Search Results

Search found 17420 results on 697 pages for 'static urls'.

Page 52/697 | < Previous Page | 48 49 50 51 52 53 54 55 56 57 58 59  | Next Page >

  • How to set a static route for an external IP address

    - by HorusKol
    Further to my earlier question about bridging different subnets - I now need to route requests for one particular IP address differently to all other traffic. I have the following routing in my iptables on our router: # Allow established connections, and those !not! coming from the public interface # eth0 = public interface # eth1 = private interface #1 (10.1.1.0/24) # eth2 = private interface #2 (129.2.2.0/25) iptables -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT iptables -A INPUT -m state --state NEW ! -i eth0 -j ACCEPT iptables -A FORWARD -i eth0 -o eth1 -m state --state ESTABLISHED,RELATED -j ACCEPT iptables -A FORWARD -i eth0 -o eth2 -m state --state ESTABLISHED,RELATED -j ACCEPT # Allow outgoing connections from the private interfaces iptables -A FORWARD -i eth1 -o eth0 -j ACCEPT iptables -A FORWARD -i eth2 -o eth0 -j ACCEPT # Allow the two private connections to talk to each other iptables -A FORWARD -i eth1 -o eth2 -j ACCEPT iptables -A FORWARD -i eth2 -o eth1 -j ACCEPT # Masquerade (NAT) iptables -t nat -A POSTROUTING -o eth0 -j MASQUERADE # Don't forward any other traffic from the public to the private iptables -A FORWARD -i eth0 -o eth1 -j REJECT iptables -A FORWARD -i eth0 -o eth2 -j REJECT This configuration means that users will be forwarded through a modem/router with a public address - this is all well and good for most purposes, and in the main it doesn't matter that all computers are hidden behind the one public IP. However, some users need to be able to access a proxy at 192.111.222.111:8080 - and the proxy needs to identify this traffic as coming through a gateway at 129.2.2.126 - it won't respond otherwise. I tried adding a static route on our local gateway with: route add -host 192.111.222.111 gw 129.2.2.126 dev eth2 I can successfully ping 192.111.222.111 from the router. When I trace the route, it lists the 129.2.2.126 gateway, but I just get * on each of the following hops (I think this makes sense since this is just a web-proxy and requires authentication). When I try to ping this address from a host on the 129.2.2.0/25 network it fails. Should I do this in the iptables chain instead? How would I configure this routing?

    Read the article

  • Nginx redirect all request that does not match a file to a php file

    - by cyrbil
    I'm trying to get all request to: http://mydomain.com/downloads/* redirect to http://mydomain.com/downloads/index.php except if the requested file exist in /downloads/ ex: http://mydomain.com/downloads = /downloads/index.php http://mydomain.com/downloads/unknowfile = /downloads/index.php http://mydomain.com/downloads/existingfile = /downloads/existingfile My current problem is I have either the redirection to php working but static files not served or the opposite. Here is my current vhost conf: (which redirect fine but static files are send to php and fail) server { listen 80; ## listen for ipv4; this line is default and implied server_name domain.com; root /data/www; index index.php index.html; location / { try_files $uri $uri/ /index.html; } error_page 404 /404.html; # redirect server error pages to the static page /50x.html error_page 500 502 503 504 /50x.html; location = /50x.html { root /usr/share/nginx/www; } location ^~ /downloads { fastcgi_pass unix:/var/run/php5-fpm.sock; fastcgi_split_path_info ^(.+\.php)(/.+)$; fastcgi_index index.php; include fastcgi_params; try_files $uri @downloads; } location @downloads { rewrite ^ /downloads/index.php; } # pass the PHP scripts to FastCGI server # location ~ \.php$ { try_files $uri =404; fastcgi_split_path_info ^(.+\.php)(/.+)$; fastcgi_pass unix:/var/run/php5-fpm.sock; fastcgi_index index.php; include fastcgi_params; } } Precision: static files are symlinks created by /downloads/index.php Thank you for your help.

    Read the article

  • Cisco ASA 5505 network route for static IP hosts

    - by TheCapn
    I've configured my internal VLAN using the most basic settings where ports 1-7 are assigned from a pool of addresses in the range 192.168.15.5 - 192.168.15.36. These hosts are given access to the internet and it works great. What I'm trying to set up now is allowing users who are connected to the device and specify their IP (say I connect and request 192.168.15.45) are given internet access and can still work alongside DHCP hosts. Those with a DHCP assigned address are blocked from the internet. Mostly the issue resides in that I am very new to working with the device. I feel that the solution is easy but I'm not looking in the right spots and don't have the correct terminology down to google it. Do I need to define access control lists? Group policies? a new VLAN? The rules that are set up seem to be specific to the entire /24 subnet but when I request a static IP outside of the DHCP range I get blocked from other hosts and the internet.

