Search Results

Search found 3043 results on 122 pages for 'offline browsing'.

Page 94/122 | < Previous Page | 90 91 92 93 94 95 96 97 98 99 100 101  | Next Page >

• SSL stops working on IIS7 after a reboot

  - by Mark Seemann

  I have a Windows 2008 Server with IIS7. Every time the server reboots, SSL stops working. Normal HTTP requests work fine, but any request to an HTTPS address gives the typical error message in the browser: Cannot find server or DNS I can temporarily fix it by opening IIS Manager and bring up the Bindings… window for the website in question. Then I select “https”, click on “Edit” then click “Ok” without making any changes to the settings. After doing this, browsing to https:// works again until the next reboot. This issue look as lot like the one described here, but according to the Certificates MMC snapin, the certificate in question does have a private key. I'm also pretty sure that I never installed the certificate in the personal store, but imported it straight into the machine store, but it's been a while... There's not a lot in the event log apart from the event ID 36870 also described in the post I linked to. Can anyone help me troubleshoot this issue so that SSL will work even after a server reboot?

  Read the article

• Need to Remove Exchange 2003 Server That Crashed During Transition to 2010

  - by ThaKidd

  As the title stated, we were running an Exchange 2003 server that we knew was going down soon so we purchased a second server and installed Exchange 2010 into the AD. We managed to move all of the mailboxes off of 2003 and also managed to get the Offline Address Book setup on 2010. At this point the 2003 server bit the dust and will no longer boot. Therefore we were unable to properly uninstall Exchange and remove the last 2003 server so it still exists in AD. As far as the clients are concerned, everything is working properly. However, when I run the Microsoft Exchange Profile Analyzer, I still see the old server and its Administrative Group. I am going to guess that since the old server is showing up in AD, I will not be able to raise Exchange or AD functionality (as the 2003 server was also the only AD DC) levels. I have forced the 2003 DC out of AD so that is no longer an issue. Old Setup: Windows 2003 Server Enterprise & Exchange 2003 Standard New Setup: Windows 2010 Server Enterprise & Exchange 2010 Standard Two Questions: How do you go about manually forcing the 2003 server and its administrative group out of AD? When that is finished, where do you raise the Exchange mode (can't find this for the life of me)?

  Read the article

• Dash (-) in directory listing

  - by Mazzy

  I've Googled around for this to no avail, I'm sure its just something simple but I have not been able to figure this out perhaps because searching in Google or SF for a "-" can be problematic. I had a strange directory listing show up the other day in my git repository within Drupal. Listing my sites directory looks like this: -sh-4.1$ ls -al total 52 drwxr-xr-x 5 (hide) (hide) 4096 Dec 6 16:15 . drwxr-xr-x 24 (hide) (hide) 4096 Dec 11 16:22 .. -rw-rw-r-- 1 (hide) (hide) 24271 Dec 6 15:57 – drwxrwxr-x 4 (hide) (hide) 4096 Sep 17 11:53 all drwxr-xr-x 3 (hide) (hide) 4096 Sep 17 11:54 default drwxrwxr-x 8 (hide) (hide) 4096 Dec 11 17:40 .git -rw-rw-r-- 1 (hide) (hide) 476 Sep 17 11:53 .gitignore -rw-rw-r-- 1 (hide) (hide) 81 Sep 17 11:53 README.md This "-" file cannot be opened and does not appear to be a symlink, although when I execute "cd -" I get this: -sh-4.1$ cd - /home/sites/dev1.(hide).com That is coincidentally or not the users home directory, and the site's root directory. The other strange this is this entry does not show up for any other user browsing this same directory. Nor does it show up for other users period in their Git directories. The entry cannot be removed via RM. Running Centos 6.2 by the way...

  Read the article

• Password-protected sharing allows access to users who have no account?

  - by romkyns

  Running Win7 on two computers in my LAN. Computer A has password-protected sharing enabled, and shares a folder. It has a single user account "Bob", and the Guest account is turned off. The network is workgroup-based. According to the descriptions of the "password-protected sharing" I could find, the only people who can access the shared folder via the LAN are those who know the username+password for the "Bob" account. However a second computer on the LAN is able to view this shared folder by simply browsing to Computer A. They don't need to enter any passwords or anything. The only user account registered on that PC is called "Jim", and has a different password from "Bob". How on earth is computer B able to view this shared folder? Is the popular description of the "password-protected sharing" feature inaccurate / did I misunderstand it big time? P.S. There is a possibility that the password for "Bob" has been entered on that PC once, and possibly the "remember password" box was checked. I've looked in the "Credential Manager" on both computers and there is nothing saved anywhere.

