How do you configuring vlans/trunk on a Cicso ASA 5510

Posted by Sam Sanders on Server Fault See other posts from Server Fault or by Sam Sanders
Published on 2011-11-30T22:55:28Z Indexed on 2011/12/01 2:02 UTC
Read the original article Hit count: 603

Filed under:

cisco-asa

|

vlan

|

trunk

I have a Cicso ASA 5510 that I want to connect to 2 Dell PowerConnect 5500 linked in a Switch Stack. I want to connect a trunking line to each switch so if one switch dies the other works. The problem is I can't seem to do anything thing with vlans on the 5510 using the "Cisco ASDM 6.4 for ASA" . Do I need to use CLI for this, or is it just not possible? I'm new at networking so any advice would be helpful.

© Server Fault or respective owner

Related posts about cisco-asa

Cisco ASA bonding/teaming/port-channel capabilities

as seen on Server Fault - Search for 'Server Fault'
Hello, This seemed to me like a really simple question that I would be able to answer by myself but I have not been able to find any info on this subject. I have a Cisco ASA 5510 which has 4 FastEthernet interfaces. I was wondering if it would be possible to use 2 or 3 of these interfaces as a port-channel… >>> More
Plugging the Cisco ASA Security Hole

as seen on Internet.com - Search for 'Internet.com'
Cisco dominates the networking hardware market, and with its Adaptive Security Appliance it is extending its reach into network security. The ASA, however, can introduce a security issue. Learn how to resolve it so you can get the most out of this powerful tool. >>> More
Enable Cisco ASA as an SSH Tunneling

as seen on Server Fault - Search for 'Server Fault'
I am trying to utilize my Cisco ASA as a SSH Tunnel. I've configured this before when using a Linux server as the SSH target, however I cannot seem to get it to work with the ASA. I have configured and enabled SSH on the Cisco ASA, as well as a username that I can SSH to the console, however the SSH… >>> More
QoS basics on a Cisco ASA

as seen on Server Fault - Search for 'Server Fault'
Could someone briefly explain how to use QoS on Cisco ASA 5505? I have the basics of policing down, but what about shaping and priorities? Basically what I'm trying to do is carve out some bandwidth for my VPN subnets (in an object-group called priority-traffic). I've seen this Cisco QoS document… >>> More
Configuring Cisco ASA 5510 to assign static IP address based on MAC address

as seen on Server Fault - Search for 'Server Fault'
Hi, We have a CISCO ASA 5510 at work. We want to configure the same such that it can serve specific IP addresses based on the MAC address of the clients. Any help would be greatly appreciated. Thanks in advance -knd >>> More

Related posts about vlan

Cisco vlan entry missing in vlan.dat, but appears in running-config

as seen on Server Fault - Search for 'Server Fault'
One of our vlan's (ID: 104) stopped working suddenly and computers on that vlan failed when trying to obtain a dhcp ip address. On the Cisco switch if we do show vlan, this command is supposed to shows the vlans in the vlan.dat file. We notice it has every other vlan except the one that is now missing… >>> More
Unable to access VLAN host from VLAN interface in CentOS

as seen on Server Fault - Search for 'Server Fault'
I am playing with VLAN (Virtual LAN) configuration on CentOS 6.4. I have 2 interfaces, eth0 and eth1. I have configured 2 VLAN interfaces eth0.20 and eth0.30 as #file: ifcfg-eth0.20 #------------- VLAN=yes DEVICE=eth0.20 TYPE=Ethernet ONBOOT=yes NM_CONTROLLED=no BOOTPROTO=static IPADDR=192.168… >>> More
Multiple vlans access to shared pbx system

as seen on Server Fault - Search for 'Server Fault'
I'm new to networking and was looking for some assistance. First off I'm using packet tracer to diagram my scenario as I will be receiving my equipment next week to deploy. Hardware to be used: 2 catalyst 3560 switches all connect to a sonic wall router I have two companies that work in the… >>> More
VLAN ID 4095 for guest VLAN tagging

as seen on Server Fault - Search for 'Server Fault'
Just want to know if it's true that if you use the VLAN ID 4095 for guest VLAN tagging, then vMotion will not work correctly as there is nowhere to pass back the reverse arp to? So, the problem we have noticed is when we have vmotioned VM's that are tagged on our trunk network, you cannot ping them… >>> More
vlan change via scvmm not working

as seen on Server Fault - Search for 'Server Fault'
Hi i have a windows 2008 R2 hyper-v server which is managed via scvmm 2008 R2. the guest os running on the hyper-v server is winxp with sp3. if i change the vlan id via scvmm the guest doesn't get an ip via dhcp i looked in the properties of the vm with the hyper-v mmc an see the vlan changed correctly… >>> More