Search Results

Search found 2181 results on 88 pages for 'wifi cordon'.

Page 80/88 | < Previous Page | 76 77 78 79 80 81 82 83 84 85 86 87  | Next Page >

• How can I make IPv6 on OpenVPN work using a tap device?

  - by Lekensteyn

  I've managed to setup OpenVPN for full IPv4 connectivity using tap0. Now I want to do the same for IPv6. Addresses and network setup (note that my real prefix is replaced by 2001:db8): 2001:db8::100:0:0/96 my assigned IPv6 range 2001:db8::100:abc:0/112 OpenVPN IPv6 range 2001:db8::100:abc:1 tap0 server side (set as gateway on client) 2001:db8::100:abc:2 tap0 client side 2001:db8::1:2:3:4 gateway for server Home laptop (tap0: 2001:db8::100:abc:2/112 gateway 2001:db8::100:abc:1/112) | | | (running Kubuntu 10.10; OpenVPN 2.1.0-3ubuntu1) | wifi | | router | | OpenVPN INTERNET | eth0 | /tap0 VPS (eth0:2001:db8::1:2:3:4/64 gateway 2001:db8::1) (tap0: 2001:db8::100:abc:1/112) (running Debian 6; OpenVPN 2.1.3-2) The server has both native IPv4 and IPv6 connectivity, the client has only IPv4. I can ping6 to and from my server over OpenVPN, but not to other machines (for example, ipv6.google.com). Using tcpdump on both the server and client, I can see that packets are actually transferred over tap0 to eth0. The router (2001:db8::1) send a neighbor solicitation for the client (2001:db8::100:abc:2) to eth0 after it receives the ICMP6 echo-request. The server does not respond to that solicitation, which causes the ICMP6 echo-request not be routed to the destination. How can I make this IPv6 connection work?

  Read the article

• IPv6 works only after ping to routing box

  - by Ficik

  Situation: There is ipv4 only router in network and every computer is connected to it (wifi or cable). Server with ipv4 and ipv6 is connected to this router as well. Server has configured tunnelbrokers 6to4 tunnel and radvd. Clients in network has right prefix and can ping each other. But they can't ping to internet until they ping Server (the one with tunnel). I found somewhere that it's icmp problem, but I couldn't find solution. Is it problem that there is ipv4 only router? server and client runs linux router runs dd-wrt without ipv6 support :( Ping try: standa@standa-laptop:~$ ping6 ipv6.google.com PING ipv6.google.com(2a00:1450:8007::69) 56 data bytes ^C --- ipv6.google.com ping statistics --- 29 packets transmitted, 0 received, 100% packet loss, time 28223ms standa@standa-laptop:~$ ping6 2001:470:XXXX:XXXX:21c:c0ff:fe2b:6478 PING 2001:470:XXXX:XXXX:21c:c0ff:fe2b:6478(2001:470:XXXX:XXXX:21c:c0ff:fe2b:6478) 56 data bytes 64 bytes from 2001:470:XXXX:XXXX:21c:c0ff:fe2b:6478: icmp_seq=1 ttl=64 time=3.55 ms 64 bytes from 2001:470:XXXX:XXXX:21c:c0ff:fe2b:6478: icmp_seq=2 ttl=64 time=0.311 ms 64 bytes from 2001:470:XXXX:XXXX:21c:c0ff:fe2b:6478: icmp_seq=3 ttl=64 time=0.269 ms 64 bytes from 2001:470:XXXX:XXXX:21c:c0ff:fe2b:6478: icmp_seq=4 ttl=64 time=0.292 ms ^C --- 2001:470:XXXX:XXXX:21c:c0ff:fe2b:6478 ping statistics --- 4 packets transmitted, 4 received, 0% packet loss, time 3000ms rtt min/avg/max/mdev = 0.269/1.107/3.559/1.415 ms standa@standa-laptop:~$ ping6 ipv6.google.com PING ipv6.google.com(2a00:1450:8007::69) 56 data bytes 64 bytes from 2a00:1450:8007::69: icmp_seq=1 ttl=57 time=20.7 ms 64 bytes from 2a00:1450:8007::69: icmp_seq=2 ttl=57 time=20.2 ms 64 bytes from 2a00:1450:8007::69: icmp_seq=3 ttl=57 time=23.4 ms ^C --- ipv6.google.com ping statistics --- 3 packets transmitted, 3 received, 0% packet loss, time 2001ms rtt min/avg/max/mdev = 20.267/21.479/23.413/1.392 ms

  Read the article

• How to connect computers to a network printer behind a router?