  Read the article

• Backup hardware and strategy on distributed Windows Server 2008 network

  - by CesarGon

  This question is a follow up to this. We have a Windows Server 2008 R2 domain over a network that spans two different buildings, linked by a 100-Mbps point-to-point line. Over 60 users work in the organisation. We are planning to use DFS folders and DFS replication for file serving across the organisation. The estimated data volume is over 2 TB, and will grow at approximately 20% annually. The idea is to set up a DFS file server in each building and use DFS so that all the contents stay replicated over the 100-Mbps link. We are now considering backup hardware and strategies. We are Dell customers and, after browsing the online Dell catalogue, I can see a number of backup hardware options. My main doubts are the following: Would you go for a tape library, disk backup, or are there other options worth considering? Would you perform batch backups (i.e. nightly) or would you use continuous backup (i.e. while users are working)? Would you use a dedicated backup server to which the tape library (or any other backup device) is attached, or is there any other alternative way of doing things? My experience with backup hardware and overall setup is limited, so I appreciate any good piece of advice that you may have. Thanks.

  Read the article

• Network Load Balancing, intermittent port problem

  - by Jimmy Chandra

  Trying to troubleshoot an intermittent problem. I think it might be related to an NLB issue. We are using Windows Network Load Balancing to balance load for our multiserver SharePoint front ends. Say... Web Front End 1 IP is 192.168.1.100 and Web Front End 2 IP is 192.168.1.101, the NLB is setup to load balance both WFE servers on any incoming traffic to the IP 192.168.1.200. Sometimes we got an intermittent issue where when we try to access the SharePoint site using 192.168.1.200:8080 (say the site is set up to run on port 8080) from a remote client, it will display page not found. Pinging the 192.168.1.200 will give responses, but when trying to telnet to 192.168.1.200:8080 it just won't connect. However, browsing the SharePoint site directly on individual WFE (192.168.1.100 and 192.168.1.101) show no problem whatsoever. My guess also (we didn't get a chance to try it yet, but I think it should work), if I try connecting remotely to individual server, it will respond just fine. But any attempt on trying to connect using the virtual IP (192.168.1.200) will fail miserably. Funny thing is, after a while it will return back to normal. Anyone had similar experience with this type of problem while implementing NLB before? We are doing this in a virtual environment.

  Read the article

• How do I configure permissions for a cluster share using Powershell on 2008?

  - by Andrew J. Brehm

  I have a cluster resource of type "file share" but when I try to configure the "security" parameter I get the following error (excerpt): Set-ClusterParameter : Parameter 'security' does not exist on the cluster object Using cluster.exe I get a better result, namely the usual nothing when the command worked. But when I check in Failover Cluster Manager the permissions have not changed. In Server 2003 the cluster.exe method worked. Any ideas? Update: Entire command and error. PS C:\> $resource=get-clusterresource testshare PS C:\> $resource Name State Group ResourceType ---- ----- ----- ------------ testshare Offline Test File Share PS C:\> $resource|set-clusterparameter security "domain\account,grant,f" Set-ClusterParameter : Parameter 'security' does not exist on the cluster object 'testshare'. If you are trying to upda te an existing parameter, please make sure the parameter name is specified correctly. You can check for the current par ameters by passing the .NET object received from the appropriate Get-Cluster* cmdlet to "| Get-ClusterParameter". If yo u are trying to update a common property on the cluster object, you should set the property directly on the .NET object received by the appropriate Get-Cluster* cmdlet. You can check for the current common properties by passing the .NET o bject received from the appropriate Get-Cluster* cmdlet to "| fl *". If you are trying to create a new unknown paramete r, please use -Create with this Set-ClusterParameter cmdlet. At line:1 char:31 + $resource|set-clusterparameter <<<< security "domain\account,grant,f" + CategoryInfo : NotSpecified: (:) [Set-ClusterParameter], ClusterCmdletException + FullyQualifiedErrorId : Set-ClusterParameter,Microsoft.FailoverClusters.PowerShell.SetClusterParameterCommand

