Search Results

Search found 23265 results on 931 pages for 'justin case'.

Page 648/931 | < Previous Page | 644 645 646 647 648 649 650 651 652 653 654 655  | Next Page >

• How do I easily repair a single unreadable block on a Linux disk?

  - by Nelson

  My Linux system has started throwing SMART errors in the syslog. I tracked it down and believe the problem is a single block on the disk. How do I go about easily getting the disk to reallocate that one block? I'd like to know what file got destroyed in the process. (I'm aware that if one block fails on a disk others are likely to follow; I have a good ongoing backup and just want to try to keep this disk working.) Searching the web leads to the Bad block HOWTO, which describes a manual process on an unmounted disk. It seems complicated and error-prone. Is there a tool to automate this process in Linux? My only other option is the manufacturer's diagnostic tool, but I presume that'll clobber the bad block without any reporting on what got destroyed. Worst case, it might be filesystem metadata. The disk in question is the primary system partition. Using ext3fs and LVM. Here's the error log from syslog and the relevant bit from smartctl. smartd[5226]: Device: /dev/hda, 1 Currently unreadable (pending) sectors Error 1 occurred at disk power-on lifetime: 17449 hours (727 days + 1 hours) ... Error: UNC at LBA = 0x00d39eee = 13868782 There's a full smartctl dump on pastebin.

  Read the article

• PXE booting LACP hosts on Force10 S50N with FTOS

  - by lolwutreddit

  Hardware: S50N Firmware: FTOS 8.4.2.6 Problem: We're trying to PXE boot some servers that are connected via port-channel interfaces with LACP. Current Work-around: we PXE boot a server with a single interface (eth0), and then use a Perl script to turn up the port-channel interfaces after the server is built. Details: Is anyone doing anything similar on Force10 S50 switches with FTOS? If not, is anyone doing this on another S series, or larger chassis-based Force10? I'm wondering if Native VLAN will solve this, since ports in a port-channel cannot explicitly have a VLAN set, and they don't seem to use the tagged or untagged VLAN that the port channel is in. I will confirm this next (I think it's the only thing I haven't tried) Juniper Example: http://broken.net/openindiana/how-to-pxe-boot-systems-on-lacp-using-juniper-switches/ Cisco: there are plenty of documented ways to solve this issue on IOS and Nexus Update/Edit: since there seems to be no way to use interface or port-channel mode commands to get the individual interfaces to show up in spanning-tree (rtsp in this case), the ports should never go into a forwarding state. I'm not going to mess with it anymore unless a) someone that has experience passes it on, or b) Force10 comes up with a solution for this (I'm guessing it will only be introduced on other S platforms (S55, S60), since the S50 seems to be near EOL). I'm basing that on the fact that the Open Automation type features are only being supported on the newer switches.

  Read the article

• nginx does not use variables set in /etc/environment on system reboot, but does when restarted from shell

  - by Dave Nolan

  I have a Rails app running on nginx/passenger. It restarts happily in a shell using sudo /etc/init.d/nginx stop|start|restart. But Passenger throws an error when the system is rebooted: "Missing the Rails #{version} gem". But GEM_HOME and GEM_PATH are both set in /etc/environment so surely they would be available to all processes during reboot? /etc/environment PATH="/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin:/usr/bin/X11:/usr/games" GEM_HOME=/var/lib/gems/1.8 GEM_PATH=/var/lib/gems/1.8 /etc/init.d/nginx #! /bin/sh ### BEGIN INIT INFO # Provides: nginx # Required-Start: $all # Required-Stop: $all # Default-Start: 2 3 4 5 # Default-Stop: 0 1 6 # Short-Description: starts the nginx web server # Description: starts nginx using start-stop-daemon ### END INIT INFO PATH=/usr/local/sbin:/usr/local/bin:/sbin:/bin:/usr/sbin:/usr/bin DAEMON=/opt/nginx/sbin/nginx NAME=nginx DESC=nginx test -x $DAEMON || exit 0 # Include nginx defaults if available if [ -f /etc/default/nginx ] ; then . /etc/default/nginx fi set -e case "$1" in start) echo -n "Starting $DESC: " start-stop-daemon --start --quiet --pidfile /var/log/nginx/$NAME.pid \ --exec $DAEMON -- $DAEMON_OPTS echo "$NAME." ;; stop) echo -n "Stopping $DESC: " start-stop-daemon --stop --quiet --pidfile /var/log/nginx/$NAME.pid \ --exec $DAEMON echo "$NAME." ;; restart|force-reload) echo -n "Restarting $DESC: " start-stop-daemon --stop --quiet --pidfile \ /var/log/nginx/$NAME.pid --exec $DAEMON sleep 1 start-stop-daemon --start --quiet --pidfile \ /var/log/nginx/$NAME.pid --exec $DAEMON -- $DAEMON_OPTS echo "$NAME." ;; reload) echo -n "Reloading $DESC configuration: " start-stop-daemon --stop --signal HUP --quiet --pidfile /var/log/nginx/$NAME.pid \ --exec $DAEMON echo "$NAME." ;; *) N=/etc/init.d/$NAME echo "Usage: $N {start|stop|restart|force-reload}" >&2 exit 1 ;; esac exit 0 $ opt/nginx/sbin/nginx -v nginx version: nginx/0.7.67 Ubuntu lucid

