Search Results

Search found 17 results on 1 pages for '2960'.

Page 1/1 | 1 

  • How do I Implement VLAN Rate Limiting or QOS for a Cisco 2960?

    - by evolvd
    I have a 2960 that I need to limit the uplink port to 50Mbps for 3 vlans and 350Mbps for another vlan. Would the following config achieve that or is this even possible for the 2960? class-map match-any VLAN50-51-52 match vlan 50-52 class-map match-any VLAN53 match vlan 53 policy-map 50MB_RATE_LIMIT class VLAN50-51-52 police 50000000 5000000 exceed-action drop class VLAN53 police 350000000 35000000 exceed-action drop ! interface GigabitEthernet0/23 service-policy output 50MB_RATE_LIMIT service-policy input 50MB_RATE_LIMIT

    Read the article

  • How do I Implement Per VLAN Rate Limiting or QOS for a Cisco 2960?

    - by evolvd
    I have a 2960 that I need to limit the uplink port to 50Mbps for 3 vlans and 350Mbps for another vlan. Would the following config achieve that or is this even possible for the 2960? class-map match-any VLAN50-51-52 match vlan 50-52 class-map match-any VLAN53 match vlan 53 policy-map 50MB_RATE_LIMIT class VLAN50-51-52 police 50000000 5000000 exceed-action drop class VLAN53 police 350000000 35000000 exceed-action drop ! interface GigabitEthernet0/23 service-policy output 50MB_RATE_LIMIT service-policy input 50MB_RATE_LIMIT

    Read the article

  • How to configure CISCO switch 2960 for port-based address allocation on a single port only?

    - by Jack
    CISCO 2960 allows you to configure so-called Port-Based address allocation. It makes the switch to associate IP address it is giving out via DHCP with port-identifier, which is random, switch created identifier. In practice it means that any machine connected to such configured port will always get the same IP address, regardless of what that machine's MAC address is. I want to have that feature configured on --some ports-- only. But no matter what commands I try it seems that this can only be done for all ports, all for none. Even though CISCO manual seems to indicate there's both global and per-port command to enable that. Here are relevant commands from CISCO manual: configure terminal ip dhcp use subscriber-id client-id (this configures the DHCP server to globally use the subscriber ID as the client ID on all incoming DHCP messages) interface FastEthernet0/1 ip dhcp server use subscriber-id client-id (Optional: Configures the DHCP server to use the subscriber ID as the client ID on all incoming DHCP messages on the interface) but it appears if I configure only per-interface than there's no effect at all, if I configure globally and per interface - CISCo behaves as if all ports were configured to use that feature. Any ideas?

    Read the article

  • Determining the health of a Cisco switch port?

    - by ewwhite
    I've been chasing a packet-loss and network stability issue for a handful of end-users on an internal network for the past few days... These issues surfaced recently, however, the location was struck by lightning six weeks ago. I was seeing 5-10% packet loss between a stack of four Cisco 2960's and several PC's and phones on the other side of a 77-meter run. The PC's were run inline with the phones over a trunked link. We were seeing dropped calls and interruptions in client-server applications and Microsoft Exchange connectivity. I tried the usual troubleshooting steps remotely, having a local technician do the following during breaks in user and production activity: change cables between the wall jack and device. change patch cables between the patch panel and switch port(s). try different switch ports within the 2960 stack. change end-user devices with known-good equipment (new phones, different PC's). clear switch port interface counters and monitor incrementing errors closely. (Pastebin output of sh int) Pored over the device logs and Observium RRD graphs. No link up/down issues from the switch side. change power strips on the end-user side. test cable runs from the Cisco 2960 using test cable-diagnostics tdr int Gi4/0/9 (clean)* test cable runs with a Tripp-Lite cable tester. (clean) run diagnostics on the switch stack members. (clean) In the end, it took three changes of switch ports to find a stable solution. The only logical conclusion is that a few Cisco 2960 switch ports are bad or flaky... Not dead, but not consistent in behavior either. I'm not used to seeing individual ports die in this manner. What else can I test or check to determine if these devices are bad? Is it common for single ports to have problems, rather than a contiguous bank of ports? BTW - show cable-diagnostics tdr int Gi4/0/14 is very cool... Interface Speed Local pair Pair length Remote pair Pair status --------- ----- ---------- ------------------ ----------- -------------------- Gi4/0/14 1000M Pair A 79 +/- 0 meters Pair B Normal Pair B 75 +/- 0 meters Pair A Normal Pair C 77 +/- 0 meters Pair D Normal Pair D 79 +/- 0 meters Pair C Normal

