannot browse network shares in Windows Explorer, but paths are still accessible

  - by Jeff Lockhart

  Windows Explorer has somehow corrupted itself and I'm not sure how to fix this problem. My Windows installation has been in use for a few years with network shares setup and working. Recently, I noticed that a program that I use to save network share paths to a database was no longer opening the explorer window to browse the path. It usually opens to the last path saved, but now it was just not opening at all. When I go to Windows Explorer to browse the network share directly, I get the error \\SERVER is not accessible. You might not have permission to use this network resource. Contact the administrator of this server to find out if you have access permissions. The specified network provider name is invalid. The network shares are just shares on the server itself (once saved to the database, they're used on the server as well as clients to reach files). The strange thing is, the files are still accessible from the program that uses them if I type the network share path in manually. So it is only a problem with Windows Explorer browsing the path. The reason I think there is some sort of configuration or setting, possibly in the registry, corrupted is that when the problem first manifest itself, I was somehow able to open an explorer window to a network share path, but the breadcrumb in the address bar did not function properly. It duplicated the share name folder at the top of the breadcrumb stack and when I clicked the second of the duplicated share folder, it crashed explorer.exe. I haven't been able to browse any network share path since this happened. I have tried using the IP address directly \\192.168.1.# as well as \\localhost and neither of those work either. I have tried running sfc /scannow and it did not find any errors. I tried ipconfig /flushdns and this made no difference. Attempting to map the network share to a drive fails using either the explorer GUI or net use command. Is there some way to reset Windows Explorer somehow to resolve this? I'd really like to avoid reinstalling Windows entirely if I can.

  Read the article

• bind9 DNS Ubuntu names pingible on server, but not on Windows Machines?

  - by leeand00

  I setup a DNS server today on Ubuntu, following this tutorial. My intent was to setup my network for dns-name resolving on the private LAN within a single zone (nothing fancy I just want name resolution). I've tested the setup on the DNS server machine itself, and I can ping all the machines listed in the configuration file. I've also configured the Windows Machines on my network, and for some reason they are incapable of pinging by names as was possible on the DNS Server itself. I've tried running nslookup on the Windows DNS clients and I receive and error mentioning the address of the DNS server. DNS forwarding works fine, I'm not having any trouble accessing the internet, the problem only lies within accessing names within the private LAN. Here are my configuration files: options { directory "/var/cache/bind"; // If there is a firewall between you and nameservers you want // to talk to, you may need to fix the firewall to allow multiple // ports to talk. See http://www.kb.cert.org/vuls/id/800113 // If your ISP provided one or more IP addresses for stable // nameservers, you probably want to use them as forwarders. // Uncomment the following block, and insert the addresses replacing // the all-0's placeholder. // forwarders { // 0.0.0.0; // }; forwarders { 8.8.8.8; 8.8.8.4; 74.242.0.12; //68.87.76.178; }; auth-nxdomain no; # conform to RFC1035 listen-on-v6 { any; }; }; /etc/bind/named.conf.options zone "leerdomain.local" { type master; file "/etc/bind/zones/leerdomain.local.db"; notify no; }; zone "2.168.192.in-addr.arpa" { type master; file "/etc/bind/zones/rev.2.168.192.in-addr.arpa"; notify no; }; /etc/bind/named.conf.local Lookup: $TTL 3D @ IN SOA ns.leerdomain.local. admin.leerdomain.local. ( 2010011001 28800 3600 604800 38400 ); leerdomain.local. IN NS ns.leerdomain.local. ns IN A 192.168.2.9 asus IN A 192.168.2.254 www IN CNAME asus vaio IN A 192.168.2.253 iptouch IN A 192.168.2.252 toshiba IN A 192.168.2.251 gw IN A 192.168.2.1 TXT "Network Gateway" /etc/bind/zones/leerdomain.local.db (Validates fine with named-checkzone when validating zone leerdomain.local) Reverse Lookup: $TTL 3D @ IN SOA ns.leerdomain.local. admin.leerdomain.local. ( 201001101 28800 604800 604800 86400 ) IN NS ns.leerdomain.local. 1 IN PTR gw.leerdomain.local. 254 IN PTR asus.leerdomain.local. 253 IN PTR vaio.leerdomain.local. 252 IN PTR iptouch.leerdomain.local. 251 IN PTR toshiba.leerdomain.local. /etc/bind/zones/rev.2.168.192.in-addr.arpa *(Does not validate with named-checkzone when validating zone leerdomain.local gives an error of: zone leerdomain.local/IN: NS 'ns.leerdomain.local' has no address records (A or AAAA) zone leerdomain.local/IN: not loaded due to errors. * Despite not validating bind9 starts without errors in /var/log/syslog I've also configured a few of the windows machines on my network to have the static ip as specified in the lookup and reverse lookup config files. i.e. Using nslookup yields the following results: C:\Users\leeand00>nslookup ns Server: UnKnown Address: 192.168.2.9 *** UnKnown can't find ns: Non-existent domain C:\Users\leeand00>nslookup gw Server: UnKnown Address: 192.168.2.9 Name: gw. Additionally trying to ping by name also fails on machines that are not the DNS Server. Is there something wrong with my configuration of either the nameserver or the Windows Boxes that is keeping me from accessing other machines using names?