    Read the article

  • Sitecore not resolving rich text editor URLS in page renders

    - by adam
    Hi We're having issues inserting links into rich text in Sitecore 6.1.0. When a link to a sitecore item is inserted, it is outputted as: http://domain/~/link.aspx?_id=8A035DC067A64E2CBBE2662F6DB53BC5&_z=z Rather than the actual resolved url: http://domain/path/to/page.aspx This article confirms that this should be resolved in the render pipeline: in Sitecore 6 it inserts a specially formatted link that contains the Guid of the item you want to link to, then when the item is rendered the special link is replaced with the actual link to the item The pipeline has the method ShortenLinks added in web.config <convertToRuntimeHtml> <processor type="Sitecore.Pipelines.ConvertToRuntimeHtml.PrepareHtml, Sitecore.Kernel"/> <processor type="Sitecore.Pipelines.ConvertToRuntimeHtml.ShortenLinks, Sitecore.Kernel"/> <processor type="Sitecore.Pipelines.ConvertToRuntimeHtml.SetImageSizes, Sitecore.Kernel"/> <processor type="Sitecore.Pipelines.ConvertToRuntimeHtml.ConvertWebControls, Sitecore.Kernel"/> <processor type="Sitecore.Pipelines.ConvertToRuntimeHtml.FixBullets, Sitecore.Kernel"/> <processor type="Sitecore.Pipelines.ConvertToRuntimeHtml.FinalizeHtml, Sitecore.Kernel"/> </convertToRuntimeHtml> So I really can't see why links are still rendering in ID format rather than as full SEO-tastic urls. Anyone got any clues? Thanks, Adam

    Read the article

  • 301 Redirecting URLs based on GET variables in .htaccess

    - by technicalbloke
    I have a few messy old URLs like... http://www.example.com/bunch.of/unneeded/crap?opendocument&part=1 http://www.example.com/bunch.of/unneeded/crap?opendocument&part=2 ...that I want to redirect to the newer, cleaner form... http://www.example.com/page.php/welcome http://www.example.com/page.php/prices I understand I can redirect one page to another with a simple redirect i.e. Redirect 301 /bunch.of/unneeded/crap http://www.example.com/page.php But the source page doesn't change, only it's GET vars. I can't figure out how to base the redirect on the value of these GET variables. Can anybody help pls!? I'm fairly handy with the old regexes so I can have a pop at using mod-rewrite if I have to but I'm not clear on the syntax for rewriting GET vars and I'd prefer to avoid the performance hit and use the cleaner Redirect directive. Is there a way? and if not can anyone clue me in as to the right mod-rewrite syntax pls? Cheers, Roger.

    Read the article

  • HTTP POST prarameters order / REST urls

    - by pq
    Let's say that I'm uploading a large file via a POST HTTP request. Let's also say that I have another parameter (other than the file) that names the resource which the file is updating. The resource cannot be not part of the URL the way you can do it with REST (e.g. foo.com/bar/123). Let's say this is due to a combination of technical and political reasons. The server needs to ignore the file if the resource name is invalid or, say, the IP address and/or the logged in user are not authorized to update the resource. Looks like, if this POST came from an HTML form that contains the resource name first and file field second, for most (all?) browsers, this order is preserved in the POST request. But it would be naive to fully rely on that, no? In other words the order of HTTP parameters is insignificant and a client is free to construct the POST in any order. Isn't that true? Which means that, at least in theory, the server may end up storing the whole large file before it can deny the request. It seems to me that this is a clear case where RESTful urls have an advantage, since you don't have to look at the POST content to perform certain authorization/error checking on the request. Do you agree? What are your thoughts, experiences?

