Search Results

Search found 18209 results on 729 pages for 'loop device'.

Page 60/729 | < Previous Page | 56 57 58 59 60 61 62 63 64 65 66 67  | Next Page >

• how to use iptables to block the IP of device connected to openwrt router

  - by scola

  I have two routers(A,B).the A connect to internet with IP:192.168.1.1 The openwrt router B connect the lan of A by bridge with static IP:192.168.1.111. I am learning to use iptables to control the devices connected to B(wlan) . I use my phone to connect wifi of B,the phone's IP is IP:192.168.1.100.it can surf the internet normally. I want to block the phone's IP to make the phone can not connect to internet. refer to http://bredsaal.dk/some-small-iptables-on-openwrt-tips iptables -A input_wan -s 192.168.1.100 --jump REJECT iptables -A forwarding_rule -d 192.168.1.100 --jump REJECT but it do not work.the phone still connect to internet normally. and I tried other chain(INPUT,OUTPUT,FORWARD).so many chains confused me. iptables -I OUTPUT -o br-lan -s 192.168.1.100 -j DROP and it do not work again. I'm sure that the iptables have no problem. root@OpenWrt:/etc# iptables -L|grep Chain Chain INPUT (policy ACCEPT) Chain FORWARD (policy DROP) Chain OUTPUT (policy ACCEPT) Chain forward (1 references) Chain forwarding_lan (1 references) Chain forwarding_rule (1 references) Chain forwarding_wan (1 references) Chain input (1 references) Chain input_lan (1 references) Chain input_rule (1 references) Chain input_wan (1 references) Chain output (1 references) root@OpenWrt:/etc# ifconfig br-lan Link encap:Ethernet HWaddr 0C:82:68:97:57:BA inet addr:192.168.1.111 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::e82:68ff:fe97:57ba/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:14976 errors:0 dropped:0 overruns:0 frame:0 TX packets:7656 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:2851980 (2.7 MiB) TX bytes:1902785 (1.8 MiB) eth0 Link encap:Ethernet HWaddr 0C:82:68:97:57:BA UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:58201 errors:0 dropped:11 overruns:0 frame:0 TX packets:45012 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:54591348 (52.0 MiB) TX bytes:5711142 (5.4 MiB) Interrupt:4 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:312 errors:0 dropped:0 overruns:0 frame:0 TX packets:312 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:39961 (39.0 KiB) TX bytes:39961 (39.0 KiB) mon.wlan0 Link encap:UNSPEC HWaddr 0C-82-68-97-57-BA-00-48-00-00-00-00-00-00-00-00 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:4900 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:32 RX bytes:1223807 (1.1 MiB) TX bytes:0 (0.0 B) wlan0 Link encap:Ethernet HWaddr 0C:82:68:97:57:BA UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:37346 errors:0 dropped:0 overruns:0 frame:0 TX packets:49662 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:32 RX bytes:3808021 (3.6 MiB) TX bytes:54486310 (51.9 MiB) root@OpenWrt:/etc/config# cat network config 'interface' 'loopback' option 'ifname' 'lo' option 'proto' 'static' option 'ipaddr' '127.0.0.1' option 'netmask' '255.0.0.0' config 'interface' 'lan' option 'ifname' 'eth0' option 'type' 'bridge' option 'proto' 'static' option 'ipaddr' '192.168.1.111' option 'netmask' '255.255.255.0' option 'gateway' '192.168.1.1' option dns 192.168.1.1 and how to use iptables to control the network of wlan? Thanks in advance and sorry for poor English.

  Read the article

• Devices renamed with udev not working, original device node still there

  - by skerit

  I'm trying to rename certain video devices using udev. Here's a rule (broken down for readability): ACTION=="add", SUBSYSTEM=="usb", ATTR{busnum}=="1", ATTR{devpath}=="2", ATTR{idVendor}=="05e1", NAME="video97" It works. /dev/video97 is created But the original /dev/video1 node is STILL there. The even worse, when I try to view the /dev/video97 node in guvcview it doesn't work, while the original node DOES work.

