Search Results

Search found 3587 results on 144 pages for 'vmware vcloud director'.

Page 50/144 | < Previous Page | 46 47 48 49 50 51 52 53 54 55 56 57  | Next Page >

• spurious hardware memory 'errors' on hp dl380 g5's being generated

  - by friedchicken

  Hi All, i've got 2 new HP dl380g5 servers running HP's esxi4 patched to 219382. they have both been patched up to the latest hp firmware levels (firmware cd 8.7) both are running 32gb (4 x 8gb sticks) both servers are showing the same symptoms - the memory lights come on for two (random) dimms on the front of the server and the health led turns red. sometimes the server stays up and running with no problems. othertimes the server locks dead and only a power reset can bring it back. there is nothing showing in the ilo logs and nothing within the vmware hardware monitoring. the memory has been replaced i've got other customers that have been running dl380g5's with out any issues on esx3.5 - this is our first vsphere deployment with them. these are meant to go live soon so any advice would be great. thanks in advance.

  Read the article

• Set Valid IP On Vmware Vm's Help Please

  - by Shahin At

  I Have a VPS.And i on my vps installed vmware workstation version 9.now i have 3 valid ip's: XXX.152.193.66 XXX.152.193.101 XXX.152.193.103 Gateway: XXX.152.193.65 now tow ip's set in host and i want to 1 ip set on vm. network vm is bridge and set ip on vm but this ip from out of internal network not ping and in vm not ping to gateway. What can I do to solve this problem? my ip is unassigned and only set on vm and use bridge network mode.and gw,mask,dns is set.but not ping. i set this ip on host and without problems is worked, But I do not know why on vm not worked. my host OS Is Windows Server 2003 and firewall is off and RRAs(routing and remote access) For VPN service is Enable. Do not host or virtual machines to create a IP route?

  Read the article

• ESXi standalone host cannot power on any virtual machines

  - by Mark Henderson

  I have a standalone VMWare ESXi host on ESXi 5.1. It currently has a handful of VMs powered on, and they are running fine. If I try to power on any other VM - any VM at all - I am receiving the following message: Power On virtual machine:A general system error occurred: The virtual machine could not start I have been through everything on KB2001005 and KB1006232 and their steps are either not applicable, or don't change anything. Nothing is generated in the virtual machine's log file. Where can I troubleshoot from here?

  Read the article

• Is paravirtualization evil?

  - by Daniel

  I have an VMWare ESX Server v3.5 with a few virtualized Debian Lenny VMs (kernel 2.6.22 with vmi) running Apache Tomcat 5.5. I enabled paravirtualization, and Disk IO increased from about 240MB/s to 380MB/s, making me a happy admin. The problem now is that my apache tomcat becomes deadlocked during startup, running with 200% CPU (I have 2 CPUS assigned to the VM), and don't know how to get both: A stable system and a fast system. I somewhere heared that paravirtualization is legacy anyway and won't be available on newer ESX servers. Is there a replacement for this seemingly performance-improving option, or is it discontinued becauses it is just unstable? What is the state of paravirtualization? Should I ignore it completely? Thanks for all answers in advance.

  Read the article

• Under what circumstances might an IIS6 website be automatically deleted?

  - by E. Anderson

  Late last week my colleagues did some hardware maintenance on one of our vmWare esxi servers. One of the guests is a Windows Server 2003 Web Edition system that runs our low-traffic web sites. We discovered this morning that one of those websites was no longer working with what appeared to be an SSL error. After logging in, I found that the web site in question had been deleted from IIS! Is it possible for this to happen without a user actually going in and deleting that single web site? All of the other sites were fine. The files for the site in question had not been touched. I just re-created the web site, assigned the SSL cert, and everything was working again. When I logged in, I did see the 'Unexpected Shutdown' dialog.

  Read the article

• SQL Server 2005 64bit on 16GB machine uses 3.6GB memory only

  - by ArjanP

  Maximum server memory is set to the maxvalue AWE is disabled (should not be needed in 64 bit anyway) Windows Server 2008 Enterprise SP2 It is a virtual server using VMWare If I look in Task Manager the sqlservr.exe process only uses about 3.6 GB of memory. Is that number not real? Shouldn't it attempt to use all available memory? If I run DBCC MEMORYSTATUS I get: VM Reserved 16670136 VM Committed 3640664 It looks like a memory limit I shouldn't be seeing in a 64 bit environment.. how can I get SQL2005 to use more memory?

  Read the article

• how to clone a physical "individual partition" vmdk into a "local" (file-based) vmdk?

