Search Results

Search found 24 results on 1 pages for 'brigham'.

Page 1/1 | 1 

• Splwow64 with TS Easy Print

  - by Tim Brigham

  I have an application (Sage MIP Fund Accounting) which exports data to Excel. In this process it uses an internal print driver. Since we upgraded from 2008 to 2008 R2 this export process causes system hangs. This has been isolated down to the splwow64 executable hanging while the Excel document is building. If I kill the spwow64 executable things function properly (I just can't print it once completed). This only occurs while using printer redirection using the Remote Desktop Easy Print function - if I pull the printer redirection things work exactly as expected. I've spent the last couple hours looking at hotfixes or driver upgrades since this appears to be a problem specifically with how the Remote Desktop Easy Printer printer is functioning. Is anyone aware of a hotfix which would be applicable in this situation? I don't want to grab every hotfix for redirected printing and start throwing them out there.

  Read the article

• HP to Cisco spanning tree root flapping

  - by Tim Brigham

  Per a recent question I recently configured both my HP (2x 2900) and Cisco (1x 3750) hardware to use MSTP for interoperability. I thought this was functional until I applied the change to the third device (HP switch 1 below) at which time the spanning tree root started flapping causing performance issues (5% packet loss) between my two HP switches. I'm not sure why. HP Switch 1 A4 connected to Cisco 1/0/1. HP Switch 2 B2 connected to Cisco 2/0/1. HP Switch 1 A2 connected to HP Switch 2 A1. I'd prefer the Cisco stack to act as the root. EDIT: There is one specific line - 'spanning-tree 1 path-cost 500000' in the HP switch 2 that I didn't add and was preexisting. I'm not sure if it could have the kind of impact that I'm describing. I'm more a security and monitoring guy then networking. EDIT 2: I'm starting to believe the problem lies in the fact that the value for my MST 0 instance on the Cisco is still at the default 32768. I worked up a diagram: This is based on every show command I could find for STP. I'll make this change after hours and see if it helps. Cisco 3750 Config: version 12.2 spanning-tree mode mst spanning-tree extend system-id spanning-tree mst configuration name mstp revision 1 instance 1 vlan 1, 40, 70, 100, 250 spanning-tree mst 1 priority 0 vlan internal allocation policy ascending interface TenGigabitEthernet1/1/1 switchport trunk encapsulation dot1q switchport mode trunk ! interface TenGigabitEthernet2/1/1 switchport trunk encapsulation dot1q switchport mode trunk ! interface Vlan1 no ip address ! interface Vlan100 ip address 192.168.100.253 255.255.255.0 ! Cisco 3750 show spanning tree: show spanning-tree MST0 Spanning tree enabled protocol mstp Root ID Priority 32768 Address 0004.ea84.5f80 Cost 200000 Port 53 (TenGigabitEthernet1/1/1) Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec Bridge ID Priority 32768 (priority 32768 sys-id-ext 0) Address a44c.11a6.7c80 Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec Interface Role Sts Cost Prio.Nbr Type ------------------- ---- --- --------- -------- -------------------------------- Te1/1/1 Root FWD 2000 128.53 P2p MST1 Spanning tree enabled protocol mstp Root ID Priority 1 Address a44c.11a6.7c80 This bridge is the root Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec Bridge ID Priority 1 (priority 0 sys-id-ext 1) Address a44c.11a6.7c80 Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec Interface Role Sts Cost Prio.Nbr Type ------------------- ---- --- --------- -------- -------------------------------- Te1/1/1 Desg FWD 2000 128.53 P2p Cisco 3750 show logging: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to down %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan100, changed state to down %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan100, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to down %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to up HP Switch 1: ; J9049A Configuration Editor; Created on release #T.13.71 vlan 1 name "DEFAULT_VLAN" untagged 1-8,10,13-16,18-23,A1-A4 ip address 100.100.100.17 255.255.255.0 no untagged 9,11-12,17,24 exit vlan 100 name "192.168.100" untagged 9,11-12,17,24 tagged 1-8,10,13-16,18-23,A1-A4 no ip address exit vlan 21 name "Users_2" tagged 1,A1-A4 no ip address exit vlan 40 name "Cafe" tagged 1,4,7,A1-A4 no ip