    Read the article

  • Is my Cisco switch port bad?

    - by ewwhite
    I've been chasing a packet-loss and network stability issue for a handful of end-users on an internal network for the past few days... These issues surfaced last week, however the location was struck by lightning six weeks ago. I was seeing 5-10% packet loss between a stack of four Cisco 2960's and several PC's and phones on the other side of a 77-meter run. The PC's were run inline with the phones over a trunked link (switchport configuration pastebin). We were seeing dropped calls and interruptions in client-server applications and Microsoft Exchange connectivity. I tried the usual troubleshooting steps remotely, having a local technician do the following during breaks in user and production activity: change cables between the wall jack and device. change patch cables between the patch panel and switch port(s). try different switch ports within the 2960 stack. change end-user devices with known-good equipment (new phones, different PC's). clear switch port interface counters and monitor incrementing errors closely. (Pastebin output of sh int) Pored over the device logs and Observium RRD graphs. No link up/down issues from the switch side. change power strips on the end-user side. test cable runs from the Cisco 2960 using test cable-diagnostics tdr int Gi4/0/9 (clean)* test cable runs with a Tripp-Lite cable tester. (clean) run diagnostics on the switch stack members. (clean) In the end, it took three changes of switch ports to find a stable solution. The only logical conclusion is that a few Cisco 2960 switch ports are bad or flaky... Not dead, but not consistent in behavior either. I'm not used to seeing individual ports die in this manner. What else can I test or check to determine if these devices are bad? Is it common for single ports to have problems, rather than a contiguous bank of ports? BTW - show cable-diagnostics tdr int Gi4/0/14 is very cool... Interface Speed Local pair Pair length Remote pair Pair status --------- ----- ---------- ------------------ ----------- -------------------- Gi4/0/14 1000M Pair A 79 +/- 0 meters Pair B Normal Pair B 75 +/- 0 meters Pair A Normal Pair C 77 +/- 0 meters Pair D Normal Pair D 79 +/- 0 meters Pair C Normal

    Read the article

  • Connecting office to data center via Metro-ethernet

    - by Eric
    I am installing a metro ethernet link from my office to my data center. The office will have a cisco 3750 with several vlans. The data center end will have a more complicated set up. The metro e from the office will connect to a 2960, which will have two other 2960s with a few vlans and a 2811 router connected to it for connectivity to our other environments and the internet. I am looking at implementing this by connecting the office 3750 and the data center 2960 with a dot1q trunk and doing all routing at the 2811. I will configure subinterfaces for gateways for each of the vlans on the 2811. I work for a small company and don't have much of a budget for an ideal architecture. I can post a simple diagram if needed for clarification. Is there anything I am missing here? I feel like I am forgetting something very basic and want to make sure I eliminate any boneheaded mistakes.

