Search Results

Search found 30514 results on 1221 pages for '10 04'.

Page 84/1221 | < Previous Page | 80 81 82 83 84 85 86 87 88 89 90 91  | Next Page >

• 3 Headed Display Ubuntu Wallpaper

  - by Kyle Brandt

  I got 3 display working in Linux. I have set it up so I have Xinerama and 3 different X sessions. So my 3 displays are not all the same size, two are 1680x1050 and then the other which is between the two is 2560x1600. So my issue is when I chose span, even if the image is larger than all 3 resolutions combined, the center monitor has bars at the top and the bottom because span scales the image it seems. Is there a way if I bypass the gui to have an image span all three monitors but with no scaling? Urgent! Please help! ;-)

  Read the article

• pdns-recursor allocates resources to non-existing queries

  - by azzid

  I've got a lab-server running pdns-recursor. I set it up to experiment with rate limiting, so it has been resolving requests openly from the whole internet for weeks. My idea was that sooner or later it would get abused, giving me a real user case to experiment with. To keep track of the usage I set up nagios to monitor the number of concurrent-queries to the server. Today I got notice from nagios that my specified limit had been reached. I logged in to start trimming away the malicious questions I was expecting, however, when I started looking at it I couldn't see the expected traffic. What I found is that even though I have over 20 concurrent-queries registered by the server I see no requests in the logs. The following command describes the situation well: $ sudo rec_control get concurrent-queries; sudo rec_control top-remotes 22 Over last 0 queries: How can there be 22 concurrent-queries when the server has 0 queries registered? EDIT: Figured it out! To get top-remotes working I needed to set ################################# # remotes-ringbuffer-entries maximum number of packets to store statistics for # remotes-ringbuffer-entries=100000 It defaults to 0 storing no information to base top-remotes statistics on.

  Read the article

• Ubuntu Server Wireless connection issue - replaced router but kept ESSID

  - by Stevo

  I have a ubuntu server 12.04 which was connected to my wireless network with no problem I replaced the wireless router but kept the ESSID and password the same. All other devices on network have connected correctly. However the Ubuntu Server will not route correctly. It will connect to the wifi router, and get a dhcp served IP address, however it will not route anything. I cannot ping the router from the server. the contents of /etc/resolve.conf are updated with the information from the router, (the host name has been served) I know there is nothing wrong with the router or the server, or the wireless card etc. I'm assuming there's some cached setting that associates the old router with the ESSID and causing the issue. I've got a lot of other devices connected to the router, so don't want to change the name of the ESSID. How do I fix this? EDIT: outputs (abbreviated as I've got no cut and paste) netstat -rn: Kernel IP Routing table Dest Gate Gen Flags MSS Window irtt Iface 0.0.0.0 192.168.0.1 0.0.0.0. UG 0 0 0 wlan0 192.168.0.0 0.0.0.0. 255.255.255.0 U 0 0 0 wlan0

  Read the article

• Is it possible to extend a 504 timeout in nginx on a per location basis

  - by codecowboy

  Is it possible to set timeout directives within a location block to prevent nginx returning a 504 from a long running PHP script (PHP-FPM? location /myurlsegment/ { client_body_timeout 1000000; send_timeout 1000000; fastcgi_read_timeout 1000000; } This has no effect when making a request to example.com/myurlsegment. The timeout occurs after approximately 60 seconds. PHP is configured to allow the script to run until completion (set_time_limit(0)) I don't want to set a global timeout for all scripts.

  Read the article

• When HDD becomes full, how to create a symbolic link to the data store on another disk?

  - by Brij Raj Singh

  I have a Linux Ubuntu machine which has an X GB hard disk. There is folder, say, /opt/software/data. The disk /dev/sda1 is almost full and I have attached another disk at /dev/sda2 which is mounted at /hdd2. Is it possible for me to link the folders /opt/software/data with /hdd2/software/data so, that every file get stored in the /hdd2/software/data but may be referred from the /opt/software/data? I can't do a reinstall of the software that creates this data, to change the default location of storage.