address exit vlan 250 name "Firewall" tagged 1,4,7,A1-A4 no ip address exit vlan 70 name "DMZ" tagged 1,4,7-8,13,A1-A4 no ip address exit spanning-tree spanning-tree config-name "mstp" spanning-tree config-revision 1 spanning-tree instance 1 vlan 1 40 70 100 250 password manager password operator HP Switch 1 show spanning tree: show spanning-tree Multiple Spanning Tree (MST) Information STP Enabled : Yes Force Version : MSTP-operation IST Mapped VLANs : 2-39,41-69,71-99,101-249,251-4094 Switch MAC Address : 0021f7-126580 Switch Priority : 32768 Max Age : 20 Max Hops : 20 Forward Delay : 15 Topology Change Count : 363,490 Time Since Last Change : 14 hours CST Root MAC Address : 0004ea-845f80 CST Root Priority : 32768 CST Root Path Cost : 200000 CST Root Port : 1 IST Regional Root MAC Address : 0021f7-126580 IST Regional Root Priority : 32768 IST Regional Root Path Cost : 0 IST Remaining Hops : 20 Root Guard Ports : TCN Guard Ports : BPDU Protected Ports : BPDU Filtered Ports : PVST Protected Ports : PVST Filtered Ports : | Prio | Designated Hello Port Type | Cost rity State | Bridge Time PtP Edge ----- --------- + --------- ---- ---------- + ------------- ---- --- ---- A1 | Auto 128 Disabled | A2 10GbE-CX4 | 2000 128 Forwarding | 0021f7-126580 2 Yes No A3 10GbE-CX4 | Auto 128 Disabled | A4 10GbE-SR | Auto 128 Disabled | HP Switch 1 Logging: I removed the date / time fields since they are inaccurate (no NTP configured on these switches) 00839 stp: MSTI 1 Root changed from 0:a44c11-a67c80 to 32768:0021f7-126580 00839 stp: MSTI 1 Root changed from 32768:0021f7-126580 to 0:a44c11-a67c80 00842 stp: MSTI 1 starved for an MSTI Msg Rx on port A4 from 0:a44c11-a67c80 00839 stp: MSTI 1 Root changed from 0:a44c11-a67c80 to 32768:0021f7-126580 00839 stp: MSTI 1 Root changed from 32768:0021f7-126580 to 0:a44c11-a67c80 00839 stp: MSTI 1 Root changed from 0:a44c11-a67c80 to ... HP Switch 2 Configuration: ; J9146A Configuration Editor; Created on release #W.14.49 vlan 1 name "DEFAULT_VLAN" untagged 1,3-17,21-24,A1-A2,B2 ip address 100.100.100.36 255.255.255.0 no untagged 2,18-20,B1 exit vlan 100 name "192.168.100" untagged 2,18-20 tagged 1,3-17,21-24,A1-A2,B1-B2 no ip address exit vlan 21 name "Users_2" tagged 1,A1-A2,B2 no ip address exit vlan 40 name "Cafe" tagged 1,13-14,16,A1-A2,B2 no ip address exit vlan 250 name "Firewall" tagged 1,13-14,16,A1-A2,B2 no ip address exit vlan 70 name "DMZ" tagged 1,13-14,16,A1-A2,B2 no ip address exit logging 192.168.100.18 spanning-tree spanning-tree 1 path-cost 500000 spanning-tree config-name "mstp" spanning-tree config-revision 1 spanning-tree instance 1 vlan 1 40 70 100 250 HP Switch 2 Spanning Tree: show spanning-tree Multiple Spanning Tree (MST) Information STP Enabled : Yes Force Version : MSTP-operation IST Mapped VLANs : 2-39,41-69,71-99,101-249,251-4094 Switch MAC Address : 0024a8-cd6000 Switch Priority : 32768 Max Age : 20 Max Hops : 20 Forward Delay : 15 Topology Change Count : 21,793 Time Since Last Change : 14 hours CST Root MAC Address : 0004ea-845f80 CST Root Priority : 32768 CST Root Path Cost : 200000 CST Root Port : A1 IST Regional Root MAC Address : 0021f7-126580 IST Regional Root Priority : 32768 IST Regional Root Path Cost : 2000 IST Remaining Hops : 19 Root Guard Ports : TCN Guard Ports : BPDU Protected Ports : BPDU Filtered Ports : PVST Protected Ports : PVST Filtered Ports : | Prio | Designated Hello Port Type | Cost rity State | Bridge Time PtP Edge ----- --------- + --------- ---- ---------- + ------------- ---- --- ---- A1 10GbE-CX4 | 2000 128 Forwarding | 0021f7-126580 2 Yes No A2 10GbE-CX4 | Auto 128 Disabled | B1 SFP+SR | 2000 128 Forwarding | 0024a8-cd6000 2 Yes No B2 | Auto 128 Disabled | HP Switch 2 Logging: I removed the date / time fields since they are inaccurate (no NTP configured on these switches) 00839 stp: CST Root changed from 32768:0021f7-126580 to 32768:0004ea-845f80 00839 stp: IST Root changed from 32768:0021f7-126580 to 32768:0024a8-cd6000 00839 stp: CST Root changed from 32768:0004ea-845f80 to 32768:0024a8-cd6000 00839 stp: CST Root changed from 32768:0024a8-cd6000 to 32768:0004ea-845f80 00839 stp: CST Root changed from 32768:0004ea-845f80 to 32768:0024a8-cd6000 00435 ports: port B1 is Blocked by STP 00839 stp: CST Root changed from 32768:0024a8-cd6000 to 32768:0021f7-126580 00839 stp: IST Root changed from 32768:0024a8-cd6000 to 32768:0021f7-126580 00839 stp: CST Root changed from 32768:0021f7-126580 to 32768:0004ea-845f80