  - by BJH

  Hello. I have a physical disk with a small (60GB) partition containing my guest OS. The physical disk also contains a large (240GB) block of unpartitioned space. My vmdk is defined as a physical "individual partition". I want to convert the source physical "individual partition" vmdk into a local (file-based) vmdk. The command - vmware-vdiskmanager -r sourcevmdk targetvmdk -t 2 creates a 300GB vmdk that includes both the desired 60GB "individual partition" and the 240GB of useless unpartitioned space ! How can I create a local vmdk with just the individual partition?

  Read the article

• Host CPID, Geast CPUID and UserCPUID / what are they?

  - by amir.csco

  i found out that there are some IDs associated to the CPUIDs in vmx file of each virtual machine, these IDs are; hostCPUID.{Num} hostCPUID.80000001 guestCPUID.{Num} guestCPUID.80000001 userCPUID.{Num} userCPUID.80000001 i had some examination and search and i found out that guestCPUID and userCPUID are the same but hostCPUID always is different, Also i realized that these IDs are 32 hexadecimal characters that contains EDX, EAX, ECX and EDX i just want to know why hostCPUID is different from two other IDs?? and what is the different between these format of IDs and another format that explain in VMware documents ( cpuid.{Num}.edx or cpuid.{Num}.eax ) that written in binary codes not hexadecimal?? also i need to know why there are no CPUIDs in vmx file of some virtual appliance that often are available in OVF/OVA format and we can just deploy it?? Best Regards,

  Read the article

• Is an I/O benchmark made for hardware an accurate assessment of a Windows VM's performance under vSphere 5?

  - by Jeremy

  We support an enterprise application running on Windows Server 2008 R2. One of our customers has chosen to install to VMWare, and what I'm finding is that the VM's are relatively slow compared to hardware. Our product development team has advised that many VMs appear to run particularly slow on I/O benchmarks, which impact performance in production. I've tried the AttoSoft I/O benchmark and find that for smaller I/O blocks (1-32K) the VM I'm looking at is 25x slower than hardware and for larger I/O blocks (1-8MB) it's 10x slower. Is this a fair benchmark? If not, any suggestions for a fair test?

  Read the article

• mount samba share on a vmware instance

  - by Riduidel

  I've a windows machine in which a linux server is run by a "VMWare player". From the windows machine, I want some folders to be mounted on the Linux virtual server. All this is done in a maven build (which is quite irrevelant here, in fact). From what I understand, to make these windows folders available as mountable ones, I have to do the following operations Share the folders as Samba ones using net share, this I have done. Access my virtual server and check which folders are already mounted (which seems to be doable using a less /etc/fstab), this I'll do soon Mount my samba shares using smbmount All that seems to my by far too hackish code. Could the same be done using ... say ... JMX/SNMP or any other high-level technology ?

  Read the article

• virtual machines: optimal host os to run Windows XP guest os?

  - by user61132

  My department doesn't have the budget to upgrade my ailing Dell D620 laptop. However, I do have the option to buy my own personal computer, then use my company-issued ISO image to run Windows XP as my guest os using virtualbox or vmware. Therefore, last month, I bought an Acer AX3910-U3012 desktop that had Windows 7 as the host os (and 8G RAM). In short, I was disappointed with the performance while trying to run WinXP as the guest os. (It didn't perform much better than my laptop.) Just wondering what the optimal host os would be for running Windows XP as the guest os? (No, I can't use my company-issued ISO image to build the os for my personal computer.) FWIW, I'm willing to spend up to $2k if it's REALLY worth it, but would prefer to spend no more than $1k. Also, in an effort to cut costs, I'd prefer buy a desktop instead of a laptop. Thanks for any/all feedback.

  Read the article

• Error connecting ESX 5.0.0 to domain

  - by Saariko

  I am trying to connect an ESX 5.0.0 to our Domain Controler, in order to give a Domain group specific roles security. But I do not see any groups after the host connects to the domain. Under Configuration - Authentication Services - I connected the host to the domain: I created the role I wanted, with the selected approved features But when I want to add a permission to a set of VM's, I can not see "my domain" on the drop down, only the: "localhost" How do I see "my domain" on the Domain drop down - so I can select the domain group to give the role to? To note: I followed the instructions to connect to the domain form VMware site.

  Read the article

• How does a winkydink Teradici offer high res, full FPS, 3D rendering on ESXi 5 VDIs for AutoCAD/SolidWorks/1080p YouTube applications?