  Read the article

• IIS 6 + ASP.NET web service - DW20 and stackoverflow exception

  - by pcampbell

  Consider an ASP.NET SOAP web service that starts up fine, but craters hard when receiving its first hit. Please note that this is deployment works in the Test environment, but not in the PreProd environment. Both are Windows 2003 SP3 + IIS 6 + ASP.NET 3.5. All up-to-date. The behaviour that we're seeing is: restart the site & app pool the app pool is configured to run under Network Service. browsing to the .asmx and .wsdl responds normally, as expected. send a normal well-formed SOAP request / normal payload to the web service 100% CPU usage after 5 seconds, the page request / site returns "Service Unavailable" no entry is created in the IIS log file (i.e. c:\windows\system32\logfiles\W3C-foo) the app pool ends up being stopped The processes that hit the CPU hard are dw20.exe. I am unsure why Dr Watson is involved here. Event Log shows an ASP.NET Runtime error: Task Manager: Event log text: EventType clr20r3, P1 w3wp.exe, P2 6.0.3790.3959, P3 45d6968e, P4 errormanagement, P5 1.0.0.0, P6 4b86a13f, P7 24, P8 0, P9 system.stackoverflowexception, P10 NIL. Questions Any thoughts on what this system.stackoverflow exception might be? Given that the code is the same between environments, might it be a payload problem? Could it be a configuration issue? You can see the name of my .NET assembly there in the exception message: "ErrorManagement"

  Read the article

• PC won't boot after hanging during Windows 8 automatic repair [closed]

  - by Mun

  I've got a custom built PC using an ASUS P5E motherboard and Intel Q6600 CPU. I plugged in my mp3 player to the USB port yesteday, and when I came back to the machine after about an hour or so, the Windows 8 automatic repair message was on the screen. It seemed to stick there for an hour, after which I decided to just hit reset and try and figure out what was going on. However, the machine rebooted to a black screen before even getting to the BIOS, with the monitor lights just blinking indicating there was no signal. Tried powering down completely, waiting a few minutes and then powering back up again with no difference; black screen with monitor lights blinking. Tried leaving it on for a while and then pinging from another machine or accessing it via something like LogMeIn, but everything showed the machine as being offline. There were also no error beeps or anything like that. Also tried unplugging all of the memory and rebooting and that also caused no error beeps. Removed one of the display cards and left the other one in there, and still only a black screen. I'm inclined to think that the motherboard or CPU is fried, but there is no indication of damage on any components and the CPU fan seems to be working fine as it always has, so overheating seems unlikely. It's also plugged into a surge protector. The motherboard also has a green light which still lights up. As everything was still working fine before hitting the reset button during Windows 8 automatic repair screen, at which point everything stopped working, it seems unlikely that this problem is down to component failure. Has anyone else experienced anything like this or have any ideas on what could be causing this behavior?

  Read the article

• Firefox 29 - how do I delete history entries visited fewer than x times

  - by lousyuser

  Context: I've been using my Firefox profile for a couple of years now. My history file has become huge, naturally. I got Firefox Sync set up between my main desktop PC and my laptop. HW configs: PC: i5-3450, 8 GB DDR3 RAM, Crucial M4 128 GB SSD laptop: Pentium SU4100, 4 GB DDR3 RAM, WD 5400 rpm HDD Accessing history entries when typing into the Awesome Bar on my desktop takes quite a long time despite the decent config, the laptop is even slower. The experience is quite unresponsive. I figured if I cleared the history up a little bit, I might avoid creating a new profile to speed things up. The question itself: to illustrate: Is there a way to delete all history entries that have been visited fewer than x (let's say 5) times and at the same time the recent visit is fewer than y (let's say 120) days old? afaik the history file is some kind of SQL database, but I'm not really sure how the data is saved, if there's a "safe way" to edit it and what the query to do what I need would look like. Thanks in advance for any help. I kept browsing through previous SuperUser questions to see if I could find relevant information. "In my Firefox profile directory, there is a filed named places.sqlite. Opening it with sqlite reveals (amongst others) the tables moz_places and moz_historyvisits. It seems that moz_historyvisits uses the primary of moz_places to refer to the URLs." As I'm unfamiliar with databases, I don't really understand the way the two tables mentioned in the quote are related. screenshot of a part of the tables I've noticed the visit_count is in a standard format, making it easy to work with. The last_visit_date looks encrypted to my naked eye, but I can't see in which way. Hope that helps, I'm at my wits' end.