  Read the article

• Configuring service restart with 'restart service after' parameter

  - by Tim Brigham

  It appears that sc.exe isn't capable of setting the 'restart service after' parameter and powershell isn't capable of setting up service restarts at all. My intended configuration is failure1/restart failure2/restart failure3/nothing with a five minute counter between each restart. The five minute timer is extremely important. Is there anything else I can look at other than some registry hackery configure this?

  Read the article

• Performance associated with storing millions of files on NTFS

  - by Tim Brigham

  Does anyone have a method / formula, etc that I could use - hopefully based on both current and projected numbers of files - to project the 'right' length of the split and the number of nested folders? Please note that although similar it isn't quite the same as Storing a million images in the filesystem. I'm looking for a way to help make the theories outlined more generic. Assumptions I have 'some' initial number of files. This number would be arbitrary but large. Say 500k to 10m+. I have considered the underlying physical hardware disk IO requirements that would be necessary to support such an endeavor. Put another way As time progresses this store will grow. I want to have the best balance of current performance and as my needs increase. Say I double or triple my storage. I need to be able to address both current needs and projected future growth. I need to both plan ahead and not sacrifice too much of current performance. What I've come up with I'm already thinking about using a hash split every so many characters to split things out across multiple directories and keeping the trees even, very similar as outlined in the comments in the question above. It also avoids duplicate files, which would be critical over time. I'm sure that the initial folder structure would be different based on what I've outlined, and depending on the initial scale. As far as I can figure there isn't a one size fits all solution here. It would be horrendously time intensive to work something out experimentally.

  Read the article

• Driver problems with rerunning WIM capture

  - by Tim Brigham

  How do I handle driver problems associated with creating a new WIM file using a previously created image as a base? I am using a custom MDT image which installs Windows 7, Office 2010, etc which was created from a previously deployed base image of Windows 7 + SP 1 + updates. When the driver injection is enabled I receive a group of messages (collected from different logs, screens, etc). If I turn the preinstall driver injection off things work as expected. If I leave it on I receive the following messages. windows cannot install required files 0x80004005 8004004 non zero return code ltiapply rc=31 Unhandled error returned by LTIApply: a device attached to the system is not functioning. (-2147024865 0x8007001F)

  Read the article

• Migrate an intermediate CA to a new root

  - by Tim Brigham

  Using the Microsoft CA is there any way to cut over to a new certificate authority from an intermediate authority? Both my systems are Microsoft CAs - I have a 2008 R2 Enterprise CA (intermediate) and an old 2003 CA (root). The 2003 box bit the dust and I don't have good backups. I still have a few months before the CRL expires; instead of having to cut over to a new intermediate authority is there a ready way to simply point this intermediate authority to a new offline CA?

