Search Results

Search found 1898 results on 76 pages for 'gnu coreutils'.

Page 73/76 | < Previous Page | 69 70 71 72 73 74 75 76  | Next Page >

• Linux policy routing - packets not coming back

  - by Bugsik

  i am trying to set up policy routing on my home server. My network looks like this: Host routed VPN gateway Internet link through VPN 192.168.0.35/24 ---> 192.168.0.5/24 ---> 192.168.0.1 DSL router 10.200.2.235/22 .... .... 10.200.0.1 VPN server The traffic from 192.168.0.32/27 should be and is routed through VPN. I wanted to define some routing policies to route some traffic from 192.168.0.5 through VPN as well - for start - from user with uid 2000. Policy routing is done using iptables mark target and ip rule fwmark. The problem: When connecting using user 2000 from 192.168.0.5 tcpdump shows outgoing packets, but nothing comes back. Traffic from 192.168.0.35 works fine (here I am not using fwmark but src policy). Here is my VPN gateway setup: # uname -a Linux placebo 3.2.0-34-generic #53-Ubuntu SMP Thu Nov 15 10:49:02 UTC 2012 i686 i686 i386 GNU/Linux # iptables -V iptables v1.4.12 # ip -V ip utility, iproute2-ss111117 IPtables rules (all policies in table filter are ACCEPT) # iptables -t mangle -nvL Chain PREROUTING (policy ACCEPT 770K packets, 314M bytes) pkts bytes target prot opt in out source destination Chain INPUT (policy ACCEPT 767K packets, 312M bytes) pkts bytes target prot opt in out source destination Chain FORWARD (policy ACCEPT 5520 packets, 1920K bytes) pkts bytes target prot opt in out source destination Chain OUTPUT (policy ACCEPT 782K packets, 901M bytes) pkts bytes target prot opt in out source destination 74 4707 MARK all -- * * 0.0.0.0/0 0.0.0.0/0 owner UID match 2000 MARK set 0x3 Chain POSTROUTING (policy ACCEPT 788K packets, 903M bytes) pkts bytes target prot opt in out source destination # iptables -t nat -nvL Chain PREROUTING (policy ACCEPT 996 packets, 51172 bytes) pkts bytes target prot opt in out source destination Chain INPUT (policy ACCEPT 7 packets, 432 bytes) pkts bytes target prot opt in out source destination Chain OUTPUT (policy ACCEPT 1364 packets, 112K bytes) pkts bytes target prot opt in out source destination Chain POSTROUTING (policy ACCEPT 2302 packets, 160K bytes) pkts bytes target prot opt in out source destination 119 7588 MASQUERADE all -- * vpn 0.0.0.0/0 0.0.0.0/0 Routing: # ip addr show 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth0: <BROADCAST,MULTICAST,PROMISC,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast master lan state UNKNOWN qlen 1000 link/ether 00:40:63:f9:c3:8f brd ff:ff:ff:ff:ff:ff valid_lft forever preferred_lft forever 3: lan: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP link/ether 00:40:63:f9:c3:8f brd ff:ff:ff:ff:ff:ff inet 192.168.0.5/24 brd 192.168.0.255 scope global lan inet6 fe80::240:63ff:fef9:c38f/64 scope link valid_lft forever preferred_lft forever 4: vpn: <POINTOPOINT,MULTICAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UNKNOWN qlen 100 link/none inet 10.200.2.235/22 brd 10.200.3.255 scope global vpn # ip rule show 0: from all lookup local 32764: from all fwmark 0x3 lookup VPN 32765: from 192.168.0.32/27 lookup VPN 32766: from all lookup main 32767: from all lookup default # ip route show table VPN default via 10.200.0.1 dev vpn 10.200.0.0/22 dev vpn proto kernel scope link src 10.200.2.235 192.168.0.0/24 dev lan proto kernel scope link src 192.168.0.5 # ip route show default via 192.168.0.1 dev lan metric 100 10.200.0.0/22 dev vpn proto kernel scope link src 10.200.2.235 192.168.0.0/24 dev lan proto kernel scope link src 192.168.0.5 TCP dump showing no traffic coming back when connection is made from 192.168.0.5 user 2000 # tcpdump -i vpn tcpdump: verbose output suppressed, use -v or -vv for full protocol decode listening on vpn, link-type RAW (Raw IP), capture size 65535 bytes ### Traffic from user 2000 on 192.168.0.5 ### 10:19:05.629985 IP 10.200.2.235.37291 > 10.100-78-194.akamai.com.http: Flags [S], seq 2868799562, win 14600, options [mss 1460,sackOK,TS val 6887764 ecr 0,nop,wscale 4], length 0 10:19:21.678001 IP 10.200.2.235.37291 > 10.100-78-194.akamai.com.http: Flags [S], seq 2868799562, win 14600, options [mss 1460,sackOK,TS val 6891776 ecr 0,nop,wscale 4], length 0 ### Traffic from 192.168.0.35 ### 10:23:12.066174 IP 10.200.2.235.49247 > 10.100-78-194.akamai.com.http: Flags [S], seq 2294159276, win 65535, options [mss 1460,nop,wscale 4,nop,nop,TS val 557451322 ecr 0,sackOK,eol], length 0 10:23:12.265640 IP 10.100-78-194.akamai.com.http > 10.200.2.235.49247: Flags [S.], seq 2521908813, ack 2294159277, win 14480, options [mss 1367,sackOK,TS val 388565772 ecr 557451322,nop,wscale 1], length 0 10:23:12.276573 IP 10.200.2.235.49247 > 10.100-78-194.akamai.com.http: Flags [.], ack 1, win 8214, options [nop,nop,TS val 557451534 ecr 388565772], length 0 10:23:12.293030 IP 10.200.2.235.49247 > 10.100-78-194.akamai.com.http: Flags [P.], seq 1:480, ack 1, win 8214, options [nop,nop,TS val 557451552 ecr 388565772], length 479 10:23:12.574773 IP 10.100-78-194.akamai.com.http > 10.200.2.235.49247: Flags [.], ack 480, win 7776, options [nop,nop,TS val 388566081 ecr 557451552], length 0

  Read the article

• Can't log in via SSH to any accounts set to use /bin/bash as a default shell

  - by Gui Ambros

  I'm trying to install bash as the default shell on a ARM Linux running on an embedded device (Synology DS212+ NAS). But there's something really wrong, and I can't figure out what it is. Symptoms: 1) Root has /bin/bash as default shell, and can log in normally via SSH: $ grep root /etc/passwd root:x:0:0:root:/root:/bin/bash $ ssh root@NAS root@NAS's password: Last login: Sun Dec 16 14:06:56 2012 from desktop # 2) joeuser has /bin/bash as default shell, and receives "Permission denied" when trying to log in via SSH: $ grep joeuser /etc/passwd joeuser:x:1029:100:Joe User:/home/joeuser:/bin/bash $ ssh joeuser@localhost joeuser@NAS's password: Last login: Sun Dec 16 14:07:22 2012 from desktop Permission denied, please try again. Connection to localhost closed. 3) changing joeuser's shell back to /bin/sh: $ grep joeuser /etc/passwd joeuser:x:1029:100:Joe User:/home/joeuser:/bin/sh $ ssh joeuser@localhost Last login: Sun Dec 16 15:50:52 2012 from localhost $ To make things even more strange, I can log in as joeuser using /bin/bash using the serial console (!). Also a su - joeuser as root works fine, so the bash binary itself is working fine. In an act of despair, I changed joeuser's uid to 0 on /etc/passwd, but also didn't work, so it doesn't seem to be anything permission related. Seems that bash is doing some extra checking that sshd didn't like, and blocking the connections for non-root users. Maybe some sort of sanity checking - or terminal emulation - that is triggering the SIGCHLD, but only when called via ssh. I already went through every single item on sshd_config, and also put SSHD in debug mode, but didn't find anything strange. Here's my /etc/ssh/sshd_config: LogLevel DEBUG LoginGraceTime 2m PermitRootLogin yes RSAAuthentication yes PubkeyAuthentication yes AuthorizedKeysFile %h/.ssh/authorized_keys ChallengeResponseAuthentication no UsePAM yes AllowTcpForwarding no ChrootDirectory none Subsystem sftp internal-sftp -f DAEMON -u 000 And here's the output from /usr/syno/sbin/sshd -d, showing the failed attempt of joeuser trying to log in, with /bin/bash as the shell: debug1: Config token is loglevel debug1: Config token is logingracetime debug1: Config token is permitrootlogin debug1: Config token is rsaauthentication debug1: Config token is pubkeyauthentication debug1: Config token is authorizedkeysfile debug1: Config token is challengeresponseauthentication debug1: Config token is usepam debug1: Config token is allowtcpforwarding debug1: Config token is chrootdirectory debug1: Config token is subsystem debug1: HPN Buffer Size: 87380 debug1: sshd version OpenSSH_5.8p1-hpn13v11 debug1: read PEM private key done: type RSA debug1: private host key: #0 type 1 RSA debug1: read PEM private key done: type DSA debug1: private host key: #1 type 2 DSA debug1: read PEM private key done: type ECDSA debug1: private host key: #2 type 3 ECDSA debug1: rexec_argv[0]='/usr/syno/sbin/sshd' debug1: rexec_argv[1]='-d' Set /proc/self/oom_adj from 0 to -17 debug1: Bind to port 22 on ::. debug1: Server TCP RWIN socket size: 87380 debug1: HPN Buffer Size: 87380 Server listening on :: port 22. debug1: Bind to port 22 on 0.0.0.0. debug1: Server TCP RWIN socket size: 87380 debug1: HPN Buffer Size: 87380 Server listening on 0.0.0.0 port 22. debug1: Server will not fork when running in debugging mode. debug1: rexec start in 6 out 6 newsock 6 pipe -1 sock 9 debug1: inetd sockets after dupping: 4, 4 Connection from 127.0.0.1 port 52212 debug1: HPN Disabled: 0, HPN Buffer Size: 87380 debug1: Client protocol version 2.0; client software version OpenSSH_5.8p1-hpn13v11 SSH: Server;Ltype: Version;Remote: 127.0.0.1-52212;Protocol: 2.0;Client: OpenSSH_5.8p1-hpn13v11 debug1: match: OpenSSH_5.8p1-hpn13v11 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.8p1-hpn13v11 debug1: permanently_set_uid: 1024/100 debug1: MYFLAG IS 1 debug1: list_hostkey_types: ssh-rsa,ssh-dss,ecdsa-sha2-nistp256 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: AUTH STATE IS 0 debug1: REQUESTED ENC.NAME is 'aes128-ctr' debug1: kex: client->server aes128-ctr hmac-md5 none SSH: Server;Ltype: Kex;Remote: 127.0.0.1-52212;Enc: aes128-ctr;MAC: hmac-md5;Comp: none debug1: REQUESTED ENC.NAME is 'aes128-ctr' debug1: kex: server->client aes128-ctr hmac-md5 none debug1: expecting SSH2_MSG_KEX_ECDH_INIT debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: KEX done debug1: userauth-request for user joeuser service ssh-connection method none SSH: Server;Ltype: Authname;Remote: 127.0.0.1-52212;Name: joeuser debug1: attempt 0 failures 0 debug1: Config token is loglevel debug1: Config token is logingracetime debug1: Config token is permitrootlogin debug1: Config token is rsaauthentication debug1: Config token is pubkeyauthentication debug1: Config token is authorizedkeysfile debug1: Config token is challengeresponseauthentication debug1: Config token is usepam debug1: Config token is allowtcpforwarding debug1: Config token is chrootdirectory debug1: Config token is subsystem debug1: PAM: initializing for "joeuser" debug1: PAM: setting PAM_RHOST to "localhost" debug1: PAM: setting PAM_TTY to "ssh" debug1: userauth-request for user joeuser service ssh-connection method password debug1: attempt 1 failures 0 debug1: do_pam_account: called Accepted password for joeuser from 127.0.0.1 port 52212 ssh2 debug1: monitor_child_preauth: joeuser has been authenticated by privileged process debug1: PAM: establishing credentials User child is on pid 9129 debug1: Entering interactive session for SSH2. debug1: server_init_dispatch_20 debug1: server_input_channel_open: ctype session rchan 0 win 65536 max 16384 debug1: input_session_request debug1: channel 0: new [server-session] debug1: session_new: session 0 debug1: session_open: channel 0 debug1: session_open: session 0: link with channel 0 debug1: server_input_channel_open: confirm session debug1: server_input_global_request: rtype [email protected] want_reply 0 debug1: server_input_channel_req: channel 0 request pty-req reply 1 debug1: session_by_channel: session 0 channel 0 debug1: session_input_channel_req: session 0 req pty-req debug1: Allocating pty. debug1: session_new: session 0 debug1: session_pty_req: session 0 alloc /dev/pts/1 debug1: server_input_channel_req: channel 0 request shell reply 1 debug1: session_by_channel: session 0 channel 0 debug1: session_input_channel_req: session 0 req shell debug1: Setting controlling tty using TIOCSCTTY. debug1: Received SIGCHLD. debug1: session_by_pid: pid 9130 debug1: session_exit_message: session 0 channel 0 pid 9130 debug1: session_exit_message: release channel 0 debug1: session_by_tty: session 0 tty /dev/pts/1 debug1: session_pty_cleanup: session 0 release /dev/pts/1 Received disconnect from 127.0.0.1: 11: disconnected by user debug1: do_cleanup debug1: do_cleanup debug1: PAM: cleanup debug1: PAM: closing session debug1: PAM: deleting credentials Here you have the full output of sshd -dd, together with ssh -vv. Bash: # bash --version GNU bash, version 3.2.49(1)-release (arm-none-linux-gnueabi) Copyright (C) 2007 Free Software Foundation, Inc. The bash binary was cross compiled from source. I also tried using a pre-compiled binary from the Optware distribution, but had the exact same problem. I checked for missing shared libraries using objdump -x, but they're all there. Any ideas what could be causing this "Permission denied, please try again."? I'm almost diving in the bash source code to investigate, but trying to avoid hours chasing something that may be silly.

  Read the article

• My linux server takes more than an hour to boot. Suggestions?

