Search Results

Search found 102 results on 5 pages for 'atx'.

facebook twitter digg google delicious technorati stumbleupon myspace wordpress linkedin gmail igoogle windows live tumblr viadeo yahoo buzz yahoo mail yahoo bookmarks favorites email print

Page 1/5 | 1 2 3 4 5  | Next Page >

  • ATX power: 20 or 24 pins?

    - by djechelon
    What is the difference between 20-pins ATX power cables and 24-pins ATX power cables for motherboard? I see that Cooler Master Silent Pro PSU has an extensible plug, showing 20 pins + 4 pluggable pins. Since I'm having troubles with my motherboard, which has 24 pins, I tried to connect only the first 20 and the system booted up fine. I'm curious: can any ATX motherboard run with 20-pins power? Will I simply experience lower performance?

    Read the article

  • Is it possible (and safe/reliable/non-damaging) to use a 20-pin ATX PSU with a 24-pin ATX motherboar

    - by Legooolas
    I have a reasonably-decent old 20-pin PSU which I want to use on a newer 24-pin ATX motherboard. I see that the ATX page on wikipedia mentions that 24-pin ATX is backward-compatible, and I can find 20-to-24 pin adapters to buy for a couple of dollars/pounds at lots of places, but I can't find any mention of restrictions on the use of these. Will this work on any motherboard, or is it a per-motherboard compatibility question? Are there any other restrictions like the level of power available (and hence the additional 4 pins with +12, +5 and +3.3V lines which are already on other pins)?

    Read the article

  • Is the 4pin atx power plug required?

    - by rockinthesixstring
    I know the answer is probably a resounding YES, but I just wanted to double check. I just purchased a new chassis for my PC and now my 4pin cpu power plug doesn't reach. I'm wondering if the 4 pins are required for operation, or can I get by for the weekend without it until I can go get an extension?

    Read the article

  • Is the 4pin atx power plug required [closed]

    - by rockinthesixstring
    I know the answer is probably a resounding YES, but I just wanted to double check. I just purchased a new chassis for my PC and now my 4pin cpu power plug doesn't reach. I'm wondering if the 4 pins are required for operation, or can I get by for the weekend without it until I can go get an extension? EDIT: Looks like it is mandatory with my Mobo. I tried to post without it and i just got a blank screen. Looks like I'm getting a new adapter asap.

    Read the article

  • Understanding why a 450W power supply is destroying my ATX motherboards but not mATX

    - by T. Webster
    Maybe I'm missing something really obvious here, but after going through 3 new motherboards in trying to build my new machine, I'm finally certain that the 450W power supply I bought has been destroying them. It seems like it should be simple: just connect the connectors where they fit and switch the thing on. But today after hooking it to my ASUS Sabertooth 990FX TUF Series Motherboard and switching it on, I could see and smell the smoke coming out of the motherboard. What I don't get is why I can hook this same 450W power supply up to my mATX motherboard and not run into the same problem. What am I missing here? Where on the box or manual is this? (I have 8x2 GB RAM, AMD FX-4100 3.6GHz CPU, 1 512MB ATI graphics card, 1 WD 7200 RPM SATA hard drive. )

    Read the article

  • 2 "P4" power connectors *AND* an 8 pin EPS connector -- all necessary?

    - by chris
    I recently bought an Arima SW350 motherboard. It supports 16 ddr simms as well as 2 opteron 2xx CPUs, so I imagine it may have pretty heavy power requirements... It has a 24 pin ATX power connector, 2 4 pin "P4" power connectors, and an 8 pin EPS power connector. My supermicro power supply has a 24 pin ATX connector and the EPS connector, and one P4 connector. Can I safely run this thing with only one P4 connector plugged in? Can I safely get a "hard disk to P4" adapter and use that to power the other P4 connector on the motherboard? Do I just need a new power supply? The board's documentation is pretty thin on the topic.

    Read the article

  • Building computer: Casing for peripheral sockets is a pain!