  Read the article

• Ubuntu 12.04 - Custom Quick Launcher Menu

  - by gotqn

  I have been using Ubuntu for few weeks now and I am have been trying to create custom menu which to add in the launcher. Please, note that my version is 12.04 and I have not got any experience with Linux. I have checked a lot articles and questions likes this one, but have not been able to find what I am looking for. I want to create a custom quick launcher menu and to add it the the standard launcher, but I want to add links to other programs or folders in it. For example: A browsers menu - when it is open (with right mouse click on it), my browsers will be listed: chrome safari opera firefox I even may add their icons there. Music menu - some shortcuts to my favorite music folders.

  Read the article

• Is it possible to forbid removal of files but allow creation of them for specific directory in Linux

  - by vava

  I have an application that creates temp files and quickly deletes them. But I'd like to keep those files, is there a way to do that in Linux?

  Read the article

• Cannot access/unlock top panel in Ubuntu 10.04 (Netbook Edition)

  - by Richard

  I recently upgraded to Ubuntu 10.04 (Netbook Edition) on my NC10 netbook and now I can't seem to access/unlock the top panel and add/delete programs. Right click doesn't bring up the options to let me change things. Can anyone help? Thanks in advance.

  Read the article

• Problems bringing up a second virtual network interface

  - by tubaguy50035

  I'm having issues adding a second IP address to one interface. Below is my /etc/networking/interfaces # The loopback network interface auto lo iface lo inet loopback #eth0 is our main IP address auto eth0 iface eth0 inet static address 198.58.103.* netmask 255.255.255.0 gateway 198.58.103.1 #eth0:0 is our private address auto eth0:0 iface eth0:0 inet static address 192.168.129.134 netmask 255.255.128.0 #eth0:1 is for www.site.com auto eth0:1 iface eth0:1 inet static address 198.58.104.* netmask 255.255.255.0 gateway 198.58.104.1 When I run /etc/init.d/networking restart, I get a fail error about bringing up eth0:1: RTNETLINK answers: File exists Failed to bring up eth0:1. Any reason this would be? I didn't have any problems with I first set up eth0 and eth0:0.

  Read the article

• 10 Million records = wiped MySQL DB?

  - by Josh K

  So I was trying to load some test data and it appears to have killed my entire database. This is one case where it's great to have backups! They were all plain insert queries, probably about a 900 MB file. What could have gone wrong?

  Read the article

• Can't get samba to see other PCs in Kubuntu 10.04 (Lucid)

  - by MaurizioPz

  I'm new to networking. I'm trying to share a folder between to computers (both have kubuntu 10.04 installed). I'm able to share a folder with samba and can see that folder through samba on the same computer. But if I try to go on the other PC I can't see the first one. Both PCs are on the "workgroup" workgroup. I've tried disabling the firewall with firestarter can somebody help me? thanks update: here's my samba.conf http://pastebin.com/SpuES468

  Read the article

• Underscore being appended to mounted disk name after Ubuntu upgrade.

  - by Dan

  I have Upgraded Ubuntu from version 9.10 to 10.04. Now when I mount any of my extra hard disks the drive name gets an underscore appended to it, as shown below. Which obviously messes up all my pahts. How do I prevent\correct this? /media/<drivename>_

  Read the article

• How can i use mono2.6 in monoDevelop 2.2 on ubuntu9.10

  - by fishbone

  I installed mono2.6 in parralel. but how can i use it in monodevelop2.2

  Read the article

• How to install (old) packages for Ubuntu 9.04?

  - by wchrisjohnson

  Based on some excellent feedback by Mark here (http://serverfault.com/questions/285598/should-i-clone-a-physical-server-to-create-a-vm-for-a-staging-server), today I was able to use the vmware converter to clone my production server for a staging server. However the nic won't come up no matter what I do. I attempted to inistall vmware tools, as I suspect that the fact that it is not installed might prevent the nic from working. (I have the nic set as a vmxnet3 card in the vm settings). The install failed because there were several dependencies missing as well as the Linux headers. Given that Ubuntu 9.04 has been EOL'd, the packages I need to install to get the vmware tools to install are no longer available. I doubt the ubuntu 9.04 install CD has the packages on it. What are my options? I'd rather not upgrade the version of Ubuntu yet, as the point of the vm right now is to maintain parity with the production server. Might I have better luck resetting the driver to use vmxnet2 instead of the vmxnet3? Thanks in advance! Chris