  Read the article

• Nginx HTTPS redirects causing loop

  - by Ben Chiappetta

  I've been banging my head against the wall trying to figure this out, so if anyone can help I'd appreciate it. My Nginx conf has three different redirect loops, haven't been able to get any of the three to work right. The three problem areas are: Redirecting memcache directory to SSL Redirecting accounts directory to SSL Redirecting SSL to www if non-www nginx.conf: user nginx; worker_processes 1; error_log /var/log/nginx/error.log warn; pid /var/run/nginx.pid; events { worker_connections 1024; } http { include /etc/nginx/mime.types; default_type application/octet-stream; log_format main '$remote_addr - $remote_user [$time_local] "$request" ' '$status $body_bytes_sent "$http_referer" ' '"$http_user_agent" "$http_x_forwarded_for"'; access_log /var/log/nginx/access.log main; error_log /var/log/nginx/error.log notice; sendfile on; #tcp_nopush on; keepalive_timeout 65; proxy_set_header X-Url-Scheme $scheme; #gzip on; rewrite_log on; include /etc/nginx/conf.d/*.conf; } conf.d/default.conf: server { listen 80; server_name <redacted>.net; rewrite ^(.*) http://www.<redacted>.net$1; } server { listen 80; server_name www.<redacted>.net; set_real_ip_from 192.168.30.4; set_real_ip_from 192.168.30.5; set_real_ip_from 192.168.30.10; real_ip_header X-Forwarded-For; #charset koi8-r; access_log /var/log/nginx/host.access.log main; root /var/www/html; index index.php index.html index.htm; location =/memcache { rewrite ^/(.*)$ https://$server_name$request_uri? permanent; } location /accounts { rewrite ^/(.*)$ https://$server_name$request_uri? permanent; } #error_page 404 /404.html; # redirect server error pages to the static page /50x.html # error_page 500 502 503 504 /50x.html; location = /50x.html { } # pass the PHP scripts to FastCGI server listening on 127.0.0.1:9000 # location ~ \.php$ { fastcgi_pass 127.0.0.1:9000; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; include /etc/nginx/fastcgi_params; try_files $uri = 404; } # deny access to .htaccess files, if Apache's document root # concurs with nginx's one # location ~ /\.ht { deny all; } } conf.d/ssl.conf: # HTTPS server # server { listen 443; server_name <redacted>.net; rewrite ^(.*) https://www.<redacted>.net$1; } server { listen 443 default_server ssl; server_name www.<redacted>.net; set_real_ip_from 192.168.30.4; set_real_ip_from 192.168.30.5; set_real_ip_from 192.168.30.10; real_ip_header X-Forwarded-For; proxy_set_header X-Forwarded_Proto https; proxy_set_header Host $host; proxy_redirect off; proxy_max_temp_file_size 0; proxy_set_header X-Forwarded-Ssl on; set $https_enabled on; ssl_certificate <redacted>.crt; ssl_certificate_key <redacted>.key; ssl_session_timeout 5m; ssl_protocols SSLv2 SSLv3 TLSv1; ssl_ciphers HIGH:!aNULL:!MD5; ssl_prefer_server_ciphers on; root /var/www/html; index index.php index.html index.htm; location /memcache { auth_basic "Restricted"; auth_basic_user_file $document_root/memcache/.htpasswd; } location ~ \.php$ { fastcgi_pass 127.0.0.1:9000; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; fastcgi_param HTTPS on; include /etc/nginx/fastcgi_params; try_files $uri = 404; } }

  Read the article

• Remove USB device from command line

  - by Luke

  I'm constructing a backup script for Windows 7, and the last action I want it to perform is to safely "remove" the USB drive that it is backing up to. I am under the impression that plugging the drive into the SAME USB port all the time will keep the same DEV_ID, correct me if I'm wrong. With a Command Line (or PowerShell), how can I tell Windows to safely remove the hardware automatically without user input? Just as a place holder, other OSes that may have a way to do this would be great to know as well

  Read the article

• Multi device BTRFS filesystem with disk of different size

  - by fokenrute

  I have an existing BTRFS filesystem composed of one 500GB disk and I just bought a 2TB disk to increase the storage capacity of my home server and I want add the new disk to the existing filesystem. From what I read, it seems like no BTRFS setup can handle disk of different sizes without wasting the difference in size between the larger and the smaller disk, but I'm new to BTRFS and I might have missed something, so is there a setup that can allow me to combine two disks in a filesystem without wasting space ?