  - by BlueToast

  How does such a small Teradici card ![enter image description here][1] offer high resolution, full FPS 3D graphics (1:38) http://www.youtube.com/watch?v=eXA4QMmfY5Y&feature=player_detailpage#t=97s for ESXi 5.0/5.1 VDI environments? We're shooting for an AutoCAD/SolidWorks/YouTube 1080p capable environment. I can't see how such a small and low profile card could possibly have the horsepower to handle such GPU computations for a big environment like that. We're going to have up to 64 VDIs per server, and are a 500-1000 employee count sized company. Someone enlighten me please! Determining which route to go (between RemoteFX and VMware View/PCoIP) and the hardware (NVIDIA 4GB non-Quadro/Tesla GPUs vs Teradici card). Servers have three 4x, three 8x, and one 16x PCI-E lane. Two of the 8x lanes will be occupied by SAS RAID cards.

  Read the article

• Deleted All Snapshots, Now Won't Boot VM with Snapshot not found error

  - by Jharwood

  I've just tried deleting the snapshots from this virtual machine running ESXI5, so that I can grow the Thick Partition. I've now got the below error message when I try to start the VM, the VM also can't be grown above 0 MB i assume for the same reason as below. I've checked the datastore and the original VMDK is still there. Reason: The system cannot find the file specified. Cannot open the disk 'VM1-PG-000002.vmdk' or one of the snapshot disks it depends on. VMware ESX cannot find the virtual disk "VM1-PG-000002.vmdk". Verify the path is valid and try again. How do i tell ESXI5 to use the proper VMDK?

  Read the article

• Access a windows dynamic hard drive through a virtual machine on ubuntu?

  - by Enigma

  I have a Windows 7 OS and am thinking about transitioning to a dual boot set up with Ubuntu 12.04. From what I recall, it is not possible to natively access Dynamic Windows Partitions in a Linux OS. My thought is that it might be possible to have a virtual machine (running windows) installed within Ubuntu access the physical dynamic drive. The problem comes to whether VMWare can access the physical disk "high enough" to be able to mount it within the windows virtual machine as a native device or if it gets passed through from the native Linux OS. This is really the only thing holding me back from switching to a dual-boot set up as the dynamic disk is made up of 4 or 5 hard drives and I would very much like access to the data on both OS's. Alternatively, is there another solution for combining multiple physical hard drives into one virtual hard drive that would be readable on both OS's?

  Read the article

• Is it possible to run a "Windows Server 2008 R2 SP1 Hyper-V Virtual Machine" on Windows 7x64 Pro machine?

  - by tbone

  Specifically, I want to run this: http://www.microsoft.com/en-us/download/details.aspx?displaylang=en&id=27417 This download contains a three Windows Server 2008 R2 SP1 Hyper-V Virtual Machine set for evaluating and demonstrating Office 2010, SharePoint 2010 and Project Server 2010. System requirements Supported operating systems: Windows Server 2008 R2 Additionally you will need: •Windows Server 2008 R2 (SP1 recommended) with the Hyper-V role enabled. •Drive Formatting: NTFS •Processor: Intel VT or AMD-V capable •RAM: 8 GB or more recommended •Hard disk space required for install: 100 GB ------------------------- So, the above text seems to indicate that you need a physical Windows 2008 Server (r2) server running, but from the googling I've done on the subject I've yet to come across a discussion that definitively answers the question. Many posts I've read seem to indicate it might be possible to run it on Windows 7 using one of the following: VirtualBox, Windows Virtual PC, VMWare but I'm not entirely sure.

  Read the article

• Unable to login into CentOS

  - by Rendl

  I had setup a multinode cluster using CentOS with VMware yesterday. Today when I reboot the nodes I get the below error on startup. "there is a problem with the configuration server status 256 centOS" (/usr/libexec/gconf-sanity-check-2 ) I am unable to login as root or any user as the screen is frozen. The solutions online is to change the permissions for some tmp files. My problem is I am unable to access the terminal as I cannot login. Also on reboot I do not have any recovery options in CentOS. I only see command line GRUB. I am new to linux and Hadoop.Pls help asap.

  Read the article

• Windows 2008 R2 on ESXi 4.1 cpu utilization kernel high

  - by MK.

  I have a Win2k8 guest running on ESXi 4.1. The host has 12 cores and the problem happens even if the guest is the only VM on the host. We have 4 cores dedicated to the guest. We noticed that network starts chocking when the CPU load goes up. After some testing we noticed that when running a simple CPU hogging tool set up to run 3 threads at 100% the regular CPU load goes to 75% like it should and the "kernel times" graph in task manager goes up to 25%. My intuition tells me that the network problem and kernel times problem are the same. This is confirmed by another similar VM we created on the same host which doesn't have either of the problems. VMWare tools are obviously installed. The nic is e1000. What else can we do to troubleshoot this?

