rip in RouterSim

Posted by Olga Anastasiadou on Server Fault See other posts from Server Fault or by Olga Anastasiadou
Published on 2012-06-02T06:18:08Z Indexed on 2012/06/02 10:43 UTC
Read the original article Hit count: 423

Filed under:

ip

|

subnet

|

rip

I have to design a network given IPs 146.124.0.0/16 and 146.124.10.0/24. My given requirements are : at least 60 more subnets and maximum 1000 hosts per subnet and use of RIP.

I have 3 routers (RA1, RA2, RA3) and 3 subnets (Sales, Logistic and Deposit). I gave WAN1 (RA1-RA3): 146.124.10.0/30, WAN2 (RA2-RA3) : 146.124.10.4/30 and WAN3 (RA1-RA2) : 146.124.10.8/30 and Sales : 146.124.0.0/22, Logistic: 146.124.4.0 and Deposit : 146.124.8.0. When I tried to configure RIP protocol, it didn’t work (I use routerSim 6). What am I doing wrong?

Can anyone help please????

© Server Fault or respective owner

Related posts about ip

Getting USB Wifi device to work

as seen on Ask Ubuntu - Search for 'Ask Ubuntu'
I have been trying to get an Olitec Wifi N USB dongle to work. At first it lit up but wouldn't connect. A little Googling suggested that it would need ndiswrapper to make it work. After installing and trying to add driver with ndisgtk, I got the error message FATAL: Module ndiswrapper not found.… >>> More
Cisco 800 series won't forward port

as seen on Server Fault - Search for 'Server Fault'
Hello ServerFault, I am trying to forward port 444 from my cisco router to my Web Server (192.168.0.2). As far as I can tell, my port forwarding is configured correctly, yet no traffic will pass through on port 444. Here is my config: ! version 12.3 service config no service pad service tcp-keepalives-in service… >>> More
Cisco 881 losing NAT NVI translation config after reload

as seen on Server Fault - Search for 'Server Fault'
This is a weird one, so I'll try to explain in as much detail as I can so I'm giving the whole picture. As I've mentioned in my other questions, I'm in the process of setting up a new Cisco 881 as my WAN router and NAT firewall. I'm facing an issue where NAT NVI rules that I have configured are not… >>> More
Bind an ip address to Postfix as outgoing ip

as seen on Server Fault - Search for 'Server Fault'
Is that possible to bind all available public ip addresses on a server to one Postfix instance as its outgoing ip pool and let it choose a random ip or specified ip from the pool each time it sends out an email? If above is not possible, can it be configured to listen on one public ip address per… >>> More
What approach to take for SIMD optimizations

as seen on Stack Overflow - Search for 'Stack Overflow'
Hi, I am trying to optimize below code for SIMD operations (8way/4way/2way SIMD whiechever possible and if it gives gains in performance) I am tryin to analyze it first on paper to understand the algorithm used. How can i optimize it for SIMD:- void idct(uint8_t *dst, int stride, int16_t *input… >>> More

Related posts about subnet

Can I subnet a subnet?

as seen on Server Fault - Search for 'Server Fault'
Apologies in advance for the botched terminology. I have read the Server Fault Subnet Wiki but this is more of an ISP question. I currently have a /27 block of public IPs. I use give my router the first address in this pool and then use 1-to-1 NAT for all the servers behind the firewall, so that… >>> More
Connecting to a remote server through OpenVPN when local network subnet conflicts with remote network's subnet

as seen on Server Fault - Search for 'Server Fault'
After connecting to a remote location via OpenVPN, I am trying to access a server on a network that exists on a subnet such as 10.0.1.0/24. However, the network I am trying to access this remote server from is on the same subnet: 10.0.1.0/24. I am unable to connect to my remote server via typing… >>> More
How to Route Traffic in Case PPTP Remote Client is on Same Subnet as Server

as seen on Server Fault - Search for 'Server Fault'
I've a PPTP server setup on my local home network (192.168.1.0/24, pfSense). Now sometimes when I'm away and want to connect remotely my client (Windows 7) is also on the same network because e.g. the hotel has set it up the same way. Thus the connection works, but I can't reach any PC on my home… >>> More
Changing subnet-mask of class-c network host to 255.255.0.0

as seen on Server Fault - Search for 'Server Fault'
We have a existing class-c network with IP address range 11.22.33.44/24 (just for example). My domain controller has been configured within this subnet. So all servers within this subnet have subnet mask configured to 255.255.255.0. Now we have got a new subnet with IP address 11.22.88.99/24 (note… >>> More
Issues resolving DNS entries for multi-homed servers

as seen on Server Fault - Search for 'Server Fault'
This is difficult to explain, so bear with me. We have 2 domain controllers, each multi-homed to straddle 2 internal subnets, (subnet A and subnet B) and provide dns, dhcp, and ldap authentication. Both domain controllers each have 2 DNS entries. both entries have identical host names, but correspond… >>> More