Search Results

Search found 2794 results on 112 pages for 'peu ping'.

Page 98/112 | < Previous Page | 94 95 96 97 98 99 100 101 102 103 104 105  | Next Page >

• cannot connect to vpn server (error 721)

  - by callmeblessed

  Hi I got 2 internet connections in my computer. One is using 3.5G HSDPA modem (vodafone huawei e220) and the other using mobile phone (cdma zte c261). Both are using different ISP and i have both. at the moment, i can connect to my office vpn using the HSDPA modem one. But when i tried to use cdma modem (dial up - mobile phone modem), i am just able to get "verifying username and password" and then after a few minutes it display error : Error 721 The Remote Computer didn't respond. I tried to ping into my office ip address, it got good result but still cannot connect to the vpn. I tried to turn off all my firewall (i'm using commodo) and has no response as well. In my cdma mobile phone modem Network connections I tried to allow iNternet connection sharing as well ... and turn on all Internet Protocol TCP/IP, File & Printer Sharing & Client for microsoft networks. But all of my effort has no effect. How to fix this problem ? note: my office using windows vpn as well. thank you .

  Read the article

• ipv6 with KVM on debian

  - by Eliasdx

  I have trouble setting up IPV6 on my Proxmox (KVM) server: My ISP sent me this information(xxx=placeholder): IPs: 2a01:XXX:XXX:301:: /64 Gateway: 2a01:XXX:XXX:300::1 /59 This is the interface setup on the host server: auto vmbr1 iface vmbr1 inet static address 178.XX.XX.4 broadcast 178.XX.XX.63 netmask 255.255.255.192 pointopoint 178.XX.XX.1 gateway 178.XX.XX.1 bridge_ports eth0 bridge_stp off bridge_fd 0 iface vmbr1 inet6 static address 2a01:XXX:XXX:301::2 netmask 64 up ip -6 route add 2a01:XXX:XXX:300::1 dev vmbr1 down ip -6 route del 2a01:XXX:XXX:300::1 dev vmbr1 up ip -6 route add default via 2a01:XXX:XXX:300::1 dev vmbr1 down ip -6 route del default via 2a01:XXX:XXX:300::1 dev vmbr1 On the guest: auto eth0 iface eth0 inet static address 178.xx.xx.47 netmask 255.255.255.255 broadcast 178.xx.xx.63 gateway 178.xx.xx.1 pointopoint 178.xx.xx.1 iface eth0 inet6 static pre-up modprobe ipv6 address 2a01:XXX:XXX:301::2:2 netmask 64 up ip -6 route add 2a01:XXX:XXX:300::1 dev eth0 down ip -6 route del 2a01:XXX:XXX:300::1 dev eth0 up ip -6 route add default via 2a01:XXX:XXX:300::1 dev eth0 down ip -6 route del default via 2a01:XXX:XXX:300::1 dev eth0 Ipv4 works on both host and guest but Ipv6 only works "sometimes". It's up for minutes and then down again until I change something. However I can actually ping the host and the guest from both host and guest. host:~# ip -6 neigh 2a01:XXX:XXX:301::100:2 dev vmbr1 lladdr 00:50:56:00:00:e0 REACHABLE 2a01:XXX:XXX:300::1 dev vmbr1 lladdr 00:26:88:76:18:18 router STALE host:~# ip -6 route 2a01:XXX:XXX:300::1 dev vmbr1 metric 1024 mtu 1500 advmss 1440 hoplimit 4294967295 2a01:XXX:XXX:301::/64 dev vmbr1 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 fe80::/64 dev vmbr0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 fe80::/64 dev eth0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 fe80::/64 dev vmbr1 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 fe80::/64 dev tap101i1d0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 default via 2a01:XXX:XXX:300::1 dev vmbr1 metric 1024 mtu 1500 advmss 1440 hoplimit 4294967295 Does someone know why it isn't working? And is there a way to configure multiple v6 IPs from the same subnet so I can dedicate IPs to websites on a server with multiple virtualhosts?