  - by jamieb

  I am building a CentOS 5.4 system that boots off a compact flash card using a card reader that emulates an IDE drive. It literally takes about an hour to boot. The ultra-slow part occurs when Grub is loading the kernel. Once that's done, the rest of the boot process only takes about a minute to get to a login prompt. Does anyone have any suggestions? I suspect that it may have to do with UDMA. Everything IDE-related in my BIOS seems to checkout. The read performance hdparm is telling me 1.77 MB/s. Ouch! (But even at that rate, it still shouldn't take an hour to decompress and load the kernel) [root@server ~]# hdparm -tT /dev/hdc /dev/hdc: Timing cached reads: 2444 MB in 2.00 seconds = 1222.04 MB/sec Timing buffered disk reads: 6 MB in 3.39 seconds = 1.77 MB/sec Trying to enable DMA is a no-go though: [root@server ~]# hdparm -d1 /dev/hdc /dev/hdc: setting using_dma to 1 (on) HDIO_SET_DMA failed: Operation not permitted using_dma = 0 (off) Here's some command outputs that might help: System [root@server ~]# uname -a Linux server.localdomain 2.6.18-164.el5xen #1 SMP Thu Sep 3 04:47:32 EDT 2009 i686 i686 i386 GNU/Linux PCI info: [root@server ~]# lspci -v 00:00.0 Host bridge: Intel Corporation 82945G/GZ/P/PL Memory Controller Hub (rev 02) Subsystem: Intel Corporation 82945G/GZ/P/PL Memory Controller Hub Flags: bus master, fast devsel, latency 0 Capabilities: [e0] Vendor Specific Information 00:02.0 VGA compatible controller: Intel Corporation 82945G/GZ Integrated Graphics Controller (rev 02) (prog-if 00 [VGA controller]) Subsystem: Intel Corporation 82945G/GZ Integrated Graphics Controller Flags: bus master, fast devsel, latency 0, IRQ 10 Memory at fdf00000 (32-bit, non-prefetchable) [size=512K] I/O ports at ff00 [size=8] Memory at d0000000 (32-bit, prefetchable) [size=256M] Memory at fdf80000 (32-bit, non-prefetchable) [size=256K] Capabilities: [90] Message Signalled Interrupts: 64bit- Queue=0/0 Enable- Capabilities: [d0] Power Management version 2 00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 (rev 01) (prog-if 00 [UHCI]) Subsystem: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 Flags: bus master, medium devsel, latency 0, IRQ 16 I/O ports at fe00 [size=32] 00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 (rev 01) (prog-if 00 [UHCI]) Subsystem: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 Flags: bus master, medium devsel, latency 0, IRQ 17 I/O ports at fd00 [size=32] 00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 (rev 01) (prog-if 00 [UHCI]) Subsystem: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 Flags: bus master, medium devsel, latency 0, IRQ 18 I/O ports at fc00 [size=32] 00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 (rev 01) (prog-if 00 [UHCI]) Subsystem: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 Flags: bus master, medium devsel, latency 0, IRQ 19 I/O ports at fb00 [size=32] 00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 01) (prog-if 20 [EHCI]) Subsystem: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller Flags: bus master, medium devsel, latency 0, IRQ 16 Memory at fdfff000 (32-bit, non-prefetchable) [size=1K] Capabilities: [50] Power Management version 2 Capabilities: [58] Debug port 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1) (prog-if 01 [Subtractive decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=32 I/O behind bridge: 0000d000-0000dfff Memory behind bridge: fde00000-fdefffff Prefetchable memory behind bridge: 00000000fdd00000-00000000fdd00000 Capabilities: [50] #0d [0000] 00:1f.0 ISA bridge: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge (rev 01) Subsystem: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge Flags: bus master, medium devsel, latency 0 Capabilities: [e0] Vendor Specific Information 00:1f.2 IDE interface: Intel Corporation 82801GB/GR/GH (ICH7 Family) SATA IDE Controller (rev 01) (prog-if 80 [Master]) Subsystem: Intel Corporation 82801GB/GR/GH (ICH7 Family) SATA IDE Controller Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 17 I/O ports at <unassigned> I/O ports at <unassigned> I/O ports at <unassigned> I/O ports at <unassigned> I/O ports at f800 [size=16] Capabilities: [70] Power Management version 2 00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 01) Subsystem: Intel Corporation 82801G (ICH7 Family) SMBus Controller Flags: medium devsel, IRQ 17 I/O ports at 0500 [size=32] 01:04.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) Subsystem: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ Flags: bus master, medium devsel, latency 32, IRQ 18 I/O ports at de00 [size=256] Memory at fdeff000 (32-bit, non-prefetchable) [size=256] Capabilities: [50] Power Management version 2 01:06.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) Subsystem: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ Flags: bus master, medium devsel, latency 32, IRQ 17 I/O ports at dc00 [size=256] Memory at fdefe000 (32-bit, non-prefetchable) [size=256] Capabilities: [50] Power Management version 2 01:07.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) Subsystem: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ Flags: bus master, medium devsel, latency 32, IRQ 19 I/O ports at da00 [size=256] Memory at fdefd000 (32-bit, non-prefetchable) [size=256] Capabilities: [50] Power Management version 2 hdparm ouput: [root@server ~]# hdparm /dev/hdc /dev/hdc: multcount = 0 (off) IO_support = 0 (default 16-bit) unmaskirq = 0 (off) using_dma = 0 (off) keepsettings = 0 (off) readonly = 0 (off) readahead = 256 (on) geometry = 8146/16/63, sectors = 8211168, start = 0 [root@server ~]# hdparm -I /dev/hdc /dev/hdc: ATA device, with non-removable media Model Number: InnoDisk Corp. - iCF4000 4GB Serial Number: 20091023AACA70000753 Firmware Revision: 081107 Standards: Supported: 5 Likely used: 6 Configuration: Logical max current cylinders 8146 8146 heads 16 16 sectors/track 63 63 -- CHS current addressable sectors: 8211168 LBA user addressable sectors: 8211168 device size with M = 1024*1024: 4009 MBytes device size with M = 1000*1000: 4204 MBytes (4 GB) Capabilities: LBA, IORDY(can be disabled) Standby timer values: spec'd by Vendor R/W multiple sector transfer: Max = 2 Current = 2 DMA: mdma0 mdma1 mdma2 udma0 udma1 *udma2 udma3 udma4 Cycle time: min=120ns recommended=120ns PIO: pio0 pio1 pio2 pio3 pio4 Cycle time: no flow control=120ns IORDY flow control=120ns Commands/features: Enabled Supported: * Power Management feature set * WRITE_BUFFER command * READ_BUFFER command * NOP cmd * CFA feature set * Mandatory FLUSH_CACHE HW reset results: CBLID- above Vih Device num = 0 CFA power mode 1: enabled and required by some commands Maximum current = 100ma Checksum: correct

  Read the article

• squid3 auth thru samba using ntlm to AD doesn't work

  - by derty

  some users here are spending to much time exploring the WWW. So big boss whats to get this under control. We use a squid3 just for some security reason and chace benefits. and now i'm trying to set up a new proxy on a different server (Debian 6) Permissions are defined in AC and the squid3 should get the auth thru samba/winbind by using the ntlm protocol. but i'll get all the time Access, denited. it only works by using LDAP but thats not the way i need it. here some log and confs squid access.log 1326878095.784 1 192.168.15.27 TCP_DENIED/407 4049 GET http://at.msn.com/? -NONE/- text/html 1326878095.791 1 192.168.15.27 TCP_DENIED/407 4294 GET http://at.msn.com/? - NONE/- text/html 1326878095.803 9 192.168.15.27 TCP_DENIED/403 4028 GET http://at.msn.com/? kavan NONE/- text/html 1326878095.848 0 192.168.15.27 TCP_DENIED/403 3881 GET http://www.squid-cache.org/Artwork/SN.png kavan NONE/- text/html 1326878100.279 0 192.168.15.27 TCP_DENIED/403 3735 GET http://www.google.at/ kavan NONE/- text/html 1326878100.296 0 192.168.15.27 TCP_DENIED/403 3870 GET http://www.squid-cache.org/Artwork/SN.png kavan NONE/- text/html 1326878155.700 0 192.168.15.27 TCP_DENIED/407 4072 GET http://ie9cvlist.ie.microsoft.com/IE9CompatViewList.xml - NONE/- text/html 1326878155.705 2 192.168.15.27 TCP_DENIED/407 4317 GET http://ie9cvlist.ie.microsoft.com/IE9CompatViewList.xml - NONE/- text/html 1326878155.709 3 192.168.15.27 TCP_DENIED/403 4026 GET http://ie9cvlist.ie.microsoft.com/IE9CompatViewList.xml kavan NONE/- text/html squid chace 2012/01/18 10:12:49| Creating Swap Directories 2012/01/18 10:12:49| Starting Squid Cache version 3.1.6 for x86_64-pc-linux-gnu... 2012/01/18 10:12:49| Process ID 17236 2012/01/18 10:12:49| With 65535 file descriptors available 2012/01/18 10:12:49| Initializing IP Cache... 2012/01/18 10:12:49| DNS Socket created at [::], FD 7 2012/01/18 10:12:49| DNS Socket created at 0.0.0.0, FD 8 2012/01/18 10:12:49| Adding nameserver 192.168.15.2 from /etc/resolv.conf 2012/01/18 10:12:49| Adding nameserver 192.168.15.19 from /etc/resolv.conf 2012/01/18 10:12:49| Adding nameserver 192.168.15.1 from /etc/resolv.conf 2012/01/18 10:12:49| Adding domain schoenbrunn.local from /etc/resolv.conf 2012/01/18 10:12:49| helperOpenServers: Starting 5/5 'squid_ldap_auth' processes 2012/01/18 10:12:49| helperOpenServers: Starting 10/10 'ntlm_auth' processes 2012/01/18 10:12:49| helperOpenServers: Starting 10/10 'squid_kerb_auth' processes 2012/01/18 10:12:49| squid_kerb_auth: INFO: Starting version 1.0.5 2012/01/18 10:12:49| squid_kerb_auth: INFO: Starting version 1.0.5 2012/01/18 10:12:49| squid_kerb_auth: INFO: Starting version 1.0.5 2012/01/18 10:12:49| squid_kerb_auth: INFO: Starting version 1.0.5 2012/01/18 10:12:49| squid_kerb_auth: INFO: Starting version 1.0.5 2012/01/18 10:12:49| squid_kerb_auth: INFO: Starting version 1.0.5 2012/01/18 10:12:49| squid_kerb_auth: INFO: Starting version 1.0.5 2012/01/18 10:12:49| squid_kerb_auth: INFO: Starting version 1.0.5 2012/01/18 10:12:49| helperOpenServers: Starting 5/5 'squid_ldap_group' processes 2012/01/18 10:12:49| squid_kerb_auth: INFO: Starting version 1.0.5 2012/01/18 10:12:49| squid_kerb_auth: INFO: Starting version 1.0.5 2012/01/18 10:12:49| Unlinkd pipe opened on FD 73 2012/01/18 10:12:49| Local cache digest enabled; rebuild/rewrite every 3600/3600 sec 2012/01/18 10:12:49| Store logging disabled 2012/01/18 10:12:49| Swap maxSize 0 + 262144 KB, estimated 20164 objects 2012/01/18 10:12:49| Target number of buckets: 1008 2012/01/18 10:12:49| Using 8192 Store buckets 2012/01/18 10:12:49| Max Mem size: 262144 KB 2012/01/18 10:12:49| Max Swap size: 0 KB 2012/01/18 10:12:49| Using Least Load store dir selection 2012/01/18 10:12:49| Set Current Directory to /var/spool/squid3 2012/01/18 10:12:49| Loaded Icons. 2012/01/18 10:12:49| Accepting HTTP connections at [::]:3128, FD 74. 2012/01/18 10:12:49| HTCP Disabled. 2012/01/18 10:12:49| Squid modules loaded: 0 2012/01/18 10:12:49| Adaptation support is off. 2012/01/18 10:12:49| Ready to serve requests. 2012/01/18 10:12:50| storeLateRelease: released 0 objects smb.conf # Domain Authntication Settings workgroup = <WORKGROUP> security = ads password server = <DOMAINNAME>.LOCAL realm = <DOMAINNAME>.LOCAL ldap ssl = no # logging log level = 5 max log size = 50 # logs split per machine log file = /var/log/samba/%m.log # max 50KB per log file, then rotate ; max log size = 50 # User settings username map = /etc/samba/smbusers idmap uid = 10000-20000000 idmap gid = 10000-20000000 idmap backend = ad ; template primary group = <ad group> template shell = /sbin/nologin # Winbind Settings winbind separator = + winbind enum users = Yes winbind enum groups = Yes winbind netsted groups = Yes winbind nested groups = Yes winbind cache time = 10 winbind use default domain = Yes #Other Globals unix charset = LOCALE server string = <SERVERNAME> load printers = no printing = cups cups options = raw ; printcap name = /etc/printcap #obtain list of printers automatically on SystemV ; printcap name = lpstat ; printing = cups squid.conf auth_param ntlm program /usr/bin/ntlm_auth --require-membership-of=<DOMAINNAME>\\INTERNETZ --helper-protocol=squid-2.5-ntlmssp auth_param ntlm children 10 auth_param basic program /usr/lib/squid3/squid_ldap_auth -R -b "dc=<dcname>,dc=local" -D "cn=administrator,cn=Users,dc=<domainname>,dc=local" -w "******" -f sAMAccountName=%s -h 192.168.15.19:3268 auth_param basic realm "Proxy Authentifizierung. Bitte geben Sie Ihren Benutzername und Ihr Passwort ein!" #means insert you PW in an other language - # external_acl_type InetGroup %LOGIN /usr/lib/squid3/squid_ldap_group -R -b "dc=<domainname>,dc=local" -D "cn=administrator,cn=Users,dc=<domainname>,dc=local" -w "******" -f "(&(objectclass=person)(sAMAccountName=%v) (memberof=cn=%a,cn=internetz,dc=<domainname>,dc=local))" -h 192.168.15.19:3268 auth_param negotiate program /usr/lib/squid3/squid_kerb_auth -d auth_param negotiate children 10 auth_param negotiate keep_alive on acl localnet proxy_auth REQUIRED acl InetAccess external InetGroup Internetz http_access allow InetAccess http_access deny all acl auth proxy_auth REQUIRED http_access allow auth and a very suspicious is that by adding the proxy server to the Domain i see 2 new entries in the PC one with the original computer-name leopoldine and one with leopoldine CNF:f8efa4c4-ff0e-4217-939d-f1523b43464d ?!? I tried a lot, really... but i stuck on this problem... i actually i even reinstalled all dependent programs and reconfigured them from default. Group exists and has me in it. Firefox running on the old proxy and i use IE for testing the new one. But i'll get all the time Access-Denited and to be honest i'm quite a beginner, so please don't be to prude. I'll interested in improving, i'll get the information we need to fix this but i started working 2 month ago and got only 1 1/2 year's training and not a single sec. in linux ;)

  Read the article

• What do I do when I get a Linux kernel bug?