    - by burnt1ce
    I have a casing the covers the spacing between the peripheral socket which is standard to have when you buy a motherboard. My problem with these covers is that they have spokes that pushes the motherboard away so the sockets don't even come out of the covers. This also misaligns the screws on my atx motherboard with the holes in my computer case. I usually break these spokes so that i can align my motherboard correctly. Why the heck do motherboard manufacture put spokes on these covers? am i using them wrong? UPDATE Here's an image that i found that shows the plastic casing. http://z.about.com/d/pcsupport/1/5/m/-/-/-/tour%5Fexternal.jpg You can even see the indentation that makes the spokes that pushes the motherboard inwards.

    Read the article

  • Methods of cooling with no more room in case?

    - by Wesley
    Hi all, I've got an HP DC7100 and an HP m8530f. The DC7100 is a small form factor desktop while the m8530f has a mATX board with lots of extra features like front I/O and HP Personal Media Drive bay. Both of these have very little space (especially the DC7100) and don't have any other places to mount fans. What other possible ways of cooling are there, if there isn't much space left inside the case? Thanks in advance.

    Read the article

  • Do 24pin motherboard wires have to be in a certain order?

    - by jasondavis
    I am wanting to sleeve all the wires in my new PC. On my 24pin motherboard connection cable, I must remove the end plastic connector piece from all the wires to sleeve them all individually. I have a couple questions about this cable though. 1) When I put all the wires back into the connector, must they be in the same order they are in now? 2) I have taken a low quality iphone photo below so you cannot see to well, but in a couple spots I marked with arrows, there is actually 2 wires going into a single slot. I am not sure what to do with those, do all 24pin motherboard connectors have some slots where 2 wires go in like that?

    Read the article

  • I/O ports vs case holes

    - by David Oneill
    I'm in the midst of building a new desktop (first time building my own). I bought MSI NF750-G55 AM3 NVIDIA nForce 750a SLI HDMI ATX motherboard, and HEC 6C28BS Black / Silver Steel ATX Mid Tower case. When they both arrived, I realized that the I/O panel on the case doesn't have the same holes that the motherboard needs. So my two questions are: 1) What should I have done? Both claim to be ATX. Do I just need to look more carefully at the pictures? 2) What should I do now? Can I just remove the whole panel (leaving empty spaces between and around the different ports? Specifically, will it cause problems to do this? (I'm looking for advice about question 1, but will accept based on question 2)

    Read the article

  • Server freezes while installing Redhat Enterprise Linux Server 6

    - by eisaacson
    We've tried both the first options Install or upgrade an existing system Install system with basic video driver When trying option #1, it gets to a screen that has a solid cursor about halfway down, then freezes. When trying option #2, it freezes at the point where it says: Waiting for hardware to initialize... Of course, we bought the unsupported version and haven't found anything to help us so far. Here are the specs to the server in the original post: ASUS P8Z68-M Pro LGA 1155 Intel Z68 HDMI SATA 6Gb/s USB 3.0 Micro ATX Intel Motherboard with UEFI BIOS RAIDMAX Reiter ATX-305WBP Black Steel / Plastic ATX Mid Tower Computer Case 450W Power Supply Intel Core i7-2600 Sandy Bridge 3.4GHz (3.8GHz Turbo Boost) LGA 1155 95W Quad-Core Desktop Processor Intel HD Graphics 2000 BX80623I72600 16GB Ram OCZ Agility 3 SSD 120GB From some of the posts out there could the UEFI Bios or the Sandy Bridge processor be a culprit here? We just tried the DVD on a different computer and it got past that point with ease. It's a standard Dell build compared to our custom machine. Could it be having difficulty recognizing drivers? How do we get past that?

    Read the article

  • I can't get my PC to start up by a normal way.

