No clock with FTDIchip FT2232 MPSSE mode

Posted by Simi on Stack Overflow See other posts from Stack Overflow or by Simi
Published on 2010-03-24T15:52:39Z Indexed on 2010/03/24 16:33 UTC
Read the original article Hit count: 207

Filed under:

labview

|

device

|

extern

|

clock

Hello,

I'm trying to write/read to an extern device connected to a FTDIchip FT2232 MPSSE mode using SPI. I'm using the SPI function given by FTDI for Labview. I'm doing this:

Open_Device - Init_Device - Write/Read - Close_Device

The problem is that I don't have a clock signal on the scope when I try to read/write.

Do you have a solution?

Thanks

© Stack Overflow or respective owner

Related posts about labview

What is C's analogy to LabVIEW's Event Structure?

as seen on Stack Overflow - Search for 'Stack Overflow'
One programming construct I use quite a bit in LabVIEW is the Event Structure. This gives me the benefit of not having to needlessly waste CPU cycles via polling but only perform actions when an event I'm interested in is generated. As an experienced LabVIEW programmer with a decent understanding… >>> More
Interpolation and Morphing of an image in labview and/or openCV

as seen on Stack Overflow - Search for 'Stack Overflow'
I am working on an image manipulation problem. I have an overhead projector that projects onto a screen, and I have a camera that takes pictures of that. I can establish a 1:1 correspondence between a subset of projector coordinates and a subset of camera pixels by projecting dots on the screen… >>> More
Labview String output

as seen on Stack Overflow - Search for 'Stack Overflow'
How do I send a string output from a DAQ Board (NI- USB 6259) using labview? I want to send commands such as " CELL 0" or "READ" to a potentiostat device using labview. Thanks >>> More
LabView Control (.ctl) to VB.NET Structure

as seen on Stack Overflow - Search for 'Stack Overflow'
I created a control in LabView. My LabView code writes data of that type to a binary file. I want to read this data into a VB Structure. Can I do this programmatically, or do I need to manually create a corresponding structure? >>> More
In LabVIEW, get callees without loading a VI

as seen on Stack Overflow - Search for 'Stack Overflow'
Here's an obscure Friday Morning question: Is it possible in LabVIEW to get the callees of a VI without loading the entire VI into memory? For instance, by reading static information from the binary? Thanks >>> More

Related posts about device

LVM / Device Mapper maps wrong device

as seen on Server Fault - Search for 'Server Fault'
Hi, I run a LVM setup on a raid1 created by mdadm. md2 is based on sda6 (major:minor 8:6) and sdb6 (8:22). md2 is partition 9:2. The VG on top of md2 has 4 LVs, var, home, usr, tmp. First the problem: While booting it seems as if the device mapper takes the wrong partition for the mapping! Immediately… >>> More
External HDD USB 3.0 failure

as seen on Ask Ubuntu - Search for 'Ask Ubuntu'
[ 2560.376113] usb 9-1: new high-speed USB device number 2 using xhci_hcd [ 2560.376186] usb 9-1: Device not responding to set address. [ 2560.580136] usb 9-1: Device not responding to set address. [ 2560.784104] usb 9-1: device not accepting address 2, error -71 [ 2560.840127] hub 9-0:1.0: unable… >>> More
Write-error on swap-device, Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK

as seen on Server Fault - Search for 'Server Fault'
My root server at 1&1 was unresponsive on HTTP and SSH, so I logged into the serial console . It flooded my connection with endless error messages like quoted below. I initiated a reboot and now everything seems to work properly. After googling, I installed smartctl and ran a short self test… >>> More
Pulseaudio is no longer working in Debian Squeeze: 'Failed to open module "module-combine-sink": file not found'

as seen on Super User - Search for 'Super User'
I'm having a problem with pulseaudio. My machine crashed, and when I rebooted and ran pavucontrol, I got a "Connection Failed: Connection refused" dialog. When I run pulseaudio --log-level=info --log-target=stderr from the command line, I get the following output: [...] I: alsa-util.c: Error opening… >>> More
USB Drive Not recognized

as seen on Super User - Search for 'Super User'
My Friend's Pen Drive, which was working well very well just few days ago, is not being recognized after getting used by a virus affected machine. Its not on fdisk -l or lsusb However in dmesg I can see the following: [ 977.300013] usb 5-2: new full speed USB device using uhci_hcd and address 2 [… >>> More