Force10 S4810 "Overlapping route for management interface"

Posted by Erik Reynolds on Server Fault See other posts from Server Fault or by Erik Reynolds
Published on 2012-09-10T14:23:01Z Indexed on 2012/09/30 15:40 UTC
Read the original article Hit count: 2966

Filed under:

networking

|

force10

We just got in a pair of Force10 S4810s and are getting tripped up on what should be a very basic configuration step.

The S4810 has a gigabit copper management port (though ultimately we'd like to not use that and just trunk in a management vlan). We followed the configuration commands verbatim from a rapid config guide and keep getting a weird error. "Overlapping route for Management Interface."

http://i.imgur.com/ojaTQ.png

Current running config per request: http://pastebin.com/995v4RSG

Any thoughts? I'm pretty baffled. (FWIW: I'm not at all a networking person -- though I'm quickly learning!)

Thanks for your help!

© Server Fault or respective owner

Related posts about networking

Networking stopped working on Ubuntu

as seen on Super User - Search for 'Super User'
I installed Ubuntu 10.04 through the Wubi installer (Funny, I installed it today and thought I would have gotten 10.10). I had a network connection and everything was working fine. I rebooted my coumputer a couple of times and then suddenly, I could not connect to the network and when I click the… >>> More
Troubles with start up defenition of networking service in Ubuntu

as seen on Super User - Search for 'Super User'
I use Ubuntu 12.04.1. I put attention that networking script starting in runlevel 0: user@comp:/etc/rc0.d$ chkconfig -l networking networking 0:on 1:off 2:off 3:off 4:off 5:off 6:off When I try to move it working to appropriate run levels I get error: user@comp:/etc/rc0… >>> More
Installing the Elgg Social Networking CMS

as seen on Internet.com - Search for 'Internet.com'
One Open Source CMS that stands out above the rest for small businesses and personal networks is the Elgg open source "social engine," which can be used to create social applications. Scott Clark shows you how to install and get started with this social networking CMS. >>> More
OAuth: Token-Based Authorization for the Social Networking Age

as seen on Internet.com - Search for 'Internet.com'
The OAuth token-based authorization system allows users to grant third-party access to their resources without sharing their usernames and passwords. It's perfect for the age of data scattered across many social networking sites. >>> More
OAuth: Token-Based Authorization for the Social Networking Age

as seen on Internet.com - Search for 'Internet.com'
The OAuth token-based authorization system allows users to grant third-party access to their resources without sharing their usernames and passwords. It's perfect for the age of data scattered across many social networking sites. >>> More

Related posts about force10

Force10 S4810 "Overlapping route for management interface"

as seen on Server Fault - Search for 'Server Fault'
We just got in a pair of Force10 S4810s and are getting tripped up on what should be a very basic configuration step. The S4810 has a gigabit copper management port (though ultimately we'd like to not use that and just trunk in a management vlan). We followed the configuration commands verbatim from… >>> More
PXE booting LACP hosts on Force10 S50N with FTOS

as seen on Server Fault - Search for 'Server Fault'
Hardware: S50N Firmware: FTOS 8.4.2.6 Problem: We're trying to PXE boot some servers that are connected via port-channel interfaces with LACP. Current Work-around: we PXE boot a server with a single interface (eth0), and then use a Perl script to turn up the port-channel interfaces after the server… >>> More
Force10 layer 3 switches

as seen on Server Fault - Search for 'Server Fault'
We've been running Cisco and dell layer 3 switches. The former are expensive and reliable, the latter a lot cheaper and fraught with issues. Anyone has positive experience with the core Force10 switches (and edge switches as well)? >>> More
Force10 S60 remote management

as seen on Server Fault - Search for 'Server Fault'
We've got a Force10 S60 switch to replace an older Cisco. I can't find a way to give the switch itself an IP address on the local VLAN so I can ssh to it. The config guide talks about using either a management interface on a separate management network or dedicating e.g. a gigabit port as a management… >>> More
What to look for in a switch with LAN/WAN verses an iSCSI SAN?

as seen on Server Fault - Search for 'Server Fault'
I'm setting up a VMWare ESXi 5 environment with 3 server nodes. Dell recommended 2x Force10 S60 switches shared (iSCSI SAN, LAN/WAN). The S60 switches are extremely powerful. They have 1.25 GB of buffer cache, < 9us latency. But they are very expensive (online price ~$15k per switch, actual quote… >>> More