    - by ssice
    I couldn't write a more accurate title. I am just unable to start the computer by pressing the Power On button. I checked the Power Supply and it seems to give good voltage values in every pin. And this is not a BIOS malfunction because of bad overclocking or anything that may come to your mind. And I will tell you why. It happens that EPS (or any ATX-based) power supply has the ability to be powered-on by the Motherboard by jumping the 13th pin of the 24-pin-ATX-connector to COM/GND. I did it, after pushing the power on button (without any visual response) and, pwhaa! The machine turned on. I was able to read (and even write, if I wanted) BIOS values and then start any OS installed. Machine starts, so it's not any kind of misconfiguration. It seems some hardware related. I am able to power the machine on only if I already pushed the power on button. Though pushing it without jumping the 13th pin to ground for a second does not power the machine. Of course, jumping the pin without pushing the power on button does not tell the motherboard anything, so the computer would not start up either. It's as if the logic that connects the power button with the 13th pin derivation to GND was unable to be activated. What can be the issue? How can I solve it? My configuration is as follows: CPU: AMD Phenom 9850 X4 Black Edition MB: ASUS Formula II AM2 RAM: 2x2GB Corsair Dominator 5-5-5-15 2T @ 1066MHz DDR2 Tested also with only 1 module GPU: 2x XFX nVIDIA GeForce 9600 GT XxX Alpha Dog Edition @ Core: 540Mhz [SLi] Power Supply: Xilence 700W (ATX 12V 2.3 / EPS 12V 2.92 compatible) PS: I know the machine is like 2 years old. I hardly use it now, but my parents do.

    Read the article

  • Computer does not boot, often

    - by tam
    I've ran into a issue with my computer that it does no longer reach POST, but simply powers on for a fraction of a second and powers off. But this is not always, some times it boots just normally and it works as it should, no issues with not enough power or anything. But as soon as I turn it of, I can not turn it back on, but then again at some random point it just powers up again, and resumes normal operation. If I disconnect the 8pin ATX connector from the motherboard, it powers up, fans and disks spinning normally until I power it off again. So this problem only happens when ATX is connected, which seems odd, I normally always saw this kind of an error if ATX was not connected, but here it's the exact opposite. It also does not emit any sound on the buzzer, except the normal beep, when it powers up normally. I have already tried: Remove graphics card Remove one and/or all RAM sticks Disconnect everything non-essential, even hard drives Clear CMOS I have not yet tried to remove all components and tried to boot everything outside of the case, because I did not have the time to disassemble and bleed the water loop. However, I can confirm that nothing is stuck underneath the motherboard, not is any of those brass raisers touching the board where it should not. Specs: Gigabyte GA-970A-UD3 AMD FX6300 ATI HD7850 I think this should be enough for this issue.

    Read the article

  • What components should I upgrade to squeeze more life of my pc? [on hold]

    - by Jared
    Hi my current specs are CPU: Intel Core i5 750 2.66 GHz, Socket 1156 Motherboard: Asus P7P55 LX Motherboard, Socket 1156, 4xDIMM DDR3, 2xPCIe-16, 3xPCI, 2xPCIe-1, 14xUSB2, Audio, 1xATA, 6xSATA, RAID, ATX HDD: Seagate Barracuda 7200.11 ST31500341AS Hard Disk Drive, 1500GB, 7200rpm, 32MB Cache, SATA-2 RAM: G.Skill Ripjaw F3-12800CL8D-4GBRM, 2x2GB, DDR3-1600, PC3-12800, CL8, DIMM Video: MSI Radeon 5850 R5850-PM2D1G Video Card, 1024MB, DDR5, PCIe-16, DVI, CrossFire, HDMI PSU: Vantec ION2, 620W ATX PSU, SLI Ready, Black Firstly I know it badly needs an SSD, for which I'm thinking of the Samsung 250gb 840 EVO series. The ram could do with another 4GB, for which I am thinking of replacing the 2x2GB for 2x4GB of the same type. My video card is struggling with the latest releases, so vitally should I ditch the video card and go for something newer (ATI 7850, GTX 660?) or try and get another 5850 for crossfire support? Bearing in mind 5850's are sort of hard to come buy now as they are not stocked in shops usually, which means they have to be bought second hand.

    Read the article

  • "No root file system is defined"

    - by user169670
    Have recently installed Ubuntu 12.04.2 LTS by USB on my newly built custom pc and I have run into a problem during installation with the error saying "No root file system is defined." My pc speculations: AMD Phenom x4 955 Black Edition ASRock 960GM/U3S3 FX Micro ATX AM3+ Motherboard Mushkin Redline 8GB (2x4GB) DDR3-1866 Memory Seagate Barracuda 1.5TB 3.5" 7200RPM Internal Hard Drive XFX Radeon HD 7850 1GB Video Card XFX 550W 80 PLUS Bronze Certified ATX12V / EPS12V Power Supply Everything is new.