  Read the article

• 0x0000007b WinXP in VirtualBox with no Admin access on source drive

  - by Ozzah

  I have a physical drive with an installation of WinXP-32 which I have made a clone of using SysInternals disk2vhd. I have no admin rights on this installation. I have tried to boot this VHD in VirtualBox, however it blue screens on 0x0000007b. I have researched this and apparently the cause is that Windows doesn't like the IDE controller changing. I have tried all the available controllers in VirtualBox, but they all produce the same result. There is a Microsoft KB article which describes a method involving loading a .reg file and extracting some sys files from a CAB. This method apparently works well for many people with this problem, however it will not work for me as I don't have admin rights on the WinXP installation. Is there anything I can do in this case? Is there any way of loading the .reg file outside the OS? or perhaps doing a repair using the WinXP CD? Even though I have no admin rights on the source drive installation of Windows, I do obviously have full access to the file system directly on the drive and also in the VHD itself.

  Read the article

• Replace text with spaces in MySQL

  - by javipas

  I'm trying to do a global replace of search in my database, which has a lot of articles with a double carriage return because of this code: <p> </p> I'd like to replace this in my WordPress blog so instead of that appears... nothing, and so I can delete the CR. I've tried this on my database UPDATE wp_posts set post_content = replace (post_content,'<p> </p>',''); but didn't work. Why? Do I have to add special thinks to consider the space between the <p>and the</p>? Mmm. Good points, both Jon Angliss and Wim. Jon, as you could have guessed, the database shows no entries with that text string. So there's something going on inside the post_content field. Wim, the famous   was replaced previously, but there are still hundreds of posts that for some reason have something different between the p and the /p tags. I've done a search of one of the posts with this error: mysql> select * from wp_posts where post_title like '%3DVisionLive%'; And looking in the wp_content field, this is a little piece of the post: Phil Eisler, responsable de la divisi?n 3D Vision.?</p> <p>?</p> <p>Este portal ser? por tanto No spanish tilde (accent) shown on the terminal, and instead of an space there's a quotation mark between the p and the /p tags. I've tried to replace <p>?</p>, but again, no results. There's some character (or several) there, but I don't know how to discover that. Maybe it's the character set of my terminal, but I've accessed the database from phpmyadmin and in that case there's a space character between the p and the /p. Weird.

  Read the article

• 500 Internal Server Error after changing .NET Framework Version to 4.0 in IIS7

  - by René

  I just changed my .NET Framework Version of the Application Pools in IIS7 Manager, following these instructions. Now when I try to re-upload my ASP.Net page, it shows me a 500 - Internal server error. I have tried uploading it in .net 2.0(X86, X64, AnyCPU), and 4.0(X86, X64, AnyCPU), and everything gives the same error. This is all the details the error gives me: "There is a problem with the resource you are looking for, and it cannot be displayed." When keeping the .NET version on 2.0 on the server, it works just fine. Also, when uploading "index.htm", it works fine as well, it just shows the HTML page. This is on Windows Server 2008 R2, by the way. EDIT: I have finally found out how to get the error details. Here they are: "Handler "PageHandlerFactory-Integrated" has a bad module "ManagedPipelineHandler" in its module list." "Most likely causes: •Managed handler is used; however, ASP.NET is not installed or is not installed completely. •There is a typographical error in the configuration for the handler module list. Things you can try: •Install ASP.NET if you are using managed handler. •Ensure that the handler module's name is specified correctly. Module names are case-sensitive and use the format modules="StaticFileModule,DefaultDocumentModule,DirectoryListingModule"." I am sure that I have installed ASP.NET completely. Please help me, -René

  Read the article

• How to disable 3rd party cookies in Chrome?