  Read the article

• Network Block Device (NBD) clients for Windows or similar solutions

  - by przemoc

  Are there any NBD clients for Windows? Strangely, I cannot find any, or I am searching for them in a wrong way. Such client should be possibly a driver with front-end tool (may be a command-line one) allowing to create virtual drives and associate them with given hosts (or simply localhost) and ports where NBD servers are listening. From user perspective virtual drive should be close to what physical drive is, so it should be accessible as something like \\.\PhysicalDriveX (maybe \\.\VirtualDriveX?), be visible in Disk Management (diskmgmt.msc) and mountvol tools at least. (The only thing I found remotely close to NBD on Windows is ImDisk's proxy mode and companion tool devio, but AFAIK ImDisk only works at partition level (so no virtual drive) and devio uses different protocol.) Secondary question is: Are there any (preferably simple) Windows-specific solutions allowing creation of virtual drive delegating read/write request to user-space via some explicit way (like via TCP, IPC, DLL implementing given API, etc.)?

  Read the article

• USB port causing device problems after new motherboard upgrade

  - by enbuyukfener

  I'm looking into a PC with an issue with one of the front USB ports (perhaps both). It was working before a motherboard upgrade but since then, a USB drive was inserted, overheated and does not appear to be working. Then a phone (with USB charging) was plugged in, and the phone OS suspended. Removing and re-inserting the battery led to the phone (and hence battery) working, however the battery no longer charges (including with a wall charger). It seems too much to be a coincidence and am wondering what the issue may be? Ideas so far are short circuiting, or over-current to the USB ports. Note: Did not occur to me, so details are not 100% accurate or complete. Feel free to ask for missing info that I may have forgotten though.

  Read the article

• Problems when loop over a series of ssh-ed commands

  - by Jack Medley

  I have a series of server machines which I want to run the same command on. Each command takes hours and (even though I am running the commands using nohup and setting them to run in the background) I have to wait for each to finish before the next starts. Here is roughly how I have set it up: On the host machines: for i in {1..9}; do ssh RemoteMachine${i} ./RunJobs.sh; done Where RunJobs.sh on each remote machine is: source ~/.bash_profile cd AriadneMatching for file in FileDirectory/Input_*; do nohup ./Executable ${file} & done exit Does anyone know of a way such that I dont have to wait for each job to finish before the next starts? Or alternatively a better way of doing this, I have a feeling what I am do is fairly sub-optimal. Cheers, Jack

  Read the article

• Linking two networks that have a common device

  - by Serban Razvan

  I recently bought a Samsung Smart TV having in mind to connect it to the Internet. Because my router is very far from it and not wanting to buy an expensive wireless for the TV, I created a homemade solution. I have the laptop (an smartphone and the PC) connected to the router which is connected to the internet. I shared the laptop's wireless connection to the ethernet port which I connected to the TV. So far, the TV is connected to the internet, but is there any way to make him part of the router's network instead of the 2 devices network (the laptop and the TV)?

  Read the article

• ATI driver in Fedora linux 11

  - by unknown (google)

  I recently built a pc with an ATI Radeon HD 5750. I have installed Fedora 11 and installed the device driver for the Radeon 5700 series proprietary drivers. I wanted to see if there is graphics hardware acceleration. I typed in glxinfo at the terminal and I got: X Error of failed request: BadRequest (invalid request code or no such operation) Major opcode of failed request: 135 (GLX) Minor opcode of failed request: 19 (X_GLXQueryServerString) Serial number of failed request: 14 Current serial number in output stream: 14 I don't know how to fix this. I tried to go to the ATI Catalyst Control Center; that worked, but the ATI Catalyst Control Center (Administrator) doesn't work. If anyone knows how to fix this problem then please let me know. Thanks

  Read the article

• Binding keys from specific device in X.org

  - by Michal Cihar

  I have a remote control for presentations, which generates Next/Prior key events in X.org (Page up/down). I'd like to use these for navigating in playlist (using MPD, but it probably does not matter). The problem is that I want to make this control work all the time (without application having focus) and I don't want to lose Page up/down functionality from normal keyboard. Is there some application which would allow me to bind actions to events from specific keyboard? Or is there simple way to implement such thing on my own?

  Read the article

• how to access a mounted device, How can I access the partitions with the console

  - by user1796624

  Hi I'm new to ubuntu and linux so this might be a very begginers question. I have several partitions on my pc and I want to be able to access them with the console. When I type: sudo fdisk -l I get: /dev/sda1 * 2048 97656831 48827392 7 HPFS/NTFS/exFAT /dev/sda2 97656832 234375167 68359168 7 HPFS/NTFS/exFAT /dev/sda3 * 234375168 312500223 39062528 83 Linux /dev/sda4 312502270 625141759 156319745 5 Extended /dev/sda5 312502272 318359551 2928640 82 Linux swap / Solaris /dev/sda6 318361600 625141759 153390080 83 Linux But it seams that the address is existing. for example I cant do cd /dev/sda4. How can I access the partitions with the console?