    Read the article

  • SCOM2012 monitor detail changes on switch

    - by siyang
    Could I use SCOM2012 monitor the changes on switch(CISCO 3750 2960 4906 etc), such as VLAN changes, Port shutdown, open any services on switch. I noticed there is one reports named configuration changes report, but seems like no any detail configuration could be monitor on switch? Should I download any MP to monitor the detail changes on SW. Really appreciated your suggestion. Thanks and Regards Siyang

    Read the article

  • DHCPOFFER delay VLAN

    - by john883
    I have configured two VLANs [ 15 and 16 ] and a trunkport on a Cisco Catalyst 2960. The trunkport is connected to eth2 on a Linux server The server is configured to support VLAN's and the interfaces eth2.15 eth2.16 is configured with ip addresses on two different subnet. dhcp3-server is running on the same server and hands out IP-addresses to the VLANs. When connecting a client to a port that is configured in ex. VLAN 15 and requesting a IP-address, i experience a long delay before recieving a DHCPOFFER, around 30 seconds or so, the client needs to send a DHCPDISCOVER about five times but will always recieve a DHCPOFFER. Any suggestion why this delay is happening?

    Read the article

  • Cisco: changing VTP mode server/client to transparent

    - by J. Smith
    I have around 40 L2 switches (2960, 3560, 3500, 3750) running in VTP client mode and one L3 switch (6500) running in VTP server mode, all connected together. I would like to switch everything in VTP transparent mode without any interruption of service. I've already test on a poc version with 3 switches (Catalyst 2950, 3560 and 3750). Using serial and SSH connection, it is seems working but i'm not sure it is enough representative compare to the real network. Knowing that the VTP Pruning is enabled, I am wondering what would be the best procedure to proceed the changement. I've read that we could lost connection by keeping it enabled. Should I change the server or clients first? Is it important to change the VTP domain and VTP Pruning parameters?

    Read the article

  • Second Monitor stays black/in power save mode

    - by Rob
    I'm using two Monitors, a Belinea o.display 1 (Recognized as a Rogen Tech Distribution Inc 20" by Ubuntu, but working fine) on the DVI-Output (connected via DVI-to-VGA-adapter) as my primary Monitor and a Dell 19" (Recognized correctly) on the HDMI-output (via HDMI-to-DVI adapter) as secondary monitor. The graphics controller is a GeForce 9500 GS. I'm running a fully updated Ubuntu 13.04 with nouveau 1:1.0.7-0ubuntu1. The problem is that the second monitor (Dell) never seems to come out of standby during boot: the screen stays black and the status led on the monitor stays orange (it's green when it's on). It is correctly recognized an the size of the desktop is set accordingly, it just stays black. Changing any setting via xrandr/arandr/etc. does nothing. The on-screen-menu of the monitor reports it to be in power save mode. When using the proprietary NVIDIA-Drivers, the second monitor works just find. But these drivers cause a lot of other problems on my system, so i would really like to avoid them. On Ubuntu 12.10 i had found a workaround: When moving the relative position of the second monitor slightly down and the up again, it would turn on and function normally: xrandr --output DVI-I-1 --mode 1680x1050 --pos 1280x0 --rotate normal --output HDMI-1 --mode 1280x1024 --pos 0x88 --rotate normal sleep 2 xrandr --output DVI-I-1 --mode 1680x1050 --pos 1280x0 --rotate normal --output HDMI-1 --mode 1280x1024 --pos 0x0 --rotate normal This workaround stop working after the update to 13.04, and now i'm looking for a new solution. Has anyone experienced something similarity? xrandr output: Screen 0: minimum 320 x 200, current 2960 x 1050, maximum 8192 x 8192 DVI-I-1 connected 1680x1050+0+0 (normal left inverted right x axis y axis) 433mm x 270mm 1680x1050 60.0*+ 1280x1024 75.0 60.0 1280x960 60.0 1152x864 75.0 1024x768 75.1 72.0 70.1 60.0 832x624 74.6 800x600 72.2 75.0 60.3 56.2 640x480 72.8 75.0 66.7 60.0 720x400 70.1 HDMI-1 connected 1280x1024+1680+0 (normal left inverted right x axis y axis) 376mm x 301mm 1280x1024 60.0*+ 75.0 1152x864 75.0 1024x768 75.1 60.0 800x600 75.0 60.3 640x480 75.0 60.0 720x400 70.1 lshw -c video: *-display Beschreibung: VGA compatible controller Produkt: G96 [GeForce 9500 GS] Hersteller: NVIDIA Corporation Physische ID: 0 Bus-Informationen: pci@0000:01:00.0 Version: a1 Breite: 64 bits Takt: 33MHz Fähigkeiten: pm msi pciexpress vga_controller bus_master cap_list rom Konfiguration: driver=nouveau latency=0 Ressourcen: irq:16 memory:fa000000-faffffff memory:d0000000-dfffffff memory:f8000000-f9ffffff ioport:df00(Größe=128) memory:fb000000-fb07ffff Thanks for your help!