  - by David Nordvall

  I have both the "stop websites from storing local data" and the "block all third party cookies without exception" settings enabled in Chrome 12 (I'm not sure what the exact names of these settings are in english as I run Chrome with swedish localization). I do however have two problems. My first problem is that when I'm visiting one of my local news paper's site (and surely other), cookies from www.facebook.com is allowed for some reason. I suspect that the reason is that I have added an exception to the www.facebook.com domain but as the setting "block all third party cookies without exception" implies, that shouldn't matter. My second problem is that if I check what cookies are stored on my computer after browsing for a while, I have tons of cookies that are not on my white list. Primarily from ad services. My expectations from enabling the above mentioned settings was that only cookies that fulfill the two folling requirements would be accepted: the cookies must be from the domain in my address bar the cookies must be from a domain on my whitelist Apparently this isn't the case. The question is, have I completely misunderstood the settings or is this a bug? And, either way, is there a way to accomplish my desired behavior?

  Read the article

• Commandline program to extract archives with automatic subdirectry detection

  - by ??????

  The title already says it. What I'm looking for is essentially the pure commandline counterpart to ark -ba <path> (on KDE), or file-roller -h <path> (on GNOME/Unity). Unfortunately, both ark and file-roller require X to be running. I'm aware that it is relatively simple to write a tool that detects archives based on their file extension, and then runs the appropiate program: #!/bin/bash if [[ -f "$1" ]] ; then case $1 in *.tar.bz2) tar xjvf $1 ;; *.tar.gz) tar xzvf $1 ;; *.bz2) bunzip2 $1 ;; *.rar) rar x $1 ;; *.gz) gunzip $1 ;; *.tar) tar xf $1 ;; *.tbz2) tar xjvf $1 ;; *.tgz) tar xzvf $1 ;; *.zip) unzip $1 ;; *.Z) uncompress $1 ;; *.7z) 7z x $1 ;; *) echo "'$1' cannot be extracted with this utility" ;; esac else echo "path '$1' does not exist or is not a file" fi However, that doesn't take care of subdirectory detection (and in fact, many extraction programs do not even supply such an option). So might there be a program that does exactly that? I wasn't sure whether or not to ask on askubuntu.com, because this question isn't really about Ubuntu, but rather about any Linux operating system. My apologies if this question does not fit in here.

  Read the article

• ZFS - Impact of L2ARC cache device failure (Nexenta)

  - by ewwhite

  I have an HP ProLiant DL380 G7 server running as a NexentaStor storage unit. The server has 36GB RAM, 2 LSI 9211-8i SAS controllers (no SAS expanders), 2 SAS system drives, 12 SAS data drives, a hot-spare disk, an Intel X25-M L2ARC cache and a DDRdrive PCI ZIL accelerator. This system serves NFS to multiple VMWare hosts. I also have about 90-100GB of deduplicated data on the array. I've had two incidents where performance tanked suddenly, leaving the VM guests and Nexenta SSH/Web consoles inaccessible and requiring a full reboot of the array to restore functionality. In both cases, it was the Intel X-25M L2ARC SSD that failed or was "offlined". NexentaStor failed to alert me on the cache failure, however the general ZFS FMA alert was visible on the (unresponsive) console screen. The zpool status output showed: pool: vol1 state: ONLINE scan: scrub repaired 0 in 0h57m with 0 errors on Sat May 21 05:57:27 2011 config: NAME STATE READ WRITE CKSUM vol1 ONLINE 0 0 0 mirror-0 ONLINE 0 0 0 c8t5000C50031B94409d0 ONLINE 0 0 0 c9t5000C50031BBFE25d0 ONLINE 0 0 0 mirror-1 ONLINE 0 0 0 c10t5000C50031D158FDd0 ONLINE 0 0 0 c11t5000C5002C823045d0 ONLINE 0 0 0 mirror-2 ONLINE 0 0 0 c12t5000C50031D91AD1d0 ONLINE 0 0 0 c2t5000C50031D911B9d0 ONLINE 0 0 0 mirror-3 ONLINE 0 0 0 c13t5000C50031BC293Dd0 ONLINE 0 0 0 c14t5000C50031BD208Dd0 ONLINE 0 0 0 mirror-4 ONLINE 0 0 0 c15t5000C50031BBF6F5d0 ONLINE 0 0 0 c16t5000C50031D8CFADd0 ONLINE 0 0 0 mirror-5 ONLINE 0 0 0 c17t5000C50031BC0E01d0 ONLINE 0 0 0 c18t5000C5002C7CCE41d0 ONLINE 0 0 0 logs c19t0d0 ONLINE 0 0 0 cache c6t5001517959467B45d0 FAULTED 2 542 0 too many errors spares c7t5000C50031CB43D9d0 AVAIL errors: No known data errors This did not trigger any alerts from within Nexenta. I was under the impression that an L2ARC failure would not impact the system. But in this case, it surely was the culprit. I've never seen any recommendations to RAID L2ARC. Removing the bad SSD entirely from the server got me back running, but I'm concerned about the impact of the device failure (and maybe the lack of notification from NexentaStor as well). Edit - What's the current best-choice SSD for L2ARC cache applications these days?