  Read the article

• Static Network configuration with bridge in CentOS 6.2

  - by Kyle

  I have a server with CentOS 6.2 installed, I want to use it as a VM host to run some windows installations for development purposes. I wanted to be able to directly RDP and serve websites from IIS on these windows server installations, so I figured I would set it up as bridged networking. I have been struggling with this all morning, usually the result being that when I brought up the bridge interface all network connectivity to the CentOS would go away, however, I think I finally have that all figured out. However, here's what happens. The eth0 and br0 interfaces are defined in /etc/sysconfig/network-scripts with ifcfg-eth0 and ifcfg-br0. I DO NOT have ifup or ifdown or any other files for these interfaces, I have not found if they are needed. I can login and use firefox to browse the web, however, running ifconfig reveals that my eth0 does not have an IPAddress, but the br0 does. I can actually RDP into the Windows installation, and browse the internet from there as well, but I cannot directly connect(via putty, vnc, nor viewing web pages) to the CentOS box. Any idea what's up? ifcfg-eth0 DEVICE=eth0 BOOTPROTO=none IPADDR=192.168.1.20 GATEWAY=192.168.1.1 NETMASK=255.255.255.0 NETWORK=192.168.1.0 ONBOOT=yes BRIDGE=br0 ifcfg-br0 DEVICE=br0 TYPE=Bridge BOOTPROTO=static DNS1=192.168.1.1 DNS2=8.8.8.8 GATEWAY=192.168.1.1 IPADDR=192.168.1.2 NETMAS=255.255.255.0 ONBOOT=yes I know some of the options are inconsistent (DNS and BOOTPROTO) because I tried changing those in the eth0 file to make it work, and the changes haven't adversly affected web browsing or the other functionality Thank you!

  Read the article

• How to set JS source directory in apache2?

  - by highBandWidth

  I am trying to run a very basic webserver for development/debugging. The static HTML seems to be delivered correctly, but it seems that the JavaScript libraries are not being delivered to the browser. The page HTML says something like <html> <head> <script type='text/javascript' src="/lib/json.js"></script> ... Now, I have set up a link for /lib/ in my httpd.conf as: Scriptalias /lib/ "/SomeFolder/lib/" When I do this, it can't fetch the files because this is what I see in my apache error log: ... [error] [client ::1] client denied by server configuration: /SomeFolder/lib/json.js, referer: http://localhost/SomeSite It seems that apache is not allowing access to the folder, so I add this to httpd.conf: Directory "/SomeFolder/lib/"> Allow from all </Directory> After this, browsing the page still does not run the JS, instead I see the following error in my apache error log: [error] [client ::1] (13)Permission denied: exec of '/SomeFolder/lib/json.js' failed, referer: http://localhost/SomeSite So now, it seems that apache is trying to run the JS files on the server like a cgi script or something. But I have not made that folder a cgi-bin folder. The only lines where SomeFolder is mentioned by name is in these lines in httpd.conf: Scriptalias /lib/ "/SomeFolder/lib/" Directory "/SomeFolder/lib/"> Allow from all </Directory>

  Read the article

• Mac Mini's internet very slow, every other device fine (PC, iPhone, Xbox 360)

  - by alex

  I recently haven't used my Mac Mini for about 5 days (however it was left on). I seem to be able to connect and get great download / upload speeds through my PC, Xbox 360, iPhone and parents' laptop. However, my Mac Mini is very slow. OS X's Mail.app is downloading mail at 0.4kbps and then dropping to 0. Skype file transfers are doing the same. Browsing the net is a terrible experience. It is taking 30 seconds or more to download basic pages. All of my devices connect wirelessly to a Netgear router / modem. I have tried giving the Mac Mini a manual IP, and renew DHCP lease, as well as flush DNS in Terminal. I have also rebooted the router / modem twice, and the Mac Mini twice. Do you know what could be causing this? Thanks Update This is very weird. It is also very slow accessing localhost (setup through MAMP) and also slow to access the Netgear router config pages.

  Read the article

• Should I use Evernote or Org-mode for taking notes?

  - by tobeannounced

  I am looking for an app that will help me manage my notes, and after coming across Org-mode, I was wondering whether Org-mode's functionality is strong enough that it can remove the need for me to use another note taking app (because org is more of a task management app), such as Evernote. My wishes for a note taking app are: can be accessed offline in some form, eg through an iPhone app or desktop client Org-Mode and Evernote can both do this, however it seems like MobileOrg is more aimed at tasks, rather than notes? If this is the case, I probably would use Evernote in addition to MobileOrg. I can clip web content into easily for research Evernote has the browser extension, how is it with Org-Mode? I know I can use c-c c-l, but how suited is it really for taking notes on stuff I am browsing in Chrome/Firefox? has voice notes on the iPhone and computer too, if possible Org-Mode cannot do this on the iPhone, on the computer could I record audio externally and then link the files in? I can add notes too on my iPhone & computer while not connected to the internet both can do this. The types of notes I am likely to have include: howtos/things I have learnt, documentation on my setup/stuff, research on things I may do in the future, ideas, and task specific notes. I have thought about where I would want to access each of these notes and will post that here if you think it would help. So, is Org-mode strong enough in note-taking and the requirements I listed that I can avoid the need to use a separate tool for taking notes?