  Read the article

• Free Hosting control panel

  - by John Maxim

  Hello All, I'm in the mid of researching for one of the best hosting control panels. The server I run is Ubuntu and I have some experience with ISPConfig 2 & 3. Since I haven't explored any others available, what are the recommended ones for an Ubuntu server? I asked because I find that there seems to be some disabling and modifications required for an Ubuntu server if I need to use ispconfig which causes the server to change its actual way of running. It's quite good though, but any more recommended ones ? Something more organic? which doesn't require much breaking and changing. I'm not asking for the simple one, I don't mind going extra mile to install a powerful one but just try sticking with most Ubuntu's conventions will be an ideal one for me. And of course, if there happens to be something that meets the requirement as mentioned "Ubuntu conventions" and also simple to install at the same time, that'd be a bonus. Thanks in advance.

  Read the article

• Lost current user (shutdown/logoff) widget after upgrading to Ubuntu 10.04

  - by xyzman

  I've upgraded to 10.04 from 9.10. Everything went fine until I've rebooted. After reboot, I've received some message about status panel and being sleepy, dismissed it. However, I haven't seen the user widget on Gnome Panel since that. This image shows which widget I'm talking about. If some one has any ideas about how it's called properly, please share. http://img237.imageshack.us/img237/8274/sampleyu.jpg Anyway, the question is, how do I turn this panel (and ability to shut my system down without resorting to console) back?

  Read the article

• Sound plays on headphones and speakers with Lenovo ThinkPad L512 + Ubuntu 10

  - by Oscar Godson

  The only thing really missing from this install is this issue with the sound. I've searched all over the forums and i found one thing where you get the model and codecs and write them to a file, however, I can't seem to find what my "model" is because none of the postings have anything about Lenovo laptops. Here is the command they all asked for: Code: cat /proc/asound/card0/codec#* | grep Codec Codec: Realtek ALC269 Codec: Intel G45 DEVIBX With that info, how do I get the model, and how do I get my speakers to stop playing when headphones are plugged in. Also, I don't have any software installed like pulse audio either, so it's not that. Thanks so much to whoever can answer this... The Ubuntu forums are nearly useless... ive never gotten a correct answer back on that site.

  Read the article

• Reasons for Wi-Fi to be slower on Ubuntu compared to Windows?

  - by den-javamaniac

  I'm using 64-bit Ubuntu 12.04 and Windows 7 64 bit – dual boot on the same computer. Connecting to the same wireless network. And it turns out that on Windows I get a more stable and stronger signal than on Ubuntu. To my knowledge there's a router which serves as a gateway and then there's a cable connected to the router which goes further to ISP, so the results for both OS should be the same. I've tested the issue on both OSs at various times and it gave me the same result. The question is why? Why Ubuntu networking is worse than that of Windows?

  Read the article

• Sending a large number of mails causing problems on CentOS 6 / Plesk 10

  - by papakost

  I have a VPS running CentOS 6. When the system tries to send daily newsletter, after some time (e.g. after sending about 2000 emails), I get error "Unable to send mail" and the system memory goes really high. Till this moment, the mails are delivered normally. The rest symptoms are: I cannot see anything on /var/log/maillog (File seems not to be written) All files on /var/spool/mail have 0 bytes size. From time to time on httpd log I get errors like: /usr/sbin/sendmail: error while loading shared libraries: libc.so.6: cannot open shared object file: Error 23 "Activate mail service on domain" setting in Plesk is deactivated. Any idea on what's going wrong here?

  Read the article

• Problem with Ubuntu 10.04 and ATI

  - by Maximilinao

  I'm having a problem installing the drivers from the video card. Just finished installing the driver, reboot my OS, and my monitor is starting off in energy saving mode and does not boot Ubuntu. What I can do? Sorry for my English. I used the Google translator.