  Read the article

• Plug-in device to front USB computer *sometimes* restarts

  - by Mark A. Nicolosi

  I've got a strange problem that very occasionally (maybe once a month) when I plug-in something to the front USB on my computer, the computer suddently restarts. This also happens when I touch the front USB ports sometimes. This has been going on for a few years and a lot of the components in my PC have changed. I thought it was my home wiring, but I moved last year and it still happened. I thought maybe it was the motherboard, but that was upgraded 9 months ago and it still happens. I thought it was my case, but I changed that recently and it still happens. I thought maybe it was my PSU, but I upgraded that yesterday and it still happens. I'm pretty sure this is an electro-static thing, but I thought that modern computers have protection against this sort of thing. Maybe I should move my case off the floor (carpet) and stop wearing songs all the time. Edit: Just to clarify this is a computer that I built. The components have been upgraded throughout the years and it's not much the same computer anymore. This doesn't happen very often, but it is annoying, because I don't know what the cause is. Anyone have any ideas?

  Read the article

• Powershell enters foreach loop with null object

  - by SteB

  I'm listing all backups in a given directory: $backups = Get-ChildItem -Path $zipFilepath | Where-Object {($_.lastwritetime -lt (Get-Date).addDays(-7)) -and (-not $_.PSIsContainer) -and ($_.Name -like "backup*")} If I set it to deliberately return no files (.addDays(-600) then the following prints "Empty" (as expected): if (!$backups) { "Empty" } If I try to list the names with an empty $backups variable: foreach ($file in $backups) { $file.FullName; } I get nothing (as expected), if I change this to: "test"+ $file.FullName; then I get a single "test" under the "Empty". How is this possible if $backups is empty?

  Read the article

• An device with an unknown MAC address is connected to my router

  - by Yar

  There is a computer that is not mine that is accessible on my network. I can even access its filesystem via AFP. What I want to know is how the computer could get on my network. My network is secured like this: Does that mean that they've used password cracking tools? The pass is not easy to guess but not hard to figure out via brute-force hacking, I guess. If I am being hacked, should I switch to WPA?

  Read the article

• Backing up an rsnapshot directory to a remote device

  - by user123480

  I have a local backup server that uses rsnapshot with hard links that contains about 10TBs of information which add about 4 to 5GBs per day. It's works great. I've been requested to set up and maintain a remote backup of the local rsnapshot directory structure. It's a nightly backup. I've tried using rsync with encryption which takes forever and eats system resources. A previous post says not to use rsync with hard links for that reason. I need a suggestion of how I can keep the local and remote copies of the rsnapshot structures in sync? Thanks

  Read the article

• How to selectively load device drivers in Windows 7

  - by guillermooo

  I sometimes hook up my laptop to a regular keyboard and mouse set. These require drivers that I don't want loaded when I'm using my laptop's own keyboard and touchpad. So... Can I tell Windows 7 to selectively load one or the other driver based on this condition, or switch between the two?

  Read the article

• Reducing volume of an audio device on windows 7

  - by bdonlan

  I have a USB headset with a very loud amplifier, but low granularity in its gain control. In order to get comfortable audio, I have to reduce the individual application levels in the mixer to '1', and the master mixer to around '10'. Of course, new applications start out at '10', and immediately blast out my ears. Is there a way to add a filter to cut down the volume some so I can get better control of it? That is, reduce the volume of '100' so I can work within a reasonable range.

  Read the article

• Connecting to network device behind NAT from local LAN using the external port and IP

  - by lumbric

  I noticed at several different LANs connected to the Internet through a NAT the following phenomena. There is a server in the LAN and there is a port forwarding to reach this server also from outside the LAN through the NAT. E.g. consider a LAN with the address 192.168.0.* and a SSH server at 192.168.0.2 with port 22 and a forwarding from port 2222 at the NAT 192.168.0.1 to 192.168.0.2:22. If the NAT's external IP is 44.33.22.11, one can connect to the SSH server through 44.33.22.11:2222. Surprisingly this works only from outside the LAN. If one tries to connect to 44.33.22.11:2222 from behind the NAT, there is no answer. Of course one could simply use 192.168.0.2:22, but often it is simpler to use the external IP. The typical use case for me is the configuration on a laptop computer. Usually the user uses any arbitrary Internet connection to connect to his home or office server, but sometimes he will use also the LAN to connect to it and it would be annoying to have to different configurations or bookmarks. Why does it fail to connect from inside the LAN? Is there any good work around?