  Read the article

• Created new torrent but client unable to find seeds

  - by ehfeng

  I tried creating a new torrent, using uTorrent, following the directions from torrentfreak (http://torrentfreak.com/how-to-create-a-torrent/). I used a bunch of trackers (just in case any individual one was having troubles) and uTorrent shows it as "seeding" with 100% of the file. It shows: seeds 0(1), peers 0(0). http://exodus.desync.com/announce http://eztv.tracker.prq.to/announce http://open.tracker.thepiratebay.org/announce http://www.torrent-downloads.to:2710/announce http://denis.stalker.h3q.com:6969/announce udp://denis.stalker.h3q.com:6969/announce http://www.sumotracker.com/announce I've also attempted to remove the torrent and then re-add the torrent, pointing it to my already existing files, forcing uTorrent to recheck the files and then begin seeding. Yet when I share the .torrent file with my other computer and attempt to download, it is unable to find any peers or seeds. To confirm that both clients are working, I downloaded a torrent on both computers, using their respective clients, using torrents I found on isohunt. This tells me that there must be something wrong in how I'm creating my torrents. Any help is appreciated.

  Read the article

• ASUS P8B WS - Endless Reboots

  - by tuxGurl

  I am running a Intel XEON 1245 with 4GBx2 Kingston Memory ECC Unbuffered DDR3 on an ASUS P8B WS motherboard. BIOS Version 0904 x64. This system is a little over a month old. It is running Ubuntu 11.10. This evening I found the machine turned off. When I tried to restart it, it would POST and stop at the GRUB screen. When I selected Ubuntu and hit enter within 2-3 seconds the would shutdown and restart. If I stayed at the GRUB screen and did nothing the system would not cut out. I tried booting off a USB stick and again 2-3 seconds after selecting 'Try Ubuntu without Installing' the machine will cut power and reboot. Things I have tried so far: Resetting the BIOS using the on board jumper Resetting the BIOS settings to default Disconnecting all external hardware - except keyboard & monitor Booting with 1 stick of RAM - I tried different single sticks Ensured that onboard EPU and GPU boost switches are in the off position. I am running a Memtest86 right now and it has been running for 38+ minutes. This is not an OS problem or an overheating issue (I have a CoolerMaster HAF Case with 3 fans besides the CPU fan) I am at a loss as to what to try next. I think the BIOS is mis-configured somehow but I don't know what to look for.

  Read the article

• MS SQL Server slows down over time?

  - by Dave Holland

  Have any of you experienced the following, and have you found a solution: A large part of our website's back-end is MS SQL Server 2005. Every week or two weeks the site begins running slower - and I see queries taking longer and longer to complete in SQL. I have a query that I like to use: USE master select text,wait_time,blocking_session_id AS "Block", percent_complete, * from sys.dm_exec_requests CROSS APPLY sys.dm_exec_sql_text(sql_handle) AS s2 order by start_time asc Which is fairly useful... it gives a snapshot of everything that's running right at that moment against your SQL server. What's nice is that even if your CPU is pegged at 100% for some reason and Activity Monitor is refusing to load (I'm sure some of you have been there) this query still returns and you can see what query is killing your DB. When I run this, or Activity Monitor during the times that SQL has begun to slow down I don't see any specific queries causing the issue - they are ALL running slower across the board. If I restart the MS SQL Service then everything is fine, it speeds right up - for a week or two until it happens again. Nothing that I can think of has changed, but this just started a few months ago... Ideas? --Added Please note that when this database slowdown happens it doesn't matter if we are getting 100K page views an hour (busier time of day) or 10K page views an hour (slow time) the queries all take a longer time to complete than normal. The server isn't really under stress - the CPU isn't high, the disk usage doesn't seem to be out of control... it feels like index fragmentation or something of the sort but that doesn't seem to be the case. As far as pasting results of the query I pasted above I really can't do that. The Query above lists the login of the user performing the task, the entire query, etc etc.. and I'd really not like to hand out the names of my databases, tables, columns and the logins online :)... I can tell you that the queries running at that time are normal, standard queries for our site that run all the time, nothing out of the norm.

  Read the article

• How \Deleted flag can be unset for all mails in cyrus-imapd mailbox?