  - by kokbira

  General question: How to connect computers to an IP printer behind a router? Particular question: How to connect C-1 and C-2 to PRI? What? Where? [ISP] | | -> IPs:200.X.X.X/other configs:DC | [R-1] | | -> IPs:10.1.X.X locked by MAC,M:255.0.0.0,G:10.1.0.1 |¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯| | | [PRI] IP:10.1.7.7 [R-2] IP: 10.1.0.1,MAC:A | | -> IPs:192.168.1.X,M:255.255.255.0,G:192.168.1.1 |¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯| | | [C-1] IP:192.168.1.2 [C-2] IP:192.168.1.3,MAC:A Glossary and details: ------------------------------------------------------------------------------------ - IP: IP. - IPs: Some IP range. - M: Mask. - G: Gateway. - MAC:A: A MAC address that I will not inform you :) - DC: Don't care. - ISP: Internet Service Provider (not so much details about it on that case). - R-1: A real router or some concatenated so IP range bellow that block is 10.1.X.X and above is ISP. The provided IPs are provided by MAC. As all available addresses are in use, you must clone an existing one to join with a new device (and to disconnect the cloned one). - PRI: An network printer (some people here call that IP printer). - R-2: A TP-LINK TL-WR340G, mine wireless router (since my computer does not have ethernet input, it is my ethernet-wifi adapter :), admin access, MAC address cloned from C-2 (MAC:A). I've to configure 10.0.1.1 and 10.0.1.2 as DNS addresses, other wise I cannot connect C-1 and C-2 to Internet. - C-1: My computer, a CCE XLE-425 (remember: no ethernet input), with Windows 7, admin access. - C-2: another computer with better configs than mine, MAC:A, Windows XP. Requirements: I want to print, to access Internet and to do it myself (no need to call network admin men in black people). Pay attention to MAC clones and DNS info.

  Read the article

• SSH Connection Error : No route to host

  - by dewbot

  There are three machines in this scenario: Desktop A : [email protected] Laptop A : [email protected] Machine B : [email protected] All the machines have Ubuntu 11.04 (Desktop A is a 64bit one) and have both openssh-server and openssh-client. Now when I try to connect Desktop A to Laptop A or vice-versa by ssh [email protected] I get an error as port 22: No route to host in both the cases. I own both the machines, now if I try same commands from my friend's machine, i.e. via Desktop B, I can access both my Laptop and Desktop. But if I try to access Desktop B from my Laptop or by Desktop I get port 22: Connection timed out I even tried changing ssh port no. in ssh_config file but no success. Note: that 'Laptop A' uses WiFi connection while 'Machine A' uses Ethernet Connection and 'Machine B' is on an entirely different network. Laptop A && Desktop A - Router/Nano_Rcvr provided to me by ISP. So to one Router two Machines are connected and can be accessed at the same time. here is my ifconfig output for both the machines :- Laptop wlan0 Link encap:Ethernet HWaddr X:X:X:X:00:bc inet addr:1.23.73.111 Bcast:1.23.95.255 Mask:255.255.224.0 inet6 addr: fe80::219:e3ff:fe04:bc/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:108409 errors:0 dropped:0 overruns:0 frame:0 TX packets:82523 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:44974080 (44.9 MB) TX bytes:22973031 (22.9 MB) Desktop eth0 Link encap:Ethernet HWaddr X:X:X:X:c5:78 inet addr:1.23.68.209 Bcast:1.23.95.255 Mask:255.255.224.0 inet6 addr: fe80::227:eff:fe04:c578/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:10380 errors:0 dropped:0 overruns:0 frame:0 TX packets:4509 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1790366 (1.7 MB) TX bytes:852877 (852.8 KB) Interrupt:43 Base address:0x2000