  Read the article

• Cygwin's RSYNC for large data transfer

  - by Tim Brigham

  I'm using rsync from Cygwin to do a large scale data transfer from an aging HP MSA 1000 to a new DAS attached to a different server. I have a daemon running on the remote server in read only mode and a local copy writing the files to disk. One of my servers is an image repository with over a million files spread across about 300 directories. Each file averages only a couple hundred kilobytes. More so than any other box this one is proving problematic. The rsync process will work for a while - some times 20 minutes, some times an hour - and then it simply quits and sits idle at a given file name. I have verified that the file isn't corrupt on the remote server and that the file is successfully created on the local drive. I ran the rsync client in -vv mode, which returns nothing. I checked out the logs created by the daemon. I looked at the network utilization on the interface, which is sitting idle. I looked at the AV settings to see if anything could pose a problem there. I even updated to the latest release of Cygwin. What do I need to in order to keep this connection up? EDIT: The client system is using the command rsync.exe server::Drives/f/Repo/ /cygdrive/T/Repo --archive -P -vv The server is using the command rsync.exe --daemon --no-detach --config "rsyncd.conf" The contents of rsyncd.conf: use chroot = false strict modes = false hosts allow = 192.168.100.9 log file = c:/rsyncd.log uid=0 gid=0 [Drives] path = /cygdrive read only = yes EDIT: The file server is 2003, the disk type on the array is GPT and the size is of the array is about 4 TB. EDIT: Stranger.. It looks like the process is reliably erroring out at about 175,000 files. Rsync runs fine when I pick the same directory it has problems with one at a time. EDIT: rsync version 3.0.9 protocol version 30 Copyright (C) 1996-2011 by Andrew Tridgell, Wayne Davison, and others. Web site: http://rsync.samba.org/ Capabilities: 64-bit files, 64-bit inums, 32-bit timestamps, 64-bit long ints, no socketpairs, hardlinks, symlinks, IPv6, batchfiles, inplace, append, ACLs, xattrs, iconv, symtimes A similar failure occurred when going from the same set of files with Cygwin to a Linux install. It didn't happen until several hours later than normal however.

  Read the article

• Configure spanning tree from HP to Cisco hardware

  - by Tim Brigham

  I have three switches I'd like to configure in a loop - a Cisco stack (3750s) and two HP 2900 series. Each is connected to the next with a 10 gig backplane of one form or another. How do I configure the spanning tree on these systems to make this function correctly? From the documents I've looked at it looks like I need to set both sets of hardware to use MST mode but I'm not sure past that point. The trunking, etc is all set up as needed. HP Switch 1 A4 connected to Cisco 1/0/1. HP Switch 2 B2 connected to Cisco 2/0/1. HP Switch 1 A2 connected to HP Switch 2 A1. HP Switch 1 show spanning-tree Multiple Spanning Tree (MST) Information STP Enabled : Yes Force Version : MSTP-operation IST Mapped VLANs : 1-4094 Switch MAC Address : 0021f7-126580 Switch Priority : 32768 Max Age : 20 Max Hops : 20 Forward Delay : 15 Topology Change Count : 352,485 Time Since Last Change : 2 secs CST Root MAC Address : 0018ba-c74268 CST Root Priority : 1 CST Root Path Cost : 200000 CST Root Port : 1 IST Regional Root MAC Address : 0021f7-126580 IST Regional Root Priority : 32768 IST Regional Root Path Cost : 0 IST Remaining Hops : 20 Root Guard Ports : TCN Guard Ports : BPDU Protected Ports : BPDU Filtered Ports : PVST Protected Ports : PVST Filtered Ports : | Prio | Designated Hello Port Type | Cost rity State | Bridge Time PtP Edge ----- --------- + --------- ---- ---------- + ------------- ---- --- ---- ... A1 | Auto 128 Disabled | A2 10GbE-CX4 | 2000 128 Forwarding | 0021f7-126580 2 Yes No A3 10GbE-CX4 | Auto 128 Disabled | A4 10GbE-SR | 2000 128 Forwarding | 0021f7-126580 2 Yes No HP Switch 2 show spanning-tree Multiple Spanning Tree (MST) Information STP Enabled : Yes Force Version : MSTP-operation IST Mapped VLANs : 1-4094 Switch MAC Address : 0024a8-cd6000 Switch Priority : 32768 Max Age : 20 Max Hops : 20 Forward Delay : 15 Topology Change Count : 19,623 Time Since Last Change : 32 secs CST Root MAC Address : 0018ba-c74268 CST Root Priority : 1 CST Root Path Cost : 202000 CST Root Port : A1 IST Regional Root MAC Address : 0024a8-cd6000 IST Regional Root Priority : 32768 IST Regional Root Path Cost : 0 IST Remaining Hops : 20 Root Guard Ports : TCN Guard Ports : BPDU Protected Ports : BPDU Filtered Ports : PVST Protected Ports : PVST Filtered Ports : | Prio | Designated Hello Port Type | Cost rity State | Bridge Time PtP Edge ----- --------- + --------- ---- ---------- + ------------- ---- --- ---- ... A1 10GbE-CX4 | 2000 128 Forwarding | 0021f7-126580 2 Yes No A2 10GbE-CX4 | Auto 128 Disabled | B1 SFP+SR | 2000 128 Blocking | a44c11-a67c80 2 Yes No B2 | Auto 128 Disabled | Cisco Stack 1 show spanning-tree ... (additional VLANs) VLAN0100 Spanning tree enabled protocol ieee Root ID Priority 1 Address 0018.bac7.426e Cost 2 Port 107 (TenGigabitEthernet2/1/1) Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec Bridge ID Priority 32868 (priority 32768 sys-id-ext 100) Address a44c.11a6.7c80 Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec Aging Time 300 sec Interface Role Sts Cost Prio.Nbr Type ------------------- ---- --- --------- -------- -------------------------------- Te1/1/1 Desg FWD 2 128.53 P2p Te2/1/1 Root FWD 2 128.107 P2p