  - by Sachin Divekar

  I have a 5GB mailbox which I moved using imapsync. But somehow I messed up with --delete/--delete2 option and end up with almost all the messages having \Deleted flag set. I do not have delayed expunge enabled, so I can not use unexpunge utility. I am using cyrus-imapd v2.3.7. Using cyrus-imapd's debugging feature I found out that email client(Roundcube in my case) fires following IMAP command to unset it. UID STORE 179 -FLAGS.SILENT (\Deleted) I don't know if somehow I can fire this command for all the mails. Is there any way I can unset \Deleted flag for all the mails in the mailbox? UPDATE: Using @geekosaur's tip of specifying range of message-ids in the above command, I could solve it for one mailbox under INBOX like INBOX.folder1. Is there any way I can do it for multiple mailboxes under INBOX recursively? Now I am working on solving it using/creating some script, maybe using Perl's IMAP related module. But still I need to solve it asap so inputs are welcome.

  Read the article

• sudo ./starling start works well but sudo service starling start fails

  - by Keating Wang

  sudo ./starling start works well but sudo service starling start fails $ sudo ./starling start * Starting Starling Server... [ OK ] $ sudo ./starling stop * Stop Starling Server... [ OK ] $ sudo service starling stop * Starting Starling Server... /home/keating/.rvm/rubies/ruby-1.9.2-p290/lib/ruby/site_ruby/1.9.1/rubygems/dependency.rb:247:in `to_specs': Could not find starling (>= 0) amongst [minitest-1.6.0, rake-0.8.7, rdoc-2.5.8] (Gem::LoadError) from /home/keating/.rvm/rubies/ruby-1.9.2-p290/lib/ruby/site_ruby/1.9.1/rubygems/dependency.rb:256:in `to_spec' from /home/keating/.rvm/rubies/ruby-1.9.2-p290/lib/ruby/site_ruby/1.9.1/rubygems.rb:1229:in `gem' from /home/keating/.rvm/gems/ruby-1.9.2-p290/bin/starling:18:in `<main>' The error above is 'cannot find gem starling' Following the starling file(located in /etc/init.d, rwxrwxrwx): set -e LOGFILE=/var/log/starling/starling.log SPOOLDIR=/var/spool/starling PORT=22122 LISTEN=127.0.0.1 PIDFILE=/var/run/starling.pid NAME=starling DESC="Starling" INSTALL_DIR=/home/keating/.rvm/gems/ruby-1.9.2-p290/bin/ DAEMON=$INSTALL_DIR/$NAME SCRIPTNAME=/etc/init.d/$NAME OPTS="-d" . /lib/lsb/init-functions d_start() { log_begin_msg "Starting Starling Server..." start-stop-daemon --start --quiet --pidfile $PIDFILE --exec $DAEMON -- $OPTS || log_end_msg 1 log_end_msg 0 } d_stop() { log_begin_msg "Stopping Starling Server..." start-stop-daemon --stop --quiet --pidfile $PIDFILE || log_end_msg 1 log_end_msg 0 } case "$1" in start) d_start ;; stop) d_stop ;; restart|force-reload|reload) d_stop sleep 2 d_start ;; *) echo "Usage: $SCRIPTNAME {start|stop|restart|force-reload}" exit 3 ;; esac exit 0

  Read the article

• Networking "chokes" on Windows 7 64 bit

  - by Rohit Nair

  I've been having this problem for some months now, and I have been unable to figure out a solution, or even the cause. At random points throughout the day, my internet connectivity "freezes". I don't get disconnected from my local wireless network. My router doesn't get disconnected from the world. However, for some reason, my computer stops receiving packets. If I'm playing an MMO ( World of Warcraft, in this case, but it has happened with Eve Online as well ) all activity just freezes. If I try to browse, Opera, Firefox and IE all stall at "Waiting for google.com..." or whatever the hostname may be. Inspection with a packet sniffer seems to reveal that there are no incoming packets. Here's the interesting part. Disconnecting from my wireless network and reconnecting fixes the issue. Obviously this led me to conclude that it was a problem with my router or wireless card. However, I have tweaked all the settings on my router that I could think of, including things like QoS, AP Isolation, etc. with no change. My wireless card doesn't really have that many options, and I have uninstalled and reinstalled drivers a few times without any change. Windows Firewall on/off doesn't make a difference. Anyone have any suggestions for debugging this? It's becoming an annoyance.

  Read the article

• external drive enclosure -> software RAID 5?