    Read the article

  • Basic multicast network performance problems

    - by davedavedave
    I've been using mpong from 29west's mtools package to get some basic idea of multicast latency across various Cisco switches: 1Gb 2960G, 10Gb 4900M and 10Gb Nexus N5548P. The 1Gb is just for comparison. I have the following results for ~400 runs of mpong on each switch (sending 65536 "ping"-like messages to a receiver which then sends back -- all over multicast). Numbers are latencies measured in microseconds. Switch Average StdDev Min Max 2960 (1Gb) 109.68463 0.092816 109.4328 109.9464 4900M (10Gb) 705.52359 1.607976 703.7693 722.1514 NX 5548(10Gb) 58.563774 0.328242 57.77603 59.32207 The result for 4900M is very surprising. I've tried unicast ping and I see the 4900 has ~10us higher latency than the N5548P (average 73us vs 64us). Iperf (with no attempt to tune it) shows both 10Gb switches give me 9.4Gbps line speed. The two machines are connected to the same switch and we're not doing any multicast routing. OS is RHEL 6. 10Gb NICs are HP 10GbE PCI-E G2 Dual-port NICs (I believe they are rebranded Mellanox cards). The 4900 switch is used in a project with tight access control so I'm waiting for approval before I can access it and check the config. The other two I have full access to configure. I've looked at the Cisco document[2] detailing differences between NX-OS and IOS w.r.t multicast so I've got some ideas to try out but this isn't an area where I have much expertise. Does anyone have any idea what I should be looking at once I get access to the switch? [1] http://docwiki.cisco.com/wiki/Cisco_NX-OS/IOS_Multicast_Comparison

    Read the article

  • Server load high, CPU idle. NFS the cause?

    - by Mech Software
    I am running into a scenario where I'm seeing a high server load (sometimes upwards of 20 or 30) and a very low CPU usage (98% idle). I'm wondering if these wait states are coming as part of an NFS filesystem connection. Here is what I see in VMStat procs -----------memory---------- ---swap-- -----io---- --system-- -----cpu------ r b swpd free buff cache si so bi bo in cs us sy id wa st 2 1 0 1298784 0 0 0 0 16 5 0 9 1 1 97 2 0 0 1 0 1308016 0 0 0 0 0 0 0 3882 4 3 80 13 0 0 1 0 1307960 0 0 0 0 120 0 0 2960 0 0 88 12 0 0 1 0 1295868 0 0 0 0 4 0 0 4235 1 2 84 13 0 6 0 0 1292740 0 0 0 0 0 0 0 5003 1 1 98 0 0 4 0 0 1300860 0 0 0 0 0 120 0 11194 4 3 93 0 0 4 1 0 1304576 0 0 0 0 240 0 0 11259 4 3 88 6 0 3 1 0 1298952 0 0 0 0 0 0 0 9268 7 5 70 19 0 3 1 0 1303740 0 0 0 0 88 8 0 8088 4 3 81 13 0 5 0 0 1304052 0 0 0 0 0 0 0 6348 4 4 93 0 0 0 0 0 1307952 0 0 0 0 0 0 0 7366 5 4 91 0 0 0 0 0 1307744 0 0 0 0 0 0 0 3201 0 0 100 0 0 4 0 0 1294644 0 0 0 0 0 0 0 5514 1 2 97 0 0 3 0 0 1301272 0 0 0 0 0 0 0 11508 4 3 93 0 0 3 0 0 1307788 0 0 0 0 0 0 0 11822 5 3 92 0 0 From what I can tell when the IO goes up the waits go up. Could NFS be the cause here or should I be worried about something else? This is a VPS box on a fiber channel SAN. I'd think the bottleneck wouldn't be the SAN. Comments?