  Read the article

• Vlan on DD-WRT v24 filesharing without internet

  - by user148888

  I'm planning to do a vlan with shared files without internet. my vlan is working correctly until I could lock the internet but I can not share files only I can ping from 172.168.1.x to 172.168.2.x but not backward. can u help me please?? This is my config. WRT54g DD-wrt v24 vlan0 eth 1,2,3 172.168.1.1/24 vlan1 Wan vlan2 eth 4 172.168.2.1/24(don't want internet here just Lan Conection) Pc (my pc) 172.168.1.10/24 gtway 172.168.1.1 (with internet) Ubiquity Nanostation loco M2 172.168.2.20/24(AP)(connect to eth 4 vlan2)(don't want internet here) Ubiquity Nanostation loco M2 172.168.2.21/24(Client)(don't want internet here) Friend pc 172.168.2.115/24(connected from the client)(don't want internet here) Any Help Please.. ![Lan Map][1] ![Vlan Config1][2] ![Vlan Config2][3] ![Vlan Config3][4] ![Command to block internet][5] [url=http://imageshack.us/photo/my-images/194/lanxl.jpg/][img=http://imageshack.us/a/img194/4197/lanxl.th.jpg][/url] [url=http://imageshack.us/photo/my-images/600/commandmf.jpg/][img=http://imageshack.us/a/img600/9530/commandmf.th.jpg][/url] [url=http://imageshack.us/photo/my-images/811/57398524.jpg/][img=http://imageshack.us/a/img811/1917/57398524.th.jpg][/url] [url=http://imageshack.us/photo/my-images/717/48064277.jpg/][img=http://imageshack.us/a/img717/829/48064277.th.jpg][/url] [url=http://imageshack.us/photo/my-images/685/21456517.jpg/][img=http://imageshack.us/a/img685/256/21456517.th.jpg][/url]

  Read the article

• ipv6 with KVM on debian

  - by Eliasdx

  I have trouble setting up IPV6 on my Proxmox (KVM) server: My ISP sent me this information(xxx=placeholder): IPs: 2a01:XXX:XXX:301:: /64 Gateway: 2a01:XXX:XXX:300::1 /59 This is the interface setup on the host server: auto vmbr1 iface vmbr1 inet static address 178.XX.XX.4 broadcast 178.XX.XX.63 netmask 255.255.255.192 pointopoint 178.XX.XX.1 gateway 178.XX.XX.1 bridge_ports eth0 bridge_stp off bridge_fd 0 iface vmbr1 inet6 static address 2a01:XXX:XXX:301::2 netmask 64 up ip -6 route add 2a01:XXX:XXX:300::1 dev vmbr1 down ip -6 route del 2a01:XXX:XXX:300::1 dev vmbr1 up ip -6 route add default via 2a01:XXX:XXX:300::1 dev vmbr1 down ip -6 route del default via 2a01:XXX:XXX:300::1 dev vmbr1 On the guest: auto eth0 iface eth0 inet static address 178.xx.xx.47 netmask 255.255.255.255 broadcast 178.xx.xx.63 gateway 178.xx.xx.1 pointopoint 178.xx.xx.1 iface eth0 inet6 static pre-up modprobe ipv6 address 2a01:XXX:XXX:301::2:2 netmask 64 up ip -6 route add 2a01:XXX:XXX:300::1 dev eth0 down ip -6 route del 2a01:XXX:XXX:300::1 dev eth0 up ip -6 route add default via 2a01:XXX:XXX:300::1 dev eth0 down ip -6 route del default via 2a01:XXX:XXX:300::1 dev eth0 Ipv4 works on both host and guest but Ipv6 only works "sometimes". It's up for minutes and then down again until I change something. However I can actually ping the host and the guest from both host and guest. host:~# ip -6 neigh 2a01:XXX:XXX:301::100:2 dev vmbr1 lladdr 00:50:56:00:00:e0 REACHABLE 2a01:XXX:XXX:300::1 dev vmbr1 lladdr 00:26:88:76:18:18 router STALE host:~# ip -6 route 2a01:XXX:XXX:300::1 dev vmbr1 metric 1024 mtu 1500 advmss 1440 hoplimit 4294967295 2a01:XXX:XXX:301::/64 dev vmbr1 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 fe80::/64 dev vmbr0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 fe80::/64 dev eth0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 fe80::/64 dev vmbr1 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 fe80::/64 dev tap101i1d0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 default via 2a01:XXX:XXX:300::1 dev vmbr1 metric 1024 mtu 1500 advmss 1440 hoplimit 4294967295 Does someone know why it isn't working? And is there a way to configure multiple v6 IPs from the same subnet so I can dedicate IPs to websites on a server with multiple virtualhosts?