  Read the article

• Microsoft CA certificate templates expires sooner than expected

  - by Tim Brigham

  The certificates my Microsoft CA is generating do not match the time period indicated in the template used. How can I resolve this? I recently created a new certificate template for use on my Linux boxes on my Microsoft CA (2008 R2 Enterprise). This template is approved for server and client authentication purposes with a validity period of 10 years - the expected lifetime of our Linux boxes - and the subject name supplied in the request. I have checked both the intermediate and offline CA - both have more than 10 years of life listed. Is there some kind of hard limit I'm hitting here?

  Read the article

• Using 64 bit wuauclt from 32 bit command prompt

  - by Tim Brigham

  I have a script that for legacy reasons needs to run inside a 32 bit command shell. This script also includes references to certain core windows binaries - most notably wuauclt but others as well - which are not accessible by default within the 32 bit environment. This script is being run in several locations including many windows 7 and server 2008 r2 boxes. I'm aware of the possibility to copy files from the system32 to syswow64 in order to get around this. Is there any better method - something along the lines of adding an entry to the path variable - which will allow me to fall back to these 64 bit binaries from within a 32 bit script?

  Read the article

• Windows Advanced Firewall certificate based IPSEC

  - by Tim Brigham

  I'm working on migrating from using IPSEC settings stored under the 'IP Security Policies on Active Directory' to using the 'Windows Firewall with Advanced Security' for my 2008+ boxes. I have successfully been able to get this set up using Kerberos authentication, however my openswan implementation on my Linux boxes is using certificates. Whenever I try changing the authentication method to computer certificate (using RSA and my root CA) the connection is bombing out. I've made this change at both a connection request policy and on the IPSEC settings on the root Windows Firewall with Advanced Security node. The windows event log shows the authentication request is taking place but failing negotiating a mode. What am I missing here?

  Read the article

• Missing drive space in Server 2003

  - by Tim Brigham

  I have two drives used for SQL backups which for the last week have been acting strange - the free space indicated by windows is far off from what windirstat, etc indicates. There should only be about 60 GB of drive space used and there is about 160. This would match the utilization if the two last backup files were still residing on disk. SQL server is 2000, OS Server 2003 x64. Running on a VMware 5.0 cluster. OSSEC and McAfee for this system shows clean. My current plan is to temporarily attach one of these drives this drive to another VM for analysis. Is there anything more I should be looking at? There were a lot of pages on the net when I was looking for documentation on this issue but I haven't found this case described. EDIT: Unfortunately even a full reboot did not clear this behavior. I also used process explorer to look for open file handles. No dice.