  Read the article

• Extend RAID 1 (HP SmartArray P410i) running Linux

  - by Oliver

  I took over a fairly simple server setup with the following RAID 1 config running Ubuntu 11.10 (Kernel 3.0.0-12-server x86_64): => ctrl all show config Smart Array P410i in Slot 0 (Embedded) (sn: removed) array A (SAS, Unused Space: 1335535 MB) logicaldrive 1 (279.4 GB, RAID 1, OK) physicaldrive 1I:1:1 (port 1I:box 1:bay 1, SAS, 1 TB, OK) physicaldrive 1I:1:2 (port 1I:box 1:bay 2, SAS, 1 TB, OK) Initially there were two 300GB disks that got replaced by 1TB disks and I now have to extend the logical volume to use that extra space. However, when trying to do so I get the following warning: => ctrl slot=0 ld 1 modify size=max Warning: Extension may not be supported on certain operating systems. Performing extension on these operating systems can cause data to become inaccessible. See ACU documentation for details. Continue? (y/n) Is it safe to say yes or am I at risk of corrupting the file system / loosing data? Rearranging and extending the file system afterwards shouldn't be an issue as I can take the server offline and boot from a gparted live disk. Here's the config of the RAID controller in use: => ctrl all show detail Smart Array P410i in Slot 0 (Embedded) Bus Interface: PCI Slot: 0 Serial Number: removed RAID 6 (ADG) Status: Disabled Controller Status: OK Hardware Revision: Rev C Firmware Version: 5.12 Rebuild Priority: Medium Expand Priority: Medium Surface Scan Delay: 15 secs Surface Scan Mode: Idle Wait for Cache Room: Disabled Surface Analysis Inconsistency Notification: Disabled Post Prompt Timeout: 0 secs Cache Board Present: False Drive Write Cache: Disabled SATA NCQ Supported: True And the partition table: Number Start End Size Type File system Flags 1 1049kB 274GB 274GB primary ext4 boot 2 274GB 300GB 25.8GB extended 5 274GB 300GB 25.8GB logical linux-swap(v1)

  Read the article

• Best photo management software?

  - by Niels Basjes

  Hi, What I would like is a single piece of software (or a smart combination of tools) that allow me to manage my photos in a better way than what I've found so far. 1. Tags Primarily I need a way of tagging the images. So I can manually tag photos the same way we tag questions here at SO/SF/SU. I want this software to place a lot of the tags automagically (obvious things like date and resolution). 2. Face recognition What I would really like is that this software has a feature that it can recognize faces in images and places tags with the name of the person. So far I've only heard of one online photo system that can do that (Picasa) and not yet of any offline tool. 3. Version database I must have some way of having a central GIT/SVN/... that contains all images. I have had a harddrive corruption a few years ago and it took me a long time to figure out which images had been damaged. I always want to be able to go back to what the camera produced. 4. Website I want to be able to generate a website (few 'tag' specific websites) based on the actual content. 5. Easy bulk uploading Many photo tools have a one on one uploading option. I prefer simply 'throwing' my images on a file server under Linux (Samba) and let the system automagically integrate, tag, recognize, etc. all images. Ok, I know these are a bit much. Perhaps you guy's have some suggestions about existing tools that can make this possible. Or even a complete system that does this. EDIT: To clarify on the OS. I prefer Linux for any 'server' task and Windows XP for any 'desktop' task. Thanks for all your input. Niels Basjes

  Read the article

• Sharing files between 2 different routers

  - by Chris

  I realize this has been asked before and I have read as much as I could find on the topic but I still need help with this because there are so many different approaches and the ones I am trying aren't working. So I have 2 routers, lets call them A and B. Both have a wireless feature and are active. A is in the basement and receives the internet. There is a TV on the ground floor that is connected to A through an ethernet wire. B is upstairs and gets the internet from A through an ethernet wire. Connected to B, is a desktop running Plex Media Server. What I want to do is make sure devices connected to both routes can access the Plex Media Server. So what I have read is that I should plug in the ethernet wire connecting B to a into a LAN port instead of the WAN port. After that I should turn off DHCP. I have tried this and B stops receiving internet. What am I doing wrong? Another thing I have read is to use Router B in bridge mode but Router B is running openwrt and I have QoS on it so gaming/VoIP/browsing is unaffected by heavy downloading/uploading. I would prefer to keep this active. I realize it might be ineffective if a device in Router A is doing some hardcore downloading but all that stuff is done on Router B anyway so it doesn't matter. Router A can't get openwrt because it is a shitty one provided by Bell. So, how do I proceed with this?