  Read the article

• Unusable network, packet losses between router and NIC

  - by KáGé

  I have this setup: Gigabyte P35-DS3P motherboard Asus NX1101 PCI network card (the one on the motherboard got fried a few years ago by a power surge) Asus RT-N16 router Windows 7 x64 I think the other specs are irrelevant here, but I'll post them if you say so. Until a week ago everything was fine, but then my network became unusable: websites start loading but timeout before anything would come through (true for the web interface of the router as well), I can't reach the computer from my notebook and Windows' ping utility measures a ~50% packet loss between the computer and the router. Pinging localhost is good. The router works completely fine when wired to my notebook. I also tested different ports on the router, different cables, different router and connecting directly to the modem, but it's still the same. Sometimes it works for a few minutes right after turning on the machine, but then it becomes crap again, but mostly it's useless from the start. I've tried updating the firmware on the router, updating the driver for the network card (after which I started getting BSoDs in every 15 minutes), reinstalling Windows, swapping to Fedora 15 but none of them changed anything. Does this mean that the network card is dying, or could it be something else? If it's the card, what model do you recommend as a replacement? (Could be PCI or PCI-Ex x1) Thanks for your help.

  Read the article

• Juniper router dropping pings to external interface

  - by Alexander Garden

  My organization has a Juniper SSG20-WLAN that routes our traffic to the outside world. We've been having intermittent problems with our internet connection so I wrote up a Python script to ping the internal interface of the router, the external interface, a couple of our internal servers, the ISP router our router talks to, their upstream provider, and Google and Yahoo for good measure. It does that about every minute. What I have found is that when our internet goes out, our Juniper router ceases responding to pings on the external interface. Everything past that is, of course, unreachable. The internal interface and our internal servers continue to echo back without interruption. None of the counters indicate dropped packets of any type. They all look normal. The logs complain about VIP servers being unavailable but otherwise nothing indicative of network issues. My questions are these: Does this exonerate our ISP? Or, contrawise, might a problem with the connection be causing the external interface to go down? Is there somewhere else in the SSG20, beside the system log and counters, that might help me track down info on the problem? UPDATE: Turned out that one of the switches between my monitoring box and the router was a router itself, and occasionally diverting from the gateway to itself. Kudos to those who made suggestions along those lines. Not really sure which answer to mark as accepted, as it was really stuff in the comments that turned out to be right. Thanks for the suggestions.

  Read the article

• Hyper-V: Dedicated NIC for Guests VMs

  - by TheLizardKing

  I have two NIC cards and created a private virtual network for my virtual machines and unchecked "Allow management operating system to share this network adapter" which basically turns my Guest NIC into this sorta shell of a NIC card on the host machine and the only thing checked in it's properties is "Microsoft Virtual Network Switch Protocol" which I am fine with. Everything works and everything is connected. My issue is that for some reason my guest (Ubuntu Server with legacy network drivers) is not talking properly to my DHCP server. Specifically my DHCP server reserves the guest's IP address using it's MAC address but the guest isn't picking it up. It's picking up any old IP it can get and I can't even ping the hostname from another PC on the network but it pings fine if I use the IP. I see the guest showing up in my DHCP table but I can't get the reservation to stick. Is there some reason it's only partially communicating with my DHCP server? Pinging it's hostname on itself reveals it's using 127.0.0.1 instead of it's network IP. Is this an issue with the legacy drivers used in Hyper-V?

  Read the article

• Server 2003 and XP Client; Why are HTTP connections being silently dropped.

  - by Asa Yeamans

  On my network, my edge-router, a windows 2003 r2 server router with all the latest updates, will drop packets, but only under specific circumstances. I have troubleshot and isolated it down to the most simple configuration i can. There is NO NAT involved. Only fully-public IP addresses. No Firewalls are running either, all ahve been disabled. no packet filters on any interfaces anywhere either. I have a single Windows XP virtual machine and my edge-router(the windows 2003 r2 server, and also a virtual machine) running on a windows 2008 x64 r2 system (running virtual server 2005 as i dont have Intel-VT compatible chip yet). The edge router can access any external http site just fine, no issues. However the windows XP machine is only able to access certain sites. These work: www.google.com www.txstate.edu www.workintexas.com www.thedailywtf.com . These Dont: www.yahoo.com www.utexas.edu en.wikipedia.org slashdot.org www.bing.com. I have removed all possibility of DNS issues by connecting with net-cat from the XP box and sending GET /\r\nHost: \r\n\r\n and that connection replicates the issue as well. The network setup: My statically assigned IP block: x.x.x.168/29 DSL Modem -----PPPoE Connection---- x.x.x.169[EdgeRouter] [EdgeRouter]x.x.x.170 -----Virtual Ethernet----- x.x.x.174 [Test2] Test2's Default gateway is x.x.x.170 and test2 can ping any and every valid, accessible, public IP address with no packet loss what-so-ever. If i connect directly over PPPoE from test2 (the XP box) everything works just fine... Im at my wits end, i have NO IDEA whats causing this.