    Read the article

  • Abnormally high amount of Transmit discards reported by Solarwinds for multiple switches

    - by Jared
    I have several 3750X Cisco switches that, according to our Solarwinds NPM, are producing billions of transmit discards per day. I'm not sure why it's reporting these discards. Many of the ports on the 3750X's have 2960's connected to them and are hardcoded as trunk ports. Solarwinds NPM version 10.3 Cisco IOS version 12.2(58)SE2 Total output drops: 29139431: GigabitEthernet1/0/43 is up, line protocol is up (connected) Hardware is Gigabit Ethernet, address is XXXX (bia XXXX) Description: XXXX MTU 1500 bytes, BW 100000 Kbit/sec, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex, 100Mb/s, media type is 10/100/1000BaseTX input flow-control is off, output flow-control is unsupported ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:47, output 00:00:50, output hang never Last clearing of "show interface" counters 1w4d Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 29139431 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 35000 bits/sec, 56 packets/sec 51376 packets input, 9967594 bytes, 0 no buffer Received 51376 broadcasts (51376 multicasts) 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog, 51376 multicast, 0 pause input 0 input packets with dribble condition detected 115672302 packets output, 8673778028 bytes, 0 underruns 0 output errors, 0 collisions, 0 interface resets 0 unknown protocol drops 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier, 0 pause output 0 output buffer failures, 0 output buffers swapped out sh controllers gigabitEthernet 1/0/43 utilization: Receive Bandwidth Percentage Utilization : 0 Transmit Bandwidth Percentage Utilization : 0

    Read the article

  • Set up layer 2 vlan between 2 data centres

    - by user41679
    Hello, Our data centre provider operates 2 sites, and we currently have equipment in one and would like to have equipment in the second. They've told me that they operate a layer 2 vlan between the 2 sites over a 20gbit connection, and that they'd just give me ethernet cable at each end to connect the locations. At the current site, we have Cisco 2960 48TC-L switches, all the machines are on a 192.168.x.x subnet and we have cisco firewalls with which we connect to our internet provider with. My question is what would I need to do to connect the 2 sites? could I just plug the ethernet cables the provide into the cisco switches, and have the same switches the other end? would I need to set up a separate internal network on the other side and connect both through the firewalls? Would the cisco switches need special configuration? We expect to maintain a number of connections between the 2 sites, and each site would have its own internal dns name like dc1.xx.com. Sorry if I'm being vague or haven't included enough information, I've a fairly good knowledge of hardware but we're down a netops guy at the moment and I'd like to get both sites on-line ASAP! Thanks in advance!