  Read the article

• Can't connect to research.microsoft.com on home Qwest DSL connection

  - by rakingleaves

  I have a puzzling issue regarding accessing research.microsoft.com from my home Qwest DSL connection. By default, I frequently get timeouts when accessing research.microsoft.com from Firefox, Safari, or Chrome on my Mac. I also cannot access the site from Internet Explorer in a Windows VM. However, I am able to access the site through proxify.com, so I know the site is not down. Furthermore, I haven't noticed problems accessing other sites (in particular, www.microsoft.com works fine). Also, I can access research.microsoft.com when I'm connected to networks other than my home Qwest DSL connection. Together, the above make me suspect a problem with either my router (Airport Express) or, more likely, my ISP. Anyone have any thoughts on how I can narrow down the problem further? I could call my ISP and tell them the above, but my feeling is that probably won't get me very far. I can get by browsing research.microsoft.com through a proxy, but it would be nice to figure out what's going on here and fix the problem. Oh, the only relevant discussion I found via Google was here: http://forums.whirlpool.net.au/forum-replies-archive.cfm/1311734.html Update: Thanks to those who have tried to help! I found one other thing while Googling that may be vaguely relevant: http://thedaneshproject.com/posts/supportmicrosoftcom-not-working-behind-squid/ Disabling the Accept-Encoding headers in Firefox actually didn't make a difference for me. I just thought the above might spark some other ideas about how mishandling of HTTP headers somewhere might be causing this problem. Thanks again! Another update: In case anyone is still thinking about this; I've found that I can't surf research.microsoft.com using the links text-based browser, but I can reliably download individual files with wget. Maybe that helps?

  Read the article

• Regular Windows 7 BSOD with Shrew VPN client

  - by Junto

  The Shrew VPN client appears to be a good alternative to the Cisco VPN Client on x64 Windows 7. However, since installing it I've seen fairly regular BSODs. Minidump attached: Microsoft (R) Windows Debugger Version 6.11.0001.404 AMD64 Copyright (c) Microsoft Corporation. All rights reserved. Loading Dump File [D:\Temp\020810-23431-01.dmp] Mini Kernel Dump File: Only registers and stack trace are available Symbol search path is: SRV*d:\symbols*http://msdl.microsoft.com/download/symbols Executable search path is: Windows 7 Kernel Version 7600 MP (8 procs) Free x64 Product: WinNt, suite: TerminalServer SingleUserTS Built by: 7600.16385.amd64fre.win7_rtm.090713-1255 Machine Name: Kernel base = 0xfffff800`0285f000 PsLoadedModuleList = 0xfffff800`02a9ce50 Debug session time: Mon Feb 8 18:08:12.887 2010 (GMT+1) System Uptime: 0 days 7:52:06.120 Loading Kernel Symbols ............................................................... ................................................................ .............. Loading User Symbols Loading unloaded module list .... ******************************************************************************* * * * Bugcheck Analysis * * * ******************************************************************************* Use !analyze -v to get detailed debugging information. BugCheck A, {0, 2, 0, fffff800028d50b6} Unable to load image \SystemRoot\system32\DRIVERS\vfilter.sys, Win32 error 0n2 *** WARNING: Unable to verify timestamp for vfilter.sys *** ERROR: Module load completed but symbols could not be loaded for vfilter.sys Probably caused by : vfilter.sys ( vfilter+29a6 ) Followup: MachineOwner Machine is a brand spanking new Dell Precision T5500. Superuser appears to have several recommendations for the Shrew VPN Client as an alternative to the Cisco VPN client on 64 bit machines, so I wondered if anyone here has seen this problem and possibly found a solution to the problem? I've decided to run the VPN client under Windows 7 compatibility mode for the moment (Vista SP2) with administrator privileges to see if it makes a difference. Oddly, the VPN doesn't necessarily need to be connected. I've noticed it when browsing using Google Chrome and Internet Explorer, usually when I open up a new tab. If it carries on I think I'll be forced to shell out the 120 EUR for the NCP Client instead.