    Read the article

  • ExpertPDF and Caching of URLs

    - by Josh
    We are using ExpertPDF to take URLs and turn them into PDFs. Everything we do is through memory, so we build up the request and then read the stream into ExpertPDF and then write the bits to file. All the files we have been requesting so far are just plain HTML documents. Our designers update CSS files or change the HTML and rerequest the documents as PDFs, but often times, things are getting cached. Take, for example, if I rename the only CSS file and view the HTML page through a web browser, the page looks broke because the CSS doesn't exist. But if I request that page through the PDF Generator, it still looks ok, which means somewhere the CSS is cached. Here's the relevant PDF creation code: // Create a request HttpWebRequest request = (HttpWebRequest)HttpWebRequest.Create(url); request.UserAgent = "IE 8.0"; request.ContentType = "application/x-www-form-urlencoded"; request.Method = "GET"; // Send the request HttpWebResponse resp = (HttpWebResponse)request.GetResponse(); if (resp.IsFromCache) { System.Web.HttpContext.Current.Trace.Write("FROM THE CACHE!!!"); } else { System.Web.HttpContext.Current.Trace.Write("not from cache"); } // Read the response pdf.SavePdfFromHtmlStream(resp.GetResponseStream(), System.Text.Encoding.UTF8, "Output.pdf"); When I check the trace file, nothing is being loaded from cache. I checked the IIS log file and found a 200 response coming from the request, even after a file had been updated (I would expect a 302). We've tried putting the No-Cache attribute on all HTML pages, but still no luck. I even turned off all caching at the IIS level. Is there anything in ExpertPDF that might be caching somewhere or something I can do to the request object to do a hard refresh of all resources? UPDATE I put ?foo at the end of my style href links and this updates the CSS everytime. Is there a setting someplace that can prevent stylesheets from being cached so I don't have to do this inelegant solution?

    Read the article

  • (RoR) How to: link multiple apps, multiple URLs, one database

    - by Samson
    Hello. I am currently developing a site using Ruby on Rails. I am still a beginner who just started around a month ago. I use InstantRails on Windows 7. Here's my question. Let's say app A is functional using MYSQL database A_development. The files such as views and controller are under folder 'A'. I now know how to, say for example, link www.app.com to this app by opening port 80 and changing some lines in the mySQL config. In this app, you can register your username, login, and post some messages. I now want to create some pretty identical apps say B and C. The only thing different will be the posts that shows, and the views. You can still log in with the same username, and everything is saved in the same database. I now want the URLs to look something like A.app.com leading to app A, B.app.com leading to app B, etc. Can that be achieved? How? I've been googling for a few days already and I'm still lost. As I'm new to this forum, I'm not quite sure what info do you guys need. Please list and I'll provide them asap. Any help will be appreciated! Thanks.

    Read the article

  • jQuery Mobile and Select menu with URLs

    - by user1907347
    Been battling with this for a while now. I'm trying to get a select menu to work as a navigation menu but I cannot get the URLs to work and have it actually change pages. In the head: <script> $(function() { $("#select-choice-1").click(function() { $.mobile.changePage($("#select-choice-1")); }); }); </script> With this Menu: <div id="MobileWrapper" data-role="fieldcontain"> <select name="select-choice-1" id="select-choice-1" data-theme="a" data-form="ui-btn-up-a" data-mini="true"> <option data-placeholder="true">Navigation</option><!-- data=placeholder makes this not show up in the pop up--> <option value="/index.php" data-ajax="false">Home</option> <option value="/services/index.php" data-ajax="false">Services</option> <option value="/trainers/index.php" data-ajax="false">Trainers</option> <option value="/locations/index.php" data-ajax="false">Locations</option> <option value="/calendar/index.php" data-ajax="false">Calendar</option> <option value="/contactus/index.php" data-ajax="false">Contact Us</option> </select> </div><!--END MobileWrapper DIV-->

    Read the article

  • Django: reverse lookup URL of feeds?

    - by Santa
    I am having trouble doing a reverse URL lookup for Django-generated feeds. I have the following setup in urls.py: feeds = { 'latest': LatestEntries, } urlpatterns = patterns('', # ... # enable feeds (RSS) url(r'^feeds/(?P<url>.*)/$', 'django.contrib.syndication.views.feed', {'feed_dict': feeds}, name='feeds_view'), ) I have tried using the following template tag: <a href="{% url feeds_view latest %}">RSS feeds</a> But the resulting link is not what want (http://my.domain.com/feeds//). It should be http://my.domain.com/feeds/latest/. For now, I am using a hack to generate the URL for the template: <a href="http://{{ request.META.HTTP_HOST }}/feeds/latest">RSS feeds</a> But, as you can see, it clearly is not DRY. Is there something I am missing?

    Read the article

  • django cross-site reverse a url

    - by tutuca
    I have a similar question than django cross-site reverse. But i think I can't apply the same solution. I'm creating an app that lets the users create their own site. After completing the signup form the user should be redirected to his site's new post form. Something along this lines: new_post_url = 'http://%s.domain:9292/manage/new_post %site.domain' logged_user = authenticate(username=user.username, password=user.password) if logged_user is not None: login(request, logged_user) return redirect(new_product_url) Now, I know that "new_post_url" is awful and makes babies cry so I need to reverse it in some way. I thought in using django.core.urlresolvers.reverse to solve this but that only returns urls on my domain, and not in the user's newly created site, so it doesn't works for me. So, do you know a better/smarter way to solve this?