  - by memilanuk

  Hello all, I have two older PCs on my LAN posing as 'servers'... one running FreeNAS off a USB stick using three 500GB hdds in a ZFS RAID-Z pool serving as storage for the LAN and one running Debian Lenny with an 80GB drive used as a general purpose 'tinker' box that I can ssh into, etc. Problem is that the SMART report for one of those 500GB drives in the FreeNAS box is showing some pre-failure attributes, and the whole array is a little small anyways. Rather than simply replace one 500GB drive with another 500GB drive, and have no backup of the file server, I'd like to upgrade all the drives to 2TB ones - but I have no where to store that much data in the mean while. As such, I started looking at getting a 4-bay external drive enclosure with an eSATA card for the Debian box, with the hopes of creating a RAID5 + LVM setup using those drives and backing the data up to that external drive enclosure. After the backup is done, replace the drives in the FreeNAS box and rebuild the array there and mirror the data back. Then, I'd have both the primary storage (on the FreeNAS box) and a backup (which I don't have currently) using the external drive enclosure on the Debian box. My big question is... most of these external drive boxes seem to claim support for JBOD, RAID 0, 1, 10, 5, etc. - should I presume that is simply fake RAID like many commodity mobos have, and not really usable in Linux? In that case, with all the drives hanging off the one eSATA connection, will Linux (specifically Debian Squeeze, as I plan on upgrading that box here shortly) see all four drives, or just the first one? Will I be able to configure them in a RAID5 array as desired? Thanks, Monte

  Read the article

• Raid-1 Western Digital Green AARS, cloning and WD Align Utility

  - by Jaguar

  Hello all, My current setup runs on top of 2x Western Digital 2500KS drives on Raid-1, using the motherboard's 780G raid controller, on WinXP. Everything is fine, but the drives are a bit noisy. I am considering buying 2x WD6400AARS disks which are the 640GB slower 'green' drives, but also feature the Advanced Formatting 4KB sectors. This means that for WinXP the partition will have to be aligned to work properly, else there is a performance penalty. There are 2 questions here: The Green drives from WD are all slower and are (according to WD) susceptible to drop-out's from the controller. Has anyone any experience in this matter? Is there a possibility the controller will drop a drive? If so, can i do anything about it? Secondly, western digital gives a utility to perform the alignment on the partition. The thing is, will the utility see the drives in question as the operating system only sees 1 logical disk? I will be making the transition using a cloning tool (most probably norton ghost) unless i don't find a solution or a clear answer, in which case i'll just buy a win 7 license and make a clean install... thx in advance

  Read the article

• Run script before shutdown/restart

  - by dtbarne

  I'd like to run a PHP script when an instance is told to shutdown, but of course before it actually finishes shutting down. My particular script is just looking to push some log files from the local partition to a another server. I've got the gist of how this process works, but I need some clarification. How I understand it. Please correct me if I'm wrong. Create an executable script in /etc/init.d (lets call it /etc/init.d/push-logs) Create a symlink to /etc/init.d/push-logs from /etc/rc0.d (shutdown) and /etc/rc6.d (reboot). The name should be KXXpush-logs Here's my questions: Of course - am I understanding correctly? For #2 above - it sounds like the lower the XX the better - is there too low a number I can use? Does it matter if it shares a number with another script? Does the script in /etc/init.d/push-logs HAVE to follow the standard init.d template (supporting start/stop, etc. commands)? This doesn't really apply to my use case. If possible I just want the script to be the following: #!/bin/sh # # Run PHP file prior to shutdown # /usr/bin/php /path/to/php_file.php

  Read the article

• How to setup a virtual host in Ubuntu?

  - by Rade

  I have an app that's accessible via 1.2.3.4/myapp. The app is installed in /var/www/myapp. I've set up a subdomain(apps.mydomain.com) that points to 1.2.3.4. I want the server to point to var/www/myapp if I type apps.mydomain.com/myapp, how do I do that? I have experience creating virtual hosts(lots of them) locally but I'm lost because it's now in production and it's a little different. Here's my virtual host config: <VirtualHost *:80> ServerAdmin webmaster@localhost ServerName apps.mydomain.com/myapp DocumentRoot /var/www/myapp/public <Directory /> Options FollowSymLinks AllowOverride All </Directory> <Directory /var/www/> Options Indexes FollowSymLinks MultiViews AllowOverride All Order allow,deny allow from all </Directory> ScriptAlias /cgi-bin/ /usr/lib/cgi-bin/ <Directory "/usr/lib/cgi-bin"> AllowOverride All Options +ExecCGI -MultiViews +SymLinksIfOwnerMatch Order allow,deny Allow from all </Directory> ErrorLog ${APACHE_LOG_DIR}/error.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel warn CustomLog ${APACHE_LOG_DIR}/access.log combined </VirtualHost> Any idea why I still see the files instead of pointing me to the document root? Just in case someone might ask, the app is based on Laravel 4 framework. It's really bad right now because anyone can access the files from the browser.