  Read the article

• Internet setup for my office

  - by prakash

  We have two internet connections to our office and our current setup is like this.. The internet connections require pppoe log in so i take each cable and plug it into a wifi router and configure the router to log in to the pppoe and then plug in a cable from the router to a switch and distribute the internet throughout my office. The problem with this setup is it is really hard to monitor and im not able to monitor who is hogging internet usage and what he or she is actually using it for. apart from this we also have a nas setup which is routed through another switch . Could someone please throw a little light on how i can restructure this setup for easy monitoring and better transparency... ? each wan router is connected to a different switch and is distributed to users accordingly.. we have around 40 users in the office.. we want to setup a single linux box to which i want to connect the two wan connections and from there distribute it to all our users.... im looking for a solution where we do not have to invest more that buying a single pc and a couple of nics

  Read the article

• Curious enigma of a network cable / connection / quality

  - by Foo Bar

  So, the situation is like this: I'm renting an apartment in a large house and I'm sharing internet with the landlord who lives downstairs. The internet is (in my best guess) optical 20/20Mbit. I don't know how it's all wired in his flat (haven't been there / seen it). Anyway, in my flat comes a cable which seems to be connected directly to the optic to ethernet router (and the password is the default one, so I have access, he he). There was a switch connected to that and to wires that go around the flat, and the wiring is terrible. It's even mixing phone and ethernet, and from what I see some cables are even interconnected!? Anyways, this cable that comes to my flat is very short. I can barely connect my computer on it, but if I do, I seem to get decent speed / performance. Not great, but decent. If, however, I connect switch to it (tried 2 different switches and a wifi switch) it's all blinking but I can't even connect to 192.168.1.1 (the router). DHCP fails, ping is losing 80-100% of replies. So I connected this cable directly to the other cable which goes to my work room, with a connector that has two female jacks and no electronics. Now when I connect my computer in my room, again, the performance is decent. When I connect WRT54GL (with tomato, DHCP disabled) to it and I plug a cable in this WRT and to my computer... the performance is gone. Download seems okay on Speedtest, but upload is .2Mbps and it's connecting forever. So what kind cable troll am I having here? Any ideas?

  Read the article

• Win7 Hangs During App Install/Upgrade/Uninstall

  - by JadeMason

  I have a custom built PC that intermittently hangs when installing, uninstalling, or upgrading applications. Technical Specs ASUS P5E w/ WiFi Motherboard Intel Core2 Quad Q6600 Processor 4x 2GB G.Skill DDR2 800 SDRAM ASUS EAH2900XT / Radeon HD 2900XT 512MB Video Card Under normal operation the machine runs reliably, even under heavy load, such as video transcoding. The temperature never gets anywhere near where I would worry about it. However, the machine regularly hangs (complete lockup, no response to keyboard or mouse, no activity on-screen) when either installing a new application, uninstalling an existing application, or applying patches to existing applications or the OS. This is extremely frustrating as this machine is primarily used as a HTPC. Several apps are configured for automatic updates, and these updates sometimes cause the machine to lockup while we are watching content on the PC. In previously investigating this issue, I found one likely problem could be my Logitech Webcam. The Logitech software has a bug that leaves an entry in HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\ Control\SessionManager\PendingFileRenameOperations Which references the Temp directory. My registry contained this error, so I uninstalled the webcam software and deleted this registry key value. Unfortunately, the machine will still intermittently hang. I've noticed that the hangs always happen when an install/upgrade/uninstall requires elevated privileges (presumably to modify the registry). I can typically get at least one install/upgrade/uninstall to complete after a reboot, but after that it is a game of russian roulette to see if the operation will succeed or hang the machine. The event log is not helpful, as log messages end at the time of the hang, with no record of a warning or error. My only recourse when the machine hangs in this way is to perform a hard reset/power cycle. Any tips on how to further debug this issue are greatly appreciated.