  Read the article

• Trouble in Team Viewer VPN Connection

  - by Sumit Pal

  I have completed initial vpn connection setup. It has connected. I have tested with ping and it is ok. My problem is, when I want to start file transfer in VPN it asks for username & password. So what is the user name? I have tried giving Computer-Name/User-Name. I have found my Computer Name by going to Control Panel/System/ & clicking 'Computer Name' tab & username from user accounts or it is shown when I login in windows account (Please correct me if the above procedure is wrong). But what is the password? I have tried giving the account password but it always give 'The username or password is incorrect.' My Question: How to find the username & password? For Information: a) I have Team Viewer 7 installed in one Windows XP PC & one Windows 8 PC. I like to create a secure connection between these two PCs. b) The two PCs are connected in the same local network via a router. Please ask if you need additional information.

  Read the article

• Virtual Machine Network Services causes networking problems in Vista Enterprise 64 bit install

  - by Bill

  I have a Quad-core/8GB Vista Enterprise 64-bit (SP2) installation on which I installed Virtual PC 2007. I have a problem that is opposite of all that I found searching around the Internet--everybody has problems making network connections from their guest VM. When Virtual Machine Network Services is enabled in the protocol stack for my network card across a reboot, it causes access problems to the network. The amount of time to login in using a domain credentialed account is upwards of 3 minutes, then after reaching the desktop the network and sharing center shows that my connection to the domain is unauthenticated. Disabling and re-enabling the Virtual Machine Network Services (uncheck in network properties/apply/recheck/apply) fixes the problem. And as long as I have the VMNS disabled when I shutdown the restart runs smoothly. I just have to remember to enable after login and disable before shutdown. I have un-installed and re-installed Virtual PC 2007 multiple times with restarts between. The install consists of the SP1 + a KB patch for guest resolution fix. Any help would be greatly appreciated. Some additional information... At one point during my hairpulling and teethgnashing with this, I tried to ping my primary DC and observed some weird responses: (Our DC is 10.10.10.25, my dynamic IP was 10.10.10.203) Reply from 10.10.10.203, Destination host unreachable. Request timed out. Reply from 10.10.10.25: ... This is not consistently repeatable, but thought it might strike a chord with someone.

  Read the article

• Port forwarding with multiple IP's

  - by Jon

  I work at a company which uses a Fortigate 60 router, something I'm not really familiar with. Everything worked fine with it until a week ago when Comcast came in and replaced our modem. It seemed as though the process went smoothly - our connection came back up and our static IP remained the same. However, none of our port forwarding is working. What has me confused is the Comcast modem apparently has two IP addresses. The WAN2 interface for it in the Fortigate router is set to 10.1.10.10. However, all of our port forwarding settings are set to an external IP address of 10.1.10.50. Now this setup used to work fine, so something with the Comcast modem must have changed. How can I find out what? I tried setting a computer to a local IP of 10.1.10.15 so I could open up the web interface for the modem, but I can't even ping 10.1.10.10 when I do that. Any ideas? Thanks!

  Read the article

• Wireless very slow on one laptop on network, all other machines normal?

  - by th3dude19

  My new laptop (Acer Aspire Timeine 3810TZ running Windows 7 Home Premium 64bit) is acting very strange on my wireless network. Below are the issues I'm noticing... The connection frequently drops. I see the icon change from 'full bars' to 'empty bars with yellow star (meaning no connection)' occasionally. Almost every website I visit (Firefox) hangs for a long time on 'Looking up www.amazon.com' for example. After a long pause, it finally starts loading the website. Neither of these problems exist on any other machines on my network. I also have a desktop running the same OS wirelessly and it works fine. I've run several Speedtest.net tests and the speeds are great (20MBit down/4 up). Results from pingtest.net are as follows: Line quality: D Ping: 46ms Jitter: 65ms Packet Loss: 9% These results are to a server that is less than 10 miles from my residence. The results on the other machines in my house are normal. Any suggestions? This is becoming very annoying as I purchased this machine primarily for browsing.