  Read the article

• Ati X1600 driver problem on Mac

  - by Mulot

  Hi all, I currently own a 06' Macbook pro 1.1, and since some months I have recurrent problems of displays bug or artifacts. I searched quickly around to see that a lot of other users on Mac (iMac or Macbook pro) also have the same problem due to a problem for the X1600 video card. Apparently it's due to overheating problem, in my case even without warming a lot I have very bad display bugs such as colorful pixel lines, or glitches, and freeze and crash, all of this on Tiger, Leopard and Snow Leopard. I found this interesting article here talking about this problem and trying to gather people so that Apple take the serious GPU problem in consideration. In one of the comments, an user said he removed all bundle named with "radeon" and then he had no more problems under Leopard, and seems ot work fine well too on Snow Leopard. I did the same thing, I removed the bundles of the driver, restart, and no more problems, but not more 3D acceleration, which is not an acceptable solution. For those interested, here is the list of files to be deleted to stop having this problem. /System/Library/Extensions/ATIRadeonX1000.kext /System/Library/Extensions/ATIRadeonX1000GA.plugin /System/Library/Extensions/ATIRadeonX1000GLDriver.bundle /System/Library/Extensions/ATIRadeonX1000VADriver.bundle /System/Library/Extensions/ATIRadeonX2000.kext /System/Library/Extensions/ATIRadeonX2000GA.plugin /System/Library/Extensions/ATIRadeonX2000GLDriver.bundle /System/Library/Extensions/ATIRadeonX2000VADriver.bundle I would like to know if there is a way to fix this using other drivers if that's possible or by creating a group to force Apple to make a replacement program in place. Edit : How to locate those files on your hard drive if you are not under Snow Tiger : sudo find / -iname "*radeon*"

  Read the article

• Cant connect to MySQL server from Java application

  - by RN

  This is on VPS\Centos server. The MySQL server is pre configured. I am running the Java application on Tomcat My Java web application is not able to connect to the MySQL server. I get an error - "Caused by: java.net.ConnectException: Connection refused" I suspect this to be a configuration problem rather than a coding problem- hence I have posted this on ServerFault And yes, The same web-app is able to connect to MySQL on a different linux box This is the URL that I provided to my Java application (note- it assumes default port) url = "jdbc:mysql://localhost/pickupgames" My first suspicion was that I am running on a non-default port So I tried to find the port where mySQL server is running I tried every trick mentioned in http://serverfault.com/questions/116100/how-to-check-what-port-mysql-is-running-on But no luck ! SHOW GLOBAL VARIABLES LIKE 'PORT'; This shows port 0 netstat -tlnp doesn't show mysql at all /etc/my.cnf It has no port entry telnet localhost 3306 Doesn't connect And in case you are wondering if mysql server is running at all or not It is And I know for sure, because I have been able to login using the mysql command Also # ps -ef|grep 'mysql' root 31839 27662 0 00:49 pts/3 00:00:00 grep mysql root 32452 1 0 Apr02 ? 00:00:00 /bin/sh /usr/bin/mysqld_safe --skip-grant-tables --skip-networking mysql 32504 32452 0 Apr02 ? 00:00:06 /usr/libexec/mysqld --basedir=/usr --datadir=/var/lib/mysql --user=mysql --pid-file=/var/run/mysqld/mysqld.pid --skip-external-locking --socket=/var/lib/mysql/mysql.sock --skip-grant-tables --skip-networking Please note the --skip-networking parameter Does this have something to do with the issue ? Any explanation why I cant connect to mysql server on port 3306 by telnet? Or why it docent show up under netstat? Any suggestion on whet I should try next ?

  Read the article

• Bash Script - Traffic Shaping

  - by Craig-Aaron

  hey all, I was wondering if you could have a look at my script and help me add a few things to it, How do I get it to find how many active ethernet ports I have? and how do I filter more than 1 ethernet port How I get this to do a range of IP address? Once I have a few ethenet ports I need to add traffic control to each one #!/bin/bash # Name of the traffic control command. TC=/sbin/tc # The network interface we're planning on limiting bandwidth. IF=eth0 # Network card interface # Download limit (in mega bits) DNLD=10mbit # DOWNLOAD Limit # Upload limit (in mega bits) UPLD=1mbit # UPLOAD Limit # IP address range of the machine we are controlling IP=192.168.0.1 # Host IP # Filter options for limiting the intended interface. U32="$TC filter add dev $IF protocol ip parent 1:0 prio 1 u32" start() { # Hierarchical Token Bucket (HTB) to shape bandwidth $TC qdisc add dev $IF root handle 1: htb default 30 #Creates the root schedlar $TC class add dev $IF parent 1: classid 1:1 htb rate $DNLD #Creates a child schedlar to shape download $TC class add dev $IF parent 1: classid 1:2 htb rate $UPLD #Creates a child schedlar to shape upload $U32 match ip dst $IP/24 flowid 1:1 #Filter to match the interface, limit download speed $U32 match ip src $IP/24 flowid 1:2 #Filter to match the interface, limit upload speed } stop() { # Stop the bandwidth shaping. $TC qdisc del dev $IF root } restart() { # Self-explanatory. stop sleep 1 start } show() { # Display status of traffic control status. $TC -s qdisc ls dev $IF } case "$1" in start) echo -n "Starting bandwidth shaping: " start echo "done" ;; stop) echo -n "Stopping bandwidth shaping: " stop echo "done" ;; restart) echo -n "Restarting bandwidth shaping: " restart echo "done" ;; show) echo "Bandwidth shaping status for $IF:" show echo "" ;; *) pwd=$(pwd) echo "Usage: tc.bash {start|stop|restart|show}" ;; esac exit 0 thanks