    Read the article

  • django urlconf or .htaccess trouble

    - by Zayatzz
    Hello I am running my django project from subfolder of a website. Lets say the address where my project is meant to open from is. http://example.com/myproject/ the myproject folder is root folder for my user account. In that folder i have fcgi script that starts my project. The .htaccess file in the folder contains this: RewriteEngine On RewriteCond %{REQUEST_FILENAME} !-f RewriteRule ^(.*)$ mysite.fcgi/$1 [QSA,L] The trouble is, that at some cases, instead of redireting user to page like http://example.com/myproject/social/someurl/ it redirects to http://example.com/social/someurl/ which does not work. What i want to know is how to fix this problem. Is this django problem and i should change it with urconf and add myproject to all urls, or should i do this with .htaccess? I found similar question, which, sadly, remains unanswered: http://stackoverflow.com/questions/2321154/how-to-write-htaccess-if-django-project-is-in-subfolder-and-subdomain Alan.

    Read the article

  • KVM network bridge and public static IP for both host and guests

    - by Javier Martinez
    I have a Debian Server with 4 public static addresses. There is a KVM guest (also Debian) installed and running. What I want is to give the guest an IP of the host, so that both machines have public IPs. IP 1: 188.165.A.B IP 2: 178.33.CCC.D IP 3: 178.33.CCC.E IP 4: 178.33.CCC.F What should I do to have connection for host and guest ? This is network conf: # ifconfig br0 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet addr:188.165.A.B Bcast:188.165.255.255 Mask:255.255.255.0 inet6 addr: fe80::ea40:f2ff:fe0a:cc28/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3618 errors:0 dropped:4 overruns:0 frame:0 TX packets:4853 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:599562 (585.5 KiB) TX bytes:1693443 (1.6 MiB) eth0 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet6 addr: fe80::ea40:f2ff:fe0a:cc28/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:4274 errors:0 dropped:0 overruns:0 frame:0 TX packets:4879 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:720045 (703.1 KiB) TX bytes:1715641 (1.6 MiB) Interrupt:20 Memory:fe500000-fe520000 eth0:0 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet addr:178.33.CCC.D Bcast:178.33.255.255 Mask:255.255.255.255 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:20 Memory:fe500000-fe520000 eth0:1 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet addr:178.33.CCC.E Bcast:178.33.255.255 Mask:255.255.255.255 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:20 Memory:fe500000-fe520000 eth0:2 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet addr:178.33.CCC.F Bcast:178.33.255.255 Mask:255.255.255.255 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:20 Memory:fe500000-fe520000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:27932 errors:0 dropped:0 overruns:0 frame:0 TX packets:27932 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1820862 (1.7 MiB) TX bytes:1820862 (1.7 MiB) vnet0 Link encap:Ethernet HWaddr fe:54:00:87:40:ec inet6 addr: fe80::fc54:ff:fe87:40ec/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:18 errors:0 dropped:0 overruns:0 frame:0 TX packets:204 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:1452 (1.4 KiB) TX bytes:16958 (16.5 KiB) #route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface default aa.bb.cc.eu 0.0.0.0 UG 0 0 0 br0 188.165.255.0 * 255.255.255.0 U 0 0 0 br0 # brctl show bridge name bridge id STP enabled interfaces br0 8000.e840f20acc28 no eth0 vnet0 There is no firewall enabled and DNS is configured properly. What I want to achieve: | | | +----+-------------------------+-+------+ | | Host | | | | | | | | | | +------------+------+ | | eth0 | eth0:0-1 | | | 188.165.A.B | | | | | | | | | br0 vnet0 | | | +------------+------+ | | | | | | | | +------------+------+ | | | | | | | | eth0:2-+ | | | | 178.33.CCC.F | | | | | | | | Guest | | | +-------------------+ | +---------------------------------------+ Thanks you

