I am writing the firmware for an embedded device in C using the Silicon Labs IDE and the SDCC compiler. The device architecture is based on the 8051 family. The function in question is shown below. The function is used to set the ports on my MCU to drive a stepper motor. It gets called in by an interrupt handler. The big switch statement just sets the ports to the proper value for the next motor step. The bottom part of the function looks at an input from a hall effect sensor and a number of steps moved in order to detect if the motor has stalled. The problem is, for some reason the second IF statement that looks like this if (StallDetector > (GapSize + 20)) { HandleStallEvent(); } always seems to get optimized out. If I try to put a breakpoint at the HandleStallEvent() call the IDE gives me a message saying "No Address Correlation to this line number". I am not really good enough at reading assembly to tell what it is doing but I have pasted a snippet from the asm output below. Any help would be much appreciated.

void OperateStepper(void)
{
    //static bit LastHomeMagState = HomeSensor;
    static bit LastPosMagState = PosSensor;
    if(PulseMotor)
    {
        if(MoveDirection == 1) // Go clockwise
        {
            switch(STEPPER_POSITION) 
            {
                case 'A': 
                     STEPPER_POSITION = 'B';
                     P1 = 0xFD;
                     break;
                case 'B':
                     STEPPER_POSITION = 'C';
                     P1 = 0xFF;
                     break;
                case 'C':
                     STEPPER_POSITION = 'D';
                     P1 = 0xFE;
                     break;
                case 'D':
                     STEPPER_POSITION = 'A';
                     P1 = 0xFC;
                     break; 
                default:
                     STEPPER_POSITION = 'A';
                     P1 = 0xFC;
            }   //end switch
        }
        else                // Go CounterClockwise
        {
            switch(STEPPER_POSITION) 
            {
                case 'A': 
                     STEPPER_POSITION = 'D';
                     P1 = 0xFE;
                     break;
                case 'B': 
                     STEPPER_POSITION = 'A';
                     P1 = 0xFC;
                     break;
                case 'C': 
                     STEPPER_POSITION = 'B';
                     P1 = 0xFD;
                     break;
                case 'D': 
                     STEPPER_POSITION = 'C';
                     P1 = 0xFF;
                     break; 
                default: 
                     STEPPER_POSITION = 'A';
                     P1 = 0xFE;
            }   //end switch
        }   //end else

        MotorSteps++;
        StallDetector++;

        if(PosSensor != LastPosMagState)
        {
            StallDetector = 0;

            LastPosMagState = PosSensor;
        }
        else
        {
            if (PosSensor == ON) 
            {
                if (StallDetector > (MagnetSize + 20))
                {
                    HandleStallEvent();
                }
            }
            else if (PosSensor == OFF) 
            {
                if (StallDetector > (GapSize + 20))
                {
                    HandleStallEvent();
                }
            }
        }

    }   //end if PulseMotor
}

... and the asm output for the the bottom part of this function...

;   C:\SiLabs\Optec Programs\HSFW_HID_SDCC_2\MotionControl.c:653: if(PosSensor != LastPosMagState)
    mov c,_P1_4
    jb  _OperateStepper_LastPosMagState_1_1,00158$
    cpl c
00158$:
    jc  00126$
    C$MotionControl.c$655$3$7 ==.
;   C:\SiLabs\Optec Programs\HSFW_HID_SDCC_2\MotionControl.c:655: StallDetector = 0;
    clr a
    mov _StallDetector,a
    mov (_StallDetector + 1),a
    C$MotionControl.c$657$3$7 ==.
;   C:\SiLabs\Optec Programs\HSFW_HID_SDCC_2\MotionControl.c:657: LastPosMagState = PosSensor;
    mov c,_P1_4
    mov _OperateStepper_LastPosMagState_1_1,c
    ret
00126$:
    C$MotionControl.c$661$2$8 ==.
;   C:\SiLabs\Optec Programs\HSFW_HID_SDCC_2\MotionControl.c:661: if (PosSensor == ON) 
    jb  _P1_4,00123$
    C$MotionControl.c$663$4$9 ==.
;   C:\SiLabs\Optec Programs\HSFW_HID_SDCC_2\MotionControl.c:663: if (StallDetector > (MagnetSize + 20))
    mov a,_MagnetSize
    mov r2,a
    rlc a
    subb    a,acc
    mov r3,a
    mov a,#0x14
    add a,r2
    mov r2,a
    clr a
    addc    a,r3
    mov r3,a
    clr c
    mov a,r2
    subb    a,_StallDetector
    mov a,r3
    subb    a,(_StallDetector + 1)
    jnc 00130$
    C$MotionControl.c$665$5$10 ==.
;   C:\SiLabs\Optec Programs\HSFW_HID_SDCC_2\MotionControl.c:665: HandleStallEvent();
    ljmp    _HandleStallEvent
00123$:
    C$MotionControl.c$668$2$8 ==.
;   C:\SiLabs\Optec Programs\HSFW_HID_SDCC_2\MotionControl.c:668: else if (PosSensor == OFF) 
    jnb _P1_4,00130$
    C$MotionControl.c$670$4$11 ==.
;   C:\SiLabs\Optec Programs\HSFW_HID_SDCC_2\MotionControl.c:670: if (StallDetector > (GapSize + 20))
    mov a,#0x14
    add a,_GapSize
    mov r2,a
    clr a
    addc    a,(_GapSize + 1)
    mov r3,a
    clr c
    mov a,r2
    subb    a,_StallDetector
    mov a,r3
    subb    a,(_StallDetector + 1)
    jnc 00130$
    C$MotionControl.c$672$5$12 ==.
;   C:\SiLabs\Optec Programs\HSFW_HID_SDCC_2\MotionControl.c:672: HandleStallEvent();
    C$MotionControl.c$678$2$1 ==.
    XG$OperateStepper$0$0 ==.
    ljmp    _HandleStallEvent
00130$:
    ret

It looks to me like the compiler is NOT optimizing out this second if statement from the looks of the asm but if that is the case why does the IDE not allow me so set a breakpoint there? Maybe it's just a dumb IDE!