  Read the article

• VMWare Host Not Responding - VMs are Disconnected (ESXi 3.5)

  - by EyeonTech

  I have inherited a VMWare environement ESX v3i 3.5. I am not fluent with VMWare ESXi so bare with me. Two days ago, when I opened Virtual Centre, one of the Hosts showed up as Not Responding. The error I am seeing is:----- Unable to acquire licenses because license source is unavailable: The license manager has not been started yet, the wrong port@host or license file is being used, or the port or hostname in the license file has been changed. What I have tried: I have Stopped and Started the license server within the application. When I do this, I am able to disconnect the host in Virtual Centre and reconnect. This brings the host back online, but a few minutes later, the host goes to a not responding state again. I have rebooted the server with the Licensing software installed. While browsing Google, I have not been able to find any steps I feel comfortable performing and I would like the opinion of the VMWare pros. Where are the log files I should be looking at to correctly determine what is going on? Has anyone seen this behaviour and how did you resolve it? Thank you

  Read the article

• Issue with SSL using HAProxy and Nginx

  - by Ben Chiappetta

  I'm building a highly available site using a multiple HAProxy load balancers, Nginx web serves, and MySQL servers. The site needs to be able to survive load balancer or web servers nodes going offline without any interruption of service to visitors. Currently, I have two boxes running HAProxy sharing a virtual IP using keepalived, which forward to two web servers running Nginx, which then tie into two MySQL boxes using MySQL replication and sharing a virtual IP using heartbeat. Everything is working correctly except for SSL traffic over HAProxy. I'm running version 1.5 dev12 with openssl support compiled in. When I try to navigate to the virtual IP for haproxy over https, I get the message: The plain HTTP request was sent to HTTPS port. Here's my haproxy.cfg so far, which was mainly assembled from other posts: global log 127.0.0.1 local0 log 127.0.0.1 local1 notice # log 127.0.0.1 local0 user haproxy group haproxy daemon maxconn 20000 defaults log global option dontlognull balance leastconn clitimeout 60000 srvtimeout 60000 contimeout 5000 retries 3 option redispatch listen front bind :80 bind :443 ssl crt /etc/pki/tls/certs/cert.pem mode http option http-server-close option forwardfor reqadd X-Forwarded-Proto:\ https if { is_ssl } reqadd X-Proto:\ SSL if { is_ssl } server web01 192.168.25.34 check inter 1s server web02 192.168.25.32 check inter 1s stats enable stats uri /stats stats realm HAProxy\ Statistics stats auth admin:********* Any idea why SSL traffic isn't being passed correctly? Also, any other changes you would recommend? I still need to configure logging, so don't worry about that section. Thanks in advance your help.

  Read the article

• Oracle Database Recovery Problem

  - by Palani

  I am very new to Oracle, and trying to restore a oracle 8i database on win 2000 server. I have one week old database backup (backup taken with exp command), and i want to restore it now. Now I am unable to login through sqlplus (got shutdown in progress error) I have a backup and i want to restore it, but oracle is not starting at all, and 'imp' command is failing. I started sqlplus / as sysdba and following is the log of what i am trying to do. Can some one guide me further. SQL> shutdown immediate; ORA-01109: database not open Database dismounted. ORACLE instance shut down. SQL> startup; ORACLE instance started. Total System Global Area 143423516 bytes Fixed Size 75804 bytes Variable Size 58105856 bytes Database Buffers 85164032 bytes Redo Buffers 77824 bytes Database mounted. ORA-01589: must use RESETLOGS or NORESETLOGS option for database open SQL> shutdown immediate; ORA-01109: database not open Database dismounted. ORACLE instance shut down. SQL> startup mount; ORACLE instance started. Total System Global Area 143423516 bytes Fixed Size 75804 bytes Variable Size 58105856 bytes Database Buffers 85164032 bytes Redo Buffers 77824 bytes Database mounted. SQL> alter database open; alter database open * ERROR at line 1: ORA-01589: must use RESETLOGS or NORESETLOGS option for database open SQL> alter database open resetlogs; alter database open resetlogs * ERROR at line 1: ORA-01245: offline file 1 will be lost if RESETLOGS is done ORA-01110: data file 1: 'C:\ORACLE\ORADATA\ABCD\SYSTEM01.DBF'