  - by raldi

  I just bought a tiny computer called a fit-pc2 which came with a somewhat customized Ubuntu 9.10 installation. uname -a reports: Linux 2.6.31-34-fitpc2 #7 SMP Thu Apr 22 17:43:26 IDT 2010 i686 GNU/Linux It seems that after several hours of running with heavy network load, all networking ceases and I get the following in kern.log: BUG: unable to handle kernel paging request at ff09dfc0 IP: [<c0150300>] kthread_should_stop+0x10/0x20 *pde = 00000000 Oops: 0000 [#1] SMP last sysfs file: /sys/devices/pci0000:00/0000:00:1d.7/usb1/idVendor Modules linked in: binfmt_misc ppdev sbc_fitpc2_wdt snd_usb_audio snd_usb_lib i2c_isch sch_gpio snd_seq_dummy snd_hda_intel snd_pcm_oss snd_seq_oss snd_seq_midi snd_rawmidi snd_mixer_oss snd_seq_midi_event snd_seq snd_pcm snd_timer snd_page_alloc snd_seq_device iptable_filter ip_tables x_tables snd_hwdep lpc_sch snd psmouse rt2860sta(C) uvcvideo video pl2303 soundcore mfd_core output videodev v4l1_compat lirc_igorplugusb lirc_dev serio_raw lp parport usbhid r8169 mii iegd_mod drm agpgart Pid: 16, comm: kblockd/1 Tainted: G C (2.6.31-34-fitpc2 #7) SBC-FITPC2 EIP: 0060:[<c0150300>] EFLAGS: 00010246 CPU: 1 EIP is at kthread_should_stop+0x10/0x20 EAX: ff09dfc4 EBX: c180cbac ECX: 0109d000 EDX: f709df98 ESI: f709df98 EDI: c180cba0 EBP: f709dfb8 ESP: f709df90 DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068 Process kblockd/1 (pid: 16, ti=f709c000 task=f7084b60 task.ti=f709c000) Stack: c014c14d c180cba4 00000000 f7084b60 c0150770 f709dfa4 f709dfa4 f7023ef4 <0> c180cba0 c014c0d0 f709dfe0 c015047c 00000000 00000000 00000000 f709dfcc <0> f709dfcc c0150400 00000000 00000000 00000000 c0103ce7 f7023ef4 00000000 Call Trace: [<c014c14d>] ? worker_thread+0x7d/0xe0 [<c0150770>] ? autoremove_wake_function+0x0/0x40 [<c014c0d0>] ? worker_thread+0x0/0xe0 [<c015047c>] ? kthread+0x7c/0x90 [<c0150400>] ? kthread+0x0/0x90 [<c0103ce7>] ? kernel_thread_helper+0x7/0x10 Code: a6 8b 55 0c 8d 4d e0 89 f8 89 34 24 e8 7a fd ff ff 89 c3 eb 92 90 90 90 90 90 90 55 64 a1 00 80 76 c0 8b 80 70 02 00 00 89 e5 5d <8b> 40 fc c3 8d b6 00 00 00 00 8d bf 00 00 00 00 55 ba d7 86 62 EIP: [<c0150300>] kthread_should_stop+0x10/0x20 SS:ESP 0068:f709df90 CR2: 00000000ff09dfc0 ---[ end trace 06004df70b9cf435 ]--- BUG: unable to handle kernel paging request at ff09dfc8 IP: [<c0521bc8>] _spin_lock_irqsave+0x18/0x30 *pde = 00000000 Oops: 0002 [#2] SMP last sysfs file: /sys/devices/pci0000:00/0000:00:1d.7/usb1/idVendor Modules linked in: binfmt_misc ppdev sbc_fitpc2_wdt snd_usb_audio snd_usb_lib i2c_isch sch_gpio snd_seq_dummy snd_hda_intel snd_pcm_oss snd_seq_oss snd_seq_midi snd_rawmidi snd_mixer_oss snd_seq_midi_event snd_seq snd_pcm snd_timer snd_page_alloc snd_seq_device iptable_filter ip_tables x_tables snd_hwdep lpc_sch snd psmouse rt2860sta(C) uvcvideo video pl2303 soundcore mfd_core output videodev v4l1_compat lirc_igorplugusb lirc_dev serio_raw lp parport usbhid r8169 mii iegd_mod drm agpgart Pid: 16, comm: kblockd/1 Tainted: G D C (2.6.31-34-fitpc2 #7) SBC-FITPC2 EIP: 0060:[<c0521bc8>] EFLAGS: 00010086 CPU: 1 EIP is at _spin_lock_irqsave+0x18/0x30 EAX: 00000100 EBX: ff09dfc8 ECX: 00000286 EDX: ff09dfc8 ESI: f7084b60 EDI: ff09dfc4 EBP: f709dd88 ESP: f709dd88 DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068 Process kblockd/1 (pid: 16, ti=f709c000 task=f7084b60 task.ti=f709c000) Stack: f709dda4 c0127c0b 00000082 00000001 ff09dfc4 f7084b60 00000000 f709ddd0 <0> c0137fd2 00000086 f70954c4 00000000 f7098480 f709ddf0 f7094fc0 f7084b60 <0> 00000000 00000009 f709ddf0 c013c3f8 00000001 c1807c60 f709ddf0 f7084b60 Call Trace: [<c0127c0b>] ? complete+0x1b/0x60 [<c0137fd2>] ? mm_release+0x52/0xf0 [<c013c3f8>] ? exit_mm+0x18/0x110 [<c013c6db>] ? do_exit+0xfb/0x2e0 [<c013998a>] ? print_oops_end_marker+0x2a/0x30 [<c0522aab>] ? oops_end+0x8b/0xd0 [<c011eac4>] ? no_context+0xb4/0xd0 [<c011eb1d>] ? __bad_area_nosemaphore+0x3d/0x1a0 [<c0133a56>] ? load_balance_newidle+0x96/0x320 [<c011ec92>] ? bad_area_nosemaphore+0x12/0x20 [<c0524106>] ? do_page_fault+0x2f6/0x380 [<c012cc30>] ? finish_task_switch+0x50/0xe0 [<c0523e10>] ? do_page_fault+0x0/0x380 [<c0522006>] ? error_code+0x66/0x70 [<c0523e10>] ? do_page_fault+0x0/0x380 [<c0150300>] ? kthread_should_stop+0x10/0x20 [<c014c14d>] ? worker_thread+0x7d/0xe0 [<c0150770>] ? autoremove_wake_function+0x0/0x40 [<c014c0d0>] ? worker_thread+0x0/0xe0 [<c015047c>] ? kthread+0x7c/0x90 [<c0150400>] ? kthread+0x0/0x90 [<c0103ce7>] ? kernel_thread_helper+0x7/0x10 Code: 00 00 00 55 89 e5 f0 83 28 01 79 05 e8 02 ff ff ff 5d c3 55 89 c2 89 e5 9c 58 8d 74 26 00 89 c1 fa 90 8d 74 26 00 b8 00 01 00 00 <f0> 66 0f c1 02 38 e0 74 06 f3 90 8a 02 eb f6 89 c8 5d c3 90 8d EIP: [<c0521bc8>] _spin_lock_irqsave+0x18/0x30 SS:ESP 0068:f709dd88 CR2: 00000000ff09dfc8 ---[ end trace 06004df70b9cf436 ]--- Fixing recursive fault but reboot is needed! This seems to happen at least once a day. How do I even begin to debug this?

  Read the article

• What do I do when I get a Linux kernel bug?

  - by raldi

  I just bought a tiny computer called a fit-pc2 which came with a somewhat customized Ubuntu 9.10 installation. uname -a reports: Linux 2.6.31-34-fitpc2 #7 SMP Thu Apr 22 17:43:26 IDT 2010 i686 GNU/Linux It seems that after several hours of running with heavy network load, all networking ceases and I get the following in kern.log: BUG: unable to handle kernel paging request at ff09dfc0 IP: [<c0150300>] kthread_should_stop+0x10/0x20 *pde = 00000000 Oops: 0000 [#1] SMP last sysfs file: /sys/devices/pci0000:00/0000:00:1d.7/usb1/idVendor Modules linked in: binfmt_misc ppdev sbc_fitpc2_wdt snd_usb_audio snd_usb_lib i2c_isch sch_gpio snd_seq_dummy snd_hda_intel snd_pcm_oss snd_seq_oss snd_seq_midi snd_rawmidi snd_mixer_oss snd_seq_midi_event snd_seq snd_pcm snd_timer snd_page_alloc snd_seq_device iptable_filter ip_tables x_tables snd_hwdep lpc_sch snd psmouse rt2860sta(C) uvcvideo video pl2303 soundcore mfd_core output videodev v4l1_compat lirc_igorplugusb lirc_dev serio_raw lp parport usbhid r8169 mii iegd_mod drm agpgart Pid: 16, comm: kblockd/1 Tainted: G C (2.6.31-34-fitpc2 #7) SBC-FITPC2 EIP: 0060:[<c0150300>] EFLAGS: 00010246 CPU: 1 EIP is at kthread_should_stop+0x10/0x20 EAX: ff09dfc4 EBX: c180cbac ECX: 0109d000 EDX: f709df98 ESI: f709df98 EDI: c180cba0 EBP: f709dfb8 ESP: f709df90 DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068 Process kblockd/1 (pid: 16, ti=f709c000 task=f7084b60 task.ti=f709c000) Stack: c014c14d c180cba4 00000000 f7084b60 c0150770 f709dfa4 f709dfa4 f7023ef4 <0> c180cba0 c014c0d0 f709dfe0 c015047c 00000000 00000000 00000000 f709dfcc <0> f709dfcc c0150400 00000000 00000000 00000000 c0103ce7 f7023ef4 00000000 Call Trace: [<c014c14d>] ? worker_thread+0x7d/0xe0 [<c0150770>] ? autoremove_wake_function+0x0/0x40 [<c014c0d0>] ? worker_thread+0x0/0xe0 [<c015047c>] ? kthread+0x7c/0x90 [<c0150400>] ? kthread+0x0/0x90 [<c0103ce7>] ? kernel_thread_helper+0x7/0x10 Code: a6 8b 55 0c 8d 4d e0 89 f8 89 34 24 e8 7a fd ff ff 89 c3 eb 92 90 90 90 90 90 90 55 64 a1 00 80 76 c0 8b 80 70 02 00 00 89 e5 5d <8b> 40 fc c3 8d b6 00 00 00 00 8d bf 00 00 00 00 55 ba d7 86 62 EIP: [<c0150300>] kthread_should_stop+0x10/0x20 SS:ESP 0068:f709df90 CR2: 00000000ff09dfc0 ---[ end trace 06004df70b9cf435 ]--- BUG: unable to handle kernel paging request at ff09dfc8 IP: [<c0521bc8>] _spin_lock_irqsave+0x18/0x30 *pde = 00000000 Oops: 0002 [#2] SMP last sysfs file: /sys/devices/pci0000:00/0000:00:1d.7/usb1/idVendor Modules linked in: binfmt_misc ppdev sbc_fitpc2_wdt snd_usb_audio snd_usb_lib i2c_isch sch_gpio snd_seq_dummy snd_hda_intel snd_pcm_oss snd_seq_oss snd_seq_midi snd_rawmidi snd_mixer_oss snd_seq_midi_event snd_seq snd_pcm snd_timer snd_page_alloc snd_seq_device iptable_filter ip_tables x_tables snd_hwdep lpc_sch snd psmouse rt2860sta(C) uvcvideo video pl2303 soundcore mfd_core output videodev v4l1_compat lirc_igorplugusb lirc_dev serio_raw lp parport usbhid r8169 mii iegd_mod drm agpgart Pid: 16, comm: kblockd/1 Tainted: G D C (2.6.31-34-fitpc2 #7) SBC-FITPC2 EIP: 0060:[<c0521bc8>] EFLAGS: 00010086 CPU: 1 EIP is at _spin_lock_irqsave+0x18/0x30 EAX: 00000100 EBX: ff09dfc8 ECX: 00000286 EDX: ff09dfc8 ESI: f7084b60 EDI: ff09dfc4 EBP: f709dd88 ESP: f709dd88 DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068 Process kblockd/1 (pid: 16, ti=f709c000 task=f7084b60 task.ti=f709c000) Stack: f709dda4 c0127c0b 00000082 00000001 ff09dfc4 f7084b60 00000000 f709ddd0 <0> c0137fd2 00000086 f70954c4 00000000 f7098480 f709ddf0 f7094fc0 f7084b60 <0> 00000000 00000009 f709ddf0 c013c3f8 00000001 c1807c60 f709ddf0 f7084b60 Call Trace: [<c0127c0b>] ? complete+0x1b/0x60 [<c0137fd2>] ? mm_release+0x52/0xf0 [<c013c3f8>] ? exit_mm+0x18/0x110 [<c013c6db>] ? do_exit+0xfb/0x2e0 [<c013998a>] ? print_oops_end_marker+0x2a/0x30 [<c0522aab>] ? oops_end+0x8b/0xd0 [<c011eac4>] ? no_context+0xb4/0xd0 [<c011eb1d>] ? __bad_area_nosemaphore+0x3d/0x1a0 [<c0133a56>] ? load_balance_newidle+0x96/0x320 [<c011ec92>] ? bad_area_nosemaphore+0x12/0x20 [<c0524106>] ? do_page_fault+0x2f6/0x380 [<c012cc30>] ? finish_task_switch+0x50/0xe0 [<c0523e10>] ? do_page_fault+0x0/0x380 [<c0522006>] ? error_code+0x66/0x70 [<c0523e10>] ? do_page_fault+0x0/0x380 [<c0150300>] ? kthread_should_stop+0x10/0x20 [<c014c14d>] ? worker_thread+0x7d/0xe0 [<c0150770>] ? autoremove_wake_function+0x0/0x40 [<c014c0d0>] ? worker_thread+0x0/0xe0 [<c015047c>] ? kthread+0x7c/0x90 [<c0150400>] ? kthread+0x0/0x90 [<c0103ce7>] ? kernel_thread_helper+0x7/0x10 Code: 00 00 00 55 89 e5 f0 83 28 01 79 05 e8 02 ff ff ff 5d c3 55 89 c2 89 e5 9c 58 8d 74 26 00 89 c1 fa 90 8d 74 26 00 b8 00 01 00 00 <f0> 66 0f c1 02 38 e0 74 06 f3 90 8a 02 eb f6 89 c8 5d c3 90 8d EIP: [<c0521bc8>] _spin_lock_irqsave+0x18/0x30 SS:ESP 0068:f709dd88 CR2: 00000000ff09dfc8 ---[ end trace 06004df70b9cf436 ]--- Fixing recursive fault but reboot is needed! This seems to happen at least once a day. How do I even begin to debug this?