  Read the article

• Puppet exported resource naming

  - by Tim Brigham

  I am working on setting up a collection of Splunk nodes to be deployed by Puppet. One of the steps in this process is importing the trusts to allow these nodes to automatically find each other. I've looked over several options and it appears that exported resources are the only ready way to go for this to work. The files I need to create are under /opt/splunk/etc/auth/distServerKeys//trusted.pem. The source for each of these files should be /opt/splunk/etc/auth/distServerKeys/trusted.pem, one per node. What syntax do I need to make this work? The samples I've looked at all appear to have the same source and destination file name.

  Read the article

• What should I do about this user?

  - by Tim Brigham

  What should I do about this user? The user is: Downloading pornography Attempting unauthorized access Running hacking software Sending unsolicited email Installing software / tampering with the system etc This is intended as a generic answer for employee behavioral problems, a la Can you help me with my software licensing question? I could see where acceptable use issues are a touch out of scope for SF, however it is one of those things most sysadmins will run into. I don't want to keep rewriting similar answers.

  Read the article

• Windows IPSec computer authentication using *user* account?

  - by Tim Brigham

  For some reason every once in a while it happens that my IPSec authentication is from a user account to a computer account, not computer to computer. How can I fix it? Sometimes - notably when I try to add a new workstation through ePO but it's happened other times as well I'm getting strange behavior from my Windows Advanced Firewall IPSec. This causes the authentication to be invalid (as the group memberships, etc all assume computer accounts). I have no idea why this is happening or how to fix it but the IDs to match up between servers (the opposite server in my second example has remote ID timb).

  Read the article

• Puppet - pass variable with a file create command

  - by Tim Brigham

  I need a way to pass a given variable - lets say thearch - to several different files within a given class. I need to be able to state the contents of this variable for each file individually. I have tried the following: file { "xxx": thearch => "i386", path => "/xxx/yyyy", owner => root, group => root, mode => 644, content => template("module/test.erb"), } This doesn't pass this variable so I can use it with a <%=thearch% statement within the erb file as I expect. What am I doing wrong here?

  Read the article

• Duplicate of IPSEC certificate template not displaying

  - by Tim Brigham

  I am working on getting IPSEC working on computers outside my domain. I am unable to get a duplicate of the IPSec Offline Request template to show on the web interface. My CA is 2008 R2 Enterprise and the permissions on the template should be adequate to allow me access (my account has read and enroll). If I publish the original template it functions as desired. I also have other custom templates in use (although using autoenrollment). The duplicate is almost identical to the original, excepting that it has a longer validity period and the private key is marked as exportable. How do I debug at this point?

  Read the article

• Manage Kickstart library with Puppet

  - by Tim Brigham

  I maintain a library of different kickstart configurations, mostly for CentOS 5 and 6. It has recently gotten to the point I want to deduplicate as much of this information as possible. I am aware of a couple options out there which can dynamically generate kickstart files. Not interested at this point unless I really need to do that route. I would like to create my Kickstart files using a template along the following line: deploy1-centos5.erb .... install=http://.../$arch/... repo=http://.../$arch/... .... My output naming schema is "deploy1-centos5-x86_64". I'd like to be able to create several kickstart files from a given template, one for 32 bit, one 64, ppc, etc. This would work perfectly if I could readily set the value of arch per each time the template is called to create a file. What is the most ready way to address this?

  Read the article

• html5 video and Windows 7N

  - by Tim Brigham

  When using Windows 7N and embedded videos for YouTube and the like my users have been getting a black box. I tracked this down to when HTML5 is being used for rendering. Other than putting a bunch of sites in compatibility mode or installing the Windows Media Pack (which resolves this issue) is there another route I can take? My guess is it's only a single registry key or DLL that says 'I'm not HTML5 compatible' but I don't have any idea how to find it.