  Read the article

• IIS permission configuration issue

  - by Dan

  Sorry the title of this question is a little ambiguous but I don't really have any idea where the issue lies - I'm seeking some clarification of the server error logs. Basically, I had a dedicated server running Windows 2003 and Plesk (v8 I think). Last week the server hardware failed and the entire thing had to be rebuilt from scratch. New hardware was put in, new operating system (Win2008), new Plesk installation (v9.5), new software (MSSQL etc) then all data ported over manually from old C and D drives to restore all 30 client sites. It was hell! All has been okay for a couple of days now but about an hour ago POP! Suddenly all sites went down giving a 500 error. Restarting all services eventually brought everything back online, but I'm now living in total fear. It can - and probably will - happen again. The guys on support gave me the following errors from the server log: The Template Persistent Cache initialization failed for Application Pool 'ASP.NET v4.0 Classic' because of the following error: Could not create a Disk Cache Sub-directory for the Application Pool. The data may have additional error codes.. The worker process for application pool 'domain1.com(domain)(2.0)(pool)' encountered an error 'Cannot read configuration file ' trying to read configuration data from file '\\?\C:\inetpub\temp\apppools\domain1.com(domain)(2.0)(pool).config', line number '0'. The data field contains the error code. The worker process for application pool 'PleskControlPanel' encountered an error 'Cannot read configuration file ' trying to read configuration data from file '\\?\C:\inetpub\temp\apppools\PleskControlPanel.config', line number '0'. The data field contains the error code. The support guys are so ambiguous about this and it scares me horribly. Can anyone positively identify the cause of this error which lead to all client website going offline? What can be done to prevent it from happening again? Any pointers would be very much appreciated! Thanks folks...

  Read the article

• Search for partial IP address using Windows Search?

  - by Dr. Dre

  I have a folder, c:\projects\, added to Windows Index. I know the indexing is working because I search for stuff in this folder all the time and the results come up very fast, and I've never noticed any accuracy problem until now. (I have had to tweak Indexing options to expand which file types have their contents indexed rather than just the file name, etc, but after that Search has worked pretty well for me). I've encountered a problem while trying to search for references to a particular IP address subnet. I'm trying to find all references to IP's with the pattern "192.168.220.xxx" (AKA, the 192.168.220.0/24, AKA 192.168.220.0/255.255.255.0 IP/netmask). Within Windows Explorer: c:\projects**.* is indexed c:\projects\work\project1\network_list.txt contains several "192.168.220.xxx" IP's Indexing status says all items are indexed (193,000 items). When I try to search for partial IP match, there are no search results. Tried searching for: 192.168.220, 192.168, 192.168.220., 192.168.220., 192.168.220.?, 192.168.220.??, 192.168.220.???, 192.168., 192.168.. Also tried variants of all the above surrounded with double quotes. All the searches returned 0 results. Within MS Outlook 2007: My mailbox, and all my offline .pst's are indexed. I search in Outlook pretty frequently, so I'm pretty sure indexed searches work across inbox and all .pst's. Indexing status in Outlook says all items are indexed. I also have references to these IP's in email, and I'd like to find all of them. Basically same deal as above, can't search for "192.168.220.xxx" IP's. Any way to fix this?

  Read the article

• How do I remove a USB drive's write protection?

  - by nate

  I have a SanDisk Cruser Blade USB stick that suddenly seems to be write protected. I tried running DiskPart but after I write the command "attributes disk clear readonly" it displays this: Microsoft DiskPart version 5.1.3565 ADD - Add a mirror to a simple volume. ACTIVE - Marks the current basic partition as an active boot partition. ASSIGN - Assign a drive letter or mount point to the selected volume. BREAK - Break a mirror set. CLEAN - Clear the configuration information, or all information, off the disk. CONVERT - Converts between different disk formats. CREATE - Create a volume or partition. DELETE - Delete an object. DETAIL - Provide details about an object. EXIT - Exit DiskPart EXTEND - Extend a volume. HELP - Prints a list of commands. IMPORT - Imports a disk group. LIST - Prints out a list of objects. INACTIVE - Marks the current basic partition as an inactive partition. ONLINE - Online a disk that is currently marked as offline. REM - Does nothing. Used to comment scripts. REMOVE - Remove a drive letter or mount point assignment. REPAIR - Repair a RAID-5 volume. RESCAN - Rescan the computer looking for disks and volumes. RETAIN - Place a retainer partition under a simple volume. SELECT - Move the focus to an object. It's like when you type help at the DiskPart prompt, so how do I get past this? This problem started when I plugged the stick into a laptop which had viruses, if that's any help.

  Read the article

< Previous Page | 90 91 92 93 94 95 96 97 98 99 100 101  | Next Page >