How do I convert a Windows 7 Ultimate install to Raid 0?

Posted by user16037 on Super User See other posts from Super User or by user16037
Published on 2009-10-30T04:53:00Z Indexed on 2010/03/24 3:03 UTC
Read the original article Hit count: 275

Filed under:

software-raid

|

windows-7

|

raid-0

I'm trying to convert my system to RAID 0 and so far I found contrasting opinions on the process. Somebody says Windows 7 can't boot from virtual volumes, somebody says it can.

My ideal setup would be two 500gb HD striped in RAID 0 with the OS and software installed on them.

Any thoughts?

© Super User or respective owner

Related posts about software-raid

Linux Software RAID-1 in production environment

as seen on Server Fault - Search for 'Server Fault'
Is it recommended to use software RAID-1 in a production environment? Due to budget constraints, I cannot get a hardware RAID controller for a new server. While I'm aware of a slight performance decrease, is it really that much of a difference? >>> More
How to install Windows 7 onto software RAID-0

as seen on Super User - Search for 'Super User'
I recently got a new laptop (Asus G73JH-A2) which has two identical hard drives in it. Unfortunately the motherboard does not have a RAID controller. What I would like to do is run the drives in a RAID-0 configuration to improve performance (plus get the extra capacity on one partition). I would… >>> More
Problems migrating software RAID 5 to new server (linux)

as seen on Server Fault - Search for 'Server Fault'
I have a CentOS setup with sw RAID5 that holds my data. Well, the server died, so I bought another box to migrate my drives to. Only thing is, I cannot get the RAID array rebuilt (not even sure it needs rebuilding, might just need the /dev/md0 mapping created... but I don't even know how to determine… >>> More
Linux boot on a raid1 software raid ?

as seen on Server Fault - Search for 'Server Fault'
Hello I am trying to convert my single disk boot to a raid1 boot So far here is what i have: I sucessfully create the raid 1 as degraded with the new drive alone, I copied all the data on it I can mount that raid 1, see its files etc I already have a raid5 that is working on the same box (although… >>> More
Mac OS X Server 10.6 - Apple's software mirrored RAID worth it?

as seen on Server Fault - Search for 'Server Fault'
Hi, I am installing an Intel Xserve (Quad core Xeon) with Snow Leopard Server (10.6) on two 80Gb 7200rpm SATA HDs. I created a mirrored RAID set using Disk Utility with those two drives, all went fine. I was then asking myself if this is really a good idea. I know that an hardware RAID system would… >>> More

Related posts about windows-7

Server 2012 DFS New Member Issue

as seen on Server Fault - Search for 'Server Fault'
I am trying to add a new member to our DFS topology. We have 3 DCs (VMs - VMware) running Windows server 2012, two servers are located in or Primary site and the third at our DR site. Currently the two servers at our primary site are currently replicating DFS (full mesh) and are working fine. I have… >>> More
error in IIS7 but not on IIS6

as seen on Server Fault - Search for 'Server Fault'
I have a website that is we are now deploying to windows 2008 servers that has worked in the past on IIS6 without a problem. It is using .net 2 framework. Most of the website works. Just when we create a screen report over a certain size on the server we get this error. Event code: 3005 Event… >>> More
error in IIS7 but not on IIS6

as seen on Server Fault - Search for 'Server Fault'
I have a website that is we are now deploying to windows 2008 servers that has worked in the past on IIS6 without a problem. It is using .net 2 framework. Most of the website works. Just when we create a screen report over a certain size on the server we get this error. Event code: 3005 Event… >>> More
Microsoft Management Console stops working when I add snap-in to it

as seen on Super User - Search for 'Super User'
I have Windows 7 Ultimate OS. I'm opening mmc.exe as administrator and trying add Certificates or any other snap-in, then while loading that snap-in MMC breaks and displays following message and after that it closes automatically once I click on close button on that message. What could be the problem… >>> More
Handling keyboard and mouse input (Win API)

as seen on Game Development - Search for 'Game Development'
There is a number of ways to catch mouse or keyboard under Windows. So I tried some of them, but every of them has some advantages and drawbacks. I want to ask you: Which method do use? I've tried these: WM_KEYDOWN/WM_KEYUP - Main disadvantage is that, I can't distinguish between left and right-handed… >>> More