  Read the article

• windows server 2012 wont boot after instlling on iscsi device

  - by Nandan

  Windows server 2012 installed on a ISCI LUN. Problem noticed after first reboot. Windows boots only if setup DVD is present(i have to ignore "press any key to boot from DVD" prompt). to present the login Screen and everything looks great from here. But the server wont boot without the help of setup DVD. Can any one help me understand what would be the problem? Dell Workstation T3600 Intel Pro NIC (Capable of ISCI Boot and also enabled)

  Read the article

• Trobleshooting input device detection in Windows Xp Pro Sp3

  - by iceman

  My laptop (Acer travelmate 4152NlCi)doesn't respond to the keyboard and mouse anymore while booting in Windows Xp Pro Sp3. i can't type the password and login. I have Opensuse 11.0 on it as well and it works. So I can boot into Linux and not Windows, not even in safe mode. What would be the troubleshooting steps?

  Read the article

• Cannot play sound: device being used by another application

  - by Ecom Evolution

  I tried to change my speaker setup and every time I click "test" I get this error message on Windows 7 SP1. I tried running "sndvol" to view the applications list but the list is empty. Since I tried to test the new speaker setup, I'm now left without sound for all applications and can't get sound even if I switch back. I have not updated my sound drivers so I don't know what could have changed. What could be causing this?

  Read the article

• Syncing 1TB+ to a iSCSI device, software needed

  - by mojah

  Hi, I need to sync a local disk to a iSCSI mount on Windows (server 2003), and I'm struggling to find software that's capable of doing so in a reasonable timeframe. Notes on the current 1TB disk: - 800GB currently in use - Contains a folder with several hundred thousand subfolders, which in turn have several thousand files, ... So I'm trying to find a piece of software that can handle such large filelists, and give me a good timeframe on when this will be copied. I've tried DeltaCopy (the rSync GUI client for Windows), but it's intolerably slow and doesn't provide me with a good estimate time remaining. DeltaCopy: http://www.aboutmyip.com/AboutMyXApp/DeltaCopy.jsp Does anyone know alternative software for Windows, that would do this well?

  Read the article

• Two distinct mount points with one device

  - by user1761555

  After being disappointed with Ubuntu's release update feature, I finally decided to have separate mount points for / and /home. Towards this, I reformatted my HDD giving most of my drive to sda1(meant to be /home) and allocated about 40GB to rootfs (/). Unfortunately, I would also like to have a /projects which is to be located on sda1. Currently, sda1 is being mounted as /dev/sda1 on /home type ext4 (rw) I've tried looking online for a solution to this problem..however, I'm not sure as to what to look for! Is it possible to mount the 'home' directory of sda1 as /home and 'projects' directory of sda1 as /projects?

  Read the article

• Internet connection resets (wifi), no device has wifi for moment

  - by Gizmo

  I have a few devices setup and I noticed this happens with both my old and new router (two different vendors&models) This happens occasionally, and I tried wireshark today and this cought my attention: No. Time Source Destination Protocol Length Info 69 6.464423000 LiteonTe_7f:64:30 Broadcast ARP 42 Who has 192.168.2.4? Tell 0.0.0.0 73 7.451146000 LiteonTe_59:65:94 Arcadyan_e1:8c:cf ARP 42 Who has 192.168.2.254? Tell 192.168.2.1 85 9.450443000 LiteonTe_59:65:94 Arcadyan_e1:8c:cf ARP 42 Who has 192.168.2.254? Tell 192.168.2.1 91 10.521000000 LiteonTe_59:65:94 Broadcast ARP 42 Who has 192.168.2.254? Tell 192.168.2.1 93 10.860953000 LiteonTe_7f:64:30 Broadcast ARP 42 Who has 192.168.2.254? Tell 192.168.2.4 97 11.099463000 LiteonTe_7f:64:30 Broadcast ARP 42 Who has 192.168.2.254? Tell 192.168.2.4 where 192.168.2.254 is the gateway/router, 192.168.2.1 my laptop ip and 192.168.2.4 my sisters laptop.. what's happening here?

  Read the article

< Previous Page | 56 57 58 59 60 61 62 63 64 65 66 67  | Next Page >