  Read the article

• Add bookmarks to Delicious and Google Bookmarks at the same time

  - by BrianH

  I have used delicious.com (or back then, del.icio.us) to store my bookmarks for a long time now, and I love it. I was looking through some of my Google services, and realized they have a bookmarking service that integrates with your Google searches (I thought they had a bookmarking service before, but it went away? Maybe not). I like delicious just fine - I'm not interested in leaving. But I also like how my Google bookmarks are highlighted (and I'm guessing, brought to the top) in my search results so I can easily tell if I've bookmarked a site (kind of like the "promote up" feature). I can't even count the number of times I search for a site only to find I've been there months or years ago. If sites I've bookmarked in the past are highlighted in my search results, it makes it easier to pick which search result to go to. My question is around bookmarking tools: Is there a bookmarklet or Firefox addon that will let me save a bookmark to multiple services at the same time, in this case, Google and Delicious? Or maybe a service to sync my delicious bookmarks to Google bookmarks on a regular basis? I have used the Delicious addon since the beginning - it would just be nice to add a bookmark to multiple services with 1 addon. For that matter, it would be nice to add Evernote into the mix - click 1 button to save the page to Evernote, and bookmark the page in Google and delicious. EDIT on 7/30/2009 - Summary: A proposed solution is to use the Delicious addon and the GMarks addon to keep the 2 services in sync. I was not able to get the 2 addons to keep everything in sync, so it was also suggest to use the Google Toolbar with the Delicious addon to keep everything in sync. I personally have reservations with letting Google know about every single site I visit, I believe this solution will work, so I am accepting it as the answer. I still wish there was a solution that would let you post a bookmark/page to multiple services at the same time (delicious, google, evernote, digg, diigo, etc.). Thanks!

  Read the article

• How to fix a Postfix/MySQL/Dovecot Unknown Host Issue?

  - by thiesdiggity

  I am having an issue with one of my Postfix/Dovecot mail servers and I'm unsure how to fix the problem. I will try to explain it in detail, here it goes: I have an Ubuntu server setup using Virtual hosting with Postfix, Dovecot and MySQL. We have one domain setup as a virtual domain, for this example I am going to use mail.example.com. Under that domain we have one email address. I have another server (MS Exchange) setup using another one of my sub-domains, ex.example.com. The problem is that when I SMTP into the account on mail.example.com and try to send an email to an account on ex.example.com, I get the email returned back to us with an "unknown host" error. Now, I know that the mail.example.com server can resolve the ex.example.com domain because I can ping/dig while SSH'd into it. I can also log into Postfix via Telnet and send an email to an ex.example.com mailbox. I'm guessing that it has something to do with Postfix/Dovecot looking locally for the domain in the virtual domain list because of the tld domain (example.com)? If that's the case, how do I get Postfix/Dovecot to only look locally for the entire URL (mail.example.com) and if it doesn't find it, send it to the correct server by looking up the MX/A records (which I know exist and are setup correctly)? I have been working on this all day and any guidance would be GREATLY appreciated! Thanks for your time!

  Read the article

• VMware Workstation update stopped autofit guest working

  - by u8sand

  VMware one day offered an update (8.0.1 build-528992 my current version) from 8.0. I accepted it, because updates usually fix problems. However not in this case... Previously it worked very well. Now, it still "works" but the one glitch I'm getting makes it too hard to deal with. This screenshot will explain my problem: As you can see, my virtual PC is not resizing correctly. (This happens with any operating system), autofit guest just doesn't work - it only results in things like this happening. Thanks to the tools it becomes very hard to NOT autofit guest. I've tried uninstalling 8.0.1 completely and installing 8.0 again but with the same results. I don't really understand what the new update has done to VMware Workstation or to my virtual machines. I do believe this isn't VMware Workstation's direct fault but from VMware Tools, which would explain why going back to 8.0 didn't work since VMware tools has its own updates. How can I fix this? The host is running Windows 7 Ultimate 64-bit.

  Read the article

< Previous Page | 644 645 646 647 648 649 650 651 652 653 654 655  | Next Page >