  Read the article

• nginx - 403 Forbidden

  - by michell90

  I've trouble to get aliases working correctly on nginx. When i try to access the aliases, /pma and /mba (see secure.example.com.conf), i get a 403 Forbidden but the base url works correctly. I read a lot of posts but nothing helped, so here i am. Nginx and php-fpm are running as www-data:www-data and the permissions for the directories are set to: drwxrwsr-x+ 5 www-data www-data 4.0K Dec 5 22:48 ./ drwxr-xr-x. 3 root root 4.0K Dec 4 22:50 ../ drwxrwsr-x+ 2 www-data www-data 4.0K Dec 5 13:10 mda.example.com/ drwxrwsr-x+ 11 www-data www-data 4.0K Dec 5 10:34 pma.example.com/ drwxrwsr-x+ 3 www-data www-data 4.0K Dec 5 11:49 www.example.com/ lrwxrwxrwx. 1 www-data www-data 18 Dec 5 09:56 secure.example.com -> www.example.com/ Im sorry for the bulk, but i thought better too much than too little. Here are the configuration files: /etc/nginx/nginx.conf user www-data www-data; worker_processes 1; error_log /var/log/nginx/error.log; #error_log /var/log/nginx/error.log notice; #error_log /var/log/nginx/error.log info; pid /var/run/nginx.pid; events { worker_connections 1024; } http { include /etc/nginx/mime.types; default_type application/octet-stream; log_format main '$remote_addr - $remote_user [$time_local] "$request" ' '$status $body_bytes_sent "$http_referer" ' '"$http_user_agent" "$http_x_forwarded_for"'; access_log /var/log/nginx/access.log main; sendfile on; keepalive_timeout 65; include /etc/nginx/sites-enabled/*; } /etc/nginx/sites-enabled/secure.example.com server { listen 80; server_name secure.example.com; return 301 https://$host$request_uri; } server { listen 443; server_name secure.example.com; access_log /var/log/nginx/secure.example.com.access.log; error_log /var/log/nginx/secure.example.com.error.log; root /srv/http/secure.example.com; include /etc/nginx/ssl/secure.example.com.conf; include /etc/nginx/conf.d/index.conf; include /etc/nginx/conf.d/php-ssl.conf; autoindex off; location /pma/ { alias /srv/http/pma.example.com; } location /mda/ { alias /srv/http/mda.example.com; } } /etc/nginx/ssl/secure.example.com.conf ssl on; ssl_certificate /etc/nginx/ssl/secure.example.com.crt; ssl_certificate_key /etc/nginx/ssl/secure.example.com.key; ssl_protocols SSLv3 TLSv1 TLSv1.1 TLSv1.2; ssl_ciphers HIGH:!aNULL:!MD5; /etc/nginx/conf.d/index.conf index index.php index.html index.htm; /etc/nginx/conf.d/php-ssl.conf location ~ \.php$ { try_files $uri =404; fastcgi_pass unix:/var/run/php-fpm/php-fpm.sock; fastcgi_index index.php; fastcgi_param HTTPS on; fastcgi_param SCRIPT_FILENAME $request_filename; include fastcgi_params; } /var/log/nginx/secure.example.com.error.log 2013/12/05 22:49:04 [error] 29291#0: *2 directory index of "/srv/http/pma.example.com" is forbidden, client: 176.199.78.88, server: secure.example.com, request: "GET /pma/ HTTP/1.1", host: "secure.example.com" EDIT: forgot to mention, i'm running CentOS 6.4 x86_64 and nginx 1.0.15 Thanks in advance!

  Read the article

< Previous Page | 474 475 476 477 478 479 480 481 482 483 484 485  | Next Page >