  Read the article

• Without an internet connection my computer loads programs slowly. With an internet connection they load quickly

  - by Peter pete

  Gday. I've a laptop, with 8gb of RAM and a Samsung 830 SSD with about 2/5th of free space out of its 256gb. Win7 64b. Laptop is a Toshiba T130. In the other day I noticed that it took a long time to load a program, for example the python interpreter at the time the computer didn't have access to the home network. In both cases the computer boots quickly. About 40 seconds. Without internet opening the python interpreter, or notepad2.exe, or any program individually takes around 10 seconds. With internet connection (through WiFi) opening the same programs takes about 2 seconds. In both cases, it becomes SSD-instant-quick to open a program from a cold boot. I don't have any network mapped drives. I've tried with AV off (Avast antivirus) and same effect. I've installed all MS updates. I've googled and googled and have found nothing of help. I've run the Samsung SSD magician to "optimise" ssd and that didn't help. What could I do to determine & fix this issue?

  Read the article

• SBS 2008 - DNS Forwarders timing out.

  - by Moif Murphy

  Hello, We have an SBS 2008 server that keeps losing connection to the internet approx 2-3 times a day. It's a simple setup, BT Business Broadband ADSL to a Wireless Zyxel router to the server. Clients connect via WiFi from their laptops. Plugging ethernet in makes no difference, only a reboot of the router seems to bring everything back again. I'm looking at the forwarders on the DNS properties page and they're timing out when trying to resolve the IPs. Currently there are two IPs in there, 194.72.9.34 which has timed out and 194.72.9.38 which has finally resolved to ns8.bt.net We've been in there and replaced all media, installed a PCI NIC, have changed the router three times. There are no errors in the DNS event logs pertaining to what's going on. We've also been on to BT who are adamant that it's not their end. Could someone shed some light on what could be going on or where else to look in the configuration of the server? Thank you.

  Read the article

• Wireless driver activation issue in Compaq c700 in Ubuntu 9.04

  - by Fazil

  I am using Ubuntu 9.04, I cant access my wireless driver, I activate the madwifi in administrationhardware drivers, but I could'nt activated the wireless too. when I type lspci I get the following message, ################################################## # 00:00.0 Host bridge: Intel Corporation Mobile PM965/GM965/GL960 Memory Controller Hub (rev 03) 00:02.0 VGA compatible controller: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (rev 03) 00:02.1 Display controller: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (rev 03) 00:1b.0 Audio device: Intel Corporation 82801H (ICH8 Family) HD Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 1 (rev 04) 00:1d.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #1 (rev 04) 00:1d.1 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #2 (rev 04) 00:1d.2 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #3 (rev 04) 00:1d.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #1 (rev 04) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev f4) 00:1f.0 ISA bridge: Intel Corporation 82801HEM (ICH8M) LPC Interface Controller (rev 04) 00:1f.1 IDE interface: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E) IDE Controller (rev 04) 00:1f.2 SATA controller: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E) SATA AHCI Controller (rev 04) 00:1f.3 SMBus: Intel Corporation 82801H (ICH8 Family) SMBus Controller (rev 04) 01:00.0 Ethernet controller: Atheros Communications Inc. AR242x 802.11abg Wireless PCI Express Adapter (rev 01) 02:01.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) ################################################## but when I tried in Windows I found that the driver for my laptop is ################################################ atheros AR5007 802.11b/g WiFi Adapter ################################################ so what can I do for solving this problem.

  Read the article

• Could 0x800CCC0E in Outlook be caused by bad wireless connection?

  - by AndrejaKo

  I have a computer connected to a WiFi access point/router/modem. Sometimes, I get page not found errors and similar when opening a browser window, sometimes pings fail and it looks like the router's signal isn't very good. On the other hand, I get around 4 bars of signal strength in windows and graph looks good in Inssider. I also never get dropped connection to the router. My main problem is that I often get errors (such as 0x800CCC0E) in Outlook 2010 that after some searching appear to be connected to bad server connection. I'm using GMail over IMAP and all settings are correct. I didn't have similar errors on my previous router, but I'm not 100% sure that they appeared after switching to current one. It may have worked for some time without errors. There are also around 3000 messages on the server and the size of mailbox is around 12 GiB, which may contribute to the problems. On the other hand, there are at least 24 other networks in the 2.4 GHz range which I'm using and the number may have increased since I switched routers. Should I try solving this by getting a router with stronger signal?

