After reboot my SATA 1TB WD1000FYPS (previously is was "Drive error") is marked 0 mb in 3ware web gui.

Complete message:

Available Drives (Controller ID 0)
Port 1  WDC WD1000FYPS-01ZKB0   0.00 MB NOT SUPPORTED   [Remove Drive]

SMART gives me only Device Model and ATA protocol version 1 (not 7-8 as it must be for SATA)

What does it mean?

Just before reboot, when is was marked only with "Device Error", smart was:

Device Model:     WDC WD1000FYPS-01ZKB0
Serial Number:    WD-WCASJ1130***
Firmware Version: 02.01B01
User Capacity:    1,000,204,886,016 bytes
Device is:        Not in smartctl database [for details use: -P showall]
ATA Version is:   8
ATA Standard is:  Exact ATA specification draft version not indicated
Local Time is:    Sun Mar  7 18:47:35 2010 MSK
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

SMART overall-health self-assessment test result: PASSED

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000f   200   200   051    Pre-fail  Always       -       0
  3 Spin_Up_Time            0x0003   188   186   021    Pre-fail  Always       -       7591
  4 Start_Stop_Count        0x0032   100   100   000    Old_age   Always       -       229
  5 Reallocated_Sector_Ct   0x0033   199   199   140    Pre-fail  Always       -       3
  7 Seek_Error_Rate         0x000e   193   193   000    Old_age   Always       -       125
  9 Power_On_Hours          0x0032   078   078   000    Old_age   Always       -       16615
 10 Spin_Retry_Count        0x0012   100   100   000    Old_age   Always       -       0
 11 Calibration_Retry_Count 0x0012   100   253   000    Old_age   Always       -       0
 12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       -       77
192 Power-Off_Retract_Count 0x0032   198   198   000    Old_age   Always       -       1564
193 Load_Cycle_Count        0x0032   146   146   000    Old_age   Always       -       164824
194 Temperature_Celsius     0x0022   117   100   000    Old_age   Always       -       35
196 Reallocated_Event_Count 0x0032   199   199   000    Old_age   Always       -       1
197 Current_Pending_Sector  0x0012   200   200   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0010   200   200   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x003e   200   200   000    Old_age   Always       -       0
200 Multi_Zone_Error_Rate   0x0008   200   200   000    Old_age   Offline      -       0

What can be wrong with he? Can it be restored?

PS

new smart is

=== START OF INFORMATION SECTION ===
Device Model:     WDC WD1000FYPS-01ZKB0
Serial Number:    [No Information Found]
Firmware Version: [No Information Found]
Device is:        Not in smartctl database [for details use: -P showall]
ATA Version is:   1
ATA Standard is:  Exact ATA specification draft version not indicated
Local Time is:    Mon Mar  8 00:29:44 2010 MSK
SMART is only available in ATA Version 3 Revision 3 or greater.
We will try to proceed in spite of this.
SMART support is: Ambiguous - ATA IDENTIFY DEVICE words 82-83 don't show if SMART supported.
                  Checking for SMART support by trying SMART ENABLE command.
Command failed, ata.status=(0x00), ata.command=(0x51), ata.flags=(0x01)
Error SMART Enable failed: Input/output error
                  SMART ENABLE failed - this establishes that this device lacks SMART functionality.
A mandatory SMART command failed: exiting. To continue, add one or more '-T permissive' options.

PPS There was a rapid grow of " 192 Power-Off_Retract_Count " before dying. The hard was used in raid, with several hards from the same fabric packaging box (close id's). The hard drives were placed identically. Rapid means almost linear grow from 300 to 1700 in 6-7 hours. Maximal temperature was 41C. (thanks to munin's smart monitoring)