Ok, so, I have one of those fancy schmancy devices, which is given to me by a frustrated friend of mine.

Device is a Prestigio Leather 8GB, which identifies itself to Linux host as:

Bus 001 Device 006: ID 1307:0165 Transcend Information, Inc. 2GB/4GB Flash Drive

Kernel messages as USB device is plugged in:

kernel: [ 2769.580042] usb 1-9: new high speed USB device using ehci_hcd and address 7
kernel: [ 2769.714782] scsi8 : usb-storage 1-9:1.0
kernel: [ 2770.713937] scsi 8:0:0:0: Direct-Access     8192MB   flash drive      1.00 PQ: 0 ANSI: 2
kernel: [ 2770.714535] scsi 8:0:0:1: Direct-Access     8192MB   flash drive      1.00 PQ: 0 ANSI: 2
kernel: [ 2770.715734] sd 8:0:0:0: Attached scsi generic sg3 type 0
kernel: [ 2770.716108] sd 8:0:0:1: Attached scsi generic sg4 type 0
kernel: [ 2770.722175] sd 8:0:0:0: [sdc] 962560 512-byte logical blocks: (492 MB/470 MiB)
kernel: [ 2770.722657] sd 8:0:0:0: [sdc] Write Protect is on
kernel: [ 2770.731078] sd 8:0:0:1: [sdd] 14012416 512-byte logical blocks: (7.17 GB/6.68 GiB)
kernel: [ 2770.731215]  sdc:
kernel: [ 2770.738251] sd 8:0:0:1: [sdd] Write Protect is off
kernel: [ 2770.880328] 
kernel: [ 2770.885876] sd 8:0:0:0: [sdc] Attached SCSI removable disk
kernel: [ 2770.887442]  sdd: unknown partition table
kernel: [ 2771.049605] sd 8:0:0:1: [sdd] Attached SCSI removable disk

So, symptoms are typical for U3-like devices: two separate devices inside of a single flash device. Windows sees it also as two identical usb devices, and mounts two separate drives to system, whereas first one presents itself as a CDROM device, holding a write-protected content, and second is a regular flash-disk partition, that "can" be written to. However, it seems like it's broken in some weird way, since it won't let me write anything to it, format it, nothing, but that's not the issue right now.

Question: How can I unlock entire USB stick so it appears to system as a single, 8GB device which can be partitioned and used normally, without restrictions?

Since it appeared to be an U3 device, I have tried standard utilities: both U3 Uninstaller by u3.com (found on SoftPedia), and opensource u3_tool from sourceforge (on both Windows and Linux). First utility failed to even detect USB stick as U3 device (simply stood idle while I re-plugged stick several times), while second tool failed with some obscure error about SCSI command unable to do something (I might be able to provide exact errors when I switch back to windows). u3_tool -i /dev/sg3 (Display device info) fails with

u3_partition_info() failed: Device reported command failed: status 1

...and every other option fails with same error, minus first part which states which command precisely has failed.

So, apparently, this isn't a U3 device. Or, if it is, it doesn't behave like one.

I read on a few occasions that this device protection is done by special command sent to device which tells it to lock itself, and so there should be an unlock command, that would set drive straight.

Does anyone have any idea about what could I do to this device to fix it?

P.S. I also mentioned a problem with being unable to use second "drive", but I'll tackle that problem when (and if) I manage to merge those two devices into one...