  Read the article

• How to improve Samba performance on VirtualBox machine?

  - by ColinM

  I am running a Windows 7 64bit host and Ubuntu 9.04 32bit guest inside of VirtualBox 4.0.0 on a laptop which has internet connectivity via Wifi. The main use is writing code for which I use Netbeans. My dev environment is hte virtual machine and I use Samba on the VM to share the code directory so that I can use Netbeans on the host as my IDE. Unfortunately Netbeans does a lot of disk access and due to the poor Samba performance it makes the IDE hardly usable. How can I improve performance of the Samba share? On my desktop it isn't so bad but I don't know what the difference would be since they are similar setups (Win 7 hosts, cloned guests, SSDs, Vbox guests using SATA in AHCI mode, etc..). With Bridged networking is the performance between the host and guest limited by the physical hardware (Intel 6200 AGN on laptop)? I switched to Host-only and it didn't seem to improve performance at all. To clarify bad performance, I used 7zip to zip a project directory and got 19kbs to 500kbs depending on the size of the files being zipped. On my desktop it was in the ~10mbs range. Any tips for VirtualBox/Samba configuration to get improve the performance? I am using Samba 3.3.2. Hopefully Samba with SMB2 support will be released soon..

  Read the article

• Ubuntu Server Wireless connection issue - replaced router but kept ESSID

  - by Stevo

  I have a ubuntu server 12.04 which was connected to my wireless network with no problem I replaced the wireless router but kept the ESSID and password the same. All other devices on network have connected correctly. However the Ubuntu Server will not route correctly. It will connect to the wifi router, and get a dhcp served IP address, however it will not route anything. I cannot ping the router from the server. the contents of /etc/resolve.conf are updated with the information from the router, (the host name has been served) I know there is nothing wrong with the router or the server, or the wireless card etc. I'm assuming there's some cached setting that associates the old router with the ESSID and causing the issue. I've got a lot of other devices connected to the router, so don't want to change the name of the ESSID. How do I fix this? EDIT: outputs (abbreviated as I've got no cut and paste) netstat -rn: Kernel IP Routing table Dest Gate Gen Flags MSS Window irtt Iface 0.0.0.0 192.168.0.1 0.0.0.0. UG 0 0 0 wlan0 192.168.0.0 0.0.0.0. 255.255.255.0 U 0 0 0 wlan0

  Read the article

• I can't connect to internet via lan cable because 2032 battery died and my bios bios info is now empty [closed]

  - by Rand Om Guy

  I have a compaq CQ61-112SL from about 5 years now... the main battery is almost dead, doesn't keep more then 10 minutes. anyway my problem is that my motherboard battery didn't have any more energy left a few days ago and since then I can't access internet through lan cable but only via wifi. I need cable though. I saw that on my BIOS setup page there were a bunch of parameters missing like serial number, UUID, product number and stuff like that. Also when I start the notebook it prints something like : No serial found. or something like that. I don't really know if the reason why my lan cable doesn't work is the empty BIOS but i assume that's it. If it's not please enlighten me. Or anyway tell me how to update the serial number and product number to the real ones (instead of the 0000000000000 that is now in my bios). I downloaded HP DMI which should make it possible to set these variables on the BIOS but i'm on Windows 8 64bit and the executable file that I need to open for my laptop model says it can't run on 64 bit.

  Read the article

• 412 Precodition Failed error only occurs on certain networks

  - by Andy

  One of my favorite websites: http://jessiejofficial.com (yes, I'm a Jessie J Fan :')) has recently started displaying the error message "412 Precondition Failed" whenever I visit it from my home network, even when I use Tor Browser. At first I thought that this was an issue with the whole website, however I have contacted the web developer and he has said that they has been plenty of hits within the last 48 hours. Plus, I discovered tonight that I can access the website from my phone, through the mobile network. So it appears to just be my network as all of the devices in my house connected to the WiFi display the same error when I try to visit any page of the site. However there have been no changes that we are aware of or are noticeable to our network since the website was accessible, and I have just heard that another person in a different part of the country is experiencing the same difficulties also. Any help/advice/suggestions would be appreciated greatly Update: When trying to ping 'jessiejofficial.com' in Windows command prompt the request times out on all four attempts, on any computer connected to the wireless network. I can now also confirm that the same thing occurs on my MacBook Pro.