    Read the article

  • KVM network bridge and public static IP for both host and guests

    - by Javier Martinez
    I have a Debian Server with 4 public static addresses. There is a KVM guest (also Debian) installed and running. What I want is to give the guest an IP of the host, so that both machines have public IPs. IP 1: 188.165.A.B IP 2: 178.33.CCC.D IP 3: 178.33.CCC.E IP 4: 178.33.CCC.F What should I do to have connection for host and guest ? This is network conf: # ifconfig br0 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet addr:188.165.A.B Bcast:188.165.255.255 Mask:255.255.255.0 inet6 addr: fe80::ea40:f2ff:fe0a:cc28/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3618 errors:0 dropped:4 overruns:0 frame:0 TX packets:4853 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:599562 (585.5 KiB) TX bytes:1693443 (1.6 MiB) eth0 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet6 addr: fe80::ea40:f2ff:fe0a:cc28/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:4274 errors:0 dropped:0 overruns:0 frame:0 TX packets:4879 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:720045 (703.1 KiB) TX bytes:1715641 (1.6 MiB) Interrupt:20 Memory:fe500000-fe520000 eth0:0 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet addr:178.33.CCC.D Bcast:178.33.255.255 Mask:255.255.255.255 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:20 Memory:fe500000-fe520000 eth0:1 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet addr:178.33.CCC.E Bcast:178.33.255.255 Mask:255.255.255.255 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:20 Memory:fe500000-fe520000 eth0:2 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet addr:178.33.CCC.F Bcast:178.33.255.255 Mask:255.255.255.255 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:20 Memory:fe500000-fe520000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:27932 errors:0 dropped:0 overruns:0 frame:0 TX packets:27932 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1820862 (1.7 MiB) TX bytes:1820862 (1.7 MiB) vnet0 Link encap:Ethernet HWaddr fe:54:00:87:40:ec inet6 addr: fe80::fc54:ff:fe87:40ec/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:18 errors:0 dropped:0 overruns:0 frame:0 TX packets:204 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:1452 (1.4 KiB) TX bytes:16958 (16.5 KiB) #route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface default aa.bb.cc.eu 0.0.0.0 UG 0 0 0 br0 188.165.255.0 * 255.255.255.0 U 0 0 0 br0 # brctl show bridge name bridge id STP enabled interfaces br0 8000.e840f20acc28 no eth0 vnet0 There is no firewall enabled and DNS is configured properly. What I want to achieve: | | | +----+-------------------------+-+------+ | | Host | | | | | | | | | | +------------+------+ | | eth0 | eth0:0-1 | | | 188.165.A.B | | | | | | | | | br0 vnet0 | | | +------------+------+ | | | | | | | | +------------+------+ | | | | | | | | eth0:2-+ | | | | 178.33.CCC.F | | | | | | | | Guest | | | +-------------------+ | +---------------------------------------+ Thanks you

    Read the article

  • url template tag in django template

    - by user192048
    guys: I was trying to use the url template tag in django, but no lucky, I defined my urls.py like this urlpatterns = patterns('', url(r'^analyse/$', views.home, name="home"), url(r'^analyse/index.html', views.index, name="index"), url(r'^analyse/setup.html', views.setup, name="setup"), url(r'^analyse/show.html', views.show, name="show"), url(r'^analyse/generate.html', views.generate, name="generate"), I defined the url pattern in my view like this {% url 'show'%} then I got this error message Caught an exception while rendering: Reverse for ''show'' with arguments '()' and keyword arguments '{}' not found. Original Traceback (most recent call last): File "/Library/Python/2.5/site-packages/django/template/debug.py", line 71, in render_node result = node.render(context) File "/Library/Python/2.5/site-packages/django/template/defaulttags.py", line 155, in render nodelist.append(node.render(context)) File "/Library/Python/2.5/site-packages/django/template/defaulttags.py", line 382, in render raise e NoReverseMatch: Reverse for ''show'' with arguments '()' and keyword arguments '{}' not found. I am wondering why django failed to render? what is the right way to define it in the tempalte?