  Read the article

• Server hung with "blocked for more than 120 seconds", diskless

  - by alterpub

  I have server which hung every 2-5 days. dmesg show following situation: kernel: [490894.231753] INFO: task munin-html:10187 blocked for more than 120 seconds. kernel: [490894.231799] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. kernel: [490894.231843] munin-html D 0000000000000000 0 10187 9796 0x00000000 kernel: [490894.231878] ffff88063174b968 0000000000000082 ffff88063174b8d8 0000000000015b80 kernel: [490894.231930] ffff88063174bfd8 0000000000015b80 ffff88063174bfd8 ffff88062fe644d0 kernel: [490894.231982] 0000000000015b80 0000000000015b80 ffff88063174bfd8 0000000000015b80 kernel: [490894.232033] Call Trace: kernel: [490894.232059] [<ffffffff8117fce0>] ? sync_buffer+0x0/0x50 kernel: [490894.232089] [<ffffffff815a1f13>] io_schedule+0x73/0xc0 kernel: [490894.232115] [<ffffffff8117fd25>] sync_buffer+0x45/0x50 kernel: [490894.232143] [<ffffffff815a258f>] __wait_on_bit+0x5f/0x90 kernel: [490894.232170] [<ffffffff8117fce0>] ? sync_buffer+0x0/0x50 kernel: [490894.232197] [<ffffffff815a2638>] out_of_line_wait_on_bit+0x78/0x90 kernel: [490894.232227] [<ffffffff81080250>] ? wake_bit_function+0x0/0x40 kernel: [490894.232255] [<ffffffff8117fcd6>] __wait_on_buffer+0x26/0x30 kernel: [490894.232288] [<ffffffffa00131be>] squashfs_read_data+0x1be/0x520 [squashfs] kernel: [490894.232320] [<ffffffff8114f0f1>] ? __mem_cgroup_try_charge+0x71/0x450 kernel: [490894.232350] [<ffffffffa0013963>] squashfs_cache_get+0x1c3/0x320 [squashfs] kernel: [490894.232381] [<ffffffffa00136eb>] ? squashfs_copy_data+0x10b/0x130 [squashfs] kernel: [490894.232426] [<ffffffff815a3dbe>] ? _raw_spin_lock+0xe/0x20 kernel: [490894.232454] [<ffffffffa0013b68>] ? squashfs_read_metadata+0x48/0xf0 [squashfs] kernel: [490894.232499] [<ffffffffa0013ae1>] squashfs_get_datablock+0x21/0x30 [squashfs] kernel: [490894.232544] [<ffffffffa0015026>] squashfs_readpage+0x436/0x4a0 [squashfs] kernel: [490894.232575] [<ffffffff8111a375>] ? __inc_zone_page_state+0x35/0x40 kernel: [490894.232606] [<ffffffff8110d072>] __do_page_cache_readahead+0x172/0x210 kernel: [490894.232636] [<ffffffff8110d131>] ra_submit+0x21/0x30 kernel: [490894.232662] [<ffffffff811045f3>] filemap_fault+0x3f3/0x450 kernel: [490894.232691] [<ffffffff812bd156>] ? prio_tree_insert+0x256/0x2b0 kernel: [490894.232726] [<ffffffffa009225d>] aufs_fault+0x11d/0x170 [aufs] kernel: [490894.232755] [<ffffffff8111f6d4>] __do_fault+0x54/0x560 kernel: [490894.232782] [<ffffffff81122f39>] handle_mm_fault+0x1b9/0x440 kernel: [490894.232811] [<ffffffff811286f5>] ? do_mmap_pgoff+0x335/0x380 kernel: [490894.232840] [<ffffffff815a7af5>] do_page_fault+0x125/0x350 kernel: [490894.232867] [<ffffffff815a4675>] page_fault+0x25/0x30 Os info cat /etc/issue.net Ubuntu 10.04.2 LTS uname -a Linux Shard1Host3 2.6.35-32-server #68~lucid1-Ubuntu SMP Wed Mar 28 18:33:00 UTC 2012 x86_64 GNU/Linux This system load via ltsp and hasn't harddrives also it has a lot of memory 24Gb. free -m total used free shared buffers cached Mem: 24152 17090 7061 0 50 494 -/+ buffers/cache: 16545 7607 Swap: 0 0 0 I put vmstat info here but I think it won't give results after reboot vmstat 1 30 procs -----------memory---------- ---swap-- -----io---- -system-- ----cpu---- r b swpd free buff cache si so bi bo in cs us sy id wa 0 0 0 7231156 52196 506400 0 0 0 0 172 143 7 0 92 0 1 0 0 7231024 52196 506400 0 0 0 0 7859 16233 5 0 94 0 0 0 0 7231024 52196 506400 0 0 0 0 7870 16446 2 0 98 0 0 0 0 7230900 52196 506400 0 0 0 0 7308 15661 5 0 95 0 0 0 0 7231100 52196 506400 0 0 0 0 7960 16543 6 0 94 0 0 0 0 7231100 52196 506400 0 0 0 0 7542 16047 5 1 94 0 3 0 0 7231100 52196 506400 0 0 0 0 7709 16621 3 0 96 0 0 0 0 7231220 52196 506400 0 0 0 0 7857 16552 4 0 96 0 0 0 0 7231220 52196 506400 0 0 0 0 7192 15491 6 0 94 0 0 0 0 7231220 52196 506400 0 0 0 0 7423 15792 5 1 94 0 1 0 0 7231260 52196 506404 0 0 0 0 7686 16296 2 0 98 0 0 0 0 7231260 52196 506404 0 0 0 0 6976 15183 5 0 95 0 0 0 0 7231260 52196 506404 0 0 0 0 7303 15600 4 0 95 0 0 0 0 7231320 52196 506404 0 0 0 0 7967 16241 1 0 98 0 0 0 0 7231444 52196 506404 0 0 0 0 6948 15113 6 0 94 0 0 0 0 7231444 52196 506404 0 0 0 0 7931 16181 6 0 94 0 1 0 0 7231516 52196 506404 0 0 0 0 7715 15829 6 0 94 0 0 0 0 7231516 52196 506404 0 0 0 0 7771 16036 2 0 97 0 0 0 0 7231268 52196 506404 0 0 0 0 7782 16202 6 0 94 0 1 0 0 7231212 52196 506404 0 0 0 0 7457 15622 4 0 96 0 0 0 0 7231212 52196 506404 0 0 0 0 7573 16045 2 0 98 0 2 0 0 7231216 52196 506404 0 0 0 0 7689 16076 6 0 94 0 0 0 0 7231424 52196 506404 0 0 0 0 7429 15650 4 0 95 0 3 0 0 7231424 52196 506404 0 0 0 0 7534 16168 3 0 97 0 1 0 0 7230548 52196 506404 0 0 0 0 8559 15926 7 1 92 0 0 0 0 7230672 52196 506404 0 0 0 0 7720 15905 2 0 98 0 0 0 0 7230548 52196 506404 0 0 0 0 7677 16313 5 0 95 0 1 0 0 7230676 52196 506404 0 0 0 0 7209 15432 5 0 95 0 0 0 0 7230800 52196 506404 0 0 0 0 7522 15861 2 0 98 0 0 0 0 7230552 52196 506404 0 0 0 0 7760 16661 5 0 95 0 In the munin(monitoring system) graphs I see(before server hung): Disk(nbd0) IOs per device: read: 289m but avg by week 2.09m Disk(nbd0) throughput per device: read: 4.73k but avg by week 108.76 Disk(nbd0) utilization per device: 100% but avg by week 1.2% Eth0 traffic was low: in/out only 2Mbps Number of threads increased to 566 usually 392 Fork rate 1.08 but usually 2.82 VMStat(processes state) Increased to 17.77(from 0 as far as I could see in the graph) CPU usage iowait 880.46% when usually 6.67% It'll be great if somebody help me to understand what's up.

  Read the article

• Build and migrated to software raid (mdadm) on GPT disk, now can't assemble array

  - by John H

  mdadm, gpt issues, unrecognized partitions. Simplified question: How do I get mdadm to recognize GPT partitions? I have been attempting to convert/copy my Ubuntu 11.10 OS from a single drive to software raid 1. I have done similar in the past, but in this case, I was adding in a drive that has been configured for GPT and I tried to work with that without fully looking into the implications. Currently, I have a non-booting mdadm RAID 1 array of /dev/md127 (the OS assigned that and it keeps picking up). I am booting off of live USB keys, currently System Rescue CD from sysresccd. While gdisk and parted can see all the partitions, most of the OS utilities do not, including mdadm. My main goal is just to make the raid array accessible so I can get pull the data and start fresh (without using GPT). /dev/md127 /dev/sda /dev/sda1 <- GPT type partition /dev/sda1 <- exists within the GPT part, member of md127 /dev/sda2 <- exists within the GPT part, empty /dev/sdb /dev/sdb1 <- GPT type partition /dev/sdb1 <- exists within the GPT part, member of md127 History: POINT A: The original OS was install on sda (actually /dev/sda6). I used a the Ubuntu live usb to add sdb. I got warning from fdisk about GPT so I used gdisk to create a raid partition (sdb1) and mdadm to create a raid1 mirror with a missing drive. I had many issues getting this working (including being unable to get grub to install) but I eventually got it to boot using grub on sda and /dev/md127 off of sdb. So at point A, I had copied my OS from sda6 to md127 on sdb. I then booted into a rescue mode and attempted to get a bootloader onto sdb, which failed. I then discovered my mistake: I had installed the raid onto sdb instead of sdb1, essentially overwriting the sdb1 partition. POINT B: I now had two copies of my data- one on md127/sdb, and one on sda. I destroyed data on sda and created a new GPT table on sda. I then created sda1 for the raid array, and sda2 for a scratch partition. I added sda1 into the raid array and let it rebuild. md127 now covered /dev/sdb and /dev/sda1 as fully active and synced. POINT C: I rebooted onto linux rescue again and was still able to access the raid array. I then removed /dev/sdb from the array and created /dev/sdb1 for the raid. I added sdb1 to the array and let it sync. I was able to mount and access /dev/md127 without issues. Once it completed, both /dev/sda1 and /dev/sdb1 were GPT partitions and actively syncing. POINT D (current): I rebooted again to test if the array would boot and grub failed to load. I booted off of my live thumb drive and found that I can no longer assemble the raid array. mdadm doesn't see the required partitions. -- root@freshdesk /root % uname -a Linux freshdesk 3.0.24-std251-amd64 #2 SMP Sat Mar 17 12:08:55 UTC 2012 x86_64 AMD Athlon(tm) II X4 645 Processor AuthenticAMD GNU/Linux === /proc/partitions and parted look good: root@freshdesk /root % cat /proc/partitions major minor #blocks name 7 0 301788 loop0 8 0 976762584 sda 8 1 732579840 sda1 8 2 244181703 sda2 8 16 732574584 sdb 8 17 732573543 sdb1 8 32 7876607 sdc 8 33 7873349 sdc1 (parted) print all Model: ATA ST31000528AS (scsi) Disk /dev/sda: 1000GB Sector size (logical/physical): 512B/512B Partition Table: gpt Number Start End Size File system Name Flags 1 1049kB 750GB 750GB ext4 2 750GB 1000GB 250GB Linux/Windows data Model: ATA SAMSUNG HD753LJ (scsi) Disk /dev/sdb: 750GB Sector size (logical/physical): 512B/512B Partition Table: gpt Number Start End Size File system Name Flags 1 1049kB 750GB 750GB ext4 Linux RAID raid Model: SanDisk SanDisk Cruzer (scsi) Disk /dev/sdc: 8066MB Sector size (logical/physical): 512B/512B Partition Table: msdos Number Start End Size Type File system Flags 1 31.7kB 8062MB 8062MB primary fat32 boot, lba === # no sda2, and I double the sdb1 is the one shown in parted root@freshdesk /root % blkid /dev/loop0: TYPE="squashfs" /dev/sda1: UUID="75dd6c2d-f0a8-4302-9da4-792cc7d72355" TYPE="ext4" /dev/sdc1: LABEL="PENDRIVE" UUID="1102-3720" TYPE="vfat" /dev/sdb1: UUID="2dd89f15-65bb-ff88-e368-bf24bd0fce41" TYPE="linux_raid_member" root@freshdesk /root % mdadm -E /dev/sda1 mdadm: No md superblock detected on /dev/sda1. # this is probably a result of me attempting to force the array up, putting superblocks on the GPT partition root@freshdesk /root % mdadm -E /dev/sdb1 /dev/sdb1: Magic : a92b4efc Version : 0.90.00 UUID : 2dd89f15:65bbff88:e368bf24:bd0fce41 Creation Time : Fri Mar 30 19:25:30 2012 Raid Level : raid1 Used Dev Size : 732568320 (698.63 GiB 750.15 GB) Array Size : 732568320 (698.63 GiB 750.15 GB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 127 Update Time : Sat Mar 31 12:39:38 2012 State : clean Active Devices : 1 Working Devices : 2 Failed Devices : 1 Spare Devices : 1 Checksum : a7d038b3 - correct Events : 20195 Number Major Minor RaidDevice State this 2 8 17 2 spare /dev/sdb1 0 0 8 1 0 active sync /dev/sda1 1 1 0 0 1 faulty removed 2 2 8 17 2 spare /dev/sdb1 === root@freshdesk /root % mdadm -A /dev/md127 /dev/sda1 /dev/sdb1 mdadm: no recogniseable superblock on /dev/sda1 mdadm: /dev/sda1 has no superblock - assembly aborted root@freshdesk /root % mdadm -A /dev/md127 /dev/sdb1 mdadm: cannot open device /dev/sdb1: Device or resource busy mdadm: /dev/sdb1 has no superblock - assembly aborted

  Read the article

• curl can't verify cert using capath, but can with cacert option

  - by phylae

  I am trying to use curl to connect to a site using HTTPS. But curl is failing to verify the SSL cert. $ curl --verbose --capath ./certs/ --head https://example.com/ * About to connect() to example.com port 443 (#0) * Trying 1.1.1.1... connected * Connected to example.com (1.1.1.1) port 443 (#0) * successfully set certificate verify locations: * CAfile: none CApath: ./certs/ * SSLv3, TLS handshake, Client hello (1): * SSLv3, TLS handshake, Server hello (2): * SSLv3, TLS handshake, CERT (11): * SSLv3, TLS alert, Server hello (2): * SSL certificate problem, verify that the CA cert is OK. Details: error:14090086:SSL routines:SSL3_GET_SERVER_CERTIFICATE:certificate verify failed * Closing connection #0 curl: (60) SSL certificate problem, verify that the CA cert is OK. Details: error:14090086:SSL routines:SSL3_GET_SERVER_CERTIFICATE:certificate verify failed More details here: http://curl.haxx.se/docs/sslcerts.html curl performs SSL certificate verification by default, using a "bundle" of Certificate Authority (CA) public keys (CA certs). If the default bundle file isn't adequate, you can specify an alternate file using the --cacert option. If this HTTPS server uses a certificate signed by a CA represented in the bundle, the certificate verification probably failed due to a problem with the certificate (it might be expired, or the name might not match the domain name in the URL). If you'd like to turn off curl's verification of the certificate, use the -k (or --insecure) option. I know about the -k option. But I do actually want to verify the cert. The certs directory has been properly hashed with c_rehash . and it contains: A Verisign intermediate cert Two self-signed certs The above site should be verified with the Verisign intermediate cert. When I use the --cacert option instead (and point directly to the Verisign cert) curl is able to verify the SSL cert. $ curl --verbose --cacert ./certs/verisign-intermediate-ca.crt --head https://example.com/ * About to connect() to example.com port 443 (#0) * Trying 1.1.1.1... connected * Connected to example.com (1.1.1.1) port 443 (#0) * successfully set certificate verify locations: * CAfile: ./certs/verisign-intermediate-ca.crt CApath: /etc/ssl/certs * SSLv3, TLS handshake, Client hello (1): * SSLv3, TLS handshake, Server hello (2): * SSLv3, TLS handshake, CERT (11): * SSLv3, TLS handshake, Server finished (14): * SSLv3, TLS handshake, Client key exchange (16): * SSLv3, TLS change cipher, Client hello (1): * SSLv3, TLS handshake, Finished (20): * SSLv3, TLS change cipher, Client hello (1): * SSLv3, TLS handshake, Finished (20): * SSL connection using RC4-SHA * Server certificate: * subject: C=US; ST=State; L=City; O=Company; OU=ou1; CN=example.com * start date: 2011-04-17 00:00:00 GMT * expire date: 2012-04-15 23:59:59 GMT * common name: example.com (matched) * issuer: C=US; O=VeriSign, Inc.; OU=VeriSign Trust Network; OU=Terms of use at https://www.verisign.com/rpa (c)10; CN=VeriSign Class 3 Secure Server CA - G3 * SSL certificate verify ok. > HEAD / HTTP/1.1 > User-Agent: curl/7.19.7 (x86_64-pc-linux-gnu) libcurl/7.19.7 OpenSSL/0.9.8k zlib/1.2.3.3 libidn/1.15 > Host: example.com > Accept: */* > < HTTP/1.1 404 Not Found HTTP/1.1 404 Not Found < Cache-Control: must-revalidate,no-cache,no-store Cache-Control: must-revalidate,no-cache,no-store < Content-Type: text/html;charset=ISO-8859-1 Content-Type: text/html;charset=ISO-8859-1 < Content-Length: 1267 Content-Length: 1267 < Server: Jetty(7.2.2.v20101205) Server: Jetty(7.2.2.v20101205) < * Connection #0 to host example.com left intact * Closing connection #0 * SSLv3, TLS alert, Client hello (1): In addition, if I try hitting one of the sites using a self signed cert and the --capath option, it also works. (Let me know if I should post an example of that.) This implies that curl is finding the cert directory, and it is properly hash. Finally, I am able to verify the SSL cert with openssl, using its -CApath option. $ openssl s_client -CApath ./certs/ -connect example.com:443 CONNECTED(00000003) depth=3 /C=US/O=VeriSign, Inc./OU=Class 3 Public Primary Certification Authority verify return:1 depth=2 /C=US/O=VeriSign, Inc./OU=VeriSign Trust Network/OU=(c) 2006 VeriSign, Inc. - For authorized use only/CN=VeriSign Class 3 Public Primary Certification Authority - G5 verify return:1 depth=1 /C=US/O=VeriSign, Inc./OU=VeriSign Trust Network/OU=Terms of use at https://www.verisign.com/rpa (c)10/CN=VeriSign Class 3 Secure Server CA - G3 verify return:1 depth=0 /C=US/ST=State/L=City/O=Company/OU=ou1/CN=example.com verify return:1 --- Certificate chain 0 s:/C=US/ST=State/L=City/O=Company/OU=ou1/CN=example.com i:/C=US/O=VeriSign, Inc./OU=VeriSign Trust Network/OU=Terms of use at https://www.verisign.com/rpa (c)10/CN=VeriSign Class 3 Secure Server CA - G3 --- Server certificate -----BEGIN CERTIFICATE----- <cert removed> -----END CERTIFICATE----- subject=/C=US/ST=State/L=City/O=Company/OU=ou1/CN=example.com issuer=/C=US/O=VeriSign, Inc./OU=VeriSign Trust Network/OU=Terms of use at https://www.verisign.com/rpa (c)10/CN=VeriSign Class 3 Secure Server CA - G3 --- No client certificate CA names sent --- SSL handshake has read 1563 bytes and written 435 bytes --- New, TLSv1/SSLv3, Cipher is RC4-SHA Server public key is 2048 bit Secure Renegotiation IS NOT supported Compression: NONE Expansion: NONE SSL-Session: Protocol : TLSv1 Cipher : RC4-SHA Session-ID: D65C4C6D52E183BF1E7543DA6D6A74EDD7D6E98EB7BD4D48450885188B127717 Session-ID-ctx: Master-Key: 253D4A3477FDED5FD1353D16C1F65CFCBFD78276B6DA1A078F19A51E9F79F7DAB4C7C98E5B8F308FC89C777519C887E2 Key-Arg : None Start Time: 1303258052 Timeout : 300 (sec) Verify return code: 0 (ok) --- QUIT DONE How can I get curl to verify this cert using the --capath option?