  Read the article

• Dropbox picture sync: Skip RAW files?

  - by Steven Lu

  I like the convenience of having Dropbox keep track of my photos because it tends to work with my devices over 3G (I am often tethering to my phone with my iPad and Macbook) as well as Wifi, but it's a waste of network traffic to sync the raw files from my camera or memory card. It clutters up the dropbox list and the files are just huge. Is there a way to configure the Dropbox client so that it ignores a certain file extension for the picture sync? Also, I suspect that if I just go and delete the raw files, that the next time I plug in the memory card and tell Dropbox to sync, it will re-download the raw files. Which would be terribad. I could switch to iCloud for Photo Stream, I suppose, but there will be no access via 3G that way. And I've already got years of experience with Dropbox so I know it's going to just work. I think any method that works for filtering files to exclude from sync on Dropbox in general should work here too. Edit: Wow there are 19k votes for this exact request.

  Read the article

• Embedded Windows XP

  - by Kyle

  My company acquired a brake press for bending large structural steel plates. We received it second hand and it came with an embedded copy of windows XP. Now for the part that's driving me nuts: plug and play has been turned off, also accessibility options has been disabled. What does this mean for me? Keyboards will not work! Nothing that plugs into a USB port will work and it does not have a CD ROM drive. I have tried to turn on plug and play using the on screen keyboard but it is not there since accessibility options is turned off. I would just get an updated copy of the the embedded OS but they come from Sweden and are extremely expensive. I assume there has got to be a way to get a USB devices to work. We need to get a wifi adapter on it so I can use team viewer and remotely configure it for our needs. Things to keep in mind: There is no keyboard so everything has to be done with the mouse There is no PS2 port for a keyboard just a mouse. Odd. I am 5 states away from this location and have been working with a tech who is physically installing the machine. System 32 seems to be missing A LOT of files, the tech told me there is only 8 folders in there and no other files (I don't even understand how Windows is running like this). If anyone has ANY ideas I would appreciate it, I am unsure where to go from here.

  Read the article

• cheap gigabit switch for small business

  - by neoice

  my friend's business is currently borrowing my Adtran 1224R and is very happy with it. it's configured with a few VLANs to segment customers, internal traffic and public wifi. port 1 is a "trunk" port to the router, a chunky Linux box with iptables+NAT. they push a lot of traffic over the LAN (data backups) and really need gigabit. besides, I'd like my Adtran back :P my goal is to find a cheap(ish) switch that can function as a drop-in replacement. it looks like VLAN trunking is actually part of the 802.1q spec, so anything with VLAN support should cover the current trunk-to-router setup. it's nice to have both a web interface and SSH, but I can configure it either way if needed. things like the Netgear GS724T have caught my eye, but it seems like none of the hardware in the $300-500 range have really solid reviews. I'm concerned that "cheaper" hardware might not work for a network full of power users. does anyone have a recommendation for the Netgear GS724T or a switch that will meet my needs?

  Read the article

• Viewing local websites on my iOS device over Wi-fi

  - by John

  Trying to view some local html/css/js files in a mobile browser on my iOS device. Thought maybe file-sharing would be an option, and is, but I'm not completely satisfied with it. Any time I try to do the following an error occurs. Web sharing is on and available at http://192.168.1.101/~user but I have to manually copy the files in. If I try to symlink a folder in so that the address could be viewed at ''~user/some_dir by issuing $ ln -s /Users/user/dev/some_dir ~/Sites/ then I get a 403 forbidden error. I've tried to remedy this by modifying a user.conf file in /private/etc/apache2/ and using the following syntax: <Directory "/Users/user/Sites/"> Options Indexes MultiViews SymLinks AllowOverride None Order allow,deny Allow from all </Directory> but nope, still doesn't work. I get a 403 error. If I try to symlink each individual file in instead of using a directory as a sub-directory, same error. Any help would be greatly appreciated! I'd just like to symlink directories into the ~/Sites one and browse them on my iOS device over wifi. I'm on OS X 10.7 Lion trying to connect with iOS 5.