    Read the article

  • Pxe net install Centos with Static IP

    - by Stu2000
    I seem to be unable to perform a kickstart installation of centos5.8 with a netinstall. It correctly gets into the text installer, but keeps sending out a request for the dhcp server and failing. I have tried to manually set the IP everywhere. Here is my pxelinux.cfg file DEFAULT menu PROMPT 0 MENU TITLE Ubuntu MAAS TIMEOUT 200 TOTALTIMEOUT 6000 ONTIMEOUT local LABEL centos5.8-net kernel /images/centos5.8-net/vmlinuz MENU LABEL centos5.8-net append initrd=/images/centos5.8-net/initrd.img ip=192.168.1.163 netmask=255.255.255.0 hostname=client101 gateway=192.168.1.1 ksdevice=eth0 dns=8.8.8.8 ks=http://192.168.1.125/cblr/svc/op/ks/profile/centos5.8-net MENU end and here is my kickstart file: # Kickstart file for a very basic Centos 5.8 system # Assigns the server ip: 192.211.48.163 # DNS 8.8.8.8, 8.8.4.4 # London TZ install url --url http://mirror.centos.org/centos-5/5.8/os/i386 lang en_US.UTF-8 keyboard us network --device=eth0 --bootproto=static --ip=192.168.1.163 --netmask=255.255.255.0 --gateway=192.168.1.1 --nameserver=8.8.8.8,8.8.4.4 --hostname=client1-server --onboot=on rootpw --iscrypted $1$Snrd2bB6$CuD/07AX2r/lHgVTPZyAz/ firewall --enabled --port=22:tcp authconfig --enableshadow --enablemd5 selinux --enforcing timezone --utc Europe/London bootloader --location=mbr --driveorder=xvda --append="console=xvc0" # The following is the partition information you requested # Note that any partitions you deleted are not expressed # here so unless you clear all partitions first, this is # not guaranteed to work part /boot --fstype ext3 --size=100 --ondisk=xvda part pv.2 --size=0 --grow --ondisk=xvda volgroup VolGroup00 --pesize=32768 pv.2 logvol swap --fstype swap --name=LogVol01 --vgname=VolGroup00 --size=528 --grow --maxsize=1056 logvol / --fstype ext3 --name=LogVol00 --vgname=VolGroup00 --size=1024 --grow %packages @base @core @dialup @editors @text-internet keyutils iscsi-initiator-utils trousers bridge-utils fipscheck device-mapper-multipath sgpio emacs Here is my dhcp file: ddns-update-style interim; allow booting; allow bootp; ignore client-updates; set vendorclass = option vendor-class-identifier; subnet 192.168.1.0 netmask 255.255.255.0 { host tower { hardware ethernet 50:E5:49:18:D5:C6; fixed-address 192.168.1.163; option routers 192.168.1.1; option domain-name-servers 8.8.8.8,8.8.4.4; option subnet-mask 255.255.255.0; filename "/pxelinux.0"; default-lease-time 21600; max-lease-time 43200; next-server 192.168.1.125; } } Is it impossible to prevent it asking for a dynamic ip before trying to install from the net? Perhaps there is an error in of my files? My dhcp server is set to ignore client-updates, and is set to only works with one mac address whilst testing.

    Read the article

  • htaccess, remove text from url

    - by Keiron Lowe
    Here is the email from the client explaining what he is trying to do, we have spent hours trying to sort out this problem but cannot find a solution that works. I am trying to correct a problem with my blog and google “not found” URLs. I thought it might be very simple to correct (!ha!) This is my line of code; RewriteCond %{THE_REQUEST} ^www.uk-domestic-cleaning.com/wpblog/tag/?(.*)/HomeMaid%20Domestic%20Cleaning$ RewriteRule ^wpblog\/tag\/?(.*)\/HomeMaid%20Domestic%20Cleaning$ "http\:\/\/www\.uk\-domestic\-cleaning\.com\/wpblog\/tag\/$1" [R=301,L] What I am trying to do is any request to */wplog/tag/ “anything here”/HomeMaid Domestic Cleaning To strip the “HomeMaid Domestic Cleaning” bit off the end, but leave the rest of the request intact, which will then be a valid request. Any idea's guys?

    Read the article

  • Nginx + Wordpress Multisite 3.4.2 + subdirectories + static pages and permalinks

    - by UrkoM
    I am trying to setup Wordpress Multisite, using subdirectories, with Nginx, php5-fpm, APC, and Batcache. As many other people, I am getting stuck in the rewrite rules for permalinks. I have followed these two guides, which seem to be as official as you can get: http://evansolomon.me/notes/faster-wordpress-multisite-nginx-batcache/ http://codex.wordpress.org/Nginx#WordPress_Multisite_Subdirectory_rules It is partially working: http://blog.ssis.edu.vn works. http://blog.ssis.edu.vn/umasse/ works. But other permalinks, like these two to a post or to a static page, don't work: http://blog.ssis.edu.vn/umasse/2008/12/12/hello-world-2/ http://blog.ssis.edu.vn/umasse/sample-page/ They either take you to a 404 error, or to some other blog! Here is my configuration: server { listen 80 default_server; server_name blog.ssis.edu.vn; root /var/www; access_log /var/log/nginx/blog-access.log; error_log /var/log/nginx/blog-error.log; location / { index index.php; try_files $uri $uri/ /index.php?$args; } # Add trailing slash to */wp-admin requests. rewrite /wp-admin$ $scheme://$host$uri/ permanent; # Add trailing slash to */username requests rewrite ^/[_0-9a-zA-Z-]+$ $scheme://$host$uri/ permanent; # Directives to send expires headers and turn off 404 error logging. location ~* \.(js|css|png|jpg|jpeg|gif|ico)$ { expires 24h; log_not_found off; } # this prevents hidden files (beginning with a period) from being served location ~ /\. { access_log off; log_not_found off; deny all; } # Pass uploaded files to wp-includes/ms-files.php. rewrite /files/$ /index.php last; if ($uri !~ wp-content/plugins) { rewrite /files/(.+)$ /wp-includes/ms-files.php?file=$1 last; } # Rewrite multisite '.../wp-.*' and '.../*.php'. if (!-e $request_filename) { rewrite ^/[_0-9a-zA-Z-]+(/wp-.*) $1 last; rewrite ^/[_0-9a-zA-Z-]+.*(/wp-admin/.*\.php)$ $1 last; rewrite ^/[_0-9a-zA-Z-]+(/.*\.php)$ $1 last; } location ~ \.php$ { # Forbid PHP on upload dirs if ($uri ~ "uploads") { return 403; } client_max_body_size 25M; try_files $uri =404; fastcgi_pass unix:/var/run/php5-fpm.sock; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; include /etc/nginx/fastcgi_params; } } Any ideas are welcome! Have I done something wrong? I have disabled Batcache to see if it makes any difference, but still no go.