  Read the article

• IPV6 causing issue with DNS

  - by Mike Wells

  I have set up an 'internal' DNS at my work, basically we have ourdomain.com that is for internet, email etc and I have created on one of our linux network servers (debian) a DNS using bind9 with the domain ourdomain.inc. So based on my files below and the symptoms I'm describing; what effect could IPV6 be having on my setup? What can I do to fix this? I assume it is not actually the IPV6 causing the issue, but rather something in my setup. These are the critical (I think) files I have modified: named.conf.local zone "ourdomain.inc" { type master; file "/etc/bind/zones/ourdomain.inc.db"; }; zone "201.168.192.in-addr.arpa" { type master; file "/etc/bind/zones/rev.201.168.192.in-addr.arpa"; }; named.conf.options options { directory "/var/cache/bind"; // If there is a firewall between you and nameservers you want // to talk to, you may need to fix the firewall to allow multiple // ports to talk. See http://www.kb.cert.org/vuls/id/800113 // If your ISP provided one or more IP addresses for stable // nameservers, you probably want to use them as forwarders. // Uncomment the following block, and insert the addresses replacing // the all-0's placeholder. forwarders { 1.2.3.4; //IP of our external DNS provider }; auth-nxdomain no; # conform to RFC1035 listen-on-v6 { any; }; }; ourdomain.inc.db $TTL 86400 ourdomain.inc. IN SOA ns1.ipower.com. admin.ourdomain.inc. ( 2006081401 28800 3600 604800 38400 ) serv1 IN A 192.168.201.223 serv2 IN A 192.168.201.220 serv3 IN A 192.168.201.219 ns1.ipower.com. IN A 1.2.3.4 ns2.ipower.com. IN A 1.2.3.5 @ IN NS ns1.ipower.com. @ IN NS ns2.ipower.com. svn IN CNAME serv1 docs IN CNAME serv2 jira IN CNAME serv3 confluence IN CNAME serv3 fisheye IN CNAME serv3 rev.201.168.192.in-addr.arpa $TTL 86400 201.168.192.in-addr.arpa. IN SOA ns1.ipower.com. admin.ourdomain.inc. ( 2006081401; 28800; 604800; 604800; 86400 ) 223 IN PTR serv1 @ IN NS ns1.ipower.com. @ IN NS ns2.ipower.com. named.conf include "/etc/bind/named.conf.options"; include "/etc/bind/named.conf.local"; include "/etc/bind/named.conf.default-zones"; I then made our internal DNS my preferred DNS with the two external DNSs the next in-line. More the most part this seems to work, I can ping svn.ourdomain.inc and it resolves to the correct IP, I can also ping google.com and it also resolves no problem. So all seem good. However, periodically (couple of times a day at least), I loose the ability to ping the svn.domain.inc (and all others defined under the internal DNS). What seem to fix the issue temporarily is to disable IPV6 on the network adapter of the client machine and then re-enable it. Then it works for a bit but will always fail again. System Info Internal DNS Distributor ID: Debian Description: Debian GNU/Linux 6.0.6 (squeeze) Release: 6.0.6 Codename: squeeze Linux 2.6.32-5-686 i686 BIND 9.7.3 PC OS Name: Microsoft Windows 7 Professional OS Version: 6.1.7601 Service Pack 1 Build 7601 System Type: x64-based PC Network Card(s): 2 NIC(s) Installed. [01]: Realtek PCIe GBE Family Controller Connection Name: WORK LAN DHCP Enabled: No IP address(es) [01]: the.ipv4.address [02]: the:ipv6:address The question... So based on my files above and the symptoms I described; what effect could IPV6 be having on my setup? What can I do to fix this? I assume it is not actually the IPV6 causing the issue, but rather something in my setup.

  Read the article

• LXC Container Networking

  - by digitaladdictions

  I just started to experiment with LXC containers. I was able to create a container and start it up but I cannot get dhcp to assign the container an IP address. If I assign a static address the container can ping the host IP but not outside the host IP. The host is CentOS 6.5 and the guest is Ubuntu 14.04LTS. I used the template downloaded by lxc-create -t download -n cn-01 command. If I am trying to get an IP address on the same subnet as the host I don't believe I should need the IP tables rule for masquerading but I added it anyways. Same with IP forwarding. I compiled LXC by hand from the following source https://linuxcontainers.org/downloads/lxc-1.0.4.tar.gz Host Operating System Version #> cat /etc/redhat-release CentOS release 6.5 (Final) #> uname -a Linux localhost.localdomain 2.6.32-431.20.3.el6.x86_64 #1 SMP Thu Jun 19 21:14:45 UTC 2014 x86_64 x86_64 x86_64 GNU/Linux Container Config #> cat /usr/local/var/lib/lxc/cn-01/config # Template used to create this container: /usr/local/share/lxc/templates/lxc-download # Parameters passed to the template: # For additional config options, please look at lxc.container.conf(5) # Distribution configuration lxc.include = /usr/local/share/lxc/config/ubuntu.common.conf lxc.arch = x86_64 # Container specific configuration lxc.rootfs = /usr/local/var/lib/lxc/cn-01/rootfs lxc.utsname = cn-01 # Network configuration lxc.network.type = veth lxc.network.flags = up lxc.network.link = br0 LXC default.confu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether 00:0c:29:12:30:f2 brd ff:ff:ff:ff:f #> cat /usr/local/etc/lxc/default.conf lxc.network.type = veth lxc.network.link = br0 lxc.network.flags = up #> lxc-checkconfig Kernel configuration not found at /proc/config.gz; searching... Kernel configuration found at /boot/config-2.6.32-431.20.3.el6.x86_64 --- Namespaces --- Namespaces: enabled Utsname namespace: enabled Ipc namespace: enabled Pid namespace: enabled User namespace: enabled Network namespace: enabled Multiple /dev/pts instances: enabled --- Control groups --- Cgroup: enabled Cgroup namespace: enabled Cgroup device: enabled Cgroup sched: enabled Cgroup cpu account: enabled Cgroup memory controller: /usr/local/bin/lxc-checkconfig: line 103: [: too many arguments enabled Cgroup cpuset: enabled --- Misc --- Veth pair device: enabled Macvlan: enabled Vlan: enabled File capabilities: /usr/local/bin/lxc-checkconfig: line 118: [: -gt: unary operator expected Note : Before booting a new kernel, you can check its configuration usage : CONFIG=/path/to/config /usr/local/bin/lxc-checkconfig Network Config (HOST) #> cat /etc/sysconfig/network-scripts/ifcfg-br0 DEVICE=br0 TYPE=Bridge BOOTPROTO=dhcp ONBOOT=yes #> cat /etc/sysconfig/network-scripts/ifcfg-eth0 DEVICE=eth0 ONBOOT=yes TYPE=Ethernet IPV6INIT=no USERCTL=no BRIDGE=br0 #> cat /etc/networks default 0.0.0.0 loopback 127.0.0.0 link-local 169.254.0.0 #> ip a s 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether 00:0c:29:12:30:f2 brd ff:ff:ff:ff:ff:ff inet6 fe80::20c:29ff:fe12:30f2/64 scope link valid_lft forever preferred_lft forever 3: pan0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN link/ether 42:7e:43:b3:61:c5 brd ff:ff:ff:ff:ff:ff 4: br0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN link/ether 00:0c:29:12:30:f2 brd ff:ff:ff:ff:ff:ff inet 10.60.70.121/24 brd 10.60.70.255 scope global br0 inet6 fe80::20c:29ff:fe12:30f2/64 scope link valid_lft forever preferred_lft forever 12: vethT6BGL2: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether fe:a1:69:af:50:17 brd ff:ff:ff:ff:ff:ff inet6 fe80::fca1:69ff:feaf:5017/64 scope link valid_lft forever preferred_lft forever #> brctl show bridge name bridge id STP enabled interfaces br0 8000.000c291230f2 no eth0 vethT6BGL2 pan0 8000.000000000000 no #> cat /proc/sys/net/ipv4/ip_forward 1 # Generated by iptables-save v1.4.7 on Fri Jul 11 15:11:36 2014 *nat :PREROUTING ACCEPT [34:6287] :POSTROUTING ACCEPT [0:0] :OUTPUT ACCEPT [0:0] -A POSTROUTING -o eth0 -j MASQUERADE COMMIT # Completed on Fri Jul 11 15:11:36 2014 Network Config (Container) #> cat /etc/network/interfaces # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback auto eth0 iface eth0 inet dhcp #> ip a s 11: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether 02:69:fb:42:ee:d7 brd ff:ff:ff:ff:ff:ff inet6 fe80::69:fbff:fe42:eed7/64 scope link valid_lft forever preferred_lft forever 13: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo inet6 ::1/128 scope host valid_lft forever preferred_lft forever

  Read the article

• Mac 10.6 Universal Binary scipy: cephes/specfun "_aswfa_" symbol not found

  - by Markus

  Hi folks, I can't get scipy to function in 32 bit mode when compiled as a i386/x86_64 universal binary, and executed on my 64 bit 10.6.2 MacPro1,1. My python setup With the help of this answer, I built a 32/64 bit intel universal binary of python 2.6.4 with the intention of using the arch command to select between the architectures. (I managed to make some universal binaries of a few libraries I wanted using lipo.) That all works. I then installed scipy according to the instructions on hyperjeff's article, only with more up-to-date numpy (1.4.0) and skipping the bit about moving numpy aside briefly during the installation of scipy. Now, everything except scipy seems to be working as far as I can tell, and I can indeed select between 32 and 64 bit mode using arch -i386 python and arch -x86_64 python. The error Scipy complains in 32 bit mode: $ arch -x86_64 python -c "import scipy.interpolate; print 'success'" success $ arch -i386 python -c "import scipy.interpolate; print 'success'" Traceback (most recent call last): File "<string>", line 1, in <module> File "/Library/Frameworks/Python.framework/Versions/2.6/lib/python2.6/site-packages/scipy/interpolate/__init__.py", line 7, in <module> from interpolate import * File "/Library/Frameworks/Python.framework/Versions/2.6/lib/python2.6/site-packages/scipy/interpolate/interpolate.py", line 13, in <module> import scipy.special as spec File "/Library/Frameworks/Python.framework/Versions/2.6/lib/python2.6/site-packages/scipy/special/__init__.py", line 8, in <module> from basic import * File "/Library/Frameworks/Python.framework/Versions/2.6/lib/python2.6/site-packages/scipy/special/basic.py", line 8, in <module> from _cephes import * ImportError: dlopen(/Library/Frameworks/Python.framework/Versions/2.6/lib/python2.6/site-packages/scipy/special/_cephes.so, 2): Symbol not found: _aswfa_ Referenced from: /Library/Frameworks/Python.framework/Versions/2.6/lib/python2.6/site-packages/scipy/special/_cephes.so Expected in: flat namespace in /Library/Frameworks/Python.framework/Versions/2.6/lib/python2.6/site-packages/scipy/special/_cephes.so Attempt at tracking down the problem It looks like scipy.interpolate imports something called _cephes, which looks for a symbol called _aswfa_ but can't find it in 32 bit mode. Browsing through scipy's source, I find an ASWFA subroutine in specfun.f. The only scipy product file with a similar name is specfun.so, but both that and _cephes.so appear to be universal binaries: $ cd /Library/Frameworks/Python.framework/Versions/2.6/lib/python2.6/site-packages/scipy/special/ $ file _cephes.so specfun.so _cephes.so: Mach-O universal binary with 2 architectures _cephes.so (for architecture i386): Mach-O bundle i386 _cephes.so (for architecture x86_64): Mach-O 64-bit bundle x86_64 specfun.so: Mach-O universal binary with 2 architectures specfun.so (for architecture i386): Mach-O bundle i386 specfun.so (for architecture x86_64): Mach-O 64-bit bundle x86_64 Ho hum. I'm stuck. Things I may try but haven't figured out how yet include compiling specfun.so myself manually, somehow. I would imagine that scipy isn't broken for all 32 bit machines, so I guess something is wrong with the way I've installed it, but I can't figure out what. I don't really expect a full answer given my fairly unique (?) setup, but if anyone has any clues that might point me in the right direction, they'd be greatly appreciated. (edit) More details to address questions: I'm using gfortran (GNU Fortran from GCC 4.2.1 Apple Inc. build 5646). Python 2.6.4 was installed more-or-less like so: cd /tmp curl -O http://www.python.org/ftp/python/2.6.4/Python-2.6.4.tar.bz2 tar xf Python-2.6.4.tar.bz2 cd Python-2.6.4 # Now replace buggy pythonw.c file with one that supports the "arch" command: curl http://bugs.python.org/file14949/pythonw.c | sed s/2.7/2.6/ > Mac/Tools/pythonw.c ./configure --enable-framework=/Library/Frameworks --enable-universalsdk=/ --with-universal-archs=intel make -j4 sudo make frameworkinstall Scipy 0.7.1 was installed pretty much as described as here, but it boils down to a simple sudo python setup.py install. It would indeed appear that the symbol is undefined in the i386 architecture if you look at the _cephes library with nm, as suggested by David Cournapeau: $ nm -arch x86_64 /Library/Frameworks/Python.framework/Versions/2.6/lib/python2.6/site-packages/scipy/special/_cephes.so | grep _aswfa_ 00000000000d4950 T _aswfa_ 000000000011e4b0 d _oblate_aswfa_data 000000000011e510 d _oblate_aswfa_nocv_data (snip) $ nm -arch i386 /Library/Frameworks/Python.framework/Versions/2.6/lib/python2.6/site-packages/scipy/special/_cephes.so | grep _aswfa_ U _aswfa_ 0002e96c d _oblate_aswfa_data 0002e99c d _oblate_aswfa_nocv_data (snip) however, I can't yet explain its absence.