  Read the article

• One dns server in different subnets

  - by hofmeister

  I have installed a small Linux server; the server is in a different subnet as the internet hosts. I added a route to my nat router to create a connection between both subnets. In both subnets I use an extra dhcp Server. Subnet A: 192.168.0.0/26 Subnet B: 192.168.1.0/26 Router: 192.168.0.1, Server in A: 192.168.0.62, Server in B: 192.168.1.62 internet ____ nat router ___ (Sub A)___ internet hosts | |____(Sub B)___ other hosts I could ping every host. Also the hosts which are connected to the subnet b, has internet connection. But sadly I have a problem with the dns server. I use the dnsServer from my nat router, I set the dns Server for subnet b to the ip 192.168.0.1, but every dns entries are equal with the hostname from my linux server. Example if the hostname from the server is test Test 192.168.0.62 //Server subnet a Test-2 192.168.1.62 //Server subnet b Test-2-2 192.168.1.1 //host a Test-2-2-2 192.168.1.2 //host b Any idea what went wrong? The internet dns resolution works fine.

  Read the article

• Git clone/pull across local network

  - by Tom Sarduy

  I'm trying to clone/pull a repository in another PC using Ubuntu Quantal. I have done this on Windows before but I don't know what is the problem on ubuntu. I tried these: git clone file:////pc-name/repo/repository.git git clone file:////192.168.100.18/repo/repository.git git clone file:////user:pass@pc-name/repo/repository.git git clone smb://c-pc/repo/repository.git git clone //192.168.100.18/repo/repository.git Always I got: Cloning into 'intranet'... fatal: '//c-pc/repo/repository.git' does not appear to be a git repository fatal: The remote end hung up unexpectedly or fatal: repository '//192.168.100.18/repo/repository.git' does not exist More: The other PC has username and password Is not networking issue, I can access and ping it. I just installed git doing apt-get install git (dependencies installed) I'm running git from the terminal (I'm not using git-shell) What is causing this and how to fix this? Any help would be great! UPDATE I have cloned the repo on Windows using git clone //192.168.100.18/repo/intranet.git without problems. So, the repo is accessible and exist! Maybe the problem is due user credentials?

  Read the article

• Trouble with Russian pc's on my wifi

  - by hogni89

  I have created a WiFi hotspot for the local community. The problem is, some Russian PC's (Windows XP, Windows Vista and Windows 7) can't get internet connection (We have a lot of bypassing russian fishing vessels / cargo ships). The pc's obtain a valid IP address, and some of them can even manage to send some few packages - But none of them are usable on the network. They all say "Limited internet access" or "???????????? ?????? ? ????????". The thing these PC's have in common is, that they all run a Russian installation of Windows. No one else has problems with the WiFi hotspot - Danish and English Windows, Linux and OS X all work like a charm. Can it be, that there is a difference between the danish / english windows installation, compared to the Russian installation? EDIT START They can't ping the router (One PC got one response - ONCE), they can't access any sites and Windows newer asks "Is this network public, home or work?". EDIT END PS: The hotspot is a airMAX rocket M from Ubiquiti Networks, Inc (www.ubnt.com)

  Read the article

• OpenBSD pf - implementing the equivalent of an iptables DNAT

  - by chutz

  The IP address of an internal service is going to change. We have an OpenBSD access point (ssh + autpf rules) where clients connect and open a connection to the internal IP. To give us more time to reconfigure all clients to use the new IP address, I thought we can implement the equivalent of a DNAT on the authpf box. Basically, I want to write a rule similar to this iptables rule which lets me ping both $OLD_IP and $NEW_IP. iptables -t nat -A OUTPUT -d $OLD_IP -j DNAT --to-dest $NEW_IP Our version of OpenBSD is 4.7, but we can upgrade if necessary. If this DNAT is not possible we can probably do a NAT on a firewall along the way. The closest I was able to accomplish on a test box is: pass out on em1 inet proto icmp from any to 10.68.31.99 nat-to 10.68.31.247 Unfortunately, pfctl -s state tells me that nat-to translates the source IP, while I need to translate the destination. $ sudo pfctl -s state all icmp 10.68.31.247:7263 (10.68.30.199:13437) -> 10.68.31.99:8 0:0 I also found lots of mentions about rules that start with rdr and include the -> symbol to express the translation, but it looks like this syntax has been obsoleted in 4.7 and I cannot get anything similar to work. Attempts to implement a rdr fail with a complaint that /etc/pf.conf:20: rdr-to can only be used inbound