    Read the article

  • Building new computer, turns on, but no post

    - by addybojangles
    Pardon my ignorance here, finally decided to put together a computer and egads. I purchased a new motherboard, power supply, processor, video card and memory. ASUS M4A79XTD EVO AM3 AMD 790X ATX AMD Motherboard OCZ Fatal1ty OCZ550FTY 550W ATX12V v2.2 / EPS12V SLI Ready 80 PLUS Certified Modular Active PFC Power Supply AMD Phenom II X4 965 Black Edition Deneb 3.4GHz 4 x 512KB L2 Cache 6MB L3 Cache Socket AM3 125W Quad-Core Processor XFX HD-577A-ZNFC Radeon HD 5770 (Juniper XT) 1GB 128-bit GDDR5 PCI Express 2.0 x16 HDCP Ready CrossFireX Support Video Card G.SKILL 4GB (2 x 2GB) 240-Pin DDR3 SDRAM DDR3 1600 (PC3 12800) Dual Channel Kit Desktop Memory Model F3-12800CL9D-4GBNQ (originally had links for you guys, but I lack the rep, sorry!!) And I've got it all in the tower. I put in power supply, installed processor on motherboard, installed heatsink, put in ram, and I am using an older IDE hard disk. When I start the computer, the monitor tells me "check signal cable." As far as I can tell, the heatsink on the processor is spinning, the power supply is on (obviously), and the green LED on the motherboard is on. I originally only had the bigger output plugged in to the motherboard (what I saw in a YouTube vid as well as the mobo instructions), but after doing some research, it said plug in the other ATX power supply. Which I did. And trying to power the computer results in nothing. No beeps on startup, no post, anyone have any ideas? Your ideas and help is greatly appreciated.

    Read the article

  • What parts should I get for an ASRock x58 Extreme motherboard

    - by Brad Gilbert
    I just received an ASRock x58 Extreme motherboard, for my post on this question. It was a 2009 Tom's Hardware recommended buy. It is a Core i7 motherboard, with an X58 Express Chipset. It uses DDR3 RAM. What I want to know is, what parts should I get to finish it off. I'm looking for some good bargains, because of a lack of funds. The most taxing game I will probably play on it is OpenTTD. The only parts I currently have that are compatible: A Dynex 400W power supply. It appears to be an ATX 2.1 power supply, with the addition of a -5 rail. Apparently designed to be compatible with most ATX-style motherboards. Several PCI add-in cards. Mostly 10/100 Network cards Some sound cards Some video cards with a VGA connector Plenty of PATA drives. 8 GB - 80 GB Hard-drives A dozen or-so CD-ROM drives, only a handful of them are CD-RW drives. One DVD-ROM drive I have one LCD, with a 15 pin VGA connector, which I salvaged from the dump. The only thing wrong with it was some dead capacitors. It also has a stuck pixel.

    Read the article

  • Windows 7 Won't Boot

    - by Vie
    I recently built a new computer, my fifth one. ASUS Maximus III Formula LGA 1156 Intel P55 ATX Motherboard EVGA 01G-P3-1452-TR GeForce GTS 450 Superclocked 1GB 128-bit GDDR5 PCI Express 2.0 x16 HDCP Video Card COOLMAX RM-1000B 1000W ATX psu Intel Core i7-875K lynnfield 2.93GHz LGA 1156 95w Quad-Core unlocked processor G.SKILL Ripjaws Series 16 (4x4GB) 240-Pin DDR3 SDRAM DDR3 1333 (PC3 10666) memory WD VelociRaptor WD3000GLFS 300gb 10000 RPM SATA 3.0Gb/s Hard Drive Sony Optiarc CD/DVD Burner model AD-7261S-0B LightScribe Windows 7 Home Premium 64-bit It gets hung up on the starting windows screen. When I went to install the OS it did the same thing wouldn't go past the windows logo, so I put the new HDD into my old computer and installed windows 7 thinking it was just an installer error. Put the fully installed HDD back into my new machine and it still gets stuck on the starting windows screen. I've tried most everything I've looked up. Disabled USB, Disabled Turbo Boost, Disabled everything that wasn't essential(just about every configuration I can think of), took it apart and put it back together, took all the ram out save one 4g stick(wouldn't even boot when I did this), did a memory scan which came back successful, I don't know what could be wrong. Only thing I can think of is a compatibility issue somewhere, but I've ran over it again and again and I don't know where there would be an issue like that. Need Backup! .<

