-
as seen on Server Fault
- Search for 'Server Fault'
For some reason VMWare ESXi has decided that one of my VMs is on a completely different path to the path it is actually on.
So my VM is on /vmfs/volumes/long-guid-here/my-vm-name but when I try to open it I get the message "File < unspecified filename was not found." Which is not really surprising…
>>> More
-
as seen on Server Fault
- Search for 'Server Fault'
Hello everyone! I am using VMWare ESXi 3.5 on my server, and I want to be able to remotely boot the server up. In the bios settings of the computer, I enabled Wake on Lan. I know usually with Windows XP and other Windows Operating Systems, you have to also enable wake on lan in the network card settings…
>>> More
-
as seen on Server Fault
- Search for 'Server Fault'
Hi,
I need some advice about using blu-ray writer for archiving data on vmware ESXi 4. At office we have IBM System x3400 Tower server with ESXi 4 hipervisor and OpenSuse and CentOS GNU/Linux system as guests. Will blu-ray writer work in this setup, and if it will is there any particular model you…
>>> More
-
as seen on Server Fault
- Search for 'Server Fault'
Yes, I know running a virtual machine inside of a virtual machine is a bad idea. Yes, I know it will be very slow. However, our production system required VMs in VMWare server and I do not want to setup a real server for each of our developers for testing. I would like to be able to setup all of…
>>> More
-
as seen on Server Fault
- Search for 'Server Fault'
I'm almost embarrassed to ask this, but I'm stuck. I installed VMWare ESXi on a Mac Pro. It's working great! The problem is that you press F12 to eject the disk, and F12 is what you use to shutdown ESX. I can power down, open the case, pull out the CD drive and use a paper clip to force the drawer…
>>> More
-
as seen on Server Fault
- Search for 'Server Fault'
For the life of me I cannot figure out how to remove an iSCSI target (Dell Equallogic SAN) from a Windows Server 2003 box. The volume shows up in Windows as drive letter Y:\
Using the iSCSI initiator, I can remove the Target Portal, but cannot remove the Target itself.
Can someone give me some…
>>> More
-
as seen on Server Fault
- Search for 'Server Fault'
We have an IBM P505 AIX box, with two internal disks and a defined iSCSI volume.
The iSCSI volume is defined in it's own volume group, and is connected to an IBM iSCSI DS3300 disk array via the secondary onboard ethernet port (ie, we're not using a dedicated HBA, we're using the second onboard ethernet…
>>> More
-
as seen on Server Fault
- Search for 'Server Fault'
I had asked the similar question before. This time I want to use subnet for two iSCSI Targets, hence I start a new question.
I have an old Promise VTrak M500i SAN Server. It comes with 2 iSCSI ports. I want to connect to two LUNs on the SAN server through two separate Targets from CentOS 5.7 64bits…
>>> More
-
as seen on Server Fault
- Search for 'Server Fault'
Hi!
I have problem with using multiply iSCSI targets with single ESXi host (in my case they are two FreeNAS hosts, but I suspect that this problem will occur with any two iSCSI box of that same type/model). If I configure two FreeNAS hosts as iSCSI targets (say iSCSI A and iSCSI B), then I can use…
>>> More
-
as seen on Server Fault
- Search for 'Server Fault'
I am running a dell poweredge 1950 with 4 nic cards. 1 is bonded to SAN #1 on 192.168.90.xx. The second SAN is on a separate network - 192.168.7.xx The network adapter can view the ip range of the san and the NIC can be pinged from 192.168.7.xx range. vswitch1 and vswitch2 are configured identically…
>>> More