    Read the article

  • Issues getting a Cisco WLC 5508 to find AIR-LAP1142N

    - by user95917
    hoping someone can help me with a problem here. I'm attempting to setup a test (loan from Cisco) wireless network. Here's what i've got/done: 5508 Controller - Service Port IP set to 10.74.5.2 /24. Management IP set to 10.74.6.2 /24 with a default gateway of 10.74.6.1. Virtual IP set to 1.1.1.1. Copper SFP in slot 7, CAT5 (known good) going from there to port 1/0/47 on the switch. Green lights on both ends. 2960-S Switch - Vlan1 - 10.74.6.1 /24. dhcp pool 10.74.6.0 /24, default router 10.74.6.1. excluded-address 10.74.6.1, 10.74.6.2. 1/0/4 on the switch is set to switchport mode access and no shut. 1/0/47 on the switch is setup to switchport mode trunk and no shut. 1/0/4 has a CAT5 (known good) cable going from there to the AP. When I do a sh cdp nei from the switch, i can see the AP and Controller listed. When i configure my PC's nic to 10.74.5.5, and plug a cable from my nic to the SP port on the controller i can get on the device via the gui. In there, the only errors/info that show up in the trap are: Link Up: Slot: 0 Port: 7 Controller time base status - Controller is out of sync with the central timebase. I've manually set the time but apparently that's not quite the problem (or at least not the entire problem). When i plug the AP in, i see on the switch console that it grants it power, it sees it connect...but the controller won't see it for some reason. From what i've read you shouldn't have to do anything to the AP as it's managed by the controller...but i'm not sure what setting I'm missing for it to work. The AP light on top is continually cycling green, red, yellow. When I first start it up, it blinks green for 20 or so seconds, then goes to solid green for another 20 seconds or so, then flashes blue, green, red for awhile...but always ends up goinn back to the standard, green, red, yellow. Does anyone see any obvious issues with my setup or have any suggestions as to why i might be having a problem? Thanks for your help!

    Read the article

  • Network Restructure Method for Double-NAT network

    - by Adrian
    Due to a series of poor network design decisions (mostly) made many years ago in order to save a few bucks here and there, I have a network that is decidedly sub-optimally architected. I'm looking for suggestions to improve this less-than-pleasant situation. We're a non-profit with a Linux-based IT department and a limited budget. (Note: None of the Windows equipment we have runs does anything that talks to the Internet nor do we have any Windows admins on staff.) Key points: We have a main office and about 12 remote sites that essentially double NAT their subnets with physically-segregated switches. (No VLANing and limited ability to do so with current switches) These locations have a "DMZ" subnet that are NAT'd on an identically assigned 10.0.0/24 subnet at each site. These subnets cannot talk to DMZs at any other location because we don't route them anywhere except between server and adjacent "firewall". Some of these locations have multiple ISP connections (T1, Cable, and/or DSLs) that we manually route using IP Tools in Linux. These firewalls all run on the (10.0.0/24) network and are mostly "pro-sumer" grade firewalls (Linksys, Netgear, etc.) or ISP-provided DSL modems. Connecting these firewalls (via simple unmanaged switches) is one or more servers that must be publically-accessible. Connected to the main office's 10.0.0/24 subnet are servers for email, tele-commuter VPN, remote office VPN server, primary router to the internal 192.168/24 subnets. These have to be access from specific ISP connections based on traffic type and connection source. All our routing is done manually or with OpenVPN route statements Inter-office traffic goes through the OpenVPN service in the main 'Router' server which has it's own NAT'ing involved. Remote sites only have one server installed at each site and cannot afford multiple servers due to budget constraints. These servers are all LTSP servers several 5-20 terminals. The 192.168.2/24 and 192.168.3/24 subnets are mostly but NOT entirely on Cisco 2960 switches that can do VLAN. The remainder are DLink DGS-1248 switches that I am not sure I trust well enough to use with VLANs. There is also some remaining internal concern about VLANs since only the senior networking staff person understands how it works. All regular internet traffic goes through the CentOS 5 router server which in turns NATs the 192.168/24 subnets to the 10.0.0.0/24 subnets according to the manually-configured routing rules that we use to point outbound traffic to the proper internet connection based on '-host' routing statements. I want to simplify this and ready All Of The Things for ESXi virtualization, including these public-facing services. Is there a no- or low-cost solution that would get rid of the Double-NAT and restore a little sanity to this mess so that my future replacement doesn't hunt me down? Basic Diagram for the main office: These are my goals: Public-facing Servers with interfaces on that middle 10.0.0/24 network to be moved in to 192.168.2/24 subnet on ESXi servers. Get rid of the double NAT and get our entire network on one single subnet. My understanding is that this is something we'll need to do under IPv6 anyway, but I think this mess is standing in the way.