    Read the article

  • Django: Site-Wide URL Prefix

    - by Tom
    I've built a Django site that will live at the root when it's live. Right now it's functioning perfectly at the IP address. For testing purposes, the client has pointed a proxy url at it, but the url has /folder/path in it, so none of the URL patterns match. I put (/folder/path)? into all the url patterns so they now respond, but all of the links are broken because I'm using the {% url %} tag and while the url patterns will match the optional path, they don't include it in that tag. Clearly I can just hard-code /folder/path into all of my urls (well, into all of the url includes) until testing is complete, but is there a better way to do this?

    Read the article

  • How can I view the all inherited url-resolution rules affecting a given directory?

    - by john.designop.us
    I work on two sites hosted on the same server, using the same CMS configurations and identical .htaccess files in their respective document roots. One site is letting me use the CMS's clean-url mode, and the other isn't. Site #2 functions fine in ?=messy-url mode, but when I turn clean urls on in the admin panel, and request a rewritten URL, I get a 404 error served before the CMS sees the request. I've contacted the server administrator, but he isn't inclined to provide support and the site owners are beholden to this hosting provider. I have shell access to the Linux-based server, and I can verify that mod_php and mod_rewrite are active, but I don't know what more I can do to troubleshoot this issue. Is there any way to identify directives upstream that may be differentiating the way http requests are handled by the two sites? Thanks!

    Read the article

  • Using non-Railsy route to prepopulate a form

    - by user94154
    I have many instances of a Rails model, Post. When viewing an individual post, I'd like to create a form to create a child of Post called Comment. I'd like to prepopulate this form with a hidden tag that contains the post_id which is the foreign key in Comment. The Railsy way to do this is to create a fancy-ish route such as: /comments/new/post/:post_id However, this gunks up the routes file and doesn't leave much flexibility. Let's say I want to create a link somewhere else that prepopulates a different attribute of the form...then I'd have to add another route for this. So I think I'm going to create urls like this on /posts/show/:id: /comments/new?comment[post_id]=<%= @post.id %> This way I can add any other attributes as I need. I know the plus side associated with this, now what are the downsides?

    Read the article

  • What can Haskell's type system do that Java's can't?

    - by Matt Fenwick
    I was talking to a friend about the differences between the type systems of Haskell and Java. He asked me what Haskell's could do that Java's couldn't, and I realized that I didn't know. After thinking for a while, I came up with a very short list of minor differences. Not being heavy into type theory, I'm left wondering whether they're formally equivalent. To try and keep this from becoming a subjective question, I'm asking: what are the major, non-syntactical differences between their type systems? I realize some things are easier/harder in one than in the other, and I'm not interested in talking about those. And to make it more specific, let's ignore Haskell type extensions since there's so many out there that do all kinds of crazy/cool stuff.

    Read the article

  • What can Haskell's type system do that Java's can't and vice versa?

    - by Matt Fenwick
    I was talking to a friend about the differences between the type systems of Haskell and Java. He asked me what Haskell's could do that Java's couldn't, and I realized that I didn't know. After thinking for a while, I came up with a very short list of minor differences. Not being heavy into type theory, I'm left wondering whether they're formally equivalent. To try and keep this from becoming a subjective question, I'm asking: what are the major, non-syntactical differences between their type systems? I realize some things are easier/harder in one than in the other, and I'm not interested in talking about those. And to make it more specific, let's ignore Haskell type extensions since there's so many out there that do all kinds of crazy/cool stuff.

