Adding a single 300Gb SCSI drive to poweredge 2850

Posted by John Steele on Server Fault See other posts from Server Fault or by John Steele
Published on 2011-06-26T05:51:13Z Indexed on 2011/06/26 8:23 UTC
Read the original article Hit count: 423

Filed under:

raid

|

dell-poweredge

|

scsi

I have a 2850 setup with 3 146Gb drives, two partitions 1 12GB system with server 2003 sp2 and 1 261Gb Data. I am strapped on disk space on the data partition having to push data around. I wanted to add a 300Gb single drive for lesser critical data, is this possible? Or is it best to add 2 300Gb drives for another RAID 1 configuration? This is my church network and while it is mission critical it is not enterprise so I can take it down for a few hours. Any pointers to documentation or direct help would be greatly appreciated. John

© Server Fault or respective owner

Related posts about raid

Booting from integrated RAID controller when another RAID controller is installed in a PCIe slot

as seen on Server Fault - Search for 'Server Fault'
I have a GA MA785GT UD3H motherboard with Windows Server 2008 R2 installed on a RAID1 using the on-board RAID controller. I have now installed a RocketRaid 2680 controller and set up a RAID5 for all my data to be stored on. Unfortunately I now cannot boot from the RAID1 anymore, the PC is trying… >>> More
Onboard RAID vs Software RAID

as seen on Server Fault - Search for 'Server Fault'
My motherboard, an Asus M4a79t Deluxe, advertises RAID 0/1/5 capabilities. My limited understanding is that onboard RAID is better than software RAID. Is this necessarily true? Is an onboard RAID controller closer in performance to a software controller or a dedicated hardware controller? >>> More
RAID-1 and regular drive removal (using RAID-1 as a backup measure)

as seen on Super User - Search for 'Super User'
Is using mdadm's RAID-1 of 2 partitions (one on laptop's internal HDD, one on external HDD) a good idea. I want the system to work as RAID-1 if both drives are present, work as regular volume (degradad RAID-1) if external HDD is unplugged and quickly resync when I plug external HDD again. Questions: Is… >>> More
Explain difference in SQLIO numbers for RAID 0 versus RAID 5 over 6 disks

as seen on Stack Overflow - Search for 'Stack Overflow'
When using the SQLIO benchmark tool on a 4-core Dell server with 6 15k 450GB (fast) drives, RAID 0, we found the max throughput was 2MB per second. But when configured as RAID 5, we get 30 MB per second. It seems that the RAID controller, Dell Perc 5i integrated controller, is maxing out the… >>> More
RAID 5 RECONSTRUCT with RAID Reconstructor

as seen on Server Fault - Search for 'Server Fault'
I have Dell Poweredge server 2600 with Raid 5 in 3 hard drive Scsi 36gb each, it was fail to boot sinc the third drive is offline. I attached Sata card adapter to Sata hard drive and install OS SERVER 2003 to it, downloaded drivers for Raid and everything goes fine when I use recovery data software… >>> More

Related posts about dell-poweredge

How to speed up boot sequence on a Dell PowerEdge 1950

as seen on Server Fault - Search for 'Server Fault'
Everytime I had to reboot one of the Dell PowerEdge 1950 we have, there are very long tests and with them the boot sequence becomes incredibly long. Is there a way to turn off all these tests (or at least speeding them up) ? >>> More
Dell Poweredge 2650 RAM Upgrade

as seen on Server Fault - Search for 'Server Fault'
Hi, I bought an old Dell Poweredge 2650 off ebay to use as a dev server, but I need to get more RAM for it. From what I understand there were 2 versions of the 2650 released, with the older version only supporting PC1600 RAM (200MHz) and the 2nd version supporting PC2400. Unfortunately Dell thought… >>> More
How do you get - Better than 1024x768 Driver for 64 bit Dell PowerEdge Server

as seen on Super User - Search for 'Super User'
How do you get better than 1024x768 resolution? Just installed MS Server 2008 64bit on a Dell PowerEdge 64bit box (works OK - Previously running MS Server 2003 32bit) After install - gives a a max resultion of 1024x768 I want to change the reslution to 1280x1024 (Same LCD Worked OK on server 2003) When… >>> More
Help to set up RAID on a DELL Poweredge 400SC

as seen on Server Fault - Search for 'Server Fault'
I have a FastTrak S150 TX2 raid controller that I have downloaded the driver for. I am installing WinXP fresh but don't have a floppy disk. Is there another way to load these drivers on boot? Anyone? Anyone at all... >>> More
Can the Dell PowerEdge T320 boot from a USB stick in hard drive emulation mode?

as seen on Server Fault - Search for 'Server Fault'
I am trying to install FreeNAS on a Dell PowerEdge T320. I've followed the instructions here (http://doc.freenas.org/index.php/Burning_an_IMG_File) to write the .img file to four different USB sticks with dd if=FreeNAS-9.2.1.5-RELEASE-x64.img of=/dev/sde, but I can't boot off of any of them. When… >>> More