  Read the article

• Setup my domain at Whois.com as nameservers for a Dedicated Server with Kloxo

  - by BoDiE2003

  Hello, this is my first time at ServerFault, I'm a stackoverflow user. I'm faceing the next problem and may be its me, but I can't find proper guides to set up a domain and nameservers for a dedicated box. I have a domain, at whois.com, and a Dedicated server at Reliable Hosting Services, the server has 5 IPs, I know that I need 2 of them for the nameservers. Right now, my domain at whois.com is using nsX.whois.com nameservers and it has 2 child nameservers: ns1.mydomain.com & ns2.mydomain.com pointing to those 2 IPs from my Server. Whats next? I still cannot set that domain as my main server domain since it says: To map an IP to a domain, the domain must ping to the same IP, otherwise, the domain will stop working. The domain you are trying to map this IP to, doesn't resolve back to the IP, and so it cannot be set as the default domain for the IP. Well and I'm stuck on those steps, whats next to have my nameservers working and my main domain assigned to my server? Thank you very much and happy new year!!

  Read the article

• Can't connect to Server Manager from Windows 7

  - by SAdmin317

  I have a Windows 7 Pro 64bit with SP1 desktop that has RSAT tools installed. I opened Server Manager and can't connect to the server (Server 2008 R2 core). I followed the guide to enable everything on the server, added a registry key to enable read-only on the device manager as well. On the Windows 7 PC I turned on winrm, did the quick config, and added the server IP and name as trusted hosts. I still get an error when connecting. "Connecting to the remote server failed with the following error message: The WinRM client cannot process the requests. If the authentication scheme is different from Kerberos, or if the client computer is not joined to a domain, then HTTPS transport must be used or the destination machine must be added to the TrustedHosts configuration setting...." I also added the name of the server to the windows 7 /etc/hosts file. Ping the server name translates to the IP of the server. Also opened up the firewall for "Remote Volume Management" Both machines are on the same Workgroup, using the same Administrator account, with the same password. Any help appreciated.

  Read the article

• Connect two networks

  - by Meek Barrios

  Connecting two different offices with a wireless link and linux boxes. Hardware: 2 CISCO RV42, 2 Dual Homed Linux Boxes running debian, 2 2Wire and 2 AirMax 5 Configuration is: Office A LAN A (10.1.1.0/24) -> RV42 A (WAN1 - 10.1.1.254) -> 2Wire A (Internet) LINUX A ( ETH0 (LAN) 10.1.1.253, ETH1 (LINK) (10.1.3.3) Wireless Link --- AirMax A <-> AirMax B connected as Wireless Bridge Office B LAN B (10.1.2.0/24) -> RV42 B (WAN1 - 10.1.2.254) -> 2Wire B (Internet) LINUX B ( ETH0 (LAN) 10.1.2.253 -> ETH1 (LINK) (10.1.3.4) Network configuration is: LAN A - Default Gateway 10.1.1.254 RV42 A - Static Route 10.1.3.0/24 on 10.1.1.253 Static Route 10.1.2.0/24 on 10.1.1.253 Default on 192.168.1.1 (WAN1 Internet Access) Linux A - ETH0 10.1.1.253 netmask 255.255.255.0 gw 10.1.1.254 ETH1 10.1.3.3 netmask 255.255.255.0 gw 10.1.3.1 AIRMAX A - 10.1.3.1 netmask 255.255.255.0 gw 10.1.3.1 LAN B - Default Gateway 10.1.2.254 RV42 B - Static Route 10.1.3.0/24 on 10.1.2.253 Static Route 10.1.1.0/24 on 10.1.2.253 Default on 192.168.1.1 (WAN1 Internet Access) Linux B - ETH0 10.1.2.253 netmask 255.255.255.0 gw 10.1.2.254 ETH1 10.1.3.4 netmask 255.255.255.0 gw 10.1.3.2 AIRMAX B - 10.1.3.2 netmask 255.255.255.0 gw 10.1.3.2 Both linux have ip_forward set to 1 and the following on the iptables: iptables -F iptables -X iptables -P FORWARD ACCEPT iptables -P INPUT ACCEPT iptables -P OUTPUT ACCEPT I can ping from Linux B any ip on 10.1.1.0/24 segment and on linux A any ip on 10.1.2.0/24 segment however I cannot connect to HTTP or FTP on those machines. From LAN A I cannot see any other network. I'm looking for some advice for this configuration or a better solution. Regards