  Read the article

• Configuring bridged network connection --- Windows 7 host, Ubuntu 10.04 guest --- VMWare Workstation 8

  - by H3br3wHamm3r81

  Here is my IPCONFIG /ALL from the host (Windows 7 64-bit): Here is my IFCONFIG from the guest (Ubuntu 10.04): To be honest, I don't have experience configuring a network between a host and a guest in VMWare (a virtual machine). I've searched high and low on the internet, but I haven't seen anything that can help. Perhaps I'm just not using the right keywords when I search. Nevertheless, does anyone here have any experience with establishing a network connection? Edit: One important note. I don't use DHCP to provide private addresses to the hosts on my LAN. I use "static" IP addresses on my internal network by configuring each IP address manually in the host's network configuration utility (I have TV's, XBOX 360, and a few PC's). I would like to configure the IP on the virtual machine guest manually as well. The reason is because my XBOX 360 only works properly using a static IP address. It will kick me off XBOX Live if it has one given by the router (via DHCP).

  Read the article

• Authentication error in LTSP client

  - by sat

  I am building a LTSP server with LDAP authentication for LTSP Clients. I have configured LDAP server also. When I try to login from LTSP client in GUI, I am getting No response from server, restarting. Then, It's restarting the GUI and comes to the login screen again. I thought that there could be a problem with LDAP authentication. But, When I try to login from Alt+Ctrl+F1 terminal in LTSP client, it is logged in successfully with LDAP user. LDAP Server and authentication is working fine. Even, after executing the below commands, still I am getting the same error. ltsp-update-sshkeys ltsp-update-kernels ltsp-update-image --arch i386 Whether I need to configure anything for GUI login from LTSP Client? How to fix this issue?

  Read the article

• suddenly cannot mount nfs share from windows 7

  - by bing

  I recently reinstalled my file server (moved from fedora to ubuntu server). Now I cannot mount my nfs share from windows 7, mounting from mac osx works fine. In windows I either keep getting "the semaphore timeout period has expired" or "an unexpected error has occured". Does ubuntu need some special magic to allow windows 7 to mount an nfs share? This is my exports file /home/bing/ 192.168.1.*(rw,async,insecure,no_subtree_check) /home/bing/mnt/EXTRN2 192.168.1.*(rw,async,insecure,no_subtree_check) /home/bing/mnt/EXTRN3 192.168.1.*(rw,async,insecure,no_subtree_check)

  Read the article

• Ubuntu Studio 10.4 boots to terminal mode only

  - by Don

  I did clean install from ISO DVD. It boots only to command line asking for login. After I login I enter STARTX and desktop appears and some of the studd actually works, but there are a lot of problems: there is no way to reboot or shut down except to stopx/logoff and enter shutdown sound system doesn't respond pulse audio volume control gives "connection failed, connection refused" DVD drives not available GDebi Package installer is grayed out and so I can't use it (but synaptic package manager works OK) Software Center won't start when clicked -- it just stops trying DBus cant run because it says /usr/local/var/run/dbus/system_bus_socket file not found (also /var/run/dbus/system_bus_socket file not found) There's just a lot of things wrong and I can't help but think something is missing or was mis-coded in the distro so that there are typos in some script somewhere. If anyone can tell me where to begin to untangle this mess I'd appreciate it, but I think it all begins when it can't start the GUI automatically and I need to enter STARTX.

  Read the article

• Running ubuntu 10.04 without a laptop's primary display

  - by riteshmnayak

  I have an IBM thinkpad(R50e) whose display is broken. I would still like to use the laptop by connecting it to an external monitor and keyboard/mouse. This is what I did: Removed the hard disk from the broken IBM Put the hard disk in the working IBM and installed 10.04 on it. It booted fine and I installed many packages and stuff. I put the hard disk back into the broken display IBM thinking I could use it by connecting it to an external monitor that I own. Well, it turns out that while booting, the display shows up but because the display shifts from the VGA display to the primary display mid-boot, the laptop does not boot. Is there a way in which I can force the laptop to not use its primary display while booting. I looked at Randr and also grub.conf settings but nothing seemed to work. Please help!

  Read the article

< Previous Page | 80 81 82 83 84 85 86 87 88 89 90 91  | Next Page >