Dual NIC internet access

Posted by JavaRocky on Server Fault See other posts from Server Fault or by JavaRocky
Published on 2010-05-01T03:12:14Z Indexed on 2010/05/01 3:18 UTC
Read the original article Hit count: 569

Filed under:

nic

|

Windows

|

networking

|

wireless-network

|

routing

Q1. If a computer had two NICs, lets say windows, on which interface would HTTP traffic (or any for that matter) go out on.

Not sure how the routes table would look like.

Q2. If one of the NICs link becomes unresponsive, would traffic be automatically routed to the other NIC?

Thanks.

© Server Fault or respective owner

Related posts about nic

My laptop can not access internet after setup bridge with wired NIC and wireless NIC

as seen on Ask Ubuntu - Search for 'Ask Ubuntu'
I setup a bridge using wired NIC and wireless NIC in order to make wireless NIC as a Wi-Fi AP to share wired internet access, after setup successfully, the Wi-Fi AP works as my expectation, but my laptop can not access internet, please give me a hand. Thanks. My hostapd.conf $ cat hostapd.conf interface=wlan0 bridge=br0 driver=nl80211 ssid=myAP hw_mode=g channel=11 dtim_period=1 rts_threshold=2347 fragm_threshold=2346 macaddr_acl=0 auth_algs=3 ieee80211n=0 wpa=3 wpa_passphrase=PassWord wpa_key_mgmt=WPA-PSK wpa_pairwise=TKIP rsn_pairwise=CCMP Setup… >>> More
forwarding packets from wireless nic wlan0 to another Wireless nic wlan1

as seen on Server Fault - Search for 'Server Fault'
I have two wireless interfaces wlan0, wlan1 I want wlan0 to be connected to the internet via a wireless router and I want wlan1 to be in AP mode acting as a router to give internet access to whoever connectes to it. So basically all packets coming through wlan1 should be forwarded to wlan0 = Router… >>> More
Windows Server: specifying the default IP address when NIC has multiple addresses

as seen on Server Fault - Search for 'Server Fault'
I have a Windows Server which has ~10 IP addresses statically bound. The problem is I don't know how to specify the default IP address. Sometimes when I assign a new address to the NIC, the default IP address changes with the last IP entered in the advanced IP configuration on the NIC. This has the… >>> More
WD MBWE II (White Strip Light) 2TB - unable to access data

as seen on Super User - Search for 'Super User'
I have a WD MBWE II (White Strip Light) 2TB - (WD20000H2NC-00) Was working fine until a few days ago. I guess there was a power failure and after that I am unable to access the 'Public' or the 'Download' folder anymore. I have been searching for answers everywhere but came up empty handed. Web… >>> More
Set up two IP addresses with one gateway?

as seen on Ask Ubuntu - Search for 'Ask Ubuntu'
I would like to ask if it is possible to set up two static IPs from same subnet through one gateway? and How if it is? What I am interested in is described here Routing for multiple uplinks/providers, but in my case I have two IP addresses from one provider, both are on same subnet and off course… >>> More

Related posts about Windows

Server 2012 DFS New Member Issue

as seen on Server Fault - Search for 'Server Fault'
I am trying to add a new member to our DFS topology. We have 3 DCs (VMs - VMware) running Windows server 2012, two servers are located in or Primary site and the third at our DR site. Currently the two servers at our primary site are currently replicating DFS (full mesh) and are working fine. I have… >>> More
error in IIS7 but not on IIS6

as seen on Server Fault - Search for 'Server Fault'
I have a website that is we are now deploying to windows 2008 servers that has worked in the past on IIS6 without a problem. It is using .net 2 framework. Most of the website works. Just when we create a screen report over a certain size on the server we get this error. Event code: 3005 Event… >>> More
error in IIS7 but not on IIS6

as seen on Server Fault - Search for 'Server Fault'
I have a website that is we are now deploying to windows 2008 servers that has worked in the past on IIS6 without a problem. It is using .net 2 framework. Most of the website works. Just when we create a screen report over a certain size on the server we get this error. Event code: 3005 Event… >>> More
Microsoft Management Console stops working when I add snap-in to it

as seen on Super User - Search for 'Super User'
I have Windows 7 Ultimate OS. I'm opening mmc.exe as administrator and trying add Certificates or any other snap-in, then while loading that snap-in MMC breaks and displays following message and after that it closes automatically once I click on close button on that message. What could be the problem… >>> More
Handling keyboard and mouse input (Win API)

as seen on Game Development - Search for 'Game Development'
There is a number of ways to catch mouse or keyboard under Windows. So I tried some of them, but every of them has some advantages and drawbacks. I want to ask you: Which method do use? I've tried these: WM_KEYDOWN/WM_KEYUP - Main disadvantage is that, I can't distinguish between left and right-handed… >>> More