  Read the article

• "Launch Failed. Binary Not Found." Snow Leopard and Eclipse C/C++ IDE issue.

  - by Alex

  Not a question, I've just scoured the internet in search of a solution for this problem and thought I'd share it with the good folks of SO. I'll put it in plain terms so that it's accessible to newbs. :) (Apologies if this is the wrong place -- just trying to be helpful.) This issue occurs with almost any user OS X Snow Leopard who tries to use the Eclipse C/C++ IDE, but is particularly annoying for the people (like me) who were using the Eclipse C/C++ IDE in Leopard, and were unable to work with Eclipse anymore when they upgraded. The issue occurs When users go to build/compile/link their software. They get the following error: Launch Failed. Binary Not Found. Further, the "binaries" branch in the project window on the left is simply nonexistent. THE PROBLEM: is that GCC 4.2 (the GNU Compiler Collection) that comes with Snow Leopard compiles binaries in 64-bit by default. Unfortunately, the linker that Eclipse uses does not understand 64-bit binaries; it reads 32-bit binaries. There may be other issues here, but in short, they culminate in no binary being generated, at least not one that Eclipse can read, which translates into Eclipse not finding the binaries. Hence the error. One solution is to add an -arch i686 flag when making the file, but manually making the file every time is annoying. Luckily for us, Snow Leopard also comes with GCC 4.0, which compiles in 32 bits by default. So one solution is merely to link this as the default compiler. This is the way I did it. THE SOLUTION: The GCCs are in /usr/bin, which is normally a hidden folder, so you can't see it in the Finder unless you explicitly tell the system that you want to see hidden folders. Anyway, what you want to do is go to the /usr/bin folder and delete the path that links the GCC command with GCC 4.2 and add a path that links the GCC command with GCC 4.0. In other words, when you or Eclipse try to access GCC, we want the command to go to the compiler that builds in 32 bits by default, so that the linker can read the files; we do not want it to go to the compiler that compiles in 64 bits. The best way to do this is to go to Applications/Utilities, and select the app called Terminal. A text prompt should come up. It should say something like "(Computer Name):~ (Username)$ " (with a space for you user input at the end). The way to accomplish the tasks above is to enter the following commands, entering each one in sequence VERBATIM, and pressing enter after each individual line. cd /usr/bin rm cc gcc c++ g++ ln -s gcc-4.0 cc ln -s gcc-4.0 gcc ln -s c++-4.0 c++ ln -s g++-4.0 g++ Like me, you will probably get an error that tells you you don't have permission to access these files. If so, try the following commands instead: cd /usr/bin sudo rm cc gcc c++ g++ sudo ln -s gcc-4.0 cc sudo ln -s gcc-4.0 gcc sudo ln -s c++-4.0 c++ sudo ln -s g++-4.0 g++ Sudo may prompt you for a password. If you've never used sudo before, try just pressing enter. If that doesn't work, try the password for your main admin account. OTHER POSSIBLE SOLUTIONS You may be able to enter build variables into Eclipse. I tried this, but I don't know enough about it. If you want to feel it out, the flag you will probably need is -arch i686. In earnest, GCC-4.0 worked for me all this time, and I don't see any reason to switch now. There may be a way to alter the default for the compiler itself, but once again, I don't know enough about it. Hope this has been helpful and informative. Good coding!

  Read the article

• Serial Port Not getting closed. I want to release the COM port ...

  - by sunil

  Serial Port Not getting closed. I want to release the COM port ... Below is my code.... import java.io.*; import java.util.*; import gnu.io.*; public class ReadCommPort implements SerialPortEventListener { static CommPortIdentifier portId; static Enumeration portList; InputStream inputStream; OutputStream outputStream; public SerialPort serialPort; List byteList = new ArrayList(); public static Message message = null; public void readData() { boolean portFound = false; String defaultPort = "COM1"; portList = CommPortIdentifier.getPortIdentifiers(); while ( portList.hasMoreElements() ) { portId = ( CommPortIdentifier )portList.nextElement(); if ( portId.getPortType() == CommPortIdentifier.PORT_SERIAL ) { if ( portId.getName().equals( defaultPort ) ) { System.out.println( "Found port: " + defaultPort ); portFound = true; buildSerialPort(); } } } if ( ! portFound ) { System.out.println( "port " + defaultPort + " not found." ); } } public void buildSerialPort() { try { serialPort = (SerialPort) portId.open( "ReadCommPort", 1 ); inputStream = serialPort.getInputStream(); outputStream = serialPort.getOutputStream(); serialPort.addEventListener( this ); serialPort.notifyOnDataAvailable(true); serialPort.setSerialPortParams( 2400, SerialPort.DATABITS_7, SerialPort.STOPBITS_1, SerialPort.PARITY_NONE ); } catch ( Exception e ) { e.printStackTrace(); } } @SuppressWarnings("unchecked") public void serialEvent( SerialPortEvent event ) { switch ( event.getEventType() ) { case SerialPortEvent.BI: System.out.println( "BI"); break; case SerialPortEvent.OE: System.out.println( "OE"); break; case SerialPortEvent.FE: System.out.println( "FE"); break; case SerialPortEvent.PE: System.out.println( "PE"); break; case SerialPortEvent.CD: System.out.println( "CD"); break; case SerialPortEvent.CTS: System.out.println( "CTS"); break; case SerialPortEvent.DSR: System.out.println( "DSR"); break; case SerialPortEvent.RI: System.out.println( "RI"); break; case SerialPortEvent.OUTPUT_BUFFER_EMPTY: System.out.println( "OUTPUT_BUFFER_EMPTY"); break; case SerialPortEvent.DATA_AVAILABLE : try { int len = inputStream.available(); byte[] readBuffer = new byte[ len ]; // processing data code.. // close the port // release all resources... serialPort.removeEventListener(); try { serialPort.addEventListener( null ); } catch (TooManyListenersException e) { e.printStackTrace(); } inputStream.close(); outputStream.close(); serialPort.close(); } catch ( IOException e ) { e.printStackTrace(); } break; } } public static void main(String[] args) { new ReadCommPort().readData(); } }

  Read the article

• How to install PyQt on Mac OS X 10.6.

  - by Jebagnanadas

  Hello all, I'm quite new to Mac OS X. when i tried to install PyQt on Mac Os X after installing python 3.1, Qt 4.6.2 and SIP 4.10.1 i encounter the following error when i execute $python3 configure.py command. Determining the layout of your Qt installation... This is the GPL version of PyQt 4.7 (licensed under the GNU General Public License) for Python 3.1 on darwin. Type '2' to view the GPL v2 license. Type '3' to view the GPL v3 license. Type 'yes' to accept the terms of the license. Type 'no' to decline the terms of the license. Do you accept the terms of the license? yes Checking to see if the QtGui module should be built... Checking to see if the QtHelp module should be built... Checking to see if the QtMultimedia module should be built... Checking to see if the QtNetwork module should be built... Checking to see if the QtOpenGL module should be built... Checking to see if the QtScript module should be built... Checking to see if the QtScriptTools module should be built... Checking to see if the QtSql module should be built... Checking to see if the QtSvg module should be built... Checking to see if the QtTest module should be built... Checking to see if the QtWebKit module should be built... Checking to see if the QtXml module should be built... Checking to see if the QtXmlPatterns module should be built... Checking to see if the phonon module should be built... Checking to see if the QtAssistant module should be built... Checking to see if the QtDesigner module should be built... Qt v4.6.2 free edition is being used. Qt is built as a framework. SIP 4.10.1 is being used. The Qt header files are in /usr/include. The shared Qt libraries are in /Library/Frameworks. The Qt binaries are in /Developer/Tools/Qt. The Qt mkspecs directory is in /usr/local/Qt4.6. These PyQt modules will be built: QtCore. The PyQt Python package will be installed in /Library/Frameworks/Python.framework/Versions/3.1/lib/python3.1/site-packages. PyQt is being built with generated docstrings. PyQt is being built with 'protected' redefined as 'public'. The Designer plugin will be installed in /Developer/Applications/Qt/plugins/designer. The PyQt .sip files will be installed in /Library/Frameworks/Python.framework/Versions/3.1/share/sip/PyQt4. pyuic4, pyrcc4 and pylupdate4 will be installed in /Library/Frameworks/Python.framework/Versions/3.1/bin. Generating the C++ source for the QtCore module... sip: Usage: sip [-h] [-V] [-a file] [-b file] [-c dir] [-d file] [-e] [-g] [-I dir] [-j #] [-k] [-m file] [-o] [-p module] [-r] [-s suffix] [-t tag] [-w] [-x feature] [-z file] [file] Error: Unable to create the C++ code. Anybody here installed PyQt on Mac OS X 10.6.2 successfully.. Any help would be much appreciated.. Thanks in advance..

  Read the article

• issue with std::advance on std::sets

  - by tim

  I've stumbled upon what I believe is a bug in the stl algorithm advance. When I'm advancing the iterator off of the end of the container, I get inconsistent results. Sometimes I get container.end(), sometimes I get the last element. I've illustrated this with the following code: #include <algorithm> #include <cstdio> #include <set> using namespace std; typedef set<int> tMap; int main(int argc, char** argv) { tMap::iterator i; tMap the_map; for (int i=0; i<10; i++) the_map.insert(i); #if EXPERIMENT==1 i = the_map.begin(); #elif EXPERIMENT==2 i = the_map.find(4); #elif EXPERIMENT==3 i = the_map.find(5); #elif EXPERIMENT==4 i = the_map.find(6); #elif EXPERIMENT==5 i = the_map.find(9); #elif EXPERIMENT==6 i = the_map.find(2000); #else i = the_map.end(); #endif advance(i, 100); if (i == the_map.end()) printf("the end\n"); else printf("wuh? %d\n", *i); return 0; } Which I get the following unexpected (according to me) behavior in experiment 3 and 5 where I get the last element instead of the_map.end(). [tim@saturn advance]$ uname -srvmpio Linux 2.6.18-1.2798.fc6 #1 SMP Mon Oct 16 14:37:32 EDT 2006 i686 athlon i386 GNU/Linux [tim@saturn advance]$ g++ --version g++ (GCC) 4.1.1 20061011 (Red Hat 4.1.1-30) Copyright (C) 2006 Free Software Foundation, Inc. This is free software; see the source for copying conditions. There is NO warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. [tim@saturn advance]$ g++ -DEXPERIMENT=1 advance.cc [tim@saturn advance]$ ./a.out the end [tim@saturn advance]$ g++ -DEXPERIMENT=2 advance.cc [tim@saturn advance]$ ./a.out the end [tim@saturn advance]$ g++ -DEXPERIMENT=3 advance.cc [tim@saturn advance]$ ./a.out wuh? 9 [tim@saturn advance]$ g++ -DEXPERIMENT=4 advance.cc [tim@saturn advance]$ ./a.out the end [tim@saturn advance]$ g++ -DEXPERIMENT=5 advance.cc [tim@saturn advance]$ ./a.out wuh? 9 [tim@saturn advance]$ g++ -DEXPERIMENT=6 advance.cc [tim@saturn advance]$ ./a.out the end [tim@saturn advance]$ g++ -DEXPERIMENT=7 advance.cc [tim@saturn advance]$ ./a.out the end [tim@saturn advance]$ From the sgi website (see link at top), it has the following example: list<int> L; L.push_back(0); L.push_back(1); list<int>::iterator i = L.begin(); advance(i, 2); assert(i == L.end()); I would think that the assertion should apply to other container types, no? What am I missing? Thanks!

  Read the article

• Running 32 bit assembly code on a 64 bit Linux & 64 bit Processor : Explain the anomaly.

  - by claws

  Hello, I'm in an interesting problem.I forgot I'm using 64bit machine & OS and wrote a 32 bit assembly code. I don't know how to write 64 bit code. This is the x86 32-bit assembly code for Gnu Assembler (AT&T syntax) on Linux. //hello.S #include <asm/unistd.h> #include <syscall.h> #define STDOUT 1 .data hellostr: .ascii "hello wolrd\n"; helloend: .text .globl _start _start: movl $(SYS_write) , %eax //ssize_t write(int fd, const void *buf, size_t count); movl $(STDOUT) , %ebx movl $hellostr , %ecx movl $(helloend-hellostr) , %edx int $0x80 movl $(SYS_exit), %eax //void _exit(int status); xorl %ebx, %ebx int $0x80 ret Now, This code should run fine on a 32bit processor & 32 bit OS right? As we know 64 bit processors are backward compatible with 32 bit processors. So, that also wouldn't be a problem. The problem arises because of differences in system calls & call mechanism in 64-bit OS & 32-bit OS. I don't know why but they changed the system call numbers between 32-bit linux & 64-bit linux. asm/unistd_32.h defines: #define __NR_write 4 #define __NR_exit 1 asm/unistd_64.h defines: #define __NR_write 1 #define __NR_exit 60 Anyway using Macros instead of direct numbers is paid off. Its ensuring correct system call numbers. when I assemble & link & run the program. $cpp hello.S hello.s //pre-processor $as hello.s -o hello.o //assemble $ld hello.o // linker : converting relocatable to executable Its not printing helloworld. In gdb its showing: Program exited with code 01. I don't know how to debug in gdb. using tutorial I tried to debug it and execute instruction by instruction checking registers at each step. its always showing me "program exited with 01". It would be great if some on could show me how to debug this. (gdb) break _start Note: breakpoint -10 also set at pc 0x4000b0. Breakpoint 8 at 0x4000b0 (gdb) start Function "main" not defined. Make breakpoint pending on future shared library load? (y or [n]) y Temporary breakpoint 9 (main) pending. Starting program: /home/claws/helloworld Program exited with code 01. (gdb) info breakpoints Num Type Disp Enb Address What 8 breakpoint keep y 0x00000000004000b0 <_start> 9 breakpoint del y <PENDING> main I tried running strace. This is its output: execve("./helloworld", ["./helloworld"], [/* 39 vars */]) = 0 write(0, NULL, 12 <unfinished ... exit status 1> Explain the parameters of write(0, NULL, 12) system call in the output of strace? What exactly is happening? I want to know the reason why exactly its exiting with exitstatus=1? Can some one please show me how to debug this program using gdb? Why did they change the system call numbers? Kindly change this program appropriately so that it can run correctly on this machine. EDIT: After reading Paul R's answer. I checked my files claws@claws-desktop:~$ file ./hello.o ./hello.o: ELF 64-bit LSB relocatable, x86-64, version 1 (SYSV), not stripped claws@claws-desktop:~$ file ./hello ./hello: ELF 64-bit LSB executable, x86-64, version 1 (SYSV), statically linked, not stripped All of my questions still hold true. What exactly is happening in this case? Can someone please answer my questions and provide an x86-64 version of this code?