  Read the article

• Augeas - create new ini section

  - by Tim Brigham

  I have a config file in augeas using a custom lens that outputs the data as follows. /files/opt/../server.conf/target[1] = "general" /files/opt/../server.conf/target[1]/serverName = "XXX" /files/opt/../server.conf/target[1]/guid = "XXX0XXX" /files/opt/../server.conf/target[2] = "sslConfig" /files/opt/../server.conf/target[2]/sslKeysfilePassword = "$1$XXXXX" This works well - some of the target names contain colons, etc so I need to use the target[x] format. What is the correct ins syntax to create a new section in my INI using this syntax?

  Read the article

• conf.lua not being read (Lua/LOVE 0.8.0)

  - by Brigham Andersen

  I need a higher resolution for my program to run. For some reason I cannot discern alone, LOVE is not applying (or finding?) conf.lua. My folder architecture is as follows: basefolder/ basefolder/main.lua basefolder/conf.lua basefolder/Resources/ My conf.lua reads: function love.conf(t) t.window.width = 1280 t.window.height = 720 end Is it something with my code, or with how my directory is set up?

  Read the article

• Extract Generic types from extended Generic

  - by Brigham

  I'm trying to refactor a class and set of subclasses where the M type does extend anything, even though we know it has to be a subclass of a certain type. That type is parametrized and I would like its parametrized types to be available to subclasses that already have values for M. Is there any way to define this class without having to include the redundant K and V generic types in the parameter list. I'd like to be able to have the compiler infer them from whatever M is mapped to by subclasses. public abstract class NewParametrized<K, V, M extends SomeParametrized<K, V>> { public void someMethodThatTakesKAndV(K k1, V v1) { } } In other words, I'd like the class declaration to look something like: public class NewParametrized<M extends SomeParametrized<K, V>> { And K and V's types would be inferred from the definition of M.

  Read the article

• Get to Know a Candidate (7 of 25): Will Christensen&ndash;Independent American Party

  - by Brian Lanham

  DISCLAIMER: This is not a post about “Romney” or “Obama”. This is not a post for whom I am voting. Information sourced for Wikipedia. NOTE: Wikipedia does not have a page for Christensen.  If you follow links to the party site you can find information about him. Christensen served in the United States Marine Corps and has degrees from Penn State University (my alma mater), Drexel Institute of Technology, University of Utah, and Brigham Young University (BYU) focusing on Math, Physics, and Electrical Engineering.  He has worked for IBM and BYU but for the last 35 years has run small businesses including an Internet book business as well as an Amway franchise. He has held numerous offices in various political parties including, County Campaign Chairman for Barry Goldwater in 1964, County Central Committee, Republican Party; National Committeeman, and State Chairman of the American Party; one of the Founders, and the State Chairman of the Independent American Party of Utah; Vice-Chairman, Chairman, and the Treasurer of the National Independent American Party. The Independent American Party (IAP) officially started in 1998 and began as the Utah Independent American Party. The founders claim to have been inspired by a speech given by Ezra Taft Benson, former United States Secretary of Agriculture, entitled “The Proper Role of Government”. The 15 principles for the proper role of government, taken from his speech, are held as the IAP’s basis for recruiting. Learn more about the Independent American Party on Wikipedia.

  Read the article

• Lucene - querying with long strings

  - by Mikos

  I have an index, with a field "Affiliation", some example values are: "Stanford University School of Medicine, Palo Alto, CA USA", "Institute of Neurobiology, School of Medicine, Stanford University, Palo Alto, CA", "School of Medicine, Harvard University, Boston MA", "Brigham & Women's, Harvard University School of Medicine, Boston, MA" "Harvard University, Cambridge MA" and so on... (the bottom-line being the affiliations are written in multiple ways with no apparent consistency) I query the index on the affiliation field using say "School of Medicine, Stanford University, Palo Alto, CA" (with QueryParser) to find all Stanford related documents, I get a lot of false +ves, presumably because of the presence of School of Medicine etc. etc. (note: I cannot use Phrase query because of variability in the way affiliation is constructed) I have tried the following: Use a SpanNearQuery by splitting the search phrase with a whitespace (here I get no results!) Tried boosting (using ^) by splitting with the comma and boosting the last parts such as "Palo Alto CA" with a much higher boost than the initial phrases. Here I still get lots of false +ves. Any suggestions on how to approach this? If SpanNearQuery the way to go, Any ideas on why I get 0 results?

  Read the article

1