3 Servers, 2 Work Fine, One Has Network Issues

Posted by ScaleOvenStove on Server Fault See other posts from Server Fault or by ScaleOvenStove
Published on 2010-03-13T17:43:44Z Indexed on 2010/03/13 17:45 UTC
Read the original article Hit count: 356

Filed under:

networking

|

nic

|

teaming

|

windows-server-2008

i have 3 servers, all relatively the same hardware/config, etc. I run some data pulls on all 3, and on 2 of them, they have 1 nic, and they work fine. On the other , there are 2 nics, and unless they are both plugged in or teamed, the processes time out.

Any ideas on why this would be? It doesn't make sense to me, as the other two work fine with 1 nic and don't time out when running the same processes.

© Server Fault or respective owner

Related posts about networking

Networking stopped working on Ubuntu

as seen on Super User - Search for 'Super User'
I installed Ubuntu 10.04 through the Wubi installer (Funny, I installed it today and thought I would have gotten 10.10). I had a network connection and everything was working fine. I rebooted my coumputer a couple of times and then suddenly, I could not connect to the network and when I click the… >>> More
Troubles with start up defenition of networking service in Ubuntu

as seen on Super User - Search for 'Super User'
I use Ubuntu 12.04.1. I put attention that networking script starting in runlevel 0: user@comp:/etc/rc0.d$ chkconfig -l networking networking 0:on 1:off 2:off 3:off 4:off 5:off 6:off When I try to move it working to appropriate run levels I get error: user@comp:/etc/rc0… >>> More
Installing the Elgg Social Networking CMS

as seen on Internet.com - Search for 'Internet.com'
One Open Source CMS that stands out above the rest for small businesses and personal networks is the Elgg open source "social engine," which can be used to create social applications. Scott Clark shows you how to install and get started with this social networking CMS. >>> More
OAuth: Token-Based Authorization for the Social Networking Age

as seen on Internet.com - Search for 'Internet.com'
The OAuth token-based authorization system allows users to grant third-party access to their resources without sharing their usernames and passwords. It's perfect for the age of data scattered across many social networking sites. >>> More
OAuth: Token-Based Authorization for the Social Networking Age

as seen on Internet.com - Search for 'Internet.com'
The OAuth token-based authorization system allows users to grant third-party access to their resources without sharing their usernames and passwords. It's perfect for the age of data scattered across many social networking sites. >>> More

Related posts about nic

My laptop can not access internet after setup bridge with wired NIC and wireless NIC

as seen on Ask Ubuntu - Search for 'Ask Ubuntu'
I setup a bridge using wired NIC and wireless NIC in order to make wireless NIC as a Wi-Fi AP to share wired internet access, after setup successfully, the Wi-Fi AP works as my expectation, but my laptop can not access internet, please give me a hand. Thanks. My hostapd.conf $ cat hostapd.conf interface=wlan0 bridge=br0 driver=nl80211 ssid=myAP hw_mode=g channel=11 dtim_period=1 rts_threshold=2347 fragm_threshold=2346 macaddr_acl=0 auth_algs=3 ieee80211n=0 wpa=3 wpa_passphrase=PassWord wpa_key_mgmt=WPA-PSK wpa_pairwise=TKIP rsn_pairwise=CCMP Setup… >>> More
forwarding packets from wireless nic wlan0 to another Wireless nic wlan1

as seen on Server Fault - Search for 'Server Fault'
I have two wireless interfaces wlan0, wlan1 I want wlan0 to be connected to the internet via a wireless router and I want wlan1 to be in AP mode acting as a router to give internet access to whoever connectes to it. So basically all packets coming through wlan1 should be forwarded to wlan0 = Router… >>> More
Windows Server: specifying the default IP address when NIC has multiple addresses

as seen on Server Fault - Search for 'Server Fault'
I have a Windows Server which has ~10 IP addresses statically bound. The problem is I don't know how to specify the default IP address. Sometimes when I assign a new address to the NIC, the default IP address changes with the last IP entered in the advanced IP configuration on the NIC. This has the… >>> More
WD MBWE II (White Strip Light) 2TB - unable to access data

as seen on Super User - Search for 'Super User'
I have a WD MBWE II (White Strip Light) 2TB - (WD20000H2NC-00) Was working fine until a few days ago. I guess there was a power failure and after that I am unable to access the 'Public' or the 'Download' folder anymore. I have been searching for answers everywhere but came up empty handed. Web… >>> More
Set up two IP addresses with one gateway?

as seen on Ask Ubuntu - Search for 'Ask Ubuntu'
I would like to ask if it is possible to set up two static IPs from same subnet through one gateway? and How if it is? What I am interested in is described here Routing for multiple uplinks/providers, but in my case I have two IP addresses from one provider, both are on same subnet and off course… >>> More