  Read the article

• vmconvert exchange 2007

  - by user72950

  Has anyone tried to run vmconvert on a Windows 2008 64 bit server running Exchange 2007? Here is what I did. I stopped the Exchange processes and IIS and ran vmconvert. When I moved the new server to my vmware server 2.0 for windows and booted it. All seemed well except I could not send or receive email. All outbound was stuck in the queues. I was able to log in via OWA so that tells the network setup/NIC bindings were OK. Any ideas?

  Read the article

• centos 5.6, virtual on Vsphere

  - by Glasnhost

  suddenly my virtual centos server (5.6 on VMWare-VSphere) is not working... It started with the url not responding, nor the ip. (NO HTTP response, no ping). When I entered on the server via ssh to start troubleshooting I noticed that most of commands don't work anymore: top- machine hangs (it's not slow anyway) ps - machine hangs (funny enough apache server and web app are running and sending me emails) on some directory ls -l - machine hangs after first file, if ls l.txt the file show only the first file "more" command, also hangs on some file. So there are very little things I can try. I recovered my virtual machine from yesterday and before yesterday, and they show the same behaviour, it hangs on commands (but yesterday they were working). There is no firewall on the machine, there is on the host though. I can connect with ftp but I can't download files nor list directory apart the user top directory... Working hard right now, any idea appreciated

  Read the article

• ESXi disaster recovery plan

  - by Marlin

  I have a Vmware infrastructure where I am using the free version of Esxi 5 . I cannot as a result use vmotion and the other cool features that come with a paid ESXI. I am using snapshots for the backups but they are stored on local hard drive. I need a better backup scenario where I can recover in the event of a harddrive failure. I tried openfiler but could not get it right. What backup method can I try given my situation?

  Read the article

• How can I improve the rendering performance of this old DOS application?

  - by MicTech

  I have very old DOS Application (CadSoft Eagle - PCB Designer) and I want to work with it on my workstation with Windows 7. Then I install Windows 98 and that software into VmWare Player. But that software has serious problem with redrawing screen. It's very slow in comparison with my Intel Celeron 333MHz with Windows 98. I have same problem if I try to use DOSBox on Windows XP (same Celeron 333MHz). I also trying run this application directly on Windows XP (same Celeron 333MHz) with compatibility mod set to "Windows 98", but I get "(0Dh): General Protection Fault". Can someone give me good advice how I solve that?

  Read the article

• Windows Server 2008 freezes when I run programs as administrator

  - by user5795

  I am working on a machine running Windows Server 2008. Every program I have tried to run (firefox, notepad, wordpad) works fine, but if I right-click on any item on the desktop or the start menu and select "Run as Administrator" it freezes. I can move the mouse around and open/close the start menu, but the items in the start menu do not change color when the mouse hovers over them. I googled for answers for some time but had no luck. Does anyone have any ideas that I could try? (Update: I forgot to mention that the machine is virtual and I am using VMWare Workstation. In order to answer the questions below, I have been going to the same snapshot of the system each time. This lets me start the system in the exact same place each time in order to answer your questions and test.) (Update: When I run any process as administrator and it freezes, I can start task manager, but I cannot see the new process (notepad, etc...) )

  Read the article

• Disk controller speed responsible for slow write speeds?

  - by vizvayu

  I have question. I'm using ESXi 4.0U1 in an IBM x3200M2 with an integrated LSI 1064e RAID controller, without any kind of cache. I have 3 250GB HOT-SWAP SATA HDs configured in RAID1E (IME). ESXi works fine, read speed are quite OK, but write speeds are incredible slow, never more than 8MB/s, and this is the best case scenario, benchmarking with iozone streaming writes, using a VMWare Paravirtual controller and with only this VM active, no swapping of any kind (total vm memory reserved). Already wrote to IBM but I don't have any kind of pay support so they didn't even answered, so I'm just wondering... anybody has any experience with a similar setup? I just want to be sure this is hardware related and can't be fixed with some kind of config option, because I'm thinking on buying a new RAID controller (Adaptec 2405 looks nice). Thanks again!

  Read the article

• Trouble loading an ISO

  - by crocyson

  I've created a boot disk and ISO image with paragon. I boot up the Virtual pc with the disk in and I get to my recovery page. When I am supposed to select an ISO image? My Virtual PC doesn't acknowledge any of my physical hard drives on my host PC. I've also tried copy/paste the files into my datastore and they do not show up. I've tried the option during the set up to start with the ISO but again I am not able to browse to my external hard drive that I have stored the ISO on. VMWare will acknowledge it and say that it is connected but I can't browse to it. Am I doing something wrong? I created the back up disk and ISO image on the external with paragon.

  Read the article

< Previous Page | 46 47 48 49 50 51 52 53 54 55 56 57  | Next Page >