  Read the article

• FTP Server upload and filesystem questions

  - by Alex

  I'm a photographer who mainly does event photography. A while ago I bought myself a Nikon WT-4 wireless transmitter, a small device which connects via USB to my Nikon D700 DSLR, and then establishes a WiFi connection to an existing WLAN. It can then upload any pictures I take via FTP to an FTP server somewhere in the network. On my laptop I then have a piece of software which will check a given folder on the disk regularly, this software is smart enough to look at the modified file timestamp, if this timestamp is less than 10 seconds ago, it will not attempt to import the folder and skip the file in this iteration of the import scan. The problem I've discovered seems to be inherent to the FTP protocol, as I have the same problem with Windows 7 built in IIS server, as I do with FileZilla FTP server. When the transmitter starts to upload a file, the FTP server will create a small 300-500 KB file with the correct filename on the disk, but then do nothing with the file until it has completely received the file via FTP. So it seems to create this small dummy file, and then buffer the remainder of the FTP upload until it's finished, and then dump the rest of the file into the dummy file making it the correct size. Problem is, these uploads take about 15-30 seconds depending on reception, but since the folder watch tool will already try to import any file older than 10 seconds, it will always try to import the small dummy files which obviously fails as they're not copmlete yet. Is there any way to 'disable' this behaviour? Ideally I would like my file only to show up once it's been completely uploaded. Or perhaps someone knows another FTP server application (it has to run on win7) which does not show this behaviour?

  Read the article

• Is it possible to command a common router without using the web interface?

  - by MDeSchaepmeester

  Some background The internet arrangement in my student home is really weird. There is one ethernet outlet and several wifi hotspots. Either way requires a login through a web site to get internet access. This is annoying as each device needs to login seperately and with a PS3 for example, it is impossible to get connected at all since the web login procedure doesn't work. Therefore I have installed a D-Link DIR-635 router which is connected to the ethernet outlet. It has DHCP enabled so it uses NAT, but whatever it is connected to also uses NAT and I've read this should not work. A fellow student tried it with an Apple Airport but that keeps giving errors related to NAT after NAT. Anyway my setup does work so bonus points if you can clarify this. I need to login to the web site I mentioned earlier with any device, after which all devices in my LAN have connectivity. This is great. Except... In short From time to time, I lose internet connectivity and my D-Link DIR-635 router needs to do a DHCP renew. I can do this via the web interface but my life would be easier if I could just run a cmd file which tells my router to do this without all the hassle. This would setup a connection to my router and execute the proper command. I have tried googling but couldn't find much helpful stuff.

  Read the article

• XBMC remote control key repeat

  - by Amigable Clark Kant

  Those who have used XBMC with a WiFi remote, such as an Android or iOS device with the official XBMC remotes, have probably seen this at one time or another: your remote stops working, when you press a key, that key is repeated very fast. Sometimes you can break the key repeat loop by pressing that same key again. Sometimes (as this particular morning) you can not. This problem has existed for literally years (it even occurs on the old XBOX only builds) but there seems to be no definite explanation as to what is causing it. I am asking for a workaround. (If you Google, you can find threads were people are ridiculed for bringing up this problem, which is one reason I ask here instead of on the official forums. Also the fact that this problem has persisted for so many years.) I am running, right now, XBMCBuntu Live Eden and the latest official iOS remote. Although, I have seen this problem on all combinations of remotes and XBMC versions I have tried over the years, which are many. (XBMC on Windows, Linux, OSX, remotes on Android and iOS.) Link to bug #136 for the Android remote. It's marked as "fixed" as of client version 636, but the problem is seen again in rev 730. Go figure. There is something fundamentally wrong with how keypresses are sent from the various remotes to XBMC, since this problem is seen across time, XBMC versions and iOS/Android.