    Read the article

  • Windows 7 explorer always crashes, opens small "Personalized Settings" window

    - by Ian Sellar
    My Windows 7 desktop PC, built by me, started acting very weird in the last couple of days. I use it quite often, about half of the time through TeamViewer. Explorer would crash and restart randomly, almost always through TeamViewer. This made me suspect that TeamViewer was the problem but I have reproduced it with and without TeamViewer several times. The only way I can seem to get the problem not to occur is by booting into Safe Mode. I have used CCleaner and Malwarebytes to make sure it wasn't a registry error or malware causing the problem, and I have tried the fix in the seemly related issue here as well every other fix I have found online including removing security updates KB980408 and KB2926765 as well as using "sfc /scannow" and a bunch of other things I can't remember. More recently when I try to start explorer it is popping up a small window that says "Personalized Settings" on the top, but is completely empty and crashes instantly. The only way I can get it to disappear is to kill the explorer.exe process. I wish I could take a screenshot but I can't seem to open paint or even find the exe. I have tried restarting it, I have tried starting it while the personalized settings window was open. I have come up with two lists of processes the first is the list of active processes when I boot into safe mode and explorer seems to work fine. The second is the list of processes that I can narrow it down to in normal boot and still replicate the problem. There is one process that I can't seem to close. NisSrv.exe which is describes as "Microsoft Network Realtime Inspection Service". When I try to close the process NisSrv.exe it says "The operation could not be completed. Access is denied." When I try to close the related service it gives the same message. Image Name PID Session Name Session# Mem Usage ========================= ======== ================ =========== ============ System Idle Process 0 Services 0 24 K System 4 Services 0 2,660 K smss.exe 304 Services 0 1,196 K csrss.exe 408 Services 0 4,156 K wininit.exe 444 Services 0 4,608 K csrss.exe 452 Console 1 8,700 K services.exe 492 Services 0 7,700 K winlogon.exe 524 Console 1 5,756 K lsass.exe 536 Services 0 10,644 K lsm.exe 544 Services 0 4,316 K svchost.exe 652 Services 0 8,976 K MsMpEng.exe 804 Services 0 40,696 K explorer.exe 1332 Console 1 85,220 K ctfmon.exe 1376 Console 1 3,680 K dllhost.exe 1624 Console 1 8,656 K chrome.exe 1408 Console 1 98,504 K WmiPrvSE.exe 2352 Services 0 6,472 K chrome.exe 1744 Console 1 65,116 K taskmgr.exe 372 Console 1 14,948 K cmd.exe 2776 Console 1 2,960 K conhost.exe 1816 Console 1 3,580 K tasklist.exe 2308 Console 1 5,868 K And the list of processes I have narrowed it down to. Image Name PID Session Name Session# Mem Usage ========================= ======== ================ =========== ============ System Idle Process 0 Services 0 24 K System 4 Services 0 2,808 K smss.exe 316 Services 0 1,216 K csrss.exe 484 Services 0 4,532 K wininit.exe 596 Services 0 4,604 K csrss.exe 604 Console 1 23,676 K services.exe 652 Services 0 11,344 K lsass.exe 668 Services 0 12,692 K lsm.exe 676 Services 0 4,464 K MsMpEng.exe 972 Services 0 68,436 K winlogon.exe 168 Console 1 7,784 K svchost.exe 496 Services 0 19,140 K NisSrv.exe 3176 Services 0 808 K svchost.exe 1684 Services 0 11,260 K taskmgr.exe 4524 Console 1 20,696 K cmd.exe 4764 Console 1 7,224 K conhost.exe 4772 Console 1 6,916 K sublime_text.exe 2340 Console 1 45,012 K dllhost.exe 4476 