    Read the article

  • Type checking and recursive types (Writing the Y combinator in Haskell/Ocaml)

    - by beta
    When explaining the Y combinator in the context of Haskell, it's usually noted that the straight-forward implementation won't type-check in Haskell because of its recursive type. For example, from Rosettacode [1]: The obvious definition of the Y combinator in Haskell canot be used because it contains an infinite recursive type (a = a -> b). Defining a data type (Mu) allows this recursion to be broken. newtype Mu a = Roll { unroll :: Mu a -> a } fix :: (a -> a) -> a fix = \f -> (\x -> f (unroll x x)) $ Roll (\x -> f (unroll x x)) And indeed, the “obvious” definition does not type check: ?> let fix f g = (\x -> \a -> f (x x) a) (\x -> \a -> f (x x) a) g <interactive>:10:33: Occurs check: cannot construct the infinite type: t2 = t2 -> t0 -> t1 Expected type: t2 -> t0 -> t1 Actual type: (t2 -> t0 -> t1) -> t0 -> t1 In the first argument of `x', namely `x' In the first argument of `f', namely `(x x)' In the expression: f (x x) a <interactive>:10:57: Occurs check: cannot construct the infinite type: t2 = t2 -> t0 -> t1 In the first argument of `x', namely `x' In the first argument of `f', namely `(x x)' In the expression: f (x x) a (0.01 secs, 1033328 bytes) The same limitation exists in Ocaml: utop # let fix f g = (fun x a -> f (x x) a) (fun x a -> f (x x) a) g;; Error: This expression has type 'a -> 'b but an expression was expected of type 'a The type variable 'a occurs inside 'a -> 'b However, in Ocaml, one can allow recursive types by passing in the -rectypes switch: -rectypes Allow arbitrary recursive types during type-checking. By default, only recursive types where the recursion goes through an object type are supported. By using -rectypes, everything works: utop # let fix f g = (fun x a -> f (x x) a) (fun x a -> f (x x) a) g;; val fix : (('a -> 'b) -> 'a -> 'b) -> 'a -> 'b = <fun> utop # let fact_improver partial n = if n = 0 then 1 else n*partial (n-1);; val fact_improver : (int -> int) -> int -> int = <fun> utop # (fix fact_improver) 5;; - : int = 120 Being curious about type systems and type inference, this raises some questions I'm still not able to answer. First, how does the type checker come up with the type t2 = t2 -> t0 -> t1? Having come up with that type, I guess the problem is that the type (t2) refers to itself on the right side? Second, and perhaps most interesting, what is the reason for the Haskell/Ocaml type systems to disallow this? I guess there is a good reason since Ocaml also will not allow it by default even if it can deal with recursive types if given the -rectypes switch. If these are really big topics, I'd appreciate pointers to relevant literature. [1] http://rosettacode.org/wiki/Y_combinator#Haskell

    Read the article

  • How to solve 404 for static files with Django and Nginx?

    - by Lucio
    I setup a Trusty VM with Django + Nginx (other stuffs too). The server is working, I get the "Welcome to Django" page. But when I enter to servername/admin it loads the HTML page but fails to load the static content. And the admin page have this links to static content: <link rel="stylesheet" type="text/css" href="/static/admin/css/base.css" /> <link rel="stylesheet" type="text/css" href="/static/admin/css/login.css" /> Both of the CSS files give me 404, as the Nginx log shows: 192.168.56.1 - - [05/Jun/2014:12:04:09 -0300] "GET /admin HTTP/1.1" 301 5 "-" "Mozilla/5.0 (X11; Ubuntu; Linux x86_64; rv:29.0) Gecko/20100101 Firefox/29.0" 192.168.56.1 - - [05/Jun/2014:12:04:09 -0300] "GET /admin/ HTTP/1.1" 200 833 "-" "Mozilla/5.0 (X11; Ubuntu; Linux x86_64; rv:29.0) Gecko/20100101 Firefox/29.0" 192.168.56.1 - - [05/Jun/2014:12:04:10 -0300] "GET /static/admin/css/base.css HTTP/1.1" 404 142 "http://ubuntu-server/admin/" "Mozilla/5.0 (X11; Ubuntu; Linux x86_64; rv:29.0) Gecko/20100101 Firefox/29.0" 192.168.56.1 - - [05/Jun/2014:12:04:10 -0300] "GET /static/admin/css/login.css HTTP/1.1" 404 142 "http://ubuntu-server/admin/" "Mozilla/5.0 (X11; Ubuntu; Linux x86_64; rv:29.0) Gecko/20100101 Firefox/29.0" I think that the error is on my nginx.conf file, but do not know how to solve it.

    Read the article

< Previous Page | 48 49 50 51 52 53 54 55 56 57 58 59  | Next Page >