  Read the article

• Can't Ping - Wireless network of home

  - by Naunidh

  Hello, This may seem like other ping problem, but I have tried a lot before posting it here. I have a linksys WRT54G - firmware v8.00.8. I have two laptops one windows vista (192.168.1.99) and Windows Xp (192.168.1.13) connected on WiFi . The Router's IP address is 192.168.1.4, and default gateway is the ADSL modem (192.168.1.1) connected through wire. The problem is that laptops can not ping each other, they can ping the gateway and the linksys router, and both can access internet. Following has been tried (I am pinging from XP machine to Vista): I saw that arp entires for Vista machines were not being populated, so I added static ARP entries. 192.168.1.99 00-19-7e-70-d0-4e static I checked on ethereal that an ICMP packet for MAC address of Vista machine does go out from XP machine towards the Vista machine, but never reaches the Vista machine. So its get eaten by the Router? I added Vista machine to DMZ in my linksys router, so that all the ports are open (In case it was an issue). Firewalls , antivirus etc were turned off, echo was enabled explicitly on vista, file sharing, network discovery were turned on. Network type was set to private. Unchecked everything in Router;s firewall, even though they are only meant for WAN requests. Is there anything else that I should try. Thanks.

  Read the article

• How can I determine the IP addresses allocated by DHCP on a router that I'm connected to?

  - by user234831

  This "router" is not a typical situation. I'm using my phone as a hotspot and can only configure a select number of DHCP options. I can manage the limit on how many devices/clients can use my phone as a hotspot. I have to select from a radio-button list with the options: 2,3,4,5, or 8 I can specify the DHCP starting IP address. In this case, it begins at 192.168.6.106 When I'm connected via WIFI to my phone, an ipconfig /all command shows me that the default gateway is 192.168.6.1 and my IPv4 address is 192.168.1.148. I have the luxury of connecting another device to the phone and that device was assigned 192.168.1.121. I've tried connecting to 192.168.6.1, hoping for some sort of router setup page that I'm used to seeing, but there is no such thing or maybe it's just a matter of incompatable operating systems. In summary, the "router" (phone) has an IP address of 192.168.6.1 and a DHCP server that begins at 192.168.6.106 and allows up to 8 connections. Normally, I would assume a range of 192.168.6.106 - 192.168.6.113, but connected clients are showing otherwise. How can I figure out which IP addresses are set aside by DHCP for clients?

  Read the article

• Locate devices within a building

  - by ams0

  The situation: Our company is spread between two floors in a building. Every employee has a laptop (macbook Air or MacbookPro) and an iPhone. We have static DHCP mappings and DNS resolution so every mobile gets a name like employeeiphone.example.com, every macbook air gets a employeelaptop.example.com and every macbook pro gets a employeelaptop.example.com on the Ethernet interface (the wifi gets a dynamic IP from a small range dedicated for the purpose). We know each and every MAC address of phones and laptops, since we do DHCP static mapping (ISC DHCP server runs on linux). At each floor we have a Netgear stack of two switches, connected via 10GB fiber to each other. No VLANs so far. At every floor there are 4 Airport Extreme making a single SSID network with WPA2 authentication. The request: Our CTO wants to know who is present at which floor. My solution (so far): Every switch contains an table listing MAC address and originating port. On each switch stack, all the MAC addresses coming from the other floor are listed as coming on port 48 (the fiber link). So I came up with: 1) Get the table from each switch via SNMP 2) Filter out the ones associated with port 48 3) Grep dhcpd.conf, removing all entries not *laptop and not *iphone 4) Match the two lists for each switch, output in JSON or XML 5) present the results on a dashboard for all to see I wrote it in bash with a lot of awk and sed, it kinda works but I always have for some reason stale entries in the switch lookup tables, making it unreliable; some people may have put their laptop to sleep, their iphones drop connections after a while, if not woken up and so on..I searched left and right, we are prepared to spend a little on the project too (RFIDs?), does anybody do something similar? I can provide with the script if needed (although it's really specific to our switches and naming scheme). Thanks! p.s. perhaps is this a question for stackoverflow? please move if it so.

  Read the article

< Previous Page | 76 77 78 79 80 81 82 83 84 85 86 87  | Next Page >