  Read the article

• Linux port-based routing using iptables/ip route

  - by user42055

  I have the following setup: 192.168.0.4 192.168.0.6 192.168.0.1 +-----------+ +---------+ +----------+ |WORKSTATION|------| LINUX |------| GATEWAY | +-----------+ +---------+ +----------+ 192.168.150.10 | 192.168.150.9 +---------+ | VPN | +---------+ 192.168.150.1 WORKSTATION has a default route of 192.168.0.6 LINUX has a default route of 192.168.0.1 I am trying to use the gateway as the default route, but route port 80 traffic via the VPN. Based on what I read at http://www.linuxhorizon.ro/iproute2.html I have tried this: echo "1 VPN" >> /etc/iproute2/rt_tables sysctl net.ipv4.conf.eth0.rp_filter = 0 sysctl net.ipv4.conf.tun0.rp_filter = 0 sysctl net.ipv4.conf.all.rp_filter = 0 iptables -A PREROUTING -t mangle -i eth0 -p tcp --dport 80 -j MARK --set-mark 0x1 ip route add default via 192.168.150.9 dev tun0 table VPN ip rule add from all fwmark 0x1 table VPN When I run "tcpdump -i eth0 port 80" on LINUX, and open a webpage on WORKSTATION, I don't see the traffic go through LINUX at all. When I run a ping from WORKSTATION, I get this back from some packets: 92 bytes from 192.168.0.6: Redirect Host(New addr: 192.168.0.1) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 de91 0 0000 3f 01 4ed3 192.168.0.4 139.134.2.18 Is this why my routing is not working ? Do I need to put GATEWAY and LINUX on different subnets to prevent WORKSTATION being redirected to GATEWAY ? Do I need to use NAT at all, or can I do this with routing alone (which is what I want) ?

  Read the article

• Manual NAT on Checkpoint (Redirect all http requests to a local web server)

  - by kulakli

  Hi, We have a proxy server in internal network and I want to redirect all internet http requests to a web server in local network. It'll be like a Network Billboard that say "No direct connection is available. Set up your proxy etc." For example: A user starts the computer Opens the browser Trys to open www.google.com Should see web server output on local network Trys another web site on internet Should see web server output on local network Sets up proxy Trys to connect to a web site Web site should be loaded I have added a simple manual NAT rule to address translation in Checkpoint firewall but it simply does not work. Here is my address translation rule Source Destination Service T.Source T.Destination T.Service MY_PC A_GOOGLE_IP ALL ORIGINAL INT_WEB_SRV ORIGINAL Then when I ping A_GOOGLE_IP, replies come from INT_WEB_SRV, as I expected. However, when I try to connect A_GOOGLE_IP from browser (http://A_GOOGLE_IP), No replies come from SYN_SENT and falls into timeout. When I look at the firewall log of INT_WEB_SRV, I can see the incoming connection requests from MY_PC is accepted and NO denies. By the way, there is no problem to see INT_WEB_SRV (http://INT_WEB_SRV) from browser. My understanding is, my nat rule at checkpoint NGX R60 does not include return packets. I definitely need some help. Regards, Burak

  Read the article

• very slow internet with Linksys WRT54GL only in wireless mode (wired is OK)

  - by gojira

  I bought a new Cisco Linksys WRT54GL router to connect my laptop (running Windows 7) to the internet. I installed Tomato 1.28 firmware on the router. When I connect the laptop to the router via ethernet cable, everything is fine and I get extremely fast up- and download speeds. When I connect wirelesssly however, websites load extremely slow - it takes dozens of seconds to load a website! <-- This is my question, how can I fix the wireless speed issue? Gmail for example is unusable this way. I tried speedtest.net, but this always fails in the upload part of the test so I can't even test the bandwidth (could the fact that it fails in the upload part, not the download part, be an indication what the problem is?!). I have isolated the problem a bit, I am convinced it has to do either with the router itself, the router settings, or the settings of the wireless connection in Win 7. Because previously, I was using another router by Buffalo and I had no problems whatsoever. I have tried to reproduce the settings from the Bufallo router as closely as possible on the Linksys router (same channel, same encryption etc). The download speed problem only occurs with the Linksys router, and only in wireless mode! When I exchange the Linksys router with the Buffalo router I have here for testing, the wireless speed is up to normal again. Also, before I had installed the Tomato firmware I had exactly the same problem, so it has nothing to do with the firmware itself. Notes & things I already tried: Changing the channel: does not seem to affect anything, I am also on the same channel (10) which I was previously on when I had a Buffalo router. QoS is off. Ping to the router itself is OK, ~ 1 ms. Some current settings of the linksys router: WAN / Internet Type: DHCP Wirelesss Mode: Access Point B/G Mode: Mixed Broadcast: check Channel: 10 - 2.457 GHz Security: WPA2 Personal Encryption: AES