  Read the article

• Running 32 bit assembly code on a 64 bit Linux & 64 bit Processor : Expalin the anomaly.

  - by claws

  Hello, I'm in an interesting problem.I forgot I'm using 64bit machine & OS and wrote a 32 bit assembly code. I don't know how to write 64 bit code. This is the x86 32-bit assembly code for Gnu Assembler (AT&T syntax) on Linux. #include <asm/unistd.h> #include <syscall.h> #define STDOUT 1 .data hellostr: .ascii "hello wolrd\n"; helloend: .text .globl _start _start: movl $(SYS_write) , %eax //ssize_t write(int fd, const void *buf, size_t count); movl $(STDOUT) , %ebx movl $hellostr , %ecx movl $(helloend-hellostr) , %edx int $0x80 movl $(SYS_exit), %eax //void _exit(int status); xorl %ebx, %ebx int $0x80 ret Now, This code should run fine on a 32bit processor & 32 bit OS right? As we know 64 bit processors are backward compatible with 32 bit processors. So, that also wouldn't be a problem. The problem arises because of differences in system calls & call mechanism in 64-bit OS & 32-bit OS. I don't know why but they changed the system call numbers between 32-bit linux & 64-bit linux. asm/unistd_32.h defines: #define __NR_write 4 #define __NR_exit 1 asm/unistd_64.h defines: #define __NR_write 1 #define __NR_exit 60 Anyway using Macros instead of direct numbers is paid off. Its ensuring correct system call numbers. when I assemble & link & run the program. Its not printing helloworld. In gdb its showing: Program exited with code 01. I don't know how to debug in gdb. using tutorial I tried to debug it and execute instruction by instruction checking registers at each step. its always showing me "program exited with 01". It would be great if some on could show me how to debug this. (gdb) break _start Note: breakpoint -10 also set at pc 0x4000b0. Breakpoint 8 at 0x4000b0 (gdb) start Function "main" not defined. Make breakpoint pending on future shared library load? (y or [n]) y Temporary breakpoint 9 (main) pending. Starting program: /home/claws/helloworld Program exited with code 01. (gdb) info breakpoints Num Type Disp Enb Address What 8 breakpoint keep y 0x00000000004000b0 <_start> 9 breakpoint del y <PENDING> main I tried running strace. This is its output: execve("./helloworld", ["./helloworld"], [/* 39 vars */]) = 0 write(0, NULL, 12 <unfinished ... exit status 1> Explain the parameters of write(0, NULL, 12) system call in the output of strace? What exactly is happening? I want to know the reason why exactly its exiting with exitstatus=1? Can some one please show me how to debug this program using gdb? Why did they change the system call numbers? Change this program appropriately so that it can run correctly on this machine.

  Read the article

• Java Refuses to Start - Could not reserve enough space for object heap

  - by Randyaa

  Background We have a pool of aproximately 20 linux blades. Some are running Suse, some are running Redhat. ALL share NAS space which contains the following 3 folders: /NAS/app/java - a symlink that points to an installation of a Java JDK. Currently version 1.5.0_10 /NAS/app/lib - a symlink that points to a version of our application. /NAS/data - directory where our output is written All our machines have 2 processors (hyperthreaded) with 4gb of physical memory and 4gb of swap space. We limit the number of 'jobs' each machine can process at a given time to 6 (this number likely needs to change, but that does not enter into the current problem so please ignore it for the time being). Some of our jobs set a Max Heap size of 512mb, some others reserve a Max Heap size of 2048mb. Again, we realize we could go over our available memory if 6 jobs started on the same machine with the heap size set to 2048, but to our knowledge this has not yet occurred. The Problem Once and a while a Job will fail immediately with the following message: Error occurred during initialization of VM Could not reserve enough space for object heap Could not create the Java virtual machine. We used to chalk this up to too many jobs running at the same time on the same machine. The problem happened infrequently enough (MAYBE once a month) that we'd just restart it and everything would be fine. The problem has recently gotten much worse. All of our jobs which request a max heap size of 2048m fail immediately almost every time and need to get restarted several times before completing. We've gone out to individual machines and tried executing them manually with the same result. Debugging It turns out that the problem only exists for our SuSE boxes. The reason it has been happening more frequently is becuase we've been adding more machines, and the new ones are SuSE. 'cat /proc/version' on the SuSE boxes give us: Linux version 2.6.5-7.244-bigsmp (geeko@buildhost) (gcc version 3.3.3 (SuSE Linux)) #1 SMP Mon Dec 12 18:32:25 UTC 2005 'cat /proc/version' on the RedHat boxes give us: Linux version 2.4.21-32.0.1.ELsmp ([email protected]) (gcc version 3.2.3 20030502 (Red Hat Linux 3.2.3-52)) #1 SMP Tue May 17 17:52:23 EDT 2005 'uname -a' gives us the following on BOTH types of machines: UTC 2005 i686 i686 i386 GNU/Linux No jobs are running on the machine, and no other processes are utilizing much memory. All of the processes currently running might be using 100mb total. 'top' currently shows the following: Mem: 4146528k total, 3536360k used, 610168k free, 132136k buffers Swap: 4194288k total, 0k used, 4194288k free, 3283908k cached 'vmstat' currently shows the following: procs -----------memory---------- ---swap-- -----io---- --system-- ----cpu---- r b swpd free buff cache si so bi bo in cs us sy id wa 0 0 0 610292 132136 3283908 0 0 0 2 26 15 0 0 100 0 If we kick off a job with the following command line (Max Heap of 1850mb) it starts fine: java/bin/java -Xmx1850M -cp helloworld.jar HelloWorld Hello World If we bump up the max heap size to 1875mb it fails: java/bin/java -Xmx1875M -cp helloworld.jar HelloWorld Error occurred during initialization of VM Could not reserve enough space for object heap Could not create the Java virtual machine. It's quite clear that the memory currently being used is for Buffering/Caching and that's why so little is being displayed as 'free'. What isn't clear is why there is a magical 1850mb line where anything higher means Java can't start. Any explanations would be greatly appreciated.

  Read the article

• mysql_close doesn't kill locked sql requests

  - by Nikita

  I use mysqld Ver 5.1.37-2-log for debian-linux-gnu I perform mysql calls from c++ code with functions mysql_query. The problem occurs when mysql_query execute procedure, procedure locked on locked table, so mysql_query hangs. If send kill signal to application then we can see lock until table is locked. Create the following SQL table and procedure CREATE TABLE IF NOT EXISTS `tabletolock` ( `id` INT NOT NULL AUTO_INCREMENT, PRIMARY KEY (`id`) )ENGINE = InnoDB; DELIMITER $$ DROP PROCEDURE IF EXISTS `LOCK_PROCEDURE` $$ CREATE PROCEDURE `LOCK_PROCEDURE`() BEGIN SELECT id INTO @id FROM tabletolock; END $$ DELOMITER; There are sql commands to reproduce the problem: 1. in one terminal execute lock tables tabletolock write; 2. in another terminal execute call LOCK_PROCEDURE(); 3. In first terminal exeute show processlist and see | 2492 | root | localhost | syn_db | Query | 12 | Locked | SELECT id INTO @id FROM tabletolock | Then perfrom Ctrl-C in second terminal to interrupt our procudere and see processlist again. It is not changed, we already see locked select request and can teminate it by unlock tables or kill commands. Problem described is occured with mysql command line client. Also such problem exists when we use functions mysql_query and mysql_close. Example of c code: #include <iostream> #include <mysql/mysql.h> #include <mysql/errmsg.h> #include <signal.h> // g++ -Wall -g -fPIC -lmysqlclient dbtest.cpp using namespace std; MYSQL * connection = NULL; void closeconnection() { if(connection != NULL) { cout << "close connection !\n"; mysql_close(connection); mysql_thread_end(); delete connection; mysql_library_end(); } } void sigkill(int s) { closeconnection(); signal(SIGINT, NULL); raise(s); } int main(int argc, char ** argv) { signal(SIGINT, sigkill); connection = new MYSQL; mysql_init(connection); mysql_options(connection, MYSQL_READ_DEFAULT_GROUP, "nnfc"); if (!mysql_real_connect(connection, "127.0.0.1", "user", "password", "db", 3306, NULL, CLIENT_MULTI_RESULTS)) { delete connection; cout << "cannot connect\n"; return -1; } cout << "before procedure call\n"; mysql_query(connection, "CALL LOCK_PROCEDURE();"); cout << "after procedure call\n"; closeconnection(); return 0; } Compile it, and perform the folloing actions: 1. in first terminal local tables tabletolock write; 2. run program ./a.out 3. interrupt program Ctrl-C. on the screen we see that closeconnection function is called, so connection is closed. 4. in first terminal execute show processlist and see that procedure was not intrrupted. My question is how to terminate such locked calls from c code? Thank you in advance!

  Read the article

• hello-1.mod.c:14: warning: missing initializer (near initialization for '__this_module.arch.unw_sec_init')

  - by Sompom

  I am trying to write a module for an sbc1651. Since the device is ARM, this requires a cross-compile. As a start, I am trying to compile the "Hello Kernel" module found here. This compiles fine on my x86 development system, but when I try to cross-compile I get the below error. /home/developer/HelloKernel/hello-1.mod.c:14: warning: missing initializer /home/developer/HelloKernel/hello-1.mod.c:14: warning: (near initialization for '__this_module.arch.unw_sec_init') Since this is in the .mod.c file, which is autogenerated I have no idea what's going on. The mod.c file seems to be generated by the module.h file. As far as I can tell, the relevant parts are the same between my x86 system's module.h and the arm kernel header's module.h. Adding to my confusion, this problem is either not googleable (by me...) or hasn't happened to anyone before. Or I'm just doing something clueless that anyone with any sense wouldn't do. The cross-compiler I'm using was supplied by Freescale (I think). I suppose it could be a problem with the compiler. Would it be worth trying to build the toolchain myself? Obviously, since this is a warning, I could ignore it, but since it's so strange, I am worried about it, and would like to at least know the cause... Thanks very much, Sompom Here are the source files hello-1.mod.c #include <linux/module.h> #include <linux/vermagic.h> #include <linux/compiler.h> MODULE_INFO(vermagic, VERMAGIC_STRING); struct module __this_module __attribute__((section(".gnu.linkonce.this_module"))) = { .name = KBUILD_MODNAME, .init = init_module, #ifdef CONFIG_MODULE_UNLOAD .exit = cleanup_module, #endif .arch = MODULE_ARCH_INIT, }; static const struct modversion_info ____versions[] __used __attribute__((section("__versions"))) = { { 0x3972220f, "module_layout" }, { 0xefd6cf06, "__aeabi_unwind_cpp_pr0" }, { 0xea147363, "printk" }, }; static const char __module_depends[] __used __attribute__((section(".modinfo"))) = "depends="; hello-1.c (modified slightly from the given link) /* hello-1.c - The simplest kernel module. * * Copyright (C) 2001 by Peter Jay Salzman * * 08/02/2006 - Updated by Rodrigo Rubira Branco <[email protected]> */ /* Kernel Programming */ #ifndef MODULE #define MODULE #endif #ifndef LINUX #define LINUX #endif #ifndef __KERNEL__ #define __KERNEL__ #endif #include <linux/module.h> /* Needed by all modules */ #include <linux/kernel.h> /* Needed for KERN_ALERT */ static int hello_init_module(void) { printk(KERN_ALERT "Hello world 1.\n"); /* A non 0 return means init_module failed; module can't be loaded.*/ return 0; } static void hello_cleanup_module(void) { printk(KERN_ALERT "Goodbye world 1.\n"); } module_init(hello_init_module); module_exit(hello_cleanup_module); MODULE_LICENSE("GPL"); Makefile export ARCH:=arm export CCPREFIX:=/opt/freescale/usr/local/gcc-4.4.4-glibc-2.11.1-multilib-1.0/arm-fsl-linux-gnueabi/bin/arm-linux- export CROSS_COMPILE:=${CCPREFIX} TARGET := hello-1 WARN := -W -Wall -Wstrict-prototypes -Wmissing-prototypes -Wno-sign-compare -Wno-unused -Werror UNUSED_FLAGS := -std=c99 -pedantic EXTRA_CFLAGS := -O2 -DMODULE -D__KERNEL__ ${WARN} ${INCLUDE} KDIR ?= /home/developer/src/ltib-microsys/ltib/rpm/BUILD/linux-2.6.35.3 ifneq ($(KERNELRELEASE),) # kbuild part of makefile obj-m := $(TARGET).o else # normal makefile default: clean $(MAKE) -C $(KDIR) M=$$PWD .PHONY: clean clean: -rm built-in.o -rm $(TARGET).ko -rm $(TARGET).ko.unsigned -rm $(TARGET).mod.c -rm $(TARGET).mod.o -rm $(TARGET).o -rm modules.order -rm Module.symvers endif

  Read the article

• How to reduce virtual memory by optimising my PHP code?

