How to bridge multiple wireless access points (and internet entry points) into one network

Posted by amccormack on Server Fault See other posts from Server Fault or by amccormack
Published on 2012-04-03T02:57:17Z Indexed on 2012/04/03 5:32 UTC
Read the original article Hit count: 523

Filed under:

networking

|

bridge

I have two DSL lines coming in to wireless access points and then running to a RV082 Gateway/Bridge. The gateway then runs to a switch, which runs to multiple PCs and a Printer (See picture below). Normally, I would set up the wireless access points behind the gateway, but they are also the modems for the dsl. I have found that I can not print to the network printer if I am connected to the wireless network, but only if I am connected to the wired network.

How can I configure the Gateway and APs (Routers) so that the PCs and Printer are all on the same internal network?

I have tried turning DHCP off or redirect on the APs and redirect them to the Gateway. However, neither of these worked. Furthermore, I tried pinging the Gateway from the AP but got no response.

enter image description here

© Server Fault or respective owner

Related posts about networking

Networking stopped working on Ubuntu

as seen on Super User - Search for 'Super User'
I installed Ubuntu 10.04 through the Wubi installer (Funny, I installed it today and thought I would have gotten 10.10). I had a network connection and everything was working fine. I rebooted my coumputer a couple of times and then suddenly, I could not connect to the network and when I click the… >>> More
Troubles with start up defenition of networking service in Ubuntu

as seen on Super User - Search for 'Super User'
I use Ubuntu 12.04.1. I put attention that networking script starting in runlevel 0: user@comp:/etc/rc0.d$ chkconfig -l networking networking 0:on 1:off 2:off 3:off 4:off 5:off 6:off When I try to move it working to appropriate run levels I get error: user@comp:/etc/rc0… >>> More
Installing the Elgg Social Networking CMS

as seen on Internet.com - Search for 'Internet.com'
One Open Source CMS that stands out above the rest for small businesses and personal networks is the Elgg open source "social engine," which can be used to create social applications. Scott Clark shows you how to install and get started with this social networking CMS. >>> More
OAuth: Token-Based Authorization for the Social Networking Age

as seen on Internet.com - Search for 'Internet.com'
The OAuth token-based authorization system allows users to grant third-party access to their resources without sharing their usernames and passwords. It's perfect for the age of data scattered across many social networking sites. >>> More
OAuth: Token-Based Authorization for the Social Networking Age

as seen on Internet.com - Search for 'Internet.com'
The OAuth token-based authorization system allows users to grant third-party access to their resources without sharing their usernames and passwords. It's perfect for the age of data scattered across many social networking sites. >>> More

Related posts about bridge

How do I make Linux recognize a new SATA /dev/sda drive I hot swapped in without rebooting?

as seen on Server Fault - Search for 'Server Fault'
Hot swapping out a failed SATA /dev/sda drive worked fine, but when I went to swap in a new drive, it wasn't recognized: [root@fs-2 ~]# tail -18 /var/log/messages May 5 16:54:35 fs-2 kernel: ata1: exception Emask 0x10 SAct 0x0 SErr 0x50000 action 0xe frozen May 5 16:54:35 fs-2 kernel: ata1: SError:… >>> More
How do I make Linux recognize a new SATA /dev/sda drive I hot swapped in without rebooting?

as seen on Server Fault - Search for 'Server Fault'
Hot swapping out a failed SATA /dev/sda drive worked fine, but when I went to swap in a new drive, it wasn't recognized: [root@fs-2 ~]# tail -18 /var/log/messages May 5 16:54:35 fs-2 kernel: ata1: exception Emask 0x10 SAct 0x0 SErr 0x50000 action 0xe frozen May 5 16:54:35 fs-2 kernel: ata1: SError:… >>> More
WPA2 authentication fails on Ubuntu 12.04 using Rosewill RNX-N1

as seen on Ask Ubuntu - Search for 'Ask Ubuntu'
Decided to reduce the clutter in the house and replace a wired connection with a wireless one on my wife's system using USB network device Rosewill RNX-X1. I can see and connect to unprotected network, but WPA2 authentication repeatedly fails. RNX-X1 works on other systems (including TV); also have… >>> More
WPA2 authentication fails using USB network devices (Linksys and Rosewill)

as seen on Ask Ubuntu - Search for 'Ask Ubuntu'
Decided to reduce the clutter in the house and replace a wired connection with a wireless one on my wife's system using USB network device Rosewill RNX-X1. I can see and connect to unprotected network, but WPA2 authentication repeatedly fails. Tried the same with a Linksys USB network adapter. … >>> More
Using the Onboard VGA output with a PCIe video card. Both nVidia

as seen on Ask Ubuntu - Search for 'Ask Ubuntu'
I have 2 video cards, one On board, a nVidia 6150SE nForce 430 and a PCIe nVidia GeForce GT 220 1GB DDR2 RAM I have already configured the PCIe card to use the dual monitor feature, using the VGA and HDMI ports, but now I want to add a third monitor, using the On board VGA port I have managed to… >>> More