-
as seen on Ask Ubuntu
- Search for 'Ask Ubuntu'
In Windows 7, my computer can automatically get a IPV6 global address and use IPV6 network, but in Ubuntu Natty, I can't find out how to let stateless configuration work.
My network is a university campus network,so I don't need tunnels. I think if one thing can silently and successfully be accomplished…
>>> More
-
as seen on Server Fault
- Search for 'Server Fault'
In my Fritzbox it states the following:
IPv6-Adresse: 2a02:8070:600::14b6:c7******, Gültigkeit: 100465/86065s
IPv6-Präfix: 2a02:8070:62c:3200::/56, Gültigkeit: 100464/86064s
I am not able to connect to IPv6 Addresses from computers configured by the fritzbox, because they get an address with prefix…
>>> More
-
as seen on Server Fault
- Search for 'Server Fault'
I have a network that advertises IPv6 addresses through IPv6 autoconfig. To allow DNS lookups and to have fancy IP addresses, we setup "static" IPv6 addresses through /etc/network/interfaces:
auto eth0
iface eth0 inet dhcp
iface eth0 inet6 static
address a:b:c:d:e::f
netmask 64
Whenever…
>>> More
-
as seen on How to geek
- Search for 'How to geek'
IPv6 is extremely important for the long-term health of the Internet. But is your Internet service provider providing IPv6 connectivity yet? Does your home network support it? Should you even care if you’re using IPv6 yet? Switching from IPv4 to IPv6 will give the Internet a much larger pool…
>>> More
-
as seen on Server Fault
- Search for 'Server Fault'
Long story short I am having issues with IPv6 using a 6rd tunnel with my ISP, charter business. They offer a 6rd tunnel that I think I have properly set up, but the server doesn’t reply to every ipv6 request. When the server has the network interfaces idle with no traffic for about 10 minutes, then…
>>> More
-
as seen on Server Fault
- Search for 'Server Fault'
Hello,
I have two different questions, the first one could be stupid.
I was reading about IPV6 and ended up in this site http://test-ipv6.com/ that says that I have a public IPV6 with Teredo tunneling. I don't understand if this Teredo is a software thing, does it have to with my ISP, is it enabled…
>>> More
-
as seen on Server Fault
- Search for 'Server Fault'
All I want to achieve is to establish connection to my simple server (written in C# using TcpListener class, if it makes any difference), on my computer which is behind NAT. It has some IPv6 address (it's public IP, starting with 2001:0) on Teredo interface. However, I cannot even ping it from outside…
>>> More
-
as seen on Server Fault
- Search for 'Server Fault'
Today while doing some routine maintenance I discovered that my internet-connected network adapter was using a 6to4 tunnel to connect to my ISP. Some self-eduction on Teredo seemed to indicate quite a few potential security vulnerabilities with using the protocol. I have disabled my network adapter…
>>> More
-
as seen on Server Fault
- Search for 'Server Fault'
I have a server behind NAT, which I want to be able to access from the internet. I want to do it over ipv6. I guess my question falls into two:
I don't think teredo is working on it. I have ethernet adapter ipv6 set to automatic, however I don't think there connectivity is there. So, how do I enable…
>>> More
-
as seen on Server Fault
- Search for 'Server Fault'
i'm trying to get Teredo to function on my machine.
Most routers, it seems, refuse to forward packets from any host other than the one i specifically connected to first. Teredo requires full Cone NAT in order to function.
Does any router, hardware or software, allow full cone NAT?
Is this an oversight…
>>> More