  Read the article

• Connection failed between Windows Servers

  - by Kerby82

  I'm setting up an infrastructure based on Windows Server 2012. The firewall is turned off and I can't access the Domain controller to check for the group policy. I'm experiencing some connection problem between servers. All the servers are running a site on the TCP Port 80 and I check with netstat that the web server is binding on every Ip of the servers. If i try to telnet from the server itself on the port 80 it works (using DNS name) if I try same telnet from another machine I get connection failed. The DNS works, the ping is successfull, the servers are on the same subnet, the firewall is turned off (even though windows advanced firewall says that some settings can be managed by the System Administrator, i guess group policy). I don't know how to troubleshoot further. Do you have any idea? Is that possible that the FW looks turned off but there are some group policy blocking the connections? (I also check group policy-Administrative Template-Network Connections- Windows FW everything is not configured) I need some hint on how to keep troubleshooting such a problem.

  Read the article

• script to list user's mapped drive not giving results or error

  - by user223631

  We are in the process of migrating two file servers to a new server. We have mapped drives via user group in group policy. Many users have manually mapped drives and we need to find these mappings. I have created a PowerShell script to run that remotely get the drive mappings. It works on most computers but there are many that are not returning results and I am not getting any error messages. Each workstation on the list creates a text file and the ones that are not returning results have no text in the files. I can ping these machines. If the machine is not turned on, it does come up error message that the RPC server is not available. My domain user account is in a group that is in the local admin account. I have no idea why some are not working. Here is the script. # Load list into variable, which will become an array of strings If( !(Test-Path C:\Scripts)) { New-Item C:\Scripts -ItemType directory } If( !(Test-Path C:\Scripts\Computers)) { New-Item C:\Scripts\Computers -ItemType directory } If( !(Test-Path C:\Scripts\Workstations.txt)) { "No Workstations found. Please enter a list of Workstations under Workstation.txt"; Return} If( !(Test-Path C:\Scripts\KnownMaps.txt)) { "No Mapping to check against. Please enter a list of Known Mappings under KnownMaps.txt"; Return} $computerlist = Get-Content C:\Scripts\Workstations.txt # Loop through each item in the array (each computer in the list of computers we loaded into the variable) ForEach ($computer in $computerlist) { $diskObject = Get-WmiObject Win32_MappedLogicalDisk -computerName $computer | Select Name,ProviderName | Out-File C:\Tester\Computers\$computer.txt -width 200 } Select-String -Path C:\Tester\Computers\*.txt -Pattern cmsfiles | Out-File C:\Tester\Drivemaps-all.txt $strings = Get-Content C:\Tester\KnownMaps.txt Select-String -Path C:\Tester\Drivemaps-all.txt -Pattern $strings -notmatch -simplematch | Out-File C:\Tester\Drivemaps-nonmatch.txt -Width 200 Select-String -Path C:\Tester\Drivemaps-all.txt -Pattern $strings -simplematch | Out-File C:\Tester\Drivemaps-match.txt -Width 200

  Read the article

• My home router randomly disconnects me and I'm unable to reconnect to it

  - by Roy Tang

  It's happened a few times, I'm not sure how to diagnose/debug, so any advise would be appreciated. Symptons: sometimes the router will randomly disconnect; the connection icon on my desktop (wired to the router) gets that yellow "!" symbol that tells me my connection just went down. At this point I'm unable to ping the router. afterwards I try to reset the router by removing then reconnecting the power jack on the router side (this is the fastest way as I can't reset the power strip it's connected to without rebooting my desktop. the router has a reset thingy, but it's one of those things where i have to find a pin to stick into the hole, and when I get disconnected I usually need to get reconnected immediately so I just pull and put back the power jack), but even after that the connection has the same state. after the router reboots, if I try to connect to it using a wifi device like my ipad, the ipad prompts me for the wifi password even though it had already "remembered" all the settings for this router forever after i finally decide to reboot the power strip, and my desktop and the router boot up again, the connection returns to its normal state somewhat and i'm able to connect to it as normal using the desktop and wifi devices. What do I need to check the next time this happens so I can figure out the problem? Is it possibly because we've been using the power jack on the router as an easier way to reboot it? Should I be shopping around for a new router? If it helps, the router is a DLink DIR-300

  Read the article

< Previous Page | 94 95 96 97 98 99 100 101 102 103 104 105  | Next Page >