  - by iCeR

  My current code (see below) uses 147MB of virtual memory! My provider has allocated 100MB by default and the process is killed once run, causing an internal error. The code is utilising curl multi and must be able to loop with more than 150 iterations whilst still minimizing the virtual memory. The code below is only set at 150 iterations and still causes the internal server error. At 90 iterations the issue does not occur. How can I adjust my code to lower the resource use / virtual memory? Thanks! <?php function udate($format, $utimestamp = null) { if ($utimestamp === null) $utimestamp = microtime(true); $timestamp = floor($utimestamp); $milliseconds = round(($utimestamp - $timestamp) * 1000); return date(preg_replace('`(?<!\\\\)u`', $milliseconds, $format), $timestamp); } $url = 'https://www.testdomain.com/'; $curl_arr = array(); $master = curl_multi_init(); for($i=0; $i<150; $i++) { $curl_arr[$i] = curl_init(); curl_setopt($curl_arr[$i], CURLOPT_URL, $url); curl_setopt($curl_arr[$i], CURLOPT_RETURNTRANSFER, 1); curl_setopt($curl_arr[$i], CURLOPT_SSL_VERIFYHOST, FALSE); curl_setopt($curl_arr[$i], CURLOPT_SSL_VERIFYPEER, FALSE); curl_multi_add_handle($master, $curl_arr[$i]); } do { curl_multi_exec($master,$running); } while($running > 0); for($i=0; $i<150; $i++) { $results = curl_multi_getcontent ($curl_arr[$i]); $results = explode("<br>", $results); echo $results[0]; echo "<br>"; echo $results[1]; echo "<br>"; echo udate('H:i:s:u'); echo "<br><br>"; usleep(100000); } ?> Processor Information Total processors: 8 Processor #1 Vendor GenuineIntel Name Intel(R) Xeon(R) CPU E5405 @ 2.00GHz Speed 1995.120 MHz Cache 6144 KB Processor #2 Vendor GenuineIntel Name Intel(R) Xeon(R) CPU E5405 @ 2.00GHz Speed 1995.120 MHz Cache 6144 KB Processor #3 Vendor GenuineIntel Name Intel(R) Xeon(R) CPU E5405 @ 2.00GHz Speed 1995.120 MHz Cache 6144 KB Processor #4 Vendor GenuineIntel Name Intel(R) Xeon(R) CPU E5405 @ 2.00GHz Speed 1995.120 MHz Cache 6144 KB Processor #5 Vendor GenuineIntel Name Intel(R) Xeon(R) CPU E5405 @ 2.00GHz Speed 1995.120 MHz Cache 6144 KB Processor #6 Vendor GenuineIntel Name Intel(R) Xeon(R) CPU E5405 @ 2.00GHz Speed 1995.120 MHz Cache 6144 KB Processor #7 Vendor GenuineIntel Name Intel(R) Xeon(R) CPU E5405 @ 2.00GHz Speed 1995.120 MHz Cache 6144 KB Processor #8 Vendor GenuineIntel Name Intel(R) Xeon(R) CPU E5405 @ 2.00GHz Speed 1995.120 MHz Cache 6144 KB Memory Information Memory for crash kernel (0x0 to 0x0) notwithin permissible range Memory: 8302344k/9175040k available (2176k kernel code, 80272k reserved, 901k data, 228k init, 7466304k highmem) System Information Linux server3.server.com 2.6.18-194.17.1.el5PAE #1 SMP Wed Sep 29 13:31:51 EDT 2010 i686 i686 i386 GNU/Linux Physical Disks SCSI device sda: 1952448512 512-byte hdwr sectors (999654 MB) sda: Write Protect is off sda: Mode Sense: 03 00 00 08 SCSI device sda: drive cache: write back SCSI device sda: 1952448512 512-byte hdwr sectors (999654 MB) sda: Write Protect is off sda: Mode Sense: 03 00 00 08 SCSI device sda: drive cache: write back sd 0:1:0:0: Attached scsi disk sda sd 4:0:0:0: Attached scsi removable disk sdb sd 0:1:0:0: Attached scsi generic sg4 type 0 sd 4:0:0:0: Attached scsi generic sg7 type 0 Current Memory Usage total used free shared buffers cached Mem: 8306672 7847384 459288 0 487912 6444548 -/+ buffers/cache: 914924 7391748 Swap: 4095992 496 4095496 Total: 12402664 7847880 4554784 Current Disk Usage Filesystem Size Used Avail Use% Mounted on /dev/mapper/VolGroup00-LogVol00 898G 307G 546G 36% / /dev/sda1 99M 19M 76M 20% /boot none 4.0G 0 4.0G 0% /dev/shm /var/tmpMnt 4.0G 1.8G 2.0G 48% /tmp

  Read the article

• wordexp followed by strcpy = EXC_BAD_ACCESS + sharedlibrary apply-load-rules-all

  - by fyngyrz

  The implication is a memory problem. I have static allocations for these: char akdir[400]; char homedir[400]; This crashes on the first strcpy(): void setuplibfoo() { long ii; double x; wordexp_t result; // This obtains the user's home directory // -------------------------------------- homedir[0]=0; // in case wordexp fails switch (wordexp("~/",&result,0)) { case 0: // Successful. We'll fall into deallocate when done. { strcpy(homedir,result.we_wordv[0]); // <<--- CRASH! strcpy(akdir,homedir); strcat(akdir,"ak-plugins/"); vs_status(akdir); } case WRDE_NOSPACE: // If the error was WRDE_NOSPACE, then { // perhaps part of the result was allocated. wordfree (&result); } default: // all other errors do not require deallocation { break; } } ...additional code clipped.. doesn't get there on crash. This is in a shared library I've written that is linked to my application, also something I've written. In this case, it doesn't get very far, although if it starts, it's fine. ...I've read the wordexp docs several times; they say they allocate new objects, so you just set up that type and call them with the address. The switch error model is right from the wordexp docs: http://www.gnu.org/s/libc/manual/html_mono/libc.html#Wordexp-Example It doesn't always crash. Just sometimes, and just under 10.6. Never under 10.5 I'm building debug mode with XCode 3.1.1, under OSX 10.5.8 it seems to run ok, I've not seen a crash -- under 10.6, it crashes... sometimes. But always with that same exception, and always in the same place. The Google has it that this actually means, somehow, that it's too soon to allocate memory. But all the instances I could find were memory errors on the part of the programmer. Overruns, etc. And I can't find any docs on when it IS safe to allocate memory. Now, the path that expands there is nowhere near 400 characters. it's this (it it completes): /Users/flake/ak-plugins/ and this: /Users/flake/ ...if it doesn't. the strcpy... copies 2nd param to first. Theirs to mine. And it works! under 10.5. :/ So is wordexp broke? Is 10.6 broke? Am I cRaZy? Here's the debugger output: 0x00013446 <+0049> call 0xc98da <dyld_stub_wordexp> 0x0001344b <+0054> test %eax,%eax 0x0001344d <+0056> je 0x13454 <setuplibfoo+63> 0x0001344f <+0058> jmp 0x134da <setuplibfoo+197> 0x00013454 <+0063> mov -0x1c(%ebp),%eax 0x00013457 <+0066> mov (%eax),%eax 0x00013459 <+0068> mov %eax,0x4(%esp) 0x0001345d <+0072> lea 0xb6cc2(%ebx),%eax 0x00013463 <+0078> mov (%eax),%eax 0x00013465 <+0080> mov %eax,(%esp) 0x00013468 <+0083> call 0xc9898 <dyld_stub_strcpy> 0x0001346d <+0088> lea 0xb6cc2(%ebx),%eax <<--CRASH!

  Read the article

• xts error - order.by requires an appropriate time-based object

  - by Samo

  I can not resolve why error in simple creation of xts object xts(rep(0, NROW(TICK.NYSE)), order.by = index(TICK.NYSE)) Error in xts(rep(0, NROW(TICK.NYSE)), order.by = index(TICK.NYSE)) : order.by requires an appropriate time-based object appeared while this was working perfectly 14 days ago when I last used the same code (since then the only difference is that TICK.NYSE grow in length since data was added since then). More details below: > Sys.getenv("TZ") [1] "EST" > tail(xts(rep(0, NROW(TICK.NYSE)), order.by = index(TICK.NYSE))) Error in xts(rep(0, NROW(TICK.NYSE)), order.by = index(TICK.NYSE)) : order.by requires an appropriate time-based object > class(index(TICK.NYSE["T09:30/T09:31"])) [1] "POSIXct" > tail(xts(rep(0, NROW(tail(TICK.NYSE))), order.by = index(tail(TICK.NYSE)))) Error in xts(rep(0, NROW(tail(TICK.NYSE))), order.by = index(tail(TICK.NYSE))) : order.by requires an appropriate time-based object > tail(TICK.NYSE) TICK-NYSE.Open TICK-NYSE.High TICK-NYSE.Low TICK-NYSE.Close 2012-03-15 14:54:00 -278 -89 -299 -89 2012-03-15 14:55:00 -89 427 -89 201 2012-03-15 14:56:00 201 318 30 234 2012-03-15 14:57:00 234 242 -222 -64 2012-03-15 14:58:00 -64 346 -82 346 2012-03-15 14:59:00 346 525 36 525 TICK-NYSE.Volume TICK-NYSE.WAP TICK-NYSE.hasGaps 2012-03-15 14:54:00 0 0 0 2012-03-15 14:55:00 0 0 0 2012-03-15 14:56:00 0 0 0 2012-03-15 14:57:00 0 0 0 2012-03-15 14:58:00 0 0 0 2012-03-15 14:59:00 0 0 0 TICK-NYSE.Count 2012-03-15 14:54:00 31 2012-03-15 14:55:00 31 2012-03-15 14:56:00 31 2012-03-15 14:57:00 31 2012-03-15 14:58:00 29 2012-03-15 14:59:00 30 > str(TICK.NYSE) An ‘xts’ object from 2011-01-18 09:30:00 to 2012-03-15 14:59:00 containing: Data: num [1:114090, 1:8] -5 -144 24 -148 -184 -77 20 121 111 -60 ... - attr(*, "dimnames")=List of 2 ..$ : NULL ..$ : chr [1:8] "TICK-NYSE.Open" "TICK-NYSE.High" "TICK-NYSE.Low" "TICK-NYSE.Close" ... Indexed by objects of class: [POSIXct,POSIXt] TZ: xts Attributes: List of 4 $ from : chr "20110119 23:59:59" $ to : chr "20110124 23:59:59" $ src : chr "IB" $ updated: POSIXct[1:1], format: "2012-01-19 02:34:52" > str(index(TICK.NYSE)) Class 'POSIXct' atomic [1:114090] 1.3e+09 1.3e+09 1.3e+09 1.3e+09 1.3e+09 ... ..- attr(*, "tzone")= chr "" ..- attr(*, "tclass")= chr [1:2] "POSIXct" "POSIXt" > Sys.getenv("TZ") [1] "EST" > tail(index(TICK.NYSE)) [1] "2012-03-15 14:54:00 EST" "2012-03-15 14:55:00 EST" [3] "2012-03-15 14:56:00 EST" "2012-03-15 14:57:00 EST" [5] "2012-03-15 14:58:00 EST" "2012-03-15 14:59:00 EST" > head(index(TICK.NYSE)) [1] "2011-01-18 09:30:00 EST" "2011-01-18 09:31:00 EST" [3] "2011-01-18 09:32:00 EST" "2011-01-18 09:33:00 EST" [5] "2011-01-18 09:34:00 EST" "2011-01-18 09:35:00 EST" > Sys.info() sysname "Linux" release "3.0.0-16-generic" version "#28-Ubuntu SMP Fri Jan 27 17:44:39 UTC 2012" > sessionInfo() R version 2.14.1 (2011-12-22) Platform: x86_64-pc-linux-gnu (64-bit) locale: [1] LC_CTYPE=en_US.UTF-8 LC_NUMERIC=C [3] LC_TIME=en_US.UTF-8 LC_COLLATE=en_US.UTF-8 [5] LC_MONETARY=en_US.UTF-8 LC_MESSAGES=en_US.UTF-8 [7] LC_PAPER=en_US.UTF-8 LC_NAME=en_US.UTF-8 [9] LC_ADDRESS=en_US.UTF-8 LC_TELEPHONE=en_US.UTF-8 [11] LC_MEASUREMENT=en_US.UTF-8 LC_IDENTIFICATION=en_US.UTF-8 attached base packages: [1] stats graphics grDevices utils datasets methods base other attached packages: [1] lattice_0.20-0 multicore_0.1-7 [3] doSNOW_1.0.5 snow_0.3-8 [5] doRedis_1.0.4 rredis_1.6.3 [7] foreach_1.3.2 codetools_0.2-8 [9] iterators_1.0.5 PerformanceAnalytics_1.0.3.3 [11] quantstrat_0.6.1 blotter_0.8.4 [13] twsInstrument_1.3-3 FinancialInstrument_0.10.6 [15] IBrokers_0.9-6 quantmod_0.3-18 [17] TTR_0.21-0 xts_0.8-4 [19] Defaults_1.1-1 strucchange_1.4-6 [21] sandwich_2.2-8 zoo_1.7-7 [23] rj_1.0.2-5 loaded via a namespace (and not attached): [1] grid_2.14.1 tools_2.14.1 > dput(tail(TICK.NYSE)) structure(c(-385, -213, -42, -334, -233, -111, -121, 20, -14, -125, -73, 265, -583, -269, -426, -520, -443, -440, -213, -42, -334, -233, -111, 119, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 31, 31, 30, 30, 31, 31), class = c("xts", "zoo" ), .indexCLASS = c("POSIXct", "POSIXt"), .indexTZ = "", from = "20110119 23:59:59", to = "20110124 23:59:59", src = "IB", updated = structure(1326958492.96405, class = c("POSIXct", "POSIXt")), index = structure(c(1331927640, 1331927700, 1331927760, 1331927820, 1331927880, 1331927940), tzone = "", tclass = c("POSIXct", "POSIXt")), .Dim = c(6L, 8L), .Dimnames = list(NULL, c("TICK-NYSE.Open", "TICK-NYSE.High", "TICK-NYSE.Low", "TICK-NYSE.Close", "TICK-NYSE.Volume", "TICK-NYSE.WAP", "TICK-NYSE.hasGaps", "TICK-NYSE.Count")))

  Read the article

• Sending typedef struct containing void* by creating MPI drived datatype.

  - by hankol

  what I understand studying MPI specification is that an MPI send primitive refer to a memory location (or a send buffer) pointed by the data to be sent and take the data in that location which then passed as a message to the another Process. Though it is true that virtual address of a give process will be meaningless in another process memory address; It is ok to send data pointed by pointer such as void pointer as MPI will any way pass the data itself as a message For example the following works correctly: // Sender Side. int x = 100; void* snd; MPI_Send(snd,4,MPI_BYTE,1,0,MPI_COMM_WORLD); // Receiver Side. void* rcv; MPI_Recv(rcv, 4,MPI_BYTE,0,0,MPI_COMM_WORLD); but when I add void* snd in a struct and try to send the struct this will no succeed. I don't understand why the previous example work correctly but not the following. Here, I have defined a typedef struct and then create an MPI_DataType from it. With the same explanation of the above the following should also have succeed, unfortunately it is not working. here is the code: #include "mpi.h" #include<stdio.h> int main(int args, char *argv[]) { int rank, source =0, tag=1, dest=1; int bloackCount[2]; MPI_Init(&args, &argv); typedef struct { void* data; int tag; } data; data myData; MPI_Datatype structType, oldType[2]; MPI_Status stat; /* MPI_Aint type used to idetify byte displacement of each block (array)*/ MPI_Aint offsets[2], extent; MPI_Comm_rank(MPI_COMM_WORLD, &rank); offsets[0] = 0; oldType[0] = MPI_BYTE; bloackCount[0] = 1; MPI_Type_extent(MPI_INT, &extent); offsets[1] = 4 * extent; /*let say the MPI_BYTE will contain ineteger : size of int * extent */ oldType[1] = MPI_INT; bloackCount[1] = 1; MPI_Type_create_struct(2, bloackCount,offsets,oldType, &structType); MPI_Type_commit(&structType); if(rank == 0){ int x = 100; myData.data = &x; myData.tag = 99; MPI_Send(&myData,1,structType, dest, tag, MPI_COMM_WORLD); } if(rank == 1 ){ MPI_Recv(&myData, 1, structType, source, tag, MPI_COMM_WORLD, &stat); // with out this the following printf() will properly print the value 99 for // myData.tag int x = *(int *) myData.data; printf(" \n Process %d, Received : %d , %d \n\n", rank , myData.tag, x); } MPI_Type_free(&structType); MPI_Finalize(); } Error message running the code: [Looks like I am trying to access an invalid memory address space in the second process] [ubuntu:04123] *** Process received signal *** [ubuntu:04123] Signal: Segmentation fault (11) [ubuntu:04123] Signal code: Address not mapped (1) [ubuntu:04123] Failing at address: 0xbfe008bc [ubuntu:04123] [ 0] [0xb778240c] [ubuntu:04123] [ 1] GenericstructType(main+0x161) [0x8048935] [ubuntu:04123] [ 2] /lib/i386-linux-gnu/libc.so.6(__libc_start_main+0xf3) [0xb750f4d3] [ubuntu:04123] [ 3] GenericstructType() [0x8048741] [ubuntu:04123] *** End of error message *** Can some please explain to me why it is not working. any advice will also be appreciated thanks,

  Read the article

< Previous Page | 69 70 71 72 73 74 75 76  | Next Page >