Console 1 8,736 K tasklist.exe 3796 Console 1 5,768 K WmiPrvSE.exe 1768 Services 0 6,344 K Here is the event data xml from event viewer for the error I am getting. <EventData> <Data>explorer.exe</Data> <Data>6.1.7601.17567</Data> <Data>4d672ee4</Data> <Data>vrfcore.dll</Data> <Data>6.3.9600.16384</Data> <Data>5215f8f5</Data> <Data>80000003</Data> <Data>0000000000003a00</Data> <Data>12e4</Data> <Data>01cfb84fa70f89dc</Data> <Data>C:\Windows\system32\explorer.exe</Data> <Data>C:\Windows\SYSTEM32\vrfcore.dll</Data> <Data>e5957093-2442-11e4-9f8a-94de806ed9cb</Data> </EventData> I was looking through the eventvwr log again and I found this, possibly related <EventData> <Data>runonce.exe</Data> <Data>6.1.7601.17514</Data> <Data>4ce7a253</Data> <Data>MSVCR100.dll</Data> <Data>10.0.40219.325</Data> <Data>4df2bcac</Data> <Data>c0000005</Data> <Data>000000000003c145</Data> <Data>670</Data> <Data>01cfb8dabbd85942</Data> <Data>C:\Windows\system32\runonce.exe</Data> <Data>C:\Windows\system32\MSVCR100.dll</Data> <Data>fa6f82b9-24cd-11e4-80a8-94de806ed9cb</Data> </EventData> And the general error details Faulting application name: Explorer.EXE, version: 6.1.7601.17567, time stamp: 0x4d672ee4 Faulting module name: vrfcore.dll, version: 6.3.9600.16384, time stamp: 0x5215f8f5 Exception code: 0x80000003 Fault offset: 0x0000000000003a00 Faulting process id: 0xc38 Faulting application start time: 0x01cfb84e5e852c5f Faulting application path: C:\Windows\Explorer.EXE Faulting module path: C:\Windows\SYSTEM32\vrfcore.dll Report Id: 9dc19e6d-2441-11e4-9f8a-94de806ed9cb Another probably unrelated error that I seem to be getting pretty often. Event filter with query "SELECT * FROM __InstanceModificationEvent WITHIN 60 WHERE TargetInstance ISA "Win32_Processor" AND TargetInstance.LoadPercentage > 99" could not be reactivated in namespace "//./root/CIMV2" because of error 0x80041003. Events cannot be delivered through this filter until the problem is corrected. My explorer tab in Autoruns seen below along with the error when I try to uncheck something. I should add that I seem to be able to disable shell extensions with ShellExView but I still can't get explorer to start correctly. EXPLORER SHELL UPDATE - See screenshot below I can access the explorer right click menu through a file manager I downloaded called NexusFile, but still no luck starting explorer. Another round of errors that I am getting regarding Windows Search Service The search service has detected corrupted data files in the index {id=4700}. The service will attempt to automatically correct this problem by rebuilding the index. Details: The content index catalog is corrupt. (HRESULT : 0xc0041801) (0xc0041801) followed by The Windows Search Service is being stopped because there is a problem with the indexer: The catalog is corrupt. Details: The content index catalog is corrupt. (HRESULT : 0xc0041801) (0xc0041801 and The plug-in in <Search.JetPropStore> cannot be initialized. Context: Windows Application, SystemIndex Catalog Details: The content index catalog is corrupt. (HRESULT : 0xc0041801) (0xc0041801) and The gatherer object cannot be initialized. Context: Windows Application, SystemIndex Catalog Details: The content index catalog is corrupt. (HRESULT : 0xc0041801) (0xc0041801) and The Windows Search Service cannot load the property store information. Context: Windows Application, SystemIndex Catalog Details: The content index database is corrupt. (HRESULT : 0xc0041800) (0xc0041800) WER Log http://pastebin.com/WXKGDT4Q I'll add information as I remember it or people request it.

    Read the article

1