    Read the article

  • my cpu won't start. all fan were spinning for a second then nothing happen

    - by Tommy
    I need help about this.. I'm from Malaysia.. Back then my cpu is all okay..and it's 4 year old.. I think this question is answered before but i'm still don't understand.. when i plugged my cpu..turn it on and all of the fan (graphic card, mobo fan and PSU fan) were spinning just for a second than nothing happen.. I don't know if it is because of the PSU or my mobo.. I sent my cpu to the shop and they said it must be the mobo.. They tell me to change my mobo and PSU also..and it cost over 100 buck (rm300 in Malaysia). and i'm real 'dry' right now. My whole data is inside the HDD. School projects, photos, games, and many..I really-really need my cpu back alive.. My mobo is MSI MS-7529 with dual core chips. My PSU is ATX-480W. the PC store guy said i need to change to new ASUS mobo if I want. I dont know what type it is but Then he tell me to change my PSU also because he don't think my old PSU (ATX-480W) ain't compatible to the new mobo.. I was very need a help from you techie guys.. sorry for my terrible English..

    Read the article

  • Cocoa Touch: Creating and Adding Custom View

    - by Jason
    I create a custom view in cocoa touch that is superclassed by UIView and in my main controller I initialize it and then add it as a subview to the main view, but when I add it to the main view it calls my initializer method again and causes an infinite loop. Am I going about creating my custom view wrong? Here is the mainView (void)loadView { UIImage *tempImage = [UIImage imageNamed: @"image1.jpg"]; CustomImageContainer *testImage = [[CustomImageContainer alloc] initWithImage: tempImage andLabel: @"test image" onTop: true atX: 10 atY: 10]; [self.view addSubview: testImage]; } and the CustomImageContainer -(CustomImageContainer *) initWithImage: (UIImage *)imageToAdd andLabel: (NSString *)text onTop: (BOOL) top atX: (int) x_cord atY: (int) y_cord{ UIImageView *imageview_to_add = [[UIImageView alloc] initWithImage: imageToAdd]; imageview_to_add.frame = CGRectMake(0, 0, imageToAdd.size.width, imageToAdd.size.height); UILabel *label_to_add = [[UILabel alloc] init]; label_to_add.text = text; label_to_add.alpha = 50; label_to_add.backgroundColor = [UIColor blackColor]; label_to_add.textColor = [UIColor whiteColor]; [self addSubview: imageview_to_add]; self.frame = CGRectMake(x_cord, y_cord, imageToAdd.size.width, imageToAdd.size.height); if (top) { label_to_add.frame = CGRectMake(0, 0, imageview_to_add.frame.size.width, imageview_to_add.frame.size.height); //[self addSubview: label_to_add]; } else { label_to_add.frame = CGRectMake(0,.2 * imageview_to_add.frame.size.height, imageview_to_add.frame.size.width, imageview_to_add.frame.size.height); } [self addSubview: label_to_add]; [super init]; return self; }

    Read the article

  • Passive cooling a Pentium III

    - by gravyface
    Looking at running pfSense on an old P3 866Mhz. It's noisy, I'd like to passively-cool it, downclocking is ok as this is more than enough horsepower for my needs at home. Obviously I'm cheaping out here: wonder if I bigger heatsink will do and how much case flow I need (it's in a standard mid-tower ATX case).

    Read the article

facebook twitter digg google delicious technorati stumbleupon myspace wordpress linkedin gmail igoogle windows live tumblr viadeo yahoo buzz yahoo mail yahoo bookmarks favorites email print

1 2 3 4 5  | Next Page >